Fix st7703 panel initialization failures
cover Fix st7703 panel initialization failures
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdf
Please take a look.
thank you and regards,
Ondrej Jirman
Ondrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the panel
drivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)
Signature · 1 line
2.27.0
PATCH 1/2 drm/panel: st7703: Make the sleep exit timing match the spec
The driver seemed to try to make the total cumulative time of all delays across the whole power up sequence to sum up to 120ms.
The datasheet on the other hand specifies that there needs to be 120ms delay after the sleep out command, not after reset as the driver assumes.
Lastly, the delay between init commands and the sleep exit command is not necessary. (not specified anywhere)
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +2 -5
@@ -291,7 +291,6 @@ static int xbd599_init_sequence(struct st7703 *ctx)dsi_dcs_write_seq (dsi,ST7703_CMD_SETBGP ,0x07 ,/* VREF_SEL = 4.2V */ 0x07 /* NVREF_SEL = 4.2V */ ); -msleep (20 ); dsi_dcs_write_seq(dsi, ST7703_CMD_SETVCOM, 0x2C, /* VCOMDC_F = -0.67V */
@@ -369,16 +368,14 @@ static int st7703_enable(struct drm_panel *panel)return ret; } -msleep (20 ); - ret =mipi_dsi_dcs_exit_sleep_mode (dsi);if (ret <0 ) {DRM_DEV_ERROR (ctx->dev,"Failed to exit sleep mode: %d\n" , ret);return ret; } -/* Panel is operational 120 msec after reset */ -msleep (60 ); +/* Dsiplay on can be issued 120 msec after sleep out */ +msleep (120 ); ret =mipi_dsi_dcs_set_display_on (dsi);if (ret)
Signature · 1 line
2.27.0
PATCH 2/2 drm/panel: st7703: Fix the power up sequence of the panel
In reply to Ondrej JirmanThe datasheet specifies that it's better to keep reset asserted while powering up the supplies, and that IOVCC should be enabled first.
There also needs to be a delay after enabling the supplies and before deasserting the reset. The datasheet specifies 1ms after the supplies reach the required voltage. Use 10-20ms to also give the power supplies some time to reach the required voltage, too.
This fixes intermittent panel initialization failures and screen corruption during resume from sleep on PinePhone.
--- drivers/gpu/drm/panel/panel-sitronix-st7703.c | 22 +++++++++++-------- 1 file changed, 13 insertions(+), 9 deletions(-)
drivers/gpu/drm/panel/panel-sitronix-st7703.c +13 -9
@@ -429,12 +429,8 @@ static int st7703_prepare(struct drm_panel *panel)return 0 ;DRM_DEV_DEBUG_DRIVER (ctx->dev,"Resetting the panel\n" ); - ret =regulator_enable (ctx->vcc); -if (ret <0 ) { -DRM_DEV_ERROR (ctx->dev, -"Failed to enable vcc supply: %d\n" , ret); -return ret; - } +gpiod_set_value_cansleep (ctx->reset_gpio,1 ); + ret =regulator_enable (ctx->iovcc);if (ret <0 ) { DRM_DEV_ERROR(ctx->dev,
@@ -442,10 +438,18 @@ static int st7703_prepare(struct drm_panel *panel) goto disable_vcc; } -gpiod_set_value_cansleep (ctx->reset_gpio,1 ); -usleep_range (20 ,40 ); + ret =regulator_enable (ctx->vcc); +if (ret <0 ) { +DRM_DEV_ERROR (ctx->dev, +"Failed to enable vcc supply: %d\n" , ret); +return ret; + } + +/* Give power supplies time to stabilize before deasserting reset. */ +usleep_range (10000 ,20000 ); +gpiod_set_value_cansleep (ctx->reset_gpio,0 ); -msleep (20 ); +usleep_range (15000 ,20000 ); ctx->prepared = true;
Signature · 1 line
2.27.0
Guido Günther
maintainerHi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
Cheers,
-- Guido
Quoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
Hi Guido,
Quoted 10 lines · Guido Günther
Hi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Quoted 4 lines
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
It should work on rocktech too. The patch mostly increases/reorders the delays slightly, to match the controller documentation. I don't see a reason to complicate the driver with per panel special delays, unless these patches don't work on your panel.
The init sequence is still suboptimal, and doesn't follow the kernel docs completely, even after these patches. Controller spec also talks about adding some delay before enabling the backlight to avoid visual glitches.
Which is what enable callback is documented to be for. Currently part of the initialization that belongs to prepare callback is also done in enable callback.
I see the glitch (small vertical shift of the image on powerup), but personally don't care much to introduce even more delays to the driver, just for the cosmetic issue.
regards,
o.
Quoted 31 lines
Cheers,
-- GuidoQuoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
Guido Günther
maintainerHi,
Quoted 18 lines · Ondřej Jirman
Hi Guido,
Quoted 10 lines · Guido Günther
Hi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Quoted 4 lines
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
Quoted 4 lines
It should work on rocktech too. The patch mostly increases/reorders the delays slightly, to match the controller documentation. I don't see a reason to complicate the driver with per panel special delays, unless these patches don't work on your panel.
That's why i brought it up. It breaks the rocktech panel on blank/unblank loops where it just stays blank and then starts hitting DSI command timeouts.
Cheers,
-- Guido
Quoted 8 lines
The init sequence is still suboptimal, and doesn't follow the kernel docs completely, even after these patches. Controller spec also talks about adding some delay before enabling the backlight to avoid visual glitches.
Which is what enable callback is documented to be for. Currently part of the initialization that belongs to prepare callback is also done in enable callback.
Quoted 39 lines
I see the glitch (small vertical shift of the image on powerup), but personally don't care much to introduce even more delays to the driver, just for the cosmetic issue.
regards,
o.Quoted 31 lines
Cheers,
-- GuidoQuoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
Hello,
Quoted 20 lines · Guido Günther
Hi,
Quoted 18 lines · Ondřej Jirman
Hi Guido,
Quoted 14 lines · Guido Günther
Hi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
Quoted 8 lines
Quoted 4 lines
It should work on rocktech too. The patch mostly increases/reorders the delays slightly, to match the controller documentation. I don't see a reason to complicate the driver with per panel special delays, unless these patches don't work on your panel.
That's why i brought it up. It breaks the rocktech panel on blank/unblank loops where it just stays blank and then starts hitting DSI command timeouts.
Good to know. Does keeping the msleep(20); after init sequence and before sleep exit make it work?
thank you and regards,
o.
Quoted 50 lines
Cheers,
-- GuidoQuoted 47 lines
The init sequence is still suboptimal, and doesn't follow the kernel docs completely, even after these patches. Controller spec also talks about adding some delay before enabling the backlight to avoid visual glitches.
Which is what enable callback is documented to be for. Currently part of the initialization that belongs to prepare callback is also done in enable callback.
I see the glitch (small vertical shift of the image on powerup), but personally don't care much to introduce even more delays to the driver, just for the cosmetic issue.
regards,
o.Quoted 31 lines
Cheers,
-- GuidoQuoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
Guido Günther
maintainerHi,
Quoted 28 lines · Ondřej Jirman
Hello,
Quoted 25 lines · Guido Günther
Hi,
Quoted 22 lines · Ondřej Jirman
Hi Guido,
Quoted 10 lines · Guido Günther
Hi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Quoted 4 lines
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
It should work on rocktech too. The patch mostly increases/reorders the delays slightly, to match the controller documentation. I don't see a reason to complicate the driver with per panel special delays, unless these patches don't work on your panel.
Quoted 6 lines
Quoted 3 lines
That's why i brought it up. It breaks the rocktech panel on blank/unblank loops where it just stays blank and then starts hitting DSI command timeouts.
Good to know. Does keeping the msleep(20); after init sequence and before sleep exit make it work?
We need both sleeps to make this work reliably so basically reverting your 'drm/panel: st7703: Make the sleep exit timing match the spec' makes things stable again.
We don't need to sleep 120ms after sleep out though since our panel only requires 15ms as per data sheet there so it really makes sense to make these configurable.
Cheers,
-- Guido
Quoted 55 lines
thank you and regards,
o.Quoted 50 lines
Cheers,
-- GuidoQuoted 47 lines
The init sequence is still suboptimal, and doesn't follow the kernel docs completely, even after these patches. Controller spec also talks about adding some delay before enabling the backlight to avoid visual glitches.
Which is what enable callback is documented to be for. Currently part of the initialization that belongs to prepare callback is also done in enable callback.
I see the glitch (small vertical shift of the image on powerup), but personally don't care much to introduce even more delays to the driver, just for the cosmetic issue.
regards,
o.Quoted 31 lines
Cheers,
-- GuidoQuoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
Hello,
Quoted 37 lines · Guido Günther
Hi,
Quoted 28 lines · Ondřej Jirman
Hello,
Quoted 25 lines · Guido Günther
Hi,
Quoted 22 lines · Ondřej Jirman
Hi Guido,
Quoted 10 lines · Guido Günther
Hi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Quoted 4 lines
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
It should work on rocktech too. The patch mostly increases/reorders the delays slightly, to match the controller documentation. I don't see a reason to complicate the driver with per panel special delays, unless these patches don't work on your panel.
Quoted 6 lines
Quoted 3 lines
That's why i brought it up. It breaks the rocktech panel on blank/unblank loops where it just stays blank and then starts hitting DSI command timeouts.
Good to know. Does keeping the msleep(20); after init sequence and before sleep exit make it work?
Quoted 7 lines
We need both sleeps to make this work reliably so basically reverting your 'drm/panel: st7703: Make the sleep exit timing match the spec' makes things stable again.
We don't need to sleep 120ms after sleep out though since our panel only requires 15ms as per data sheet there so it really makes sense to make these configurable.
Thank you for checking it.
I'd be happy with just the other patch being applied. That would be enough to fix issues with xingbangda panel too.
In my tests xbd panel doesn't need 120ms either, despite the datasheet. What breaks xbd panel is the lack of post-powerup delay before deasserting reset line.
regards,
o.
Quoted 58 lines
Cheers,
-- GuidoQuoted 55 lines
thank you and regards,
o.Quoted 50 lines
Cheers,
-- GuidoQuoted 47 lines
The init sequence is still suboptimal, and doesn't follow the kernel docs completely, even after these patches. Controller spec also talks about adding some delay before enabling the backlight to avoid visual glitches.
Which is what enable callback is documented to be for. Currently part of the initialization that belongs to prepare callback is also done in enable callback.
I see the glitch (small vertical shift of the image on powerup), but personally don't care much to introduce even more delays to the driver, just for the cosmetic issue.
regards,
o.Quoted 31 lines
Cheers,
-- GuidoQuoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
Guido Günther
maintainerHi Ondřej,
Quoted 44 lines · Ondřej Jirman
Hello,
Quoted 41 lines · Guido Günther
Hi,
Quoted 28 lines · Ondřej Jirman
Hello,
Quoted 25 lines · Guido Günther
Hi,
Quoted 22 lines · Ondřej Jirman
Hi Guido,
Quoted 10 lines · Guido Günther
Hi Ondrej,
Quoted 7 lines · Ondrej Jirman
When extending the driver for xbd599 panel support I tried to do minimal changes and keep the existing initialization timing.
It turned out that it's not good enough and the existing init sequence is too aggressive and doesn't follow the specification. On PinePhone panel is being powered down/up during suspend/resume and with current timings this frequently leads to corrupted display.
Quoted 4 lines
Given the amount of ST7703 look alikes i don't think you can go by the datasheet and hope not to break other panels. The current sleeps cater for the rocktech panel (which suffered from similar issues you describe when we took other parameters) so you need to make those panel specific.
It should work on rocktech too. The patch mostly increases/reorders the delays slightly, to match the controller documentation. I don't see a reason to complicate the driver with per panel special delays, unless these patches don't work on your panel.
Quoted 6 lines
Quoted 3 lines
That's why i brought it up. It breaks the rocktech panel on blank/unblank loops where it just stays blank and then starts hitting DSI command timeouts.
Good to know. Does keeping the msleep(20); after init sequence and before sleep exit make it work?
We need both sleeps to make this work reliably so basically reverting your 'drm/panel: st7703: Make the sleep exit timing match the spec' makes things stable again.
Quoted 8 lines
Quoted 3 lines
We don't need to sleep 120ms after sleep out though since our panel only requires 15ms as per data sheet there so it really makes sense to make these configurable.
Thank you for checking it.
I'd be happy with just the other patch being applied. That would be enough to fix issues with xingbangda panel too.
That's fine since that case works here too. The commit message should be adjusted though since the ST7703 data sheet i'm looking at says there's no restriction about applying IOVCC and VCI (tRPW= +/- no limit). You're basically also switching to another reset pattern (the data sheet describes two). So instead of saying:
"Fix the power up sequence of the panel"
i'd rather say
"Pick a reset sequence that works for ingbangda,xbd599 panel too"
and then describe the changes since that helps us to identify later on why we made that change. With that and 1/2 dropped that looks good to me.
Cheers,
-- Guido
Quoted 68 lines
In my tests xbd panel doesn't need 120ms either, despite the datasheet. What breaks xbd panel is the lack of post-powerup delay before deasserting reset line.
regards,
o.Quoted 58 lines
Cheers,
-- GuidoQuoted 55 lines
thank you and regards,
o.Quoted 50 lines
Cheers,
-- GuidoQuoted 47 lines
The init sequence is still suboptimal, and doesn't follow the kernel docs completely, even after these patches. Controller spec also talks about adding some delay before enabling the backlight to avoid visual glitches.
Which is what enable callback is documented to be for. Currently part of the initialization that belongs to prepare callback is also done in enable callback.
I see the glitch (small vertical shift of the image on powerup), but personally don't care much to introduce even more delays to the driver, just for the cosmetic issue.
regards,
o.Quoted 31 lines
Cheers,
-- GuidoQuoted 28 lines
This patch series fixes the problems.
The issue was reported by Samuel Holland.
Relevant screenshots from the datasheet:
Power on timing: https://megous.com/dl/tmp/35b72e674ce0ca27.png
Power off timing: https://megous.com/dl/tmp/dea195517106ff17.png
More optimal reset on poweron: https://megous.com/dl/tmp/a9e5caf14e1b0dc6.png
Less optimal reset on poweron: https://megous.com/dl/tmp/246761039283c4cf.png
Datasheet: https://megous.com/dl/tmp/ST7703_DS_v01_20160128.pdfPlease take a look.
thank you and regards,
Ondrej JirmanOndrej Jirman (2):
drm/panel: st7703: Make the sleep exit timing match the spec drm/panel: st7703: Fix the power up sequence of the paneldrivers/gpu/drm/panel/panel-sitronix-st7703.c | 29 ++++++++++--------- 1 file changed, 15 insertions(+), 14 deletions(-)Signature · 1 line
2.27.0
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel