Skip to contentSkip to conversation

Introduce B1x5v2 support

PATCH New Sebastian Reichel 4 participants 23 messages Sep 2, 2020 – Nov 2, 2020

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v4 cover Introduce B1x5v2 support

This series introduces support for a new i.MX6DL based GE patient monitor series.

Patch 1: Add support for storing bootcount in SPI-flash Patch 2+3: Improve M41T62 RTC driver's reset routine. PATCH 4: Support disable_ldb_di_clock_sources for i.MX6DL Patch 5: Add poweroff-gpio support
Patch 6-8: restructure common GE code
Patch 9: Add the actual board, using SPL and DM

Changes since PATCHv3 [0]:
* Dropped patch for reading DR for i.MX GPIOs and set SION pinmux bits in B1x5v2 output GPIOs instead
* Rebased to v2020.10-rc3

Changes since PATCHv2:

* PATCH 10: Fixed network phy mode ("rgmii" -> "rgmii-id")
* PATCH 6: Fixed nits reported by Simon Glass and added is Reviewed-by Tag.

Changes since PATCHv1:

* Rebased to v2020.10-rc2
* Original patch 1 (support for DM_SPI_FLASH with non-DM SPL) has been dropped, since a similar patch has been merged in the meantime
* poweroff-gpio support is now added using sysreset uclass instead of introducing a new poweroff uclass
* B1x5v2 patch has been updated to follow recent U-Boot changes and to add USB mass storage support

[0] http://patchwork.ozlabs.org/project/uboot/list/?series=196979

-- Sebastian

Sebastian Reichel (9):
bootcount: add a DM SPI flash backing store for bootcount
rtc: m41t62: reset SQW in m41t62_rtc_reset
rtc: m41t62: add oscillator fail bit reset support
imx6: allow usage of disable_ldb_di_clock_sources for CONFIG_MX6QDL
sysreset: Add poweroff-gpio driver
board: ge: common: rename ge_common.c to ge_rtc.c
board: ge: common: add config option for RTC and VPD feature
board: ge: common: vpd: separate I2C specific code
board: ge: b1x5v2: Add GE B1x5v2 and B1x5Pv2

 arch/arm/dts/Makefile                     |   1 +
 arch/arm/dts/imx6dl-b1x5v2.dts            | 654 ++++++++++++++++++++
 arch/arm/mach-imx/mx6/Kconfig             |   9 +
 arch/arm/mach-imx/mx6/clock.c             |   2 +-
 board/ge/b1x5v2/Kconfig                   |  14 +
 board/ge/b1x5v2/Makefile                  |   6 +
 board/ge/b1x5v2/b1x5v2.c                  | 698 ++++++++++++++++++++++
 board/ge/b1x5v2/spl.c                     | 587 ++++++++++++++++++
 board/ge/bx50v3/Kconfig                   |   2 +
 board/ge/bx50v3/bx50v3.c                  |   4 +-
 board/ge/common/Kconfig                   |   7 +
 board/ge/common/Makefile                  |   3 +-
 board/ge/common/{ge_common.c => ge_rtc.c} |   0
 board/ge/common/{ge_common.h => ge_rtc.h} |   0
 board/ge/common/vpd_reader.c              |  12 +-
 board/ge/common/vpd_reader.h              |  23 +-
 board/ge/mx53ppd/Kconfig                  |   2 +
 board/ge/mx53ppd/mx53ppd.c                |   4 +-
 configs/ge_b1x5v2_defconfig               | 137 +++++
 drivers/bootcount/Kconfig                 |  10 +
 drivers/bootcount/Makefile                |   1 +
 drivers/bootcount/spi-flash.c             | 125 ++++
 drivers/rtc/m41t62.c                      | 139 ++++-
 drivers/sysreset/Kconfig                  |   7 +
 drivers/sysreset/Makefile                 |   1 +
 drivers/sysreset/poweroff_gpio.c          |  92 +++
 include/configs/ge_b1x5v2.h               | 127 ++++
 27 files changed, 2645 insertions(+), 22 deletions(-)
 create mode 100644 arch/arm/dts/imx6dl-b1x5v2.dts
 create mode 100644 board/ge/b1x5v2/Kconfig
 create mode 100644 board/ge/b1x5v2/Makefile
 create mode 100644 board/ge/b1x5v2/b1x5v2.c
 create mode 100644 board/ge/b1x5v2/spl.c
 create mode 100644 board/ge/common/Kconfig
 rename board/ge/common/{ge_common.c => ge_rtc.c} (100%)
 rename board/ge/common/{ge_common.h => ge_rtc.h} (100%)
 create mode 100644 configs/ge_b1x5v2_defconfig
 create mode 100644 drivers/bootcount/spi-flash.c
 create mode 100644 drivers/sysreset/poweroff_gpio.c
 create mode 100644 include/configs/ge_b1x5v2.h
Signature · 1 line
2.28.0
#1 lore raw

PATCH v4 1/9 bootcount: add a DM SPI flash backing store for bootcount

This driver allows to use SPI flash as backing store for boot counter values with DM enabled.

---
 drivers/bootcount/Kconfig     |  10 +++
 drivers/bootcount/Makefile    |   1 +
 drivers/bootcount/spi-flash.c | 125 ++++++++++++++++++++++++++++++++++
 3 files changed, 136 insertions(+)
 create mode 100644 drivers/bootcount/spi-flash.c
drivers/bootcount/Kconfig +10 -0
index c8e6fa7f8925..b5ccea0d9c20 100644
@@ -108,6 +108,16 @@ config DM_BOOTCOUNT_I2C_EEPROM
 	  pointing to the underlying i2c eeprom device) and an optional 'offset'
 	  property are supported.
 
+config DM_BOOTCOUNT_SPI_FLASH
+	bool "Support SPI flash devices as a backing store for bootcount"
+	depends on DM_SPI_FLASH
+	help
+	  Enabled reading/writing the bootcount in a DM SPI flash device.
+	  The wrapper device is to be specified with the compatible string
+	  'u-boot,bootcount-spi-flash' and the 'spi-flash'-property (a phandle
+	  pointing to the underlying SPI flash device) and an optional 'offset'
+	  property are supported.
+
 config BOOTCOUNT_MEM
 	bool "Support memory based bootcounter"
 	help
drivers/bootcount/Makefile +1 -0
index 059d40d16b0c..51d860b00e18 100644
@@ -12,3 +12,4 @@ obj-$(CONFIG_BOOTCOUNT_EXT)	+= bootcount_ext.o
 obj-$(CONFIG_DM_BOOTCOUNT)      += bootcount-uclass.o
 obj-$(CONFIG_DM_BOOTCOUNT_RTC)  += rtc.o
 obj-$(CONFIG_DM_BOOTCOUNT_I2C_EEPROM)	+= i2c-eeprom.o
+obj-$(CONFIG_DM_BOOTCOUNT_SPI_FLASH)	+= spi-flash.o
drivers/bootcount/spi-flash.c new file +125 -0

125 lines not on this page · raw message

Signature · 1 line
2.28.0
#2 lore raw

PATCH v4 1/9 bootcount: add a DM SPI flash backing store for bootcount

Quoted 3 lines

This driver allows to use SPI flash as backing store for boot counter values with DM enabled.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#3 lore raw

PATCH v4 2/9 rtc: m41t62: reset SQW in m41t62_rtc_reset

In reply to Sebastian Reichel

This takes care of resetting the 32kHz square wave, which is used by some boards as clock source for the SoC.

---
 drivers/rtc/m41t62.c | 89 +++++++++++++++++++++++++++++++++++++++++---
 1 file changed, 83 insertions(+), 6 deletions(-)
drivers/rtc/m41t62.c +83 -6
index 94a6b523aab3..85d6eb02593f 100644
@@ -22,6 +22,7 @@
 #include <log.h>
 #include <rtc.h>
 #include <i2c.h>
+#include <linux/log2.h>
 
 #define M41T62_REG_SSEC	0
 #define M41T62_REG_SEC	1
@@ -49,6 +50,11 @@
 #define M41T62_FLAGS_AF		(1 << 6)	/* AF: Alarm Flag Bit */
 #define M41T62_FLAGS_BATT_LOW	(1 << 4)	/* BL: Battery Low Bit */
 
+#define M41T62_WDAY_SQW_FREQ_MASK	0xf0
+#define M41T62_WDAY_SQW_FREQ_SHIFT	4
+
+#define M41T62_SQW_MAX_FREQ	32768
+
 #define M41T62_FEATURE_HT	(1 << 0)
 #define M41T62_FEATURE_BL	(1 << 1)
 
@@ -139,21 +145,92 @@ static int m41t62_rtc_set(struct udevice *dev, const struct rtc_time *tm)
 	return 0;
 }
 
-static int m41t62_rtc_reset(struct udevice *dev)
+static int m41t62_sqw_enable(struct udevice *dev, bool enable)
+{
+	u8 val;
+	int ret;
+
+	ret = dm_i2c_read(dev, M41T62_REG_ALARM_MON, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	if (enable)
+		val |= M41T62_ALMON_SQWE;
+	else
+		val &= ~M41T62_ALMON_SQWE;
+
+	return dm_i2c_write(dev, M41T62_REG_ALARM_MON, &val, sizeof(val));
+}
+
+static int m41t62_sqw_set_rate(struct udevice *dev, unsigned int rate)
+{
+	u8 val, newval, sqwrateval;
+	int ret;
+
+	if (rate >= M41T62_SQW_MAX_FREQ)
+		sqwrateval = 1;
+	else if (rate >= M41T62_SQW_MAX_FREQ / 4)
+		sqwrateval = 2;
+	else if (rate)
+		sqwrateval = 15 - ilog2(rate);
+
+	ret = dm_i2c_read(dev, M41T62_REG_WDAY, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	newval = val;
+	newval &= ~M41T62_WDAY_SQW_FREQ_MASK;
+	newval |= (sqwrateval << M41T62_WDAY_SQW_FREQ_SHIFT);
+
+	/*
+	 * Try to avoid writing unchanged values. Writing to this register
+	 * will reset the internal counter pipeline and thus affect system
+	 * time.
+	 */
+	if (newval == val)
+		return 0;
+
+	return dm_i2c_write(dev, M41T62_REG_WDAY, &newval, sizeof(newval));
+}
+
+static int m41t62_rtc_clear_ht(struct udevice *dev)
 {
 	u8 val;
+	int ret;
 
 	/*
 	 * M41T82: Make sure HT (Halt Update) bit is cleared.
 	 * This bit is 0 in M41T62 so its save to clear it always.
 	 */
 
-	int ret = dm_i2c_read(dev, M41T62_REG_ALARM_HOUR, &val, sizeof(val));
-
+	ret = dm_i2c_read(dev, M41T62_REG_ALARM_HOUR, &val, sizeof(val));
+	if (ret)
+		return ret;
 	val &= ~M41T80_ALHOUR_HT;
-	ret |= dm_i2c_write(dev, M41T62_REG_ALARM_HOUR, &val, sizeof(val));
+	ret = dm_i2c_write(dev, M41T62_REG_ALARM_HOUR, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	return 0;
+}
 
-	return ret;
+static int m41t62_rtc_reset(struct udevice *dev)
+{
+	int ret;
+
+	ret = m41t62_rtc_clear_ht(dev);
+	if (ret)
+		return ret;
+
+	/*
+	 * Some boards feed the square wave as clock input into
+	 * the SoC. This enables a 32.768kHz square wave, which is
+	 * also the hardware default after power-loss.
+	 */
+	ret = m41t62_sqw_set_rate(dev, 32768);
+	if (ret)
+		return ret;
+	return m41t62_sqw_enable(dev, true);
 }
 
 /*
@@ -162,7 +239,7 @@ static int m41t62_rtc_reset(struct udevice *dev)
  */
 static int m41t62_rtc_probe(struct udevice *dev)
 {
-	return m41t62_rtc_reset(dev);
+	return m41t62_rtc_clear_ht(dev);
 }
 
 static const struct rtc_ops m41t62_rtc_ops = {
Signature · 1 line
2.28.0
#4 lore raw

PATCH v4 2/9 rtc: m41t62: reset SQW in m41t62_rtc_reset

Quoted 3 lines

This takes care of resetting the 32kHz square wave, which is used by some boards as clock source for the SoC.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#5 lore raw

PATCH v4 3/9 rtc: m41t62: add oscillator fail bit reset support

In reply to Sebastian Reichel

In case of empty battery or glitches the oscillator fail bit might be set. This will reset the bit in the reset routine.

---
 drivers/rtc/m41t62.c | 50 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)
drivers/rtc/m41t62.c +50 -0
index 85d6eb02593f..0a4e12d69827 100644
@@ -23,6 +23,7 @@
 #include <rtc.h>
 #include <i2c.h>
 #include <linux/log2.h>
+#include <linux/delay.h>
 
 #define M41T62_REG_SSEC	0
 #define M41T62_REG_SEC	1
@@ -48,6 +49,7 @@
 #define M41T62_ALMON_SQWE	(1 << 6)	/* SQWE: SQW Enable Bit */
 #define M41T62_ALHOUR_HT	(1 << 6)	/* HT: Halt Update Bit */
 #define M41T62_FLAGS_AF		(1 << 6)	/* AF: Alarm Flag Bit */
+#define M41T62_FLAGS_OF		(1 << 2)	/* OF: Oscillator Flag Bit */
 #define M41T62_FLAGS_BATT_LOW	(1 << 4)	/* BL: Battery Low Bit */
 
 #define M41T62_WDAY_SQW_FREQ_MASK	0xf0
@@ -193,6 +195,50 @@ static int m41t62_sqw_set_rate(struct udevice *dev, unsigned int rate)
 	return dm_i2c_write(dev, M41T62_REG_WDAY, &newval, sizeof(newval));
 }
 
+static int m41t62_rtc_restart_osc(struct udevice *dev)
+{
+	u8 val;
+	int ret;
+
+	/* 0. check if oscillator failure happened */
+	ret = dm_i2c_read(dev, M41T62_REG_FLAGS, &val, sizeof(val));
+	if (ret)
+		return ret;
+	if (!(val & M41T62_FLAGS_OF))
+		return 0;
+
+	ret = dm_i2c_read(dev, M41T62_REG_SEC, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	/* 1. Set stop bit */
+	val |= M41T62_SEC_ST;
+	ret = dm_i2c_write(dev, M41T62_REG_ALARM_HOUR, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	/* 2. Clear stop bit */
+	val &= ~M41T62_SEC_ST;
+	ret = dm_i2c_write(dev, M41T62_REG_ALARM_HOUR, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	/* 3. wait 4 seconds */
+	mdelay(4000);
+
+	ret = dm_i2c_read(dev, M41T62_REG_FLAGS, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	/* 4. clear M41T62_FLAGS_OF bit */
+	val &= ~M41T62_FLAGS_OF;
+	ret = dm_i2c_write(dev, M41T62_REG_FLAGS, &val, sizeof(val));
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
 static int m41t62_rtc_clear_ht(struct udevice *dev)
 {
 	u8 val;
@@ -218,6 +264,10 @@ static int m41t62_rtc_reset(struct udevice *dev)
 {
 	int ret;
 
+	ret = m41t62_rtc_restart_osc(dev);
+	if (ret)
+		return ret;
+
 	ret = m41t62_rtc_clear_ht(dev);
 	if (ret)
 		return ret;
Signature · 1 line
2.28.0
#6 lore raw

PATCH v4 3/9 rtc: m41t62: add oscillator fail bit reset support

Quoted 4 lines

In case of empty battery or glitches the oscillator fail bit might be set. This will reset the bit in the reset routine.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#7 lore raw

PATCH v4 4/9 imx6: allow usage of disable_ldb_di_clock_sources for CONFIG_MX6QDL

In reply to Sebastian Reichel

Allow using disable_ldb_di_clock_sources with just the combined CONFIG_MX6QDL being enabled.

---
 arch/arm/mach-imx/mx6/clock.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/mach-imx/mx6/clock.c +1 -1
index fb5e5b6f05c4..cb9d629be408 100644
@@ -1341,7 +1341,7 @@ int do_mx6_showclocks(struct cmd_tbl *cmdtp, int flag, int argc,
 }
 
 #if defined(CONFIG_MX6Q) || defined(CONFIG_MX6D) || defined(CONFIG_MX6DL) || \
-	defined(CONFIG_MX6S)
+	defined(CONFIG_MX6S) || defined(CONFIG_MX6QDL)
 static void disable_ldb_di_clock_sources(void)
 {
 	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
Signature · 1 line
2.28.0
#8 lore raw

PATCH v4 4/9 imx6: allow usage of disable_ldb_di_clock_sources for CONFIG_MX6QDL

Quoted 3 lines

Allow using disable_ldb_di_clock_sources with just the combined CONFIG_MX6QDL being enabled.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#9 lore raw

PATCH v4 5/9 sysreset: Add poweroff-gpio driver

In reply to Sebastian Reichel

Add GPIO poweroff driver, which is based on the Linux driver and uses the same DT binding.

---
 drivers/sysreset/Kconfig         |  7 +++
 drivers/sysreset/Makefile        |  1 +
 drivers/sysreset/poweroff_gpio.c | 92 ++++++++++++++++++++++++++++++++
 3 files changed, 100 insertions(+)
 create mode 100644 drivers/sysreset/poweroff_gpio.c
drivers/sysreset/Kconfig +7 -0
index 6ebc90e1d33b..bf042f32c848 100644
@@ -43,6 +43,13 @@ config SYSRESET_CMD_POWEROFF
 
 endif
 
+config POWEROFF_GPIO
+	bool "Enable support for GPIO poweroff driver"
+	select DM_GPIO
+	help
+	  Support for system poweroff using a GPIO pin. This can be used
+	  for systems having a single GPIO to trigger a system poweroff.
+
 config SYSRESET_GPIO
 	bool "Enable support for GPIO reset driver"
 	select DM_GPIO
drivers/sysreset/Makefile +1 -0
index df2293b8489d..90a9b26abef4 100644
@@ -7,6 +7,7 @@ obj-$(CONFIG_ARCH_ASPEED) += sysreset_ast.o
 obj-$(CONFIG_ARCH_ROCKCHIP) += sysreset_rockchip.o
 obj-$(CONFIG_ARCH_STI) += sysreset_sti.o
 obj-$(CONFIG_SANDBOX) += sysreset_sandbox.o
+obj-$(CONFIG_POWEROFF_GPIO) += poweroff_gpio.o
 obj-$(CONFIG_SYSRESET_GPIO) += sysreset_gpio.o
 obj-$(CONFIG_SYSRESET_MPC83XX) += sysreset_mpc83xx.o
 obj-$(CONFIG_SYSRESET_MICROBLAZE) += sysreset_microblaze.o
drivers/sysreset/poweroff_gpio.c new file +92 -0

92 lines not on this page · raw message

Signature · 1 line
2.28.0
#10 lore raw

PATCH v4 5/9 sysreset: Add poweroff-gpio driver

Quoted 4 lines

Add GPIO poweroff driver, which is based on the Linux driver and uses the same DT binding.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#11 lore raw

PATCH v4 6/9 board: ge: common: rename ge_common.c to ge_rtc.c

In reply to Sebastian Reichel

The file only contains RTC related code, so let's name it accordingly.

---
 board/ge/bx50v3/bx50v3.c                  | 2 +-
 board/ge/common/Makefile                  | 2 +-
 board/ge/common/{ge_common.c => ge_rtc.c} | 0
 board/ge/common/{ge_common.h => ge_rtc.h} | 0
 board/ge/mx53ppd/mx53ppd.c                | 2 +-
 5 files changed, 3 insertions(+), 3 deletions(-)
 rename board/ge/common/{ge_common.c => ge_rtc.c} (100%)
 rename board/ge/common/{ge_common.h => ge_rtc.h} (100%)
board/ge/bx50v3/bx50v3.c +1 -1
index cf76cf7a3387..c6b0af8c776a 100644
@@ -35,7 +35,7 @@
 #include <version.h>
 #include <stdlib.h>
 #include <dm/root.h>
-#include "../common/ge_common.h"
+#include "../common/ge_rtc.h"
 #include "../common/vpd_reader.h"
 #include "../../../drivers/net/e1000.h"
 #include <pci.h>
board/ge/common/Makefile +1 -1
index 8a21dcb8b533..36bedb198077 100644
@@ -2,4 +2,4 @@
 #
 # Copyright 2017 General Electric Company
 
-obj-y  := vpd_reader.o ge_common.o
+obj-y  := vpd_reader.o ge_rtc.o
board/ge/common/ge_rtc.c renamed from board/ge/common/ge_common.c +0 -0
similarity index 100%
rename from board/ge/common/ge_common.c
rename to board/ge/common/ge_rtc.c
board/ge/common/ge_rtc.h renamed from board/ge/common/ge_common.h +0 -0
similarity index 100%
rename from board/ge/common/ge_common.h
rename to board/ge/common/ge_rtc.h
board/ge/mx53ppd/mx53ppd.c +1 -1
index 7627e9c370fb..2e9d389850a2 100644
@@ -36,7 +36,7 @@
 #include <watchdog.h>
 #include "ppd_gpio.h"
 #include <stdlib.h>
-#include "../../ge/common/ge_common.h"
+#include "../../ge/common/ge_rtc.h"
 #include "../../ge/common/vpd_reader.h"
 
 DECLARE_GLOBAL_DATA_PTR;
Signature · 1 line
2.28.0
#12 lore raw

PATCH v4 6/9 board: ge: common: rename ge_common.c to ge_rtc.c

Quoted 3 lines

The file only contains RTC related code, so let's name it accordingly.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#13 lore raw

PATCH v4 7/9 board: ge: common: add config option for RTC and VPD feature

In reply to Sebastian Reichel

While this code is being used by all GE platforms its useful to have it behind a config option for hardware bringup of new platforms.

---
 board/ge/bx50v3/Kconfig  | 2 ++
 board/ge/common/Kconfig  | 7 +++++++
 board/ge/common/Makefile | 3 ++-
 board/ge/mx53ppd/Kconfig | 2 ++
 4 files changed, 13 insertions(+), 1 deletion(-)
 create mode 100644 board/ge/common/Kconfig
board/ge/bx50v3/Kconfig +2 -0
index 993b0559302b..05938560abda 100644
@@ -15,4 +15,6 @@ config SYS_SOC
 config SYS_CONFIG_NAME
 	default "ge_bx50v3"
 
+source "board/ge/common/Kconfig"
+
 endif
board/ge/common/Kconfig new file +7 -0
new file mode 100644
index 000000000000..323ed1f99607
@@ -0,0 +1,7 @@
+config GE_VPD
+	bool "Enable GE VPD Support"
+	default y
+
+config GE_RTC
+	bool "Enable GE RTC Support"
+	default y
board/ge/common/Makefile +2 -1
index 36bedb198077..8bd44e3c8a0f 100644
@@ -2,4 +2,5 @@
 #
 # Copyright 2017 General Electric Company
 
-obj-y  := vpd_reader.o ge_rtc.o
+obj-$(CONFIG_GE_VPD)  += vpd_reader.o
+obj-$(CONFIG_GE_RTC)  += ge_rtc.o
board/ge/mx53ppd/Kconfig +2 -0
index 6dc3818cb7bb..bebb2fab0173 100644
@@ -13,4 +13,6 @@ config SYS_SOC
 config SYS_CONFIG_NAME
 	default "mx53ppd"
 
+source "board/ge/common/Kconfig"
+
 endif
Signature · 1 line
2.28.0
#14 lore raw

PATCH v4 7/9 board: ge: common: add config option for RTC and VPD feature

Quoted 4 lines

While this code is being used by all GE platforms its useful to have it behind a config option for hardware bringup of new platforms.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#15 lore raw

PATCH v4 8/9 board: ge: common: vpd: separate I2C specific code

In reply to Sebastian Reichel

This separates the I2C specific code from the generic GE vital product data code, so that the generic parts can be used on hardware with VPD stored in SPI flash memory.

---
 board/ge/bx50v3/bx50v3.c     |  2 +-
 board/ge/common/vpd_reader.c | 12 ++++++------
 board/ge/common/vpd_reader.h | 23 +++++++++++++++++++----
 board/ge/mx53ppd/mx53ppd.c   |  2 +-
 4 files changed, 27 insertions(+), 12 deletions(-)
board/ge/bx50v3/bx50v3.c +1 -1
index c6b0af8c776a..8a38ac5d4e4c 100644
@@ -429,7 +429,7 @@ static void set_confidx(const struct vpd_cache* vpd)
 
 int board_init(void)
 {
-	if (!read_vpd(&vpd, vpd_callback)) {
+	if (!read_i2c_vpd(&vpd, vpd_callback)) {
 		int ret, rescan;
 
 		vpd.is_read = true;
board/ge/common/vpd_reader.c +6 -6
index d42b00da2fe6..421fee592291 100644
@@ -110,9 +110,9 @@ static const size_t HEADER_BLOCK_ECC_LEN = 4;
 
 static const u8 ECC_BLOCK_ID = 0xFF;
 
-static int vpd_reader(size_t size, u8 *data, struct vpd_cache *userdata,
-		      int (*fn)(struct vpd_cache *, u8 id, u8 version, u8 type,
-				size_t size, u8 const *data))
+int vpd_reader(size_t size, u8 *data, struct vpd_cache *userdata,
+	       int (*fn)(struct vpd_cache *, u8 id, u8 version, u8 type,
+			 size_t size, u8 const *data))
 {
 	if (size < HEADER_BLOCK_LEN || !data || !fn)
 		return -EINVAL;
@@ -200,9 +200,9 @@ static int vpd_reader(size_t size, u8 *data, struct vpd_cache *userdata,
 	}
 }
 
-int read_vpd(struct vpd_cache *cache,
-	     int (*process_block)(struct vpd_cache *, u8 id, u8 version,
-				  u8 type, size_t size, u8 const *data))
+int read_i2c_vpd(struct vpd_cache *cache,
+		 int (*process_block)(struct vpd_cache *, u8 id, u8 version,
+				      u8 type, size_t size, u8 const *data))
 {
 	struct udevice *dev;
 	int ret;
board/ge/common/vpd_reader.h +19 -4
index 3045b7e21e22..0c51dc57e902 100644
@@ -16,7 +16,22 @@ struct vpd_cache;
  *
  * Returns Non-zero on error.  Negative numbers encode errno.
  */
-int read_vpd(struct vpd_cache *cache,
-	     int (*process_block)(struct vpd_cache *,
-				  u8 id, u8 version, u8 type,
-				  size_t size, u8 const *data));
+int read_i2c_vpd(struct vpd_cache *cache,
+		 int (*process_block)(struct vpd_cache *, u8 id, u8 version,
+				      u8 type, size_t size, u8 const *data));
+
+/*
+ * Read VPD from given data, verify content, call callback for each vital
+ * product data block.
+ *
+ * size: size of the raw VPD data in bytes
+ * data: raw VPD data read from device
+ * cache: structure used by process block to store VPD information
+ * process_block: callback called for each VPD data block
+ *
+ * Returns Non-zero on error.  Negative numbers encode errno.
+ */
+
+int vpd_reader(size_t size, u8 *data, struct vpd_cache *cache,
+	       int (*process_block)(struct vpd_cache *, u8 id, u8 version, u8 type,
+				    size_t size, u8 const *data));
board/ge/mx53ppd/mx53ppd.c +1 -1
index 2e9d389850a2..ef689733c41d 100644
@@ -225,7 +225,7 @@ int board_late_init(void)
 	struct vpd_cache vpd;
 
 	memset(&vpd, 0, sizeof(vpd));
-	res = read_vpd(&vpd, vpd_callback);
+	res = read_i2c_vpd(&vpd, vpd_callback);
 	if (!res)
 		process_vpd(&vpd);
 	else
Signature · 1 line
2.28.0
#16 lore raw

PATCH v4 8/9 board: ge: common: vpd: separate I2C specific code

Quoted 5 lines

This separates the I2C specific code from the generic GE vital product data code, so that the generic parts can be used on hardware with VPD stored in SPI flash memory.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#17 lore raw

PATCH v4 9/9 board: ge: b1x5v2: Add GE B1x5v2 and B1x5Pv2

In reply to Sebastian Reichel

GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor series (GE Bx50). It consists of a carrier PCB used in combination with a Congatec QMX6 SoM. This adds U-Boot support using device model everywhere and SPL for memory initialization.

Proper configuration is provided as 'ge_b1x5v2_defconfig' and the combined image u-boot-with-spi.imx can be flashed directly to 1024 byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can be loaded separately via USB-OTG using e.g. imx_usb.

---
 arch/arm/dts/Makefile          |   1 +
 arch/arm/dts/imx6dl-b1x5v2.dts | 654 ++++++++++++++++++++++++++++++
 arch/arm/mach-imx/mx6/Kconfig  |   9 +
 board/ge/b1x5v2/Kconfig        |  14 +
 board/ge/b1x5v2/Makefile       |   6 +
 board/ge/b1x5v2/b1x5v2.c       | 698 +++++++++++++++++++++++++++++++++
 board/ge/b1x5v2/spl.c          | 587 +++++++++++++++++++++++++++
 configs/ge_b1x5v2_defconfig    | 137 +++++++
 include/configs/ge_b1x5v2.h    | 127 ++++++
 9 files changed, 2233 insertions(+)
 create mode 100644 arch/arm/dts/imx6dl-b1x5v2.dts
 create mode 100644 board/ge/b1x5v2/Kconfig
 create mode 100644 board/ge/b1x5v2/Makefile
 create mode 100644 board/ge/b1x5v2/b1x5v2.c
 create mode 100644 board/ge/b1x5v2/spl.c
 create mode 100644 configs/ge_b1x5v2_defconfig
 create mode 100644 include/configs/ge_b1x5v2.h
arch/arm/dts/Makefile +1 -0
index f8f529435bf1..db0b2bdaf505 100644
@@ -975,6 +975,7 @@ dtb-$(CONFIG_TARGET_GE_BX50V3) += \
 	imx6q-b650v3.dtb \
 	imx6q-b450v3.dtb
 
+dtb-$(CONFIG_TARGET_GE_B1X5V2) += imx6dl-b1x5v2.dtb
 dtb-$(CONFIG_TARGET_MX53PPD) += imx53-ppd.dtb
 
 dtb-$(CONFIG_TARGET_VEXPRESS_CA5X2) += vexpress-v2p-ca5s.dtb
arch/arm/dts/imx6dl-b1x5v2.dts new file +654 -0

654 lines not on this page · raw message

arch/arm/mach-imx/mx6/Kconfig +9 -0
index 3d72517fa1df..0646b7369c2d 100644
@@ -253,6 +253,14 @@ config TARGET_GE_BX50V3
 	depends on MX6Q
 	select BOARD_LATE_INIT
 
+config TARGET_GE_B1X5V2
+	bool "General Electric B1x5v2"
+	depends on MX6QDL
+	select BOARD_LATE_INIT
+	select DM
+	select DM_THERMAL
+	select SUPPORT_SPL
+
 config TARGET_GW_VENTANA
 	bool "gw_ventana"
 	depends on MX6QDL
@@ -713,6 +721,7 @@ config SYS_SOC
 	default "mx6"
 
 source "board/ge/bx50v3/Kconfig"
+source "board/ge/b1x5v2/Kconfig"
 source "board/advantech/dms-ba16/Kconfig"
 source "board/aristainetos/Kconfig"
 source "board/armadeus/opos6uldev/Kconfig"
board/ge/b1x5v2/Kconfig new file +14 -0
new file mode 100644
index 000000000000..80a5bcae7dee
@@ -0,0 +1,14 @@
+if TARGET_GE_B1X5V2
+
+config SYS_BOARD
+	default "b1x5v2"
+
+config SYS_VENDOR
+	default "ge"
+
+config SYS_CONFIG_NAME
+	default "ge_b1x5v2"
+
+source "board/ge/common/Kconfig"
+
+endif
board/ge/b1x5v2/Makefile new file +6 -0
new file mode 100644
index 000000000000..8a27af52e1ae
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright 2018-2020 Collabora
+# Copyright 2018-2020 GE
+
+obj-y :=  b1x5v2.o spl.o
board/ge/b1x5v2/b1x5v2.c new file +698 -0

698 lines not on this page · raw message

board/ge/b1x5v2/spl.c new file +587 -0

587 lines not on this page · raw message

configs/ge_b1x5v2_defconfig new file +137 -0

137 lines not on this page · raw message

include/configs/ge_b1x5v2.h new file +127 -0

127 lines not on this page · raw message

Signature · 1 line
2.28.0
#18 lore raw

PATCH v4 9/9 board: ge: b1x5v2: Add GE B1x5v2 and B1x5Pv2

Quoted 11 lines · Sebastian Reichel

GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor series (GE Bx50). It consists of a carrier PCB used in combination with a Congatec QMX6 SoM. This adds U-Boot support using device model everywhere and SPL for memory initialization.

Proper configuration is provided as 'ge_b1x5v2_defconfig' and the combined image u-boot-with-spi.imx can be flashed directly to 1024 byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can be loaded separately via USB-OTG using e.g. imx_usb.

As I went checking for a good sized gap between kernel and dtb, and I see it's got I was looking for:

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20200902/cf6bec7b/attachment.sig>
#19 lore raw

PATCH v4 9/9 board: ge: b1x5v2: Add GE B1x5v2 and B1x5Pv2

In reply to Sebastian Reichel
Quoted 10 lines

GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor series (GE Bx50). It consists of a carrier PCB used in combination with a Congatec QMX6 SoM. This adds U-Boot support using device model everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the combined image u-boot-with-spi.imx can be flashed directly to 1024 byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can be loaded separately via USB-OTG using e.g. imx_usb.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
reviewer
#20 lore raw

v4 cover Introduce B1x5v2 support

In reply to Sebastian Reichel

Hi Sebastian,

Quoted 11 lines · Sebastian Reichel

This series introduces support for a new i.MX6DL based GE patient monitor series.

Patch 1: Add support for storing bootcount in SPI-flash Patch 2+3: Improve M41T62 RTC driver's reset routine. PATCH 4: Support disable_ldb_di_clock_sources for i.MX6DL Patch 5: Add poweroff-gpio support
Patch 6-8: restructure common GE code
Patch 9: Add the actual board, using SPL and DM

Quoted 4 lines

Changes since PATCHv3 [0]:
* Dropped patch for reading DR for i.MX GPIOs and set SION pinmux bits in B1x5v2 output GPIOs instead
* Rebased to v2020.10-rc3

Thanks for the respin. This version looks good:

#21 lore raw

v4 cover Introduce B1x5v2 support

In reply to Sebastian Reichel

Hi Sebastian,

I integrated the patches but the MAINTAINERS file for B1x5v2 is missing. Can you send a follow-up patch to fix this ? (Or just a V5 for 9/9, your choice).

Regards,
Stefano

Quoted 88 lines · Sebastian Reichel

This series introduces support for a new i.MX6DL based GE patient monitor series.

Patch 1: Add support for storing bootcount in SPI-flash Patch 2+3: Improve M41T62 RTC driver's reset routine. PATCH 4: Support disable_ldb_di_clock_sources for i.MX6DL Patch 5: Add poweroff-gpio support
Patch 6-8: restructure common GE code
Patch 9: Add the actual board, using SPL and DM

Changes since PATCHv3 [0]:
* Dropped patch for reading DR for i.MX GPIOs and set SION pinmux bits in B1x5v2 output GPIOs instead
* Rebased to v2020.10-rc3

Changes since PATCHv2:

* PATCH 10: Fixed network phy mode ("rgmii" -> "rgmii-id")
* PATCH 6: Fixed nits reported by Simon Glass and added is Reviewed-by Tag.

Changes since PATCHv1:

* Rebased to v2020.10-rc2
* Original patch 1 (support for DM_SPI_FLASH with non-DM SPL) has been dropped, since a similar patch has been merged in the meantime
* poweroff-gpio support is now added using sysreset uclass instead of introducing a new poweroff uclass
* B1x5v2 patch has been updated to follow recent U-Boot changes and to add USB mass storage support

[0] http://patchwork.ozlabs.org/project/uboot/list/?series=196979

-- Sebastian

Sebastian Reichel (9):
bootcount: add a DM SPI flash backing store for bootcount
rtc: m41t62: reset SQW in m41t62_rtc_reset
rtc: m41t62: add oscillator fail bit reset support
imx6: allow usage of disable_ldb_di_clock_sources for CONFIG_MX6QDL
sysreset: Add poweroff-gpio driver
board: ge: common: rename ge_common.c to ge_rtc.c
board: ge: common: add config option for RTC and VPD feature
board: ge: common: vpd: separate I2C specific code
board: ge: b1x5v2: Add GE B1x5v2 and B1x5Pv2

  arch/arm/dts/Makefile                     |   1 +
  arch/arm/dts/imx6dl-b1x5v2.dts            | 654 ++++++++++++++++++++
  arch/arm/mach-imx/mx6/Kconfig             |   9 +
  arch/arm/mach-imx/mx6/clock.c             |   2 +-
  board/ge/b1x5v2/Kconfig                   |  14 +
  board/ge/b1x5v2/Makefile                  |   6 +
  board/ge/b1x5v2/b1x5v2.c                  | 698 ++++++++++++++++++++++
  board/ge/b1x5v2/spl.c                     | 587 ++++++++++++++++++
  board/ge/bx50v3/Kconfig                   |   2 +
  board/ge/bx50v3/bx50v3.c                  |   4 +-
  board/ge/common/Kconfig                   |   7 +
  board/ge/common/Makefile                  |   3 +-
  board/ge/common/{ge_common.c => ge_rtc.c} |   0
  board/ge/common/{ge_common.h => ge_rtc.h} |   0
  board/ge/common/vpd_reader.c              |  12 +-
  board/ge/common/vpd_reader.h              |  23 +-
  board/ge/mx53ppd/Kconfig                  |   2 +
  board/ge/mx53ppd/mx53ppd.c                |   4 +-
  configs/ge_b1x5v2_defconfig               | 137 +++++
  drivers/bootcount/Kconfig                 |  10 +
  drivers/bootcount/Makefile                |   1 +
  drivers/bootcount/spi-flash.c             | 125 ++++
  drivers/rtc/m41t62.c                      | 139 ++++-
  drivers/sysreset/Kconfig                  |   7 +
  drivers/sysreset/Makefile                 |   1 +
  drivers/sysreset/poweroff_gpio.c          |  92 +++
  include/configs/ge_b1x5v2.h               | 127 ++++
  27 files changed, 2645 insertions(+), 22 deletions(-)

create mode 100644 arch/arm/dts/imx6dl-b1x5v2.dts create mode 100644 board/ge/b1x5v2/Kconfig create mode 100644 board/ge/b1x5v2/Makefile create mode 100644 board/ge/b1x5v2/b1x5v2.c create mode 100644 board/ge/b1x5v2/spl.c create mode 100644 board/ge/common/Kconfig rename board/ge/common/{ge_common.c => ge_rtc.c} (100%) rename board/ge/common/{ge_common.h => ge_rtc.h} (100%) create mode 100644 configs/ge_b1x5v2_defconfig create mode 100644 drivers/bootcount/spi-flash.c create mode 100644 drivers/sysreset/poweroff_gpio.c create mode 100644 include/configs/ge_b1x5v2.h

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#22 lore raw

v4 cover Introduce B1x5v2 support

Hi Sebastian,

Quoted 5 lines · Stefano Babic

Hi Sebastian,

I integrated the patches but the MAINTAINERS file for B1x5v2 is missing. Can you send a follow-up patch to fix this ? (Or just a V5 for 9/9, your choice).

Just send a follow-up patch, thanks.

Regards,
Stefano

Quoted 94 lines

Regards,
Stefano

Quoted 88 lines · Sebastian Reichel

This series introduces support for a new i.MX6DL based GE patient monitor series.

Patch 1: Add support for storing bootcount in SPI-flash Patch 2+3: Improve M41T62 RTC driver's reset routine. PATCH 4: Support disable_ldb_di_clock_sources for i.MX6DL Patch 5: Add poweroff-gpio support
Patch 6-8: restructure common GE code
Patch 9: Add the actual board, using SPL and DM

Changes since PATCHv3 [0]:
? * Dropped patch for reading DR for i.MX GPIOs and set ??? SION pinmux bits in B1x5v2 output GPIOs instead ? * Rebased to v2020.10-rc3

Changes since PATCHv2:

* PATCH 10: Fixed network phy mode ("rgmii" -> "rgmii-id")
* PATCH 6: Fixed nits reported by Simon Glass and added is ?? Reviewed-by Tag.

Changes since PATCHv1:

* Rebased to v2020.10-rc2
* Original patch 1 (support for DM_SPI_FLASH with non-DM SPL) ?? has been dropped, since a similar patch has been merged ?? in the meantime
* poweroff-gpio support is now added using sysreset uclass ?? instead of introducing a new poweroff uclass
* B1x5v2 patch has been updated to follow recent U-Boot ?? changes and to add USB mass storage support

[0] http://patchwork.ozlabs.org/project/uboot/list/?series=196979

-- Sebastian

Sebastian Reichel (9):
?? bootcount: add a DM SPI flash backing store for bootcount ?? rtc: m41t62: reset SQW in m41t62_rtc_reset
?? rtc: m41t62: add oscillator fail bit reset support
?? imx6: allow usage of disable_ldb_di_clock_sources for CONFIG_MX6QDL ?? sysreset: Add poweroff-gpio driver
?? board: ge: common: rename ge_common.c to ge_rtc.c
?? board: ge: common: add config option for RTC and VPD feature ?? board: ge: common: vpd: separate I2C specific code
?? board: ge: b1x5v2: Add GE B1x5v2 and B1x5Pv2

? arch/arm/dts/Makefile???????????????????? |?? 1 +
? arch/arm/dts/imx6dl-b1x5v2.dts??????????? | 654 ++++++++++++++++++++
? arch/arm/mach-imx/mx6/Kconfig???????????? |?? 9 +
? arch/arm/mach-imx/mx6/clock.c???????????? |?? 2 +-
? board/ge/b1x5v2/Kconfig?????????????????? |? 14 +
? board/ge/b1x5v2/Makefile????????????????? |?? 6 +
? board/ge/b1x5v2/b1x5v2.c????????????????? | 698 ++++++++++++++++++++++
? board/ge/b1x5v2/spl.c???????????????????? | 587 ++++++++++++++++++
? board/ge/bx50v3/Kconfig?????????????????? |?? 2 +
? board/ge/bx50v3/bx50v3.c????????????????? |?? 4 +-
? board/ge/common/Kconfig?????????????????? |?? 7 +
? board/ge/common/Makefile????????????????? |?? 3 +-
? board/ge/common/{ge_common.c => ge_rtc.c} |?? 0
? board/ge/common/{ge_common.h => ge_rtc.h} |?? 0
? board/ge/common/vpd_reader.c????????????? |? 12 +-
? board/ge/common/vpd_reader.h????????????? |? 23 +-
? board/ge/mx53ppd/Kconfig????????????????? |?? 2 +
? board/ge/mx53ppd/mx53ppd.c??????????????? |?? 4 +-
? configs/ge_b1x5v2_defconfig?????????????? | 137 +++++
? drivers/bootcount/Kconfig???????????????? |? 10 +
? drivers/bootcount/Makefile??????????????? |?? 1 +
? drivers/bootcount/spi-flash.c???????????? | 125 ++++
? drivers/rtc/m41t62.c????????????????????? | 139 ++++-
? drivers/sysreset/Kconfig????????????????? |?? 7 +
? drivers/sysreset/Makefile???????????????? |?? 1 +
? drivers/sysreset/poweroff_gpio.c????????? |? 92 +++
? include/configs/ge_b1x5v2.h?????????????? | 127 ++++

? 27 files changed, 2645 insertions(+), 22 deletions(-) ? create mode 100644 arch/arm/dts/imx6dl-b1x5v2.dts ? create mode 100644 board/ge/b1x5v2/Kconfig
? create mode 100644 board/ge/b1x5v2/Makefile
? create mode 100644 board/ge/b1x5v2/b1x5v2.c
? create mode 100644 board/ge/b1x5v2/spl.c
? create mode 100644 board/ge/common/Kconfig
? rename board/ge/common/{ge_common.c => ge_rtc.c} (100%) ? rename board/ge/common/{ge_common.h => ge_rtc.h} (100%) ? create mode 100644 configs/ge_b1x5v2_defconfig ? create mode 100644 drivers/bootcount/spi-flash.c ? create mode 100644 drivers/sysreset/poweroff_gpio.c ? create mode 100644 include/configs/ge_b1x5v2.h

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================