arm64: dts: ti: k3-j7200: add dma and mcu cpsw
Subsystems (2)
v4 cover arm64: dts: ti: k3-j7200: add dma and mcu cpsw
Hi All,
This series adds DT nodes for TI J7200 SoC
- Ringacc and UDMA nodes for Main and MCU NAVSS, which are compatible with J721E Soc, to enable DMA support
- MCU CPSW2g DT nodes to enable networking and board data
Changes in v4:
- fixed comments from Suman Anna <[email protected]>
Changes in v3:
- rebase
- updated dependencies
- added tested-by
Changes in v2:
- fixed DT build warnings (Nishanth Menon)
v3: https://lore.kernel.org/patchwork/cover/1308044/
v2: https://lore.kernel.org/patchwork/cover/1302290/
v1: https://lore.kernel.org/patchwork/cover/1301067/
Grygorii Strashko (3):
arm64: dts: ti: k3-j7200-main: add main navss cpts node
arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux
and phy defs
Peter Ujfalusi (1):
arm64: dts: ti: k3-j7200: add DMA support
.../dts/ti/k3-j7200-common-proc-board.dts | 45 +++++++ arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 48 +++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 118 ++++++++++++++++++ 3 files changed, 211 insertions(+)
Signature · 1 line
2.17.1
PATCH v4 1/4 arm64: dts: ti: k3-j7200: add DMA support
From: Peter Ujfalusi <[email protected]>
Add the ringacc and udmap nodes for Main and MCU NAVSS.
--- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 36 +++++++++++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 44 +++++++++++++++++++ 2 files changed, 80 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +36 -0
@@ -93,6 +93,42 @@ interrupt-names = "rx_011"; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; }; + + main_ringacc: ringacc@3c000000 { + compatible = "ti,am654-navss-ringacc"; + reg = <0x00 0x3c000000 0x00 0x400000>, + <0x00 0x38000000 0x00 0x400000>, + <0x00 0x31120000 0x00 0x100>, + <0x00 0x33000000 0x00 0x40000>; + reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target"; + ti,num-rings = <1024>; + ti,sci-rm-range-gp-rings = <0x1>; /* GP ring range */ + ti,sci = <&dmsc>; + ti,sci-dev-id = <211>; + msi-parent = <&main_udmass_inta>; + }; + + main_udmap: dma-controller@31150000 { + compatible = "ti,j721e-navss-main-udmap"; + reg = <0x00 0x31150000 0x00 0x100>, + <0x00 0x34000000 0x00 0x100000>, + <0x00 0x35000000 0x00 0x100000>; + reg-names = "gcfg", "rchanrt", "tchanrt"; + msi-parent = <&main_udmass_inta>; + #dma-cells = <1>; + + ti,sci = <&dmsc>; + ti,sci-dev-id = <212>; + ti,ringacc = <&main_ringacc>; + + ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */ + <0x0f>, /* TX_HCHAN */ + <0x10>; /* TX_UHCHAN */ + ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */ + <0x0b>, /* RX_HCHAN */ + <0x0c>; /* RX_UHCHAN */ + ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */ + }; }; main_pmx0: pinctrl@11c000 {
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +44 -0
48 lines not on this page · raw message
Signature · 1 line
2.17.1
PATCH v4 2/4 arm64: dts: ti: k3-j7200-main: add main navss cpts node
In reply to Grygorii StrashkoAdd DT node for Main NAVSS CPTS module.
--- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +12 -0
@@ -129,6 +129,18 @@ <0x0c>; /* RX_UHCHAN */ ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */ }; + + cpts@310d0000 { + compatible = "ti,j721e-cpts"; + reg = <0x00 0x310d0000 0x00 0x400>; + reg-names = "cpts"; + clocks = <&k3_clks 201 1>; + clock-names = "cpts"; + interrupts-extended = <&main_navss_intr 391>; + interrupt-names = "cpts"; + ti,cpts-periodic-outputs = <6>; + ti,cpts-ext-ts-inputs = <8>; + }; }; main_pmx0: pinctrl@11c000 {
Signature · 1 line
2.17.1
PATCH v4 3/4 arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
In reply to Grygorii StrashkoAdd DT node for The TI J7200 MCU SoC Gigabit Ethernet two ports Switch subsystem (MCU CPSW NUSS).
--- .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 74 +++++++++++++++++++ 1 file changed, 74 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +74 -0
@@ -34,6 +34,20 @@ }; }; + mcu_conf: syscon@40f00000 { + compatible = "syscon", "simple-mfd"; + reg = <0x00 0x40f00000 0x00 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x00 0x40f00000 0x20000>; + + phy_gmii_sel: phy@4040 { + compatible = "ti,am654-phy-gmii-sel"; + reg = <0x4040 0x4>; + #phy-cells = <1>; + }; + }; + chipid@43000014 { compatible = "ti,am654-chipid"; reg = <0x00 0x43000014 0x00 0x4>;
@@ -136,4 +150,64 @@ ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */ }; }; + + mcu_cpsw: ethernet@46000000 { + compatible = "ti,j721e-cpsw-nuss"; + #address-cells = <2>; + #size-cells = <2>; + reg = <0x00 0x46000000 0x00 0x200000>; + reg-names = "cpsw_nuss"; + ranges = <0x00 0x00 0x00 0x46000000 0x00 0x200000>; + dma-coherent; + clocks = <&k3_clks 18 21>; + clock-names = "fck"; + power-domains = <&k3_pds 18 TI_SCI_PD_EXCLUSIVE>; + + dmas = <&mcu_udmap 0xf000>, + <&mcu_udmap 0xf001>, + <&mcu_udmap 0xf002>, + <&mcu_udmap 0xf003>, + <&mcu_udmap 0xf004>, + <&mcu_udmap 0xf005>, + <&mcu_udmap 0xf006>, + <&mcu_udmap 0xf007>, + <&mcu_udmap 0x7000>; + dma-names = "tx0", "tx1", "tx2", "tx3", + "tx4", "tx5", "tx6", "tx7", + "rx"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port@1 { + reg = <1>; + ti,mac-only; + label = "port1"; + ti,syscon-efuse = <&mcu_conf 0x200>; + phys = <&phy_gmii_sel 1>; + }; + }; + + davinci_mdio: mdio@f00 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + reg = <0x00 0xf00 0x00 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&k3_clks 18 21>; + clock-names = "fck"; + bus_freq = <1000000>; + }; + + cpts@3d000 { + compatible = "ti,am65-cpts"; + reg = <0x00 0x3d000 0x00 0x400>; + clocks = <&k3_clks 18 2>; + clock-names = "cpts"; + interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cpts"; + ti,cpts-ext-ts-inputs = <4>; + ti,cpts-periodic-outputs = <2>; + }; + }; };
Signature · 1 line
2.17.1
PATCH v4 4/4 arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux and phy defs
In reply to Grygorii StrashkoThe TI j7200 EVM base board has TI DP83867 PHY connected to external CPSW NUSS Port 1 in rgmii-rxid mode.
Hence, add pinmux and Ethernet PHY configuration for TI j7200 SoC MCU Gigabit Ethernet two ports Switch subsystem (CPSW NUSS).
--- .../dts/ti/k3-j7200-common-proc-board.dts | 45 +++++++++++++++++++ 1 file changed, 45 insertions(+)
arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +45 -0
@@ -6,6 +6,7 @@ /dts-v1/; #include "k3-j7200-som-p0.dtsi" +#include <dt-bindings/net/ti-dp83867.h> / { chosen {
@@ -14,6 +15,32 @@ }; }; +&wkup_pmx0 { + mcu_cpsw_pins_default: mcu-cpsw-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */ + J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */ + J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */ + J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */ + J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */ + J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */ + J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */ + J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */ + J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */ + J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */ + J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_TXC */ + J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */ + >; + }; + + mcu_mdio_pins_default: mcu-mdio1-pins-default { + pinctrl-single,pins = < + J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */ + J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */ + >; + }; +}; + &wkup_uart0 { /* Wakeup UART is used by System firmware */ status = "disabled";
@@ -63,3 +90,21 @@ /* UART not brought out */ status = "disabled"; }; + +&mcu_cpsw { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>; +}; + +&davinci_mdio { + phy0: ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; +}; + +&cpsw_port1 { + phy-mode = "rgmii-rxid"; + phy-handle = <&phy0>; +};
Signature · 1 line
2.17.1
Quoted 22 lines · Grygorii Strashko
Hi All,
This series adds DT nodes for TI J7200 SoC
- Ringacc and UDMA nodes for Main and MCU NAVSS, which are compatible with J721E Soc, to enable DMA support
- MCU CPSW2g DT nodes to enable networking and board dataChanges in v4:
- fixed comments from Suman Anna <[email protected]>Changes in v3:
- rebase
- updated dependencies
- added tested-byChanges in v2:
- fixed DT build warnings (Nishanth Menon)v3: https://lore.kernel.org/patchwork/cover/1308044/
v2: https://lore.kernel.org/patchwork/cover/1302290/
v1: https://lore.kernel.org/patchwork/cover/1301067/
Quoted 8 lines
Grygorii Strashko (3):
arm64: dts: ti: k3-j7200-main: add main navss cpts node
arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux
and phy defsPeter Ujfalusi (1):
arm64: dts: ti: k3-j7200: add DMA support
Thank you for fixing my comments. For the series,
regards
Suman
Quoted 6 lines
.../dts/ti/k3-j7200-common-proc-board.dts | 45 +++++++ arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 48 +++++++ .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 118 ++++++++++++++++++ 3 files changed, 211 insertions(+)
Quoted 9 lines · Grygorii Strashko
This series adds DT nodes for TI J7200 SoC
- Ringacc and UDMA nodes for Main and MCU NAVSS, which are compatible with J721E Soc, to enable DMA support
- MCU CPSW2g DT nodes to enable networking and board dataChanges in v4:
- fixed comments from Suman Anna <[email protected]>[...]
Hi Grygorii Strashko,
I have applied the following to branch ti-k3-dts-next on [1]. Thank you!
[1/4] arm64: dts: ti: k3-j7200: add DMA support
commit: fd409bfe0e44ea36ed6be77c331a001e50a9bc12
[2/4] arm64: dts: ti: k3-j7200-main: add main navss cpts node
commit: 3273476c3b1c7ef61ec971ed866b9fb6660c82fe
[3/4] arm64: dts: ti: k3-j7200-mcu: add mcu cpsw nuss node
commit: e86fc00bb04b1d3d387ae6bf4d176bfa9859ea66
[4/4] arm64: dts: ti: k3-j7200-common-proc-board: add mcu cpsw nuss pinmux and phy defs
commit: c67487a68e13ee450cbc45b622b8ee9a75f1812aAll being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent up the chain during the next merge window (or sooner if it is a relevant bug fix), however if problems are discovered then the patch may be dropped or reverted.
You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.
If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.
Please add any relevant lists and maintainers to the CCs when replying to this mail.
[1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D