Skip to contentSkip to conversation

board: imx: address dd usage in README

PATCH Superseded Peng Fan 2 participants 2 messages Oct 12, 2020 – Oct 13, 2020 Arm i.MX and Layerscape

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore

Peng Fan

author
#0 lore raw

PATCH 1/1 board: imx: address dd usage in README

When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)", the last not 512bytes aligned data wat cut off and not burned into SD card.

Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only burned 1085440 bytes, the leaving 168 bytes were not burnned and cause boot issue.

So update README dd command to add "conv=notrunc"

---
 board/freescale/imx8mm_evk/README      |  2 +-
 board/freescale/imx8mn_evk/README      |  2 +-
 board/freescale/imx8mp_evk/README      |  2 +-
 board/freescale/imx8mq_evk/README      |  2 +-
 board/freescale/imx8qxp_mek/README     |  2 +-
 board/freescale/imxrt1020-evk/README   |  4 ++--
 board/freescale/imxrt1050-evk/README   |  4 ++--
 board/freescale/mx6sabreauto/README    |  8 ++++----
 board/freescale/mx6sabresd/README      | 12 ++++++------
 board/freescale/mx6ul_14x14_evk/README |  4 ++--
 board/freescale/mx6ullevk/README       |  2 +-
 11 files changed, 22 insertions(+), 22 deletions(-)
board/freescale/imx8mm_evk/README +1 -1
index fa3f079f31..3307711d5d 100644
@@ -30,7 +30,7 @@ $ export ATF_LOAD_ADDR=0x920000
 $ make flash.bin
 
 Burn the flash.bin to MicroSD card offset 33KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33
+$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 conv=notrunc
 
 Boot
 ====
board/freescale/imx8mn_evk/README +1 -1
index ff3d15c02b..ec007afb25 100644
@@ -30,7 +30,7 @@ $ export ATF_LOAD_ADDR=0x960000
 $ make flash.bin
 
 Burn the flash.bin to MicroSD card offset 32KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
+$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 conv=notrunc
 
 Boot
 ====
board/freescale/imx8mp_evk/README +1 -1
index 7dd3a9352a..3c64979be9 100644
@@ -33,7 +33,7 @@ $ export ATF_LOAD_ADDR=0x960000
 $ make flash.bin
 
 Burn the flash.bin to the MicroSD card at offset 32KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32; sync
+$sudo dd if=flash.bin of=/dev/sd[x] bs=1K seek=32 conv=notrunc; sync
 
 Boot
 ====
board/freescale/imx8mq_evk/README +1 -1
index 859f852255..2689459b9f 100644
@@ -30,7 +30,7 @@ $ make imx8mq_evk_defconfig
 $ make flash.bin
 
 Burn the flash.bin to MicroSD card offset 33KB
-$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33
+$sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=33 conv=notrunc
 
 Boot
 ====
board/freescale/imx8qxp_mek/README +1 -1
index 6e4eb5996b..6f99d0e13e 100644
@@ -43,7 +43,7 @@ Flash the binary into the SD card
 
 Burn the flash.bin binary to SD card offset 32KB:
 
-$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32
+$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32 conv=notrunc
 
 Boot
 ====
board/freescale/imxrt1020-evk/README +2 -2
index abee7ca5f3..9bc5bc00bc 100644
@@ -11,11 +11,11 @@ This will generate the SPL image called SPL and the u-boot.img.
 
 - Flash the SPL image into the micro SD card:
 
-sudo dd if=SPL of=/dev/sdX bs=1k seek=1; sync
+sudo dd if=SPL of=/dev/sdX bs=1k seek=1 conv=notrunc; sync
 
 - Flash the u-boot.img image into the micro SD card:
 
-sudo dd if=u-boot.img of=/dev/sdX bs=1k seek=128; sync
+sudo dd if=u-boot.img of=/dev/sdX bs=1k seek=128 conv=notrunc; sync
 
 - Jumper settings:
 
board/freescale/imxrt1050-evk/README +2 -2
index a7e68fa9b3..f321300246 100644
@@ -11,11 +11,11 @@ This will generate the SPL image called SPL and the u-boot.img.
 
 - Flash the SPL image into the micro SD card:
 
-sudo dd if=SPL of=/dev/sdX bs=1k seek=1; sync
+sudo dd if=SPL of=/dev/sdX bs=1k seek=1 conv=notrunc; sync
 
 - Flash the u-boot.img image into the micro SD card:
 
-sudo dd if=u-boot.img of=/dev/sdX bs=1k seek=128; sync
+sudo dd if=u-boot.img of=/dev/sdX bs=1k seek=128 conv=notrunc; sync
 
 - Jumper settings:
 
board/freescale/mx6sabreauto/README +4 -4
index 4c0fda1a2d..710026a05e 100644
@@ -13,11 +13,11 @@ This will generate the SPL and u-boot-dtb.img binaries.
 
 - Flash the SPL binary into the SD card:
 
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
 
 - Flash the u-boot-dtb.img binary into the SD card:
 
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
 
 Booting via Falcon mode
 -----------------------
@@ -36,11 +36,11 @@ This will generate the SPL image called SPL and the u-boot-dtb.img.
 
 - Flash the SPL image into the SD card:
 
-$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 && sync
+$ sudo dd if=SPL of=/dev/sdb bs=1K seek=1 conv=notrunc && sync
 
 - Flash the u-boot-dtb.img image into the SD card:
 
-$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdb bs=1K seek=69 conv=notrunc && sync
 
 Create a FAT16 boot partition to store uImage and the dtb file, then copy the files there:
 
board/freescale/mx6sabresd/README +6 -6
index 4ea4454b9f..974b0be175 100644
@@ -25,11 +25,11 @@ This will generate the SPL and u-boot-dtb.img binaries.
 
 - Flash the SPL binary into the SD card:
 
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
 
 - Flash the u-boot-dtb.img binary into the SD card:
 
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
 
 
 2. Booting from eMMC
@@ -53,8 +53,8 @@ Mount the eMMC in the host PC:
 
 - Flash SPL and u-boot-dtb.img binaries into the eMMC:
 
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 && sync
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 conv=notrunc && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 conv=notrunc && sync
 
 Set SW6 to eMMC 8-bit boot: 11010110
 
@@ -69,11 +69,11 @@ This will generate the SPL image called SPL and the u-boot-dtb.img.
 
 - Flash the SPL image into the SD card:
 
-$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none && sync
+$ sudo dd if=SPL of=/dev/sdX bs=1K seek=1 oflag=sync status=none conv=notrunc && sync
 
 - Flash the u-boot-dtb.img image into the SD card:
 
-$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none && sync
+$ sudo dd if=u-boot-dtb.img of=/dev/sdX bs=1K seek=69 oflag=sync status=none conv=notrunc && sync
 
 Create a partition for root file system and extract it there:
 
board/freescale/mx6ul_14x14_evk/README +2 -2
index e101abe48c..70eb86efba 100644
@@ -14,11 +14,11 @@ This will generate the SPL image called SPL and the u-boot.img.
 
 - Flash the SPL image into the micro SD card:
 
-sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1 conv=notrunc; sync
 
 - Flash the u-boot.img image into the micro SD card:
 
-sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69; sync
+sudo dd if=u-boot.img of=/dev/mmcblk0 bs=1k seek=69 conv=notrunc; sync
 
 - Jumper settings:
 
board/freescale/mx6ullevk/README +1 -1
index d5c8770863..47a35f61a2 100644
@@ -15,7 +15,7 @@ This generates the u-boot-dtb.imx image in the current directory.
 
 - Flash the u-boot-dtb.imx image into the micro SD card:
 
-$ sudo dd if=u-boot-dtb.imx of=/dev/sdb bs=1K seek=1 && sync
+$ sudo dd if=u-boot-dtb.imx of=/dev/sdb bs=1K seek=1 conv=notrunc && sync
 
 - Jumper settings:
 
Signature · 1 line
2.28.0
#1 lore raw

PATCH 1/1 board: imx: address dd usage in README

Quoted 11 lines · Peng Fan

When using cygwin64 "dd (coreutils) 8.26 Packaged by Cygwin (8.26-2)", the last not 512bytes aligned data wat cut off and not burned into SD card.

Saying the flash.bin size is 1085608 bytes, not 512bytes aligned. It only burned 1085440 bytes, the leaving 168 bytes were not burnned and cause boot issue.

So update README dd command to add "conv=notrunc"

Quoted 13 lines
---
 board/freescale/imx8mm_evk/README      |  2 +-
 board/freescale/imx8mn_evk/README      |  2 +-
 board/freescale/imx8mp_evk/README      |  2 +-
 board/freescale/imx8mq_evk/README      |  2 +-
 board/freescale/imx8qxp_mek/README     |  2 +-
 board/freescale/imxrt1020-evk/README   |  4 ++--
 board/freescale/imxrt1050-evk/README   |  4 ++--
 board/freescale/mx6sabreauto/README    |  8 ++++----
 board/freescale/mx6sabresd/README      | 12 ++++++------
 board/freescale/mx6ul_14x14_evk/README |  4 ++--
 board/freescale/mx6ullevk/README       |  2 +-
 11 files changed, 22 insertions(+), 22 deletions(-)

Migration of all of these to doc/board/... is somewhere on the TODO list, right? Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20201013/e9f2add1/attachment.sig>