mx6: peripheral clock from oscillator
Subsystems (3)
PATCH 1/1 mx6: peripheral clock from oscillator
In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator.
[1] Rev 2, 10/2019, ERR007805
--- arch/arm/mach-imx/mx6/soc.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)
arch/arm/mach-imx/mx6/soc.c +3 -1
@@ -26,6 +26,8 @@#include <imx_thermal.h> #include <mmc.h> +#define ERRATA_ERR007805 (is_mx6dl() || is_mx6solo() || is_mx6ull()) +struct scu_regs {u32 ctrl;u32 config;
@@ -469,7 +471,7 @@ int arch_cpu_init(void) }/* Set perclk to source from OSC 24MHz */ -if (is_mx6sl ()) +if (is_mx6sl () ||ERRATA_ERR007805 )setbits_le32 (&ccm->cscmr1,MXC_CCM_CSCMR1_PER_CLK_SEL_MASK );imx_wdog_disable_powerdown ();/* Disable PDE bit of WMCR register */
Signature · 1 line
2.17.1
Jorge Ramirez-Ortiz
PATCH 1/1 mx6: peripheral clock from oscillator
Quoted 24 lines · Jorge Ramirez-Ortiz
In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator.
[1] Rev 2, 10/2019, ERR007805
Signed-off-by Jorge Ramirez-Ortiz <[email protected]>--- arch/arm/mach-imx/mx6/soc.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-)arch/arm/mach-imx/mx6/soc.c +2
-0@@ -26,6 +26,8 @@#include <imx_thermal.h> #include <mmc.h> +#define ERRATA_ERR007805 (is_mx6dl() || is_mx6solo() || is_mx6ull()) +struct scu_regs {u32 ctrl;u32 config;
arch/arm/mach-imx/mx6/soc.c int arch_cpu_init(void)
Quoted 9 lines
arch/arm/mach-imx/mx6/soc.c +1
-2@@ -469,7 +471,7 @@ int arch_cpu_init(void) }/* Set perclk to source from OSC 24MHz */ -if (is_mx6sl ()) +if (is_mx6sl () ||ERRATA_ERR007805 )setbits_le32 (&ccm->cscmr1,MXC_CCM_CSCMR1_PER_CLK_SEL_MASK );imx_wdog_disable_powerdown ();/* Disable PDE bit of WMCR register */ --
all ok with this ?
Quoted 2 lines
2.17.1
Fabio Estevam
reviewerPATCH 1/1 mx6: peripheral clock from oscillator
In reply to Jorge Ramirez-OrtizQuoted 3 lines · Jorge Ramirez-Ortiz
In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator.
I would suggest adding the optee related motivation that you explained earlier here in the commit log too.
Quoted 1 line
[1] Rev 2, 10/2019, ERR007805
Not clear what document this refers to.
arch/arm/mach-imx/mx6/soc.c int arch_cpu_init(void) · line 474
Quoted 3 lines
/* Set perclk to source from OSC 24MHz */arch/arm/mach-imx/mx6/soc.c +1
-1-if (is_mx6sl ()) +if (is_mx6sl () ||ERRATA_ERR007805 )
This gives the impression that imx6sl is not affected by the erratum, but in fact it is:
https://www.nxp.com/docs/en/errata/IMX6SLCE.pdf
You could define it like this:
#define has_err007805() (is_mx6sl() || is_mx6dl() || is_mx6solo() || is_mx6ull())
Jorge Ramirez-Ortiz
PATCH 1/1 mx6: peripheral clock from oscillator
Quoted 7 lines · Fabio Estevam
Quoted 3 lines · Jorge Ramirez-Ortiz
In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator.
I would suggest adding the optee related motivation that you explained earlier here in the commit log too.
sure, will do.
Quoted 4 lines
Quoted 2 lines
[1] Rev 2, 10/2019, ERR007805
Not clear what document this refers to.
um, weird, I just googled "imx Rev 2, 10/2019, ERR007805" and it showed the document and a link to the errata.
how do you tipically do this otherwise? I didnt want to depend on links that migh break in the future.
Quoted 5 lines
arch/arm/mach-imx/mx6/soc.c int arch_cpu_init(void) · line 474
Quoted 4 lines
/* Set perclk to source from OSC 24MHz */arch/arm/mach-imx/mx6/soc.c +1
-1-if (is_mx6sl ()) +if (is_mx6sl () ||ERRATA_ERR007805 )
Quoted 8 lines
This gives the impression that imx6sl is not affected by the erratum, but in fact it is:
https://www.nxp.com/docs/en/errata/IMX6SLCE.pdfYou could define it like this:
#define
has_err007805()(is_mx6sl()||is_mx6dl()||is_mx6solo()||is_mx6ull())
sounds good. will do (I didnt know the reason for the mx6sl configuring the clock was that same errata)
Fabio Estevam
reviewerPATCH 1/1 mx6: peripheral clock from oscillator
Quoted 2 lines · Foundries
um, weird, I just googled "imx Rev 2, 10/2019, ERR007805" and it showed the document and a link to the errata.
The errata document is specific for a SoC.
It does not help to add "Rev 2, 10/2019, ERR007805" in the commit log as we cannot know which SoC it refers to.
Just mention the SoC errata document. For example: IMX6SLCE Rev. 5, 02/2019
Jorge Ramirez-Ortiz
PATCH 1/1 mx6: peripheral clock from oscillator
Quoted 7 lines · Fabio Estevam
Quoted 2 lines · Foundries
um, weird, I just googled "imx Rev 2, 10/2019, ERR007805" and it showed the document and a link to the errata.
The errata document is specific for a SoC.
perfect. now you understand my point and why I was being generic.
Quoted 3 lines
It does not help to add "Rev 2, 10/2019, ERR007805" in the commit log as we cannot know which SoC it refers to.
um, weird....the patch indicates imx6 in the name. this should be enough no?
Quoted 2 lines
Just mention the SoC errata document. For example: IMX6SLCE Rev. 5, 02/2019
so you need the names and versions of the errata document for each SoC being affected? that being the case, should it be a patch per family or a patch per SoC?
Fabio Estevam
reviewerPATCH 1/1 mx6: peripheral clock from oscillator
Quoted 1 line · Foundries
um, weird....the patch indicates imx6 in the name. this should be enough no?
imx6 is too generic. Which imx6? imx6sx, imx6sl, imx6solo, imx6dl, imx6qp, imx6q, imx6ul, imx6ull, imx6ulz?
It is OK to keep mx6 in the Subject though.
Quoted 2 lines
so you need the names and versions of the errata document for each SoC being affected? that being the case, should it be a patch per family or a patch per SoC?
No, my point was just to replace:
[1] Rev 2, 10/2019, ERR007805 (this is not a doc reference)
by a real errata document reference. It can be imx6ull, imx6sl or any other SoC errata document like, for example:
IMX6SLCE Rev. 5, 02/2019