Skip to contentSkip to conversation

mx6: peripheral clock from oscillator

PATCH New Jorge Ramirez-Ortiz 3 participants 3 messages Oct 23, 2020 – Nov 2, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH v2 1/1 mx6: peripheral clock from oscillator

In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator.

Systems running I2C from OP-TEE before Linux executes - for example to access a Secure Element [2] providing the cryptographic support - expect this clock to be configured by the bootloader [3].

[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).

---
 arch/arm/mach-imx/mx6/soc.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
arch/arm/mach-imx/mx6/soc.c +4 -1
index e129286065..4c0a352574 100644
@@ -26,6 +26,9 @@
 #include <imx_thermal.h>
 #include <mmc.h>
 
+#define has_err007805() \
+	(is_mx6sl() || is_mx6dl() || is_mx6solo() || is_mx6ull())
+
 struct scu_regs {
 	u32	ctrl;
 	u32	config;
@@ -469,7 +472,7 @@ int arch_cpu_init(void)
 	}
 
 	/* Set perclk to source from OSC 24MHz */
-	if (is_mx6sl())
+	if (has_err007805())
 		setbits_le32(&ccm->cscmr1, MXC_CCM_CSCMR1_PER_CLK_SEL_MASK);
 
 	imx_wdog_disable_powerdown(); /* Disable PDE bit of WMCR register */
Signature · 1 line
2.17.1
reviewer
#1 lore raw

PATCH v2 1/1 mx6: peripheral clock from oscillator

Quoted 8 lines · Jorge Ramirez-Ortiz

In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator.

Systems running I2C from OP-TEE before Linux executes - for example to access a Secure Element [2] providing the cryptographic support - expect this clock to be configured by the bootloader [3].

Quoted 5 lines

[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).

#2 lore raw

PATCH v2 1/1 mx6: peripheral clock from oscillator

In reply to Jorge Ramirez-Ortiz
Quoted 10 lines

In order to be able to run the I2C bus at 400Khz, the chip errata[1] recommends that the peripheral clock runs out of the 24MHz oscillator. Systems running I2C from OP-TEE before Linux executes - for example to access a Secure Element [2] providing the cryptographic support - expect this clock to be configured by the bootloader [3].
[1] IMX6SLCE Rev. 5, 02/2019, ERR007805.
[2] OP-TEE: support for NXP SE05X Plug and Trust (patch on the list).
[3] OP-TEE: check the imx_i2c.c driver (imx6 patch on the list).

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================