ARM: dts: imx6ul: segin: Fix stmpe touchscreen subnode name
Subsystems (3)
PATCH 1/6 ARM: dts: imx6ul: segin: Fix stmpe touchscreen subnode name
The touchscreen subnode name needs to be stmpe_touchscreen as mentioned in the dt-bindings.
--- arch/arm/boot/dts/imx6ul-phytec-segin.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm/boot/dts/imx6ul-phytec-segin.dtsi +1 -1
@@ -139,7 +139,7 @@ stmpe: touchscreen@44 { pinctrl-0 = <&pinctrl_stmpe>; status = "disabled"; - touchscreen { + stmpe_touchscreen { compatible = "st,stmpe-ts"; st,sample-time = <4>; st,mod-12b = <1>;
Signature · 1 line
2.25.1
PATCH 2/6 ARM: dts: imx6: phytec: Set correct eeprom compatible
Set the correct EEPROM compatible for phyCORE-i.MX 6 and phyFLEX-i.MX 6, as stated in the device tree bindings.
--- arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 2 +- arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +1 -1
@@ -116,7 +116,7 @@ &i2c1 { status = "okay"; som_eeprom: eeprom@50 { - compatible = "atmel,24c32"; + compatible = "catalyst,24c32", "atmel,24c32"; reg = <0x50>; };
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi +1 -1
@@ -84,7 +84,7 @@ &i2c3 { status = "okay"; eeprom@50 { - compatible = "atmel,24c32"; + compatible = "st,24c32", "atmel,24c32"; reg = <0x50>; };
Signature · 1 line
2.25.1
Shawn Guo
AppliedRe: [PATCH 2/6] ARM: dts: imx6: phytec: Set correct eeprom compatible
Quoted 4 lines · Stefan Riedmueller
Set the correct EEPROM compatible for phyCORE-i.MX 6 and phyFLEX-i.MX 6, as stated in the device tree bindings.
Signed-off-by Stefan Riedmueller <[email protected]>
Applied, thanks.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 3/6 ARM: dts: imx6: phytec: Add eeprom pagesize
In reply to Stefan RiedmuellerDefining the EEPROM pagesize can increase the write speed significantly. Set it to the pagesize stated in the EEPROM's datasheet for phyCORE-i.MX 6UL, phyCORE-i.MX 6 and phyFLEX-i.MX 6.
--- arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 1 + arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 1 + arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi | 1 + 3 files changed, 3 insertions(+)
arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi +1 -0
@@ -117,6 +117,7 @@ &i2c1 { som_eeprom: eeprom@50 { compatible = "catalyst,24c32", "atmel,24c32"; + pagesize = <32>; reg = <0x50>; };
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi +1 -0
@@ -85,6 +85,7 @@ &i2c3 { eeprom@50 { compatible = "st,24c32", "atmel,24c32"; + pagesize = <32>; reg = <0x50>; };
arch/arm/boot/dts/imx6ul-phytec-phycore-som.dtsi +1 -0
@@ -75,6 +75,7 @@ &i2c1 { eeprom@52 { compatible = "catalyst,24c32", "atmel,24c32"; + pagesize = <32>; reg = <0x52>; }; };
Signature · 1 line
2.25.1
Shawn Guo
AppliedRe: [PATCH 3/6] ARM: dts: imx6: phytec: Add eeprom pagesize
Quoted 5 lines · Stefan Riedmueller
Defining the EEPROM pagesize can increase the write speed significantly. Set it to the pagesize stated in the EEPROM's datasheet for phyCORE-i.MX 6UL, phyCORE-i.MX 6 and phyFLEX-i.MX 6.
Signed-off-by Stefan Riedmueller <[email protected]>
Applied, thanks.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 4/6 ARM: dts: imx6ul: segin: Add phyBOARD-Segin with eMMC phyCORE-i.MX6UL
In reply to Stefan RiedmuellerFrom: Yunus Bas <[email protected]>
Add a PHYTEC phyBOARD-Segin full featured with phyCORE-i.MX 6UL with eMMC and following features:
- i.MX 6UL
- 512 MB RAM
- eMMC
- USB Host/OTG
- 2x 100 Mbit/s Ethernet
- RS232
- CAN
--- arch/arm/boot/dts/Makefile | 1 + .../dts/imx6ul-phytec-segin-ff-rdk-emmc.dts | 93 +++++++++++++++++++ 2 files changed, 94 insertions(+) create mode 100644 arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -615,6 +615,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-pico-dwarf.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-pico-pi.dtb \ + imx6ul-phytec-segin-ff-rdk-emmc.dtb \ imx6ul-phytec-segin-ff-rdk-nand.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +93 -0
93 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH 4/6] ARM: dts: imx6ul: segin: Add phyBOARD-Segin with eMMC phyCORE-i.MX6UL
Quoted 57 lines · Stefan Riedmueller
From: Yunus Bas <[email protected]>
Add a PHYTEC phyBOARD-Segin full featured with phyCORE-i.MX 6UL with eMMC and following features:
- i.MX 6UL
- 512 MB RAM
- eMMC
- USB Host/OTG
- 2x 100 Mbit/s Ethernet
- RS232
- CANSigned-off-by Yunus Bas <[email protected]>Signed-off-by Stefan Riedmueller <[email protected]>--- arch/arm/boot/dts/Makefile | 1 + .../dts/imx6ul-phytec-segin-ff-rdk-emmc.dts | 93 +++++++++++++++++++ 2 files changed, 94 insertions(+) create mode 100644 arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dtsarch/arm/boot/dts/Makefile +1
-0@@ -615,6 +615,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-pico-dwarf.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-pico-pi.dtb \ + imx6ul-phytec-segin-ff-rdk-emmc.dtb \ imx6ul-phytec-segin-ff-rdk-nand.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +19
-0@@ -0,0 +1,93 @@ +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) +/* + * Copyright (C) 2020 PHYTEC Messtechnik GmbH + * Author: Yunus Bas <[email protected]> + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include "imx6ul-phytec-phycore-som.dtsi" +#include "imx6ul-phytec-segin.dtsi" +#include "imx6ul-phytec-segin-peb-eval-01.dtsi" + +/ { + model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with eMMC"; + compatible = "phytec,imx6ul-pbacd10-emmc", "phytec,imx6ul-pbacd10", + "phytec,imx6ul-pcl063","fsl,imx6ul"; +}; + +&adc1 {
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts line 29
Quoted 10 lines
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +10
-0+ status = "okay"; +}; + +&can1 { + status = "okay"; +}; + +&tlv320 { + status = "okay"; +};
It breaks the alphabetic order.
Shawn
Quoted 67 lines
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +64
-0+ +&ecspi3 { + status = "okay"; +}; + +ðphy1 { + status = "okay"; +}; + +ðphy2 { + status = "okay"; +}; + +&fec1 { + status = "okay"; +}; + +&fec2 { + status = "okay"; +}; + +&i2c_rtc { + status = "okay"; +}; + +®_can1_en { + status = "okay"; +}; + +®_sound_1v8 { + status = "okay"; +}; + +®_sound_3v3 { + status = "okay"; +}; + +&sai2 { + status = "okay"; +}; + +&sound { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&usbotg1 { + status = "okay"; +}; + +&usbotg2 { + status = "okay"; +}; + +&usdhc1 { + status = "okay"; +}; + +&usdhc2 { + status = "okay"; +};Signature · 1 line
2.25.1
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH 4/6] ARM: dts: imx6ul: segin: Add phyBOARD-Segin with eMMC phyCORE-i.MX6UL
Hi Shawn,
Quoted 62 lines · Shawn Guo
Quoted 61 lines · Stefan Riedmueller
From: Yunus Bas <[email protected]>
Add a PHYTEC phyBOARD-Segin full featured with phyCORE-i.MX 6UL with eMMC and following features:
- i.MX 6UL
- 512 MB RAM
- eMMC
- USB Host/OTG
- 2x 100 Mbit/s Ethernet
- RS232
- CANSigned-off-by Yunus Bas <[email protected]>Signed-off-by Stefan Riedmueller <[email protected]>--- arch/arm/boot/dts/Makefile | 1 + .../dts/imx6ul-phytec-segin-ff-rdk-emmc.dts | 93 +++++++++++++++++++ 2 files changed, 94 insertions(+)create mode 100644
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dtsarch/arm/boot/dts/Makefile +1
-0@@ -615,6 +615,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-pico-dwarf.dtb \ imx6ul-pico-hobbit.dtb \ imx6ul-pico-pi.dtb \ + imx6ul-phytec-segin-ff-rdk-emmc.dtb \ imx6ul-phytec-segin-ff-rdk-nand.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +23
-0@@ -0,0 +1,93 @@ +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) +/* + * Copyright (C) 2020 PHYTEC Messtechnik GmbH + * Author: Yunus Bas <[email protected]> + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include "imx6ul-phytec-phycore-som.dtsi" +#include "imx6ul-phytec-segin.dtsi" +#include "imx6ul-phytec-segin-peb-eval-01.dtsi" + +/ { + model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with eMMC"; + compatible = "phytec,imx6ul-pbacd10-emmc", "phytec,imx6ul-pbacd10", + "phytec,imx6ul-pcl063","fsl,imx6ul"; +}; + +&adc1 { + status = "okay"; +}; + +&can1 {
Quoted 8 lines
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts line 29
Quoted 6 lines
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +6
-0+ status = "okay"; +}; + +&tlv320 { + status = "okay"; +};It breaks the alphabetic order.
Ah sorry, I missed that. I'll send a v2.
Thanks,
Stefan
Quoted 62 lines
Shawn
Quoted 59 lines
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +59
-0+ +&ecspi3 { + status = "okay"; +}; + +ðphy1 { + status = "okay"; +}; + +ðphy2 { + status = "okay"; +}; + +&fec1 { + status = "okay"; +}; + +&fec2 { + status = "okay"; +}; + +&i2c_rtc { + status = "okay"; +}; + +®_can1_en { + status = "okay"; +}; + +®_sound_1v8 { + status = "okay"; +}; + +®_sound_3v3 { + status = "okay"; +}; + +&sai2 { + status = "okay"; +}; + +&sound { + status = "okay"; +}; + +&uart5 { + status = "okay"; +}; + +&usbotg1 { + status = "okay"; +}; + +&usbotg2 { + status = "okay"; +}; + +&usdhc1 { + status = "okay";
Quoted 8 lines
Quoted 8 lines
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts new file +5
-0+}; + +&usdhc2 { + status = "okay"; +};Signature · 1 line
2.25.1
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH 5/6 ARM: dts: imx6ul: phytec: Add support for optional PEB-AV-02 LCD adapter
In reply to Stefan RiedmuellerThe PHYTEC PEB-AV-02 adapter adds the capability to connect a parallel LCD display to the phyBOARD-Segin full featured, either with capacitive or resistive touch.
--- .../dts/imx6ul-phytec-segin-ff-rdk-emmc.dts | 1 + .../dts/imx6ul-phytec-segin-ff-rdk-nand.dts | 1 + .../dts/imx6ul-phytec-segin-peb-av-02.dtsi | 150 ++++++++++++++++++ arch/arm/boot/dts/imx6ul-phytec-segin.dtsi | 43 ----- .../dts/imx6ull-phytec-segin-ff-rdk-emmc.dts | 1 + .../dts/imx6ull-phytec-segin-ff-rdk-nand.dts | 1 + .../dts/imx6ull-phytec-segin-peb-av-02.dtsi | 26 +++ arch/arm/boot/dts/imx6ull-phytec-segin.dtsi | 7 - 8 files changed, 180 insertions(+), 50 deletions(-) create mode 100644 arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi create mode 100644 arch/arm/boot/dts/imx6ull-phytec-segin-peb-av-02.dtsi
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-emmc.dts +1 -0
@@ -9,6 +9,7 @@ #include "imx6ul-phytec-phycore-som.dtsi" #include "imx6ul-phytec-segin.dtsi" #include "imx6ul-phytec-segin-peb-eval-01.dtsi" +#include "imx6ul-phytec-segin-peb-av-02.dtsi" / { model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with eMMC";
arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts +1 -0
@@ -9,6 +9,7 @@ #include "imx6ul-phytec-phycore-som.dtsi" #include "imx6ul-phytec-segin.dtsi" #include "imx6ul-phytec-segin-peb-eval-01.dtsi" +#include "imx6ul-phytec-segin-peb-av-02.dtsi" / { model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with NAND";
arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi new file +150 -0
150 lines not on this page · raw message
arch/arm/boot/dts/imx6ul-phytec-segin.dtsi +0 -43
67 lines not on this page · raw message
arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-emmc.dts +1 -0
@@ -9,6 +9,7 @@ #include "imx6ull-phytec-phycore-som.dtsi" #include "imx6ull-phytec-segin.dtsi" #include "imx6ull-phytec-segin-peb-eval-01.dtsi" +#include "imx6ull-phytec-segin-peb-av-02.dtsi" / { model = "PHYTEC phyBOARD-Segin i.MX6 ULL Full Featured with eMMC";
arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts +1 -0
@@ -9,6 +9,7 @@ #include "imx6ull-phytec-phycore-som.dtsi" #include "imx6ull-phytec-segin.dtsi" #include "imx6ull-phytec-segin-peb-eval-01.dtsi" +#include "imx6ull-phytec-segin-peb-av-02.dtsi" / { model = "PHYTEC phyBOARD-Segin i.MX6 ULL Full Featured with NAND";
arch/arm/boot/dts/imx6ull-phytec-segin-peb-av-02.dtsi new file +26 -0
@@ -0,0 +1,26 @@ +// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT) +/* + * Copyright (C) 2018 PHYTEC Messtechnik GmbH + * Author: Stefan Riedmueller <[email protected]> + */ + +#include "imx6ul-phytec-segin-peb-av-02.dtsi" + +&iomuxc { + /delete-node/ edtft5406grp; + /delete-node/ stmpegrp; +}; + +&iomuxc_snvs { + pinctrl_edt_ft5406: edtft5406grp { + fsl,pins = < + MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 + >; + }; + + pinctrl_stmpe: stmpegrp { + fsl,pins = < + MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059 + >; + }; +};
arch/arm/boot/dts/imx6ull-phytec-segin.dtsi +0 -7
@@ -14,7 +14,6 @@ / { &iomuxc { /delete-node/ flexcan1engrp; /delete-node/ rtcintgrp; - /delete-node/ stmpegrp; }; &iomuxc_snvs {
@@ -29,10 +28,4 @@ pinctrl_rtc_int: rtcintgrp { MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x17059 >; }; - - pinctrl_stmpe: stmpegrp { - fsl,pins = < - MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x17059 - >; - }; };
Signature · 1 line
2.25.1
PATCH 6/6 ARM: dts: imx6ul: segin: peb-av-02: Mark stmpe touch as wakeup-source
In reply to Stefan RiedmuellerMark the STMPE resistive touch controller as a wakeup-source.
--- arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi | 1 + 1 file changed, 1 insertion(+)
arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi +1 -0
@@ -70,6 +70,7 @@ stmpe: touchscreen@44 { pinctrl-0 = <&pinctrl_stmpe>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; interrupt-parent = <&gpio5>; + wakeup-source; status = "disabled"; stmpe_touchscreen {
Signature · 1 line
2.25.1
Hi,
just a gentle ping for this series.
Stefan
Quoted 14 lines · Stefan Riedmueller
The touchscreen subnode name needs to be
stmpe_touchscreenas mentioned in the dt-bindings.Signed-off-by Stefan Riedmueller <[email protected]>--- arch/arm/boot/dts/imx6ul-phytec-segin.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm/boot/dts/imx6ul-phytec-segin.dtsi +0
-0
arch/arm/boot/dts/imx6ul-phytec-segin.dtsi stmpe: touchscreen@44 { · line 145
Quoted 8 lines
arch/arm/boot/dts/imx6ul-phytec-segin.dtsi +1
-1@@ -139,7 +139,7 @@ stmpe: touchscreen@44 { pinctrl-0 = <&pinctrl_stmpe>; status = "disabled"; - touchscreen { + stmpe_touchscreen { compatible = "st,stmpe-ts"; st,sample-time = <4>; st,mod-12b = <1>;
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Shawn Guo
AppliedQuoted 4 lines · Stefan Riedmueller
The touchscreen subnode name needs to be
stmpe_touchscreenas mentioned in the dt-bindings.Signed-off-by Stefan Riedmueller <[email protected]>
Applied, thanks.
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel