dt-bindings:iio: Another set of yaml conversions.

deleted file mode 100644
index c52333bdfd19..000000000000
@@ -1,17 +0,0 @@
-* HDC100x temperature + humidity sensors
-
-Required properties:
-  - compatible: Should contain one of the following:
-	ti,hdc1000
-	ti,hdc1008
-	ti,hdc1010
-	ti,hdc1050
-	ti,hdc1080
-  - reg: i2c address of the sensor
-
-Example:
-
-hdc100x@40 {
-	compatible = "ti,hdc1000";
-	reg = <0x40>;
-};

index ab623ba930d5..d37f757e6bd1 100644
@@ -356,6 +356,16 @@ properties:
           - ti,ads7830
             # Temperature Monitoring and Fan Control
           - ti,amc6821
+            # Temperature and humidity sensor with i2c interface
+          - ti,hdc1000
+            # Temperature and humidity sensor with i2c interface
+          - ti,hdc1008
+            # Temperature and humidity sensor with i2c interface
+          - ti,hdc1010
+            # Temperature and humidity sensor with i2c interface
+          - ti,hdc1050
+            # Temperature and humidity sensor with i2c interface
+          - ti,hdc1080
             # Temperature sensor with 2-wire interface
           - ti,lm73
             # Temperature sensor with integrated fan control

deleted file mode 100644
index 97d79636f7ae..000000000000
@@ -1,13 +0,0 @@
-*HTU21 - Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
-
-Required properties:
-
-	- compatible: should be "meas,htu21" or "meas,ms8607-humidity"
-	- reg: I2C address of the sensor
-
-Example:
-
-htu21@40 {
-	compatible = "meas,htu21";
-	reg = <0x40>;
-};

index d37f757e6bd1..43febb3057b6 100644
@@ -132,6 +132,10 @@ properties:
           - mcube,mc3230
             # MEMSIC 2-axis 8-bit digital accelerometer
           - memsic,mxc6225
+            # Measurement Specialities I2C temperature and humidity sensor
+          - meas,htu21
+            # Measurement Specialities temp and humidity part of ms8607 device
+          - meas,ms8607-humidity
             # Microchip differential I2C ADC, 1 Channel, 18 bit
           - microchip,mcp3421
             # Microchip differential I2C ADC, 2 Channel, 18 bit

deleted file mode 100644
index 84d029372260..000000000000
@@ -1,30 +0,0 @@
-* HTS221 STM humidity + temperature sensor
-
-Required properties:
-- compatible: should be "st,hts221"
-- reg: i2c address of the sensor / spi cs line
-
-Optional properties:
-- drive-open-drain: the interrupt/data ready line will be configured
-  as open drain, which is useful if several sensors share the same
-  interrupt line. This is a boolean property.
-  If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or
-  IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line
-  when it is not active, whereas a pull-up one is needed when interrupt
-  line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING.
-  Refer to pinctrl/pinctrl-bindings.txt for the property description.
-- interrupts: interrupt mapping for IRQ. It should be configured with
-  flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
-  IRQ_TYPE_EDGE_FALLING.
-
-  Refer to interrupt-controller/interrupts.txt for generic interrupt
-  client node bindings.
-
-Example:
-
-hts221@5f {
-	compatible = "st,hts221";
-	reg = <0x5f>;
-	interrupt-parent = <&gpio0>;
-	interrupts = <0 IRQ_TYPE_EDGE_RISING>;
-};

52 lines not on this page · raw message

deleted file mode 100644
index ecc24c199fd6..000000000000
@@ -1,14 +0,0 @@
-* DHT11 humidity/temperature sensor (and compatibles like DHT22)
-
-Required properties:
-  - compatible: Should be "dht11"
-  - gpios: Should specify the GPIO connected to the sensor's data
-    line, see "gpios property" in
-    Documentation/devicetree/bindings/gpio/gpio.txt.
-
-Example:
-
-humidity_sensor {
-	compatible = "dht11";
-	gpios = <&gpio0 6 0>;
-}

41 lines not on this page · raw message

deleted file mode 100644
index 1f43ffa068ac..000000000000
@@ -1,17 +0,0 @@
-* MS5637 - Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor
-
-Required properties:
-
-	-compatible: should be one of the following
-		meas,ms5637
-		meas,ms5805
-		meas,ms5837
-		meas,ms8607-temppressure
-	-reg: I2C address of the sensor
-
-Example:
-
-ms5637@76 {
-	compatible = "meas,ms5637";
-	reg = <0x76>;
-};

index 43febb3057b6..8d8eadbab473 100644
@@ -134,8 +134,16 @@ properties:
           - memsic,mxc6225
             # Measurement Specialities I2C temperature and humidity sensor
           - meas,htu21
+            # Measurement Specialities I2C pressure and temperature sensor
+          - meas,ms5637
+            # Measurement Specialities I2C pressure and temperature sensor
+          - meas,ms5805
+            # Measurement Specialities I2C pressure and temperature sensor
+          - meas,ms5837
             # Measurement Specialities temp and humidity part of ms8607 device
           - meas,ms8607-humidity
+            # Measurement Specialities temp and pressure part of ms8607 device
+          - meas,ms8607-temppressure
             # Microchip differential I2C ADC, 1 Channel, 18 bit
           - microchip,mcp3421
             # Microchip differential I2C ADC, 2 Channel, 18 bit

new file mode 100644
index 000000000000..d6103be03460
@@ -0,0 +1,62 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/pressure/murata,zpa2326.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Murata ZPA2326 pressure sensor
+
+maintainers:
+  - Jonathan Cameron <[email protected]>
+
+description: |
+  Pressure sensor from Murata with SPI and I2C bus interfaces.
+
+
+properties:
+  compatible:
+    const: murata,zpa2326
+
+  reg:
+    maxItems: 1
+
+  vdd-supply: true
+  vref-supply: true
+
+  interrupts:
+    maxItems: 1
+
+  spi-max-frequency:
+    maximum: 1000000
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pressure@5c {
+            compatible = "murata,zpa2326";
+            reg = <0x5c>;
+            interrupt-parent = <&gpio>;
+            interrupts = <12>;
+            vdd-supply = <&ldo_1v8_gnss>;
+        };
+    };
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pressure@0 {
+            compatible = "murata,zpa2326";
+            reg = <0>;
+            spi-max-frequency = <500000>;
+        };
+    };
+...

deleted file mode 100644
index a36ab3e0c3f7..000000000000
@@ -1,29 +0,0 @@
-Murata ZPA2326 pressure sensor
-
-Pressure sensor from Murata with SPI and I2C bus interfaces.
-
-Required properties:
-- compatible: "murata,zpa2326"
-- reg: the I2C address or SPI chip select the device will respond to
-
-Recommended properties for SPI bus usage:
-- spi-max-frequency: maximum SPI bus frequency as documented in
-  Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Optional properties:
-- vref-supply: an optional regulator that needs to be on to provide VREF
-  power to the sensor
-- vdd-supply: an optional regulator that needs to be on to provide VDD
-  power to the sensor
-- interrupts: interrupt mapping for IRQ as documented in
-  Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
-
-Example:
-
-zpa2326@5c {
-	compatible = "murata,zpa2326";
-	reg = <0x5c>;
-	interrupt-parent = <&gpio>;
-	interrupts = <12>;
-	vdd-supply = <&ldo_1v8_gnss>;
-};

new file mode 100644
index 000000000000..4f06707450bf
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/pressure/meas,ms5611.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Measurement Specialities ms5611 and similar pressure sensors
+
+maintainers:
+  - Tomasz Duszynski <[email protected]>
+
+description: |
+  Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces.
+
+properties:
+  compatible:
+    enum:
+      - meas,ms5607
+      - meas,ms5611
+
+  reg:
+    maxItems: 1
+
+  vdd-supply: true
+
+  spi-max-frequency:
+    maximum: 20000000
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pressure@77 {
+            compatible = "meas,ms5607";
+            reg = <0x77>;
+            vdd-supply = <&ldo_3v3_gnss>;
+        };
+    };
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pressure@0 {
+            compatible = "meas,ms5611";
+            reg = <0>;
+            vdd-supply = <&ldo_3v3_gnss>;
+        };
+    };
+...

deleted file mode 100644
index 17bca866c084..000000000000
@@ -1,19 +0,0 @@
-MEAS ms5611 family pressure sensors
-
-Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces.
-
-Required properties:
-- compatible: "meas,ms5611" or "meas,ms5607"
-- reg: the I2C address or SPI chip select the device will respond to
-
-Optional properties:
-- vdd-supply: an optional regulator that needs to be on to provide VDD
-  power to the sensor.
-
-Example:
-
-ms5607@77 {
-	compatible = "meas,ms5607";
-	reg = <0x77>;
-	vdd-supply = <&ldo_3v3_gnss>;
-};

new file mode 100644
index 000000000000..69a3759e23db
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/pressure/hoperf,hp03.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HopeRF HP03 digital pressure/temperature sensors
+
+maintainers:
+  - Marek Vasut <[email protected]>
+
+description: |
+  Digital pressure and temperature sensor with an I2C interface.
+
+properties:
+  compatible:
+    const: hoperf,hp03
+
+  reg:
+    maxItems: 1
+
+  xclr-gpios:
+    description:
+      The XCLR pin is a reset of the ADC in the chip, it must be pulled
+      HI before the conversion and readout of the value from the ADC
+      registers and pulled LO afterward.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        pressure@77 {
+            compatible = "hoperf,hp03";
+            reg = <0x77>;
+            xclr-gpios = <&portc 0 0x0>;
+        };
+    };
+...

deleted file mode 100644
index 831dbee7a5c3..000000000000
@@ -1,17 +0,0 @@
-HopeRF HP03 digital pressure/temperature sensors
-
-Required properties:
-- compatible: must be "hoperf,hp03"
-- xclr-gpio: must be device tree identifier of the XCLR pin.
-             The XCLR pin is a reset of the ADC in the chip,
-             it must be pulled HI before the conversion and
-             readout of the value from the ADC registers and
-             pulled LO afterward.
-
-Example:
-
-hp03@77 {
-	compatible = "hoperf,hp03";
-	reg = <0x77>;
-	xclr-gpio = <&portc 0 0x0>;
-};

new file mode 100644
index 000000000000..66dd01506859
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/semtech,sx9500.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Semtech's SX9500 capacitive proximity button device
+
+maintainers:
+  - Jonathan Cameron <[email protected]>
+
+properties:
+  compatible:
+    const: semtech,sx9500
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description:
+      GPIO connected to the active low reset pin.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        proximity@28 {
+            compatible = "semtech,sx9500";
+            reg = <0x28>;
+            interrupt-parent = <&gpio2>;
+            interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
+            reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+        };
+    };
+...

deleted file mode 100644
index c54455db3bec..000000000000
@@ -1,23 +0,0 @@
-Semtech's SX9500 capacitive proximity button device driver
-
-Required properties:
-	- compatible: must be "semtech,sx9500"
-	- reg: i2c address where to find the device
-	- interrupts : the sole interrupt generated by the device
-
-	Refer to interrupt-controller/interrupts.txt for generic
-	interrupt client node bindings.
-
-Optional properties:
-	- reset-gpios: Reference to the GPIO connected to the device's active
-	  low reset pin.
-
-Example:
-
-sx9500@28 {
-	compatible = "semtech,sx9500";
-	reg = <0x28>;
-	interrupt-parent = <&gpio2>;
-	interrupts = <16 IRQ_TYPE_LEVEL_LOW>;
-	reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
-};

new file mode 100644
index 000000000000..656460d9d8c8
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/st,vl53l0x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ST VL53L0X ToF ranging sensor
+
+maintainers:
+  - Song Qiang <[email protected]>
+
+properties:
+  compatible:
+    const: st,vl53l0x
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        proximity@29 {
+            compatible = "st,vl53l0x";
+            reg = <0x29>;
+            interrupt-parent = <&gpio>;
+            interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+        };
+    };
+...

deleted file mode 100644
index dfe00eb961cd..000000000000
@@ -1,18 +0,0 @@
-ST VL53L0X ToF ranging sensor
-
-Required properties:
-	- compatible: must be "st,vl53l0x"
-	- reg: i2c address where to find the device
-
-Optional properties:
-	- interrupts:	Interrupt for notifying that new measurement is ready.
-			If no interrupt is specified, polling is used.
-
-Example:
-
-vl53l0x@29 {
-	compatible = "st,vl53l0x";
-	reg = <0x29>;
-	interrupt-parent = <&gpio>;
-	interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
-};

new file mode 100644
index 000000000000..7fcba5d6d508
@@ -0,0 +1,71 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/ams,as3935.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Austrian Microsystems AS3935 Franklin lightning sensor
+
+maintainers:
+  - Matt Ranostay <[email protected]>
+
+description:
+  This lightening distance sensor uses an I2C or SPI interface. The
+  binding currently only covers the SPI option.
+
+properties:
+  compatible:
+    const: ams,as3935
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency:
+    maximum: 2000000
+
+  spi-cpha: true
+
+  interrupts:
+    maxItems: 1
+
+  ams,tuning-capacitor-pf:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Calibration tuning capacitor stepping value. This will require using
+      the calibration data from the manufacturer.
+    minimum: 0
+    maximum: 120
+
+  ams,nflwdth:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Set the noise and watchdog threshold register on startup. This will
+      need to set according to the noise from the MCU board, and possibly
+      the local environment. Refer to the datasheet for the threshold settings.
+
+required:
+  - compatible
+  - reg
+  - spi-cpha
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+    lightning@0 {
+            compatible = "ams,as3935";
+            reg = <0>;
+            spi-max-frequency = <400000>;
+            spi-cpha;
+            interrupt-parent = <&gpio1>;
+            interrupts = <16 1>;
+            ams,tuning-capacitor-pf = <80>;
+            ams,nflwdth = <0x44>;
+        };
+    };
+...

deleted file mode 100644
index 849115585d55..000000000000
@@ -1,34 +0,0 @@
-Austrian Microsystems AS3935 Franklin lightning sensor device driver
-
-Required properties:
-	- compatible: must be "ams,as3935"
-	- reg: SPI chip select number for the device
-	- spi-max-frequency: specifies maximum SPI clock frequency
-	- spi-cpha: SPI Mode 1. Refer to spi/spi-bus.txt for generic SPI
-	slave node bindings.
-	- interrupts : the sole interrupt generated by the device
-
-	Refer to interrupt-controller/interrupts.txt for generic
-	interrupt client node bindings.
-
-Optional properties:
-	- ams,tuning-capacitor-pf: Calibration tuning capacitor stepping
-	  value 0 - 120pF. This will require using the calibration data from
-	  the manufacturer.
-	- ams,nflwdth: Set the noise and watchdog threshold register on
-	  startup. This will need to set according to the noise from the
-	  MCU board, and possibly the local environment. Refer to the
-	  datasheet for the threshold settings.
-
-Example:
-
-as3935@0 {
-	compatible = "ams,as3935";
-	reg = <0>;
-	spi-max-frequency = <400000>;
-	spi-cpha;
-	interrupt-parent = <&gpio1>;
-	interrupts = <16 1>;
-	ams,tuning-capacitor-pf = <80>;
-	ams,nflwdth = <0x44>;
-};

deleted file mode 100644
index 03af6b9a4d07..000000000000
@@ -1,24 +0,0 @@
-* Texas Instruments DAC5571 Family
-
-Required properties:
- - compatible: Should contain
-    "ti,dac5571"
-    "ti,dac6571"
-    "ti,dac7571"
-    "ti,dac5574"
-    "ti,dac6574"
-    "ti,dac7574"
-    "ti,dac5573"
-    "ti,dac6573"
-    "ti,dac7573"
- - reg: Should contain the DAC I2C address
-
-Optional properties:
- - vref-supply: The regulator supply for DAC reference voltage
-
-Example:
-dac@0 {
-	compatible = "ti,dac5571";
-	reg = <0x4C>;
-	vref-supply = <&vdd_supply>;
-};

52 lines not on this page · raw message

deleted file mode 100644
index e5a507db5e01..000000000000
@@ -1,23 +0,0 @@
-TI DAC7311 device tree bindings
-
-Required properties:
-- compatible: must be set to:
-	* "ti,dac7311"
-	* "ti,dac6311"
-	* "ti,dac5311"
-- reg: spi chip select number for the device
-- vref-supply: The regulator supply for ADC reference voltage
-
-Optional properties:
-- spi-max-frequency: Max SPI frequency to use
-
-Example:
-
-	spi_master {
-		dac@0 {
-			compatible = "ti,dac7311";
-			reg = <0>; /* CS0 */
-			spi-max-frequency = <1000000>;
-			vref-supply = <&vdd_supply>;
-		};
-	};

49 lines not on this page · raw message

deleted file mode 100644
index 1db45939dac9..000000000000
@@ -1,20 +0,0 @@
-TI DAC7512 DEVICETREE BINDINGS
-
-Required properties:
-
-	- "compatible"		Must be set to "ti,dac7512"
-
-Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
-apply. In particular, "reg" and "spi-max-frequency" properties must be given.
-
-
-Example:
-
-	spi_master {
-		dac7512: dac7512@0 {
-			compatible = "ti,dac7512";
-			reg = <0>; /* CS0 */
-			spi-max-frequency = <1000000>;
-		};
-	};
-

42 lines not on this page · raw message

deleted file mode 100644
index 17af395b99d9..000000000000
@@ -1,28 +0,0 @@
-* Texas Instruments Dual, 12-Bit Serial Input Digital-to-Analog Converter
-
-The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with guaranteed
-12-bit monotonicity performance over the industrial temperature range.
-Is is programmable through an SPI interface.
-
-The internal DACs are loaded when the LOADDACS pin is pulled down.
-
-https://www.ti.com/lit/ds/sbas106/sbas106.pdf
-
-Required Properties:
-- compatible: Should be one of:
-		"ti,dac7612"
-		"ti,dac7612u"
-		"ti,dac7612ub"
-- reg: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Optional Properties:
-- ti,loaddacs-gpios: GPIO descriptor for the LOADDACS pin.
-- spi-*: Definition as per Documentation/devicetree/bindings/spi/spi-bus.txt
-
-Example:
-
-	dac@1 {
-		compatible = "ti,dac7612";
-		reg = <0x1>;
-		ti,loaddacs-gpios = <&msmgpio 25 GPIO_ACTIVE_LOW>;
-	};

53 lines not on this page · raw message

new file mode 100644
index 000000000000..192b314c99d1
@@ -0,0 +1,79 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/dac/ti,dac082s085.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments DAC082s085 and similar DACs
+
+description:
+  A family of Texas Instruments 8/10/12-bit 2/4-channel DACs
+
+maintainers:
+  - Lukas Wunner <[email protected]>
+
+properties:
+  compatible:
+    enum:
+      - ti,dac082s085
+      - ti,dac102s085
+      - ti,dac122s085
+      - ti,dac084s085
+      - ti,dac104s085
+      - ti,dac124s085
+
+  reg:
+    maxItems: 1
+
+  spi-cpha: true
+  spi-cpol:
+    description:
+      Should be either spi-cpha, or spi-cpol but not both.
+
+  vref-supply:
+    description: Needed to provide output scaling.
+
+  spi-max-frequency: true
+
+required:
+  - compatible
+  - reg
+  - vref-supply
+
+additionalProperties: false
+
+allOf:
+  - $ref: '#/definitions/cpolXORcpha'
+
+definitions:
+  cpolXORcpha:
+    not:
+      required: [spi-cpha, spi-cpol]
+    oneOf:
+      - required:
+          - spi-cpha
+      - required:
+          - spi-cpol
+
+examples:
+  - |
+    vref_2v5_reg: regulator-vref {
+        compatible = "regulator-fixed";
+        regulator-name = "2v5";
+        regulator-min-microvolt = <2500000>;
+        regulator-max-microvolt = <2500000>;
+        regulator-always-on;
+    };
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        dac@0 {
+            compatible = "ti,dac082s085";
+            reg = <0>;
+            spi-max-frequency = <40000000>;
+            spi-cpol;
+            vref-supply = <&vref_2v5_reg>;
+        };
+    };
+...

deleted file mode 100644
index 9cb0e10df704..000000000000
@@ -1,34 +0,0 @@
-Texas Instruments 8/10/12-bit 2/4-channel DAC driver
-
-Required properties:
- - compatible:		Must be one of:
-			"ti,dac082s085"
-			"ti,dac102s085"
-			"ti,dac122s085"
-			"ti,dac084s085"
-			"ti,dac104s085"
-			"ti,dac124s085"
- - reg: 		Chip select number.
- - spi-cpha, spi-cpol:	SPI mode (0,1) or (1,0) must be used, so specify
-			either spi-cpha or spi-cpol (but not both).
- - vref-supply: 	Phandle to the external reference voltage supply.
-
-For other required and optional properties of SPI slave nodes please refer to
-../../spi/spi-bus.txt.
-
-Example:
-	vref_2v5_reg: regulator-vref {
-		compatible = "regulator-fixed";
-		regulator-name = "2v5";
-		regulator-min-microvolt = <2500000>;
-		regulator-max-microvolt = <2500000>;
-		regulator-always-on;
-	};
-
-	dac@0 {
-		compatible = "ti,dac082s085";
-		reg = <0>;
-		spi-max-frequency = <40000000>;
-		spi-cpol;
-		vref-supply = <&vref_2v5_reg>;
-	};

index a63e1ec18b2a..6d38ed1be3d2 100644
@@ -39,6 +39,7 @@ properties:
           - if
           - then
           - else
+          - not
   anyOf: true
   oneOf: true
   definitions: true

deleted file mode 100644
index 914610f0556e..000000000000
@@ -1,23 +0,0 @@
-Analog Devices AD7303 DAC device driver
-
-Required properties:
-	- compatible: Must be "adi,ad7303"
-	- reg: SPI chip select number for the device
-	- spi-max-frequency: Max SPI frequency to use (< 30000000)
-	- Vdd-supply: Phandle to the Vdd power supply
-
-Optional properties:
-	- REF-supply: Phandle to the external reference voltage supply. This should
-	  only be set if there is an external reference voltage connected to the REF
-	  pin. If the property is not set Vdd/2 is used as the reference voltage.
-
-Example:
-
-		ad7303@4 {
-			compatible = "adi,ad7303";
-			reg = <4>;
-			spi-max-frequency = <10000000>;
-			Vdd-supply = <&vdd_supply>;
-			adi,use-external-reference;
-			REF-supply = <&vref_supply>;
-		};

50 lines not on this page · raw message

deleted file mode 100644
index eaebbf8dab40..000000000000
@@ -1,20 +0,0 @@
-Maxim Integrated DS4422/DS4424 7-bit Sink/Source Current DAC Device Driver
-
-Datasheet publicly available at:
-https://datasheets.maximintegrated.com/en/ds/DS4422-DS4424.pdf
-
-Required properties:
-	- compatible: Should be one of
-		maxim,ds4422
-		maxim,ds4424
-	- reg: Should contain the DAC I2C address
-
-Optional properties:
-	- vcc-supply: Power supply is optional. If not defined, driver will ignore it.
-
-Example:
-	ds4224@10 {
-		compatible = "maxim,ds4424";
-		reg = <0x10>; /* When A0, A1 pins are ground */
-		vcc-supply = <&vcc_3v3>;
-	};

45 lines not on this page · raw message

new file mode 100644
index 000000000000..999c715c6179
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/dac/fsl,vf610-dac.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale vf610 Digital to Analog Converter
+
+maintainers:
+  - Sanchayan Maity <[email protected]>
+
+properties:
+  compatible:
+    const: fsl,vf610-dac
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: dac
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/clock/vf610-clock.h>
+    bus@40000000 {
+        compatible = "fsl,aips-bus", "simple-bus";
+        reg = <0x40000000 0x00070000>;
+        ranges;
+        #address-cells = <1>;
+        #size-cells = <1>;
+        dac@400cc000 {
+            compatible = "fsl,vf610-dac";
+            reg = <0x400cc000 0x1000>;
+            interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
+            clock-names = "dac";
+            clocks = <&clks VF610_CLK_DAC0>;
+        };
+    };
+...

deleted file mode 100644
index 20c6c7ae9687..000000000000
@@ -1,20 +0,0 @@
-Freescale vf610 Digital to Analog Converter bindings
-
-The devicetree bindings are for the new DAC driver written for
-vf610 SoCs from Freescale.
-
-Required properties:
-- compatible: Should contain "fsl,vf610-dac"
-- reg: Offset and length of the register set for the device
-- interrupts: Should contain the interrupt for the device
-- clocks: The clock is needed by the DAC controller
-- clock-names: Must contain "dac" matching entry in the clocks property.
-
-Example:
-dac0: dac@400cc000 {
-	compatible = "fsl,vf610-dac";
-	reg = <0x400cc000 0x1000>;
-	interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
-	clock-names = "dac";
-	clocks = <&clks VF610_CLK_DAC0>;
-};

deleted file mode 100644
index 1bc6c093fbfe..000000000000
@@ -1,35 +0,0 @@
-Microchip mcp4725 and mcp4726 DAC device driver
-
-Required properties:
-	- compatible: Must be "microchip,mcp4725" or "microchip,mcp4726"
-	- reg: Should contain the DAC I2C address
-	- vdd-supply: Phandle to the Vdd power supply. This supply is used as a
-	  voltage reference on mcp4725. It is used as a voltage reference on
-	  mcp4726 if there is no vref-supply specified.
-
-Optional properties (valid only for mcp4726):
-	- vref-supply: Optional phandle to the Vref power supply. Vref pin is
-	  used as a voltage reference when this supply is specified.
-	- microchip,vref-buffered: Boolean to enable buffering of the external
-	  Vref pin. This boolean is not valid without the vref-supply. Quoting
-	  the datasheet: This is offered in cases where the reference voltage
-	  does not have the current capability not to drop its voltage when
-	  connected to the internal resistor ladder circuit.
-
-Examples:
-
-	/* simple mcp4725 */
-	mcp4725@60 {
-		compatible = "microchip,mcp4725";
-		reg = <0x60>;
-		vdd-supply = <&vdac_vdd>;
-	};
-
-	/* mcp4726 with the buffered external reference voltage */
-	mcp4726@60 {
-		compatible = "microchip,mcp4726";
-		reg = <0x60>;
-		vdd-supply = <&vdac_vdd>;
-		vref-supply = <&vdac_vref>;
-		microchip,vref-buffered;
-	};

71 lines not on this page · raw message

deleted file mode 100644
index 54276ce8c971..000000000000
@@ -1,14 +0,0 @@
-Maxim max5821 DAC device driver
-
-Required properties:
-	- compatible: Must be "maxim,max5821"
-	- reg: Should contain the DAC I2C address
-	- vref-supply: Phandle to the vref power supply
-
-Example:
-
-	max5821@38 {
-		compatible = "maxim,max5821";
-		reg = <0x38>;
-		vref-supply = <&reg_max5821>;
-	};

44 lines not on this page · raw message

deleted file mode 100644
index 42db783c4e75..000000000000
@@ -1,19 +0,0 @@
-NXP LPC1850 DAC bindings
-
-Required properties:
-- compatible: Should be "nxp,lpc1850-dac"
-- reg: Offset and length of the register set for the ADC device
-- interrupts: The interrupt number for the ADC device
-- clocks: The root clock of the ADC controller
-- vref-supply: The regulator supply ADC reference voltage
-- resets: phandle to reset controller and line specifier
-
-Example:
-dac: dac@400e1000 {
-	compatible = "nxp,lpc1850-dac";
-	reg = <0x400e1000 0x1000>;
-	interrupts = <0>;
-	clocks = <&ccu1 CLK_APB3_DAC>;
-	vref-supply = <&reg_vdda>;
-	resets = <&rgu 42>;
-};

58 lines not on this page · raw message

deleted file mode 100644
index 2f607f41f9d3..000000000000
@@ -1,83 +0,0 @@
-Analog Devices AD5758 DAC device driver
-
-Required properties for the AD5758:
-	- compatible: Must be "adi,ad5758"
-	- reg: SPI chip select number for the device
-	- spi-max-frequency: Max SPI frequency to use (< 50000000)
-	- spi-cpha: is the only mode that is supported
-
-Required properties:
-
- - adi,dc-dc-mode: Mode of operation of the dc-to-dc converter
-		   Dynamic Power Control (DPC)
-		   In this mode, the AD5758 circuitry senses the output
-		   voltage and dynamically regulates the supply voltage,
-		   VDPC+, to meet compliance requirements plus an optimized
-		   headroom voltage for the output buffer.
-
-		   Programmable Power Control (PPC)
-		   In this mode, the VDPC+ voltage is user-programmable to
-		   a fixed level that needs to accommodate the maximum output
-		   load required.
-
-		   The output of the DAC core is either converted to a
-		   current or voltage output at the VIOUT pin. Only one mode
-		   can be enabled at any one time.
-
-		   The following values are currently supported:
-			* 1: DPC current mode
-			* 2: DPC voltage mode
-			* 3: PPC current mode
-
- Depending on the selected output mode (voltage or current) one of the
- two properties must
- be present:
-
- - adi,range-microvolt: Voltage output range
-		The array of voltage output ranges must contain two fields:
-		* <0 5000000>: 0 V to 5 V voltage range
-		* <0 10000000>: 0 V to 10 V voltage range
-		* <(-5000000) 5000000>: ±5 V voltage range
-		* <(-10000000) 10000000>: ±10 V voltage range
- - adi,range-microamp: Current output range
-		The array of current output ranges must contain two fields:
-		* <0 20000>: 0 mA to 20 mA current range
-		* <0 24000>: 0 mA to 24 mA current range
-		* <4 24000>: 4 mA to 20 mA current range
-		* <(-20000) 20000>: ±20 mA current range
-		* <(-24000) 24000>: ±24 mA current range
-		* <(-1000) 22000>: −1 mA to +22 mA current range
-
-Optional properties:
-
- - reset-gpios : GPIO spec for the RESET pin. If specified, it will be
-		 asserted during driver probe.
-
- - adi,dc-dc-ilim-microamp: The dc-to-dc converter current limit
-		   The following values are currently supported [uA]:
-			* 150000
-			* 200000
-			* 250000
-			* 300000
-			* 350000
-			* 400000
-
- - adi,slew-time-us: The time it takes for the output to reach the
- full scale [uS]
-		     The supported range is between 133us up to 1023984375us
-
-AD5758 Example:
-
-	dac@0 {
-		compatible = "adi,ad5758";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-		spi-cpha;
-
-		reset-gpios = <&gpio 22 0>;
-
-		adi,dc-dc-mode = <2>;
-		adi,range-microvolt = <0 10000000>;
-		adi,dc-dc-ilim-microamp = <200000>;
-		adi,slew-time-us = <125000>;
-	};

129 lines not on this page · raw message

new file mode 100644
index 000000000000..d6965a0c1cf3
@@ -0,0 +1,50 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/temperature/melexis,mlx90614.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Melexis MLX90614 contactless IR temperature sensor
+
+maintainers:
+  - Peter Meerwald <[email protected]>
+  - Crt Mori <[email protected]>
+
+description: |
+  http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx
+
+properties:
+  compatible:
+    const: melexis,mlx90614
+
+  reg:
+    maxItems: 1
+
+  wakeup-gpios:
+    description:
+      GPIO connected to the SDA line to hold low in order to wake up the
+      device.  In normal operation, the GPIO is set as input and will
+      not interfere in I2C communication.  There is no need for a GPIO
+      driving the SCL line.  If no GPIO is given, power management is disabled.
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        temp-sensor@5a {
+            compatible = "melexis,mlx90614";
+            reg = <0x5a>;
+            wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+        };
+    };
+...

deleted file mode 100644
index 9be57b036092..000000000000
@@ -1,24 +0,0 @@
-* Melexis MLX90614 contactless IR temperature sensor
-
-http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx
-
-Required properties:
-
-  - compatible: should be "melexis,mlx90614"
-  - reg: the I2C address of the sensor
-
-Optional properties:
-
-  - wakeup-gpios: device tree identifier of the GPIO connected to the SDA line
-      to hold low in order to wake up the device.  In normal operation, the
-      GPIO is set as input and will not interfere in I2C communication.  There
-      is no need for a GPIO driving the SCL line.  If no GPIO is given, power
-      management is disabled.
-
-Example:
-
-mlx90614@5a {
-	compatible = "melexis,mlx90614";
-	reg = <0x5a>;
-	wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
-};

new file mode 100644
index 000000000000..b547ddcd544a
@@ -0,0 +1,55 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/temperature/melexis,mlx90632.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Melexis MLX90632 contactless Infra Red temperature sensor
+
+maintainers:
+  - Crt Mori <[email protected]>
+
+description: |
+  https://www.melexis.com/en/documents/documentation/datasheets/datasheet-mlx90632
+
+  There are various applications for the Infra Red contactless temperature
+  sensor and MLX90632 is most suitable for consumer applications where
+  measured object temperature is in range between -20 to 200 degrees
+  Celsius with relative error of measurement below 1 degree Celsius in
+  object temperature range for industrial applications. Since it can
+  operate and measure ambient temperature in range of -20 to 85 degrees
+  Celsius it is suitable also for outdoor use.
+
+  Be aware that electronics surrounding the sensor can increase ambient
+  temperature. MLX90632 can be calibrated to reduce the housing effect via
+  already existing EEPROM parameters.
+
+  Since measured object emissivity effects Infra Red energy emitted,
+  emissivity should be set before requesting the object temperature.
+
+properties:
+  compatible:
+    const: melexis,mlx90632
+
+  reg:
+    maxItems: 1
+    description: Default is 0x3a, but can be reprogrammed.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        temp-sensor@3a {
+            compatible = "melexis,mlx90632";
+            reg = <0x3a>;
+        };
+    };
+...

deleted file mode 100644
index 0b05812001f8..000000000000
@@ -1,28 +0,0 @@
-* Melexis MLX90632 contactless Infra Red temperature sensor
-
-Link to datasheet: https://www.melexis.com/en/documents/documentation/datasheets/datasheet-mlx90632
-
-There are various applications for the Infra Red contactless temperature sensor
-and MLX90632 is most suitable for consumer applications where measured object
-temperature is in range between -20 to 200 degrees Celsius with relative error
-of measurement below 1 degree Celsius in object temperature range for
-industrial applications. Since it can operate and measure ambient temperature
-in range of -20 to 85 degrees Celsius it is suitable also for outdoor use.
-
-Be aware that electronics surrounding the sensor can increase ambient
-temperature. MLX90632 can be calibrated to reduce the housing effect via
-already existing EEPROM parameters.
-
-Since measured object emissivity effects Infra Red energy emitted, emissivity
-should be set before requesting the object temperature.
-
-Required properties:
-  - compatible: should be "melexis,mlx90632"
-  - reg: the I2C address of the sensor (default 0x3a)
-
-Example:
-
-mlx90632@3a {
-	compatible = "melexis,mlx90632";
-	reg = <0x3a>;
-};

deleted file mode 100644
index 0d5cc5595d0c..000000000000
@@ -1,19 +0,0 @@
-* TSYS01 - Measurement Specialties temperature sensor
-
-Required properties:
-
-	- compatible: should be "meas,tsys01"
-	- reg: I2C address of the sensor (changeable via CSB pin)
-
-		------------------------
-		| CSB | Device Address |
-		------------------------
-		   1         0x76
-		   0	     0x77
-
-Example:
-
-tsys01@76 {
-	compatible = "meas,tsys01";
-	reg = <0x76>;
-};

index 8d8eadbab473..cb4fd8f29675 100644
@@ -144,6 +144,8 @@ properties:
           - meas,ms8607-humidity
             # Measurement Specialities temp and pressure part of ms8607 device
           - meas,ms8607-temppressure
+            # Measurement Specialties temperature sensor
+          - meas,tsys01
             # Microchip differential I2C ADC, 1 Channel, 18 bit
           - microchip,mcp3421
             # Microchip differential I2C ADC, 2 Channel, 18 bit

deleted file mode 100644
index 06ab43bb4de8..000000000000
@@ -1,24 +0,0 @@
-Maxim MAX31856 thermocouple support
-
-https://datasheets.maximintegrated.com/en/ds/MAX31856.pdf
-
-Optional property:
-	- thermocouple-type: Type of thermocouple (THERMOCOUPLE_TYPE_K if
-		omitted). Supported types are B, E, J, K, N, R, S, T.
-
-Required properties:
-	- compatible: must be "maxim,max31856"
-	- reg: SPI chip select number for the device
-	- spi-max-frequency: As per datasheet max. supported freq is 5000000
-	- spi-cpha: must be defined for max31856 to enable SPI mode 1
-
-	Refer to spi/spi-bus.txt for generic SPI slave bindings.
-
- Example:
-	temp-sensor@0 {
-		compatible = "maxim,max31856";
-		reg = <0>;
-		spi-max-frequency = <5000000>;
-		spi-cpha;
-		thermocouple-type = <THERMOCOUPLE_TYPE_K>;
-	};

54 lines not on this page · raw message

new file mode 100644
index 000000000000..9969bac66aa1
@@ -0,0 +1,76 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/temperature/maxim,max31855k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Maxim MAX31855 and similar thermocouples
+
+maintainers:
+  - Matt Ranostay <[email protected]>
+
+description: |
+  https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf
+  https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf
+
+properties:
+  compatible:
+    description:
+      The generic maxim,max31855 compatible is deprecated in favour of
+      the thermocouple type specific variants.
+    enum:
+      - maxim,max6675
+      - maxim,max31855
+      - maxim,max31855k
+      - maxim,max31855j
+      - maxim,max31855n
+      - maxim,max31855s
+      - maxim,max31855t
+      - maxim,max31855e
+      - maxim,max31855r
+
+  reg:
+    maxItems: 1
+
+  spi-max-frequency: true
+  spi-cpha: true
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - maxim,max6675
+    then:
+      required:
+        - spi-cpha
+    else:
+      properties:
+        spi-cpha: false
+
+additionalProperties: false
+
+examples:
+  - |
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        temp-sensor@0 {
+            compatible = "maxim,max31855k";
+            reg = <0>;
+            spi-max-frequency = <4300000>;
+        };
+        temp-sensor@1 {
+            compatible = "maxim,max6675";
+            reg = <1>;
+            spi-max-frequency = <4300000>;
+            spi-cpha;
+        };
+    };
+...

deleted file mode 100644
index bb85cd0e039c..000000000000
@@ -1,24 +0,0 @@
-Maxim thermocouple support
-
-* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf
-* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf
-
-Required properties:
-
-	- compatible: must be "maxim,max6675" or one of the following:
-	   "maxim,max31855k", "maxim,max31855j", "maxim,max31855n",
-	   "maxim,max31855s", "maxim,max31855t", "maxim,max31855e",
-	   "maxim,max31855r"; the generic "max,max31855" is deprecated.
-	- reg: SPI chip select number for the device
-	- spi-max-frequency: must be 4300000
-	- spi-cpha: must be defined for max6675 to enable SPI mode 1
-
-	Refer to spi/spi-bus.txt for generic SPI slave bindings.
-
-Example:
-
-	max31855@0 {
-		compatible = "maxim,max31855k";
-		reg = <0>;
-		spi-max-frequency = <4300000>;
-	};

new file mode 100644
index 000000000000..3c2b7189fa2e
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/temperature/ti,tmp007.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: IR thermopile sensor with integrated math engine
+
+maintainers:
+  - Manivannan Sadhasivam <[email protected]>
+
+description: |
+  http://www.ti.com/lit/ds/symlink/tmp007.pdf
+
+properties:
+  compatible:
+    const: ti,tmp007
+
+  reg:
+    description: |
+      The I2C address of the sensor (changeable via ADR pins)
+      ------------------------------
+      |ADR1 | ADR0 | Device Address|
+      ------------------------------
+         0      0        0x40
+         0      1        0x41
+         0     SDA       0x42
+         0     SCL       0x43
+         1      0        0x44
+         1      1        0x45
+         1     SDA       0x46
+         1     SCL       0x47
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        temp-sensor@40 {
+            compatible = "ti,tmp007";
+            reg = <0x40>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <5 0x08>;
+        };
+    };
+...

deleted file mode 100644
index da0af234a357..000000000000
@@ -1,33 +0,0 @@
-* TI TMP007 - IR thermopile sensor with integrated math engine
-
-Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf
-
-Required properties:
-
-  - compatible: should be "ti,tmp007"
-  - reg: the I2C address of the sensor (changeable via ADR pins)
-		------------------------------
-		|ADR1 | ADR0 | Device Address|
-		------------------------------
-		   0      0        0x40
-		   0	  1	   0x41
-		   0	 SDA       0x42
-		   0     SCL       0x43
-		   1      0        0x44
-		   1      1        0x45
-		   1	 SDA	   0x46
-		   1     SCL       0x47
-
-Optional properties:
-
-  - interrupts: interrupt mapping for GPIO IRQ (level active low)
-
-Example:
-
-tmp007@40 {
-        compatible = "ti,tmp007";
-        reg = <0x40>;
-	interrupt-parent = <&gpio0>;
-	interrupts = <5 0x08>;
-};
-