Skip to contentSkip to conversation

dt-bindings: soc: imx: Add binding doc for spba bus

PATCH Superseded Adam Ford 3 participants 9 messages Nov 7, 2020 – Dec 1, 2020

Subsystems (2)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore

Adam Ford

author
#0 lore raw

PATCH v4 1/5 dt-bindings: soc: imx: Add binding doc for spba bus

Add binding doc for fsl,spba-bus.

---

V4:  Correct errors in YAML
V3:  New to series
 .../devicetree/bindings/bus/fsl,spba-bus.yaml | 66 +++++++++++++++++++
 1 file changed, 66 insertions(+)
Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml new file +66 -0
new file mode 100644
index 000000000000..d1037acd2734
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/bus/simple-pm-bus.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Shared Peripherals Bus Interface
+
+maintainers:
+  - Shawn Guo <[email protected]>
+
+description: |
+  A simple bus enabling access to shared peripherals.
+
+  The "spba-bus" follows the "simple-bus" set of properties, as
+  specified in the Devicetree Specification.  It is an extension of
+  "simple-bus" because the SDMA controller uses this compatible flag to
+  determine which peripherals are available to it and the range over which
+  the SDMA can access.  There are no special clocks for the bus, because
+  the SDMA controller itself has its interrupt, and clock assignments.
+
+select:
+  properties:
+    compatible:
+      contains:
+        const: fsl,spba-bus
+  required:
+    - compatible
+
+properties:
+  $nodename:
+    pattern: "^bus(@[0-9a-f]+)?$"
+
+  compatible:
+    contains:
+      const: fsl,spba-bus
+  items:
+    - const: fsl,spba-bus
+    - const: simple-bus
+
+  '#address-cells':
+    enum: [ 1, 2 ]
+
+  '#size-cells':
+    enum: [ 1, 2 ]
+
+  ranges: true
+
+required:
+  - compatible
+  - '#address-cells'
+  - '#size-cells'
+  - ranges
+
+additionalProperties: true
+
+type: object
+
+examples:
+  - |
+    bus {
+        compatible = "fsl,spba-bus", "simple-bus";
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges;
+    };
Signature · 1 line
2.25.1
author
#1 lore raw

PATCH v4 2/5 arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter

The driver exists for the Enhanced Asynchronous Sample Rate Converter (EASRC) Controller, but there isn't a device tree entry for it.

On the vendor kernel, they put this on a spba-bus for SDMA support.

Add the node for the spba-bus with the easrc node inside.

---

V4:  No change
V3:  Change spba-bus@30000000 to spba: bus@30000000
V2:  Make the DT node more in-line with the dt binding and remove
     vendor customizations that are not applicable.
 arch/arm64/boot/dts/freescale/imx8mn.dtsi | 28 +++++++++++++++++++++++
 1 file changed, 28 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn.dtsi +28 -0
index a06d2a6268e6..61560c083300 100644
@@ -253,6 +253,34 @@ aips1: bus@30000000 {
 			#size-cells = <1>;
 			ranges;
 
+			spba: bus@30000000 {
+				compatible = "fsl,spba-bus", "simple-bus";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				reg = <0x30000000 0x100000>;
+				ranges;
+
+				easrc: easrc@300c0000 {
+					compatible = "fsl,imx8mn-easrc";
+					reg = <0x300c0000 0x10000>;
+					interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_ASRC_ROOT>;
+					clock-names = "mem";
+					dmas = <&sdma2 16 23 0> , <&sdma2 17 23 0>,
+					       <&sdma2 18 23 0> , <&sdma2 19 23 0>,
+					       <&sdma2 20 23 0> , <&sdma2 21 23 0>,
+					       <&sdma2 22 23 0> , <&sdma2 23 23 0>;
+					dma-names = "ctx0_rx", "ctx0_tx",
+						    "ctx1_rx", "ctx1_tx",
+						    "ctx2_rx", "ctx2_tx",
+						    "ctx3_rx", "ctx3_tx";
+					firmware-name = "imx/easrc/easrc-imx8mn.bin";
+					fsl,asrc-rate  = <8000>;
+					fsl,asrc-format = <2>;
+					status = "disabled";
+				};
+			};
+
 			gpio1: gpio@30200000 {
 				compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
 				reg = <0x30200000 0x10000>;
Signature · 1 line
2.25.1
author
#2 lore raw

Re: [PATCH V4 2/5] arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter

Quoted 9 lines · Adam Ford

The driver exists for the Enhanced Asynchronous Sample Rate Converter (EASRC) Controller, but there isn't a device tree entry for it.

On the vendor kernel, they put this on a spba-bus for SDMA support.

Add the node for the spba-bus with the easrc node inside.

Shawn,

I split the dt-binding into a separate patch since I was struggling with checking the yaml syntax. Rob helped me find the proper branch to use. I hope it goes through this time.

Do you have any comments on the rest of the series? I would like to fix them if you have any concerns so I can resend if/when the dt-binding is accepted.

thanks,

adam

Quoted 50 lines

---

V4:  No change
V3:  Change spba-bus@30000000 to spba: bus@30000000
V2:  Make the DT node more in-line with the dt binding and remove
     vendor customizations that are not applicable.
 arch/arm64/boot/dts/freescale/imx8mn.dtsi | 28 +++++++++++++++++++++++
 1 file changed, 28 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn.dtsi +28 -1
index a06d2a6268e6..61560c083300 100644
@@ -253,6 +253,34 @@ aips1: bus@30000000 {
                        #size-cells = <1>;
                        ranges;
 
+                       spba: bus@30000000 {
+                               compatible = "fsl,spba-bus", "simple-bus";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               reg = <0x30000000 0x100000>;
+                               ranges;
+
+                               easrc: easrc@300c0000 {
+                                       compatible = "fsl,imx8mn-easrc";
+                                       reg = <0x300c0000 0x10000>;
+                                       interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+                                       clocks = <&clk IMX8MN_CLK_ASRC_ROOT>;
+                                       clock-names = "mem";
+                                       dmas = <&sdma2 16 23 0> , <&sdma2 17 23 0>,
+                                              <&sdma2 18 23 0> , <&sdma2 19 23 0>,
+                                              <&sdma2 20 23 0> , <&sdma2 21 23 0>,
+                                              <&sdma2 22 23 0> , <&sdma2 23 23 0>;
+                                       dma-names = "ctx0_rx", "ctx0_tx",
+                                                   "ctx1_rx", "ctx1_tx",
+                                                   "ctx2_rx", "ctx2_tx",
+                                                   "ctx3_rx", "ctx3_tx";
+                                       firmware-name = "imx/easrc/easrc-imx8mn.bin";
+                                       fsl,asrc-rate  = <8000>;
+                                       fsl,asrc-format = <2>;
+                                       status = "disabled";
+                               };
+                       };
+
                        gpio1: gpio@30200000 {
                                compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
                                reg = <0x30200000 0x10000>;
--

2.25.1

author
#3 lore raw

Re: [PATCH V4 2/5] arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter

Quoted 14 lines · Adam Ford
Quoted 9 lines · Adam Ford

The driver exists for the Enhanced Asynchronous Sample Rate Converter (EASRC) Controller, but there isn't a device tree entry for it.

On the vendor kernel, they put this on a spba-bus for SDMA support.

Add the node for the spba-bus with the easrc node inside.

Shawn,

Quoted 7 lines

I split the dt-binding into a separate patch since I was struggling with checking the yaml syntax. Rob helped me find the proper branch to use. I hope it goes through this time.

Do you have any comments on the rest of the series? I would like to fix them if you have any concerns so I can resend if/when the dt-binding is accepted.

Shawn,

The dt-binding was accepted per [1]. How do you want me to proceed for the rest of the series? I can resend the other parts without the dt-binding if you like.

thanks,

adam
[1] - https://lkml.org/lkml/2020/11/30/1211

Quoted 55 lines

thanks,

adam

Quoted 50 lines

---

V4:  No change
V3:  Change spba-bus@30000000 to spba: bus@30000000
V2:  Make the DT node more in-line with the dt binding and remove
     vendor customizations that are not applicable.
 arch/arm64/boot/dts/freescale/imx8mn.dtsi | 28 +++++++++++++++++++++++
 1 file changed, 28 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn.dtsi +28 -1
index a06d2a6268e6..61560c083300 100644
@@ -253,6 +253,34 @@ aips1: bus@30000000 {
                        #size-cells = <1>;
                        ranges;
 
+                       spba: bus@30000000 {
+                               compatible = "fsl,spba-bus", "simple-bus";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               reg = <0x30000000 0x100000>;
+                               ranges;
+
+                               easrc: easrc@300c0000 {
+                                       compatible = "fsl,imx8mn-easrc";
+                                       reg = <0x300c0000 0x10000>;
+                                       interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+                                       clocks = <&clk IMX8MN_CLK_ASRC_ROOT>;
+                                       clock-names = "mem";
+                                       dmas = <&sdma2 16 23 0> , <&sdma2 17 23 0>,
+                                              <&sdma2 18 23 0> , <&sdma2 19 23 0>,
+                                              <&sdma2 20 23 0> , <&sdma2 21 23 0>,
+                                              <&sdma2 22 23 0> , <&sdma2 23 23 0>;
+                                       dma-names = "ctx0_rx", "ctx0_tx",
+                                                   "ctx1_rx", "ctx1_tx",
+                                                   "ctx2_rx", "ctx2_tx",
+                                                   "ctx3_rx", "ctx3_tx";
+                                       firmware-name = "imx/easrc/easrc-imx8mn.bin";
+                                       fsl,asrc-rate  = <8000>;
+                                       fsl,asrc-format = <2>;
+                                       status = "disabled";
+                               };
+                       };
+
                        gpio1: gpio@30200000 {
                                compatible = "fsl,imx8mn-gpio", "fsl,imx35-gpio";
                                reg = <0x30200000 0x10000>;
--

2.25.1

#4 lore raw

Re: [PATCH V4 2/5] arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter

Quoted 23 lines · Adam Ford
Quoted 14 lines · Adam Ford
Quoted 9 lines · Adam Ford

The driver exists for the Enhanced Asynchronous Sample Rate Converter (EASRC) Controller, but there isn't a device tree entry for it.

On the vendor kernel, they put this on a spba-bus for SDMA support.

Add the node for the spba-bus with the easrc node inside.

Shawn,

Quoted 7 lines

I split the dt-binding into a separate patch since I was struggling with checking the yaml syntax. Rob helped me find the proper branch to use. I hope it goes through this time.

Do you have any comments on the rest of the series? I would like to fix them if you have any concerns so I can resend if/when the dt-binding is accepted.

Quoted 5 lines

Shawn,

The dt-binding was accepted per [1]. How do you want me to proceed for the rest of the series? I can resend the other parts without the dt-binding if you like.

Applied 4 DTS patches, thanks.

author
#5 lore raw

PATCH v4 3/5 arm64: dts: imx8mn: Add SAI nodes

In reply to Adam Ford

The i.MX8M Nano has several SAI nodes available to it. Enable them.

---

V4:  No Change
V3:  No Change
V2:  No Change
 arch/arm64/boot/dts/freescale/imx8mn.dtsi | 72 +++++++++++++++++++++++
 1 file changed, 72 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn.dtsi +72 -0
index 61560c083300..6ea0d43a78a3 100644
@@ -260,6 +260,78 @@ spba: bus@30000000 {
 				reg = <0x30000000 0x100000>;
 				ranges;
 
+				sai2: sai@30020000 {
+					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					reg = <0x30020000 0x10000>;
+					interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SAI2_IPG>,
+						<&clk IMX8MN_CLK_DUMMY>,
+						<&clk IMX8MN_CLK_SAI2_ROOT>,
+						<&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_CLK_DUMMY>;
+					clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+					dmas = <&sdma2 2 2 0>, <&sdma2 3 2 0>;
+					dma-names = "rx", "tx";
+					status = "disabled";
+				};
+
+				sai3: sai@30030000 {
+					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					reg = <0x30030000 0x10000>;
+					interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SAI3_IPG>,
+						 <&clk IMX8MN_CLK_DUMMY>,
+						 <&clk IMX8MN_CLK_SAI3_ROOT>,
+						 <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_CLK_DUMMY>;
+					clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+					dmas = <&sdma2 4 2 0>, <&sdma2 5 2 0>;
+					dma-names = "rx", "tx";
+					status = "disabled";
+				};
+
+				sai5: sai@30050000 {
+					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					reg = <0x30050000 0x10000>;
+					interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SAI5_IPG>,
+						 <&clk IMX8MN_CLK_DUMMY>,
+						 <&clk IMX8MN_CLK_SAI5_ROOT>,
+						 <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_CLK_DUMMY>;
+					clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+					dmas = <&sdma2 8 2 0>, <&sdma2 9 2 0>;
+					dma-names = "rx", "tx";
+					fsl,shared-interrupt;
+					fsl,dataline = <0 0xf 0xf>;
+					status = "disabled";
+				};
+
+				sai6: sai@30060000 {
+					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					reg = <0x30060000  0x10000>;
+					interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SAI6_IPG>,
+						 <&clk IMX8MN_CLK_DUMMY>,
+						 <&clk IMX8MN_CLK_SAI6_ROOT>,
+						 <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_CLK_DUMMY>;
+					clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+					dmas = <&sdma2 10 2 0>, <&sdma2 11 2 0>;
+					dma-names = "rx", "tx";
+					status = "disabled";
+				};
+
+				sai7: sai@300b0000 {
+					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					reg = <0x300b0000 0x10000>;
+					interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_SAI7_IPG>,
+						 <&clk IMX8MN_CLK_DUMMY>,
+						 <&clk IMX8MN_CLK_SAI7_ROOT>,
+						 <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_CLK_DUMMY>;
+					clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3";
+					dmas = <&sdma2 12 2 0>, <&sdma2 13 2 0>;
+					dma-names = "rx", "tx";
+					status = "disabled";
+				};
+
 				easrc: easrc@300c0000 {
 					compatible = "fsl,imx8mn-easrc";
 					reg = <0x300c0000 0x10000>;
Signature · 1 line
2.25.1
author
#6 lore raw

PATCH v4 4/5 arm64: dts: imx8mn: Add support for micfil

In reply to Adam Ford

The i.MX8M Nano has supports the MICFIL digital interface. It's a 16-bit audio signal from a PDM microphone bitstream. The driver is already in the kernel, but the node is missing.

Add the micfil node.

---

V4:  No Change
V3:  No Change
V2:  Change micfil@30080000 to audio-controller@30080000
 arch/arm64/boot/dts/freescale/imx8mn.dtsi | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn.dtsi +19 -0
index 6ea0d43a78a3..aa3f1eb391bd 100644
@@ -318,6 +318,25 @@ sai6: sai@30060000 {
 					status = "disabled";
 				};
 
+				micfil: audio-controller@30080000 {
+					compatible = "fsl,imx8mm-micfil";
+					reg = <0x30080000 0x10000>;
+					interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+						     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_PDM_IPG>,
+						 <&clk IMX8MN_CLK_PDM_ROOT>,
+						 <&clk IMX8MN_AUDIO_PLL1_OUT>,
+						 <&clk IMX8MN_AUDIO_PLL2_OUT>,
+						 <&clk IMX8MN_CLK_EXT3>;
+					clock-names = "ipg_clk", "ipg_clk_app",
+						      "pll8k", "pll11k", "clkext3";
+					dmas = <&sdma2 24 25 0x80000000>;
+					dma-names = "rx";
+					status = "disabled";
+				};
+
 				sai7: sai@300b0000 {
 					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
 					reg = <0x300b0000 0x10000>;
Signature · 1 line
2.25.1
author
#7 lore raw

PATCH v4 5/5 arm64: dts: imx8mn: Add node for SPDIF

In reply to Adam Ford

The i.MX8M Nano can support SPDIF which is compatible to the IP used on the i.MX35.

Add the node.

---

V4:  No Change
V3:  No Change
V2:  No Change
 arch/arm64/boot/dts/freescale/imx8mn.dtsi | 24 +++++++++++++++++++++++
 1 file changed, 24 insertions(+)
arch/arm64/boot/dts/freescale/imx8mn.dtsi +24 -0
index aa3f1eb391bd..ee1790230490 100644
@@ -337,6 +337,30 @@ micfil: audio-controller@30080000 {
 					status = "disabled";
 				};
 
+				spdif1: spdif@30090000 {
+					compatible = "fsl,imx35-spdif";
+					reg = <0x30090000 0x10000>;
+					interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MN_CLK_AUDIO_AHB>, /* core */
+						 <&clk IMX8MN_CLK_24M>, /* rxtx0 */
+						 <&clk IMX8MN_CLK_SPDIF1>, /* rxtx1 */
+						 <&clk IMX8MN_CLK_DUMMY>, /* rxtx2 */
+						 <&clk IMX8MN_CLK_DUMMY>, /* rxtx3 */
+						 <&clk IMX8MN_CLK_DUMMY>, /* rxtx4 */
+						 <&clk IMX8MN_CLK_AUDIO_AHB>, /* rxtx5 */
+						 <&clk IMX8MN_CLK_DUMMY>, /* rxtx6 */
+						 <&clk IMX8MN_CLK_DUMMY>, /* rxtx7 */
+						 <&clk IMX8MN_CLK_DUMMY>; /* spba */
+					clock-names = "core", "rxtx0",
+						      "rxtx1", "rxtx2",
+						      "rxtx3", "rxtx4",
+						      "rxtx5", "rxtx6",
+						      "rxtx7", "spba";
+					dmas = <&sdma2 28 18 0>, <&sdma2 29 18 0>;
+					dma-names = "rx", "tx";
+					status = "disabled";
+				};
+
 				sai7: sai@300b0000 {
 					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
 					reg = <0x300b0000 0x10000>;
Signature · 1 line
2.25.1
maintainer
#8 lore raw
In reply to Adam Ford
Quoted 10 lines · Adam Ford

Add binding doc for fsl,spba-bus.

---

V4:  Correct errors in YAML
V3:  New to series
 .../devicetree/bindings/bus/fsl,spba-bus.yaml | 66 +++++++++++++++++++
 1 file changed, 66 insertions(+)

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml: properties:items: [{'const': 'fsl,spba-bus'}, {'const': 'simple-bus'}] is not of type 'object', 'boolean'
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml: Additional properties are not allowed ('type' was unexpected)
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml: properties: {'enum': ['$ref', 'additionalItems', 'additionalProperties', 'allOf', 'anyOf', 'const', 'contains', 'default', 'dependencies', 'deprecated', 'description', 'else', 'enum', 'if', 'items', 'maxItems', 'maximum', 'minItems', 'minimum', 'multipleOf', 'not', 'oneOf', 'pattern', 'patternProperties', 'properties', 'propertyNames', 'required', 'then', 'unevaluatedProperties']} is not allowed for 'items' ./Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml: $id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/bus/fsl,spba-bus.yaml#
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml: ignoring, error in schema: properties: items
warning: no schema found in file: ./Documentation/devicetree/bindings/bus/fsl,spba-bus.yaml

See https://patchwork.ozlabs.org/patch/1396117

The base for the patch is generally the last rc1. Any dependencies should be noted.

If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:

pip3 install dtschema --upgrade

Please check and re-submit.

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel