add support for Compulab iot-gate-imx8
Subsystems (3)
v3 cover add support for Compulab iot-gate-imx8
From: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate). The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console
Ying-Chun Liu (PaulLiu) (2):
arm: dts: add imx8mm-cl-iot-gate dts file
arm: imx8m: add support for Compulab iot-gate-imx8
(imx8mm-cl-iot-gate)
arch/arm/dts/Makefile | 2 + arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi | 131 ++ arch/arm/dts/imx8mm-cl-iot-gate.dts | 550 +++++ arch/arm/mach-imx/imx8m/Kconfig | 8 + board/compulab/imx8mm-cl-iot-gate/Kconfig | 12 + board/compulab/imx8mm-cl-iot-gate/MAINTAINERS | 6 + board/compulab/imx8mm-cl-iot-gate/Makefile | 13 + .../compulab/imx8mm-cl-iot-gate/ddr/Makefile | 8 + board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c | 211 ++ board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h | 26 + .../ddr/lpddr4_timing_01061010.1_2.c | 1848 +++++++++++++++++ .../ddr/lpddr4_timing_01061010.c | 1847 ++++++++++++++++ .../ddr/lpddr4_timing_ff000110.c | 1847 ++++++++++++++++ .../ddr/lpddr4_timing_ff020008.c | 1847 ++++++++++++++++ .../imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c | 69 + board/compulab/imx8mm-cl-iot-gate/spl.c | 187 ++ configs/imx8mm-cl-iot-gate_defconfig | 130 ++ include/configs/imx8mm-cl-iot-gate.h | 190 ++ 18 files changed, 8932 insertions(+) create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate.dts create mode 100644 board/compulab/imx8mm-cl-iot-gate/Kconfig create mode 100644 board/compulab/imx8mm-cl-iot-gate/MAINTAINERS create mode 100644 board/compulab/imx8mm-cl-iot-gate/Makefile create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/Makefile create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.1_2.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff000110.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff020008.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/spl.c create mode 100644 configs/imx8mm-cl-iot-gate_defconfig create mode 100644 include/configs/imx8mm-cl-iot-gate.h
Signature · 1 line
2.29.2
PATCH v3 1/2 arm: dts: add imx8mm-cl-iot-gate dts file
From: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Add board dts for imx8mm-cl-iot-gate
--- arch/arm/dts/Makefile | 2 + arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi | 131 +++++ arch/arm/dts/imx8mm-cl-iot-gate.dts | 550 ++++++++++++++++++++ 3 files changed, 683 insertions(+) create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate.dts
arch/arm/dts/Makefile +2 -0
@@ -1003,6 +1003,8 @@ dtb-$(CONFIG_TARGET_DURIAN) += phytium-durian.dtb dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb +dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE) += imx8mm-cl-iot-gate.dtb + targets += $(dtb-y) # Add any required device tree compiler flags here
arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi new file +131 -0
131 lines not on this page · raw message
arch/arm/dts/imx8mm-cl-iot-gate.dts new file +550 -0
550 lines not on this page · raw message
Signature · 1 line
2.29.2
PATCH v3 1/2 arm: dts: add imx8mm-cl-iot-gate dts file
Quoted 11 lines · Ying-Chun Liu
From: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Add board dts for imx8mm-cl-iot-gate
Signed-off-by Kirill Kapranov <[email protected]>Signed-off-by Uri Mashiach <[email protected]>Signed-off-by Valentin Raevsky <[email protected]>Signed-off-by Ying-Chun Liu (PaulLiu) <[email protected]>Cc Peter Robinson <[email protected]>---
What's changed since the last version. You should put a change log at this point.
Quoted 716 lines
arch/arm/dts/Makefile | 2 + arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi | 131 +++++ arch/arm/dts/imx8mm-cl-iot-gate.dts | 550 ++++++++++++++++++++ 3 files changed, 683 insertions(+) create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate.dtsarch/arm/dts/Makefile +2
-0@@ -1003,6 +1003,8 @@ dtb-$(CONFIG_TARGET_DURIAN) += phytium-durian.dtb dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb +dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE) += imx8mm-cl-iot-gate.dtb + targets += $(dtb-y) # Add any required device tree compiler flags herearch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi new file +131
-0@@ -0,0 +1,131 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright 2019 NXP + */ + +/ { + wdt-reboot { + compatible = "wdt-reboot"; + wdt = <&wdog1>; + u-boot,dm-spl; + }; +}; + +&{/soc at 0} { + u-boot,dm-pre-reloc; + u-boot,dm-spl; +}; + +&clk { + u-boot,dm-spl; + u-boot,dm-pre-reloc; + /delete-property/ assigned-clocks; + /delete-property/ assigned-clock-parents; + /delete-property/ assigned-clock-rates; +}; + +&osc_24m { + u-boot,dm-spl; + u-boot,dm-pre-reloc; +}; + +&aips1 { + u-boot,dm-spl; + u-boot,dm-pre-reloc; +}; + +&aips2 { + u-boot,dm-spl; +}; + +&aips3 { + u-boot,dm-spl; +}; + +&iomuxc { + u-boot,dm-spl; +}; + +&pinctrl_reg_usdhc2_vmmc { + u-boot,dm-spl; +}; + +&pinctrl_uart3 { + u-boot,dm-spl; +}; + +&pinctrl_usdhc2_gpio { + u-boot,dm-spl; +}; + +&pinctrl_usdhc2 { + u-boot,dm-spl; +}; + +&pinctrl_usdhc3 { + u-boot,dm-spl; +}; + +&gpio1 { + u-boot,dm-spl; +}; + +&gpio2 { + u-boot,dm-spl; +}; + +&gpio3 { + u-boot,dm-spl; +}; + +&gpio4 { + u-boot,dm-spl; +}; + +&gpio5 { + u-boot,dm-spl; +}; + +&uart3 { + u-boot,dm-spl; +}; + +&usdhc1 { + u-boot,dm-spl; +}; + +&usdhc2 { + u-boot,dm-spl; +}; + +&usdhc3 { + u-boot,dm-spl; +}; + +&i2c2 { + u-boot,dm-spl; +}; + +&{/soc at 0/bus at 30800000/i2c at 30a30000/pmic at 4b} { + u-boot,dm-spl; +}; + +&{/soc at 0/bus at 30800000/i2c at 30a30000/pmic at 4b/regulators} { + u-boot,dm-spl; +}; + +&pinctrl_i2c2 { + u-boot,dm-spl; +}; + +&pinctrl_pmic { + u-boot,dm-spl; +}; + +&fec1 { + phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; +}; + +&wdog1 { + u-boot,dm-spl; +};arch/arm/dts/imx8mm-cl-iot-gate.dts new file +550
-1@@ -0,0 +1,550 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2019 NXP + */ + +/dts-v1/; + +#include <dt-bindings/usb/pd.h> +#include "imx8mm.dtsi" + +/ { + model = "CompuLab IOT-GATE-iMX8"; + compatible = "sb-iotgimx8", "cpl,ucm-imx8m-mini", "fsl,imx8mm-evk", "fsl,imx8mm"; + + chosen { + bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200"; + stdout-path = &uart3; + }; + + reg_vusb_5v: regulator-usdhc2 { + compatible = "regulator-fixed"; + regulator-name = "VUSB_5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>; + regulator-boot-on; + enable-active-high; + }; + + reg_usdhc2_vqmmc: regulator-usdhc2_1v8 { + compatible = "regulator-fixed"; + regulator-name = "usdhc2_1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_usdhc2_vmmc: regulator-usdhc2-vmmc { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <100>; + off-on-delay-us = <12000>; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy at 0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + at803x,led-act-blind-workaround; + at803x,eee-okay; + at803x,vddio-1p8v; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic at 4b { + compatible = "rohm,bd71837"; + reg = <0x4b>; + pinctrl-0 = <&pinctrl_pmic>; + gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>; + interrupt-parent = <&gpio1>; + interrupts = <3 GPIO_ACTIVE_LOW>; + + gpo { + rohm,drv = <0x0C>; /* 0b0000_1100 all gpos with cmos output mode */ + }; + + regulators { + bd71837,pmic-buck2-uses-i2c-dvs; + bd71837,pmic-buck2-dvs-voltage = <1000000>, + <900000>, + <0>; /* VDD_ARM: Run-Idle */ + buck1_reg: BUCK1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "BUCK2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck3_reg: BUCK3 { + regulator-name = "BUCK3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + }; + + buck4_reg: BUCK4 { + regulator-name = "BUCK4"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "BUCK5"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "BUCK6"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "BUCK7"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "BUCK8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "LDO1"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "LDO2"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "LDO3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "LDO4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "LDO6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "LDO7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + ptn5110: tcpc at 50 { + compatible = "nxp,ptn5110"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_typec1>; + reg = <0x50>; + interrupt-parent = <&gpio2>; + interrupts = <11 8>; + status = "okay"; + + port { + typec1_dr_sw: endpoint { + remote-endpoint = <&usb1_drd_sw>; + }; + }; + + typec1_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + power-role = "dual"; + data-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 20000, 3000)>; + op-sink-microwatt = <15000000>; + self-powered; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "disabled"; +}; + +&i2c4 {/* Expansion connector I2C */ + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + pca9555: gpio at 22 { + compatible = "nxp,pca9555"; + reg = <0x22>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart3 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "host"; + hnp-disable; + srp-disable; + adp-disable; + usb-role-switch; + vbus-supply = <®_vusb_5v>; + status = "okay"; + + port { + usb1_drd_sw: endpoint { + remote-endpoint = <&typec1_dr_sw>; + }; + }; +}; + +&usbotg2 { + dr_mode = "host"; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + fsl,wp-controller; + vmmc-supply = <®_usdhc2_vmmc>; + no-1-8-v; + mmc-ddr-1_8v; + non-removable; + vqmmc-supply = <®_usdhc2_vqmmc>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* USB VBUS enable GPIO */ + MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x00 + >; + }; + + pinctrl_hog_1: hoggrp-1 { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x19 + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x140 + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x140 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19 + >; + }; + + pinctrl_flexspi0: flexspi0grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c4 + MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x84 + MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x84 + MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x84 + MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x84 + MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x84 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicirq { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_typec1: typec1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 + >; + }; + + pinctrl_uart3: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B 0x49 + MX8MM_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX 0x49 + MX8MM_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B 0x49 + MX8MM_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX 0x49 + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2grpgpio { + fsl,pins = < + MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x40000196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; + --2.29.2
PATCH v3 2/2 arm: imx8m: add support for Compulab iot-gate-imx8 (imx8mm-cl-iot-gate)
In reply to Ying-Chun LiuFrom: "Ying-Chun Liu (PaulLiu)" <[email protected]>
Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate). The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console
--- arch/arm/mach-imx/imx8m/Kconfig | 8 + board/compulab/imx8mm-cl-iot-gate/Kconfig | 12 + board/compulab/imx8mm-cl-iot-gate/MAINTAINERS | 6 + board/compulab/imx8mm-cl-iot-gate/Makefile | 13 + .../compulab/imx8mm-cl-iot-gate/ddr/Makefile | 8 + board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c | 211 ++ board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h | 26 + .../ddr/lpddr4_timing_01061010.1_2.c | 1848 +++++++++++++++++ .../ddr/lpddr4_timing_01061010.c | 1847 ++++++++++++++++ .../ddr/lpddr4_timing_ff000110.c | 1847 ++++++++++++++++ .../ddr/lpddr4_timing_ff020008.c | 1847 ++++++++++++++++ .../imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c | 69 + board/compulab/imx8mm-cl-iot-gate/spl.c | 187 ++ configs/imx8mm-cl-iot-gate_defconfig | 130 ++ include/configs/imx8mm-cl-iot-gate.h | 190 ++ 15 files changed, 8249 insertions(+) create mode 100644 board/compulab/imx8mm-cl-iot-gate/Kconfig create mode 100644 board/compulab/imx8mm-cl-iot-gate/MAINTAINERS create mode 100644 board/compulab/imx8mm-cl-iot-gate/Makefile create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/Makefile create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.1_2.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff000110.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff020008.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c create mode 100644 board/compulab/imx8mm-cl-iot-gate/spl.c create mode 100644 configs/imx8mm-cl-iot-gate_defconfig create mode 100644 include/configs/imx8mm-cl-iot-gate.h
arch/arm/mach-imx/imx8m/Kconfig +8 -0
@@ -77,6 +77,13 @@ config TARGET_PHYCORE_IMX8MM select IMX8MM select SUPPORT_SPL select IMX8M_LPDDR4 + +config TARGET_IMX8MM_CL_IOT_GATE + bool "CompuLab iot-gate-imx8" + select IMX8MM + select SUPPORT_SPL + select IMX8M_LPDDR4 + endchoice source "board/freescale/imx8mq_evk/Kconfig"
@@ -88,5 +95,6 @@ source "board/technexion/pico-imx8mq/Kconfig" source "board/toradex/verdin-imx8mm/Kconfig" source "board/beacon/imx8mm/Kconfig" source "board/phytec/phycore_imx8mm/Kconfig" +source "board/compulab/imx8mm-cl-iot-gate/Kconfig" endif
board/compulab/imx8mm-cl-iot-gate/Kconfig new file +12 -0
@@ -0,0 +1,12 @@ +if TARGET_IMX8MM_CL_IOT_GATE + +config SYS_BOARD + default "imx8mm-cl-iot-gate" + +config SYS_VENDOR + default "compulab" + +config SYS_CONFIG_NAME + default "imx8mm-cl-iot-gate" + +endif
board/compulab/imx8mm-cl-iot-gate/MAINTAINERS new file +6 -0
@@ -0,0 +1,6 @@ +Compulab IOT-GATE-iMX8 BOARD +M: Ying-Chun Liu (PaulLiu) <[email protected]> +S: Maintained +F: board/compulab/imx8mm-cl-iot-gate/ +F: include/configs/imx8mm-cl-iot-gate.h +F: configs/imx8mm-cl-iot-gate_defconfig
board/compulab/imx8mm-cl-iot-gate/Makefile new file +13 -0
@@ -0,0 +1,13 @@ +# +# Copyright 2018 NXP +# Copyright 2020 Linaro +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += imx8mm-cl-iot-gate.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-y += ddr/ +endif
board/compulab/imx8mm-cl-iot-gate/ddr/Makefile new file +8 -0
@@ -0,0 +1,8 @@ +obj-y += ddr.o +obj-y += lpddr4_timing_ff020008.o +obj-y += lpddr4_timing_ff000110.o +ifdef CONFIG_TARGET_MCM_IMX8M_MINI +obj-y += lpddr4_timing_01061010.o +else +obj-y += lpddr4_timing_01061010.1_2.o +endif
board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c new file +211 -0
211 lines not on this page · raw message
board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h new file +26 -0
@@ -0,0 +1,26 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright 2017 NXP +* Copyright 2020 Linaro +* +*/ + +#ifndef __COMPULAB_DDR_H__ +#define __COMPULAB_DDR_H__ + +extern struct dram_timing_info ucm_dram_timing_ff020008; +extern struct dram_timing_info ucm_dram_timing_ff000110; +extern struct dram_timing_info ucm_dram_timing_01061010; + +void spl_dram_init_compulab (void ); + +#define TCM_DATA_CFG 0x7e0000 + +struct lpddr4_tcm_desc { +unsigned int size; +unsigned int sign; +unsigned int index; +unsigned int count; +}; + +#endif
board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.1_2.c new file +1848 -0
1,848 lines not on this page · raw message
board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.c new file +1847 -0
857 lines not on this page · raw message
board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff000110.c new file +1847 -0
1,847 lines not on this page · raw message
board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff020008.c new file +1847 -0
1,847 lines not on this page · raw message
board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c new file +69 -0
69 lines not on this page · raw message
board/compulab/imx8mm-cl-iot-gate/spl.c new file +187 -0
187 lines not on this page · raw message
configs/imx8mm-cl-iot-gate_defconfig new file +130 -0
130 lines not on this page · raw message
include/configs/imx8mm-cl-iot-gate.h new file +190 -0
190 lines not on this page · raw message
The rest of this diff is not shown. View the raw message.
Signature · 1 line
2.29.2
Part of the diff is not shown here. View the raw message.