Skip to contentSkip to conversation

add support for Compulab iot-gate-imx8

PATCH Superseded Ying-Chun Liu 2 participants 4 messages Dec 6, 2020

Subsystems (3)

v3 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#0 lore raw

v3 cover add support for Compulab iot-gate-imx8

From: "Ying-Chun Liu (PaulLiu)" <[email protected]>

Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate). The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console

Ying-Chun Liu (PaulLiu) (2):
arm: dts: add imx8mm-cl-iot-gate dts file
arm: imx8m: add support for Compulab iot-gate-imx8

    (imx8mm-cl-iot-gate)
 arch/arm/dts/Makefile                         |    2 +
 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi   |  131 ++
 arch/arm/dts/imx8mm-cl-iot-gate.dts           |  550 +++++
 arch/arm/mach-imx/imx8m/Kconfig               |    8 +
 board/compulab/imx8mm-cl-iot-gate/Kconfig     |   12 +
 board/compulab/imx8mm-cl-iot-gate/MAINTAINERS |    6 +
 board/compulab/imx8mm-cl-iot-gate/Makefile    |   13 +
 .../compulab/imx8mm-cl-iot-gate/ddr/Makefile  |    8 +
 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c   |  211 ++
 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h   |   26 +
 .../ddr/lpddr4_timing_01061010.1_2.c          | 1848 +++++++++++++++++
 .../ddr/lpddr4_timing_01061010.c              | 1847 ++++++++++++++++
 .../ddr/lpddr4_timing_ff000110.c              | 1847 ++++++++++++++++
 .../ddr/lpddr4_timing_ff020008.c              | 1847 ++++++++++++++++
 .../imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c   |   69 +
 board/compulab/imx8mm-cl-iot-gate/spl.c       |  187 ++
 configs/imx8mm-cl-iot-gate_defconfig          |  130 ++
 include/configs/imx8mm-cl-iot-gate.h          |  190 ++
 18 files changed, 8932 insertions(+)
 create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate.dts
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/Kconfig
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/MAINTAINERS
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/Makefile
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/Makefile
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.1_2.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff000110.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff020008.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/spl.c
 create mode 100644 configs/imx8mm-cl-iot-gate_defconfig
 create mode 100644 include/configs/imx8mm-cl-iot-gate.h
Signature · 1 line
2.29.2
#1 lore raw

PATCH v3 1/2 arm: dts: add imx8mm-cl-iot-gate dts file

From: "Ying-Chun Liu (PaulLiu)" <[email protected]>

Add board dts for imx8mm-cl-iot-gate

---
 arch/arm/dts/Makefile                       |   2 +
 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi | 131 +++++
 arch/arm/dts/imx8mm-cl-iot-gate.dts         | 550 ++++++++++++++++++++
 3 files changed, 683 insertions(+)
 create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate.dts
arch/arm/dts/Makefile +2 -0
index e2e8a5fb7a..d00ecb88e0 100644
@@ -1003,6 +1003,8 @@ dtb-$(CONFIG_TARGET_DURIAN) += phytium-durian.dtb
 
 dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb
 
+dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE) += imx8mm-cl-iot-gate.dtb
+
 targets += $(dtb-y)
 
 # Add any required device tree compiler flags here
arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi new file +131 -0

131 lines not on this page · raw message

arch/arm/dts/imx8mm-cl-iot-gate.dts new file +550 -0

550 lines not on this page · raw message

Signature · 1 line
2.29.2
#2 lore raw

PATCH v3 1/2 arm: dts: add imx8mm-cl-iot-gate dts file

Quoted 11 lines · Ying-Chun Liu

From: "Ying-Chun Liu (PaulLiu)" <[email protected]>

Add board dts for imx8mm-cl-iot-gate

---

What's changed since the last version. You should put a change log at this point.

Quoted 716 lines
 arch/arm/dts/Makefile                       |   2 +
 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi | 131 +++++
 arch/arm/dts/imx8mm-cl-iot-gate.dts         | 550 ++++++++++++++++++++
 3 files changed, 683 insertions(+)
 create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi
 create mode 100644 arch/arm/dts/imx8mm-cl-iot-gate.dts
arch/arm/dts/Makefile +2 -0
index e2e8a5fb7a..d00ecb88e0 100644
@@ -1003,6 +1003,8 @@ dtb-$(CONFIG_TARGET_DURIAN) += phytium-durian.dtb
 
 dtb-$(CONFIG_TARGET_PRESIDIO_ASIC) += ca-presidio-engboard.dtb
 
+dtb-$(CONFIG_TARGET_IMX8MM_CL_IOT_GATE) += imx8mm-cl-iot-gate.dtb
+
 targets += $(dtb-y)
 
 # Add any required device tree compiler flags here
arch/arm/dts/imx8mm-cl-iot-gate-u-boot.dtsi new file +131 -0
new file mode 100644
index 0000000000..a36147eb11
@@ -0,0 +1,131 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+/ {
+       wdt-reboot {
+               compatible = "wdt-reboot";
+               wdt = <&wdog1>;
+               u-boot,dm-spl;
+       };
+};
+
+&{/soc at 0} {
+       u-boot,dm-pre-reloc;
+       u-boot,dm-spl;
+};
+
+&clk {
+       u-boot,dm-spl;
+       u-boot,dm-pre-reloc;
+       /delete-property/ assigned-clocks;
+       /delete-property/ assigned-clock-parents;
+       /delete-property/ assigned-clock-rates;
+};
+
+&osc_24m {
+       u-boot,dm-spl;
+       u-boot,dm-pre-reloc;
+};
+
+&aips1 {
+       u-boot,dm-spl;
+       u-boot,dm-pre-reloc;
+};
+
+&aips2 {
+       u-boot,dm-spl;
+};
+
+&aips3 {
+       u-boot,dm-spl;
+};
+
+&iomuxc {
+       u-boot,dm-spl;
+};
+
+&pinctrl_reg_usdhc2_vmmc {
+       u-boot,dm-spl;
+};
+
+&pinctrl_uart3 {
+       u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2_gpio {
+       u-boot,dm-spl;
+};
+
+&pinctrl_usdhc2 {
+       u-boot,dm-spl;
+};
+
+&pinctrl_usdhc3 {
+       u-boot,dm-spl;
+};
+
+&gpio1 {
+       u-boot,dm-spl;
+};
+
+&gpio2 {
+       u-boot,dm-spl;
+};
+
+&gpio3 {
+       u-boot,dm-spl;
+};
+
+&gpio4 {
+       u-boot,dm-spl;
+};
+
+&gpio5 {
+       u-boot,dm-spl;
+};
+
+&uart3 {
+       u-boot,dm-spl;
+};
+
+&usdhc1 {
+       u-boot,dm-spl;
+};
+
+&usdhc2 {
+       u-boot,dm-spl;
+};
+
+&usdhc3 {
+       u-boot,dm-spl;
+};
+
+&i2c2 {
+       u-boot,dm-spl;
+};
+
+&{/soc at 0/bus at 30800000/i2c at 30a30000/pmic at 4b} {
+       u-boot,dm-spl;
+};
+
+&{/soc at 0/bus at 30800000/i2c at 30a30000/pmic at 4b/regulators} {
+       u-boot,dm-spl;
+};
+
+&pinctrl_i2c2 {
+       u-boot,dm-spl;
+};
+
+&pinctrl_pmic {
+       u-boot,dm-spl;
+};
+
+&fec1 {
+       phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+};
+
+&wdog1 {
+       u-boot,dm-spl;
+};
arch/arm/dts/imx8mm-cl-iot-gate.dts new file +550 -1
new file mode 100644
index 0000000000..82e9c0f40b
@@ -0,0 +1,550 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/usb/pd.h>
+#include "imx8mm.dtsi"
+
+/ {
+       model = "CompuLab IOT-GATE-iMX8";
+       compatible = "sb-iotgimx8", "cpl,ucm-imx8m-mini", "fsl,imx8mm-evk", "fsl,imx8mm";
+
+       chosen {
+               bootargs = "console=ttymxc2,115200 earlycon=ec_imx6q,0x30880000,115200";
+               stdout-path = &uart3;
+       };
+
+       reg_vusb_5v: regulator-usdhc2 {
+               compatible = "regulator-fixed";
+               regulator-name = "VUSB_5V";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+               regulator-boot-on;
+               enable-active-high;
+       };
+
+       reg_usdhc2_vqmmc: regulator-usdhc2_1v8 {
+               compatible = "regulator-fixed";
+               regulator-name = "usdhc2_1v8";
+               regulator-min-microvolt = <1800000>;
+               regulator-max-microvolt = <1800000>;
+               regulator-always-on;
+       };
+
+       reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+               compatible = "regulator-fixed";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+               regulator-name = "VSD_3V3";
+               regulator-min-microvolt = <3300000>;
+               regulator-max-microvolt = <3300000>;
+               gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+               enable-active-high;
+               startup-delay-us = <100>;
+               off-on-delay-us = <12000>;
+       };
+};
+
+&A53_0 {
+       cpu-supply = <&buck2_reg>;
+};
+
+&fec1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_fec1>;
+       phy-mode = "rgmii-id";
+       phy-handle = <&ethphy0>;
+       fsl,magic-packet;
+       status = "okay";
+
+       mdio {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               ethphy0: ethernet-phy at 0 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <0>;
+                       at803x,led-act-blind-workaround;
+                       at803x,eee-okay;
+                       at803x,vddio-1p8v;
+               };
+       };
+};
+
+&i2c1 {
+       clock-frequency = <400000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c1>;
+       status = "okay";
+};
+
+&i2c2 {
+       clock-frequency = <400000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c2>;
+       status = "okay";
+
+       pmic at 4b {
+               compatible = "rohm,bd71837";
+               reg = <0x4b>;
+               pinctrl-0 = <&pinctrl_pmic>;
+               gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
+               interrupt-parent = <&gpio1>;
+               interrupts = <3 GPIO_ACTIVE_LOW>;
+
+               gpo {
+                       rohm,drv = <0x0C>;      /* 0b0000_1100 all gpos with cmos output mode */
+               };
+
+               regulators {
+                       bd71837,pmic-buck2-uses-i2c-dvs;
+                       bd71837,pmic-buck2-dvs-voltage = <1000000>,
+                               <900000>,
+                               <0>; /* VDD_ARM: Run-Idle */
+                       buck1_reg: BUCK1 {
+                               regulator-name = "BUCK1";
+                               regulator-min-microvolt = <700000>;
+                               regulator-max-microvolt = <1300000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-ramp-delay = <1250>;
+                       };
+
+                       buck2_reg: BUCK2 {
+                               regulator-name = "BUCK2";
+                               regulator-min-microvolt = <700000>;
+                               regulator-max-microvolt = <1300000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                               regulator-ramp-delay = <1250>;
+                       };
+
+                       buck3_reg: BUCK3 {
+                               regulator-name = "BUCK3";
+                               regulator-min-microvolt = <700000>;
+                               regulator-max-microvolt = <1350000>;
+                       };
+
+                       buck4_reg: BUCK4 {
+                               regulator-name = "BUCK4";
+                               regulator-min-microvolt = <700000>;
+                               regulator-max-microvolt = <1350000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       buck5_reg: BUCK5 {
+                               regulator-name = "BUCK5";
+                               regulator-min-microvolt = <700000>;
+                               regulator-max-microvolt = <1350000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       buck6_reg: BUCK6 {
+                               regulator-name = "BUCK6";
+                               regulator-min-microvolt = <3000000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       buck7_reg: BUCK7 {
+                               regulator-name = "BUCK7";
+                               regulator-min-microvolt = <1605000>;
+                               regulator-max-microvolt = <1995000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       buck8_reg: BUCK8 {
+                               regulator-name = "BUCK8";
+                               regulator-min-microvolt = <800000>;
+                               regulator-max-microvolt = <1400000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo1_reg: LDO1 {
+                               regulator-name = "LDO1";
+                               regulator-min-microvolt = <3000000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo2_reg: LDO2 {
+                               regulator-name = "LDO2";
+                               regulator-min-microvolt = <900000>;
+                               regulator-max-microvolt = <900000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo3_reg: LDO3 {
+                               regulator-name = "LDO3";
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo4_reg: LDO4 {
+                               regulator-name = "LDO4";
+                               regulator-min-microvolt = <900000>;
+                               regulator-max-microvolt = <1800000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo5_reg: LDO5 {
+                               regulator-name = "LDO5";
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <3300000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo6_reg: LDO6 {
+                               regulator-name = "LDO6";
+                               regulator-min-microvolt = <900000>;
+                               regulator-max-microvolt = <1800000>;
+                               regulator-boot-on;
+                               regulator-always-on;
+                       };
+
+                       ldo7_reg: LDO7 {
+                               regulator-name = "LDO7";
+                               regulator-min-microvolt = <1800000>;
+                               regulator-max-microvolt = <3300000>;
+                       };
+               };
+       };
+
+       ptn5110: tcpc at 50 {
+               compatible = "nxp,ptn5110";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pinctrl_typec1>;
+               reg = <0x50>;
+               interrupt-parent = <&gpio2>;
+               interrupts = <11 8>;
+               status = "okay";
+
+               port {
+                       typec1_dr_sw: endpoint {
+                               remote-endpoint = <&usb1_drd_sw>;
+                       };
+               };
+
+               typec1_con: connector {
+                       compatible = "usb-c-connector";
+                       label = "USB-C";
+                       power-role = "dual";
+                       data-role = "dual";
+                       try-power-role = "sink";
+                       source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+                       sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+                                    PDO_VAR(5000, 20000, 3000)>;
+                       op-sink-microwatt = <15000000>;
+                       self-powered;
+               };
+       };
+};
+
+&i2c3 {
+       clock-frequency = <400000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c3>;
+       status = "disabled";
+};
+
+&i2c4 {/* Expansion connector I2C */
+       clock-frequency = <100000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_i2c4>;
+       status = "okay";
+
+       pca9555: gpio at 22 {
+               compatible = "nxp,pca9555";
+               reg = <0x22>;
+               gpio-controller;
+               #gpio-cells = <2>;
+       };
+};
+
+&snvs_pwrkey {
+       status = "okay";
+};
+
+&uart3 { /* console */
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_uart3>;
+       status = "okay";
+};
+
+&usbotg1 {
+       dr_mode = "host";
+       hnp-disable;
+       srp-disable;
+       adp-disable;
+       usb-role-switch;
+       vbus-supply = <&reg_vusb_5v>;
+       status = "okay";
+
+       port {
+               usb1_drd_sw: endpoint {
+                       remote-endpoint = <&typec1_dr_sw>;
+               };
+       };
+};
+
+&usbotg2 {
+       dr_mode = "host";
+       status = "okay";
+};
+
+&usdhc2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+       pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+       pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+       cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+       bus-width = <4>;
+       fsl,wp-controller;
+       vmmc-supply = <&reg_usdhc2_vmmc>;
+       no-1-8-v;
+       mmc-ddr-1_8v;
+       non-removable;
+       vqmmc-supply = <&reg_usdhc2_vqmmc>;
+       status = "okay";
+};
+
+&usdhc3 {
+       pinctrl-names = "default", "state_100mhz", "state_200mhz";
+       pinctrl-0 = <&pinctrl_usdhc3>;
+       pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+       pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+       bus-width = <8>;
+       non-removable;
+       status = "okay";
+};
+
+&wdog1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pinctrl_wdog>;
+       fsl,ext-reset-output;
+       status = "okay";
+};
+
+&iomuxc {
+       pinctrl-names = "default";
+
+       pinctrl_hog: hoggrp {
+               fsl,pins = <
+                       /* USB VBUS enable GPIO */
+                       MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28               0x00
+               >;
+       };
+
+       pinctrl_hog_1: hoggrp-1 {
+               fsl,pins = <
+                       MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8               0x19
+                       MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0               0x140
+                       MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15              0x140
+               >;
+       };
+
+       pinctrl_fec1: fec1grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_ENET_MDC_ENET1_MDC                 0x3
+                       MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO               0x3
+                       MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3           0x1f
+                       MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2           0x1f
+                       MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1           0x1f
+                       MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0           0x1f
+                       MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3           0x91
+                       MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2           0x91
+                       MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1           0x91
+                       MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0           0x91
+                       MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC           0x1f
+                       MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC           0x91
+                       MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL     0x91
+                       MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL     0x1f
+                       MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22                0x19
+               >;
+       };
+
+       pinctrl_flexspi0: flexspi0grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK       0x1c4
+                       MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B    0x84
+                       MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0   0x84
+                       MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1   0x84
+                       MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2   0x84
+                       MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3   0x84
+               >;
+       };
+
+       pinctrl_i2c1: i2c1grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL                  0x400001c3
+                       MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA                  0x400001c3
+               >;
+       };
+
+       pinctrl_i2c2: i2c2grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL                  0x400001c3
+                       MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA                  0x400001c3
+               >;
+       };
+
+       pinctrl_i2c3: i2c3grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL                  0x400001c3
+                       MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA                  0x400001c3
+               >;
+       };
+
+       pinctrl_i2c4: i2c4grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL                  0x400001c3
+                       MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA                  0x400001c3
+               >;
+       };
+
+       pinctrl_pmic: pmicirq {
+               fsl,pins = <
+                       MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3               0x41
+               >;
+       };
+
+       pinctrl_typec1: typec1grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11      0x159
+               >;
+       };
+
+       pinctrl_uart3: uart1grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX             0x49
+                       MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX             0x49
+               >;
+       };
+
+       pinctrl_uart4: uart4grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_ECSPI2_MISO_UART4_DCE_CTS_B        0x49
+                       MX8MM_IOMUXC_ECSPI2_MOSI_UART4_DCE_TX           0x49
+                       MX8MM_IOMUXC_ECSPI2_SS0_UART4_DCE_RTS_B         0x49
+                       MX8MM_IOMUXC_ECSPI2_SCLK_UART4_DCE_RX           0x49
+               >;
+       };
+
+       pinctrl_reg_usdhc2_vmmc: regusdhc2vmmc {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19     0x41
+               >;
+       };
+
+       pinctrl_usdhc2_gpio: usdhc2grpgpio {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19     0x41
+               >;
+       };
+
+       pinctrl_usdhc2: usdhc2grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x190
+                       MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d0
+                       MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d0
+                       MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d0
+                       MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d0
+                       MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d0
+                       MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
+               >;
+       };
+
+       pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x194
+                       MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d4
+                       MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d4
+                       MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d4
+                       MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d4
+                       MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d4
+                       MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
+               >;
+       };
+
+       pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+               fsl,pins = <
+                       MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK         0x196
+                       MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD         0x1d6
+                       MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0     0x1d6
+                       MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1     0x1d6
+                       MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2     0x1d6
+                       MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3     0x1d6
+                       MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
+               >;
+       };
+
+       pinctrl_usdhc3: usdhc3grp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK               0x40000190
+                       MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD               0x1d0
+                       MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0           0x1d0
+                       MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1           0x1d0
+                       MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2           0x1d0
+                       MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3           0x1d0
+                       MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4             0x1d0
+                       MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5            0x1d0
+                       MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6            0x1d0
+                       MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7              0x1d0
+                       MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE           0x190
+               >;
+       };
+
+       pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+               fsl,pins = <
+                       MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK               0x40000194
+                       MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD               0x1d4
+                       MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0           0x1d4
+                       MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1           0x1d4
+                       MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2           0x1d4
+                       MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3           0x1d4
+                       MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4             0x1d4
+                       MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5            0x1d4
+                       MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6            0x1d4
+                       MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7              0x1d4
+                       MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE           0x194
+               >;
+       };
+
+       pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+               fsl,pins = <
+                       MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK               0x40000196
+                       MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD               0x1d6
+                       MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0           0x1d6
+                       MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1           0x1d6
+                       MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2           0x1d6
+                       MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3           0x1d6
+                       MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4             0x1d6
+                       MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5            0x1d6
+                       MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6            0x1d6
+                       MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7              0x1d6
+                       MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE           0x196
+               >;
+       };
+
+       pinctrl_wdog: wdoggrp {
+               fsl,pins = <
+                       MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B    0xc6
+               >;
+       };
+};
+
--

2.29.2

#3 lore raw

PATCH v3 2/2 arm: imx8m: add support for Compulab iot-gate-imx8 (imx8mm-cl-iot-gate)

In reply to Ying-Chun Liu

From: "Ying-Chun Liu (PaulLiu)" <[email protected]>

Add initial support for Compulab iot-gate-imx8 board (imx8mm-cl-iot-gate). The initial support includes:
- MMC
- eMMC
- I2C
- FEC
- Serial console

---
 arch/arm/mach-imx/imx8m/Kconfig               |    8 +
 board/compulab/imx8mm-cl-iot-gate/Kconfig     |   12 +
 board/compulab/imx8mm-cl-iot-gate/MAINTAINERS |    6 +
 board/compulab/imx8mm-cl-iot-gate/Makefile    |   13 +
 .../compulab/imx8mm-cl-iot-gate/ddr/Makefile  |    8 +
 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c   |  211 ++
 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h   |   26 +
 .../ddr/lpddr4_timing_01061010.1_2.c          | 1848 +++++++++++++++++
 .../ddr/lpddr4_timing_01061010.c              | 1847 ++++++++++++++++
 .../ddr/lpddr4_timing_ff000110.c              | 1847 ++++++++++++++++
 .../ddr/lpddr4_timing_ff020008.c              | 1847 ++++++++++++++++
 .../imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c   |   69 +
 board/compulab/imx8mm-cl-iot-gate/spl.c       |  187 ++
 configs/imx8mm-cl-iot-gate_defconfig          |  130 ++
 include/configs/imx8mm-cl-iot-gate.h          |  190 ++
 15 files changed, 8249 insertions(+)
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/Kconfig
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/MAINTAINERS
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/Makefile
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/Makefile
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.1_2.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff000110.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff020008.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c
 create mode 100644 board/compulab/imx8mm-cl-iot-gate/spl.c
 create mode 100644 configs/imx8mm-cl-iot-gate_defconfig
 create mode 100644 include/configs/imx8mm-cl-iot-gate.h
arch/arm/mach-imx/imx8m/Kconfig +8 -0
index 8615dc3bec..287a6f4616 100644
@@ -77,6 +77,13 @@ config TARGET_PHYCORE_IMX8MM
 	select IMX8MM
         select SUPPORT_SPL
 	select IMX8M_LPDDR4
+
+config TARGET_IMX8MM_CL_IOT_GATE
+	bool "CompuLab iot-gate-imx8"
+	select IMX8MM
+	select SUPPORT_SPL
+	select IMX8M_LPDDR4
+
 endchoice
 
 source "board/freescale/imx8mq_evk/Kconfig"
@@ -88,5 +95,6 @@ source "board/technexion/pico-imx8mq/Kconfig"
 source "board/toradex/verdin-imx8mm/Kconfig"
 source "board/beacon/imx8mm/Kconfig"
 source "board/phytec/phycore_imx8mm/Kconfig"
+source "board/compulab/imx8mm-cl-iot-gate/Kconfig"
 
 endif
board/compulab/imx8mm-cl-iot-gate/Kconfig new file +12 -0
new file mode 100644
index 0000000000..7f5c794bf5
@@ -0,0 +1,12 @@
+if TARGET_IMX8MM_CL_IOT_GATE
+
+config SYS_BOARD
+	default "imx8mm-cl-iot-gate"
+
+config SYS_VENDOR
+	default "compulab"
+
+config SYS_CONFIG_NAME
+	default "imx8mm-cl-iot-gate"
+
+endif
board/compulab/imx8mm-cl-iot-gate/MAINTAINERS new file +6 -0
new file mode 100644
index 0000000000..9c6b17095c
@@ -0,0 +1,6 @@
+Compulab IOT-GATE-iMX8 BOARD
+M:	Ying-Chun Liu (PaulLiu) <[email protected]>
+S:	Maintained
+F:	board/compulab/imx8mm-cl-iot-gate/
+F:	include/configs/imx8mm-cl-iot-gate.h
+F:	configs/imx8mm-cl-iot-gate_defconfig
board/compulab/imx8mm-cl-iot-gate/Makefile new file +13 -0
new file mode 100644
index 0000000000..3a2bfc4dc4
@@ -0,0 +1,13 @@
+#
+# Copyright 2018 NXP
+# Copyright 2020 Linaro
+#
+# SPDX-License-Identifier:      GPL-2.0+
+#
+
+obj-y += imx8mm-cl-iot-gate.o
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+obj-y += ddr/
+endif
board/compulab/imx8mm-cl-iot-gate/ddr/Makefile new file +8 -0
new file mode 100644
index 0000000000..5914796628
@@ -0,0 +1,8 @@
+obj-y += ddr.o
+obj-y += lpddr4_timing_ff020008.o
+obj-y += lpddr4_timing_ff000110.o
+ifdef CONFIG_TARGET_MCM_IMX8M_MINI
+obj-y += lpddr4_timing_01061010.o
+else
+obj-y += lpddr4_timing_01061010.1_2.o
+endif
board/compulab/imx8mm-cl-iot-gate/ddr/ddr.c new file +211 -0

211 lines not on this page · raw message

board/compulab/imx8mm-cl-iot-gate/ddr/ddr.h new file +26 -0
new file mode 100644
index 0000000000..59c1891159
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2017 NXP
+ * Copyright 2020 Linaro
+ *
+ */
+
+#ifndef __COMPULAB_DDR_H__
+#define __COMPULAB_DDR_H__
+
+extern struct dram_timing_info ucm_dram_timing_ff020008;
+extern struct dram_timing_info ucm_dram_timing_ff000110;
+extern struct dram_timing_info ucm_dram_timing_01061010;
+
+void spl_dram_init_compulab(void);
+
+#define TCM_DATA_CFG 0x7e0000
+
+struct lpddr4_tcm_desc {
+	unsigned int size;
+	unsigned int sign;
+	unsigned int index;
+	unsigned int count;
+};
+
+#endif
board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.1_2.c new file +1848 -0

1,848 lines not on this page · raw message

board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_01061010.c new file +1847 -0

857 lines not on this page · raw message

board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff000110.c new file +1847 -0

1,847 lines not on this page · raw message

board/compulab/imx8mm-cl-iot-gate/ddr/lpddr4_timing_ff020008.c new file +1847 -0

1,847 lines not on this page · raw message

board/compulab/imx8mm-cl-iot-gate/imx8mm-cl-iot-gate.c new file +69 -0

69 lines not on this page · raw message

board/compulab/imx8mm-cl-iot-gate/spl.c new file +187 -0

187 lines not on this page · raw message

configs/imx8mm-cl-iot-gate_defconfig new file +130 -0

130 lines not on this page · raw message

include/configs/imx8mm-cl-iot-gate.h new file +190 -0

190 lines not on this page · raw message

The rest of this diff is not shown. View the raw message.

Signature · 1 line
2.29.2

Part of the diff is not shown here. View the raw message.