ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2
Subsystems (2)
PATCH v2 1/1 ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2
From: Mans Rullgard <[email protected]>
Add pinmux setting for USB1 overcurrent on pwm2 pad.
---
Changes for v2:
- Add S-o-B
--- arch/arm/boot/dts/imx28.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm/boot/dts/imx28.dtsi +10 -0
@@ -948,6 +948,16 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; + usb1_pins_b: usb1@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_PWM2__USB1_OVERCURRENT + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + usb0_id_pins_a: usb0id@0 { reg = <0>; fsl,pinmux-ids = <
Signature · 1 line
2.20.1
Hi Shawn,
Quoted 4 lines
From: Mans Rullgard <[email protected]>
Add pinmux setting for USB1 overcurrent on pwm2 pad.
Gentle ping on this patch.
Quoted 29 lines
Signed-off-by Mans Rullgard <[email protected]>Signed-off-by Lukasz Majewski <[email protected]>---
Changes for v2:
- Add S-o-B--- arch/arm/boot/dts/imx28.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)(quoted diff) +0
-0
b/arch/arm/boot/dts/imx28.dtsiindexbbe52150b165..84d0176d5193100644arch/arm/boot/dts/imx28.dtsi +4
-0@@ -948,6 +948,16 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; + usb1_pins_b: usb1@1 { + reg = <1>; + fsl,pinmux-ids = < +
MX28_PAD_PWM2__USB1_OVERCURRENTarch/arm/boot/dts/imx28.dtsi +2
-0+ >; + fsl,drive-strength =<
MXS_DRIVE_12mA>;arch/arm/boot/dts/imx28.dtsi +1
-0+ fsl,voltage =<
MXS_VOLTAGE_HIGH>;arch/arm/boot/dts/imx28.dtsi +1
-0+ fsl,pull-up =<
MXS_PULL_DISABLE>;
arch/arm/boot/dts/imx28.dtsi line 963
Quoted 5 lines
arch/arm/boot/dts/imx28.dtsi +2
-0+ }; + usb0_id_pins_a: usb0id@0 { reg = <0>; fsl,pinmux-ids = <
Best regards,
Lukasz Majewski
--
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-59 Fax: (+49)-8142-66989-80 Email: [email protected]
Quoted 7 lines · Lukasz Majewski
From: Mans Rullgard <[email protected]>
Add pinmux setting for USB1 overcurrent on pwm2 pad.
Signed-off-by Mans Rullgard <[email protected]>Signed-off-by Lukasz Majewski <[email protected]>
Shawn Guo
AppliedQuoted 6 lines · Lukasz Majewski
From: Mans Rullgard <[email protected]>
Add pinmux setting for USB1 overcurrent on pwm2 pad.
Signed-off-by Mans Rullgard <[email protected]>Signed-off-by Lukasz Majewski <[email protected]>
Applied, thanks.