Couple improvements for Tegra clk driver

PATCH Superseded Dmitry Osipenko 1 participant 4 messages Dec 15, 2020

Subsystems (3)

Common clk Tegra architecture support Tegra clock driver

lore

Share & tools

lore

Dmitry Osipenko

author

2020-12-15 21:12 UTC #0 lore raw

cover Couple improvements for Tegra clk driver

This series fixes couple minor problems of the Tegra clk driver. Please review and apply, thanks in advance.

Dmitry Osipenko (3):
clk: tegra30: Use 300MHz for video decoder by default
clk: tegra: Fix refcounting of gate clocks
clk: tegra: Ensure that PLLU configuration is applied properly

 drivers/clk/tegra/clk-periph-gate.c | 72 +++++++++++++++++++----------
 drivers/clk/tegra/clk-periph.c      | 11 +++++
 drivers/clk/tegra/clk-pll.c         |  9 ++--
 drivers/clk/tegra/clk-tegra30.c     |  2 +-
 4 files changed, 63 insertions(+), 31 deletions(-)

Signature · 1 line

2.29.2

Dmitry Osipenko

author

2020-12-15 21:13 UTC #1 lore raw

PATCH 1/3 clk: tegra30: Use 300MHz for video decoder by default

The 600MHz is a too high clock rate for some SoC versions for the video decoder hardware and this may cause stability issues. Use 300MHz for the video decoder by default, which is supported by all hardware versions.

Fixes ed1a2459e20c ("clk: tegra: Add Tegra20/30 EMC clock implementation")

Signed-off-by Dmitry Osipenko <[email protected]>

---
 drivers/clk/tegra/clk-tegra30.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

drivers/clk/tegra/clk-tegra30.c +1 -1

index 37244a7e68c2..98923c4674bf 100644
@@ -1248,7 +1248,7 @@ static struct tegra_clk_init_table init_table[] __initdata = {
 	{ TEGRA30_CLK_GR3D, TEGRA30_CLK_PLL_C, 300000000, 0 },
 	{ TEGRA30_CLK_GR3D2, TEGRA30_CLK_PLL_C, 300000000, 0 },
 	{ TEGRA30_CLK_PLL_U, TEGRA30_CLK_CLK_MAX, 480000000, 0 },
-	{ TEGRA30_CLK_VDE, TEGRA30_CLK_PLL_C, 600000000, 0 },
+	{ TEGRA30_CLK_VDE, TEGRA30_CLK_PLL_C, 300000000, 0 },
 	{ TEGRA30_CLK_SPDIF_IN_SYNC, TEGRA30_CLK_CLK_MAX, 24000000, 0 },
 	{ TEGRA30_CLK_I2S0_SYNC, TEGRA30_CLK_CLK_MAX, 24000000, 0 },
 	{ TEGRA30_CLK_I2S1_SYNC, TEGRA30_CLK_CLK_MAX, 24000000, 0 },

Signature · 1 line

2.29.2

Dmitry Osipenko

author

2020-12-15 21:14 UTC #2 lore raw

PATCH 2/3 clk: tegra: Fix refcounting of gate clocks

In reply to Dmitry Osipenko

The refcounting of the gate clocks has a bug causing the enable_refcnt to underflow when unused clocks are disabled. This happens because clk provider erroneously bumps the refcount if clock is enabled at a boot time, which it shouldn't be doing, and it does this only for the gate clocks, while peripheral clocks are using the same gate ops and the peripheral clocks are missing the initial bump. Hence the refcount of the peripheral clocks is 0 when unused clocks are disabled and then the counter is decremented further by the gate ops, causing the integer underflow.

Fix this problem by removing the erroneous bump and by implementing the disable_unused() callback, which disables the unused gates properly.

The visible effect of the bug is such that the unused clocks are never gated if a loaded kernel module grabs the unused clocks and starts to use them. In practice this shouldn't cause any real problems for the drivers and boards supported by the kernel today.

Signed-off-by Dmitry Osipenko <[email protected]>

---
 drivers/clk/tegra/clk-periph-gate.c | 72 +++++++++++++++++++----------
 drivers/clk/tegra/clk-periph.c      | 11 +++++
 2 files changed, 58 insertions(+), 25 deletions(-)

drivers/clk/tegra/clk-periph-gate.c +47 ~~-25~~

index 4b31beefc9fc..3c4259fec82e 100644
@@ -48,18 +48,9 @@ static int clk_periph_is_enabled(struct clk_hw *hw)
 	return state;
 }
 
-static int clk_periph_enable(struct clk_hw *hw)
+static void clk_periph_enable_locked(struct clk_hw *hw)
 {
 	struct tegra_clk_periph_gate *gate = to_clk_periph_gate(hw);
-	unsigned long flags = 0;
-
-	spin_lock_irqsave(&periph_ref_lock, flags);
-
-	gate->enable_refcnt[gate->clk_num]++;
-	if (gate->enable_refcnt[gate->clk_num] > 1) {
-		spin_unlock_irqrestore(&periph_ref_lock, flags);
-		return 0;
-	}
 
 	write_enb_set(periph_clk_to_bit(gate), gate);
 	udelay(2);

@@ -78,6 +69,32 @@ static int clk_periph_enable(struct clk_hw *hw)
 		udelay(1);
 		writel_relaxed(0, gate->clk_base + LVL2_CLK_GATE_OVRE);
 	}
+}
+
+static void clk_periph_disable_locked(struct clk_hw *hw)
+{
+	struct tegra_clk_periph_gate *gate = to_clk_periph_gate(hw);
+
+	/*
+	 * If peripheral is in the APB bus then read the APB bus to
+	 * flush the write operation in apb bus. This will avoid the
+	 * peripheral access after disabling clock
+	 */
+	if (gate->flags & TEGRA_PERIPH_ON_APB)
+		tegra_read_chipid();
+
+	write_enb_clr(periph_clk_to_bit(gate), gate);
+}
+
+static int clk_periph_enable(struct clk_hw *hw)
+{
+	struct tegra_clk_periph_gate *gate = to_clk_periph_gate(hw);
+	unsigned long flags = 0;
+
+	spin_lock_irqsave(&periph_ref_lock, flags);
+
+	if (!gate->enable_refcnt[gate->clk_num]++)
+		clk_periph_enable_locked(hw);
 
 	spin_unlock_irqrestore(&periph_ref_lock, flags);

@@ -91,21 +108,28 @@ static void clk_periph_disable(struct clk_hw *hw)
 
 	spin_lock_irqsave(&periph_ref_lock, flags);
 
-	gate->enable_refcnt[gate->clk_num]--;
-	if (gate->enable_refcnt[gate->clk_num] > 0) {
-		spin_unlock_irqrestore(&periph_ref_lock, flags);
-		return;
-	}
+	WARN_ON(!gate->enable_refcnt[gate->clk_num]);
+
+	if (gate->enable_refcnt[gate->clk_num]-- == 1)
+		clk_periph_disable_locked(hw);
+
+	spin_unlock_irqrestore(&periph_ref_lock, flags);
+}
+
+static void clk_periph_disable_unused(struct clk_hw *hw)
+{
+	struct tegra_clk_periph_gate *gate = to_clk_periph_gate(hw);
+	unsigned long flags = 0;
+
+	spin_lock_irqsave(&periph_ref_lock, flags);
 
 	/*
-	 * If peripheral is in the APB bus then read the APB bus to
-	 * flush the write operation in apb bus. This will avoid the
-	 * peripheral access after disabling clock
+	 * Some clocks are duplicated and some of them are marked as critical,
+	 * like fuse and fuse_burn for example, thus the enable_refcnt will
+	 * be non-zero here id the "unused" duplicate is disabled by CCF.
 	 */
-	if (gate->flags & TEGRA_PERIPH_ON_APB)
-		tegra_read_chipid();
-
-	write_enb_clr(periph_clk_to_bit(gate), gate);
+	if (!gate->enable_refcnt[gate->clk_num])
+		clk_periph_disable_locked(hw);
 
 	spin_unlock_irqrestore(&periph_ref_lock, flags);
 }

@@ -114,6 +138,7 @@ const struct clk_ops tegra_clk_periph_gate_ops = {
 	.is_enabled = clk_periph_is_enabled,
 	.enable = clk_periph_enable,
 	.disable = clk_periph_disable,
+	.disable_unused = clk_periph_disable_unused,
 };
 
 struct clk *tegra_clk_register_periph_gate(const char *name,

@@ -148,9 +173,6 @@ struct clk *tegra_clk_register_periph_gate(const char *name,
 	gate->enable_refcnt = enable_refcnt;
 	gate->regs = pregs;
 
-	if (read_enb(gate) & periph_clk_to_bit(gate))
-		enable_refcnt[clk_num]++;
-
 	/* Data in .init is copied by clk_register(), so stack variable OK */
 	gate->hw.init = &init;

drivers/clk/tegra/clk-periph.c +11 -0

index 67620c7ecd9e..79ca3aa072b7 100644
@@ -100,6 +100,15 @@ static void clk_periph_disable(struct clk_hw *hw)
 	gate_ops->disable(gate_hw);
 }
 
+static void clk_periph_disable_unused(struct clk_hw *hw)
+{
+	struct tegra_clk_periph *periph = to_clk_periph(hw);
+	const struct clk_ops *gate_ops = periph->gate_ops;
+	struct clk_hw *gate_hw = &periph->gate.hw;
+
+	gate_ops->disable_unused(gate_hw);
+}
+
 static void clk_periph_restore_context(struct clk_hw *hw)
 {
 	struct tegra_clk_periph *periph = to_clk_periph(hw);

@@ -126,6 +135,7 @@ const struct clk_ops tegra_clk_periph_ops = {
 	.is_enabled = clk_periph_is_enabled,
 	.enable = clk_periph_enable,
 	.disable = clk_periph_disable,
+	.disable_unused = clk_periph_disable_unused,
 	.restore_context = clk_periph_restore_context,
 };

@@ -135,6 +145,7 @@ static const struct clk_ops tegra_clk_periph_nodiv_ops = {
 	.is_enabled = clk_periph_is_enabled,
 	.enable = clk_periph_enable,
 	.disable = clk_periph_disable,
+	.disable_unused = clk_periph_disable_unused,
 	.restore_context = clk_periph_restore_context,
 };

Signature · 1 line

2.29.2

Dmitry Osipenko

author

2020-12-15 21:13 UTC #3 lore raw

PATCH 3/3 clk: tegra: Ensure that PLLU configuration is applied properly

In reply to Dmitry Osipenko

The PLLU (USB) consists of the PLL configuration itself and configuration of the PLLU outputs. The PLLU programming is inconsistent on T30 vs T114, where T114 immediately bails out if PLLU is enabled and T30 re-enables a potentially already enabled PLL (left after bootloader) and then fully reprograms it, which could be unsafe to do. The correct way should be to skip enabling of the PLL if it's already enabled and then apply configuration to the outputs. This patch doesn't fix any known problems, it's a minor improvement.

Signed-off-by Dmitry Osipenko <[email protected]>

---
 drivers/clk/tegra/clk-pll.c | 9 ++++-----
 1 file changed, 4 insertions(+), 5 deletions(-)

drivers/clk/tegra/clk-pll.c +4 -5

index c5cc0a2dac6f..d709ecb7d8d7 100644
@@ -1131,7 +1131,8 @@ static int clk_pllu_enable(struct clk_hw *hw)
 	if (pll->lock)
 		spin_lock_irqsave(pll->lock, flags);
 
-	_clk_pll_enable(hw);
+	if (!clk_pll_is_enabled(hw))
+		_clk_pll_enable(hw);
 
 	ret = clk_pll_wait_for_lock(pll);
 	if (ret < 0)

@@ -1748,15 +1749,13 @@ static int clk_pllu_tegra114_enable(struct clk_hw *hw)
 		return -EINVAL;
 	}
 
-	if (clk_pll_is_enabled(hw))
-		return 0;
-
 	input_rate = clk_hw_get_rate(__clk_get_hw(osc));
 
 	if (pll->lock)
 		spin_lock_irqsave(pll->lock, flags);
 
-	_clk_pll_enable(hw);
+	if (!clk_pll_is_enabled(hw))
+		_clk_pll_enable(hw);
 
 	ret = clk_pll_wait_for_lock(pll);
 	if (ret < 0)

Signature · 1 line

2.29.2