imx8mm: configs: add support for distro boot commands
PATCH v2 1/2 imx8mm: configs: add support for distro boot commands
From: Alice Guo <[email protected]>
Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is deleted because "run distro_bootcmd" is required to be the default boot mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables.
---
Changes for v2:
- remove supported boot device type QSPI
- delete unnecessary environment variables
- set "run distro_bootcmd" to be the default boot mode
configs/imx8mm_evk_defconfig | 2 ++ include/configs/imx8mm_evk.h | 67 +++++++----------------------------- 2 files changed, 14 insertions(+), 55 deletions(-)
configs/imx8mm_evk_defconfig +2 -0
@@ -49,6 +49,8 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y +CONFIG_CMD_PART=y +CONFIG_CMD_FS_GENERIC=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y
include/configs/imx8mm_evk.h +12 -55
81 lines not on this page · raw message
--
2.17.1
PATCH v2 2/2 board: imx8mm: add boot.cmd for distro boot on iMX8MM
From: Alice Guo <[email protected]>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on needs. bootargs is set in this script and root uses the default value " /dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
---
Changes for v2:
- add the additional explanation of boot.cmd in commit message
board/freescale/imx8mm_evk/boot.cmd | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 board/freescale/imx8mm_evk/boot.cmd
board/freescale/imx8mm_evk/boot.cmd new file +35 -0
@@ -0,0 +1,35 @@ +setenv bootargs console=${console} root=${mmcroot}; + +for boot_target in ${boot_targets}; +do + if test "${boot_target}" = "mmc1" ; then + if fatload mmc 1:${mmcpart} ${kernel_addr_r} ${image}; then + if fatload mmc 1:${mmcpart} ${fdt_addr} ${fdt_file}; then + echo Load image and .dtb from SD card(mmc1); + booti ${kernel_addr_r} - ${fdt_addr}; + exit; + fi + fi + fi + + if test "${boot_target}" = "mmc2" ; then + if fatload mmc 2:${mmcpart} ${kernel_addr_r} ${image}; then + if fatload mmc 2:${mmcpart} ${fdt_addr} ${fdt_file}; then + echo Load image and .dtb from eMMC(mmc2); + booti ${kernel_addr_r} - ${fdt_addr}; + exit; + fi + fi + fi + + if test "${boot_target}" = "dhcp" ; then + if dhcp ${kernel_addr_r} ${serverip}:${image}; then + if dhcp ${fdt_addr} ${serverip}:${fdt_file}; then + echo Load image and .dtb from net(dhcp); + booti ${kernel_addr_r} - ${fdt_addr}; + exit; + fi + fi + fi + +done
--
2.17.1
PATCH v2 2/2 board: imx8mm: add boot.cmd for distro boot on iMX8MM
Quoted 74 lines
Subject: [PATCH v2 2/2] board: imx8mm: add boot.cmd for distro boot on iMX8MM
From: Alice Guo <[email protected]>
Distro Boot requires a U-Boot-specific script named boot.scr or boot.scr.uimg which contains boot commands to boot the system. The boot.cmd is such a file. Use mkimage to generate boot.scr or boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimgThe boot.cmd file is an example script and can be modified based on needs. bootargs is set in this script and root uses the default value "
/dev/mmcblk1p2rootwait rw" which can be changed by overriding mmcroot.Signed-off-by Alice Guo <[email protected]>---
Changes for v2:
- add the additional explanation of boot.cmd in commit messageboard/freescale/imx8mm_evk/boot.cmd | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 board/freescale/imx8mm_evk/boot.cmdboard/freescale/imx8mm_evk/boot.cmd new file +6
-0@@ -0,0 +1,35 @@ +setenv bootargs console=${console} root=${mmcroot}; + +for boot_target in ${boot_targets}; +do + if test "${boot_target}" = "mmc1" ; then + if fatload mmc 1:${mmcpart} ${kernel_addr_r} ${image};then
+ if fatload mmc 1:${mmcpart} ${fdt_addr}
${fdt_file}; then
+ echo Load image and .dtb from SD
card(mmc1);
+ booti ${kernel_addr_r} -
${fdt_addr};board/freescale/imx8mm_evk/boot.cmd new file +7
-0+ exit; + fi + fi + fi + + if test "${boot_target}" = "mmc2" ; then + if fatload mmc 2:${mmcpart} ${kernel_addr_r} ${image};then
+ if fatload mmc 2:${mmcpart} ${fdt_addr}
${fdt_file}; then
+ echo Load image and .dtb from
eMMC(mmc2);
+ booti ${kernel_addr_r} -
${fdt_addr};board/freescale/imx8mm_evk/boot.cmd new file +8
-0+ exit; + fi + fi + fi + + if test "${boot_target}" = "dhcp" ; then + if dhcp ${kernel_addr_r} ${serverip}:${image}; then + if dhcp ${fdt_addr} ${serverip}:${fdt_file};then
+ echo Load image and .dtb from
net(dhcp);
+ booti ${kernel_addr_r} -
${fdt_addr};
board/freescale/imx8mm_evk/boot.cmd
Quoted 7 lines
board/freescale/imx8mm_evk/boot.cmd new file +6
-1+ exit; + fi + fi + fi + +done --
PATCH v2 1/2 imx8mm: configs: add support for distro boot commands
In reply to Alice Guo (OSS)Quoted 133 lines
Subject: [PATCH v2 1/2] imx8mm: configs: add support for distro boot commands
From: Alice Guo <[email protected]>
Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PARTis added for command part andCONFIG_CMD_FS_GENERICis for command fstype.
CONFIG_BOOTCOMMANDwhich is defined ininclude/configs/imx8mm_evk.his deleted because "rundistro_bootcmd" is required to be the default boot mode.scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.
kernel_addr_ris the location in RAM where the kernel will be loaded to.Delete unnecessary environment variables.
Signed-off-by Alice Guo <[email protected]>---
Changes for v2:
- remove supported boot device type QSPI
- delete unnecessary environment variables
- set "rundistro_bootcmd" to be the default boot modeconfigs/imx8mm_evk_defconfig | 2 ++ include/configs/imx8mm_evk.h | 67 +++++++----------------------------- 2 files changed, 14 insertions(+), 55 deletions(-)configs/imx8mm_evk_defconfig +2
-0@@ -49,6 +49,8 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y +CONFIG_CMD_PART=y +CONFIG_CMD_FS_GENERIC=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y CONFIG_ENV_OVERWRITE=yinclude/configs/imx8mm_evk.h +12
-55@@ -32,69 +32,26 @@#endif +#ifndef CONFIG_SPL_BUILD +#define BOOT_TARGET_DEVICES (func) \ + func(MMC, mmc, 1) \ + func(MMC, mmc, 2) \ + func(DHCP, dhcp, na) + +#include <config_distro_bootcmd.h> +#endif +/* Initial environment variables */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "script=boot.scr\0" \ + BOOTENV \ + "scriptaddr=0x43500000\0" \ + "kernel_addr_r=0x40880000\0" \ "image=Image\0" \ "console=ttymxc1,115200\0" \ "fdt_addr=0x43000000\0" \ - "boot_fit=no\0" \ "fdt_file=imx8mm-evk.dtb\0" \ - "initrd_addr=0x43800000\0" \ - "bootm_size=0x10000000\0" \ - "mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \ "mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \ "mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \ - "mmcautodetect=yes\0" \ - "mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \ - "loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source\0" \ - "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \ - "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ - "bootm ${loadaddr}; " \ - "else " \ - "if run loadfdt; then " \ - "booti ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi;\0" \ - "netargs=setenv bootargs console=${console} " \ - "root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ - "netboot=echo Booting from net ...; " \ - "run netargs; " \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "${get_cmd} ${loadaddr} ${image}; " \ - "if test ${boot_fit} = yes || test ${boot_fit} = try; then " \ - "bootm ${loadaddr}; " \ - "else " \ - "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "booti ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi;\0" - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loadimage; then " \ - "run mmcboot; " \ - "else run netboot; " \ - "fi; " \ - "fi; " \ - "fi;"
Quoted 3 lines
/* Link Definitions */
#defineCONFIG_LOADADDR0x40480000
--