imx8mm: configs: add support for distro boot commands
PATCH v3 1/2 imx8mm: configs: add support for distro boot commands
From: Alice Guo <[email protected]>
Supported boot device types in iMX8MM: MMC, DHCP.
CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is deleted because "run distro_bootcmd" is required to be the default boot mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to.
Delete unnecessary environment variables.
---
Changes for v3:
- add Reviewed-by
- re-add boot_fit, initrd_addr and bootm_size which may need to be used
Changes for v2:
- remove supported boot device type QSPI
- delete unnecessary environment variables
- set "run distro_bootcmd" to be the default boot mode
configs/imx8mm_evk_defconfig | 2 ++ include/configs/imx8mm_evk.h | 64 +++++++----------------------------- 2 files changed, 14 insertions(+), 52 deletions(-)
configs/imx8mm_evk_defconfig +2 -0
@@ -49,6 +49,8 @@ CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y CONFIG_CMD_FAT=y +CONFIG_CMD_PART=y +CONFIG_CMD_FS_GENERIC=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y CONFIG_ENV_OVERWRITE=y
include/configs/imx8mm_evk.h +12 -52
80 lines not on this page · raw message
--
2.17.1
PATCH v3 2/2 board: imx8mm: add boot.cmd for distro boot on iMX8MM
From: Alice Guo <[email protected]>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg
The boot.cmd file is an example script and can be modified based on needs. bootargs is set in this script and root uses the default value " /dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.
---
Changes for v3:
- add Reviewed-by
Changes for v2:
- add the additional explanation of boot.cmd in commit message
board/freescale/imx8mm_evk/boot.cmd | 35 +++++++++++++++++++++++++++++ 1 file changed, 35 insertions(+) create mode 100644 board/freescale/imx8mm_evk/boot.cmd
board/freescale/imx8mm_evk/boot.cmd new file +35 -0
@@ -0,0 +1,35 @@ +setenv bootargs console=${console} root=${mmcroot}; + +for boot_target in ${boot_targets}; +do + if test "${boot_target}" = "mmc1" ; then + if fatload mmc 1:${mmcpart} ${kernel_addr_r} ${image}; then + if fatload mmc 1:${mmcpart} ${fdt_addr} ${fdt_file}; then + echo Load image and .dtb from SD card(mmc1); + booti ${kernel_addr_r} - ${fdt_addr}; + exit; + fi + fi + fi + + if test "${boot_target}" = "mmc2" ; then + if fatload mmc 2:${mmcpart} ${kernel_addr_r} ${image}; then + if fatload mmc 2:${mmcpart} ${fdt_addr} ${fdt_file}; then + echo Load image and .dtb from eMMC(mmc2); + booti ${kernel_addr_r} - ${fdt_addr}; + exit; + fi + fi + fi + + if test "${boot_target}" = "dhcp" ; then + if dhcp ${kernel_addr_r} ${serverip}:${image}; then + if dhcp ${fdt_addr} ${serverip}:${fdt_file}; then + echo Load image and .dtb from net(dhcp); + booti ${kernel_addr_r} - ${fdt_addr}; + exit; + fi + fi + fi + +done
--
2.17.1
PATCH v3 2/2 board: imx8mm: add boot.cmd for distro boot on iMX8MM
Quoted 11 lines
From: Alice Guo <[email protected]>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value "/dev/mmcblk1p2rootwait rw" which can be changed by overriding mmcroot.Reviewed-by Peng Fan <[email protected]>Signed-off-by Alice Guo <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================
PATCH v3 1/2 imx8mm: configs: add support for distro boot commands
In reply to Alice Guo (OSS)Quoted 11 lines
From: Alice Guo <[email protected]>
Supported boot device types in iMX8MM: MMC, DHCP.CONFIG_CMD_PARTis added for command part andCONFIG_CMD_FS_GENERICis for command fstype.CONFIG_BOOTCOMMANDwhich is defined ininclude/configs/imx8mm_evk.his deleted because "rundistro_bootcmd" is required to be the default boot mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.kernel_addr_ris the location in RAM where the kernel will be loaded to. Delete unnecessary environment variables.
Quoted 2 lines
Reviewed-by Peng Fan <[email protected]>Signed-off-by Alice Guo <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de =====================================================================