Skip to contentSkip to conversation

imx8mm: configs: add support for distro boot commands

PATCH New Alice Guo (OSS) 2 participants 4 messages Dec 18, 2020 – Jan 23, 2021 Arm i.MX and Layerscape

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/2 imx8mm: configs: add support for distro boot commands

From: Alice Guo <[email protected]>

Supported boot device types in iMX8MM: MMC, DHCP.

CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is for command fstype.

CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is deleted because "run distro_bootcmd" is required to be the default boot mode.

scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.

kernel_addr_r is the location in RAM where the kernel will be loaded to.

Delete unnecessary environment variables.

---

Changes for v3:
- add Reviewed-by
- re-add boot_fit, initrd_addr and bootm_size which may need to be used
Changes for v2:
- remove supported boot device type QSPI
- delete unnecessary environment variables
- set "run distro_bootcmd" to be the default boot mode

 configs/imx8mm_evk_defconfig |  2 ++
 include/configs/imx8mm_evk.h | 64 +++++++-----------------------------
 2 files changed, 14 insertions(+), 52 deletions(-)
configs/imx8mm_evk_defconfig +2 -0
index 91d3bc3ac9..4c0dd27e71 100644
@@ -49,6 +49,8 @@ CONFIG_CMD_EXT2=y
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_EXT4_WRITE=y
 CONFIG_CMD_FAT=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_FS_GENERIC=y
 CONFIG_OF_CONTROL=y
 CONFIG_SPL_OF_CONTROL=y
 CONFIG_ENV_OVERWRITE=y
include/configs/imx8mm_evk.h +12 -52

80 lines not on this page · raw message

--
2.17.1

#1 lore raw

PATCH v3 2/2 board: imx8mm: add boot.cmd for distro boot on iMX8MM

From: Alice Guo <[email protected]>

Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg

The boot.cmd file is an example script and can be modified based on needs. bootargs is set in this script and root uses the default value " /dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

---

Changes for v3:
- add Reviewed-by
Changes for v2:
- add the additional explanation of boot.cmd in commit message

 board/freescale/imx8mm_evk/boot.cmd | 35 +++++++++++++++++++++++++++++
 1 file changed, 35 insertions(+)
 create mode 100644 board/freescale/imx8mm_evk/boot.cmd
board/freescale/imx8mm_evk/boot.cmd new file +35 -0
new file mode 100644
index 0000000000..fdfceec263
@@ -0,0 +1,35 @@
+setenv bootargs console=${console} root=${mmcroot};
+
+for boot_target in ${boot_targets};
+do
+        if test "${boot_target}" = "mmc1" ; then
+                if fatload mmc 1:${mmcpart} ${kernel_addr_r} ${image}; then
+                        if fatload mmc 1:${mmcpart} ${fdt_addr} ${fdt_file}; then
+                                echo Load image and .dtb from SD card(mmc1);
+                                booti ${kernel_addr_r} - ${fdt_addr};
+                                exit;
+                        fi
+                fi
+        fi
+
+        if test "${boot_target}" = "mmc2" ; then
+                if fatload mmc 2:${mmcpart} ${kernel_addr_r} ${image}; then
+                        if fatload mmc 2:${mmcpart} ${fdt_addr} ${fdt_file}; then
+                                echo Load image and .dtb from eMMC(mmc2);
+                                booti ${kernel_addr_r} - ${fdt_addr};
+                                exit;
+                        fi
+                fi
+        fi
+
+        if test "${boot_target}" = "dhcp" ; then
+                if dhcp ${kernel_addr_r} ${serverip}:${image}; then
+                        if dhcp ${fdt_addr} ${serverip}:${fdt_file}; then
+                                echo Load image and .dtb from net(dhcp);
+                                booti ${kernel_addr_r} - ${fdt_addr};
+                                exit;
+                        fi
+                fi
+        fi
+
+done

--
2.17.1

#2 lore raw

PATCH v3 2/2 board: imx8mm: add boot.cmd for distro boot on iMX8MM

Quoted 11 lines

From: Alice Guo <[email protected]>
Distro Boot requires a U-Boot-specific script named boot.scr or
boot.scr.uimg which contains boot commands to boot the system. The
boot.cmd is such a file. Use mkimage to generate boot.scr or
boot.scr.uimg from boot.cmd, and the command is:
mkimage -A arm -O linux -T script -C none -a 0 -e 0 -n "Distro Boot Script" -d boot.cmd boot.scr.uimg The boot.cmd file is an example script and can be modified based on
needs. bootargs is set in this script and root uses the default value " /dev/mmcblk1p2 rootwait rw" which can be changed by overriding mmcroot.

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
#3 lore raw

PATCH v3 1/2 imx8mm: configs: add support for distro boot commands

In reply to Alice Guo (OSS)
Quoted 11 lines

From: Alice Guo <[email protected]>
Supported boot device types in iMX8MM: MMC, DHCP. CONFIG_CMD_PART is added for command part and CONFIG_CMD_FS_GENERIC is for command fstype.
CONFIG_BOOTCOMMAND which is defined in include/configs/imx8mm_evk.h is deleted because "run distro_bootcmd" is required to be the default boot mode.
scriptaddr is the location in RAM where boot.scr.uimg/boot.scr will be loaded to prior to execution.
kernel_addr_r is the location in RAM where the kernel will be loaded to. Delete unnecessary environment variables.

Quoted 2 lines

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================