Skip to contentSkip to conversation

Offload software learnt bridge addresses to DSA

PATCH Applied Vladimir Oltean 3 participants 11 messages Jan 6, 2021 – Jan 7, 2021

Subsystems (5)
lore
Share & tools
lore

Vladimir Oltean

author maintainer
#0 lore raw

v4 cover Offload software learnt bridge addresses to DSA

From: Vladimir Oltean <[email protected]>

This series tries to make DSA behave a bit more sanely when bridged with "foreign" (non-DSA) interfaces and source address learning is not supported on the hardware CPU port (which would make things work more seamlessly without software intervention). When a station A connected to a DSA switch port needs to talk to another station B connected to a non-DSA port through the Linux bridge, DSA must explicitly add a route for station B towards its CPU port.

Initial RFC was posted here:
https://patchwork.ozlabs.org/project/netdev/cover/[email protected]/

v2 was posted here:
https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/

v3 was posted here:
https://patchwork.kernel.org/project/netdevbpf/cover/[email protected]/

This is a resend of the previous v3 with some added Reviewed-by tags.

Vladimir Oltean (7):
net: bridge: notify switchdev of disappearance of old FDB entry upon
migration
net: dsa: be louder when a non-legacy FDB operation fails
net: dsa: don't use switchdev_notifier_fdb_info in
dsa_switchdev_event_work
net: dsa: move switchdev event implementation under the same
switch/case statement
net: dsa: exit early in dsa_slave_switchdev_event if we can't program
the FDB
net: dsa: listen for SWITCHDEV_{FDB,DEL}_ADD_TO_DEVICE on foreign
bridge neighbors
net: dsa: ocelot: request DSA to fix up lack of address learning on
CPU port

 drivers/net/dsa/ocelot/felix.c |   1 +
 include/net/dsa.h              |   5 +
 net/bridge/br_fdb.c            |   1 +
 net/dsa/dsa_priv.h             |  12 +++
 net/dsa/slave.c                | 174 +++++++++++++++++++++------------
 5 files changed, 130 insertions(+), 63 deletions(-)
Signature · 1 line
2.25.1
author maintainer
#1 lore raw

PATCH v4 1/7 net: bridge: notify switchdev of disappearance of old FDB entry upon migration

From: Vladimir Oltean <[email protected]>

Currently the bridge emits atomic switchdev notifications for dynamically learnt FDB entries. Monitoring these notifications works wonders for switchdev drivers that want to keep their hardware FDB in sync with the bridge's FDB.

For example station A wants to talk to station B in the diagram below, and we are concerned with the behavior of the bridge on the DUT device:

DUT

 +-------------------------------------+
 |                 br0                 |
 | +------+ +------+ +------+ +------+ |
 | |      | |      | |      | |      | |
 | | swp0 | | swp1 | | swp2 | | eth0 | |
 +-------------------------------------+
      |        |                  |
  Station A    |                  |
               |                  |
         +--+------+--+    +--+------+--+
         |  |      |  |    |  |      |  |
         |  | swp0 |  |    |  | swp0 |  |
 Another |  +------+  |    |  +------+  | Another
  switch |     br0    |    |     br0    | switch
         |  +------+  |    |  +------+  |
         |  |      |  |    |  |      |  |
         |  | swp1 |  |    |  | swp1 |  |
         +--+------+--+    +--+------+--+
                                  |

Station B

Interfaces swp0, swp1, swp2 are handled by a switchdev driver that has the following property: frames injected from its control interface bypass the internal address analyzer logic, and therefore, this hardware does not learn from the source address of packets transmitted by the network stack through it. So, since bridging between eth0 (where Station B is attached) and swp0 (where Station A is attached) is done in software, the switchdev hardware will never learn the source address of Station B. So the traffic towards that destination will be treated as unknown, i.e. flooded.

This is where the bridge notifications come in handy. When br0 on the DUT sees frames with Station B's MAC address on eth0, the switchdev driver gets these notifications and can install a rule to send frames towards Station B's address that are incoming from swp0, swp1, swp2, only towards the control interface. This is all switchdev driver private business, which the notification makes possible.

All is fine until someone unplugs Station B's cable and moves it to the other switch:

DUT

 +-------------------------------------+
 |                 br0                 |
 | +------+ +------+ +------+ +------+ |
 | |      | |      | |      | |      | |
 | | swp0 | | swp1 | | swp2 | | eth0 | |
 +-------------------------------------+
      |        |                  |
  Station A    |                  |
               |                  |
         +--+------+--+    +--+------+--+
         |  |      |  |    |  |      |  |
         |  | swp0 |  |    |  | swp0 |  |
 Another |  +------+  |    |  +------+  | Another
  switch |     br0    |    |     br0    | switch
         |  +------+  |    |  +------+  |
         |  |      |  |    |  |      |  |
         |  | swp1 |  |    |  | swp1 |  |
         +--+------+--+    +--+------+--+
               |

Station B

Luckily for the use cases we care about, Station B is noisy enough that the DUT hears it (on swp1 this time). swp1 receives the frames and delivers them to the bridge, who enters the unlikely path in br_fdb_update of updating an existing entry. It moves the entry in the software bridge to swp1 and emits an addition notification towards that.

As far as the switchdev driver is concerned, all that it needs to ensure is that traffic between Station A and Station B is not forever broken. If it does nothing, then the stale rule to send frames for Station B towards the control interface remains in place. But Station B is no longer reachable via the control interface, but via a port that can offload the bridge port learning attribute. It's just that the port is prevented from learning this address, since the rule overrides FDB updates. So the rule needs to go. The question is via what mechanism.

It sure would be possible for this switchdev driver to keep track of all addresses which are sent to the control interface, and then also listen for bridge notifier events on its own ports, searching for the ones that have a MAC address which was previously sent to the control interface. But this is cumbersome and inefficient. Instead, with one small change, the bridge could notify of the address deletion from the old port, in a symmetrical manner with how it did for the insertion. Then the switchdev driver would not be required to monitor learn/forget events for its own ports. It could just delete the rule towards the control interface upon bridge entry migration. This would make hardware address learning be possible again. Then it would take a few more packets until the hardware and software FDB would be in sync again.

---
Changes in v4:
None.

Changes in v3:
None.

Changes in v2:
Patch is new.

 net/bridge/br_fdb.c | 1 +
 1 file changed, 1 insertion(+)
net/bridge/br_fdb.c +1 -0
index 32ac8343b0ba..b7490237f3fc 100644
@@ -602,6 +602,7 @@ void br_fdb_update(struct net_bridge *br, struct net_bridge_port *source,
 			/* fastpath: update of existing entry */
 			if (unlikely(source != fdb->dst &&
 				     !test_bit(BR_FDB_STICKY, &fdb->flags))) {
+				br_switchdev_fdb_notify(fdb, RTM_DELNEIGH);
 				fdb->dst = source;
 				fdb_modified = true;
 				/* Take over HW learned entry */
Signature · 1 line
2.25.1
Reviewed-by on v4 1/7
#2 lore raw

Re: [PATCH v4 net-next 1/7] net: bridge: notify switchdev of disappearance of old FDB entry upon migration

Quoted 102 lines · Vladimir Oltean

From: Vladimir Oltean <[email protected]>

Currently the bridge emits atomic switchdev notifications for dynamically learnt FDB entries. Monitoring these notifications works wonders for switchdev drivers that want to keep their hardware FDB in sync with the bridge's FDB.

For example station A wants to talk to station B in the diagram below, and we are concerned with the behavior of the bridge on the DUT device:

DUT

 +-------------------------------------+
 |                 br0                 |
 | +------+ +------+ +------+ +------+ |
 | |      | |      | |      | |      | |
 | | swp0 | | swp1 | | swp2 | | eth0 | |
 +-------------------------------------+
      |        |                  |
  Station A    |                  |
               |                  |
         +--+------+--+    +--+------+--+
         |  |      |  |    |  |      |  |
         |  | swp0 |  |    |  | swp0 |  |
 Another |  +------+  |    |  +------+  | Another
  switch |     br0    |    |     br0    | switch
         |  +------+  |    |  +------+  |
         |  |      |  |    |  |      |  |
         |  | swp1 |  |    |  | swp1 |  |
         +--+------+--+    +--+------+--+
                                  |

Station B

Interfaces swp0, swp1, swp2 are handled by a switchdev driver that has the following property: frames injected from its control interface bypass the internal address analyzer logic, and therefore, this hardware does not learn from the source address of packets transmitted by the network stack through it. So, since bridging between eth0 (where Station B is attached) and swp0 (where Station A is attached) is done in software, the switchdev hardware will never learn the source address of Station B. So the traffic towards that destination will be treated as unknown, i.e. flooded.

This is where the bridge notifications come in handy. When br0 on the DUT sees frames with Station B's MAC address on eth0, the switchdev driver gets these notifications and can install a rule to send frames towards Station B's address that are incoming from swp0, swp1, swp2, only towards the control interface. This is all switchdev driver private business, which the notification makes possible.

All is fine until someone unplugs Station B's cable and moves it to the other switch:

DUT

 +-------------------------------------+
 |                 br0                 |
 | +------+ +------+ +------+ +------+ |
 | |      | |      | |      | |      | |
 | | swp0 | | swp1 | | swp2 | | eth0 | |
 +-------------------------------------+
      |        |                  |
  Station A    |                  |
               |                  |
         +--+------+--+    +--+------+--+
         |  |      |  |    |  |      |  |
         |  | swp0 |  |    |  | swp0 |  |
 Another |  +------+  |    |  +------+  | Another
  switch |     br0    |    |     br0    | switch
         |  +------+  |    |  +------+  |
         |  |      |  |    |  |      |  |
         |  | swp1 |  |    |  | swp1 |  |
         +--+------+--+    +--+------+--+
               |

Station B

Luckily for the use cases we care about, Station B is noisy enough that the DUT hears it (on swp1 this time). swp1 receives the frames and delivers them to the bridge, who enters the unlikely path in br_fdb_update of updating an existing entry. It moves the entry in the software bridge to swp1 and emits an addition notification towards that.

As far as the switchdev driver is concerned, all that it needs to ensure is that traffic between Station A and Station B is not forever broken. If it does nothing, then the stale rule to send frames for Station B towards the control interface remains in place. But Station B is no longer reachable via the control interface, but via a port that can offload the bridge port learning attribute. It's just that the port is prevented from learning this address, since the rule overrides FDB updates. So the rule needs to go. The question is via what mechanism.

It sure would be possible for this switchdev driver to keep track of all addresses which are sent to the control interface, and then also listen for bridge notifier events on its own ports, searching for the ones that have a MAC address which was previously sent to the control interface. But this is cumbersome and inefficient. Instead, with one small change, the bridge could notify of the address deletion from the old port, in a symmetrical manner with how it did for the insertion. Then the switchdev driver would not be required to monitor learn/forget events for its own ports. It could just delete the rule towards the control interface upon bridge entry migration. This would make hardware address learning be possible again. Then it would take a few more packets until the hardware and software FDB would be in sync again.

Quoted 4 lines
Signature · 1 line
Florian
author maintainer
#3 lore raw

PATCH v4 2/7 net: dsa: be louder when a non-legacy FDB operation fails

In reply to Vladimir Oltean

From: Vladimir Oltean <[email protected]>

The dev_close() call was added in commit c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification") "to indicate inconsistent situation" when we could not delete an FDB entry from the port.

bridge fdb del d8:58:d7:00:ca:6d dev swp0 self master

It is a bit drastic and at the same time not helpful if the above fails to only print with netdev_dbg log level, but on the other hand to bring the interface down.

So increase the verbosity of the error message, and drop dev_close().

---
Changes in v4:
None.

Changes in v3:
Patch is new.

 net/dsa/slave.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
net/dsa/slave.c +7 -3
index 4a0498bf6c65..d5d389300124 100644
@@ -2072,7 +2072,9 @@ static void dsa_slave_switchdev_event_work(struct work_struct *work)
 
 		err = dsa_port_fdb_add(dp, fdb_info->addr, fdb_info->vid);
 		if (err) {
-			netdev_dbg(dev, "fdb add failed err=%d\n", err);
+			netdev_err(dev,
+				   "failed to add %pM vid %d to fdb: %d\n",
+				   fdb_info->addr, fdb_info->vid, err);
 			break;
 		}
 		fdb_info->offloaded = true;
@@ -2087,9 +2089,11 @@ static void dsa_slave_switchdev_event_work(struct work_struct *work)
 
 		err = dsa_port_fdb_del(dp, fdb_info->addr, fdb_info->vid);
 		if (err) {
-			netdev_dbg(dev, "fdb del failed err=%d\n", err);
-			dev_close(dev);
+			netdev_err(dev,
+				   "failed to delete %pM vid %d from fdb: %d\n",
+				   fdb_info->addr, fdb_info->vid, err);
 		}
+
 		break;
 	}
 	rtnl_unlock();
Signature · 1 line
2.25.1
Reviewed-by on v4 2/7
#4 lore raw

Re: [PATCH v4 net-next 2/7] net: dsa: be louder when a non-legacy FDB operation fails

Quoted 8 lines · Vladimir Oltean

From: Vladimir Oltean <[email protected]>

The dev_close() call was added in commit c9eb3e0f8701 ("net: dsa: Add support for learning FDB through notification") "to indicate inconsistent situation" when we could not delete an FDB entry from the port.

bridge fdb del d8:58:d7:00:ca:6d dev swp0 self master

Quoted 8 lines

It is a bit drastic and at the same time not helpful if the above fails to only print with netdev_dbg log level, but on the other hand to bring the interface down.

So increase the verbosity of the error message, and drop dev_close().

Signature · 1 line
Florian
author maintainer
#5 lore raw

PATCH v4 3/7 net: dsa: don't use switchdev_notifier_fdb_info in dsa_switchdev_event_work

In reply to Vladimir Oltean

From: Vladimir Oltean <[email protected]>

Currently DSA doesn't add FDB entries on the CPU port, because it only does so through switchdev, which is associated with a net_device, and there are none of those for the CPU port.

But actually FDB addresses on the CPU port have some use cases of their own, if the switchdev operations are initiated from within the DSA layer. There is just one problem with the existing code: it passes a structure in dsa_switchdev_event_work which was retrieved directly from switchdev, so it contains a net_device. We need to generalize the contents to something that covers the CPU port as well: the "ds, port" tuple is fine for that.

Note that the new procedure for notifying the successful FDB offload is inspired from the rocker model.

Also, nothing was being done if added_by_user was false. Let's check for that a lot earlier, and don't actually bother to schedule the worker for nothing.

---
Changes in v4:
None.

Changes in v3:
None.

Changes in v2:
Small cosmetic changes (reverse Christmas notation)

 net/dsa/dsa_priv.h |  12 +++++
 net/dsa/slave.c    | 106 ++++++++++++++++++++++-----------------------
 2 files changed, 65 insertions(+), 53 deletions(-)
net/dsa/dsa_priv.h +12 -0
index 7c96aae9062c..c04225f74929 100644
@@ -73,6 +73,18 @@ struct dsa_notifier_mtu_info {
 	int mtu;
 };
 
+struct dsa_switchdev_event_work {
+	struct dsa_switch *ds;
+	int port;
+	struct work_struct work;
+	unsigned long event;
+	/* Specific for SWITCHDEV_FDB_ADD_TO_DEVICE and
+	 * SWITCHDEV_FDB_DEL_TO_DEVICE
+	 */
+	unsigned char addr[ETH_ALEN];
+	u16 vid;
+};
+
 struct dsa_slave_priv {
 	/* Copy of CPU port xmit for faster access in slave transmit hot path */
 	struct sk_buff *	(*xmit)(struct sk_buff *skb,
net/dsa/slave.c +53 -53

166 lines not on this page · raw message

Signature · 1 line
2.25.1
author maintainer
#6 lore raw

PATCH v4 4/7 net: dsa: move switchdev event implementation under the same switch/case statement

In reply to Vladimir Oltean

From: Vladimir Oltean <[email protected]>

We'll need to start listening to SWITCHDEV_FDB_{ADD,DEL}_TO_DEVICE events even for interfaces where dsa_slave_dev_check returns false, so we need that check inside the switch-case statement for SWITCHDEV_FDB_*.

This movement also avoids a useless allocation / free of switchdev_work on the untreated "default event" case.

---
Changes in v4:
None.

Changes in v3:
None.

Changes in v2:
None.

 net/dsa/slave.c | 35 ++++++++++++++++-------------------
 1 file changed, 16 insertions(+), 19 deletions(-)
net/dsa/slave.c +16 -19
index 5e4fb44c2820..42ec18a4c7ba 100644
@@ -2119,31 +2119,29 @@ static int dsa_slave_switchdev_event(struct notifier_block *unused,
 	struct dsa_port *dp;
 	int err;
 
-	if (event == SWITCHDEV_PORT_ATTR_SET) {
+	switch (event) {
+	case SWITCHDEV_PORT_ATTR_SET:
 		err = switchdev_handle_port_attr_set(dev, ptr,
 						     dsa_slave_dev_check,
 						     dsa_slave_port_attr_set);
 		return notifier_from_errno(err);
-	}
-
-	if (!dsa_slave_dev_check(dev))
-		return NOTIFY_DONE;
+	case SWITCHDEV_FDB_ADD_TO_DEVICE:
+	case SWITCHDEV_FDB_DEL_TO_DEVICE:
+		if (!dsa_slave_dev_check(dev))
+			return NOTIFY_DONE;
 
-	dp = dsa_slave_to_port(dev);
+		dp = dsa_slave_to_port(dev);
 
-	switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC);
-	if (!switchdev_work)
-		return NOTIFY_BAD;
+		switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC);
+		if (!switchdev_work)
+			return NOTIFY_BAD;
 
-	INIT_WORK(&switchdev_work->work,
-		  dsa_slave_switchdev_event_work);
-	switchdev_work->ds = dp->ds;
-	switchdev_work->port = dp->index;
-	switchdev_work->event = event;
+		INIT_WORK(&switchdev_work->work,
+			  dsa_slave_switchdev_event_work);
+		switchdev_work->ds = dp->ds;
+		switchdev_work->port = dp->index;
+		switchdev_work->event = event;
 
-	switch (event) {
-	case SWITCHDEV_FDB_ADD_TO_DEVICE:
-	case SWITCHDEV_FDB_DEL_TO_DEVICE:
 		fdb_info = ptr;
 
 		if (!fdb_info->added_by_user) {
@@ -2156,13 +2154,12 @@ static int dsa_slave_switchdev_event(struct notifier_block *unused,
 		switchdev_work->vid = fdb_info->vid;
 
 		dev_hold(dev);
+		dsa_schedule_work(&switchdev_work->work);
 		break;
 	default:
-		kfree(switchdev_work);
 		return NOTIFY_DONE;
 	}
 
-	dsa_schedule_work(&switchdev_work->work);
 	return NOTIFY_OK;
 }
 
Signature · 1 line
2.25.1
author maintainer
#7 lore raw

PATCH v4 5/7 net: dsa: exit early in dsa_slave_switchdev_event if we can't program the FDB

In reply to Vladimir Oltean

From: Vladimir Oltean <[email protected]>

Right now, the following would happen for a switch driver that does not implement .port_fdb_add or .port_fdb_del.

dsa_slave_switchdev_event returns NOTIFY_OK and schedules:
-> dsa_slave_switchdev_event_work
-> dsa_port_fdb_add

      -> dsa_port_notify(DSA_NOTIFIER_FDB_ADD)
         -> dsa_switch_fdb_add
            -> if (!ds->ops->port_fdb_add) return -EOPNOTSUPP;

-> an error is printed with dev_dbg, and
dsa_fdb_offload_notify(switchdev_work) is not called.

We can avoid scheduling the worker for nothing and say NOTIFY_DONE. Because we don't call dsa_fdb_offload_notify, the static FDB entry will remain just in the software bridge.

---
Changes in v4:
None.

Changes in v3:
s/NOTIFY_OK/NOTIFY_DONE/ in commit description.

Changes in v2:
Patch is new.

 net/dsa/slave.c | 3 +++
 1 file changed, 3 insertions(+)
net/dsa/slave.c +3 -0
index 42ec18a4c7ba..37dffe5bc46f 100644
@@ -2132,6 +2132,9 @@ static int dsa_slave_switchdev_event(struct notifier_block *unused,
 
 		dp = dsa_slave_to_port(dev);
 
+		if (!dp->ds->ops->port_fdb_add || !dp->ds->ops->port_fdb_del)
+			return NOTIFY_DONE;
+
 		switchdev_work = kzalloc(sizeof(*switchdev_work), GFP_ATOMIC);
 		if (!switchdev_work)
 			return NOTIFY_BAD;
Signature · 1 line
2.25.1
author maintainer
#8 lore raw

PATCH v4 6/7 net: dsa: listen for SWITCHDEV_{FDB,DEL}_ADD_TO_DEVICE on foreign bridge neighbors

In reply to Vladimir Oltean

From: Vladimir Oltean <[email protected]>

Some DSA switches (and not only) cannot learn source MAC addresses from packets injected from the CPU. They only perform hardware address learning from inbound traffic.

This can be problematic when we have a bridge spanning some DSA switch ports and some non-DSA ports (which we'll call "foreign interfaces" from DSA's perspective).

There are 2 classes of problems created by the lack of learning on CPU-injected traffic:
- excessive flooding, due to the fact that DSA treats those addresses as unknown
- the risk of stale routes, which can lead to temporary packet loss

To illustrate the second class, consider the following situation, which is common in production equipment (wireless access points, where there is a WLAN interface and an Ethernet switch, and these form a single bridging domain).

AP 1:

 +------------------------------------------------------------------------+
 |                                          br0                           |
 +------------------------------------------------------------------------+
 +------------+ +------------+ +------------+ +------------+ +------------+
 |    swp0    | |    swp1    | |    swp2    | |    swp3    | |    wlan0   |
 +------------+ +------------+ +------------+ +------------+ +------------+
       |                                                       ^        ^
       |                                                       |        |
       |                                                       |        |
       |                                                    Client A  Client B
       |
       |
       |
 +------------+ +------------+ +------------+ +------------+ +------------+
 |    swp0    | |    swp1    | |    swp2    | |    swp3    | |    wlan0   |
 +------------+ +------------+ +------------+ +------------+ +------------+
 +------------------------------------------------------------------------+
 |                                          br0                           |
 +------------------------------------------------------------------------+

AP 2

- br0 of AP 1 will know that Clients A and B are reachable via wlan0
- the hardware fdb of a DSA switch driver today is not kept in sync with the software entries on other bridge ports, so it will not know that clients A and B are reachable via the CPU port UNLESS the hardware switch itself performs SA learning from traffic injected from the CPU. Nonetheless, a substantial number of switches don't.
- the hardware fdb of the DSA switch on AP 2 may autonomously learn that Client A and B are reachable through swp0. Therefore, the software br0 of AP 2 also may or may not learn this. In the example we're illustrating, some Ethernet traffic has been going on, and br0 from AP 2 has indeed learnt that it can reach Client B through swp0.

One of the wireless clients, say Client B, disconnects from AP 1 and roams to AP 2. The topology now looks like this:

AP 1:

 +------------------------------------------------------------------------+
 |                                          br0                           |
 +------------------------------------------------------------------------+
 +------------+ +------------+ +------------+ +------------+ +------------+
 |    swp0    | |    swp1    | |    swp2    | |    swp3    | |    wlan0   |
 +------------+ +------------+ +------------+ +------------+ +------------+
       |                                                            ^
       |                                                            |
       |                                                         Client A
       |
       |
       |                                                         Client B
       |                                                            |
       |                                                            v
 +------------+ +------------+ +------------+ +------------+ +------------+
 |    swp0    | |    swp1    | |    swp2    | |    swp3    | |    wlan0   |
 +------------+ +------------+ +------------+ +------------+ +------------+
 +------------------------------------------------------------------------+
 |                                          br0                           |
 +------------------------------------------------------------------------+

AP 2

- br0 of AP 1 still knows that Client A is reachable via wlan0 (no change)
- br0 of AP 1 will (possibly) know that Client B has left wlan0. There are cases where it might never find out though. Either way, DSA today does not process that notification in any way.
- the hardware FDB of the DSA switch on AP 1 may learn autonomously that Client B can be reached via swp0, if it receives any packet with Client 1's source MAC address over Ethernet.
- the hardware FDB of the DSA switch on AP 2 still thinks that Client B can be reached via swp0. It does not know that it has roamed to wlan0, because it doesn't perform SA learning from the CPU port.

Now Client A contacts Client B.
AP 1 routes the packet fine towards swp0 and delivers it on the Ethernet segment.
AP 2 sees a frame on swp0 and its fdb says that the destination is swp0. Hairpinning is disabled => drop.

This problem comes from the fact that these switches have a 'blind spot' for addresses coming from software bridging. The generic solution is not to assume that hardware learning can be enabled somehow, but to listen to more bridge learning events. It turns out that the bridge driver does learn in software from all inbound frames, in __br_handle_local_finish. A proper SWITCHDEV_FDB_ADD_TO_DEVICE notification is emitted for the addresses serviced by the bridge on 'foreign' interfaces. The software bridge also does the right thing on migration, by notifying that the old entry is deleted, so that does not need to be special-cased in DSA. When it is deleted, we just need to delete our static FDB entry towards the CPU too, and wait.

The problem is that DSA currently only cares about SWITCHDEV_FDB_ADD_TO_DEVICE events received on its own interfaces, such as static FDB entries.

Luckily we can change that, and DSA can listen to all switchdev FDB add/del events in the system and figure out if those events were emitted by a bridge that spans at least one of DSA's own ports. In case that is true, DSA will also offload that address towards its own CPU port, in the eventuality that there might be bridge clients attached to the DSA switch who want to talk to the station connected to the foreign interface.

In terms of implementation, we need to keep the fdb_info->added_by_user check for the case where the switchdev event was targeted directly at a DSA switch port. But we don't need to look at that flag for snooped events. So the check is currently too late, we need to move it earlier. This also simplifies the code a bit, since we avoid uselessly allocating and freeing switchdev_work.

We could probably do some improvements in the future. For example, multi-bridge support is rudimentary at the moment. If there are two bridges spanning a DSA switch's ports, and both of them need to service the same MAC address, then what will happen is that the migration of one of those stations will trigger the deletion of the FDB entry from the CPU port while it is still used by other bridge. That could be improved with reference counting but is left for another time.

This behavior needs to be enabled at driver level by setting ds->assisted_learning_on_cpu_port = true. This is because we don't want to inflict a potential performance penalty (accesses through MDIO/I2C/SPI are expensive) to hardware that really doesn't need it because address learning on the CPU port works there.

---
Changes in v4:
None.

Changes in v3:
- s/learning_broken/assisted_learning/
- don't call dev_hold unless it's a DSA slave interface, to avoid broken refcounting

Changes in v2:
Made the behavior conditional.

 include/net/dsa.h |  5 ++++
 net/dsa/slave.c   | 66 +++++++++++++++++++++++++++++++++++++++--------
 2 files changed, 60 insertions(+), 11 deletions(-)
include/net/dsa.h +5 -0
index 4e60d2610f20..6b74690bd8d4 100644
@@ -319,6 +319,11 @@ struct dsa_switch {
 	 */
 	bool			untag_bridge_pvid;
 
+	/* Let DSA manage the FDB entries towards the CPU, based on the
+	 * software bridge database.
+	 */
+	bool			assisted_learning_on_cpu_port;
+
 	/* In case vlan_filtering_is_global is set, the VLAN awareness state
 	 * should be retrieved from here and not from the per-port settings.
 	 */
net/dsa/slave.c +55 -11

89 lines not on this page · raw message

Signature · 1 line
2.25.1
author maintainer
#9 lore raw

PATCH v4 7/7 net: dsa: ocelot: request DSA to fix up lack of address learning on CPU port

In reply to Vladimir Oltean

From: Vladimir Oltean <[email protected]>

Given the following setup:

ip link add br0 type bridge
ip link set eno0 master br0
ip link set swp0 master br0
ip link set swp1 master br0
ip link set swp2 master br0
ip link set swp3 master br0

Currently, packets received on a DSA slave interface (such as swp0) which should be routed by the software bridge towards a non-switch port (such as eno0) are also flooded towards the other switch ports (swp1, swp2, swp3) because the destination is unknown to the hardware switch.

This patch addresses the issue by monitoring the addresses learnt by the software bridge on eno0, and adding/deleting them as static FDB entries on the CPU port accordingly.

---
Changes in v4:
None.

Changes in v3:
s/learning_broken/assisted_learning/

Changes in v2:
Patch is new.

 drivers/net/dsa/ocelot/felix.c | 1 +
 1 file changed, 1 insertion(+)
drivers/net/dsa/ocelot/felix.c +1 -0
index 7dc230677b78..90c3c76f21b2 100644
@@ -629,6 +629,7 @@ static int felix_setup(struct dsa_switch *ds)
 
 	ds->mtu_enforcement_ingress = true;
 	ds->configure_vlan_while_not_filtering = true;
+	ds->assisted_learning_on_cpu_port = true;
 
 	return 0;
 }
Signature · 1 line
2.25.1
#10 lore raw
In reply to Vladimir Oltean
This series was applied to netdev/net-next.git (refs/heads/master):

Hello:

This series was applied to netdev/net-next.git (refs/heads/master):

Quoted 11 lines · On Wed, 6 Jan 2021 11:51:29 +0200 you wrote:

From: Vladimir Oltean <[email protected]>

This series tries to make DSA behave a bit more sanely when bridged with "foreign" (non-DSA) interfaces and source address learning is not supported on the hardware CPU port (which would make things work more seamlessly without software intervention). When a station A connected to a DSA switch port needs to talk to another station B connected to a non-DSA port through the Linux bridge, DSA must explicitly add a route for station B towards its CPU port.

[...]

Here is the summary with links:
- [v4,net-next,1/7] net: bridge: notify switchdev of disappearance of old FDB entry upon migration

    https://git.kernel.org/netdev/net-next/c/90dc8fd36078
  - [v4,net-next,2/7] net: dsa: be louder when a non-legacy FDB operation fails
    https://git.kernel.org/netdev/net-next/c/2fd186501b1c
  - [v4,net-next,3/7] net: dsa: don't use switchdev_notifier_fdb_info in dsa_switchdev_event_work
    https://git.kernel.org/netdev/net-next/c/c4bb76a9a0ef
  - [v4,net-next,4/7] net: dsa: move switchdev event implementation under the same switch/case statement
    https://git.kernel.org/netdev/net-next/c/447d290a58bd
  - [v4,net-next,5/7] net: dsa: exit early in dsa_slave_switchdev_event if we can't program the FDB
    https://git.kernel.org/netdev/net-next/c/5fb4a451a87d
  - [v4,net-next,6/7] net: dsa: listen for SWITCHDEV_{FDB,DEL}_ADD_TO_DEVICE on foreign bridge neighbors
    https://git.kernel.org/netdev/net-next/c/d5f19486cee7
  - [v4,net-next,7/7] net: dsa: ocelot: request DSA to fix up lack of address learning on CPU port
    https://git.kernel.org/netdev/net-next/c/c54913c1d4ee

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html