Remove LPC register partitioning
Subsystems (6)
v5 cover Remove LPC register partitioning
The LPC controller has no concept of the BMC and the Host partitions. The incorrect partitioning can impose unnecessary range restrictions on register access through the syscon regmap interface.
For instance, HICRB contains the I/O port address configuration of KCS channel 1/2. However, the KCS#1/#2 drivers cannot access HICRB as it is located at the other LPC partition.
In addition, to be backward compatible, the newly added HW control bits could be located at any reserved bits over the LPC addressing space.
Thereby, this patch series aims to remove the LPC partitioning for better driver development and maintenance. This requires the change to both the device tree and the driver implementation. To ensure both sides are synchronously updated, a v2 binding check is added.
Chagnes since v4:
- Add child node example in dt-bindings.
Chagnes since v3:
- Revise binding check as suggested by Haiyue Wang.
Changes since v2:
- Add v2 binding check to ensure the synchronization between the device tree change and the driver register offset fix.
Changes since v1:
- Add the fix to the aspeed-lpc binding documentation.
Chia-Wei, Wang (5):
dt-bindings: aspeed-lpc: Remove LPC partitioning
ARM: dts: Remove LPC BMC and Host partitions
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
soc: aspeed: Adapt to new LPC device tree layout
.../devicetree/bindings/mfd/aspeed-lpc.txt | 100 ++++--------- arch/arm/boot/dts/aspeed-g4.dtsi | 74 ++++------ arch/arm/boot/dts/aspeed-g5.dtsi | 135 ++++++++---------- arch/arm/boot/dts/aspeed-g6.dtsi | 135 ++++++++---------- drivers/char/ipmi/kcs_bmc_aspeed.c | 27 ++-- drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 17 ++- drivers/soc/aspeed/aspeed-lpc-ctrl.c | 20 ++- drivers/soc/aspeed/aspeed-lpc-snoop.c | 23 +-- 8 files changed, 229 insertions(+), 302 deletions(-)
Signature · 1 line
2.17.1
PATCH v5 1/5 dt-bindings: aspeed-lpc: Remove LPC partitioning
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
--- .../devicetree/bindings/mfd/aspeed-lpc.txt | 100 +++++------------- 1 file changed, 25 insertions(+), 75 deletions(-)
Documentation/devicetree/bindings/mfd/aspeed-lpc.txt +25 -75
@@ -9,13 +9,7 @@ primary use case of the Aspeed LPC controller is as a slave on the bus conditions it can also take the role of bus master. The LPC controller is represented as a multi-function device to account for the -mix of functionality it provides. The principle split is between the register -layout at the start of the I/O space which is, to quote the Aspeed datasheet, -"basically compatible with the [LPC registers from the] popular BMC controller -H8S/2168[1]", and everything else, where everything else is an eclectic -collection of functions with a esoteric register layout. "Everything else", -here labeled the "host" portion of the controller, includes, but is not limited -to: +mix of functionality, which includes, but is not limited to: * An IPMI Block Transfer[2] Controller
@@ -44,80 +38,36 @@ Required properties =================== - compatible: One of: - "aspeed,ast2400-lpc", "simple-mfd" - "aspeed,ast2500-lpc", "simple-mfd" - "aspeed,ast2600-lpc", "simple-mfd" + "aspeed,ast2400-lpc-v2", "simple-mfd", "syscon" + "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon" + "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon" - reg: contains the physical address and length values of the Aspeed LPC memory region. - #address-cells: <1> - #size-cells: <1> -- ranges: Maps 0 to the physical address and length of the LPC memory - region - -Required LPC Child nodes -======================== - -BMC Node --------- - -- compatible: One of: - "aspeed,ast2400-lpc-bmc" - "aspeed,ast2500-lpc-bmc" - "aspeed,ast2600-lpc-bmc" - -- reg: contains the physical address and length values of the - H8S/2168-compatible LPC controller memory region - -Host Node ---------- - -- compatible: One of: - "aspeed,ast2400-lpc-host", "simple-mfd", "syscon" - "aspeed,ast2500-lpc-host", "simple-mfd", "syscon" - "aspeed,ast2600-lpc-host", "simple-mfd", "syscon" - -- reg: contains the address and length values of the host-related - register space for the Aspeed LPC controller - -- #address-cells: <1> -- #size-cells: <1> -- ranges: Maps 0 to the address and length of the host-related LPC memory +- ranges: Maps 0 to the physical address and length of the LPC memory region Example: lpc: lpc at 1e789000 { - compatible = "aspeed,ast2500-lpc", "simple-mfd"; + compatible = "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon"; reg = <0x1e789000 0x1000>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x1e789000 0x1000>; - lpc_bmc: lpc-bmc at 0 { - compatible = "aspeed,ast2500-lpc-bmc"; + lpc_snoop: lpc-snoop at 0 { + compatible = "aspeed,ast2600-lpc-snoop"; reg = <0x0 0x80>; - }; - - lpc_host: lpc-host at 80 { - compatible = "aspeed,ast2500-lpc-host", "simple-mfd", "syscon"; - reg = <0x80 0x1e0>; - reg-io-width = <4>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x80 0x1e0>; + interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>; + snoop-ports = <0x80>; }; }; -BMC Node Children -================== - - -Host Node Children -================== LPC Host Interface Controller -------------------
@@ -149,14 +99,12 @@ Optional properties: Example: -lpc-host at 80 { - lpc_ctrl: lpc-ctrl at 0 { - compatible = "aspeed,ast2500-lpc-ctrl"; - reg = <0x0 0x80>; - clocks = <&syscon ASPEED_CLK_GATE_LCLK>; - memory-region = <&flash_memory>; - flash = <&spi>; - }; +lpc_ctrl: lpc-ctrl at 80 { + compatible = "aspeed,ast2500-lpc-ctrl"; + reg = <0x80 0x80>; + clocks = <&syscon ASPEED_CLK_GATE_LCLK>; + memory-region = <&flash_memory>; + flash = <&spi>; }; LPC Host Controller
@@ -179,9 +127,9 @@ Required properties: Example: -lhc: lhc at 20 { +lhc: lhc at a0 { compatible = "aspeed,ast2500-lhc"; - reg = <0x20 0x24 0x48 0x8>; + reg = <0xa0 0x24 0xc8 0x8>; }; LPC reset control
@@ -192,16 +140,18 @@ state of the LPC bus. Some systems may chose to modify this configuration. Required properties: - - compatible: "aspeed,ast2600-lpc-reset" or - "aspeed,ast2500-lpc-reset" - "aspeed,ast2400-lpc-reset" + - compatible: One of: + "aspeed,ast2600-lpc-reset"; + "aspeed,ast2500-lpc-reset"; + "aspeed,ast2400-lpc-reset"; + - reg: offset and length of the IP in the LHC memory region - #reset-controller indicates the number of reset cells expected Example: -lpc_reset: reset-controller at 18 { +lpc_reset: reset-controller at 98 { compatible = "aspeed,ast2500-lpc-reset"; - reg = <0x18 0x4>; + reg = <0x98 0x4>; #reset-cells = <1>; };
Signature · 1 line
2.17.1
Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
Quoted 6 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
Signed-off-by Chia-Wei, Wang <[email protected]>
Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
In reply to Chia-Wei, WangQuoted 10 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
Signed-off-by Chia-Wei, Wang <[email protected]>--- .../devicetree/bindings/mfd/aspeed-lpc.txt | 100 +++++------------- 1 file changed, 25 insertions(+), 75 deletions(-)
Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
In reply to Chia-Wei, WangQuoted 6 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
Signed-off-by Chia-Wei, Wang <[email protected]>
Any thoughts Lee? If you ack it would you be happy for the patch to go through the Aspeed tree?
Andrew
RE: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
Hi All,
Do you have update on this patch series?
Aspeed has subsequent LPC module upstream plan.
We hope that the following patches can be on the basis of the fixed LPC layout. Thanks.
Chiawei
Quoted 20 lines
-----Original Message-----
From: Andrew Jeffery <[email protected]>
Sent: Wednesday, January 27, 2021 8:25 AM
To: Lee Jones <[email protected]>
Subject: Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioningQuoted 6 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
Signed-off-by Chia-Wei, Wang <[email protected]>Any thoughts Lee? If you ack it would you be happy for the patch to go through the Aspeed tree?
Andrew
Joel Stanley
maintainerRe: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
Hi Chaiwei,
Quoted 6 lines · ChiaWei Wang
Hi All,
Do you have update on this patch series?
Aspeed has subsequent LPC module upstream plan.
We hope that the following patches can be on the basis of the fixed LPC layout.
Andrew has expressed his support for your changes. I will take time to closely review your proposal this week.
We will set the goal of having this rework merged for the next merge window.
Cheers,
Joel
Quoted 24 lines
Thanks.
Chiawei
Quoted 20 lines
-----Original Message-----
From: Andrew Jeffery <[email protected]>
Sent: Wednesday, January 27, 2021 8:25 AM
To: Lee Jones <[email protected]>
Subject: Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioningQuoted 6 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
Signed-off-by Chia-Wei, Wang <[email protected]>Any thoughts Lee? If you ack it would you be happy for the patch to go through the Aspeed tree?
Andrew
RE: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
Hi Joel,
Thanks for your feedback.
Really appreciate all your review effort.
Chiawei
Quoted 53 lines
-----Original Message-----
From: Joel Stanley <[email protected]>
Sent: Wednesday, February 17, 2021 3:45 PM
To: ChiaWei Wang <[email protected]>
Subject: Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioningHi Chaiwei,
Quoted 6 lines · ChiaWei Wang
Hi All,
Do you have update on this patch series?
Aspeed has subsequent LPC module upstream plan.
We hope that the following patches can be on the basis of the fixed LPClayout.
Andrew has expressed his support for your changes. I will take time to closely review your proposal this week.
We will set the goal of having this rework merged for the next merge window.
Cheers,
Joel
Quoted 25 lines
Thanks.
Chiawei
Quoted 21 lines
-----Original Message-----
From: Andrew Jeffery <[email protected]>
Sent: Wednesday, January 27, 2021 8:25 AM
To: Lee Jones <[email protected]>
Subject: Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioningQuoted 6 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions. This patch fixes the documentation by removing the description on LPC partitions. The register offsets illustrated in the DTS node examples are also fixed to adapt to the LPC DTS change.
Signed-off-by Chia-Wei, Wang <[email protected]>Any thoughts Lee? If you ack it would you be happy for the patch to go through the Aspeed tree?
Andrew
Re: [PATCH v5 1/5] dt-bindings: aspeed-lpc: Remove LPC partitioning
In reply to Joel StanleyQuoted 6 lines · Joel Stanley
Hi Chaiwei,
Quoted 3 lines · ChiaWei Wang
Hi All,
Quoted 9 lines
Quoted 3 lines
Do you have update on this patch series?
Aspeed has subsequent LPC module upstream plan.
We hope that the following patches can be on the basis of the fixed LPC layout.Andrew has expressed his support for your changes. I will take time to closely review your proposal this week.
We will set the goal of having this rework merged for the next merge window.
FWIW I have a patch series that builds on top of Chiawei's changes. Once some weather has passed and some power is restored I should be able to test then send it out.
Andrew
PATCH v5 2/5 ARM: dts: Remove LPC BMC and Host partitions
In reply to Chia-Wei, WangThe LPC controller has no concept of the BMC and the Host partitions.
A concrete instance is that the HICRB[5:4] are for the I/O port address configurtaion of KCS channel 1/2. However, the KCS driver cannot access HICRB for channel 1/2 initialization via syscon regmap interface due to the parition boundary. (i.e. offset 80h)
In addition, for the HW design backward compatibility, a newly added HW control bit could be located at any reserved one over the LPC addressing space. Thereby, this patch removes the lpc-bmc and lpc-host child node and thus the LPC partitioning.
Note that this change requires the synchronization between device tree change and the driver change. To prevent the misuse of old devicetrees with new drivers, or vice versa, the v2 compatible strings are adopted for the LPC device as listed:
"aspeed,ast2400-lpc-v2" "aspeed,ast2500-lpc-v2" "aspeed,ast2600-lpc-v2"
--- arch/arm/boot/dts/aspeed-g4.dtsi | 74 +++++++---------- arch/arm/boot/dts/aspeed-g5.dtsi | 135 ++++++++++++++----------------- arch/arm/boot/dts/aspeed-g6.dtsi | 135 ++++++++++++++----------------- 3 files changed, 148 insertions(+), 196 deletions(-)
arch/arm/boot/dts/aspeed-g4.dtsi +30 -44
@@ -343,58 +343,44 @@ }; lpc: lpc at 1e789000 { - compatible = "aspeed,ast2400-lpc", "simple-mfd"; + compatible = "aspeed,ast2400-lpc-v2", "simple-mfd", "syscon"; reg = <0x1e789000 0x1000>; + reg-io-width = <4>; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x1e789000 0x1000>; - lpc_bmc: lpc-bmc at 0 { - compatible = "aspeed,ast2400-lpc-bmc"; - reg = <0x0 0x80>; + lpc_ctrl: lpc-ctrl at 80 { + compatible = "aspeed,ast2400-lpc-ctrl"; + reg = <0x80 0x10>; + clocks = <&syscon ASPEED_CLK_GATE_LCLK>; + status = "disabled"; }; - lpc_host: lpc-host at 80 { - compatible = "aspeed,ast2400-lpc-host", "simple-mfd", "syscon"; - reg = <0x80 0x1e0>; - reg-io-width = <4>; - - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x80 0x1e0>; - - lpc_ctrl: lpc-ctrl at 0 { - compatible = "aspeed,ast2400-lpc-ctrl"; - reg = <0x0 0x10>; - clocks = <&syscon ASPEED_CLK_GATE_LCLK>; - status = "disabled"; - }; - - lpc_snoop: lpc-snoop at 10 { - compatible = "aspeed,ast2400-lpc-snoop"; - reg = <0x10 0x8>; - interrupts = <8>; - status = "disabled"; - }; - - lhc: lhc at 20 { - compatible = "aspeed,ast2400-lhc"; - reg = <0x20 0x24 0x48 0x8>; - }; - - lpc_reset: reset-controller at 18 { - compatible = "aspeed,ast2400-lpc-reset"; - reg = <0x18 0x4>; - #reset-cells = <1>; - }; - - ibt: ibt at c0 { - compatible = "aspeed,ast2400-ibt-bmc"; - reg = <0xc0 0x18>; - interrupts = <8>; - status = "disabled"; - }; + lpc_snoop: lpc-snoop at 90 { + compatible = "aspeed,ast2400-lpc-snoop"; + reg = <0x90 0x8>; + interrupts = <8>; + status = "disabled"; + }; + + lhc: lhc at a0 { + compatible = "aspeed,ast2400-lhc"; + reg = <0xa0 0x24 0xc8 0x8>; + }; + + lpc_reset: reset-controller at 98 { + compatible = "aspeed,ast2400-lpc-reset"; + reg = <0x98 0x4>; + #reset-cells = <1>; + }; + + ibt: ibt at 140 { + compatible = "aspeed,ast2400-ibt-bmc"; + reg = <0x140 0x18>; + interrupts = <8>; + status = "disabled"; }; };
arch/arm/boot/dts/aspeed-g5.dtsi +59 -76
149 lines not on this page · raw message
arch/arm/boot/dts/aspeed-g6.dtsi +59 -76
149 lines not on this page · raw message
Signature · 1 line
2.17.1
Re: [PATCH v5 2/5] ARM: dts: Remove LPC BMC and Host partitions
Quoted 17 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions.
A concrete instance is that the HICRB[5:4] are for the I/O port address configurtaion of KCS channel 1/2. However, the KCS driver cannot access HICRB for channel 1/2 initialization via syscon regmap interface due to the parition boundary. (i.e. offset 80h)
In addition, for the HW design backward compatibility, a newly added HW control bit could be located at any reserved one over the LPC addressing space. Thereby, this patch removes the lpc-bmc and lpc-host child node and thus the LPC partitioning.
Note that this change requires the synchronization between device tree change and the driver change. To prevent the misuse of old devicetrees with new drivers, or vice versa, the v2 compatible strings are adopted for the LPC device as listed:
Quoted 5 lines
"aspeed,ast2400-lpc-v2" "aspeed,ast2500-lpc-v2" "aspeed,ast2600-lpc-v2"Signed-off-by Chia-Wei, Wang <[email protected]>
Re: [PATCH v5 2/5] ARM: dts: Remove LPC BMC and Host partitions
In reply to Chia-Wei, WangQuoted 21 lines · Wang
The LPC controller has no concept of the BMC and the Host partitions.
A concrete instance is that the HICRB[5:4] are for the I/O port address configurtaion of KCS channel 1/2. However, the KCS driver cannot access HICRB for channel 1/2 initialization via syscon regmap interface due to the parition boundary. (i.e. offset 80h)
In addition, for the HW design backward compatibility, a newly added HW control bit could be located at any reserved one over the LPC addressing space. Thereby, this patch removes the lpc-bmc and lpc-host child node and thus the LPC partitioning.
Note that this change requires the synchronization between device tree change and the driver change. To prevent the misuse of old devicetrees with new drivers, or vice versa, the v2 compatible strings are adopted for the LPC device as listed:
"aspeed,ast2400-lpc-v2" "aspeed,ast2500-lpc-v2" "aspeed,ast2600-lpc-v2"
Quoted 5 lines
Signed-off-by Chia-Wei, Wang <[email protected]>--- arch/arm/boot/dts/aspeed-g4.dtsi | 74 +++++++---------- arch/arm/boot/dts/aspeed-g5.dtsi | 135 ++++++++++++++----------------- arch/arm/boot/dts/aspeed-g6.dtsi | 135 ++++++++++++++-----------------
I've booted a Witherspoon BMC and host with these patches applied, so for aspeed-g5.dtsi:
PATCH v5 3/5 ipmi: kcs: aspeed: Adapt to new LPC DTS layout
In reply to Chia-Wei, WangAdd check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
--- drivers/char/ipmi/kcs_bmc_aspeed.c | 27 ++++++++++++++++----------- 1 file changed, 16 insertions(+), 11 deletions(-)
drivers/char/ipmi/kcs_bmc_aspeed.c +16 -11
@@ -27,7 +27,6 @@#define KCS_CHANNEL_MAX 4 -/* mapped to lpc-bmc at 0 IO space */ #define LPC_HICR0 0x000#define LPC_HICR0_LPC3E BIT(7)#define LPC_HICR0_LPC2E BIT(6)
@@ -52,15 +51,13 @@#define LPC_STR1 0x03C#define LPC_STR2 0x040#define LPC_STR3 0x044 - -/* mapped to lpc-host at 80 IO space */ -#define LPC_HICRB 0x080 +#define LPC_HICRB 0x100#define LPC_HICRB_IBFIF4 BIT(1)#define LPC_HICRB_LPC4E BIT(0) -#define LPC_LADR4 0x090 -#define LPC_IDR4 0x094 -#define LPC_ODR4 0x098 -#define LPC_STR4 0x09C +#define LPC_LADR4 0x110 +#define LPC_IDR4 0x114 +#define LPC_ODR4 0x118 +#define LPC_STR4 0x11Cstruct aspeed_kcs_bmc {struct regmap *map;
@@ -348,12 +345,20 @@ static int aspeed_kcs_probe(struct platform_device *pdev)struct device_node *np;int rc; - np = pdev->dev.of_node; + np = dev->of_node->parent; +if (!of_device_is_compatible (np,"aspeed,ast2400-lpc-v2" ) && + !of_device_is_compatible (np,"aspeed,ast2500-lpc-v2" ) && + !of_device_is_compatible (np,"aspeed,ast2600-lpc-v2" )) { +dev_err (dev,"unsupported LPC device binding\n" ); +return -ENODEV ; + } + + np = dev->of_node;if (of_device_is_compatible (np,"aspeed,ast2400-kcs-bmc" ) || -of_device_is_compatible (np,"aspeed,ast2500-kcs-bmc" )) +of_device_is_compatible (np,"aspeed,ast2500-kcs-bmc" )) kcs_bmc =aspeed_kcs_probe_of_v1 (pdev);else if (of_device_is_compatible (np,"aspeed,ast2400-kcs-bmc-v2" ) || -of_device_is_compatible (np,"aspeed,ast2500-kcs-bmc-v2" )) +of_device_is_compatible (np,"aspeed,ast2500-kcs-bmc-v2" )) kcs_bmc =aspeed_kcs_probe_of_v2 (pdev);else return -EINVAL ;
Signature · 1 line
2.17.1
Re: [PATCH v5 3/5] ipmi: kcs: aspeed: Adapt to new LPC DTS layout
Quoted 6 lines · Wang
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
Signed-off-by Chia-Wei, Wang <[email protected]>Acked-by Haiyue Wang <[email protected]>
RE: [PATCH v5 3/5] ipmi: kcs: aspeed: Adapt to new LPC DTS layout
Hi Corey,
Could you help to review this patch to kcs_bmc_aspeed.c? It mainly fixes the register layout/offsets of Aspeed LPC controller.
Thanks,
Chiawei
Quoted 8 lines
-----Original Message-----
From: Andrew Jeffery <[email protected]>
Sent: Wednesday, January 20, 2021 1:03 PM
Subject: Re: [PATCH v5 3/5] ipmi: kcs: aspeed: Adapt to new LPC DTS layoutOn Thu, 14 Jan 2021, at 23:46, Chia-Wei, Wang wrote:
Quoted 8 lines
Quoted 6 lines
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted.
The LPC register offsets are also fixed accordingly.Signed-off-by Chia-Wei, Wang <[email protected]>Acked-by Haiyue Wang <[email protected]>Reviewed-by Andrew Jeffery <[email protected]>
Thanks for the review.
Corey Minyard
Acked-byRe: [PATCH v5 3/5] ipmi: kcs: aspeed: Adapt to new LPC DTS layout
Quoted 4 lines · ChiaWei Wang
Hi Corey,
Could you help to review this patch to
kcs_bmc_aspeed.c? It mainly fixes the register layout/offsets of Aspeed LPC controller.
I am not really qualified to review this. It looks ok from a structural and style point of view, but that's all I can tell. So I'm ok with it.
Quoted 22 lines
Thanks,
ChiaweiQuoted 8 lines
-----Original Message-----
From: Andrew Jeffery <[email protected]>
Sent: Wednesday, January 20, 2021 1:03 PM
Subject: Re: [PATCH v5 3/5] ipmi: kcs: aspeed: Adapt to new LPC DTS layoutOn Thu, 14 Jan 2021, at 23:46, Chia-Wei, Wang wrote:
Quoted 8 lines
Quoted 6 lines
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted.
The LPC register offsets are also fixed accordingly.Signed-off-by Chia-Wei, Wang <[email protected]>Acked-by Haiyue Wang <[email protected]>Reviewed-by Andrew Jeffery <[email protected]>Thanks for the review.
PATCH v5 4/5 pinctrl: aspeed-g5: Adapt to new LPC device tree layout
In reply to Chia-Wei, WangAdd check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
--- drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)
drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c +11 -6
@@ -60,7 +60,7 @@#define COND2 { ASPEED_IP_SCU, SCU94, GENMASK(1, 0), 0, 0 }/* LHCR0 is offset from the end of the H8S/2168-compatible registers */ -#define LHCR0 0x20 +#define LHCR0 0xa0#define GFX064 0x64#define B14 0
@@ -2648,14 +2648,19 @@ static struct regmap *aspeed_g5_acquire_regmap(struct aspeed_pinmux_data *ctx, }if (ip ==ASPEED_IP_LPC ) { -struct device_node *node; +struct device_node *np;struct regmap *map; - node =of_parse_phandle (ctx->dev->of_node, + np =of_parse_phandle (ctx->dev->of_node,"aspeed,external-nodes" ,1 ); -if (node) { - map =syscon_node_to_regmap (node->parent); -of_node_put (node); +if (np) { +if (!of_device_is_compatible (np->parent,"aspeed,ast2400-lpc-v2" ) && + !of_device_is_compatible (np->parent,"aspeed,ast2500-lpc-v2" ) && + !of_device_is_compatible (np->parent,"aspeed,ast2600-lpc-v2" )) +return ERR_PTR (-ENODEV ); + + map =syscon_node_to_regmap (np->parent); +of_node_put (np);if (IS_ERR (map))return map; }else
Signature · 1 line
2.17.1
Re: [PATCH v5 4/5] pinctrl: aspeed-g5: Adapt to new LPC device tree layout
Quoted 5 lines · Wang
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
Signed-off-by Chia-Wei, Wang <[email protected]>
I suppose the patches need to go in together. Tell me if you need me to apply this one patch to the pinctrl tree.
Yours,
Linus Walleij
Re: [PATCH v5 4/5] pinctrl: aspeed-g5: Adapt to new LPC device tree layout
In reply to Chia-Wei, WangQuoted 5 lines · Wang
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
Signed-off-by Chia-Wei, Wang <[email protected]>
Re: [PATCH v5 4/5] pinctrl: aspeed-g5: Adapt to new LPC device tree layout
In reply to Chia-Wei, WangQuoted 5 lines · Wang
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
Signed-off-by Chia-Wei, Wang <[email protected]>
Using a Witherspoon (AST2500):
PATCH v5 5/5 soc: aspeed: Adapt to new LPC device tree layout
In reply to Chia-Wei, WangAdd check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
--- drivers/soc/aspeed/aspeed-lpc-ctrl.c | 20 ++++++++++++++------ drivers/soc/aspeed/aspeed-lpc-snoop.c | 23 +++++++++++++++-------- 2 files changed, 29 insertions(+), 14 deletions(-)
drivers/soc/aspeed/aspeed-lpc-ctrl.c +14 -6
@@ -18,15 +18,15 @@#define DEVICE_NAME "aspeed-lpc-ctrl" -#define HICR5 0x0 +#define HICR5 0x80#define HICR5_ENL2H BIT(8)#define HICR5_ENFWH BIT(10) -#define HICR6 0x4 +#define HICR6 0x84#define SW_FWH2AHB BIT(17) -#define HICR7 0x8 -#define HICR8 0xc +#define HICR7 0x88 +#define HICR8 0x8cstruct aspeed_lpc_ctrl {struct miscdevice miscdev;
@@ -215,6 +215,7 @@ static int aspeed_lpc_ctrl_probe(struct platform_device *pdev)struct device_node *node;struct resource resm;struct device *dev; +struct device_node *np;int rc; dev = &pdev->dev;
@@ -270,8 +271,15 @@ static int aspeed_lpc_ctrl_probe(struct platform_device *pdev) } } - lpc_ctrl->regmap =syscon_node_to_regmap ( - pdev->dev.parent->of_node); + np = pdev->dev.parent->of_node; +if (!of_device_is_compatible (np,"aspeed,ast2400-lpc-v2" ) && + !of_device_is_compatible (np,"aspeed,ast2500-lpc-v2" ) && + !of_device_is_compatible (np,"aspeed,ast2600-lpc-v2" )) { +dev_err (dev,"unsupported LPC device binding\n" ); +return -ENODEV ; + } + + lpc_ctrl->regmap =syscon_node_to_regmap (np);if (IS_ERR (lpc_ctrl->regmap)) {dev_err (dev,"Couldn't get regmap\n" );return -ENODEV ;
drivers/soc/aspeed/aspeed-lpc-snoop.c +15 -8
@@ -28,26 +28,25 @@#define NUM_SNOOP_CHANNELS 2#define SNOOP_FIFO_SIZE 2048 -#define HICR5 0x0 +#define HICR5 0x80#define HICR5_EN_SNP0W BIT(0)#define HICR5_ENINT_SNP0W BIT(1)#define HICR5_EN_SNP1W BIT(2)#define HICR5_ENINT_SNP1W BIT(3) - -#define HICR6 0x4 +#define HICR6 0x84#define HICR6_STR_SNP0W BIT(0)#define HICR6_STR_SNP1W BIT(1) -#define SNPWADR 0x10 +#define SNPWADR 0x90#define SNPWADR_CH0_MASK GENMASK(15, 0)#define SNPWADR_CH0_SHIFT 0#define SNPWADR_CH1_MASK GENMASK(31, 16)#define SNPWADR_CH1_SHIFT 16 -#define SNPWDR 0x14 +#define SNPWDR 0x94#define SNPWDR_CH0_MASK GENMASK(7, 0)#define SNPWDR_CH0_SHIFT 0#define SNPWDR_CH1_MASK GENMASK(15, 8)#define SNPWDR_CH1_SHIFT 8 -#define HICRB 0x80 +#define HICRB 0x100#define HICRB_ENSNP0D BIT(14)#define HICRB_ENSNP1D BIT(15)
@@ -258,6 +257,7 @@ static int aspeed_lpc_snoop_probe(struct platform_device *pdev) {struct aspeed_lpc_snoop *lpc_snoop;struct device *dev; +struct device_node *np;u32 port;int rc;
@@ -267,8 +267,15 @@ static int aspeed_lpc_snoop_probe(struct platform_device *pdev)if (!lpc_snoop)return -ENOMEM ; - lpc_snoop->regmap =syscon_node_to_regmap ( - pdev->dev.parent->of_node); + np = pdev->dev.parent->of_node; +if (!of_device_is_compatible (np,"aspeed,ast2400-lpc-v2" ) && + !of_device_is_compatible (np,"aspeed,ast2500-lpc-v2" ) && + !of_device_is_compatible (np,"aspeed,ast2600-lpc-v2" )) { +dev_err (dev,"unsupported LPC device binding\n" ); +return -ENODEV ; + } + + lpc_snoop->regmap =syscon_node_to_regmap (np);if (IS_ERR (lpc_snoop->regmap)) {dev_err (dev,"Couldn't get regmap\n" );return -ENODEV ;
Signature · 1 line
2.17.1
PATCH v5 5/5 soc: aspeed: Adapt to new LPC device tree layout
Quoted 8 lines
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
Signed-off-by Chia-Wei, Wang <[email protected]>--- drivers/soc/aspeed/aspeed-lpc-ctrl.c | 20 ++++++++++++++------ drivers/soc/aspeed/aspeed-lpc-snoop.c | 23 +++++++++++++++--------
In the future please do separate patches for separate drivers, but for now:
Re: [PATCH v5 5/5] soc: aspeed: Adapt to new LPC device tree layout
In reply to Chia-Wei, WangQuoted 8 lines · Wang
Add check against LPC device v2 compatible string to ensure that the fixed device tree layout is adopted. The LPC register offsets are also fixed accordingly.
Signed-off-by Chia-Wei, Wang <[email protected]>--- drivers/soc/aspeed/aspeed-lpc-ctrl.c | 20 ++++++++++++++------ drivers/soc/aspeed/aspeed-lpc-snoop.c | 23 +++++++++++++++--------
Using a Witherspoon (AST2500) I've tested the aspeed-lpc-ctrl driver:
Thank you all for the reviewing effort.
Hi Joel,
Would you help to merge these patches into Aspeed tree?
If yes, we should also notify Linus Walleij to apply the pinctrl one to the pinctrl tree.
Thanks,
Chiawei
Quoted 60 lines
-----Original Message-----
From: ChiaWei Wang <[email protected]>
Sent: Thursday, January 14, 2021 9:16 PM
To: robh+dt at kernel.org; lee.jones at linaro.org; joel at jms.id.au; andrew at aj.id.au; linus.walleij at linaro.org; minyard at acm.org; devicetree at vger.kernel.org; linux-arm-kernel at lists.infradead.org; linux-aspeed at lists.ozlabs.org; linux-kernel at vger.kernel.org; openbmc at lists.ozlabs.org
Cc: BMC-SW <[email protected]>; haiyue.wang at linux.intel.com; cyrilbur at gmail.com; rlippert at google.com
Subject: [PATCH v5 0/5] Remove LPC register partitioningThe LPC controller has no concept of the BMC and the Host partitions. The incorrect partitioning can impose unnecessary range restrictions on register access through the syscon regmap interface.
For instance, HICRB contains the I/O port address configuration of KCS channel 1/2. However, the KCS#1/#2 drivers cannot access HICRB as it is located at the other LPC partition.
In addition, to be backward compatible, the newly added HW control bits could be located at any reserved bits over the LPC addressing space.
Thereby, this patch series aims to remove the LPC partitioning for better driver development and maintenance. This requires the change to both the device tree and the driver implementation. To ensure both sides are synchronously updated, a v2 binding check is added.
Chagnes since v4:
- Add child node example in dt-bindings.Chagnes since v3:
- Revise binding check as suggested by Haiyue Wang.Changes since v2:
- Add v2 binding check to ensure the synchronization between the device tree change and the driver register offset fix.Changes since v1:
- Add the fix to the aspeed-lpc binding documentation.Chia-Wei, Wang (5):
dt-bindings: aspeed-lpc: Remove LPC partitioning
ARM: dts: Remove LPC BMC and Host partitions
ipmi: kcs: aspeed: Adapt to new LPC DTS layout
pinctrl: aspeed-g5: Adapt to new LPC device tree layout
soc: aspeed: Adapt to new LPC device tree layout.../devicetree/bindings/mfd/aspeed-lpc.txt | 100 ++++--------- arch/arm/boot/dts/aspeed-g4.dtsi | 74 ++++------ arch/arm/boot/dts/aspeed-g5.dtsi | 135 ++++++++---------- arch/arm/boot/dts/aspeed-g6.dtsi | 135 ++++++++---------- drivers/char/ipmi/kcs_bmc_aspeed.c | 27 ++-- drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 17 ++- drivers/soc/aspeed/aspeed-lpc-ctrl.c | 20 ++- drivers/soc/aspeed/aspeed-lpc-snoop.c | 23 +-- 8 files changed, 229 insertions(+), 302 deletions(-)--
2.17.1