package/xenomai: smp support needs at least armv6
PATCH 1/2 package/xenomai: smp support needs at least armv6
There are no autobuilder failures for this issue, but the following defconfig:
BR2_arm=y
BR2_TOOLCHAIN_EXTERNAL=y
BR2_PACKAGE_XENOMAI=y
BR2_PACKAGE_XENOMAI_COBALT=y
--- package/xenomai/Config.in | 2 ++ 1 file changed, 2 insertions(+)
package/xenomai/Config.in +2 -0
@@ -110,6 +110,8 @@ endchoice config BR2_PACKAGE_XENOMAI_ENABLE_SMP bool "Enable SMP support" default y + # SMP not supported below armv6 + depends on !BR2_ARM_CPU_ARMV4 || !BR2_ARM_CPU_ARMV5 help This option enables SMP support in Xenomai userspace.
Signature · 1 line
2.29.2
PATCH 2/2 package/xenomai: disable cobalt for armv8
When a armv8 target is used in 32bits mode, xenomai fail to detect the ARM architecture and abord the build. (__ARM_ARCH_7A__ is not defined for armv8 cpus).
There are no autobuilder failures for this issue since cobalt is never selected, but the following defconfig:
BR2_arm=y
BR2_cortex_a53=y
BR2_ARM_FPU_NEON_VFPV4=y
BR2_TOOLCHAIN_EXTERNAL=y
BR2_PACKAGE_XENOMAI=y
BR2_PACKAGE_XENOMAI_COBALT=y
This was initialy reproduced using the raspberrypi3_defconfig with Xenomai package with cobalt selected.
In order to use Xenomai on raspberrypi3 in 32 bits mode, you have to select BR2_cortex_a7. This partially revert the commit a13a388dd444ee047f0e7b8c10f5e6c235ec5004.
--- package/xenomai/Config.in | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)
package/xenomai/Config.in +2 -2
@@ -1,8 +1,8 @@ config BR2_PACKAGE_XENOMAI_COBALT_ARCH_SUPPORTS bool default y - depends on BR2_i386 || BR2_x86_64 || (BR2_arm && !BR2_ARM_CPU_ARMV7M) || \ - BR2_powerpc + depends on BR2_i386 || BR2_x86_64 || BR2_powerpc || \ + (BR2_arm && !BR2_ARM_CPU_ARMV7M && !BR2_ARM_CPU_ARMV8A) comment "xenomai needs a glibc or uClibc toolchain w/ threads" depends on BR2_USE_MMU
Signature · 1 line
2.29.2
Yann E. MORIN
AppliedPATCH 2/2 package/xenomai: disable cobalt for armv8
Romain, All,
On 2021-02-02 21:56 +0100, Romain Naour spake thusly:
Quoted 34 lines
When a armv8 target is used in 32bits mode, xenomai fail to detect the ARM architecture and abord the build. (
__ARM_ARCH_7A__is not defined for armv8 cpus).There are no autobuilder failures for this issue since cobalt is never selected, but the following defconfig:
BR2_arm=y
BR2_cortex_a53=y
BR2_ARM_FPU_NEON_VFPV4=y
BR2_TOOLCHAIN_EXTERNAL=y
BR2_PACKAGE_XENOMAI=y
BR2_PACKAGE_XENOMAI_COBALT=yThis was initialy reproduced using the
raspberrypi3_defconfigwith Xenomai package with cobalt selected.In order to use Xenomai on raspberrypi3 in 32 bits mode, you have to select
BR2_cortex_a7. This partially revert the commita13a388dd444ee047f0e7b8c10f5e6c235ec5004.Signed-off-by Romain Naour <[email protected]>--- package/xenomai/Config.in | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)package/xenomai/Config.in +0
-0
package/xenomai/Config.in line 5
Quoted 7 lines
package/xenomai/Config.in +2
-2@@ -1,8 +1,8 @@ config BR2_PACKAGE_XENOMAI_COBALT_ARCH_SUPPORTS bool default y - depends on BR2_i386 || BR2_x86_64 || (BR2_arm && !BR2_ARM_CPU_ARMV7M) || \ - BR2_powerpc + depends on BR2_i386 || BR2_x86_64 || BR2_powerpc || \ + (BR2_arm && !BR2_ARM_CPU_ARMV7M && !BR2_ARM_CPU_ARMV8A)
This condition is starting to look pretty ugly, now... I've changed that to a series of conditional 'default y if $ARCH' statements instead.
Applied to master, thanks.
Regards,
Yann E. MORIN.
Quoted 9 lines
package/xenomai/Config.in +0
-0comment "xenomai needs a glibc or uClibc toolchain w/ threads" depends on BR2_USE_MMUSignature · 6 lines
2.29.2 _______________________________________________ buildroot mailing list buildroot at busybox.net http://lists.busybox.net/mailman/listinfo/buildroot
Signature · 6 lines
.-----------------.--------------------.------------------.--------------------. | Yann E. MORIN | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: | | +33 662 376 056 | Software Designer | \ / CAMPAIGN | ___ | | +33 561 099 427 `------------.-------: X AGAINST | \e/ There is no | | http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL | v conspiracy. | '------------------------------^-------^------------------^--------------------'
PATCH 2/2 package/xenomai: disable cobalt for armv8
In reply to Romain NaourQuoted 19 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Romain" == Romain Naour <[email protected]> writes:
When a armv8 target is used in 32bits mode, xenomai fail to detect the ARM architecture and abord the build. (
__ARM_ARCH_7A__is not defined for armv8 cpus).There are no autobuilder failures for this issue since cobalt is never selected, but the following defconfig:
BR2_arm=y
BR2_cortex_a53=y
BR2_ARM_FPU_NEON_VFPV4=y
BR2_TOOLCHAIN_EXTERNAL=y
BR2_PACKAGE_XENOMAI=y
BR2_PACKAGE_XENOMAI_COBALT=yThis was initialy reproduced using the
raspberrypi3_defconfigwith Xenomai package with cobalt selected.
Quoted 8 lines
In order to use Xenomai on raspberrypi3 in 32 bits mode, you have to select
BR2_cortex_a7. This partially revert the commita13a388dd444ee047f0e7b8c10f5e6c235ec5004.Signed-off-by Romain Naour <[email protected]>
Committed to 2020.02.x and 2020.11.x, thanks.
Signature · 1 line
Bye, Peter Korsgaard
Yann E. MORIN
AppliedPATCH 1/2 package/xenomai: smp support needs at least armv6
In reply to Romain NaourRomain, All,
On 2021-02-02 21:56 +0100, Romain Naour spake thusly:
Quoted 21 lines
There are no autobuilder failures for this issue, but the following defconfig:
BR2_arm=y
BR2_TOOLCHAIN_EXTERNAL=y
BR2_PACKAGE_XENOMAI=y
BR2_PACKAGE_XENOMAI_COBALT=ySigned-off-by Romain Naour <[email protected]>--- package/xenomai/Config.in | 2 ++ 1 file changed, 2 insertions(+)package/xenomai/Config.in +0
-0
package/xenomai/Config.in endchoice · line 114
Quoted 5 lines
package/xenomai/Config.in +2
-0@@ -110,6 +110,8 @@ endchoice config BR2_PACKAGE_XENOMAI_ENABLE_SMP bool "Enable SMP support" default y + # SMP not supported below armv6 + depends on !BR2_ARM_CPU_ARMV4 || !BR2_ARM_CPU_ARMV5
This does not make sense:
- if you are using armv4, then you are not using armv5, and thus the
condition is true;
- if you are using armv5, then you are not using armv4, and thus the
condition is true;
- if you are using neither armv4 nor armv5, then the condition is true.
So, the condition is always true...
I've changed that to:
depends on !BR2_ARM_CPU_ARMV4 && !BR2_ARM_CPU_ARMV5
Applied to master with that fixed, thanks.
Regards,
Yann E. MORIN.
Quoted 10 lines
package/xenomai/Config.in +0
-0help This option enables SMP support in Xenomai userspace.Signature · 6 lines
2.29.2 _______________________________________________ buildroot mailing list buildroot at busybox.net http://lists.busybox.net/mailman/listinfo/buildroot
Signature · 6 lines
.-----------------.--------------------.------------------.--------------------. | Yann E. MORIN | Real-Time Embedded | /"\ ASCII RIBBON | Erics' conspiracy: | | +33 662 376 056 | Software Designer | \ / CAMPAIGN | ___ | | +33 561 099 427 `------------.-------: X AGAINST | \e/ There is no | | http://ymorin.is-a-geek.org/ | _/*\_ | / \ HTML MAIL | v conspiracy. | '------------------------------^-------^------------------^--------------------'
PATCH 1/2 package/xenomai: smp support needs at least armv6
In reply to Romain NaourQuoted 10 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Romain" == Romain Naour <[email protected]> writes:
There are no autobuilder failures for this issue, but the following defconfig:
BR2_arm=y
BR2_TOOLCHAIN_EXTERNAL=y
BR2_PACKAGE_XENOMAI=y
BR2_PACKAGE_XENOMAI_COBALT=y
Quoted 4 lines
Signed-off-by Romain Naour <[email protected]>
Committed to 2020.02.x and 2020.11.x, thanks.
Signature · 1 line
Bye, Peter Korsgaard