DTS updates for Marvell Armada CN913x platforms
Subsystems (3)
v4 cover DTS updates for Marvell Armada CN913x platforms
From: Konstantin Porotchkin <[email protected]>
This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB)
3. Fixes the CP11X references in PHY binding document
4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions
All above changes are already intergated into Marvell official SDK sources
v2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is added
- mention the switch part ID in CRB board description
v3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include names
v4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platforms
Grzegorz Jaszczyk (1):
Documentation/bindings: phy: update references to cp11x
Konstantin Porotchkin (3):
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
arm64: dts: cn913x: add device trees for topology B boards
arm64: dts: add support for Marvell cn9130-crb platform
Stefan Chulski (1):
dts: marvell: Enable 10G interface on 9130-DB board
.../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 1/5 Documentation/bindings: phy: update references to cp11x
From: Grzegorz Jaszczyk <[email protected]>
The cp11x references in dts has changed, reflect it in comphy documentation.
--- Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-)
Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt +6 -6
@@ -42,22 +42,22 @@ Required properties (child nodes): Examples: - cpm_comphy: phy@120000 { + CP11X_LABEL(comphy): phy@120000 { compatible = "marvell,comphy-cp110"; reg = <0x120000 0x6000>; - marvell,system-controller = <&cpm_syscon0>; - clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>, - <&CP110_LABEL(clk) 1 18>; + marvell,system-controller = <&CP11X_LABEL(syscon0)>; + clocks = <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>, + <&CP11X_LABEL(clk) 1 18>; clock-names = "mg_clk", "mg_core_clk", "axi_clk"; #address-cells = <1>; #size-cells = <0>; - cpm_comphy0: phy@0 { + CP11X_LABEL(comphy0): phy@0 { reg = <0>; #phy-cells = <1>; }; - cpm_comphy1: phy@1 { + CP11X_LABEL(comphy1): phy@1 { reg = <1>; #phy-cells = <1>; };
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 2/5 arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
In reply to [email protected]From: Konstantin Porotchkin <[email protected]>
Eliminate 1MB gap between Linux and filesystem partitions.
--- arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/marvell/cn9130-db.dts +1 -1
@@ -258,7 +258,7 @@ }; partition@200000 { label = "Linux"; - reg = <0x200000 0xd00000>; + reg = <0x200000 0xe00000>; }; partition@1000000 { label = "Filesystem";
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 3/5 arm64: dts: cn913x: add device trees for topology B boards
In reply to [email protected]From: Konstantin Porotchkin <[email protected]>
The CN913x DB with topology B is similar to a regular setup (A) boards, but uses NAND flash as a boot device, while topology A boards are booting from SPI flash.
Since NAND and SPI on CN913x DB boards share some wires, they cannot be activated simultaneously.
The DTS files for setup "B" are based on setup "A", in which the CP0 NAND controller enabled and CP0 SPI1 disabled.
--- arch/arm64/boot/dts/marvell/Makefile | 3 + arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +------------------ arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +--------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 ++++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 ++ arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +--------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 +++++++++++ 10 files changed, 910 insertions(+), 778 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
arch/arm64/boot/dts/marvell/Makefile +3 -0
@@ -16,5 +16,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin-singleshot.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-puzzle-m801.dtb dtb-$(CONFIG_ARCH_MVEBU) += armada-8080-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
arch/arm64/boot/dts/marvell/cn9130-db-B.dts new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9130-DB board (setup "B"). + */ + +#include "cn9130-db.dtsi" + +/ { + model = "Marvell Armada CN9130-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; +
arch/arm64/boot/dts/marvell/cn9130-db.dts +6 -387
405 lines not on this page · raw message
arch/arm64/boot/dts/marvell/cn9130-db.dtsi new file +402 -0
402 lines not on this page · raw message
arch/arm64/boot/dts/marvell/cn9131-db-B.dts new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Marvell International Ltd. + * + * Device tree for the CN9131-DB board (setup "B"). + */ + +#include "cn9131-db.dtsi" + +/ { + model = "Marvell Armada CN9131-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; +
arch/arm64/boot/dts/marvell/cn9131-db.dts +6 -186
204 lines not on this page · raw message
arch/arm64/boot/dts/marvell/cn9131-db.dtsi new file +201 -0
201 lines not on this page · raw message
arch/arm64/boot/dts/marvell/cn9132-db-B.dts new file +22 -0
@@ -0,0 +1,22 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2019 Marvell International Ltd. + * + * Device tree for the CN9132-DB board. + */ + +#include "cn9132-db.dtsi" + +/ { + model = "Marvell Armada CN9132-DB setup B"; +}; + +/* Setup B has NAND flash as a boot device, while regular setup uses SPI flash. + * Since CP0 SPI1 and CP0 NAND are sharing some pins, they cannot be activated + * simultaneously. When NAND controller is enabled, SPI1 should be disabled. + */ + +&cp0_nand_controller { + status = "okay"; +}; +
arch/arm64/boot/dts/marvell/cn9132-db.dts +6 -205
223 lines not on this page · raw message
arch/arm64/boot/dts/marvell/cn9132-db.dtsi new file +220 -0
220 lines not on this page · raw message
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 4/5 dts: marvell: Enable 10G interface on 9130-DB board
In reply to [email protected]From: Stefan Chulski <[email protected]>
This patch enables eth0 10G interface on CN9130-DB paltforms.
--- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/marvell/cn9130-db.dtsi +1 -1
@@ -125,7 +125,7 @@ /* SLM-1521-V2, CON9 */ &cp0_eth0 { - status = "disabled"; + status = "okay"; phy-mode = "10gbase-kr"; /* Generic PHY, providing serdes lanes */ phys = <&cp0_comphy4 0>;
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v4 4/5] dts: marvell: Enable 10G interface on 9130-DB board
Hi,
wt., 9 lut 2021 o 14:47 <[email protected]> napisał(a):
Quoted 25 lines
From: Stefan Chulski <[email protected]>
This patch enables eth0 10G interface on CN9130-DB paltforms.
Signed-off-by Stefan Chulski <[email protected]>Signed-off-by Konstantin Porotchkin <[email protected]>--- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)arch/arm64/boot/dts/marvell/cn9130-db.dtsi +1
-2@@ -125,7 +125,7 @@ /* SLM-1521-V2, CON9 */ &cp0_eth0 { - status = "disabled"; + status = "okay"; phy-mode = "10gbase-kr"; /* Generic PHY, providing serdes lanes */ phys = <&cp0_comphy4 0>; --
Quoted 2 lines
2.17.1
You can add my:
Please do the same for cp1_eth0?
Best regards,
Marcin
PATCH v4 5/5 arm64: dts: add support for Marvell cn9130-crb platform
In reply to [email protected]From: Konstantin Porotchkin <[email protected]>
The Marvell reference platform CN9130-CRB is a small form factor board in a metal case. The platform is based on CN9130 SoC with addition of 8 Gigabit ports SOHO Ethernet switch.
The reference platform features the following:
* Up to 4 CPU cores ARMv8 Cortex-A72 CPU
* CPU core operating speed of up to 2.2GHz
* DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz.
* 1x eMMC 8GB device
* 1x uSD card 4 bits port on CP
* 1x 128MB SPI NOR flash memory
* 1x USB 3.0 Host port (Type A)
* 1x SATA Gen3 via M.2
* 1x USB 3.0 via M.2
* 1x SIM card slot
* 1x 1G Ethernet port via RGMII
* 1x 10G switch port over SFP+ connector
* 8x 1G ports through 88E6393X switch via XFI
* 1x 2.5G/1G/100M/10M port via HS_SGMII
* 1x PCI Express (PCIe)x1 Gen 3.0
* 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2
* JTAG port
The CRB board uses MCP23017 i2c pin controller that drives the onboard eMMC abd USB 3,0 port power lines.
The following configuration should be enabled for this controller support:CONFIG_PINCTRL_MCP23S08=y
The plaform supports two HW configurations - "A" and "B" CN9130-CRB-A
* AP-MPP configuration: SDIO, UART
* CP0 Serdes configuration:
* Lane0-3: NVMe (PCIe x4)
* Lane4: XFI
* Lane5: HS_SGMII
2. CN9130-CRB-B
* AP-MPP configuration: SDIO, UART
* CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI
* CP0 Serdes configuration:
* Lane0: PCIe x1
* Lane1: USB3_0 x1
* Lane2: SATA x1
* Lane3: USB3_1 x1
* Lane4: XFI
* Lane5: HS_SGMII
--- arch/arm64/boot/dts/marvell/Makefile | 2 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 222 ++++++++++++++++++++ 4 files changed, 308 insertions(+) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
arch/arm64/boot/dts/marvell/Makefile +2 -0
@@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb +dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
arch/arm64/boot/dts/marvell/cn9130-crb-A.dts new file +38 -0
@@ -0,0 +1,38 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2020 Marvell International Ltd. + */ + +#include "cn9130-crb.dtsi" + +/ { + model = "Marvell Armada CN9130-CRB-A"; +}; + +&cp0_pcie0 { + status = "okay"; + num-lanes = <4>; + num-viewport = <8>; + /* Generic PHY, providing serdes lanes */ + phys = <&cp0_comphy0 0 + &cp0_comphy1 0 + &cp0_comphy2 0 + &cp0_comphy3 0>; + iommu-map = + <0x0 &smmu 0x480 0x20>, + <0x100 &smmu 0x4a0 0x20>, + <0x200 &smmu 0x4c0 0x20>; + iommu-map-mask = <0x031f>; +}; + +&cp0_usb3_0 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy0>; + phy-names = "usb"; +}; + +&cp0_usb3_1 { + status = "okay"; + usb-phy = <&cp0_usb3_0_phy1>; + phy-names = "usb"; +};
arch/arm64/boot/dts/marvell/cn9130-crb-B.dts new file +46 -0
46 lines not on this page · raw message
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi new file +222 -0
222 lines not on this page · raw message
Signature · 7 lines
2.17.1 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Gregory CLEMENT
maintainerHello,
Quoted 30 lines
From: Konstantin Porotchkin <[email protected]>
This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB)
3. Fixes the CP11X references in PHY binding document
4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions
All above changes are already intergated into Marvell official SDK sourcesv2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is added
- mention the switch part ID in CRB board descriptionv3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include namesv4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platformsGrzegorz Jaszczyk (1):
Documentation/bindings: phy: update references to cp11x
Quoted 8 lines
Konstantin Porotchkin (3):
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
arm64: dts: cn913x: add device trees for topology B boards
arm64: dts: add support for Marvell cn9130-crb platformStefan Chulski (1):
dts: marvell: Enable 10G interface on 9130-DB board
I've applied patches 1 and 2, but I have issue with patch 3, there was some changes around the phys and I am not sure of the correct way to modify the patch.
Could you rebase it on v5.13-c1 and fix the merge issue ?
Thanks,
Gregory
Quoted 28 lines
.../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsiSignature · 1 line
2.17.1
Signature · 3 lines
Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com
Hi, Gregory,
The last series was v5. I will rebase on top of Linus 5.13-rcx and then post new v6 set.
Regards
Kosta
Quoted 108 lines
-----Original Message-----
From: Gregory CLEMENT <[email protected]>
Sent: Thursday, June 17, 2021 18:40
To: Kostya Porotchkin <[email protected]>; [email protected]; [email protected]; [email protected]
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; Nadav Haklai <[email protected]>; Stefan Chulski <[email protected]>; Ben Peled <[email protected]>; Kostya Porotchkin <[email protected]>
Subject: [EXT] Re: [PATCH v4 0/5] DTS updates for Marvell Armada CN913x platformsExternal Email
----------------------------------------------------------------------
Hello,Quoted 32 lines
From: Konstantin Porotchkin <[email protected]>
This patch series contains the following changes/fixes:
1. Add support for Armada CN913x Development Board topology "B"
2. Add support for Armada CN913x Reference Design boards (CRB) 3. Fixes the CP11X references in PHY binding document 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between consecutive partitions All above changes are already intergated into Marvell official SDK sourcesv2:
- extract common nodes from DB boards to separate DTSI files
- disable eth2 on CRB boards until the required phy mode support is added
- mention the switch part ID in CRB board descriptionv3:
- do not rename setup A DTS files for DB variants
- fix a couple of wrong include namesv4:
- Rebase on top of Linus master branch (v5.11-rc7)
- Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
- Add cd-gpio entry to CP0 SDHCI for SD card support
- Add a comment to CN9130-CRB patch about the required defconfig changes for supporting the onboard i2c expander
- Add Stefan's patch to enable 10G port on CN9130-DB platformsGrzegorz Jaszczyk (1):
Documentation/bindings: phy: update references to cp11xQuoted 8 lines
Konstantin Porotchkin (3):
arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
arm64: dts: cn913x: add device trees for topology B boards
arm64: dts: add support for Marvell cn9130-crb platformStefan Chulski (1):
dts: marvell: Enable 10G interface on 9130-DB boardI've applied patches 1 and 2, but I have issue with patch 3, there was some changes around the phys and I am not sure of the correct way to modify the patch.
Could you rebase it on v5.13-c1 and fix the merge issue ?
Thanks,
Gregory
Quoted 25 lines
.../bindings/phy/phy-mvebu-comphy.txt | 12 +- arch/arm64/boot/dts/marvell/Makefile | 5 + arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 221 ++++++++++ arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9130-db.dts | 393 +---------------- arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 402 ++++++++++++++++++ arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9131-db.dts | 192 +-------- arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 201 +++++++++ arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + arch/arm64/boot/dts/marvell/cn9132-db.dts | 211 +-------- arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 220 ++++++++++ 14 files changed, 1223 insertions(+), 784 deletions(-) create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsiQuoted 3 lines
--
2.17.1--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
https://urldefense.proofpoint.com/v2/url?u=http-
3A__bootlin.com&d=DwIBAg&c=nKjWec2b6R0mOyPaz7xtfQ&r=- N9sN4p5NSr0JGQoQ_2UCOgAqajG99W1EbSOww0WU8o&m=yb2JOcVicfAZRe thZJoDE- wbwtupb3tk_D7VGKCNsqc&s=4oskkLywYJujfGQ4XpFfP6n4ybkC0722K_8qH3xz bK8&e=