Add peripheral support for imx8mm-nitrogen-r2 board

PATCH Applied Adrien Grassein 3 participants 15 messages Feb 23, 2021 – Mar 8, 2021

Subsystems (2)

Device tree bindings Arm i.MX and Layerscape

lore

Share & tools

lore

Adrien Grassein

author

2021-02-23 19:17 UTC #0 lore raw

v4 cover Add peripheral support for imx8mm-nitrogen-r2 board

Hi,

this patch set is to add several peripheral support for the imx8mm-nitrogen-r2 board.

Thanks,

Update in v2:
- Fix some typo found in v1;
- Fix UART description

Update in v3
- Fix wlan vqmcc regulator;
- Remove useless clock node;
- Split UART patch

Update in v4
- Fix audio binding;
- Add a patch to fix eMMC binding.

Thanks,

Adrien Grassein (10):
arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip
arm64: dts: imx8mm-nitrogen-r2: rework USDHC1
arm64: dts: imx8mm-nitrogen-r2: add USB support
arm64: dts: imx8mm-nitrogen-r2: add espi2 support
arm64: dts: imx8mm-nitrogen-r2: add UARTs
arm64: dts: imx8mm-nitrogen-r2: rework UART 2
arm64: dts: imx8mm-nitrogen-r2: add PWMs
arm64: dts: imx8mm-nitrogen-r2: add FlexSPI
arm64: dts: imx8mm-nitrogen-r2: add audio
arm64: defconfig: Enable wm8960 audio driver.

 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 314 +++++++++++++++++-
 arch/arm64/configs/defconfig                  |   1 +
 2 files changed, 313 insertions(+), 2 deletions(-)

Signature · 1 line

2.25.1

Adrien Grassein

author

2021-02-23 19:17 UTC #1 lore raw

PATCH v4 1/10 arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip

Add usdhc3 description which corresponds to the wifi/bt chip

Signed-off-by Adrien Grassein <[email protected]>

---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +38 -0

index c0c384d76147..4a3dabeb8c85 100644
@@ -9,6 +9,24 @@
 / {
 	model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2";
 	compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm";
+
+	reg_vref_1v8: regulator-vref-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_wlan_vmmc: regulator-wlan-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_wlan_vmmc>;
+		regulator-name = "reg_wlan_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 &A53_0 {

@@ -206,6 +224,20 @@ &usdhc2 {
 	status = "okay";
 };
 
+/* wlan */
+&usdhc3 {
+	bus-width = <4>;
+	sdhci-caps-mask = <0x2 0x0>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	vmmc-supply = <&reg_wlan_vmmc>;
+	vqmmc-supply = <&reg_vref_1v8>;
+	status = "okay";
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;

@@ -264,6 +296,12 @@ MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0
 		>;
 	};
 
+	pinctrl_reg_wlan_vmmc: reg-wlan-vmmcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x16
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140

Signature · 1 line

2.25.1

Krzysztof Kozlowski

Reviewed-by on v4 1/10

2021-02-23 19:55 UTC #2 lore raw

Re: [PATCH v4 01/10] arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip

Quoted 7 lines · Adrien Grassein

Add usdhc3 description which corresponds to the wifi/bt chip
Signed-off-by Adrien Grassein <[email protected]>
---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

Reviewed-by Krzysztof Kozlowski <[email protected]>

Best regards,
Krzysztof

Adrien Grassein

author

2021-02-23 19:17 UTC #3 lore raw

PATCH v4 2/10 arm64: dts: imx8mm-nitrogen-r2: rework USDHC1

In reply to Adrien Grassein

Add VMMC and VQMMC description for USDHC1 (eMMC).
There are comming directly from the alimentation
stage, so add the vref_3V3 fixed regulator.

Signed-off-by Adrien Grassein <[email protected]>

---
 arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts | 9 +++++++++
 1 file changed, 9 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +9 -0

index 4a3dabeb8c85..217ac8c53702 100644
@@ -17,6 +17,13 @@ reg_vref_1v8: regulator-vref-1v8 {
 		regulator-max-microvolt = <1800000>;
 	};
 
+	reg_vref_3v3: regulator-vref-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_wlan_vmmc: regulator-wlan-vmmc {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";

@@ -209,6 +216,8 @@ &usdhc1 {
 	pinctrl-0 = <&pinctrl_usdhc1>;
 	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
 	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_vref_3v3>;
+	vqmmc-supply = <&reg_vref_1v8>;
 	status = "okay";
 };

Signature · 1 line

2.25.1

Adrien Grassein

author

2021-02-23 19:17 UTC #4 lore raw

PATCH v4 3/10 arm64: dts: imx8mm-nitrogen-r2: add USB support

In reply to Adrien Grassein

Add description of USB.
usbotg2 seems to not working on all boards (including ones from variscite).

Signed-off-by Adrien Grassein <[email protected]>

Reviewed-by Krzysztof Kozlowski <[email protected]>

---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 42 +++++++++++++++++++
 1 file changed, 42 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +42 -0

index 217ac8c53702..4f4cf7df5a5a 100644
@@ -247,6 +247,34 @@ &usdhc3 {
 	status = "okay";
 };
 
+/* USB OTG port */
+&usbotg1 {
+	dr_mode = "otg";
+	over-current-active-low;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	power-active-high;
+	status = "okay";
+};
+
+/* USB Host port */
+&usbotg2 {
+	dr_mode = "host";
+	over-current-active-low;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	power-active-high;
+	/*
+	 * FIXME: having USB2 enabled hangs the boot just after:
+	 *[    1.655941] ci_hdrc ci_hdrc.1: EHCI Host Controller
+	 *[    1.660880] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2
+	 *[    1.681505] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00
+	 *[    1.687730] hub 2-0:1.0: USB hub found
+	 *[    1.691528] hub 2-0:1.0: 1 port detected
+	 */
+	status = "disabled";
+};
+
 &wdog1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_wdog>;

@@ -318,6 +346,20 @@ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
 		>;
 	};
 
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x16
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC	0x156
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO14_USB2_OTG_PWR	0x16
+			MX8MM_IOMUXC_GPIO1_IO15_USB2_OTG_OC	0x15
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x190

Signature · 1 line

2.25.1

Adrien Grassein

author

2021-02-23 19:18 UTC #5 lore raw

PATCH v4 5/10 arm64: dts: imx8mm-nitrogen-r2: add UARTs

In reply to Adrien Grassein

Add description and pin muxing for UARTs.

Signed-off-by Adrien Grassein <[email protected]>

Reviewed-by Krzysztof Kozlowski <[email protected]>

---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 48 +++++++++++++++++++
 1 file changed, 48 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +48 -0

index 0c5949b40eeb..1b16d09fa887 100644
@@ -211,6 +211,14 @@ rtc@68 {
 	};
 };
 
+/* BT */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
 /* console */
 &uart2 {
 	pinctrl-names = "default";

@@ -220,6 +228,21 @@ &uart2 {
 	status = "okay";
 };
 
+/* J15 */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* J9 */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
 /* eMMC */
 &usdhc1 {
 	bus-width = <8>;

@@ -361,6 +384,15 @@ MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x16
 		>;
 	};
 
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140
+			MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140
+			MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140
+		>;
+	};
+
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140

@@ -368,6 +400,22 @@ MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
 		>;
 	};
 
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x140
+			MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x140
+			MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x140
+			MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x140
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140
+		>;
+	};
+
 	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x16

Signature · 7 lines

2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Adrien Grassein

author

2021-02-23 19:18 UTC #6 lore raw

PATCH v4 6/10 arm64: dts: imx8mm-nitrogen-r2: rework UART 2

In reply to Adrien Grassein

Remove useless clocks in UART 2

Signed-off-by Adrien Grassein <[email protected]>

Reviewed-by Krzysztof Kozlowski <[email protected]>

---
 arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts | 2 --
 1 file changed, 2 deletions(-)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +0 -2

index 1b16d09fa887..e44c5963040d 100644
@@ -223,8 +223,6 @@ &uart1 {
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
-	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
-	assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
 	status = "okay";
 };

Signature · 7 lines

2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Adrien Grassein

author

2021-02-23 19:18 UTC #7 lore raw

PATCH v4 7/10 arm64: dts: imx8mm-nitrogen-r2: add PWMs

In reply to Adrien Grassein

Add description for the four PWMs.

Signed-off-by Adrien Grassein <[email protected]>

Reviewed-by Krzysztof Kozlowski <[email protected]>

---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 51 +++++++++++++++++++
 1 file changed, 51 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +51 -0

index e44c5963040d..cabcd6f19d56 100644
@@ -211,6 +211,33 @@ rtc@68 {
 	};
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	assigned-clocks = <&clk IMX8MM_CLK_PWM2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_40M>;
+	assigned-clock-rates = <40000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
 /* BT */
 &uart1 {
 	pinctrl-names = "default";

@@ -376,6 +403,30 @@ MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0
 		>;
 	};
 
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT 0x16
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT 0x16
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT 0x16
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_MCLK_PWM4_OUT 0x16
+		>;
+	};
+
 	pinctrl_reg_wlan_vmmc: reg-wlan-vmmcgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x16

Signature · 7 lines

2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Adrien Grassein

author

2021-02-23 19:18 UTC #8 lore raw

PATCH v4 8/10 arm64: dts: imx8mm-nitrogen-r2: add FlexSPI

In reply to Adrien Grassein

Add FlexSPI description an pin muxing.

Signed-off-by Adrien Grassein <[email protected]>

Reviewed-by Krzysztof Kozlowski <[email protected]>

---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts   | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +17 -0

index cabcd6f19d56..c13788e6c0d9 100644
@@ -85,6 +85,12 @@ ethphy0: ethernet-phy@4 {
 	};
 };
 
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi>;
+	status = "okay";
+};
+
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";

@@ -376,6 +382,17 @@ MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x159
 		>;
 	};
 
+	pinctrl_flexspi: flexspigrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK	0x1c2
+			MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82
+			MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82
+			MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82
+			MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82
+			MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82
+		>;
+	};
+
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x09

Signature · 7 lines

2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Adrien Grassein

author

2021-02-23 19:18 UTC #9 lore raw

PATCH v4 9/10 arm64: dts: imx8mm-nitrogen-r2: add audio

In reply to Adrien Grassein

Add audio description and pin muxing.

Signed-off-by Adrien Grassein <[email protected]>

---
 .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 85 +++++++++++++++++++
 1 file changed, 85 insertions(+)

arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts +85 -0

index c13788e6c0d9..b6775f832907 100644
@@ -34,6 +34,28 @@ reg_wlan_vmmc: regulator-wlan-vmmc {
 		gpio = <&gpio3 20 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
+
+	sound-wm8960 {
+		audio-cpu = <&sai1>;
+		audio-codec = <&wm8960>;
+		audio-routing =
+			"Headphone Jack", "HP_L",
+			"Headphone Jack", "HP_R",
+			"Ext Spk", "SPK_LP",
+			"Ext Spk", "SPK_LN",
+			"Ext Spk", "SPK_RP",
+			"Ext Spk", "SPK_RN",
+			"RINPUT1", "Mic Jack",
+			"Mic Jack", "MICB";
+		compatible = "fsl,imx-audio-wm8960";
+		/* JD2: hp detect high for headphone*/
+		hp-det-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		/* Jack is not stuffed */
+		mic-det-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		model = "wm8960-audio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sound_wm8960>;
+	};
 };
 
 &A53_0 {

@@ -217,6 +239,22 @@ rtc@68 {
 	};
 };
 
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	wm8960: codec@1a {
+		compatible = "wlf,wm8960";
+		reg = <0x1a>;
+		clocks = <&clk IMX8MM_CLK_SAI1_ROOT>;
+		clock-names = "mclk1";
+		wlf,shared-lrclk;
+		#sound-dai-cells = <0>;
+	};
+};
+
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;

@@ -244,6 +282,18 @@ &pwm4 {
 	status = "okay";
 };
 
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	status = "okay";
+};
+
+&sai2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	status = "okay";
+};
+
 /* BT */
 &uart1 {
 	pinctrl-names = "default";

@@ -414,6 +464,13 @@ MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
 		>;
 	};
 
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3
+		>;
+	};
+
 	pinctrl_i2c3a_rv4162: i2c3a-rv4162grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0

@@ -450,6 +507,34 @@ MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20 0x16
 		>;
 	};
 
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			/* wm8960 */
+			MX8MM_IOMUXC_SAI1_MCLK_SAI1_MCLK	0xd6
+			MX8MM_IOMUXC_SAI1_TXFS_SAI1_TX_SYNC	0xd6
+			MX8MM_IOMUXC_SAI1_TXC_SAI1_TX_BCLK	0xd6
+			MX8MM_IOMUXC_SAI1_TXD0_SAI1_TX_DATA0	0xd6
+			MX8MM_IOMUXC_SAI1_RXD0_SAI1_RX_DATA0	0xd6
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			/* Bluetooth PCM */
+			MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC	0xd6
+			MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK	0xd6
+			MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0	0xd6
+			MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0	0xd6
+		>;
+	};
+
+	pinctrl_sound_wm8960: sound-wm8960grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x80
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28	0x80
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140

Signature · 1 line

2.25.1

Adrien Grassein

author

2021-02-23 19:18 UTC #10 lore raw

PATCH v4 10/10 arm64: defconfig: Enable wm8960 audio driver.

In reply to Adrien Grassein

This driver is used by the Nitrogen8m Mini SBC.

Signed-off-by Adrien Grassein <[email protected]>

Reviewed-by Krzysztof Kozlowski <[email protected]>

---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

arch/arm64/configs/defconfig +1 -0

index 292c00f893fc..bd310e91d4ed 100644
@@ -764,6 +764,7 @@ CONFIG_SND_SOC_SIMPLE_AMPLIFIER=m
 CONFIG_SND_SOC_TAS571X=m
 CONFIG_SND_SOC_WCD934X=m
 CONFIG_SND_SOC_WM8904=m
+CONFIG_SND_SOC_WM8960=m
 CONFIG_SND_SOC_WM8962=m
 CONFIG_SND_SOC_WSA881X=m
 CONFIG_SND_SOC_LPASS_WSA_MACRO=m

Signature · 7 lines

2.25.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Shawn Guo

Applied

2021-03-08 00:47 UTC #11 lore raw

In reply to Adrien Grassein

Quoted 11 lines · Adrien Grassein

Adrien Grassein (10):
arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip
arm64: dts: imx8mm-nitrogen-r2: rework USDHC1
arm64: dts: imx8mm-nitrogen-r2: add USB support
arm64: dts: imx8mm-nitrogen-r2: add espi2 support
arm64: dts: imx8mm-nitrogen-r2: add UARTs
arm64: dts: imx8mm-nitrogen-r2: rework UART 2
arm64: dts: imx8mm-nitrogen-r2: add PWMs
arm64: dts: imx8mm-nitrogen-r2: add FlexSPI
arm64: dts: imx8mm-nitrogen-r2: add audio
arm64: defconfig: Enable wm8960 audio driver.

Applied all, thanks.

Adrien Grassein

author

2021-03-08 11:55 UTC #12 lore raw

Quoted 14 lines · Shawn Guo

Quoted 11 lines · Adrien Grassein
Adrien Grassein (10):
arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip
arm64: dts: imx8mm-nitrogen-r2: rework USDHC1
arm64: dts: imx8mm-nitrogen-r2: add USB support
arm64: dts: imx8mm-nitrogen-r2: add espi2 support
arm64: dts: imx8mm-nitrogen-r2: add UARTs
arm64: dts: imx8mm-nitrogen-r2: rework UART 2
arm64: dts: imx8mm-nitrogen-r2: add PWMs
arm64: dts: imx8mm-nitrogen-r2: add FlexSPI
arm64: dts: imx8mm-nitrogen-r2: add audio
arm64: defconfig: Enable wm8960 audio driver.

Quoted 1 line

Applied all, thanks.

Thanks,

But I think you missed one (arm64: dts: imx8mm-nitrogen-r2: add espi2 support) that I don't see on your tree.

Thanks a lot,
Adrien

Shawn Guo

2021-03-08 12:31 UTC #13 lore raw

Quoted 15 lines · Adrien Grassein

Quoted 14 lines · Shawn Guo
Quoted 11 lines · Adrien Grassein
Adrien Grassein (10):
arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip
arm64: dts: imx8mm-nitrogen-r2: rework USDHC1
arm64: dts: imx8mm-nitrogen-r2: add USB support
arm64: dts: imx8mm-nitrogen-r2: add espi2 support
arm64: dts: imx8mm-nitrogen-r2: add UARTs
arm64: dts: imx8mm-nitrogen-r2: rework UART 2
arm64: dts: imx8mm-nitrogen-r2: add PWMs
arm64: dts: imx8mm-nitrogen-r2: add FlexSPI
arm64: dts: imx8mm-nitrogen-r2: add audio
arm64: defconfig: Enable wm8960 audio driver.

Quoted 6 lines

Quoted 1 line
Applied all, thanks.
Thanks,
But I think you missed one (arm64: dts: imx8mm-nitrogen-r2: add espi2 support) that I don't see on your tree.

Hmm, looks like it did not get posted.

https://lore.kernel.org/linux-arm-kernel/[email protected]/

Shawn

Adrien Grassein

author

2021-03-08 12:33 UTC #14 lore raw

Quoted 19 lines · Shawn Guo

Quoted 17 lines · Adrien Grassein
Quoted 15 lines · Shawn Guo
Quoted 11 lines · Adrien Grassein
Adrien Grassein (10):
arm64: dts: imx8mm-nitrogen-r2: add wifi/bt chip
arm64: dts: imx8mm-nitrogen-r2: rework USDHC1
arm64: dts: imx8mm-nitrogen-r2: add USB support
arm64: dts: imx8mm-nitrogen-r2: add espi2 support
arm64: dts: imx8mm-nitrogen-r2: add UARTs
arm64: dts: imx8mm-nitrogen-r2: rework UART 2
arm64: dts: imx8mm-nitrogen-r2: add PWMs
arm64: dts: imx8mm-nitrogen-r2: add FlexSPI
arm64: dts: imx8mm-nitrogen-r2: add audio
arm64: defconfig: Enable wm8960 audio driver.
Applied all, thanks.

Quoted 9 lines

Quoted 4 lines
Thanks,
But I think you missed one (arm64: dts: imx8mm-nitrogen-r2: add espi2 support) that I don't see on your tree.
Hmm, looks like it did not get posted.
https://lore.kernel.org/linux-arm-kernel/[email protected]/

Oh sorry, my bad.
I will repost this patch alone.

Quoted 1 line

Shawn

Thanks,
Adrien