Skip to contentSkip to conversation

mtd: rawnand: qcom: avoid writing to obsolete register

PATCH Superseded Md Sadre Alam 2 participants 3 messages Jun 7, 2021 – Jun 8, 2021

Subsystems (3)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

PATCH v3 1/1 mtd: rawnand: qcom: avoid writing to obsolete register

QPIC_EBI2_ECC_BUF_CFG register got obsolete from QPIC V2.0 onwards. Avoid writing this register if QPIC version is V2.0 or newer.

Also fixed nandc undeclared issue reported by,

---
[V3]
* Fixed nandc undeclared issue.

 drivers/mtd/nand/raw/qcom_nandc.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/mtd/nand/raw/qcom_nandc.c +12 -6
index a64fb6c..ee5985d 100644
@@ -734,6 +734,7 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read, i
 {
 	struct nand_chip *chip = &host->chip;
 	u32 cmd, cfg0, cfg1, ecc_bch_cfg;
+	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
 
 	if (read) {
 		if (host->use_ecc)
@@ -762,7 +763,8 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read, i
 	nandc_set_reg(chip, NAND_DEV0_CFG0, cfg0);
 	nandc_set_reg(chip, NAND_DEV0_CFG1, cfg1);
 	nandc_set_reg(chip, NAND_DEV0_ECC_CFG, ecc_bch_cfg);
-	nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
+	if (!nandc->props->qpic_v2)
+		nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
 	nandc_set_reg(chip, NAND_FLASH_STATUS, host->clrflashstatus);
 	nandc_set_reg(chip, NAND_READ_STATUS, host->clrreadstatus);
 	nandc_set_reg(chip, NAND_EXEC_CMD, 1);
@@ -1133,7 +1135,8 @@ static void config_nand_page_read(struct nand_chip *chip)
 
 	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
 	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
-	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
+	if (!nandc->props->qpic_v2)
+		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
 	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1, 0);
 	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1,
 		      NAND_ERASED_CW_SET | NAND_BAM_NEXT_SGL);
@@ -1191,8 +1194,9 @@ static void config_nand_page_write(struct nand_chip *chip)
 
 	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
 	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
-	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
-		      NAND_BAM_NEXT_SGL);
+	if (!nandc->props->qpic_v2)
+		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
+			      NAND_BAM_NEXT_SGL);
 }
 
 /*
@@ -1248,7 +1252,8 @@ static int nandc_param(struct qcom_nand_host *host)
 					| 2 << WR_RD_BSY_GAP
 					| 0 << WIDE_FLASH
 					| 1 << DEV0_CFG1_ECC_DISABLE);
-	nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, 1 << ECC_CFG_ECC_DISABLE);
+	if (!nandc->props->qpic_v2)
+		nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, 1 << ECC_CFG_ECC_DISABLE);
 
 	/* configure CMD1 and VLD for ONFI param probing in QPIC v1 */
 	if (!nandc->props->qpic_v2) {
@@ -2689,7 +2694,8 @@ static int qcom_nand_attach_chip(struct nand_chip *chip)
 				| ecc_mode << ECC_MODE
 				| host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_BCH;
 
-	host->ecc_buf_cfg = 0x203 << NUM_STEPS;
+	if (!nandc->props->qpic_v2)
+		host->ecc_buf_cfg = 0x203 << NUM_STEPS;
 
 	host->clrflashstatus = FS_READY_BSY_N;
 	host->clrreadstatus = 0xc0;
Signature · 1 line
2.7.4
maintainer
#1 lore raw

Hello,

Md Sadre Alam <[email protected]> wrote on Mon, 7 Jun 2021 15:13:37 +0530:

Quoted 6 lines

QPIC_EBI2_ECC_BUF_CFG register got obsolete from QPIC V2.0 onwards. Avoid writing this register if QPIC version is V2.0 or newer.

Also fixed nandc undeclared issue reported by,

This tag should only be added when you fix something that is already in mainline. The Reported-by here points to v2, which makes no sense. Please drop it.

Quoted 62 lines

---
[V3]
* Fixed nandc undeclared issue.

 drivers/mtd/nand/raw/qcom_nandc.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/mtd/nand/raw/qcom_nandc.c +10 -5
index a64fb6c..ee5985d 100644
@@ -734,6 +734,7 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read, i
 {
 	struct nand_chip *chip = &host->chip;
 	u32 cmd, cfg0, cfg1, ecc_bch_cfg;
+	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
 
 	if (read) {
 		if (host->use_ecc)
@@ -762,7 +763,8 @@ static void update_rw_regs(struct qcom_nand_host *host, int num_cw, bool read, i
 	nandc_set_reg(chip, NAND_DEV0_CFG0, cfg0);
 	nandc_set_reg(chip, NAND_DEV0_CFG1, cfg1);
 	nandc_set_reg(chip, NAND_DEV0_ECC_CFG, ecc_bch_cfg);
-	nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
+	if (!nandc->props->qpic_v2)
+		nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
 	nandc_set_reg(chip, NAND_FLASH_STATUS, host->clrflashstatus);
 	nandc_set_reg(chip, NAND_READ_STATUS, host->clrreadstatus);
 	nandc_set_reg(chip, NAND_EXEC_CMD, 1);
@@ -1133,7 +1135,8 @@ static void config_nand_page_read(struct nand_chip *chip)
 
 	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
 	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
-	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
+	if (!nandc->props->qpic_v2)
+		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
 	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1, 0);
 	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1,
 		      NAND_ERASED_CW_SET | NAND_BAM_NEXT_SGL);
@@ -1191,8 +1194,9 @@ static void config_nand_page_write(struct nand_chip *chip)
 
 	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
 	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
-	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
-		      NAND_BAM_NEXT_SGL);
+	if (!nandc->props->qpic_v2)
+		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
+			      NAND_BAM_NEXT_SGL);
 }
 
 /*
@@ -1248,7 +1252,8 @@ static int nandc_param(struct qcom_nand_host *host)
 					| 2 << WR_RD_BSY_GAP
 					| 0 << WIDE_FLASH
 					| 1 << DEV0_CFG1_ECC_DISABLE);
-	nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, 1 << ECC_CFG_ECC_DISABLE);
+	if (!nandc->props->qpic_v2)
+		nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, 1 << ECC_CFG_ECC_DISABLE);
 
 	/* configure CMD1 and VLD for ONFI param probing in QPIC v1 */
 	if (!nandc->props->qpic_v2) {

drivers/mtd/nand/raw/qcom_nandc.c static int qcom_nand_attach_chip(struct nand_chip *chip) · line 2701

Quoted 9 lines
drivers/mtd/nand/raw/qcom_nandc.c +2 -1
@@ -2689,7 +2694,8 @@ static int qcom_nand_attach_chip(struct nand_chip *chip)
 				| ecc_mode << ECC_MODE
 				| host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_BCH;
 
-	host->ecc_buf_cfg = 0x203 << NUM_STEPS;
+	if (!nandc->props->qpic_v2)
+		host->ecc_buf_cfg = 0x203 << NUM_STEPS;
 
 	host->clrflashstatus = FS_READY_BSY_N;
 	host->clrreadstatus = 0xc0;

Thanks,
Miquèl

#2 lore raw
Quoted 8 lines · Miquel Raynal

Hello,

Md Sadre Alam <[email protected]> wrote on Mon, 7 Jun 2021 15:13:37 +0530:

Quoted 3 lines

QPIC_EBI2_ECC_BUF_CFG register got obsolete from QPIC V2.0 onwards. Avoid writing this register if QPIC version is V2.0 or newer.

Quoted 7 lines
Quoted 3 lines

Also fixed nandc undeclared issue reported by,

This tag should only be added when you fix something that is already in mainline. The Reported-by here points to v2, which makes no sense. Please drop it.

updated this V4 patch.

Quoted 84 lines
Quoted 79 lines

---
[V3]
* Fixed nandc undeclared issue.

 drivers/mtd/nand/raw/qcom_nandc.c | 18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)
drivers/mtd/nand/raw/qcom_nandc.c +1 -0
index a64fb6c..ee5985d 100644
@@ -734,6 +734,7 @@ static void update_rw_regs(struct qcom_nand_host 
 *host, int num_cw, bool read, i
 {
 	struct nand_chip *chip = &host->chip;
 	u32 cmd, cfg0, cfg1, ecc_bch_cfg;
+	struct qcom_nand_controller *nandc = get_qcom_nand_controller(chip);
 
 	if (read) {
drivers/mtd/nand/raw/qcom_nandc.c +2 -1
 		if (host->use_ecc)
@@ -762,7 +763,8 @@ static void update_rw_regs(struct qcom_nand_host 
 *host, int num_cw, bool read, i
 	nandc_set_reg(chip, NAND_DEV0_CFG0, cfg0);
 	nandc_set_reg(chip, NAND_DEV0_CFG1, cfg1);
 	nandc_set_reg(chip, NAND_DEV0_ECC_CFG, ecc_bch_cfg);
-	nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
+	if (!nandc->props->qpic_v2)
+		nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, host->ecc_buf_cfg);
 	nandc_set_reg(chip, NAND_FLASH_STATUS, host->clrflashstatus);
 	nandc_set_reg(chip, NAND_READ_STATUS, host->clrreadstatus);
drivers/mtd/nand/raw/qcom_nandc.c +2 -1
 	nandc_set_reg(chip, NAND_EXEC_CMD, 1);
@@ -1133,7 +1135,8 @@ static void config_nand_page_read(struct 
 nand_chip *chip)
 
 	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
 	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
-	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
+	if (!nandc->props->qpic_v2)
+		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
 	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1, 0);
 	write_reg_dma(nandc, NAND_ERASED_CW_DETECT_CFG, 1,
drivers/mtd/nand/raw/qcom_nandc.c +3 -2
 		      NAND_ERASED_CW_SET | NAND_BAM_NEXT_SGL);
@@ -1191,8 +1194,9 @@ static void config_nand_page_write(struct 
 nand_chip *chip)
 
 	write_reg_dma(nandc, NAND_ADDR0, 2, 0);
 	write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
-	write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
-		      NAND_BAM_NEXT_SGL);
+	if (!nandc->props->qpic_v2)
+		write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
+			      NAND_BAM_NEXT_SGL);
 }
 

/*

drivers/mtd/nand/raw/qcom_nandc.c +2 -1
@@ -1248,7 +1252,8 @@ static int nandc_param(struct qcom_nand_host 
 *host)
 					| 2 << WR_RD_BSY_GAP
 					| 0 << WIDE_FLASH
 					| 1 << DEV0_CFG1_ECC_DISABLE);
-	nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, 1 << 
 ECC_CFG_ECC_DISABLE);
+	if (!nandc->props->qpic_v2)
+		nandc_set_reg(chip, NAND_EBI2_ECC_BUF_CFG, 1 << 
 ECC_CFG_ECC_DISABLE);
drivers/mtd/nand/raw/qcom_nandc.c +2 -1
 	/* configure CMD1 and VLD for ONFI param probing in QPIC v1 */
 	if (!nandc->props->qpic_v2) {
@@ -2689,7 +2694,8 @@ static int qcom_nand_attach_chip(struct 
 nand_chip *chip)
 				| ecc_mode << ECC_MODE
 				| host->ecc_bytes_hw << ECC_PARITY_SIZE_BYTES_BCH;
 
-	host->ecc_buf_cfg = 0x203 << NUM_STEPS;
+	if (!nandc->props->qpic_v2)
+		host->ecc_buf_cfg = 0x203 << NUM_STEPS;
 
 	host->clrflashstatus = FS_READY_BSY_N;
Quoted 1 line

host->clrreadstatus = 0xc0;

Thanks,
Miquèl