Skip to contentSkip to conversation

Add Rockchip SFC(serial flash controller) support

PATCH Superseded Jon Lin 4 participants 20 messages Jun 8, 2021 – Jun 9, 2021

Subsystems (5)

v6 of 13 Superseded Latest is v13 →

lore
Share & tools
lore

Jon Lin

author
#0 lore raw

v6 cover Add Rockchip SFC(serial flash controller) support

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip reached out to me to let me know they are working on this patch for upstream, I am submitting this v4 for the community to see however I expect Jon Lin ([email protected]) will submit new patches soon and these are the ones we should pursue for mainlining. Jon's patch series should include support for more hardware than this series.
- Clean up documentation more and ensure it is correct per make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to rockchip,rk3036-sfc. A quick glance at the datasheets suggests this driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and RV1108 SoCs, and possibly more. However, I am currently only able to test this on a PX30 (an RK3326). The technical reference manuals appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the event that the SPI chip supports 4x mode but only has 2 pins wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

Chris Morgan (8):
dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash
controller
spi: rockchip-sfc: add rockchip serial flash controller
arm64: dts: rockchip: Add SFC to PX30
clk: rockchip: Add support for hclk_sfc on rk3036
arm: dts: rockchip: Add SFC to RK3036
arm: dts: rockchip: Add SFC to RV1108
arm64: dts: rockchip: Add SFC to RK3308
arm64: dts: rockchip: Enable SFC for Odroid Go Advance

 .../devicetree/bindings/spi/rockchip-sfc.yaml |  87 +++
 arch/arm/boot/dts/rk3036.dtsi                 |  42 ++
 arch/arm/boot/dts/rv1108.dtsi                 |  37 +
 arch/arm64/boot/dts/rockchip/px30.dtsi        |  38 +
 arch/arm64/boot/dts/rockchip/rk3308.dtsi      |  37 +
 .../boot/dts/rockchip/rk3326-odroid-go2.dts   |  16 +
 drivers/clk/rockchip/clk-rk3036.c             |   2 +-
 drivers/spi/Kconfig                           |   9 +
 drivers/spi/Makefile                          |   1 +
 drivers/spi/spi-rockchip-sfc.c                | 660 ++++++++++++++++++
 include/dt-bindings/clock/rk3036-cru.h        |   1 +
 11 files changed, 929 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
 create mode 100644 drivers/spi/spi-rockchip-sfc.c
Signature · 9 lines
2.17.1




_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip
author
#1 lore raw

PATCH v6 1/8 dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller

From: Chris Morgan <[email protected]>

Add bindings for the Rockchip serial flash controller. New device specific parameter of rockchip,sfc-no-dma included in documentation.

---

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip reached out to me to let me know they are working on this patch for upstream, I am submitting this v4 for the community to see however I expect Jon Lin ([email protected]) will submit new patches soon and these are the ones we should pursue for mainlining. Jon's patch series should include support for more hardware than this series.
- Clean up documentation more and ensure it is correct per make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to rockchip,rk3036-sfc. A quick glance at the datasheets suggests this driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and RV1108 SoCs, and possibly more. However, I am currently only able to test this on a PX30 (an RK3326). The technical reference manuals appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the event that the SPI chip supports 4x mode but only has 2 pins wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

 .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++
 1 file changed, 87 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +87 -0
new file mode 100644
index 000000000000..160449713f97
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip Serial Flash Controller (SFC)
+
+maintainers:
+  - Heiko Stuebner <[email protected]>
+  - Chris Morgan <[email protected]>
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - const: rockchip,rk3036-sfc
+      - items:
+          - enum:
+              - rockchip,px30-sfc
+              - rockchip,rk3308-sfc
+              - rockchip,rv1108-sfc
+          - const: rockchip,rk3036-sfc
+      - const: rockchip,rv1126-sfc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: hclk_sfc
+      - const: clk_sfc
+
+  power-domains:
+    maxItems: 1
+
+  rockchip,sfc-no-dma:
+    description: Disable DMA and utilize FIFO mode only
+    type: boolean
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/px30-power.h>
+
+    sfc: spi@ff3a0000 {
+        compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc";
+        reg = <0xff3a0000 0x4000>;
+        interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+        clock-names = "clk_sfc", "hclk_sfc";
+        pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;
+        pinctrl-names = "default";
+        power-domains = <&power PX30_PD_MMC_NAND>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {
+            compatible = "jedec,spi-nor";
+            reg = <0>;
+            spi-max-frequency = <108000000>;
+            spi-rx-bus-width = <2>;
+            spi-tx-bus-width = <2>;
+        };
+    };
+
+...
Signature · 1 line
2.17.1
#2 lore raw

Re: [PATCH v6 1/8] dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller

Hi Jon,

A look at the build log shows this error:

https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:
spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected
From schema:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:
spi@ff3a0000: clock-names:1: 'clk_sfc' was expected
From schema:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Check document with:

make ARCH=arm dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Remove any errors before submitting.

===

Johan

Quoted 90 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add bindings for the Rockchip serial flash controller. New device specific parameter of rockchip,sfc-no-dma included in documentation.

---

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip reached out to me to let me know they are working on this patch for upstream, I am submitting this v4 for the community to see however I expect Jon Lin ([email protected]) will submit new patches soon and these are the ones we should pursue for mainlining. Jon's patch series should include support for more hardware than this series.
- Clean up documentation more and ensure it is correct per make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to rockchip,rk3036-sfc. A quick glance at the datasheets suggests this driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and RV1108 SoCs, and possibly more. However, I am currently only able to test this on a PX30 (an RK3326). The technical reference manuals appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the event that the SPI chip supports 4x mode but only has 2 pins wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

 .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++
 1 file changed, 87 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +2 -0
new file mode 100644
index 000000000000..160449713f97
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 11

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +9 -0
+---
+$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip Serial Flash Controller (SFC)
+
+maintainers:
+  - Heiko Stuebner <[email protected]>
 
+  - Chris Morgan <[email protected]>

In the driver spi-rockchip-sfc.c is used:
Chris Morgan <[email protected]>
Maybe use a consistent email address?
Also Hotmail does strange things to message-ID's and links/content inside patches.

Quoted 6 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +6 -0
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:
+  compatible:

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 26

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +9 -0
+    oneOf:
 
+      - const: rockchip,rk3036-sfc
+      - items:
+          - enum:
+              - rockchip,px30-sfc
+              - rockchip,rk3308-sfc
+              - rockchip,rv1108-sfc
+          - const: rockchip,rk3036-sfc
+      - const: rockchip,rv1126-sfc

A look at the driver shows this:

+static const struct of_device_id rockchip_sfc_dt_ids[] = {

+ { .compatible = "rockchip,px30-sfc"},

remove

+ { .compatible = "rockchip,rk3036-sfc"},

+ { .compatible = "rockchip,rk3308-sfc"},
+ { .compatible = "rockchip,rv1126-sfc"},

remove

+ { /* sentinel */ }
+};

When no '.data = &my_sfc_data' exist then there's no need for additional compatible strings in the driver.
===
example for I2S:

	{ .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins },

===
Compatibility strings are supposed to be SoC orientated. With rockchip_sfc_get_version() all we need is one fall back string for now I think. Is rk3568 identical. Please advise.

- const: rockchip,rk3036-sfc
- items:
- enum:
- rockchip,px30-sfc
- rockchip,rk3308-sfc
- rockchip,rk3368-sfc
- rockchip,rk3568-sfc
- rockchip,rv1108-sfc
- rockchip,rv1126-sfc
- const: rockchip,rk3036-sfc

===

The rk3368 TRM also describes a SFC controller.
For the mainline DT completeness is it possible to add a rk3368 SFC node as well? ;)

Quoted 36 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +36 -0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: hclk_sfc
+      - const: clk_sfc
+
+  power-domains:
+    maxItems: 1
+
+  rockchip,sfc-no-dma:
+    description: Disable DMA and utilize FIFO mode only
+    type: boolean
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/px30-cru.h>

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 71

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +9 -0
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/px30-power.h>
+
+    sfc: spi@ff3a0000 {
+        compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc";
+        reg = <0xff3a0000 0x4000>;
+        interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
 
+        clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+        clock-names = "clk_sfc", "hclk_sfc";

The clocks in the examples and dtsi files must have the same sort order.

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 78

Quoted 8 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +7 -0
+        pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;
+        pinctrl-names = "default";
+        power-domains = <&power PX30_PD_MMC_NAND>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
 
+        flash@0 {

From spi-controller.yaml:

patternProperties:
"^.*@[0-9a-f]+$":
type: object

properties:
compatible:
description:
Compatible of the SPI device.

reg:
minimum: 0

maximum: 256

description:
Chip select used by the device.

This allows 257 sub nodes.
Support up to 4 chip select in the driver.
#define SFC_MAX_CHIPSELECT_NUM 4

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +9 -0
+            compatible = "jedec,spi-nor";
+            reg = <0>;
+            spi-max-frequency = <108000000>;
+            spi-rx-bus-width = <2>;
+            spi-tx-bus-width = <2>;
+        };
+    };
+
+...
author
#3 lore raw

Re: [PATCH v6 1/8] dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller

Quoted 268 lines · Johan Jonker

Hi Jon,

A look at the build log shows this error:

https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:
spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected
From schema:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:
spi@ff3a0000: clock-names:1: 'clk_sfc' was expected
From schema:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Check document with:

make ARCH=arm dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Remove any errors before submitting.

===

Johan

Quoted 89 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add bindings for the Rockchip serial flash controller. New device specific parameter of rockchip,sfc-no-dma included in documentation.

---

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip reached out to me to let me know they are working on this patch for upstream, I am submitting this v4 for the community to see however I expect Jon Lin ([email protected]) will submit new patches soon and these are the ones we should pursue for mainlining. Jon's patch series should include support for more hardware than this series.
- Clean up documentation more and ensure it is correct per make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to rockchip,rk3036-sfc. A quick glance at the datasheets suggests this driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and RV1108 SoCs, and possibly more. However, I am currently only able to test this on a PX30 (an RK3326). The technical reference manuals appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the event that the SPI chip supports 4x mode but only has 2 pins wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

  .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++
  1 file changed, 87 insertions(+)

create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +1 -0
new file mode 100644
index 000000000000..160449713f97
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 11

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +10 -0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip Serial Flash Controller (SFC)
+
+maintainers:
+  - Heiko Stuebner <[email protected]>
+  - Chris Morgan <[email protected]>

In the driver spi-rockchip-sfc.c is used:
Chris Morgan <[email protected]>
Maybe use a consistent email address?
Also Hotmail does strange things to message-ID's and links/content inside patches.

Quoted 5 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +5 -0
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 26

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +10 -0
+  compatible:
+    oneOf:
+      - const: rockchip,rk3036-sfc
+      - items:
+          - enum:
+              - rockchip,px30-sfc
+              - rockchip,rk3308-sfc
+              - rockchip,rv1108-sfc
+          - const: rockchip,rk3036-sfc
+      - const: rockchip,rv1126-sfc

A look at the driver shows this:

(quoted diff) +2 -0
+static const struct of_device_id rockchip_sfc_dt_ids[] = {
 
+	{ .compatible = "rockchip,px30-sfc"},

remove

(quoted diff) +3 -0
+	{ .compatible = "rockchip,rk3036-sfc"},
 
+	{ .compatible = "rockchip,rk3308-sfc"},
+	{ .compatible = "rockchip,rv1126-sfc"},

remove

(quoted diff) +2 -0
+	{ /* sentinel */ }
+};

When no '.data = &my_sfc_data' exist then there's no need for additional compatible strings in the driver.
===
example for I2S:

	{ .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins },

===
Compatibility strings are supposed to be SoC orientated. With rockchip_sfc_get_version() all we need is one fall back string for now I think. Is rk3568 identical. Please advise.

- const: rockchip,rk3036-sfc
- items:
- enum:
- rockchip,px30-sfc
- rockchip,rk3308-sfc
- rockchip,rk3368-sfc
- rockchip,rk3568-sfc
- rockchip,rv1108-sfc
- rockchip,rv1126-sfc
- const: rockchip,rk3036-sfc

===

The rk3368 TRM also describes a SFC controller.
For the mainline DT completeness is it possible to add a rk3368 SFC node as well? ;)

Quoted 35 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +35 -0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: hclk_sfc
+      - const: clk_sfc
+
+  power-domains:
+    maxItems: 1
+
+  rockchip,sfc-no-dma:
+    description: Disable DMA and utilize FIFO mode only
+    type: boolean
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 71

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +10 -0
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/px30-power.h>
+
+    sfc: spi@ff3a0000 {
+        compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc";
+        reg = <0xff3a0000 0x4000>;
+        interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+        clock-names = "clk_sfc", "hclk_sfc";

The clocks in the examples and dtsi files must have the same sort order.

Quoted 8 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +7 -0
+        pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;
+        pinctrl-names = "default";
+        power-domains = <&power PX30_PD_MMC_NAND>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {

From spi-controller.yaml:

patternProperties:
"^.*@[0-9a-f]+$":
type: object

properties:
compatible:
description:
Compatible of the SPI device.

reg:
minimum: 0

Quoted 8 lines

maximum: 256

description:
Chip select used by the device.

This allows 257 sub nodes.
Support up to 4 chip select in the driver.
#define SFC_MAX_CHIPSELECT_NUM 4

RK SFC design is up to 4 CS.

Sorry, I don't see any specific improvement in this comment, can you explain it in detail.

Quoted 13 lines
Quoted 11 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +9 -0
+            compatible = "jedec,spi-nor";
+            reg = <0>;
+            spi-max-frequency = <108000000>;
+            spi-rx-bus-width = <2>;
+            spi-tx-bus-width = <2>;
+        };
+    };
+
+...
#4 lore raw

Re: [PATCH v6 1/8] dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller

Quoted 282 lines · Jon Lin
Quoted 280 lines · Johan Jonker

Hi Jon,

A look at the build log shows this error:

https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:

spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected
    From schema:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml:

spi@ff3a0000: clock-names:1: 'clk_sfc' was expected
    From schema:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Check document with:

make ARCH=arm dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Remove any errors before submitting.

===

Johan

Quoted 91 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add bindings for the Rockchip serial flash controller. New device specific parameter of rockchip,sfc-no-dma included in documentation.

---

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip reached out to me to let me know they are working on this patch for upstream, I am submitting this v4 for the community to see however I expect Jon Lin ([email protected]) will submit new patches soon and these are the ones we should pursue for mainlining. Jon's patch series should include support for more hardware than this series.
- Clean up documentation more and ensure it is correct per make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to rockchip,rk3036-sfc. A quick glance at the datasheets suggests this driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and RV1108 SoCs, and possibly more. However, I am currently only able to test this on a PX30 (an RK3326). The technical reference manuals appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the event that the SPI chip supports 4x mode but only has 2 pins wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

  .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++

  1 file changed, 87 insertions(+)

  create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +1 -0
new file mode 100644
index 000000000000..160449713f97
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 11

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +10 -0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/rockchip-sfc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Rockchip Serial Flash Controller (SFC)
+
+maintainers:
+  - Heiko Stuebner <[email protected]>
+  - Chris Morgan <[email protected]>

In the driver spi-rockchip-sfc.c is used:
Chris Morgan <[email protected]>
Maybe use a consistent email address?
Also Hotmail does strange things to message-ID's and links/content inside patches.

Quoted 5 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +5 -0
+
+allOf:
+  - $ref: spi-controller.yaml#
+
+properties:

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 26

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +10 -0
+  compatible:
+    oneOf:
+      - const: rockchip,rk3036-sfc
+      - items:
+          - enum:
+              - rockchip,px30-sfc
+              - rockchip,rk3308-sfc
+              - rockchip,rv1108-sfc
+          - const: rockchip,rk3036-sfc
+      - const: rockchip,rv1126-sfc

A look at the driver shows this:

+static const struct of_device_id rockchip_sfc_dt_ids[] = {

+    { .compatible = "rockchip,px30-sfc"},

remove

+    { .compatible = "rockchip,rk3036-sfc"},

+    { .compatible = "rockchip,rk3308-sfc"},
+    { .compatible = "rockchip,rv1126-sfc"},

remove

+    { /* sentinel */ }
+};

When no '.data = &my_sfc_data' exist then there's no need for additional compatible strings in the driver.
===
example for I2S:
    { .compatible = "rockchip,rk3399-i2s", .data = &rk3399_i2s_pins },
===
Compatibility strings are supposed to be SoC orientated. With rockchip_sfc_get_version() all we need is one fall back string for now I think. Is rk3568 identical. Please advise.

       - const: rockchip,rk3036-sfc
       - items:
           - enum:
               - rockchip,px30-sfc
               - rockchip,rk3308-sfc
               - rockchip,rk3368-sfc
               - rockchip,rk3568-sfc
               - rockchip,rv1108-sfc
               - rockchip,rv1126-sfc
           - const: rockchip,rk3036-sfc

===

The rk3368 TRM also describes a SFC controller.
For the mainline DT completeness is it possible to add a rk3368 SFC node as well? ;)

Quoted 35 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +35 -0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Bus Clock
+      - description: Module Clock
+
+  clock-names:
+    items:
+      - const: hclk_sfc
+      - const: clk_sfc
+
+  power-domains:
+    maxItems: 1
+
+  rockchip,sfc-no-dma:
+    description: Disable DMA and utilize FIFO mode only
+    type: boolean
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |

Documentation/devicetree/bindings/spi/rockchip-sfc.yaml line 71

Quoted 10 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +10 -0
+    #include <dt-bindings/clock/px30-cru.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/px30-power.h>
+
+    sfc: spi@ff3a0000 {
+        compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc";
+        reg = <0xff3a0000 0x4000>;
+        interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+        clock-names = "clk_sfc", "hclk_sfc";

The clocks in the examples and dtsi files must have the same sort order.

Quoted 8 lines
Documentation/devicetree/bindings/spi/rockchip-sfc.yaml new file +7 -0
+        pinctrl-0 = <&sfc_clk &sfc_cs &sfc_bus2>;
+        pinctrl-names = "default";
+        power-domains = <&power PX30_PD_MMC_NAND>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        flash@0 {

From spi-controller.yaml:

patternProperties:
   "^.*@[0-9a-f]+$":
     type: object

     properties:
       compatible:
         description:
           Compatible of the SPI device.

       reg:
         minimum: 0

         maximum: 256

         description:
           Chip select used by the device.

Quoted 8 lines
Quoted 3 lines

This allows 257 sub nodes.
Support up to 4 chip select in the driver.
#define SFC_MAX_CHIPSELECT_NUM        4

RK SFC design is up to 4 CS.

Sorry, I don't see any specific improvement in this comment, can you explain it in detail.

In the old text documents it only described the hardware. With the new YAML format we also check new dts submissions for bogus properties. So if someone comes up with this example:

flash@88 {
compatible = "jedec,spi-nor";
reg = <0x88>;
}

This must give a out of range notification.

Also when someone tries to connect something else then flash that must be detected. The spi-controller.yaml allows any node name.

patternProperties:

    "^flash@[0-3]$":
      type: object

      properties:
        compatible:
          const: jedec,spi-nor

        reg:
          minimum: 0
          maximum: 3

===

Example from rockchip,nand-controller.yaml:

patternProperties:
"^nand@[0-7]$":
type: object
properties:
reg:
minimum: 0
maximum: 7

===

Quoted 15 lines
Quoted 13 lines
Quoted 11 lines

+            compatible = "jedec,spi-nor";
+            reg = <0>;
+            spi-max-frequency = <108000000>;
+            spi-rx-bus-width = <2>;
+            spi-tx-bus-width = <2>;
+        };
+    };
+
+...

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip

maintainer
#5 lore raw

Re: [PATCH v6 1/8] dt-bindings: rockchip-sfc: Bindings for Rockchip serial flash controller

In reply to Jon Lin
Quoted 78 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add bindings for the Rockchip serial flash controller. New device specific parameter of rockchip,sfc-no-dma included in documentation.

---

Changes in v6:
- Add support in device trees for rv1126(Declared in series 5 but not submitted)
- Change to use "clk_sfc" "hclk_sfc" as clock lable, since it does not affect interpretation and has been widely used
- Support sfc tx_dual, tx_quad(Declared in series 5 but not submitted)
- Simplify the code, such as remove "rockchip_sfc_register_all"(Declared in series 5 but not submitted)
- Support SFC ver4 ver5(Declared in series 5 but not submitted)
- Add author Chris Morgan and Jon Lin to spi-rockchip-sfc.c
- Change to use devm_spi_alloc_master and spi_unregister_master

Changes in v5:
- Add support in device trees for rv1126
- Support sfc tx_dual, tx_quad
- Simplify the code, such as remove "rockchip_sfc_register_all"
- Support SFC ver4 ver5

Changes in v4:
- Changing patch back to an "RFC". An engineer from Rockchip reached out to me to let me know they are working on this patch for upstream, I am submitting this v4 for the community to see however I expect Jon Lin ([email protected]) will submit new patches soon and these are the ones we should pursue for mainlining. Jon's patch series should include support for more hardware than this series.
- Clean up documentation more and ensure it is correct per make dt_binding_check.
- Add support in device trees for rk3036, rk3308, and rv1108.
- Add ahb clock (hclk_sfc) support for rk3036.
- Change rockchip_sfc_wait_fifo_ready() to use a switch statement.
- Change IRQ code to only mark IRQ as handled if it handles the specific IRQ (DMA transfer finish) it is supposed to handle.

Changes in v3:
- Changed the name of the clocks to sfc/ahb (from clk-sfc/clk-hsfc).
- Changed the compatible string from rockchip,sfc to rockchip,rk3036-sfc. A quick glance at the datasheets suggests this driver should work for the PX30, RK180x, RK3036, RK312x, RK3308 and RV1108 SoCs, and possibly more. However, I am currently only able to test this on a PX30 (an RK3326). The technical reference manuals appear to list the same registers for each device.
- Corrected devicetree documentation for formatting and to note these changes.
- Replaced the maintainer with Heiko Stuebner and myself, as we will take ownership of this going forward.
- Noted that the device (per the reference manual) supports 4 CS, but I am only able to test a single CS (CS 0).
- Reordered patches to comply with upstream rules.

Changes in v2:
- Reimplemented driver using spi-mem subsystem.
- Removed power management code as I couldn't get it working properly.
- Added device tree bindings for Odroid Go Advance.

Changes in v1:
hanges made in this new series versus the v8 of the old series:
- Added function to read spi-rx-bus-width from device tree, in the event that the SPI chip supports 4x mode but only has 2 pins wired (such as the Odroid Go Advance).
- Changed device tree documentation from txt to yaml format.
- Made "reset" message a dev_dbg from a dev_info.
- Changed read and write fifo functions to remove redundant checks.
- Changed the write and read from relaxed to non-relaxed when starting the DMA transfer or reading the DMA IRQ.
- Changed from dma_coerce_mask_and_coherent to just dma_set_mask_and_coherent.
- Changed name of get_if_type to rockchip_sfc_get_if_type.

Quoted 4 lines
 .../devicetree/bindings/spi/rockchip-sfc.yaml | 87 +++++++++++++++++++
 1 file changed, 87 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/spi/rockchip-sfc.yaml

My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13):

yamllint warnings/errors:

dtschema/dtc warnings/errors:
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: spi@ff3a0000: clock-names:0: 'hclk_sfc' was expected
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
/builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.example.dt.yaml: spi@ff3a0000: clock-names:1: 'clk_sfc' was expected
From schema: /builds/robherring/linux-dt-review/Documentation/devicetree/bindings/spi/rockchip-sfc.yaml
\ndoc reference errors (make refcheckdocs):

See https://patchwork.ozlabs.org/patch/1489062

This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1.

If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date:

pip3 install dtschema --upgrade

Please check and re-submit.

author
#6 lore raw

PATCH v6 2/8 spi: rockchip-sfc: add rockchip serial flash controller

In reply to Jon Lin

From: Chris Morgan <[email protected]>

Add the rockchip serial flash controller (SFC) driver.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 drivers/spi/Kconfig            |   9 +
 drivers/spi/Makefile           |   1 +
 drivers/spi/spi-rockchip-sfc.c | 660 +++++++++++++++++++++++++++++++++
 3 files changed, 670 insertions(+)
 create mode 100644 drivers/spi/spi-rockchip-sfc.c
drivers/spi/Kconfig +9 -0
index e71a4c514f7b..d89e5f3c9107 100644
@@ -658,6 +658,15 @@ config SPI_ROCKCHIP
 	  The main usecase of this controller is to use spi flash as boot
 	  device.
 
+config SPI_ROCKCHIP_SFC
+	tristate "Rockchip Serial Flash Controller (SFC)"
+	depends on ARCH_ROCKCHIP || COMPILE_TEST
+	depends on HAS_IOMEM && HAS_DMA
+	help
+	  This enables support for Rockchip serial flash controller. This
+	  is a specialized controller used to access SPI flash on some
+	  Rockchip SOCs.
+
 config SPI_RB4XX
 	tristate "Mikrotik RB4XX SPI master"
 	depends on SPI_MASTER && ATH79
drivers/spi/Makefile +1 -0
index 13e54c45e9df..699db95c8441 100644
@@ -95,6 +95,7 @@ obj-$(CONFIG_SPI_QCOM_GENI)		+= spi-geni-qcom.o
 obj-$(CONFIG_SPI_QCOM_QSPI)		+= spi-qcom-qspi.o
 obj-$(CONFIG_SPI_QUP)			+= spi-qup.o
 obj-$(CONFIG_SPI_ROCKCHIP)		+= spi-rockchip.o
+obj-$(CONFIG_SPI_ROCKCHIP_SFC)		+= spi-rockchip-sfc.o
 obj-$(CONFIG_SPI_RB4XX)			+= spi-rb4xx.o
 obj-$(CONFIG_MACH_REALTEK_RTL)		+= spi-realtek-rtl.o
 obj-$(CONFIG_SPI_RPCIF)			+= spi-rpc-if.o
drivers/spi/spi-rockchip-sfc.c new file +660 -0

660 lines not on this page · raw message

Signature · 1 line
2.17.1
#7 lore raw

Re: [PATCH v6 2/8] spi: rockchip-sfc: add rockchip serial flash controller

Quoted 6 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add the rockchip serial flash controller (SFC) driver.

I think I hit "reply" earlier when I meant to hit "reply-all". Whoops.

I wanted to say that for now this driver is not working for me on the v3 hardware. There appears to be something wrong with alternating between page programs and erase. I can consistently reproduce this by writing a 4MB image of random data to my SPI flash chip at offset c00000 using dd to mtdblock0. I've dumped the contents of what is written to the controller and it appears at some point it goes from doing a page program (02) to a dual io read (bb) to a sector erase (20), then it repeatedly reads the status register (05) and I assume the register never changes. As a result it just keeps looping over the status register then eventually times out. I'm still debugging to try and figure out exactly what is going on though.

I also noticed that reading does not work consistently using dd from the mtd0 device, however I have a proposed fix for that which I list below at the appropriate section.

Quoted 333 lines

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 drivers/spi/Kconfig            |   9 +
 drivers/spi/Makefile           |   1 +
 drivers/spi/spi-rockchip-sfc.c | 660 +++++++++++++++++++++++++++++++++
 3 files changed, 670 insertions(+)
 create mode 100644 drivers/spi/spi-rockchip-sfc.c
drivers/spi/Kconfig +9 -0
index e71a4c514f7b..d89e5f3c9107 100644
@@ -658,6 +658,15 @@ config SPI_ROCKCHIP
 	  The main usecase of this controller is to use spi flash as boot
 	  device.
 
+config SPI_ROCKCHIP_SFC
+	tristate "Rockchip Serial Flash Controller (SFC)"
+	depends on ARCH_ROCKCHIP || COMPILE_TEST
+	depends on HAS_IOMEM && HAS_DMA
+	help
+	  This enables support for Rockchip serial flash controller. This
+	  is a specialized controller used to access SPI flash on some
+	  Rockchip SOCs.
+
 config SPI_RB4XX
 	tristate "Mikrotik RB4XX SPI master"
 	depends on SPI_MASTER && ATH79
drivers/spi/Makefile +1 -0
index 13e54c45e9df..699db95c8441 100644
@@ -95,6 +95,7 @@ obj-$(CONFIG_SPI_QCOM_GENI)		+= spi-geni-qcom.o
 obj-$(CONFIG_SPI_QCOM_QSPI)		+= spi-qcom-qspi.o
 obj-$(CONFIG_SPI_QUP)			+= spi-qup.o
 obj-$(CONFIG_SPI_ROCKCHIP)		+= spi-rockchip.o
+obj-$(CONFIG_SPI_ROCKCHIP_SFC)		+= spi-rockchip-sfc.o
 obj-$(CONFIG_SPI_RB4XX)			+= spi-rb4xx.o
 obj-$(CONFIG_MACH_REALTEK_RTL)		+= spi-realtek-rtl.o
 obj-$(CONFIG_SPI_RPCIF)			+= spi-rpc-if.o
drivers/spi/spi-rockchip-sfc.c new file +280 -0
new file mode 100644
index 000000000000..ec25ad278096
@@ -0,0 +1,660 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Rockchip Serial Flash Controller Driver
+ *
+ * Copyright (c) 2017-2021, Rockchip Inc.
+ * Author: Shawn Lin <[email protected]>
+ *	   Chris Morgan <[email protected]>
+ *	   Jon Lin <[email protected]>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi-mem.h>
+
+/* System control */
+#define SFC_CTRL			0x0
+#define  SFC_CTRL_PHASE_SEL_NEGETIVE	BIT(1)
+#define  SFC_CTRL_CMD_BITS_SHIFT	8
+#define  SFC_CTRL_ADDR_BITS_SHIFT	10
+#define  SFC_CTRL_DATA_BITS_SHIFT	12
+
+/* Interrupt mask */
+#define SFC_IMR				0x4
+#define  SFC_IMR_RX_FULL		BIT(0)
+#define  SFC_IMR_RX_UFLOW		BIT(1)
+#define  SFC_IMR_TX_OFLOW		BIT(2)
+#define  SFC_IMR_TX_EMPTY		BIT(3)
+#define  SFC_IMR_TRAN_FINISH		BIT(4)
+#define  SFC_IMR_BUS_ERR		BIT(5)
+#define  SFC_IMR_NSPI_ERR		BIT(6)
+#define  SFC_IMR_DMA			BIT(7)
+
+/* Interrupt clear */
+#define SFC_ICLR			0x8
+#define  SFC_ICLR_RX_FULL		BIT(0)
+#define  SFC_ICLR_RX_UFLOW		BIT(1)
+#define  SFC_ICLR_TX_OFLOW		BIT(2)
+#define  SFC_ICLR_TX_EMPTY		BIT(3)
+#define  SFC_ICLR_TRAN_FINISH		BIT(4)
+#define  SFC_ICLR_BUS_ERR		BIT(5)
+#define  SFC_ICLR_NSPI_ERR		BIT(6)
+#define  SFC_ICLR_DMA			BIT(7)
+
+/* FIFO threshold level */
+#define SFC_FTLR			0xc
+#define  SFC_FTLR_TX_SHIFT		0
+#define  SFC_FTLR_TX_MASK		0x1f
+#define  SFC_FTLR_RX_SHIFT		8
+#define  SFC_FTLR_RX_MASK		0x1f
+
+/* Reset FSM and FIFO */
+#define SFC_RCVR			0x10
+#define  SFC_RCVR_RESET			BIT(0)
+
+/* Enhanced mode */
+#define SFC_AX				0x14
+
+/* Address Bit number */
+#define SFC_ABIT			0x18
+
+/* Interrupt status */
+#define SFC_ISR				0x1c
+#define  SFC_ISR_RX_FULL_SHIFT		BIT(0)
+#define  SFC_ISR_RX_UFLOW_SHIFT		BIT(1)
+#define  SFC_ISR_TX_OFLOW_SHIFT		BIT(2)
+#define  SFC_ISR_TX_EMPTY_SHIFT		BIT(3)
+#define  SFC_ISR_TX_FINISH_SHIFT	BIT(4)
+#define  SFC_ISR_BUS_ERR_SHIFT		BIT(5)
+#define  SFC_ISR_NSPI_ERR_SHIFT		BIT(6)
+#define  SFC_ISR_DMA_SHIFT		BIT(7)
+
+/* FIFO status */
+#define SFC_FSR				0x20
+#define  SFC_FSR_TX_IS_FULL		BIT(0)
+#define  SFC_FSR_TX_IS_EMPTY		BIT(1)
+#define  SFC_FSR_RX_IS_EMPTY		BIT(2)
+#define  SFC_FSR_RX_IS_FULL		BIT(3)
+#define  SFC_FSR_TXLV_MASK		GENMASK(12, 8)
+#define  SFC_FSR_TXLV_SHIFT		8
+#define  SFC_FSR_RXLV_MASK		GENMASK(20, 16)
+#define  SFC_FSR_RXLV_SHIFT		16
+
+/* FSM status */
+#define SFC_SR				0x24
+#define  SFC_SR_IS_IDLE			0x0
+#define  SFC_SR_IS_BUSY			0x1
+
+/* Raw interrupt status */
+#define SFC_RISR			0x28
+#define  SFC_RISR_RX_FULL		BIT(0)
+#define  SFC_RISR_RX_UNDERFLOW		BIT(1)
+#define  SFC_RISR_TX_OVERFLOW		BIT(2)
+#define  SFC_RISR_TX_EMPTY		BIT(3)
+#define  SFC_RISR_TRAN_FINISH		BIT(4)
+#define  SFC_RISR_BUS_ERR		BIT(5)
+#define  SFC_RISR_NSPI_ERR		BIT(6)
+#define  SFC_RISR_DMA			BIT(7)
+
+/* Version */
+#define SFC_VER				0x2C
+#define  SFC_VER_3			0x3
+#define  SFC_VER_4			0x4
+#define  SFC_VER_5			0x5
+
+/* Master trigger */
+#define SFC_DMA_TRIGGER			0x80
+
+/* Src or Dst addr for master */
+#define SFC_DMA_ADDR			0x84
+
+/* Length control register extension 32GB */
+#define SFC_LEN_CTRL			0x88
+#define SFC_LEN_CTRL_TRB_SEL		1
+#define SFC_LEN_EXT			0x8C
+
+/* Command */
+#define SFC_CMD				0x100
+#define  SFC_CMD_IDX_SHIFT		0
+#define  SFC_CMD_DUMMY_SHIFT		8
+#define  SFC_CMD_DIR_SHIFT		12
+#define  SFC_CMD_DIR_RD			0
+#define  SFC_CMD_DIR_WR			1
+#define  SFC_CMD_ADDR_SHIFT		14
+#define  SFC_CMD_ADDR_0BITS		0
+#define  SFC_CMD_ADDR_24BITS		1
+#define  SFC_CMD_ADDR_32BITS		2
+#define  SFC_CMD_ADDR_XBITS		3
+#define  SFC_CMD_TRAN_BYTES_SHIFT	16
+#define  SFC_CMD_CS_SHIFT		30
+
+/* Address */
+#define SFC_ADDR			0x104
+
+/* Data */
+#define SFC_DATA			0x108
+
+/* The controller and documentation reports that it supports up to 4 CS
+ * devices (0-3), however I have only been able to test a single CS (CS 0)
+ * due to the configuration of my device.
+ */
+#define SFC_MAX_CHIPSELECT_NUM		4
+
+/* The SFC can transfer max 16KB - 1 at one time
+ * we set it to 15.5KB here for alignment.
+ */
+#define SFC_MAX_IOSIZE_VER3		(512 * 31)
+
+#define SFC_MAX_IOSIZE_VER4		(0xFFFFFFFF)
+
+/* DMA is only enabled for large data transmission */
+#define SFC_DMA_TRANS_THRETHOLD		(0x40)
+
+/* Maximum clock values from datasheet suggest keeping clock value under
+ * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver
+ * has a minimum of 10MHz and a default of 80MHz which seems reasonable.
+ */
+#define SFC_MIN_SPEED_HZ		(10 * 1000 * 1000)
+#define SFC_DEFAULT_SPEED_HZ		(80 * 1000 * 1000)
+#define SFC_MAX_SPEED_HZ		(150 * 1000 * 1000)
+
+struct rockchip_sfc {
+	struct device *dev;
+	void __iomem *regbase;
+	struct clk *hclk;
+	struct clk *clk;
+	u32 frequency;
+	/* virtual mapped addr for dma_buffer */
+	void *buffer;
+	dma_addr_t dma_buffer;
+	struct completion cp;
+	bool use_dma;
+	u32 max_iosize;
+};
+
+static int rockchip_sfc_reset(struct rockchip_sfc *sfc)
+{
+	int err;
+	u32 status;
+
+	writel_relaxed(SFC_RCVR_RESET, sfc->regbase + SFC_RCVR);
+
+	err = readl_poll_timeout(sfc->regbase + SFC_RCVR, status,
+				 !(status & SFC_RCVR_RESET), 20,
+				 jiffies_to_usecs(HZ));
+	if (err)
+		dev_err(sfc->dev, "SFC reset never finished\n");
+
+	/* Still need to clear the masked interrupt from RISR */
+	writel_relaxed(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+
+	dev_dbg(sfc->dev, "reset\n");
+
+	return err;
+}
+
+static u16 rockchip_sfc_get_version(struct rockchip_sfc *sfc)
+{
+	return  (u16)(readl(sfc->regbase + SFC_VER) & 0xffff);
+}
+
+static u32 rockchip_sfc_get_max_iosize(struct rockchip_sfc *sfc)
+{
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
+		return SFC_MAX_IOSIZE_VER4;
+	else
+		return SFC_MAX_IOSIZE_VER3;
+}
+
+static int rockchip_sfc_init(struct rockchip_sfc *sfc)
+{
+	writel(0, sfc->regbase + SFC_CTRL);
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
+		writel(SFC_LEN_CTRL_TRB_SEL, sfc->regbase + SFC_LEN_CTRL);
+
+	return 0;
+}
+
+static inline int rockchip_sfc_get_fifo_level(struct rockchip_sfc *sfc, int wr)
+{
+	u32 fsr = readl_relaxed(sfc->regbase + SFC_FSR);
+	int level;
+
+	if (wr)
+		level = (fsr & SFC_FSR_TXLV_MASK) >> SFC_FSR_TXLV_SHIFT;
+	else
+		level = (fsr & SFC_FSR_RXLV_MASK) >> SFC_FSR_RXLV_SHIFT;
+
+	return level;
+}
+
+static int rockchip_sfc_wait_fifo_ready(struct rockchip_sfc *sfc, int wr, u32 timeout)
+{
+	unsigned long deadline = jiffies + timeout;
+	int level;
+
+	while (!(level = rockchip_sfc_get_fifo_level(sfc, wr))) {
+		if (time_after_eq(jiffies, deadline)) {
+			dev_warn(sfc->dev, "%s fifo timeout\n", wr ? "write" : "read");
+			return -ETIMEDOUT;
+		}
+		udelay(1);
+	}
+
+	return level;
+}
+
+static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc,
+				   struct spi_mem *mem,
+				   const struct spi_mem_op *op,
+				   u32 len)
+{
+	u32 ctrl = 0, cmd = 0;
+
+	/* set CMD */
+	cmd = op->cmd.opcode;
+	ctrl |= ((op->cmd.buswidth >> 1) << SFC_CTRL_CMD_BITS_SHIFT);
+
+	/* set ADDR */
+	if (op->addr.nbytes) {
+		if (op->addr.nbytes == 4) {
+			cmd |= SFC_CMD_ADDR_32BITS << SFC_CMD_ADDR_SHIFT;
+		} else if (op->addr.nbytes == 3) {
+			cmd |= SFC_CMD_ADDR_24BITS << SFC_CMD_ADDR_SHIFT;
+		} else {
+			cmd |= SFC_CMD_ADDR_XBITS << SFC_CMD_ADDR_SHIFT;
+			writel_relaxed(op->addr.nbytes * 8 - 1, sfc->regbase + SFC_ABIT);
+		}
+
+		ctrl |= ((op->addr.buswidth >> 1) << SFC_CTRL_ADDR_BITS_SHIFT);
+	}
+

drivers/spi/spi-rockchip-sfc.c line 290

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+	/* set DUMMY */
+	if (op->dummy.nbytes) {
+		if (op->dummy.buswidth == 4)
+			cmd |= op->dummy.nbytes * 2 << SFC_CMD_DUMMY_SHIFT;
+		else if (op->dummy.buswidth == 2)
+			cmd |= op->dummy.nbytes * 4 << SFC_CMD_DUMMY_SHIFT;
+		else
+			cmd |= op->dummy.nbytes * 8 << SFC_CMD_DUMMY_SHIFT;
+	}
+

I have no experience optimizing code or anything, but would it help here to read the output of rockchip_sfc_get_version() to a variable in the driver data, and then check that each time we hit this? I don't know if there is any real-world difference in reading a variable versus reading a register, so I'm just asking. It's not like the sfc_version will change once the device is probed. :-)

Quoted 167 lines
drivers/spi/spi-rockchip-sfc.c new file +167 -0
+	/* set DATA */
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) /* Clear it if no data to transfer */
+		writel(len, sfc->regbase + SFC_LEN_EXT);
+	else
+		cmd |= len << SFC_CMD_TRAN_BYTES_SHIFT;
+	if (len) {
+		if (op->data.dir == SPI_MEM_DATA_OUT)
+			cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
+
+		ctrl |= ((op->data.buswidth >> 1) << SFC_CTRL_DATA_BITS_SHIFT);
+	}
+	if (!len && op->addr.nbytes)
+		cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
+
+	/* set the Controller */
+	ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE;
+	cmd |= mem->spi->chip_select << SFC_CMD_CS_SHIFT;
+
+	dev_dbg(sfc->dev, "addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n",
+		op->addr.nbytes, op->addr.buswidth,
+		op->dummy.nbytes, op->dummy.buswidth);
+	dev_dbg(sfc->dev, "ctrl=%x cmd=%x addr=%llx len=%x\n",
+		ctrl, cmd, op->addr.val, len);
+
+	writel(ctrl, sfc->regbase + SFC_CTRL);
+	writel(cmd, sfc->regbase + SFC_CMD);
+	if (op->addr.nbytes)
+		writel(op->addr.val, sfc->regbase + SFC_ADDR);
+
+	return 0;
+}
+
+static int rockchip_sfc_write_fifo(struct rockchip_sfc *sfc, const u8 *buf, int len)
+{
+	u8 bytes = len & 0x3;
+	u32 dwords;
+	int tx_level;
+	u32 write_words;
+	u32 tmp = 0;
+
+	dwords = len >> 2;
+	while (dwords) {
+		tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
+		if (tx_level < 0)
+			return tx_level;
+		write_words = min_t(u32, tx_level, dwords);
+		iowrite32_rep(sfc->regbase + SFC_DATA, buf, write_words);
+		buf += write_words << 2;
+		dwords -= write_words;
+	}
+
+	/* write the rest non word aligned bytes */
+	if (bytes) {
+		tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
+		if (tx_level < 0)
+			return tx_level;
+		memcpy(&tmp, buf, bytes);
+		writel(tmp, sfc->regbase + SFC_DATA);
+	}
+
+	return len;
+}
+
+static int rockchip_sfc_read_fifo(struct rockchip_sfc *sfc, u8 *buf, int len)
+{
+	u8 bytes = len & 0x3;
+	u32 dwords;
+	u8 read_words;
+	int rx_level;
+	int tmp;
+
+	/* word aligned access only */
+	dwords = len >> 2;
+	while (dwords) {
+		rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
+		if (rx_level < 0)
+			return rx_level;
+		read_words = min_t(u32, rx_level, dwords);
+		ioread32_rep(sfc->regbase + SFC_DATA, buf, read_words);
+		buf += read_words << 2;
+		dwords -= read_words;
+	}
+
+	/* read the rest non word aligned bytes */
+	if (bytes) {
+		rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
+		if (rx_level < 0)
+			return rx_level;
+		tmp = readl_relaxed(sfc->regbase + SFC_DATA);
+		memcpy(buf, &tmp, bytes);
+	}
+
+	return len;
+}
+
+static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t dma_buf, size_t len)
+{
+	u32 reg;
+	int err = 0;
+
+	init_completion(&sfc->cp);
+
+	writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+
+	/* Enable transfer complete interrupt */
+	reg = readl(sfc->regbase + SFC_IMR);
+	reg &= ~SFC_IMR_DMA;
+	writel(reg, sfc->regbase + SFC_IMR);
+	writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR);
+	writel(0x1, sfc->regbase + SFC_DMA_TRIGGER);
+
+	/* Wait for the interrupt. */
+	if (!wait_for_completion_timeout(&sfc->cp, msecs_to_jiffies(2000))) {
+		dev_err(sfc->dev, "DMA wait for transfer finish timeout\n");
+		err = -ETIMEDOUT;
+	}
+
+	writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+	/* Disable transfer finish interrupt */
+	reg = readl(sfc->regbase + SFC_IMR);
+	reg |= SFC_IMR_DMA;
+	writel(reg, sfc->regbase + SFC_IMR);
+
+	return len;
+}
+
+static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc,
+				       const struct spi_mem_op *op, u32 len)
+{
+	dev_dbg(sfc->dev, "xfer_poll len=%x\n", len);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT)
+		return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len);
+	else
+		return rockchip_sfc_read_fifo(sfc, op->data.buf.in, len);
+}
+
+static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc,
+				      const struct spi_mem_op *op, u32 len)
+{
+	int ret;
+
+	dev_dbg(sfc->dev, "xfer_dma len=%x\n", len);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT) {
+		memcpy_toio(sfc->buffer, op->data.buf.out, len);
+		ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
+	} else {
+		ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
+		memcpy_fromio(op->data.buf.in, sfc->buffer, len);
+	}
+
+	return ret;
+}
+
+static int rockchip_sfc_xfer_done(struct rockchip_sfc *sfc, u32 timeout_us)
+{
+	int ret = 0;
+	u32 status;
+
+	ret = readl_poll_timeout(sfc->regbase + SFC_SR, status,
+				 !(status & SFC_SR_IS_BUSY),
+				 20, timeout_us);
+	if (ret) {
+		dev_err(sfc->dev, "wait sfc idle timeout\n");
+		rockchip_sfc_reset(sfc);
+

drivers/spi/spi-rockchip-sfc.c line 467

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+		ret = -EIO;
+	}
+
+	return ret;
+}
+
+static int rockchip_sfc_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);
+	u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize);

Is it necessary to use the minimum of these 2 values if we use an adjust_op_size which I propose below?

drivers/spi/spi-rockchip-sfc.c line 469

Quoted 2 lines
drivers/spi/spi-rockchip-sfc.c new file +2 -0
+	int ret;
+

Again I'm asking this as someone with no experience optimizing code or with compilers, but would it help to add an unlikely() here? It's all but guaranteed the first time this code path is called the clock will need to be set, but each subsequent call should not really have to care since the clock likely won't be changing (as long as we're on the same CS). We can also then set the sfc->frequency to what the max_speed_hz was after successfully setting the rate so we can hit the faster path after the first run (it looks like it's checking the uninitalized value but never updating it after it's changed, so it's always doing the clk_set_rate()).

Also, should we clamp the clock speed between the min and max values?

Quoted 14 lines
drivers/spi/spi-rockchip-sfc.c new file +14 -0
+	if (mem->spi->max_speed_hz != sfc->frequency) {
+		if (clk_set_rate(sfc->clk, mem->spi->max_speed_hz))
+			return ret;
+		dev_dbg(sfc->dev, "set_freq=%dHz real_freq=%ldHz\n",
+			sfc->frequency, clk_get_rate(sfc->clk));
+	}
+
+	rockchip_sfc_xfer_setup(sfc, mem, op, len);
+	if (len) {
+		if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD)
+			ret = rockchip_sfc_xfer_data_dma(sfc, op, len);
+		else
+			ret = rockchip_sfc_xfer_data_poll(sfc, op, len);
+

drivers/spi/spi-rockchip-sfc.c line 493

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+		if (ret != len) {
+			dev_err(sfc->dev, "xfer data failed ret %d dir %d\n", ret, op->data.dir);
+
+			return -EIO;
+		}
+	}
+
+	return rockchip_sfc_xfer_done(sfc, 100000);
+}
+

I'll be honest with you, I had no idea if I needed this function or not (the rockchip_sfc_get_name() function). I'm pretty sure it's not needed though, so I assume it can be safely removed.

drivers/spi/spi-rockchip-sfc.c line 499

Quoted 6 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+static const char *rockchip_sfc_get_name(struct spi_mem *mem)
+{
+	return devm_kasprintf(&mem->spi->dev, GFP_KERNEL, "%s.%d",
+			      dev_name(&mem->spi->dev), mem->spi->chip_select);
+}
+

I had an issue with doing dd as mentioned above reading against mtd0, and was able to fix it by adding a mem_op of adjust_op_size like this. Not sure if it works for the v4/v5 hardware though.

static int rockchip_sfc_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)

{
	struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);

	op->data.nbytes = min(op->data.nbytes, sfc->max_iosize);
	return 0;
}
Quoted 8 lines
drivers/spi/spi-rockchip-sfc.c new file +8 -0
+static const struct spi_controller_mem_ops rockchip_sfc_mem_ops = {
+	.exec_op = rockchip_sfc_exec_mem_op,
+	.get_name = rockchip_sfc_get_name,
+};
+
+static irqreturn_t rockchip_sfc_irq_handler(int irq, void *dev_id)
+{
+	struct rockchip_sfc *sfc = dev_id;

drivers/spi/spi-rockchip-sfc.c line 517

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+	u32 reg;
+
+	reg = readl(sfc->regbase + SFC_RISR);
+
+	/* Clear interrupt */
+	writel_relaxed(reg, sfc->regbase + SFC_ICLR);
+
+	if (reg & SFC_RISR_DMA)
+		complete(&sfc->cp);
+

From a previous comment, we should only clear the interrupt if we handle the specific one in question.

Quoted 132 lines
drivers/spi/spi-rockchip-sfc.c new file +132 -0
+	return IRQ_HANDLED;
+}
+
+static int rockchip_sfc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spi_master *master;
+	struct resource *res;
+	struct rockchip_sfc *sfc;
+	int ret;
+
+	master = devm_spi_alloc_master(&pdev->dev, sizeof(*sfc));
+	if (!master)
+		return -ENOMEM;
+
+	master->mem_ops = &rockchip_sfc_mem_ops;
+	master->dev.of_node = pdev->dev.of_node;
+	master->mode_bits = SPI_TX_QUAD | SPI_TX_DUAL | SPI_RX_QUAD | SPI_RX_DUAL;
+	master->min_speed_hz = SFC_MIN_SPEED_HZ;
+	master->max_speed_hz = SFC_MAX_SPEED_HZ;
+	master->num_chipselect = SFC_MAX_CHIPSELECT_NUM;
+
+	sfc = spi_master_get_devdata(master);
+	sfc->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	sfc->regbase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(sfc->regbase))
+		return PTR_ERR(sfc->regbase);
+
+	sfc->clk = devm_clk_get(&pdev->dev, "clk_sfc");
+	if (IS_ERR(sfc->clk)) {
+		dev_err(&pdev->dev, "Failed to get sfc interface clk\n");
+		return PTR_ERR(sfc->clk);
+	}
+
+	sfc->hclk = devm_clk_get(&pdev->dev, "hclk_sfc");
+	if (IS_ERR(sfc->hclk)) {
+		dev_err(&pdev->dev, "Failed to get sfc ahb clk\n");
+		return PTR_ERR(sfc->hclk);
+	}
+
+	sfc->use_dma = !of_property_read_bool(sfc->dev->of_node,
+					      "rockchip,sfc-no-dma");
+
+	if (sfc->use_dma) {
+		ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+		if (ret) {
+			dev_warn(dev, "Unable to set dma mask\n");
+			return ret;
+		}
+
+		sfc->buffer = dmam_alloc_coherent(dev, SFC_MAX_IOSIZE_VER3,
+						  &sfc->dma_buffer,
+						  GFP_KERNEL);
+		if (!sfc->buffer)
+			return -ENOMEM;
+	}
+
+	ret = clk_prepare_enable(sfc->hclk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to enable ahb clk\n");
+		goto err_hclk;
+	}
+
+	ret = clk_prepare_enable(sfc->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to enable interface clk\n");
+		goto err_clk;
+	}
+
+	/* Find the irq */
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0) {
+		dev_err(dev, "Failed to get the irq\n");
+		goto err_irq;
+	}
+
+	ret = devm_request_irq(dev, ret, rockchip_sfc_irq_handler,
+			       0, pdev->name, sfc);
+	if (ret) {
+		dev_err(dev, "Failed to request irq\n");
+
+		return ret;
+	}
+
+	ret = rockchip_sfc_init(sfc);
+	if (ret)
+		goto err_irq;
+
+	sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc);
+
+	ret = spi_register_master(master);
+	if (ret)
+		goto err_irq;
+
+	return 0;
+
+err_irq:
+	clk_disable_unprepare(sfc->clk);
+err_clk:
+	clk_disable_unprepare(sfc->hclk);
+err_hclk:
+	return ret;
+}
+
+static int rockchip_sfc_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct rockchip_sfc *sfc = platform_get_drvdata(pdev);
+
+	spi_unregister_master(master);
+
+	clk_disable_unprepare(sfc->clk);
+	clk_disable_unprepare(sfc->hclk);
+
+	return 0;
+}
+
+static const struct of_device_id rockchip_sfc_dt_ids[] = {
+	{ .compatible = "rockchip,px30-sfc"},
+	{ .compatible = "rockchip,rk3036-sfc"},
+	{ .compatible = "rockchip,rk3308-sfc"},
+	{ .compatible = "rockchip,rv1126-sfc"},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rockchip_sfc_dt_ids);
+
+static struct platform_driver rockchip_sfc_driver = {
+	.driver = {
+		.name	= "rockchip-sfc",
+		.of_match_table = rockchip_sfc_dt_ids,

drivers/spi/spi-rockchip-sfc.c line 659

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+	},
+	.probe	= rockchip_sfc_probe,
+	.remove	= rockchip_sfc_remove,
+};
+module_platform_driver(rockchip_sfc_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Rockchip Serial Flash Controller Driver");
+MODULE_AUTHOR("Shawn Lin <[email protected]>");
+MODULE_AUTHOR("Chris Morgan <[email protected]>");

I know folks will hate on me for this (and for good reason given it messes up IDs and stuff), but I prefer [email protected] if my email is in here, as that's the one I've been using for decades...

Quoted 6 lines
drivers/spi/spi-rockchip-sfc.c new file +1 -0
+MODULE_AUTHOR("Jon Lin <[email protected]>");
Signature · 1 line
2.17.1
author
#8 lore raw

Re: [PATCH v6 2/8] spi: rockchip-sfc: add rockchip serial flash controller

Quoted 21 lines · Chris Morgan
Quoted 6 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add the rockchip serial flash controller (SFC) driver.

I think I hit "reply" earlier when I meant to hit "reply-all". Whoops.

I wanted to say that for now this driver is not working for me on the v3 hardware. There appears to be something wrong with alternating between page programs and erase. I can consistently reproduce this by writing a 4MB image of random data to my SPI flash chip at offset c00000 using dd to mtdblock0. I've dumped the contents of what is written to the controller and it appears at some point it goes from doing a page program (02) to a dual io read (bb) to a sector erase (20), then it repeatedly reads the status register (05) and I assume the register never changes. As a result it just keeps looping over the status register then eventually times out. I'm still debugging to try and figure out exactly what is going on though.

Quoted 4 lines

I also noticed that reading does not work consistently using dd from the mtd0 device, however I have a proposed fix for that which I list below at the appropriate section.

Can you enable dev_dbg in rockchip_sfc_xfer_setup, then send me log.

I successfully mount and test spinor jffs2 to confirm read/write/erase work work. I'll try more cases further.

Quoted 341 lines
Quoted 341 lines

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

  drivers/spi/Kconfig            |   9 +
  drivers/spi/Makefile           |   1 +
  drivers/spi/spi-rockchip-sfc.c | 660 +++++++++++++++++++++++++++++++++
  3 files changed, 670 insertions(+)

create mode 100644 drivers/spi/spi-rockchip-sfc.c

drivers/spi/Kconfig +9 -0
index e71a4c514f7b..d89e5f3c9107 100644
@@ -658,6 +658,15 @@ config SPI_ROCKCHIP
  	  The main usecase of this controller is to use spi flash as boot
  	  device.
 
+config SPI_ROCKCHIP_SFC
+	tristate "Rockchip Serial Flash Controller (SFC)"
+	depends on ARCH_ROCKCHIP || COMPILE_TEST
+	depends on HAS_IOMEM && HAS_DMA
+	help
+	  This enables support for Rockchip serial flash controller. This
+	  is a specialized controller used to access SPI flash on some
+	  Rockchip SOCs.
+
  config SPI_RB4XX
  	tristate "Mikrotik RB4XX SPI master"
  	depends on SPI_MASTER && ATH79
drivers/spi/Makefile +1 -0
index 13e54c45e9df..699db95c8441 100644
@@ -95,6 +95,7 @@ obj-$(CONFIG_SPI_QCOM_GENI)		+= spi-geni-qcom.o
  obj-$(CONFIG_SPI_QCOM_QSPI)		+= spi-qcom-qspi.o
  obj-$(CONFIG_SPI_QUP)			+= spi-qup.o
  obj-$(CONFIG_SPI_ROCKCHIP)		+= spi-rockchip.o
+obj-$(CONFIG_SPI_ROCKCHIP_SFC)		+= spi-rockchip-sfc.o
  obj-$(CONFIG_SPI_RB4XX)			+= spi-rb4xx.o
  obj-$(CONFIG_MACH_REALTEK_RTL)		+= spi-realtek-rtl.o
  obj-$(CONFIG_SPI_RPCIF)			+= spi-rpc-if.o
drivers/spi/spi-rockchip-sfc.c new file +288 -0
new file mode 100644
index 000000000000..ec25ad278096
@@ -0,0 +1,660 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Rockchip Serial Flash Controller Driver
+ *
+ * Copyright (c) 2017-2021, Rockchip Inc.
+ * Author: Shawn Lin <[email protected]>
+ *	   Chris Morgan <[email protected]>
+ *	   Jon Lin <[email protected]>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi-mem.h>
+
+/* System control */
+#define SFC_CTRL			0x0
+#define  SFC_CTRL_PHASE_SEL_NEGETIVE	BIT(1)
+#define  SFC_CTRL_CMD_BITS_SHIFT	8
+#define  SFC_CTRL_ADDR_BITS_SHIFT	10
+#define  SFC_CTRL_DATA_BITS_SHIFT	12
+
+/* Interrupt mask */
+#define SFC_IMR				0x4
+#define  SFC_IMR_RX_FULL		BIT(0)
+#define  SFC_IMR_RX_UFLOW		BIT(1)
+#define  SFC_IMR_TX_OFLOW		BIT(2)
+#define  SFC_IMR_TX_EMPTY		BIT(3)
+#define  SFC_IMR_TRAN_FINISH		BIT(4)
+#define  SFC_IMR_BUS_ERR		BIT(5)
+#define  SFC_IMR_NSPI_ERR		BIT(6)
+#define  SFC_IMR_DMA			BIT(7)
+
+/* Interrupt clear */
+#define SFC_ICLR			0x8
+#define  SFC_ICLR_RX_FULL		BIT(0)
+#define  SFC_ICLR_RX_UFLOW		BIT(1)
+#define  SFC_ICLR_TX_OFLOW		BIT(2)
+#define  SFC_ICLR_TX_EMPTY		BIT(3)
+#define  SFC_ICLR_TRAN_FINISH		BIT(4)
+#define  SFC_ICLR_BUS_ERR		BIT(5)
+#define  SFC_ICLR_NSPI_ERR		BIT(6)
+#define  SFC_ICLR_DMA			BIT(7)
+
+/* FIFO threshold level */
+#define SFC_FTLR			0xc
+#define  SFC_FTLR_TX_SHIFT		0
+#define  SFC_FTLR_TX_MASK		0x1f
+#define  SFC_FTLR_RX_SHIFT		8
+#define  SFC_FTLR_RX_MASK		0x1f
+
+/* Reset FSM and FIFO */
+#define SFC_RCVR			0x10
+#define  SFC_RCVR_RESET			BIT(0)
+
+/* Enhanced mode */
+#define SFC_AX				0x14
+
+/* Address Bit number */
+#define SFC_ABIT			0x18
+
+/* Interrupt status */
+#define SFC_ISR				0x1c
+#define  SFC_ISR_RX_FULL_SHIFT		BIT(0)
+#define  SFC_ISR_RX_UFLOW_SHIFT		BIT(1)
+#define  SFC_ISR_TX_OFLOW_SHIFT		BIT(2)
+#define  SFC_ISR_TX_EMPTY_SHIFT		BIT(3)
+#define  SFC_ISR_TX_FINISH_SHIFT	BIT(4)
+#define  SFC_ISR_BUS_ERR_SHIFT		BIT(5)
+#define  SFC_ISR_NSPI_ERR_SHIFT		BIT(6)
+#define  SFC_ISR_DMA_SHIFT		BIT(7)
+
+/* FIFO status */
+#define SFC_FSR				0x20
+#define  SFC_FSR_TX_IS_FULL		BIT(0)
+#define  SFC_FSR_TX_IS_EMPTY		BIT(1)
+#define  SFC_FSR_RX_IS_EMPTY		BIT(2)
+#define  SFC_FSR_RX_IS_FULL		BIT(3)
+#define  SFC_FSR_TXLV_MASK		GENMASK(12, 8)
+#define  SFC_FSR_TXLV_SHIFT		8
+#define  SFC_FSR_RXLV_MASK		GENMASK(20, 16)
+#define  SFC_FSR_RXLV_SHIFT		16
+
+/* FSM status */
+#define SFC_SR				0x24
+#define  SFC_SR_IS_IDLE			0x0
+#define  SFC_SR_IS_BUSY			0x1
+
+/* Raw interrupt status */
+#define SFC_RISR			0x28
+#define  SFC_RISR_RX_FULL		BIT(0)
+#define  SFC_RISR_RX_UNDERFLOW		BIT(1)
+#define  SFC_RISR_TX_OVERFLOW		BIT(2)
+#define  SFC_RISR_TX_EMPTY		BIT(3)
+#define  SFC_RISR_TRAN_FINISH		BIT(4)
+#define  SFC_RISR_BUS_ERR		BIT(5)
+#define  SFC_RISR_NSPI_ERR		BIT(6)
+#define  SFC_RISR_DMA			BIT(7)
+
+/* Version */
+#define SFC_VER				0x2C
+#define  SFC_VER_3			0x3
+#define  SFC_VER_4			0x4
+#define  SFC_VER_5			0x5
+
+/* Master trigger */
+#define SFC_DMA_TRIGGER			0x80
+
+/* Src or Dst addr for master */
+#define SFC_DMA_ADDR			0x84
+
+/* Length control register extension 32GB */
+#define SFC_LEN_CTRL			0x88
+#define SFC_LEN_CTRL_TRB_SEL		1
+#define SFC_LEN_EXT			0x8C
+
+/* Command */
+#define SFC_CMD				0x100
+#define  SFC_CMD_IDX_SHIFT		0
+#define  SFC_CMD_DUMMY_SHIFT		8
+#define  SFC_CMD_DIR_SHIFT		12
+#define  SFC_CMD_DIR_RD			0
+#define  SFC_CMD_DIR_WR			1
+#define  SFC_CMD_ADDR_SHIFT		14
+#define  SFC_CMD_ADDR_0BITS		0
+#define  SFC_CMD_ADDR_24BITS		1
+#define  SFC_CMD_ADDR_32BITS		2
+#define  SFC_CMD_ADDR_XBITS		3
+#define  SFC_CMD_TRAN_BYTES_SHIFT	16
+#define  SFC_CMD_CS_SHIFT		30
+
+/* Address */
+#define SFC_ADDR			0x104
+
+/* Data */
+#define SFC_DATA			0x108
+
+/* The controller and documentation reports that it supports up to 4 CS
+ * devices (0-3), however I have only been able to test a single CS (CS 0)
+ * due to the configuration of my device.
+ */
+#define SFC_MAX_CHIPSELECT_NUM		4
+
+/* The SFC can transfer max 16KB - 1 at one time
+ * we set it to 15.5KB here for alignment.
+ */
+#define SFC_MAX_IOSIZE_VER3		(512 * 31)
+
+#define SFC_MAX_IOSIZE_VER4		(0xFFFFFFFF)
+
+/* DMA is only enabled for large data transmission */
+#define SFC_DMA_TRANS_THRETHOLD		(0x40)
+
+/* Maximum clock values from datasheet suggest keeping clock value under
+ * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver
+ * has a minimum of 10MHz and a default of 80MHz which seems reasonable.
+ */
+#define SFC_MIN_SPEED_HZ		(10 * 1000 * 1000)
+#define SFC_DEFAULT_SPEED_HZ		(80 * 1000 * 1000)
+#define SFC_MAX_SPEED_HZ		(150 * 1000 * 1000)
+
+struct rockchip_sfc {
+	struct device *dev;
+	void __iomem *regbase;
+	struct clk *hclk;
+	struct clk *clk;
+	u32 frequency;
+	/* virtual mapped addr for dma_buffer */
+	void *buffer;
+	dma_addr_t dma_buffer;
+	struct completion cp;
+	bool use_dma;
+	u32 max_iosize;
+};
+
+static int rockchip_sfc_reset(struct rockchip_sfc *sfc)
+{
+	int err;
+	u32 status;
+
+	writel_relaxed(SFC_RCVR_RESET, sfc->regbase + SFC_RCVR);
+
+	err = readl_poll_timeout(sfc->regbase + SFC_RCVR, status,
+				 !(status & SFC_RCVR_RESET), 20,
+				 jiffies_to_usecs(HZ));
+	if (err)
+		dev_err(sfc->dev, "SFC reset never finished\n");
+
+	/* Still need to clear the masked interrupt from RISR */
+	writel_relaxed(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+
+	dev_dbg(sfc->dev, "reset\n");
+
+	return err;
+}
+
+static u16 rockchip_sfc_get_version(struct rockchip_sfc *sfc)
+{
+	return  (u16)(readl(sfc->regbase + SFC_VER) & 0xffff);
+}
+
+static u32 rockchip_sfc_get_max_iosize(struct rockchip_sfc *sfc)
+{
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
+		return SFC_MAX_IOSIZE_VER4;
+	else
+		return SFC_MAX_IOSIZE_VER3;
+}
+
+static int rockchip_sfc_init(struct rockchip_sfc *sfc)
+{
+	writel(0, sfc->regbase + SFC_CTRL);
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
+		writel(SFC_LEN_CTRL_TRB_SEL, sfc->regbase + SFC_LEN_CTRL);
+
+	return 0;
+}
+
+static inline int rockchip_sfc_get_fifo_level(struct rockchip_sfc *sfc, int wr)
+{
+	u32 fsr = readl_relaxed(sfc->regbase + SFC_FSR);
+	int level;
+
+	if (wr)
+		level = (fsr & SFC_FSR_TXLV_MASK) >> SFC_FSR_TXLV_SHIFT;
+	else
+		level = (fsr & SFC_FSR_RXLV_MASK) >> SFC_FSR_RXLV_SHIFT;
+
+	return level;
+}
+
+static int rockchip_sfc_wait_fifo_ready(struct rockchip_sfc *sfc, int wr, u32 timeout)
+{
+	unsigned long deadline = jiffies + timeout;
+	int level;
+
+	while (!(level = rockchip_sfc_get_fifo_level(sfc, wr))) {
+		if (time_after_eq(jiffies, deadline)) {
+			dev_warn(sfc->dev, "%s fifo timeout\n", wr ? "write" : "read");
+			return -ETIMEDOUT;
+		}
+		udelay(1);
+	}
+
+	return level;
+}
+
+static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc,
+				   struct spi_mem *mem,
+				   const struct spi_mem_op *op,
+				   u32 len)
+{
+	u32 ctrl = 0, cmd = 0;
+
+	/* set CMD */
+	cmd = op->cmd.opcode;
+	ctrl |= ((op->cmd.buswidth >> 1) << SFC_CTRL_CMD_BITS_SHIFT);
+
+	/* set ADDR */
+	if (op->addr.nbytes) {
+		if (op->addr.nbytes == 4) {
+			cmd |= SFC_CMD_ADDR_32BITS << SFC_CMD_ADDR_SHIFT;
+		} else if (op->addr.nbytes == 3) {
+			cmd |= SFC_CMD_ADDR_24BITS << SFC_CMD_ADDR_SHIFT;
+		} else {
+			cmd |= SFC_CMD_ADDR_XBITS << SFC_CMD_ADDR_SHIFT;
+			writel_relaxed(op->addr.nbytes * 8 - 1, sfc->regbase + SFC_ABIT);
+		}
+
+		ctrl |= ((op->addr.buswidth >> 1) << SFC_CTRL_ADDR_BITS_SHIFT);
+	}
+
+	/* set DUMMY */
+	if (op->dummy.nbytes) {
+		if (op->dummy.buswidth == 4)
+			cmd |= op->dummy.nbytes * 2 << SFC_CMD_DUMMY_SHIFT;
+		else if (op->dummy.buswidth == 2)
+			cmd |= op->dummy.nbytes * 4 << SFC_CMD_DUMMY_SHIFT;
+		else
+			cmd |= op->dummy.nbytes * 8 << SFC_CMD_DUMMY_SHIFT;
Quoted 8 lines

drivers/spi/spi-rockchip-sfc.c line 290

Quoted 2 lines
drivers/spi/spi-rockchip-sfc.c new file +2 -0
+	}
+

I have no experience optimizing code or anything, but would it help here to read the output of rockchip_sfc_get_version() to a variable in the driver data, and then check that each time we hit this? I don't know if there is any real-world difference in reading a variable versus reading a register, so I'm just asking. It's not like the sfc_version will change once the device is probed. :-)

done.

Quoted 171 lines
Quoted 171 lines
drivers/spi/spi-rockchip-sfc.c new file +171 -0
+	/* set DATA */
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) /* Clear it if no data to transfer */
+		writel(len, sfc->regbase + SFC_LEN_EXT);
+	else
+		cmd |= len << SFC_CMD_TRAN_BYTES_SHIFT;
+	if (len) {
+		if (op->data.dir == SPI_MEM_DATA_OUT)
+			cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
+
+		ctrl |= ((op->data.buswidth >> 1) << SFC_CTRL_DATA_BITS_SHIFT);
+	}
+	if (!len && op->addr.nbytes)
+		cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
+
+	/* set the Controller */
+	ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE;
+	cmd |= mem->spi->chip_select << SFC_CMD_CS_SHIFT;
+
+	dev_dbg(sfc->dev, "addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n",
+		op->addr.nbytes, op->addr.buswidth,
+		op->dummy.nbytes, op->dummy.buswidth);
+	dev_dbg(sfc->dev, "ctrl=%x cmd=%x addr=%llx len=%x\n",
+		ctrl, cmd, op->addr.val, len);
+
+	writel(ctrl, sfc->regbase + SFC_CTRL);
+	writel(cmd, sfc->regbase + SFC_CMD);
+	if (op->addr.nbytes)
+		writel(op->addr.val, sfc->regbase + SFC_ADDR);
+
+	return 0;
+}
+
+static int rockchip_sfc_write_fifo(struct rockchip_sfc *sfc, const u8 *buf, int len)
+{
+	u8 bytes = len & 0x3;
+	u32 dwords;
+	int tx_level;
+	u32 write_words;
+	u32 tmp = 0;
+
+	dwords = len >> 2;
+	while (dwords) {
+		tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
+		if (tx_level < 0)
+			return tx_level;
+		write_words = min_t(u32, tx_level, dwords);
+		iowrite32_rep(sfc->regbase + SFC_DATA, buf, write_words);
+		buf += write_words << 2;
+		dwords -= write_words;
+	}
+
+	/* write the rest non word aligned bytes */
+	if (bytes) {
+		tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
+		if (tx_level < 0)
+			return tx_level;
+		memcpy(&tmp, buf, bytes);
+		writel(tmp, sfc->regbase + SFC_DATA);
+	}
+
+	return len;
+}
+
+static int rockchip_sfc_read_fifo(struct rockchip_sfc *sfc, u8 *buf, int len)
+{
+	u8 bytes = len & 0x3;
+	u32 dwords;
+	u8 read_words;
+	int rx_level;
+	int tmp;
+
+	/* word aligned access only */
+	dwords = len >> 2;
+	while (dwords) {
+		rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
+		if (rx_level < 0)
+			return rx_level;
+		read_words = min_t(u32, rx_level, dwords);
+		ioread32_rep(sfc->regbase + SFC_DATA, buf, read_words);
+		buf += read_words << 2;
+		dwords -= read_words;
+	}
+
+	/* read the rest non word aligned bytes */
+	if (bytes) {
+		rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
+		if (rx_level < 0)
+			return rx_level;
+		tmp = readl_relaxed(sfc->regbase + SFC_DATA);
+		memcpy(buf, &tmp, bytes);
+	}
+
+	return len;
+}
+
+static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t dma_buf, size_t len)
+{
+	u32 reg;
+	int err = 0;
+
+	init_completion(&sfc->cp);
+
+	writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+
+	/* Enable transfer complete interrupt */
+	reg = readl(sfc->regbase + SFC_IMR);
+	reg &= ~SFC_IMR_DMA;
+	writel(reg, sfc->regbase + SFC_IMR);
+	writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR);
+	writel(0x1, sfc->regbase + SFC_DMA_TRIGGER);
+
+	/* Wait for the interrupt. */
+	if (!wait_for_completion_timeout(&sfc->cp, msecs_to_jiffies(2000))) {
+		dev_err(sfc->dev, "DMA wait for transfer finish timeout\n");
+		err = -ETIMEDOUT;
+	}
+
+	writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+	/* Disable transfer finish interrupt */
+	reg = readl(sfc->regbase + SFC_IMR);
+	reg |= SFC_IMR_DMA;
+	writel(reg, sfc->regbase + SFC_IMR);
+
+	return len;
+}
+
+static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc,
+				       const struct spi_mem_op *op, u32 len)
+{
+	dev_dbg(sfc->dev, "xfer_poll len=%x\n", len);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT)
+		return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len);
+	else
+		return rockchip_sfc_read_fifo(sfc, op->data.buf.in, len);
+}
+
+static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc,
+				      const struct spi_mem_op *op, u32 len)
+{
+	int ret;
+
+	dev_dbg(sfc->dev, "xfer_dma len=%x\n", len);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT) {
+		memcpy_toio(sfc->buffer, op->data.buf.out, len);
+		ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
+	} else {
+		ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
+		memcpy_fromio(op->data.buf.in, sfc->buffer, len);
+	}
+
+	return ret;
+}
+
+static int rockchip_sfc_xfer_done(struct rockchip_sfc *sfc, u32 timeout_us)
+{
+	int ret = 0;
+	u32 status;
+
+	ret = readl_poll_timeout(sfc->regbase + SFC_SR, status,
+				 !(status & SFC_SR_IS_BUSY),
+				 20, timeout_us);
+	if (ret) {
+		dev_err(sfc->dev, "wait sfc idle timeout\n");
+		rockchip_sfc_reset(sfc);
+
+		ret = -EIO;
+	}
+
+	return ret;
Quoted 8 lines

drivers/spi/spi-rockchip-sfc.c line 467

Quoted 6 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+}
+
+static int rockchip_sfc_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);
+	u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize);

Is it necessary to use the minimum of these 2 values if we use an adjust_op_size which I propose below?

it necessary if use adjust_op_size, done.

Quoted 13 lines

drivers/spi/spi-rockchip-sfc.c line 469

Quoted 2 lines
drivers/spi/spi-rockchip-sfc.c new file +2 -0
+	int ret;
+

Again I'm asking this as someone with no experience optimizing code or with compilers, but would it help to add an unlikely() here? It's all but guaranteed the first time this code path is called the clock will need to be set, but each subsequent call should not really have to care since the clock likely won't be changing (as long as we're on the same CS). We can also then set the sfc->frequency to what the max_speed_hz was after successfully setting the rate so we can hit the faster path after the first run (it looks like it's checking the uninitalized value but never updating it after it's changed, so it's always doing the clk_set_rate()).

Quoted 1 line

Also, should we clamp the clock speed between the min and max values?

done.

Quoted 38 lines
Quoted 14 lines
drivers/spi/spi-rockchip-sfc.c new file +14 -0
+	if (mem->spi->max_speed_hz != sfc->frequency) {
+		if (clk_set_rate(sfc->clk, mem->spi->max_speed_hz))
+			return ret;
+		dev_dbg(sfc->dev, "set_freq=%dHz real_freq=%ldHz\n",
+			sfc->frequency, clk_get_rate(sfc->clk));
+	}
+
+	rockchip_sfc_xfer_setup(sfc, mem, op, len);
+	if (len) {
+		if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD)
+			ret = rockchip_sfc_xfer_data_dma(sfc, op, len);
+		else
+			ret = rockchip_sfc_xfer_data_poll(sfc, op, len);
+

drivers/spi/spi-rockchip-sfc.c line 493

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+		if (ret != len) {
+			dev_err(sfc->dev, "xfer data failed ret %d dir %d\n", ret, op->data.dir);
+
+			return -EIO;
+		}
+	}
+
+	return rockchip_sfc_xfer_done(sfc, 100000);
+}
+

I'll be honest with you, I had no idea if I needed this function or not (the rockchip_sfc_get_name() function). I'm pretty sure it's not needed though, so I assume it can be safely removed.

drivers/spi/spi-rockchip-sfc.c line 499

Quoted 6 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+static const char *rockchip_sfc_get_name(struct spi_mem *mem)
+{
+	return devm_kasprintf(&mem->spi->dev, GFP_KERNEL, "%s.%d",
+			      dev_name(&mem->spi->dev), mem->spi->chip_select);
+}
+

I had an issue with doing dd as mentioned above reading against mtd0, and was able to fix it by adding a mem_op of adjust_op_size like this. Not sure if it works for the v4/v5 hardware though.

Quoted 7 lines

static int rockchip_sfc_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)

{
	struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);

	op->data.nbytes = min(op->data.nbytes, sfc->max_iosize);
	return 0;
}

good idea.

Quoted 12 lines
Quoted 12 lines
drivers/spi/spi-rockchip-sfc.c new file +12 -0
+static const struct spi_controller_mem_ops rockchip_sfc_mem_ops = {
+	.exec_op = rockchip_sfc_exec_mem_op,
+	.get_name = rockchip_sfc_get_name,
+};
+
+static irqreturn_t rockchip_sfc_irq_handler(int irq, void *dev_id)
+{
+	struct rockchip_sfc *sfc = dev_id;
+	u32 reg;
+
+	reg = readl(sfc->regbase + SFC_RISR);
+
Quoted 9 lines
Quoted 7 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+	/* Clear interrupt */
+	writel_relaxed(reg, sfc->regbase + SFC_ICLR);
+
+	if (reg & SFC_RISR_DMA)
+		complete(&sfc->cp);
+

From a previous comment, we should only clear the interrupt if we

handle the specific one in question.

Compare with drivers/spi/spi-cadence-quadspi.c, I think the former code work well. Can explain more for the reason.

Quoted 137 lines
Quoted 137 lines
drivers/spi/spi-rockchip-sfc.c new file +137 -0
+	return IRQ_HANDLED;
+}
+
+static int rockchip_sfc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spi_master *master;
+	struct resource *res;
+	struct rockchip_sfc *sfc;
+	int ret;
+
+	master = devm_spi_alloc_master(&pdev->dev, sizeof(*sfc));
+	if (!master)
+		return -ENOMEM;
+
+	master->mem_ops = &rockchip_sfc_mem_ops;
+	master->dev.of_node = pdev->dev.of_node;
+	master->mode_bits = SPI_TX_QUAD | SPI_TX_DUAL | SPI_RX_QUAD | SPI_RX_DUAL;
+	master->min_speed_hz = SFC_MIN_SPEED_HZ;
+	master->max_speed_hz = SFC_MAX_SPEED_HZ;
+	master->num_chipselect = SFC_MAX_CHIPSELECT_NUM;
+
+	sfc = spi_master_get_devdata(master);
+	sfc->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	sfc->regbase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(sfc->regbase))
+		return PTR_ERR(sfc->regbase);
+
+	sfc->clk = devm_clk_get(&pdev->dev, "clk_sfc");
+	if (IS_ERR(sfc->clk)) {
+		dev_err(&pdev->dev, "Failed to get sfc interface clk\n");
+		return PTR_ERR(sfc->clk);
+	}
+
+	sfc->hclk = devm_clk_get(&pdev->dev, "hclk_sfc");
+	if (IS_ERR(sfc->hclk)) {
+		dev_err(&pdev->dev, "Failed to get sfc ahb clk\n");
+		return PTR_ERR(sfc->hclk);
+	}
+
+	sfc->use_dma = !of_property_read_bool(sfc->dev->of_node,
+					      "rockchip,sfc-no-dma");
+
+	if (sfc->use_dma) {
+		ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+		if (ret) {
+			dev_warn(dev, "Unable to set dma mask\n");
+			return ret;
+		}
+
+		sfc->buffer = dmam_alloc_coherent(dev, SFC_MAX_IOSIZE_VER3,
+						  &sfc->dma_buffer,
+						  GFP_KERNEL);
+		if (!sfc->buffer)
+			return -ENOMEM;
+	}
+
+	ret = clk_prepare_enable(sfc->hclk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to enable ahb clk\n");
+		goto err_hclk;
+	}
+
+	ret = clk_prepare_enable(sfc->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to enable interface clk\n");
+		goto err_clk;
+	}
+
+	/* Find the irq */
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0) {
+		dev_err(dev, "Failed to get the irq\n");
+		goto err_irq;
+	}
+
+	ret = devm_request_irq(dev, ret, rockchip_sfc_irq_handler,
+			       0, pdev->name, sfc);
+	if (ret) {
+		dev_err(dev, "Failed to request irq\n");
+
+		return ret;
+	}
+
+	ret = rockchip_sfc_init(sfc);
+	if (ret)
+		goto err_irq;
+
+	sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc);
+
+	ret = spi_register_master(master);
+	if (ret)
+		goto err_irq;
+
+	return 0;
+
+err_irq:
+	clk_disable_unprepare(sfc->clk);
+err_clk:
+	clk_disable_unprepare(sfc->hclk);
+err_hclk:
+	return ret;
+}
+
+static int rockchip_sfc_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct rockchip_sfc *sfc = platform_get_drvdata(pdev);
+
+	spi_unregister_master(master);
+
+	clk_disable_unprepare(sfc->clk);
+	clk_disable_unprepare(sfc->hclk);
+
+	return 0;
+}
+
+static const struct of_device_id rockchip_sfc_dt_ids[] = {
+	{ .compatible = "rockchip,px30-sfc"},
+	{ .compatible = "rockchip,rk3036-sfc"},
+	{ .compatible = "rockchip,rk3308-sfc"},
+	{ .compatible = "rockchip,rv1126-sfc"},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rockchip_sfc_dt_ids);
+
+static struct platform_driver rockchip_sfc_driver = {
+	.driver = {
+		.name	= "rockchip-sfc",
+		.of_match_table = rockchip_sfc_dt_ids,
+	},
+	.probe	= rockchip_sfc_probe,
+	.remove	= rockchip_sfc_remove,
+};
+module_platform_driver(rockchip_sfc_driver);
Quoted 8 lines

drivers/spi/spi-rockchip-sfc.c line 659

Quoted 5 lines
drivers/spi/spi-rockchip-sfc.c new file +5 -0
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Rockchip Serial Flash Controller Driver");
+MODULE_AUTHOR("Shawn Lin <[email protected]>");
+MODULE_AUTHOR("Chris Morgan <[email protected]>");

I know folks will hate on me for this (and for good reason given it messes up IDs and stuff), but I prefer [email protected] if my email is in here, as that's the one I've been using for decades...

ok.

Quoted 8 lines
Quoted 6 lines

+MODULE_AUTHOR("Jon Lin <[email protected]>");

Signature · 1 line
2.17.1
#9 lore raw

Re: [PATCH v6 2/8] spi: rockchip-sfc: add rockchip serial flash controller

Quoted 23 lines · Jon Lin
Quoted 21 lines · Chris Morgan
Quoted 6 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add the rockchip serial flash controller (SFC) driver.

I think I hit "reply" earlier when I meant to hit "reply-all". Whoops.

I wanted to say that for now this driver is not working for me on the v3 hardware. There appears to be something wrong with alternating between page programs and erase. I can consistently reproduce this by writing a 4MB image of random data to my SPI flash chip at offset c00000 using dd to mtdblock0. I've dumped the contents of what is written to the controller and it appears at some point it goes from doing a page program (02) to a dual io read (bb) to a sector erase (20), then it repeatedly reads the status register (05) and I assume the register never changes. As a result it just keeps looping over the status register then eventually times out. I'm still debugging to try and figure out exactly what is going on though.

Quoted 5 lines
Quoted 4 lines

I also noticed that reading does not work consistently using dd from the mtd0 device, however I have a proposed fix for that which I list below at the appropriate section.

Can you enable dev_dbg in rockchip_sfc_xfer_setup, then send me log.

I can confirm that on the v7 patch I still get some "weirdness" when I use mtdblock, but when I use flashrom things work entirely as expected. I will still send you a log, but at this point I wonder if it's related to an mtdblock issue rather than an issue with this driver. In retrospect I don't recall testing things this extensively earlier.

You can reproduce the issue by doing the following:

Create a random 4MB file (dd if=/dev/urandom of=rand.img bs=4M count=1)

Write the 4MB random file to the device using MTD Block drivers (dd if=rand.img of=/dev/mtdblock0 bs=4096 seek=3072)

Read back the data (dd if=/dev/mtd0 of=rand1.img bs=4096 skip=3072)

Compare checksums (md5sum *.img)
When I do this I get different checksums for the random files. However when I use flashrom to write instead of MTD Block, it works.

Read the ROM - I can confirm after extensive testing reads seem to work just fine (dd if=/dev/mtd0 of=rom.img bs=8192)

Copy the random data to the image file
(dd if=rand.img of=rom.img bs=4096 seek=3072)

Flash the file with flashrom (flashrom -p linux_mtd -w rom.img)

Read back the random data
(dd if=/dev/mtd0 of=rand1.img bs=4096 skip=3072)

Compare checksums (md5sum *.img)
At this point the rand.img and rand1.img files have identical checksums.

As for testing the reading bugs I found on v6 and below, it was a matter of reading with dd using a block size bigger than the max_iosize value, but with the addition of the adjust_op_size that seems to be resolved now completely.

Test case:
Read flash image with varying block sizes
(dd if=/dev/mtd0 of=test1.img bs=4096)
(dd if=/dev/mtd0 of=test2.img bs=8192)
(dd if=/dev/mtd0 of=test3.img bs=16384)

Compare checksums (md5sum *.img)

Prior to v7 the checksum for test3.img would be different than the other two. v7 now returns the same checksum for all 3 files.

Quoted 778 lines

I successfully mount and test spinor jffs2 to confirm read/write/erase work work. I'll try more cases further.

Quoted 340 lines
Quoted 340 lines

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

  drivers/spi/Kconfig            |   9 +
  drivers/spi/Makefile           |   1 +
  drivers/spi/spi-rockchip-sfc.c | 660 +++++++++++++++++++++++++++++++++
  3 files changed, 670 insertions(+)

create mode 100644 drivers/spi/spi-rockchip-sfc.c

drivers/spi/Kconfig +9 -0
index e71a4c514f7b..d89e5f3c9107 100644
@@ -658,6 +658,15 @@ config SPI_ROCKCHIP
  	  The main usecase of this controller is to use spi flash as boot
  	  device.
+config SPI_ROCKCHIP_SFC
+	tristate "Rockchip Serial Flash Controller (SFC)"
+	depends on ARCH_ROCKCHIP || COMPILE_TEST
+	depends on HAS_IOMEM && HAS_DMA
+	help
+	  This enables support for Rockchip serial flash controller. This
+	  is a specialized controller used to access SPI flash on some
+	  Rockchip SOCs.
+
  config SPI_RB4XX
  	tristate "Mikrotik RB4XX SPI master"
  	depends on SPI_MASTER && ATH79
drivers/spi/Makefile +1 -0
index 13e54c45e9df..699db95c8441 100644
@@ -95,6 +95,7 @@ obj-$(CONFIG_SPI_QCOM_GENI)		+= spi-geni-qcom.o
  obj-$(CONFIG_SPI_QCOM_QSPI)		+= spi-qcom-qspi.o
  obj-$(CONFIG_SPI_QUP)			+= spi-qup.o
  obj-$(CONFIG_SPI_ROCKCHIP)		+= spi-rockchip.o
+obj-$(CONFIG_SPI_ROCKCHIP_SFC)		+= spi-rockchip-sfc.o
  obj-$(CONFIG_SPI_RB4XX)			+= spi-rb4xx.o
  obj-$(CONFIG_MACH_REALTEK_RTL)		+= spi-realtek-rtl.o
  obj-$(CONFIG_SPI_RPCIF)			+= spi-rpc-if.o
drivers/spi/spi-rockchip-sfc.c new file +288 -0
new file mode 100644
index 000000000000..ec25ad278096
@@ -0,0 +1,660 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Rockchip Serial Flash Controller Driver
+ *
+ * Copyright (c) 2017-2021, Rockchip Inc.
+ * Author: Shawn Lin <[email protected]>
+ *	   Chris Morgan <[email protected]>
+ *	   Jon Lin <[email protected]>
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/dma-mapping.h>
+#include <linux/iopoll.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/spi/spi-mem.h>
+
+/* System control */
+#define SFC_CTRL			0x0
+#define  SFC_CTRL_PHASE_SEL_NEGETIVE	BIT(1)
+#define  SFC_CTRL_CMD_BITS_SHIFT	8
+#define  SFC_CTRL_ADDR_BITS_SHIFT	10
+#define  SFC_CTRL_DATA_BITS_SHIFT	12
+
+/* Interrupt mask */
+#define SFC_IMR				0x4
+#define  SFC_IMR_RX_FULL		BIT(0)
+#define  SFC_IMR_RX_UFLOW		BIT(1)
+#define  SFC_IMR_TX_OFLOW		BIT(2)
+#define  SFC_IMR_TX_EMPTY		BIT(3)
+#define  SFC_IMR_TRAN_FINISH		BIT(4)
+#define  SFC_IMR_BUS_ERR		BIT(5)
+#define  SFC_IMR_NSPI_ERR		BIT(6)
+#define  SFC_IMR_DMA			BIT(7)
+
+/* Interrupt clear */
+#define SFC_ICLR			0x8
+#define  SFC_ICLR_RX_FULL		BIT(0)
+#define  SFC_ICLR_RX_UFLOW		BIT(1)
+#define  SFC_ICLR_TX_OFLOW		BIT(2)
+#define  SFC_ICLR_TX_EMPTY		BIT(3)
+#define  SFC_ICLR_TRAN_FINISH		BIT(4)
+#define  SFC_ICLR_BUS_ERR		BIT(5)
+#define  SFC_ICLR_NSPI_ERR		BIT(6)
+#define  SFC_ICLR_DMA			BIT(7)
+
+/* FIFO threshold level */
+#define SFC_FTLR			0xc
+#define  SFC_FTLR_TX_SHIFT		0
+#define  SFC_FTLR_TX_MASK		0x1f
+#define  SFC_FTLR_RX_SHIFT		8
+#define  SFC_FTLR_RX_MASK		0x1f
+
+/* Reset FSM and FIFO */
+#define SFC_RCVR			0x10
+#define  SFC_RCVR_RESET			BIT(0)
+
+/* Enhanced mode */
+#define SFC_AX				0x14
+
+/* Address Bit number */
+#define SFC_ABIT			0x18
+
+/* Interrupt status */
+#define SFC_ISR				0x1c
+#define  SFC_ISR_RX_FULL_SHIFT		BIT(0)
+#define  SFC_ISR_RX_UFLOW_SHIFT		BIT(1)
+#define  SFC_ISR_TX_OFLOW_SHIFT		BIT(2)
+#define  SFC_ISR_TX_EMPTY_SHIFT		BIT(3)
+#define  SFC_ISR_TX_FINISH_SHIFT	BIT(4)
+#define  SFC_ISR_BUS_ERR_SHIFT		BIT(5)
+#define  SFC_ISR_NSPI_ERR_SHIFT		BIT(6)
+#define  SFC_ISR_DMA_SHIFT		BIT(7)
+
+/* FIFO status */
+#define SFC_FSR				0x20
+#define  SFC_FSR_TX_IS_FULL		BIT(0)
+#define  SFC_FSR_TX_IS_EMPTY		BIT(1)
+#define  SFC_FSR_RX_IS_EMPTY		BIT(2)
+#define  SFC_FSR_RX_IS_FULL		BIT(3)
+#define  SFC_FSR_TXLV_MASK		GENMASK(12, 8)
+#define  SFC_FSR_TXLV_SHIFT		8
+#define  SFC_FSR_RXLV_MASK		GENMASK(20, 16)
+#define  SFC_FSR_RXLV_SHIFT		16
+
+/* FSM status */
+#define SFC_SR				0x24
+#define  SFC_SR_IS_IDLE			0x0
+#define  SFC_SR_IS_BUSY			0x1
+
+/* Raw interrupt status */
+#define SFC_RISR			0x28
+#define  SFC_RISR_RX_FULL		BIT(0)
+#define  SFC_RISR_RX_UNDERFLOW		BIT(1)
+#define  SFC_RISR_TX_OVERFLOW		BIT(2)
+#define  SFC_RISR_TX_EMPTY		BIT(3)
+#define  SFC_RISR_TRAN_FINISH		BIT(4)
+#define  SFC_RISR_BUS_ERR		BIT(5)
+#define  SFC_RISR_NSPI_ERR		BIT(6)
+#define  SFC_RISR_DMA			BIT(7)
+
+/* Version */
+#define SFC_VER				0x2C
+#define  SFC_VER_3			0x3
+#define  SFC_VER_4			0x4
+#define  SFC_VER_5			0x5
+
+/* Master trigger */
+#define SFC_DMA_TRIGGER			0x80
+
+/* Src or Dst addr for master */
+#define SFC_DMA_ADDR			0x84
+
+/* Length control register extension 32GB */
+#define SFC_LEN_CTRL			0x88
+#define SFC_LEN_CTRL_TRB_SEL		1
+#define SFC_LEN_EXT			0x8C
+
+/* Command */
+#define SFC_CMD				0x100
+#define  SFC_CMD_IDX_SHIFT		0
+#define  SFC_CMD_DUMMY_SHIFT		8
+#define  SFC_CMD_DIR_SHIFT		12
+#define  SFC_CMD_DIR_RD			0
+#define  SFC_CMD_DIR_WR			1
+#define  SFC_CMD_ADDR_SHIFT		14
+#define  SFC_CMD_ADDR_0BITS		0
+#define  SFC_CMD_ADDR_24BITS		1
+#define  SFC_CMD_ADDR_32BITS		2
+#define  SFC_CMD_ADDR_XBITS		3
+#define  SFC_CMD_TRAN_BYTES_SHIFT	16
+#define  SFC_CMD_CS_SHIFT		30
+
+/* Address */
+#define SFC_ADDR			0x104
+
+/* Data */
+#define SFC_DATA			0x108
+
+/* The controller and documentation reports that it supports up to 4 CS
+ * devices (0-3), however I have only been able to test a single CS (CS 0)
+ * due to the configuration of my device.
+ */
+#define SFC_MAX_CHIPSELECT_NUM		4
+
+/* The SFC can transfer max 16KB - 1 at one time
+ * we set it to 15.5KB here for alignment.
+ */
+#define SFC_MAX_IOSIZE_VER3		(512 * 31)
+
+#define SFC_MAX_IOSIZE_VER4		(0xFFFFFFFF)
+
+/* DMA is only enabled for large data transmission */
+#define SFC_DMA_TRANS_THRETHOLD		(0x40)
+
+/* Maximum clock values from datasheet suggest keeping clock value under
+ * 150MHz. No minimum or average value is suggested, but the U-boot BSP driver
+ * has a minimum of 10MHz and a default of 80MHz which seems reasonable.
+ */
+#define SFC_MIN_SPEED_HZ		(10 * 1000 * 1000)
+#define SFC_DEFAULT_SPEED_HZ		(80 * 1000 * 1000)
+#define SFC_MAX_SPEED_HZ		(150 * 1000 * 1000)
+
+struct rockchip_sfc {
+	struct device *dev;
+	void __iomem *regbase;
+	struct clk *hclk;
+	struct clk *clk;
+	u32 frequency;
+	/* virtual mapped addr for dma_buffer */
+	void *buffer;
+	dma_addr_t dma_buffer;
+	struct completion cp;
+	bool use_dma;
+	u32 max_iosize;
+};
+
+static int rockchip_sfc_reset(struct rockchip_sfc *sfc)
+{
+	int err;
+	u32 status;
+
+	writel_relaxed(SFC_RCVR_RESET, sfc->regbase + SFC_RCVR);
+
+	err = readl_poll_timeout(sfc->regbase + SFC_RCVR, status,
+				 !(status & SFC_RCVR_RESET), 20,
+				 jiffies_to_usecs(HZ));
+	if (err)
+		dev_err(sfc->dev, "SFC reset never finished\n");
+
+	/* Still need to clear the masked interrupt from RISR */
+	writel_relaxed(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+
+	dev_dbg(sfc->dev, "reset\n");
+
+	return err;
+}
+
+static u16 rockchip_sfc_get_version(struct rockchip_sfc *sfc)
+{
+	return  (u16)(readl(sfc->regbase + SFC_VER) & 0xffff);
+}
+
+static u32 rockchip_sfc_get_max_iosize(struct rockchip_sfc *sfc)
+{
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
+		return SFC_MAX_IOSIZE_VER4;
+	else
+		return SFC_MAX_IOSIZE_VER3;
+}
+
+static int rockchip_sfc_init(struct rockchip_sfc *sfc)
+{
+	writel(0, sfc->regbase + SFC_CTRL);
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4)
+		writel(SFC_LEN_CTRL_TRB_SEL, sfc->regbase + SFC_LEN_CTRL);
+
+	return 0;
+}
+
+static inline int rockchip_sfc_get_fifo_level(struct rockchip_sfc *sfc, int wr)
+{
+	u32 fsr = readl_relaxed(sfc->regbase + SFC_FSR);
+	int level;
+
+	if (wr)
+		level = (fsr & SFC_FSR_TXLV_MASK) >> SFC_FSR_TXLV_SHIFT;
+	else
+		level = (fsr & SFC_FSR_RXLV_MASK) >> SFC_FSR_RXLV_SHIFT;
+
+	return level;
+}
+
+static int rockchip_sfc_wait_fifo_ready(struct rockchip_sfc *sfc, int wr, u32 timeout)
+{
+	unsigned long deadline = jiffies + timeout;
+	int level;
+
+	while (!(level = rockchip_sfc_get_fifo_level(sfc, wr))) {
+		if (time_after_eq(jiffies, deadline)) {
+			dev_warn(sfc->dev, "%s fifo timeout\n", wr ? "write" : "read");
+			return -ETIMEDOUT;
+		}
+		udelay(1);
+	}
+
+	return level;
+}
+
+static int rockchip_sfc_xfer_setup(struct rockchip_sfc *sfc,
+				   struct spi_mem *mem,
+				   const struct spi_mem_op *op,
+				   u32 len)
+{
+	u32 ctrl = 0, cmd = 0;
+
+	/* set CMD */
+	cmd = op->cmd.opcode;
+	ctrl |= ((op->cmd.buswidth >> 1) << SFC_CTRL_CMD_BITS_SHIFT);
+
+	/* set ADDR */
+	if (op->addr.nbytes) {
+		if (op->addr.nbytes == 4) {
+			cmd |= SFC_CMD_ADDR_32BITS << SFC_CMD_ADDR_SHIFT;
+		} else if (op->addr.nbytes == 3) {
+			cmd |= SFC_CMD_ADDR_24BITS << SFC_CMD_ADDR_SHIFT;
+		} else {
+			cmd |= SFC_CMD_ADDR_XBITS << SFC_CMD_ADDR_SHIFT;
+			writel_relaxed(op->addr.nbytes * 8 - 1, sfc->regbase + SFC_ABIT);
+		}
+
+		ctrl |= ((op->addr.buswidth >> 1) << SFC_CTRL_ADDR_BITS_SHIFT);
+	}
+
+	/* set DUMMY */
+	if (op->dummy.nbytes) {
+		if (op->dummy.buswidth == 4)
+			cmd |= op->dummy.nbytes * 2 << SFC_CMD_DUMMY_SHIFT;
+		else if (op->dummy.buswidth == 2)
+			cmd |= op->dummy.nbytes * 4 << SFC_CMD_DUMMY_SHIFT;
+		else
+			cmd |= op->dummy.nbytes * 8 << SFC_CMD_DUMMY_SHIFT;
Quoted 8 lines

drivers/spi/spi-rockchip-sfc.c line 290

Quoted 2 lines
drivers/spi/spi-rockchip-sfc.c new file +2 -0
+	}
+

I have no experience optimizing code or anything, but would it help here to read the output of rockchip_sfc_get_version() to a variable in the driver data, and then check that each time we hit this? I don't know if there is any real-world difference in reading a variable versus reading a register, so I'm just asking. It's not like the sfc_version will change once the device is probed. :-)

done.

Quoted 171 lines
Quoted 171 lines
drivers/spi/spi-rockchip-sfc.c new file +171 -0
+	/* set DATA */
+	if (rockchip_sfc_get_version(sfc) >= SFC_VER_4) /* Clear it if no data to transfer */
+		writel(len, sfc->regbase + SFC_LEN_EXT);
+	else
+		cmd |= len << SFC_CMD_TRAN_BYTES_SHIFT;
+	if (len) {
+		if (op->data.dir == SPI_MEM_DATA_OUT)
+			cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
+
+		ctrl |= ((op->data.buswidth >> 1) << SFC_CTRL_DATA_BITS_SHIFT);
+	}
+	if (!len && op->addr.nbytes)
+		cmd |= SFC_CMD_DIR_WR << SFC_CMD_DIR_SHIFT;
+
+	/* set the Controller */
+	ctrl |= SFC_CTRL_PHASE_SEL_NEGETIVE;
+	cmd |= mem->spi->chip_select << SFC_CMD_CS_SHIFT;
+
+	dev_dbg(sfc->dev, "addr.nbytes=%x(x%d) dummy.nbytes=%x(x%d)\n",
+		op->addr.nbytes, op->addr.buswidth,
+		op->dummy.nbytes, op->dummy.buswidth);
+	dev_dbg(sfc->dev, "ctrl=%x cmd=%x addr=%llx len=%x\n",
+		ctrl, cmd, op->addr.val, len);
+
+	writel(ctrl, sfc->regbase + SFC_CTRL);
+	writel(cmd, sfc->regbase + SFC_CMD);
+	if (op->addr.nbytes)
+		writel(op->addr.val, sfc->regbase + SFC_ADDR);
+
+	return 0;
+}
+
+static int rockchip_sfc_write_fifo(struct rockchip_sfc *sfc, const u8 *buf, int len)
+{
+	u8 bytes = len & 0x3;
+	u32 dwords;
+	int tx_level;
+	u32 write_words;
+	u32 tmp = 0;
+
+	dwords = len >> 2;
+	while (dwords) {
+		tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
+		if (tx_level < 0)
+			return tx_level;
+		write_words = min_t(u32, tx_level, dwords);
+		iowrite32_rep(sfc->regbase + SFC_DATA, buf, write_words);
+		buf += write_words << 2;
+		dwords -= write_words;
+	}
+
+	/* write the rest non word aligned bytes */
+	if (bytes) {
+		tx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_WR, HZ);
+		if (tx_level < 0)
+			return tx_level;
+		memcpy(&tmp, buf, bytes);
+		writel(tmp, sfc->regbase + SFC_DATA);
+	}
+
+	return len;
+}
+
+static int rockchip_sfc_read_fifo(struct rockchip_sfc *sfc, u8 *buf, int len)
+{
+	u8 bytes = len & 0x3;
+	u32 dwords;
+	u8 read_words;
+	int rx_level;
+	int tmp;
+
+	/* word aligned access only */
+	dwords = len >> 2;
+	while (dwords) {
+		rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
+		if (rx_level < 0)
+			return rx_level;
+		read_words = min_t(u32, rx_level, dwords);
+		ioread32_rep(sfc->regbase + SFC_DATA, buf, read_words);
+		buf += read_words << 2;
+		dwords -= read_words;
+	}
+
+	/* read the rest non word aligned bytes */
+	if (bytes) {
+		rx_level = rockchip_sfc_wait_fifo_ready(sfc, SFC_CMD_DIR_RD, HZ);
+		if (rx_level < 0)
+			return rx_level;
+		tmp = readl_relaxed(sfc->regbase + SFC_DATA);
+		memcpy(buf, &tmp, bytes);
+	}
+
+	return len;
+}
+
+static int rockchip_sfc_fifo_transfer_dma(struct rockchip_sfc *sfc, dma_addr_t dma_buf, size_t len)
+{
+	u32 reg;
+	int err = 0;
+
+	init_completion(&sfc->cp);
+
+	writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+
+	/* Enable transfer complete interrupt */
+	reg = readl(sfc->regbase + SFC_IMR);
+	reg &= ~SFC_IMR_DMA;
+	writel(reg, sfc->regbase + SFC_IMR);
+	writel((u32)dma_buf, sfc->regbase + SFC_DMA_ADDR);
+	writel(0x1, sfc->regbase + SFC_DMA_TRIGGER);
+
+	/* Wait for the interrupt. */
+	if (!wait_for_completion_timeout(&sfc->cp, msecs_to_jiffies(2000))) {
+		dev_err(sfc->dev, "DMA wait for transfer finish timeout\n");
+		err = -ETIMEDOUT;
+	}
+
+	writel(0xFFFFFFFF, sfc->regbase + SFC_ICLR);
+	/* Disable transfer finish interrupt */
+	reg = readl(sfc->regbase + SFC_IMR);
+	reg |= SFC_IMR_DMA;
+	writel(reg, sfc->regbase + SFC_IMR);
+
+	return len;
+}
+
+static int rockchip_sfc_xfer_data_poll(struct rockchip_sfc *sfc,
+				       const struct spi_mem_op *op, u32 len)
+{
+	dev_dbg(sfc->dev, "xfer_poll len=%x\n", len);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT)
+		return rockchip_sfc_write_fifo(sfc, op->data.buf.out, len);
+	else
+		return rockchip_sfc_read_fifo(sfc, op->data.buf.in, len);
+}
+
+static int rockchip_sfc_xfer_data_dma(struct rockchip_sfc *sfc,
+				      const struct spi_mem_op *op, u32 len)
+{
+	int ret;
+
+	dev_dbg(sfc->dev, "xfer_dma len=%x\n", len);
+
+	if (op->data.dir == SPI_MEM_DATA_OUT) {
+		memcpy_toio(sfc->buffer, op->data.buf.out, len);
+		ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
+	} else {
+		ret = rockchip_sfc_fifo_transfer_dma(sfc, sfc->dma_buffer, len);
+		memcpy_fromio(op->data.buf.in, sfc->buffer, len);
+	}
+
+	return ret;
+}
+
+static int rockchip_sfc_xfer_done(struct rockchip_sfc *sfc, u32 timeout_us)
+{
+	int ret = 0;
+	u32 status;
+
+	ret = readl_poll_timeout(sfc->regbase + SFC_SR, status,
+				 !(status & SFC_SR_IS_BUSY),
+				 20, timeout_us);
+	if (ret) {
+		dev_err(sfc->dev, "wait sfc idle timeout\n");
+		rockchip_sfc_reset(sfc);
+
+		ret = -EIO;
+	}
+
+	return ret;
Quoted 8 lines

drivers/spi/spi-rockchip-sfc.c line 467

Quoted 6 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+}
+
+static int rockchip_sfc_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);
+	u32 len = min_t(u32, op->data.nbytes, sfc->max_iosize);

Is it necessary to use the minimum of these 2 values if we use an adjust_op_size which I propose below?

it necessary if use adjust_op_size, done.

Quoted 13 lines

drivers/spi/spi-rockchip-sfc.c line 469

Quoted 2 lines
drivers/spi/spi-rockchip-sfc.c new file +2 -0
+	int ret;
+

Again I'm asking this as someone with no experience optimizing code or with compilers, but would it help to add an unlikely() here? It's all but guaranteed the first time this code path is called the clock will need to be set, but each subsequent call should not really have to care since the clock likely won't be changing (as long as we're on the same CS). We can also then set the sfc->frequency to what the max_speed_hz was after successfully setting the rate so we can hit the faster path after the first run (it looks like it's checking the uninitalized value but never updating it after it's changed, so it's always doing the clk_set_rate()).

Quoted 1 line

Also, should we clamp the clock speed between the min and max values?

done.

Quoted 38 lines
Quoted 14 lines
drivers/spi/spi-rockchip-sfc.c new file +14 -0
+	if (mem->spi->max_speed_hz != sfc->frequency) {
+		if (clk_set_rate(sfc->clk, mem->spi->max_speed_hz))
+			return ret;
+		dev_dbg(sfc->dev, "set_freq=%dHz real_freq=%ldHz\n",
+			sfc->frequency, clk_get_rate(sfc->clk));
+	}
+
+	rockchip_sfc_xfer_setup(sfc, mem, op, len);
+	if (len) {
+		if (likely(sfc->use_dma) && !(len & 0x3) && len >= SFC_DMA_TRANS_THRETHOLD)
+			ret = rockchip_sfc_xfer_data_dma(sfc, op, len);
+		else
+			ret = rockchip_sfc_xfer_data_poll(sfc, op, len);
+

drivers/spi/spi-rockchip-sfc.c line 493

Quoted 10 lines
drivers/spi/spi-rockchip-sfc.c new file +10 -0
+		if (ret != len) {
+			dev_err(sfc->dev, "xfer data failed ret %d dir %d\n", ret, op->data.dir);
+
+			return -EIO;
+		}
+	}
+
+	return rockchip_sfc_xfer_done(sfc, 100000);
+}
+

I'll be honest with you, I had no idea if I needed this function or not (the rockchip_sfc_get_name() function). I'm pretty sure it's not needed though, so I assume it can be safely removed.

drivers/spi/spi-rockchip-sfc.c line 499

Quoted 6 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+static const char *rockchip_sfc_get_name(struct spi_mem *mem)
+{
+	return devm_kasprintf(&mem->spi->dev, GFP_KERNEL, "%s.%d",
+			      dev_name(&mem->spi->dev), mem->spi->chip_select);
+}
+

I had an issue with doing dd as mentioned above reading against mtd0, and was able to fix it by adding a mem_op of adjust_op_size like this. Not sure if it works for the v4/v5 hardware though.

Quoted 7 lines

static int rockchip_sfc_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)

{
	struct rockchip_sfc *sfc = spi_master_get_devdata(mem->spi->master);

	op->data.nbytes = min(op->data.nbytes, sfc->max_iosize);
	return 0;
}

good idea.

Quoted 12 lines
Quoted 12 lines
drivers/spi/spi-rockchip-sfc.c new file +12 -0
+static const struct spi_controller_mem_ops rockchip_sfc_mem_ops = {
+	.exec_op = rockchip_sfc_exec_mem_op,
+	.get_name = rockchip_sfc_get_name,
+};
+
+static irqreturn_t rockchip_sfc_irq_handler(int irq, void *dev_id)
+{
+	struct rockchip_sfc *sfc = dev_id;
+	u32 reg;
+
+	reg = readl(sfc->regbase + SFC_RISR);
+
Quoted 9 lines
Quoted 7 lines
drivers/spi/spi-rockchip-sfc.c new file +6 -0
+	/* Clear interrupt */
+	writel_relaxed(reg, sfc->regbase + SFC_ICLR);
+
+	if (reg & SFC_RISR_DMA)
+		complete(&sfc->cp);
+

From a previous comment, we should only clear the interrupt if we

handle the specific one in question.

Compare with drivers/spi/spi-cadence-quadspi.c, I think the former code work well. Can explain more for the reason.

Quoted 137 lines
Quoted 137 lines
drivers/spi/spi-rockchip-sfc.c new file +137 -0
+	return IRQ_HANDLED;
+}
+
+static int rockchip_sfc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct spi_master *master;
+	struct resource *res;
+	struct rockchip_sfc *sfc;
+	int ret;
+
+	master = devm_spi_alloc_master(&pdev->dev, sizeof(*sfc));
+	if (!master)
+		return -ENOMEM;
+
+	master->mem_ops = &rockchip_sfc_mem_ops;
+	master->dev.of_node = pdev->dev.of_node;
+	master->mode_bits = SPI_TX_QUAD | SPI_TX_DUAL | SPI_RX_QUAD | SPI_RX_DUAL;
+	master->min_speed_hz = SFC_MIN_SPEED_HZ;
+	master->max_speed_hz = SFC_MAX_SPEED_HZ;
+	master->num_chipselect = SFC_MAX_CHIPSELECT_NUM;
+
+	sfc = spi_master_get_devdata(master);
+	sfc->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	sfc->regbase = devm_ioremap_resource(dev, res);
+	if (IS_ERR(sfc->regbase))
+		return PTR_ERR(sfc->regbase);
+
+	sfc->clk = devm_clk_get(&pdev->dev, "clk_sfc");
+	if (IS_ERR(sfc->clk)) {
+		dev_err(&pdev->dev, "Failed to get sfc interface clk\n");
+		return PTR_ERR(sfc->clk);
+	}
+
+	sfc->hclk = devm_clk_get(&pdev->dev, "hclk_sfc");
+	if (IS_ERR(sfc->hclk)) {
+		dev_err(&pdev->dev, "Failed to get sfc ahb clk\n");
+		return PTR_ERR(sfc->hclk);
+	}
+
+	sfc->use_dma = !of_property_read_bool(sfc->dev->of_node,
+					      "rockchip,sfc-no-dma");
+
+	if (sfc->use_dma) {
+		ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+		if (ret) {
+			dev_warn(dev, "Unable to set dma mask\n");
+			return ret;
+		}
+
+		sfc->buffer = dmam_alloc_coherent(dev, SFC_MAX_IOSIZE_VER3,
+						  &sfc->dma_buffer,
+						  GFP_KERNEL);
+		if (!sfc->buffer)
+			return -ENOMEM;
+	}
+
+	ret = clk_prepare_enable(sfc->hclk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to enable ahb clk\n");
+		goto err_hclk;
+	}
+
+	ret = clk_prepare_enable(sfc->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to enable interface clk\n");
+		goto err_clk;
+	}
+
+	/* Find the irq */
+	ret = platform_get_irq(pdev, 0);
+	if (ret < 0) {
+		dev_err(dev, "Failed to get the irq\n");
+		goto err_irq;
+	}
+
+	ret = devm_request_irq(dev, ret, rockchip_sfc_irq_handler,
+			       0, pdev->name, sfc);
+	if (ret) {
+		dev_err(dev, "Failed to request irq\n");
+
+		return ret;
+	}
+
+	ret = rockchip_sfc_init(sfc);
+	if (ret)
+		goto err_irq;
+
+	sfc->max_iosize = rockchip_sfc_get_max_iosize(sfc);
+
+	ret = spi_register_master(master);
+	if (ret)
+		goto err_irq;
+
+	return 0;
+
+err_irq:
+	clk_disable_unprepare(sfc->clk);
+err_clk:
+	clk_disable_unprepare(sfc->hclk);
+err_hclk:
+	return ret;
+}
+
+static int rockchip_sfc_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct rockchip_sfc *sfc = platform_get_drvdata(pdev);
+
+	spi_unregister_master(master);
+
+	clk_disable_unprepare(sfc->clk);
+	clk_disable_unprepare(sfc->hclk);
+
+	return 0;
+}
+
+static const struct of_device_id rockchip_sfc_dt_ids[] = {
+	{ .compatible = "rockchip,px30-sfc"},
+	{ .compatible = "rockchip,rk3036-sfc"},
+	{ .compatible = "rockchip,rk3308-sfc"},
+	{ .compatible = "rockchip,rv1126-sfc"},
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rockchip_sfc_dt_ids);
+
+static struct platform_driver rockchip_sfc_driver = {
+	.driver = {
+		.name	= "rockchip-sfc",
+		.of_match_table = rockchip_sfc_dt_ids,
+	},
+	.probe	= rockchip_sfc_probe,
+	.remove	= rockchip_sfc_remove,
+};
+module_platform_driver(rockchip_sfc_driver);
Quoted 8 lines

drivers/spi/spi-rockchip-sfc.c line 659

Quoted 5 lines
drivers/spi/spi-rockchip-sfc.c new file +5 -0
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("Rockchip Serial Flash Controller Driver");
+MODULE_AUTHOR("Shawn Lin <[email protected]>");
+MODULE_AUTHOR("Chris Morgan <[email protected]>");

I know folks will hate on me for this (and for good reason given it messes up IDs and stuff), but I prefer [email protected] if my email is in here, as that's the one I've been using for decades...

ok.

Quoted 8 lines
Quoted 6 lines

+MODULE_AUTHOR("Jon Lin <[email protected]>");

Signature · 1 line
2.17.1
author
#10 lore raw

PATCH v6 3/8 arm64: dts: rockchip: Add SFC to PX30

In reply to Jon Lin

From: Chris Morgan <[email protected]>

Add a devicetree entry for the Rockchip SFC for the PX30 SOC.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 arch/arm64/boot/dts/rockchip/px30.dtsi | 38 ++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)
arch/arm64/boot/dts/rockchip/px30.dtsi +38 -0
index 09baa8a167ce..99a46259e428 100644
@@ -966,6 +966,18 @@
 		status = "disabled";
 	};
 
+	sfc: spi@ff3a0000 {
+		compatible = "rockchip,px30-sfc","rockchip,rk3036-sfc";
+		reg = <0x0 0xff3a0000 0x0 0x4000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SFC>, <&cru SCLK_SFC>;
+		clock-names = "hclk_sfc", "clk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		power-domains = <&power PX30_PD_MMC_NAND>;
+		status = "disabled";
+	};
+
 	nfc: nand-controller@ff3b0000 {
 		compatible = "rockchip,px30-nfc";
 		reg = <0x0 0xff3b0000 0x0 0x4000>;
@@ -1967,6 +1979,32 @@
 			};
 		};
 
+		serial_flash {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<1 RK_PA0 3 &pcfg_pull_none>,
+					<1 RK_PA1 3 &pcfg_pull_none>,
+					<1 RK_PA2 3 &pcfg_pull_none>,
+					<1 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<1 RK_PA0 3 &pcfg_pull_none>,
+					<1 RK_PA1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<1 RK_PA4 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<1 RK_PB1 3 &pcfg_pull_none>;
+			};
+		};
+
 		lcdc {
 			lcdc_rgb_dclk_pin: lcdc-rgb-dclk-pin {
 				rockchip,pins =
Signature · 1 line
2.17.1
author
#11 lore raw

PATCH v6 4/8 clk: rockchip: Add support for hclk_sfc on rk3036

In reply to Jon Lin

From: Chris Morgan <[email protected]>

Add support for the bus clock for the serial flash controller on the rk3036. Taken from the Rockchip BSP kernel but not tested on real hardware (as I lack a 3036 based SoC to test).

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 drivers/clk/rockchip/clk-rk3036.c      | 2 +-
 include/dt-bindings/clock/rk3036-cru.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3036.c +1 -1
index 91d56ad45817..ebb628733f6d 100644
@@ -403,7 +403,7 @@ static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = {
 	GATE(HCLK_OTG0, "hclk_otg0", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 13, GFLAGS),
 	GATE(HCLK_OTG1, "hclk_otg1", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(7), 3, GFLAGS),
 	GATE(HCLK_I2S, "hclk_i2s", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS),
-	GATE(0, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),
+	GATE(HCLK_SFC, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),
 	GATE(HCLK_MAC, "hclk_mac", "hclk_peri", 0, RK2928_CLKGATE_CON(3), 5, GFLAGS),
 
 	/* pclk_peri gates */
include/dt-bindings/clock/rk3036-cru.h +1 -0
index 35a5a01f9697..a96a9870ad59 100644
@@ -81,6 +81,7 @@
 #define HCLK_OTG0		449
 #define HCLK_OTG1		450
 #define HCLK_NANDC		453
+#define HCLK_SFC		454
 #define HCLK_SDMMC		456
 #define HCLK_SDIO		457
 #define HCLK_EMMC		459
Signature · 1 line
2.17.1
#12 lore raw

Re: [PATCH v6 4/8] clk: rockchip: Add support for hclk_sfc on rk3036

Hi Jon,

For rk3036 we might need another fix added to this serie as well.

clk: rockchip: rk3036: fix up the sclk_sfc parent error
https://github.com/rockchip-linux/kernel/commit/100718ef0d44872db1672b6a88030374c0d1613b

===
Add more people for clk driver changes:

M: Michael Turquette <[email protected]>
M: Stephen Boyd <[email protected]>
L: [email protected]

===

Johan

Quoted 1 line · Jon Lin

From: Chris Morgan <[email protected]>

From: Randy Li <[email protected]>

Quoted 5 lines

Add support for the bus clock for the serial flash controller on the rk3036. Taken from the Rockchip BSP kernel but not tested on real hardware (as I lack a 3036 based SoC to test).

Maybe give credit to the original author?
clk: rockchip: rk3036: export the sfc clocks
https://github.com/rockchip-linux/kernel/commit/600925e8ef6edbdda0a4ac6b3c55b0199be1e03e

Quoted 20 lines

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 drivers/clk/rockchip/clk-rk3036.c      | 2 +-
 include/dt-bindings/clock/rk3036-cru.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3036.c +0 -0
index 91d56ad45817..ebb628733f6d 100644

drivers/clk/rockchip/clk-rk3036.c static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = { · line 407

Quoted 6 lines
drivers/clk/rockchip/clk-rk3036.c +1 -1
@@ -403,7 +403,7 @@ static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = {
 	GATE(HCLK_OTG0, "hclk_otg0", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 13, GFLAGS),
 	GATE(HCLK_OTG1, "hclk_otg1", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(7), 3, GFLAGS),
 	GATE(HCLK_I2S, "hclk_i2s", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS),
 
-	GATE(0, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),
+	GATE(HCLK_SFC, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),

Maybe CLK_IGNORE_UNUSED should be changed to 0 ?

Quoted 16 lines
drivers/clk/rockchip/clk-rk3036.c +0 -0
 	GATE(HCLK_MAC, "hclk_mac", "hclk_peri", 0, RK2928_CLKGATE_CON(3), 5, GFLAGS),
 
drivers/clk/rockchip/clk-rk3036.c +0 -0
 	/* pclk_peri gates */
include/dt-bindings/clock/rk3036-cru.h +1 -0
index 35a5a01f9697..a96a9870ad59 100644
@@ -81,6 +81,7 @@
 #define HCLK_OTG0		449
 #define HCLK_OTG1		450
 #define HCLK_NANDC		453
+#define HCLK_SFC		454
 #define HCLK_SDMMC		456
 #define HCLK_SDIO		457
 #define HCLK_EMMC		459
author
#13 lore raw

Re: [PATCH v6 4/8] clk: rockchip: Add support for hclk_sfc on rk3036

Quoted 27 lines · Johan Jonker

Hi Jon,

For rk3036 we might need another fix added to this serie as well.

clk: rockchip: rk3036: fix up the sclk_sfc parent error
https://github.com/rockchip-linux/kernel/commit/100718ef0d44872db1672b6a88030374c0d1613b

===
Add more people for clk driver changes:

M: Michael Turquette <[email protected]>
M: Stephen Boyd <[email protected]>
L: [email protected]

===

Johan

Quoted 1 line · Jon Lin

From: Chris Morgan <[email protected]>

From: Randy Li <[email protected]>

Quoted 4 lines

Add support for the bus clock for the serial flash controller on the rk3036. Taken from the Rockchip BSP kernel but not tested on real hardware (as I lack a 3036 based SoC to test).

Quoted 5 lines

Maybe give credit to the original author?
clk: rockchip: rk3036: export the sfc clocks
https://github.com/rockchip-linux/kernel/commit/600925e8ef6edbdda0a4ac6b3c55b0199be1e03e

something wrong when I add [email protected] email, I will make a confirmation with it with him.

Quoted 45 lines
Quoted 20 lines

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

  drivers/clk/rockchip/clk-rk3036.c      | 2 +-
  include/dt-bindings/clock/rk3036-cru.h | 1 +
  2 files changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3036.c +0 -0
index 91d56ad45817..ebb628733f6d 100644

drivers/clk/rockchip/clk-rk3036.c static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = { · line 406

Quoted 5 lines
drivers/clk/rockchip/clk-rk3036.c +1 -1
@@ -403,7 +403,7 @@ static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = {
  	GATE(HCLK_OTG0, "hclk_otg0", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 13, GFLAGS),
  	GATE(HCLK_OTG1, "hclk_otg1", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(7), 3, GFLAGS),
  	GATE(HCLK_I2S, "hclk_i2s", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS),
-	GATE(0, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),
+	GATE(HCLK_SFC, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),

Maybe CLK_IGNORE_UNUSED should be changed to 0 ?

Quoted 16 lines
drivers/clk/rockchip/clk-rk3036.c +0 -0
  	GATE(HCLK_MAC, "hclk_mac", "hclk_peri", 0, RK2928_CLKGATE_CON(3), 5, GFLAGS),
 
  	/* pclk_peri gates */
include/dt-bindings/clock/rk3036-cru.h +1 -0
index 35a5a01f9697..a96a9870ad59 100644
@@ -81,6 +81,7 @@
  #define HCLK_OTG0		449
  #define HCLK_OTG1		450
  #define HCLK_NANDC		453
+#define HCLK_SFC		454
  #define HCLK_SDMMC		456
  #define HCLK_SDIO		457
  #define HCLK_EMMC		459
author
#14 lore raw

Re: [PATCH v6 4/8] clk: rockchip: Add support for hclk_sfc on rk3036

In reply to Johan Jonker
Quoted 27 lines · Johan Jonker

Hi Jon,

For rk3036 we might need another fix added to this serie as well.

clk: rockchip: rk3036: fix up the sclk_sfc parent error
https://github.com/rockchip-linux/kernel/commit/100718ef0d44872db1672b6a88030374c0d1613b

===
Add more people for clk driver changes:

M: Michael Turquette <[email protected]>
M: Stephen Boyd <[email protected]>
L: [email protected]

===

Johan

Quoted 1 line · Jon Lin

From: Chris Morgan <[email protected]>

From: Randy Li <[email protected]>

Quoted 4 lines

Add support for the bus clock for the serial flash controller on the rk3036. Taken from the Rockchip BSP kernel but not tested on real hardware (as I lack a 3036 based SoC to test).

Quoted 5 lines

Maybe give credit to the original author?
clk: rockchip: rk3036: export the sfc clocks
https://github.com/rockchip-linux/kernel/commit/600925e8ef6edbdda0a4ac6b3c55b0199be1e03e

Randy Li has resigned from RK

Quoted 45 lines
Quoted 20 lines

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

  drivers/clk/rockchip/clk-rk3036.c      | 2 +-
  include/dt-bindings/clock/rk3036-cru.h | 1 +
  2 files changed, 2 insertions(+), 1 deletion(-)
drivers/clk/rockchip/clk-rk3036.c +0 -0
index 91d56ad45817..ebb628733f6d 100644

drivers/clk/rockchip/clk-rk3036.c static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = { · line 406

Quoted 5 lines
drivers/clk/rockchip/clk-rk3036.c +1 -1
@@ -403,7 +403,7 @@ static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = {
  	GATE(HCLK_OTG0, "hclk_otg0", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 13, GFLAGS),
  	GATE(HCLK_OTG1, "hclk_otg1", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(7), 3, GFLAGS),
  	GATE(HCLK_I2S, "hclk_i2s", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS),
-	GATE(0, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),
+	GATE(HCLK_SFC, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS),

Maybe CLK_IGNORE_UNUSED should be changed to 0 ?

Quoted 16 lines
drivers/clk/rockchip/clk-rk3036.c +0 -0
  	GATE(HCLK_MAC, "hclk_mac", "hclk_peri", 0, RK2928_CLKGATE_CON(3), 5, GFLAGS),
 
  	/* pclk_peri gates */
include/dt-bindings/clock/rk3036-cru.h +1 -0
index 35a5a01f9697..a96a9870ad59 100644
@@ -81,6 +81,7 @@
  #define HCLK_OTG0		449
  #define HCLK_OTG1		450
  #define HCLK_NANDC		453
+#define HCLK_SFC		454
  #define HCLK_SDMMC		456
  #define HCLK_SDIO		457
  #define HCLK_EMMC		459
author
#15 lore raw

PATCH v6 5/8 arm: dts: rockchip: Add SFC to RK3036

In reply to Jon Lin

From: Chris Morgan <[email protected]>

Add a devicetree entry for the Rockchip SFC for the RK3036 SOC.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 arch/arm/boot/dts/rk3036.dtsi | 42 +++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/arm/boot/dts/rk3036.dtsi +42 -0
index e24230d50a78..e7faf815ca74 100644
@@ -206,6 +206,17 @@
 		status = "disabled";
 	};
 
+	sfc: spi@10208000 {
+		compatible = "rockchip,rk3036-sfc";
+		reg = <0x10208000 0x4000>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SFC>, <&cru SCLK_SFC>;
+		clock-names = "hclk_sfc", "clk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	sdmmc: mmc@10214000 {
 		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x10214000 0x4000>;
@@ -684,6 +695,37 @@
 			};
 		};
 
+		serial_flash {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<1 RK_PD0 3 &pcfg_pull_none>,
+					<1 RK_PD1 3 &pcfg_pull_none>,
+					<1 RK_PD2 3 &pcfg_pull_none>,
+					<1 RK_PD3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<1 RK_PD0 3 &pcfg_pull_none>,
+					<1 RK_PD1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<2 RK_PA2 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs1: sfc-cs1 {
+				rockchip,pins =
+					<2 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<2 RK_PA4 3 &pcfg_pull_none>;
+			};
+		};
+
 		emac {
 			emac_xfer: emac-xfer {
 				rockchip,pins = <2 RK_PB2 1 &pcfg_pull_default>, /* crs_dvalid */
Signature · 1 line
2.17.1
author
#16 lore raw

PATCH v6 6/8 arm: dts: rockchip: Add SFC to RV1108

From: Chris Morgan <[email protected]>

Add a devicetree entry for the Rockchip SFC for the RV1108 SOC.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 arch/arm/boot/dts/rv1108.dtsi | 37 +++++++++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)
arch/arm/boot/dts/rv1108.dtsi +37 -0
index 884872ca5207..c2b6adabb263 100644
@@ -536,6 +536,17 @@
 		status = "disabled";
 	};
 
+	sfc: spi@301c0000 {
+		compatible = "rockchip,rv1108-sfc", "rockchip,rk3036-sfc";
+		reg = <0x301c0000 0x4000>;
+		interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SFC>, <&cru SCLK_SFC>;
+		clock-names = "hclk_sfc", "clk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	gmac: eth@30200000 {
 		compatible = "rockchip,rv1108-gmac";
 		reg = <0x30200000 0x10000>;
@@ -704,6 +715,32 @@
 			};
 		};
 
+		serial_flash {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<2 RK_PA0 3 &pcfg_pull_none>,
+					<2 RK_PA1 3 &pcfg_pull_none>,
+					<2 RK_PA2 3 &pcfg_pull_none>,
+					<2 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<2 RK_PA0 3 &pcfg_pull_none>,
+					<2 RK_PA1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<2 RK_PB4 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<2 RK_PB7 2 &pcfg_pull_none>;
+			};
+		};
+
 		gmac {
 			rmii_pins: rmii-pins {
 				rockchip,pins =	<1 RK_PC5 2 &pcfg_pull_none>,
Signature · 1 line
2.17.1
author
#17 lore raw

PATCH v6 7/8 arm64: dts: rockchip: Add SFC to RK3308

In reply to Jon Lin

From: Chris Morgan <[email protected]>

Add a devicetree entry for the Rockchip SFC for the RK3308 SOC.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 arch/arm64/boot/dts/rockchip/rk3308.dtsi | 37 ++++++++++++++++++++++++
 1 file changed, 37 insertions(+)
arch/arm64/boot/dts/rockchip/rk3308.dtsi +37 -0
index 0c5fa9801e6f..f40feb08f3cf 100644
@@ -637,6 +637,17 @@
 		status = "disabled";
 	};
 
+	sfc: spi@ff4c0000 {
+		compatible = "rockchip,rk3308-sfc", "rockchip,rk3036-sfc";
+		reg = <0x0 0xff4c0000 0x0 0x4000>;
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SFC>, <&cru SCLK_SFC>;
+		clock-names = "hclk_sfc", "clk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	cru: clock-controller@ff500000 {
 		compatible = "rockchip,rk3308-cru";
 		reg = <0x0 0xff500000 0x0 0x1000>;
@@ -910,6 +921,32 @@
 			};
 		};
 
+		serial_flash {
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
+					<3 RK_PA0 3 &pcfg_pull_none>,
+					<3 RK_PA1 3 &pcfg_pull_none>,
+					<3 RK_PA2 3 &pcfg_pull_none>,
+					<3 RK_PA3 3 &pcfg_pull_none>;
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
+					<3 RK_PA0 3 &pcfg_pull_none>,
+					<3 RK_PA1 3 &pcfg_pull_none>;
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
+					<3 RK_PA4 3 &pcfg_pull_none>;
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
+					<3 RK_PA5 3 &pcfg_pull_none>;
+			};
+		};
+
 		gmac {
 			rmii_pins: rmii-pins {
 				rockchip,pins =
Signature · 1 line
2.17.1
author
#18 lore raw

PATCH v6 8/8 arm64: dts: rockchip: Enable SFC for Odroid Go Advance

In reply to Jon Lin

From: Chris Morgan <[email protected]>

This enables the Rockchip Serial Flash Controller for the Odroid Go Advance. Note that while the attached SPI NOR flash and the controller both support quad read mode, only 2 of the required 4 pins are present. The rx and tx bus width is set to 2 for this reason.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 .../boot/dts/rockchip/rk3326-odroid-go2.dts      | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts +16 -0
index 49c97f76df77..f78e11dd8447 100644
@@ -484,6 +484,22 @@
 	status = "okay";
 };
 
+&sfc {
+	pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus2>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <108000000>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+	};
+};
+
 &tsadc {
 	status = "okay";
 };
Signature · 1 line
2.17.1
#19 lore raw

Re: [PATCH v6 5/8] arm: dts: rockchip: Add SFC to RK3036

In reply to Jon Lin
Quoted 41 lines · Jon Lin

From: Chris Morgan <[email protected]>

Add a devicetree entry for the Rockchip SFC for the RK3036 SOC.

---

Changes in v6: None
Changes in v5: None
Changes in v4: None
Changes in v3: None
Changes in v2: None
Changes in v1: None

 arch/arm/boot/dts/rk3036.dtsi | 42 +++++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)
arch/arm/boot/dts/rk3036.dtsi +11 -0
index e24230d50a78..e7faf815ca74 100644
@@ -206,6 +206,17 @@
 		status = "disabled";
 	};
 
+	sfc: spi@10208000 {
+		compatible = "rockchip,rk3036-sfc";
+		reg = <0x10208000 0x4000>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_SFC>, <&cru SCLK_SFC>;
+		clock-names = "hclk_sfc", "clk_sfc";
+		pinctrl-0 = <&sfc_clk &sfc_cs0 &sfc_bus4>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	sdmmc: mmc@10214000 {
 		compatible = "rockchip,rk3036-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x10214000 0x4000>;

arch/arm/boot/dts/rk3036.dtsi line 699

Quoted 5 lines
arch/arm/boot/dts/rk3036.dtsi +1 -0
@@ -684,6 +695,37 @@
 			};
 		};
 
 
+		serial_flash {

sfc {

Nodes are sort alphabetically.
Sort other patches with sfc nodes in this serie as well. Maybe rename nodename consistent with sfc label? Similar to nfc nodes?

arch/arm/boot/dts/rk3036.dtsi line 704

Quoted 7 lines
arch/arm/boot/dts/rk3036.dtsi +6 -0
+			sfc_bus4: sfc-bus4 {
+				rockchip,pins =
 
+					<1 RK_PD0 3 &pcfg_pull_none>,
+					<1 RK_PD1 3 &pcfg_pull_none>,
+					<1 RK_PD2 3 &pcfg_pull_none>,
+					<1 RK_PD3 3 &pcfg_pull_none>;

Keep align with the rest in the pinctrl node. Check that in other sfc patches as well.

arch/arm/boot/dts/rk3036.dtsi line 710

Quoted 7 lines
arch/arm/boot/dts/rk3036.dtsi +6 -0
+			};
+
+			sfc_bus2: sfc-bus2 {
+				rockchip,pins =
 
+					<1 RK_PD0 3 &pcfg_pull_none>,
+					<1 RK_PD1 3 &pcfg_pull_none>;

dito

arch/arm/boot/dts/rk3036.dtsi line 715

Quoted 6 lines
arch/arm/boot/dts/rk3036.dtsi +5 -0
+			};
+
+			sfc_cs0: sfc-cs0 {
+				rockchip,pins =
 
+					<2 RK_PA2 3 &pcfg_pull_none>;

dito

arch/arm/boot/dts/rk3036.dtsi line 720

Quoted 6 lines
arch/arm/boot/dts/rk3036.dtsi +5 -0
+			};
+
+			sfc_cs1: sfc-cs1 {
+				rockchip,pins =
 
+					<2 RK_PA3 3 &pcfg_pull_none>;

dito

arch/arm/boot/dts/rk3036.dtsi line 725

Quoted 6 lines
arch/arm/boot/dts/rk3036.dtsi +5 -0
+			};
+
+			sfc_clk: sfc-clk {
+				rockchip,pins =
 
+					<2 RK_PA4 3 &pcfg_pull_none>;

dito

arch/arm/boot/dts/rk3036.dtsi line 731

Quoted 7 lines
arch/arm/boot/dts/rk3036.dtsi +3 -0
+			};
+		};
+
 		emac {
 			emac_xfer: emac-xfer {
 				rockchip,pins = <2 RK_PB2 1 &pcfg_pull_default>, /* crs_dvalid */

_______________________________________________
Linux-rockchip mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-rockchip