ARM: dts: imxrt1050-evk: move all u-boot, dm-spl to imxrt1050-evk-u-boot.dtsi file
Subsystems (2)
PATCH 1/3 ARM: dts: imxrt1050-evk: move all u-boot, dm-spl to imxrt1050-evk-u-boot.dtsi file
At the moment a lot of u-boot,dm-spl properties are present in board .dts file but this is not correct since u-boot,dm-spl property is u-boot specific and must be listed into the separate imrt1050-evk-u-boot.dtsi file. So let's move every u-boot,dm-spl property present in imxrt1050-evk.dts to imxrt1050-evk-u-boot.dtsi file.
--- arch/arm/dts/imxrt1050-evk-u-boot.dtsi | 38 ++++++++++++++++++++++++++ arch/arm/dts/imxrt1050.dtsi | 13 --------- 2 files changed, 38 insertions(+), 13 deletions(-)
arch/arm/dts/imxrt1050-evk-u-boot.dtsi +38 -0
@@ -8,6 +8,42 @@ chosen { u-boot,dm-spl; }; + + clocks { + u-boot,dm-spl; + }; + + soc { + u-boot,dm-spl; + }; +}; + +&osc { + u-boot,dm-spl; +}; + +&clks { + u-boot,dm-spl; +}; + +&gpio1 { + u-boot,dm-spl; +}; + +&gpio2 { + u-boot,dm-spl; +}; + +&gpio3 { + u-boot,dm-spl; +}; + +&gpio4 { + u-boot,dm-spl; +}; + +&gpio5 { + u-boot,dm-spl; }; &gpt1 {
@@ -19,6 +55,8 @@ }; &semc { + u-boot,dm-spl; + bank1: bank at 0 { u-boot,dm-spl; };
arch/arm/dts/imxrt1050.dtsi +0 -13
@@ -27,10 +27,7 @@ }; clocks { - u-boot,dm-spl; - osc: osc { - u-boot,dm-spl; compatible = "fsl,imx-osc", "fixed-clock"; #clock-cells = <0>; clock-frequency = <24000000>;
@@ -38,10 +35,7 @@ }; soc { - u-boot,dm-spl; - semc: semc at 402f0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-semc"; reg = <0x402f0000 0x4000>; clocks = <&clks IMXRT1050_CLK_SEMC>;
@@ -66,7 +60,6 @@ }; clks: ccm at 400fc000 { - u-boot,dm-spl; compatible = "fsl,imxrt1050-ccm"; reg = <0x400fc000 0x4000>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
@@ -75,7 +68,6 @@ }; usdhc1: usdhc at 402c0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-usdhc"; reg = <0x402c0000 0x10000>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -88,7 +80,6 @@ }; gpio1: gpio at 401b8000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401b8000 0x4000>; interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
@@ -100,7 +91,6 @@ }; gpio2: gpio at 401bc000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401bc000 0x4000>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
@@ -112,7 +102,6 @@ }; gpio3: gpio at 401c0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401c0000 0x4000>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
@@ -124,7 +113,6 @@ }; gpio4: gpio at 401c4000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401c4000 0x4000>; interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
@@ -136,7 +124,6 @@ }; gpio5: gpio at 400c0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x400c0000 0x4000>; interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
Signature · 1 line
2.25.1
PATCH 2/3 ARM: dts: imxrt1020-evk: move all u-boot, dm-spl to imxrt1020-evk-u-boot.dtsi file
At the moment a lot of u-boot,dm-spl properties are present in board .dts file but this is not correct since u-boot,dm-spl property is u-boot specific and must be listed into the separate imrt1020-evk-u-boot.dtsi file. So let's move every u-boot,dm-spl property present in imxrt1020-evk.dts to imxrt1020-evk-u-boot.dtsi file.
--- arch/arm/dts/imxrt1020-evk-u-boot.dtsi | 34 ++++++++++++++++++++++++++ arch/arm/dts/imxrt1020.dtsi | 10 -------- 2 files changed, 34 insertions(+), 10 deletions(-)
arch/arm/dts/imxrt1020-evk-u-boot.dtsi +34 -0
@@ -8,6 +8,38 @@ chosen { u-boot,dm-spl; }; + + clocks { + u-boot,dm-spl; + }; + + soc { + u-boot,dm-spl; + }; +}; + +&osc { + u-boot,dm-spl; +}; + +&clks { + u-boot,dm-spl; +}; + +&gpio1 { + u-boot,dm-spl; +}; + +&gpio2 { + u-boot,dm-spl; +}; + +&gpio3 { + u-boot,dm-spl; +}; + +&gpio5 { + u-boot,dm-spl; }; &gpt1 {
@@ -19,6 +51,8 @@ }; &semc { + u-boot,dm-spl; + bank1: bank at 0 { u-boot,dm-spl; };
arch/arm/dts/imxrt1020.dtsi +0 -10
@@ -23,7 +23,6 @@ }; clocks { - u-boot,dm-spl; ckil { compatible = "fsl,imx-ckil", "fixed-clock"; #clock-cells = <0>;
@@ -37,7 +36,6 @@ }; osc: osc { - u-boot,dm-spl; compatible = "fsl,imx-osc", "fixed-clock"; #clock-cells = <0>; clock-frequency = <24000000>;
@@ -45,10 +43,7 @@ }; soc { - u-boot,dm-spl; - semc: semc at 402f0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-semc"; reg = <0x402f0000 0x4000>; clocks = <&clks IMXRT1020_CLK_SEMC>;
@@ -73,7 +68,6 @@ }; clks: ccm at 400fc000 { - u-boot,dm-spl; compatible = "fsl,imxrt1020-ccm"; reg = <0x400fc000 0x4000>; interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
@@ -82,7 +76,6 @@ }; usdhc1: usdhc at 402c0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-usdhc"; reg = <0x402c0000 0x10000>; interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -95,7 +88,6 @@ }; gpio1: gpio at 401b8000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401b8000 0x4000>; interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
@@ -107,7 +99,6 @@ }; gpio2: gpio at 401bc000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401bc000 0x4000>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
@@ -119,7 +110,6 @@ }; gpio3: gpio at 401c0000 { - u-boot,dm-spl; compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; reg = <0x401c0000 0x4000>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
Signature · 1 line
2.25.1
PATCH 2/3 ARM: dts: imxrt1020-evk: move all u-boot, dm-spl to imxrt1020-evk-u-boot.dtsi file
Quoted 6 lines
At the moment a lot of u-boot,dm-spl properties are present in board .dts file but this is not correct since u-boot,dm-spl property is u-boot specific and must be listed into the separate
imrt1020-evk-u-boot.dtsifile. So let's move every u-boot,dm-spl property present inimxrt1020-evk.dtstoimxrt1020-evk-u-boot.dtsifile.Signed-off-by Giulio Benetti <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 3/3 ARM: dts: imxrt1020: add gpio5 node to this SoC
In reply to Giulio Benettii.MXRT1020 supports gpio5, so let's add a node for it.
--- arch/arm/dts/imxrt1020.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
arch/arm/dts/imxrt1020.dtsi +11 -0
@@ -120,6 +120,17 @@ #interrupt-cells = <2>; }; + gpio5: gpio at 400c0000 { + compatible = "fsl,imxrt-gpio", "fsl,imx35-gpio"; + reg = <0x400c0000 0x4000>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + gpt1: gpt1 at 401ec000 { compatible = "fsl,imxrt-gpt"; reg = <0x401ec000 0x4000>;
Signature · 1 line
2.25.1
PATCH 3/3 ARM: dts: imxrt1020: add gpio5 node to this SoC
Quoted 2 lines
i.MXRT1020 supports gpio5, so let's add a node for it.
Signed-off-by Giulio Benetti <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
PATCH 1/3 ARM: dts: imxrt1050-evk: move all u-boot, dm-spl to imxrt1050-evk-u-boot.dtsi file
In reply to Giulio BenettiQuoted 6 lines
At the moment a lot of u-boot,dm-spl properties are present in board .dts file but this is not correct since u-boot,dm-spl property is u-boot specific and must be listed into the separate
imrt1050-evk-u-boot.dtsifile. So let's move every u-boot,dm-spl property present inimxrt1050-evk.dtstoimxrt1050-evk-u-boot.dtsifile.Signed-off-by Giulio Benetti <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================