drm/vc4: hdmi: Support the 4k @ 60Hz modes
Subsystems (3)
v6 cover drm/vc4: hdmi: Support the 4k @ 60Hz modes
Hi,
Here is a series that enables the higher resolutions on the HDMI0 Controller found in the BCM2711 (RPi4).
In order to work it needs a few adjustments to config.txt, most notably to enable the enable_hdmi_4kp60 option.
Let me know what you think,
Maxime
---
Changes from v5:
- Fixed unused variables warning
Changes from v4:
- Removed the patches already applied
- Added various fixes for the issues that have been discovered on the downstream tree
Changes from v3:
- Rework the encoder retrieval code that was broken on the RPi3 and older
- Fix a scrambling enabling issue on some display
Changes from v2:
- Gathered the various tags
- Added Cc stable when relevant
- Split out the check to test whether the scrambler is required into an helper
- Fixed a bug where the scrambler state wouldn't be tracked properly if it was enabled at boot
Changes from v1:
- Dropped the range accessors
- Drop the mention of force_turbo
- Reordered the SCRAMBLER_CTL register to match the offset
- Removed duplicate HDMI_14_MAX_TMDS_CLK define
- Warn about enable_hdmi_4kp60 only if there's some modes that can't be reached
- Rework the BVB clock computation
Maxime Ripard (10):
drm/vc4: hdmi: Remove the DDC probing for status detection drm/vc4: hdmi: Fix HPD GPIO detection
drm/vc4: Make vc4_crtc_get_encoder public drm/vc4: crtc: Add encoder to vc4_crtc_config_pv prototype drm/vc4: crtc: Rework the encoder retrieval code (again) drm/vc4: crtc: Add some logging
drm/vc4: Leverage the load tracker on the BCM2711 drm/vc4: hdmi: Raise the maximum clock rate drm/vc4: hdmi: Enable the scrambler on reconnection drm/vc4: Increase the core clock based on HVS load
drivers/gpu/drm/vc4/vc4_crtc.c | 60 ++++++++------ drivers/gpu/drm/vc4/vc4_debugfs.c | 7 +- drivers/gpu/drm/vc4/vc4_drv.h | 9 ++- drivers/gpu/drm/vc4/vc4_hdmi.c | 20 +++-- drivers/gpu/drm/vc4/vc4_kms.c | 126 +++++++++++++++++++++++++----- drivers/gpu/drm/vc4/vc4_plane.c | 5 -- 6 files changed, 164 insertions(+), 63 deletions(-)
Signature · 1 line
2.31.1
PATCH v6 1/10 drm/vc4: hdmi: Remove the DDC probing for status detection
Commit 9d44abbbb8d5 ("drm/vc4: Fall back to using an EDID probe in the absence of a GPIO.") added some code to read the EDID through DDC in the HDMI driver detect hook since the Pi3 had no HPD GPIO back then. However, commit b1b8f45b3130 ("ARM: dts: bcm2837: Add missing GPIOs of Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it comes out of standy will deassert the HPD line, but the EDID will remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4, where the DDC probing will be our primary mean to detect a display, and thus we will never detect the HPD pulse. This was fine before since the pulse was small enough that we would never detect it, and we also didn't have anything (like the scrambler) that needed to be set up in the display.
However, now that we have both, the display during the HPD pulse will clear its scrambler status, and since we won't detect the disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 -- 1 file changed, 2 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +0 -2
@@ -169,8 +169,6 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)if (vc4_hdmi->hpd_gpio &&gpiod_get_value_cansleep (vc4_hdmi->hpd_gpio)) { connected = true; - }else if (drm_probe_ddc (vc4_hdmi->ddc)) { - connected = true; }else if (HDMI_READ (HDMI_HOTPLUG ) &VC4_HDMI_HOTPLUG_CONNECTED ) { connected = true; }
Signature · 1 line
2.31.1
PATCH v6 2/10 drm/vc4: hdmi: Fix HPD GPIO detection
In reply to Maxime RipardPrior to commit 6800234ceee0 ("drm/vc4: hdmi: Convert to gpiod"), in the detect hook, if we had an HPD GPIO we would only rely on it and return whatever state it was in.
However, that commit changed that by mistake to only consider the case where we have a GPIO and it returns a logical high, and would fall back to the other methods otherwise.
Since we can read the EDIDs when the HPD signal is low on some displays, we changed the detection status from disconnected to connected, and we would ignore an HPD pulse.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +3 -3
@@ -166,9 +166,9 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force)struct vc4_hdmi *vc4_hdmi =connector_to_vc4_hdmi (connector);bool connected = false; -if (vc4_hdmi->hpd_gpio && -gpiod_get_value_cansleep (vc4_hdmi->hpd_gpio)) { - connected = true; +if (vc4_hdmi->hpd_gpio) { +if (gpiod_get_value_cansleep (vc4_hdmi->hpd_gpio)) + connected = true; }else if (HDMI_READ (HDMI_HOTPLUG ) &VC4_HDMI_HOTPLUG_CONNECTED ) { connected = true; }
Signature · 1 line
2.31.1
PATCH v6 3/10 drm/vc4: Make vc4_crtc_get_encoder public
In reply to Maxime RipardWe'll need that function in vc4_kms to compute the core clock rate requirements.
--- drivers/gpu/drm/vc4/vc4_crtc.c | 8 ++++---- drivers/gpu/drm/vc4/vc4_drv.h | 5 +++++ 2 files changed, 9 insertions(+), 4 deletions(-)
drivers/gpu/drm/vc4/vc4_crtc.c +4 -4
@@ -279,10 +279,10 @@ static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,* allows drivers to push pixels to more than one encoder from the * same CRTC. */ -static struct drm_encoder *vc4_get_crtc_encoder (struct drm_crtc *crtc, -struct drm_atomic_state *state, -struct drm_connector_state *(*get_state)(struct drm_atomic_state *state, -struct drm_connector *connector)) +struct drm_encoder *vc4_get_crtc_encoder (struct drm_crtc *crtc, +struct drm_atomic_state *state, +struct drm_connector_state *(*get_state)(struct drm_atomic_state *state, +struct drm_connector *connector)) {struct drm_connector *connector;struct drm_connector_list_iter conn_iter;
drivers/gpu/drm/vc4/vc4_drv.h +5 -0
@@ -515,6 +515,11 @@ vc4_crtc_to_vc4_pv_data(const struct vc4_crtc *crtc) return container_of(data, struct vc4_pv_data, base); } +struct drm_encoder *vc4_get_crtc_encoder (struct drm_crtc *crtc, +struct drm_atomic_state *state, +struct drm_connector_state *(*get_state)(struct drm_atomic_state *state, +struct drm_connector *connector)); +struct vc4_crtc_state {struct drm_crtc_state base;/* Dlist area for this CRTC configuration. */
Signature · 1 line
2.31.1
PATCH v6 4/10 drm/vc4: crtc: Add encoder to vc4_crtc_config_pv prototype
In reply to Maxime Ripardvc4_crtc_config_pv() retrieves the encoder again, even though its only caller, vc4_crtc_atomic_enable(), already did.
Pass the encoder pointer as an argument instead of going through all the connectors to retrieve it again.
--- drivers/gpu/drm/vc4/vc4_crtc.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/gpu/drm/vc4/vc4_crtc.c +3 -4
@@ -313,12 +313,11 @@ static void vc4_crtc_pixelvalve_reset(struct drm_crtc *crtc)CRTC_WRITE (PV_CONTROL ,CRTC_READ (PV_CONTROL ) |PV_CONTROL_FIFO_CLR ); } -static void vc4_crtc_config_pv (struct drm_crtc *crtc,struct drm_atomic_state *state) +static void vc4_crtc_config_pv (struct drm_crtc *crtc,struct drm_encoder *encoder, +struct drm_atomic_state *state) {struct drm_device *dev = crtc->dev;struct vc4_dev *vc4 =to_vc4_dev (dev); -struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, state, - drm_atomic_get_new_connector_state);struct vc4_encoder *vc4_encoder =to_vc4_encoder (encoder);struct vc4_crtc *vc4_crtc =to_vc4_crtc (crtc);const struct vc4_pv_data *pv_data =vc4_crtc_to_vc4_pv_data (vc4_crtc);
@@ -580,7 +579,7 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,if (vc4_encoder->pre_crtc_configure) vc4_encoder->pre_crtc_configure (encoder, state); -vc4_crtc_config_pv (crtc, state); +vc4_crtc_config_pv (crtc, encoder, state);CRTC_WRITE (PV_CONTROL ,CRTC_READ (PV_CONTROL ) |PV_CONTROL_EN );
Signature · 1 line
2.31.1
PATCH v6 5/10 drm/vc4: crtc: Rework the encoder retrieval code (again)
In reply to Maxime RipardIt turns out the encoder retrieval code, in addition to being unnecessarily complicated, has a bug when only the planes and crtcs are affected by a given atomic commit.
Indeed, in such a case, either drm_atomic_get_old_connector_state or drm_atomic_get_new_connector_state will return NULL and thus our encoder retrieval code will not match on anything.
We can however simplify the code by using drm_for_each_encoder_mask, the drm_crtc_state storing the encoders a given CRTC is connected to directly and without relying on any other state.
--- drivers/gpu/drm/vc4/vc4_crtc.c | 30 +++++++++--------------------- drivers/gpu/drm/vc4/vc4_drv.h | 4 +--- 2 files changed, 10 insertions(+), 24 deletions(-)
drivers/gpu/drm/vc4/vc4_crtc.c +9 -21
@@ -280,26 +280,14 @@ static u32 vc4_crtc_get_fifo_full_level_bits(struct vc4_crtc *vc4_crtc,* same CRTC. */ struct drm_encoder *vc4_get_crtc_encoder (struct drm_crtc *crtc, -struct drm_atomic_state *state, -struct drm_connector_state *(*get_state)(struct drm_atomic_state *state, -struct drm_connector *connector)) +struct drm_crtc_state *state) { -struct drm_connector *connector; -struct drm_connector_list_iter conn_iter; +struct drm_encoder *encoder; -drm_connector_list_iter_begin (crtc->dev, &conn_iter); -drm_for_each_connector_iter (connector, &conn_iter) { -struct drm_connector_state *conn_state =get_state (state, connector); +WARN_ON (hweight32 (state->encoder_mask) >1 ); -if (!conn_state) -continue ; - -if (conn_state->crtc == crtc) { -drm_connector_list_iter_end (&conn_iter); -return connector->encoder; - } - } -drm_connector_list_iter_end (&conn_iter); +drm_for_each_encoder_mask (encoder, crtc->dev, state->encoder_mask) +return encoder;return NULL ; }
@@ -533,8 +521,7 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,struct drm_crtc_state *old_state =drm_atomic_get_old_crtc_state (state, crtc);struct vc4_crtc_state *old_vc4_state =to_vc4_crtc_state (old_state); -struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, state, - drm_atomic_get_old_connector_state); +struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, old_state);struct drm_device *dev = crtc->dev;require_hvs_enabled (dev);
@@ -561,10 +548,11 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,static void vc4_crtc_atomic_enable (struct drm_crtc *crtc,struct drm_atomic_state *state) { +struct drm_crtc_state *new_state =drm_atomic_get_new_crtc_state (state, + crtc);struct drm_device *dev = crtc->dev;struct vc4_crtc *vc4_crtc =to_vc4_crtc (crtc); -struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, state, - drm_atomic_get_new_connector_state); +struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, new_state);struct vc4_encoder *vc4_encoder =to_vc4_encoder (encoder);require_hvs_enabled (dev);
drivers/gpu/drm/vc4/vc4_drv.h +1 -3
@@ -516,9 +516,7 @@ vc4_crtc_to_vc4_pv_data(const struct vc4_crtc *crtc) }struct drm_encoder *vc4_get_crtc_encoder (struct drm_crtc *crtc, -struct drm_atomic_state *state, -struct drm_connector_state *(*get_state)(struct drm_atomic_state *state, -struct drm_connector *connector)); +struct drm_crtc_state *state);struct vc4_crtc_state {struct drm_crtc_state base;
Signature · 1 line
2.31.1
PATCH v6 6/10 drm/vc4: crtc: Add some logging
In reply to Maxime RipardThe encoder retrieval code has been a source of bugs and glitches in the past and the crtc <-> encoder association been wrong in a number of different ways.
Add some logging to quickly spot issues if they occur.
--- drivers/gpu/drm/vc4/vc4_crtc.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/gpu/drm/vc4/vc4_crtc.c +6 -0
@@ -524,6 +524,9 @@ static void vc4_crtc_atomic_disable(struct drm_crtc *crtc,struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, old_state);struct drm_device *dev = crtc->dev; +drm_dbg (dev,"Disabling CRTC %s (%u) connected to Encoder %s (%u)" , + crtc->name, crtc->base.id, encoder->name, encoder->base.id); +require_hvs_enabled (dev);/* Disable vblank irq handling before crtc is disabled. */
@@ -555,6 +558,9 @@ static void vc4_crtc_atomic_enable(struct drm_crtc *crtc,struct drm_encoder *encoder =vc4_get_crtc_encoder (crtc, new_state);struct vc4_encoder *vc4_encoder =to_vc4_encoder (encoder); +drm_dbg (dev,"Enabling CRTC %s (%u) connected to Encoder %s (%u)" , + crtc->name, crtc->base.id, encoder->name, encoder->base.id); +require_hvs_enabled (dev);/* Enable vblank irq handling before crtc is started otherwise
Signature · 1 line
2.31.1
PATCH v6 7/10 drm/vc4: Leverage the load tracker on the BCM2711
In reply to Maxime RipardThe load tracker was initially designed to report and warn about a load too high for the HVS. To do so, it computes for each plane the impact it's going to have on the HVS, and will warn (if it's enabled) if we go over what the hardware can process.
While the limits being used are a bit irrelevant to the BCM2711, the algorithm to compute the HVS load will be one component used in order to compute the core clock rate on the BCM2711.
Let's remove the hooks to prevent the load tracker to do its computation, but since we don't have the same limits, don't check them against them, and prevent the debugfs file to enable it from being created.
--- drivers/gpu/drm/vc4/vc4_debugfs.c | 7 +++++-- drivers/gpu/drm/vc4/vc4_drv.h | 3 --- drivers/gpu/drm/vc4/vc4_kms.c | 16 +++++----------- drivers/gpu/drm/vc4/vc4_plane.c | 5 ----- 4 files changed, 10 insertions(+), 21 deletions(-)
drivers/gpu/drm/vc4/vc4_debugfs.c +5 -2
@@ -7,6 +7,7 @@#include <linux/circ_buf.h> #include <linux/ctype.h> #include <linux/debugfs.h> +#include <linux/platform_device.h> #include "vc4_drv.h" #include "vc4_regs.h"
@@ -26,8 +27,10 @@ vc4_debugfs_init(struct drm_minor *minor)struct vc4_dev *vc4 =to_vc4_dev (minor->dev);struct vc4_debugfs_info_entry *entry; -debugfs_create_bool ("hvs_load_tracker" ,S_IRUGO |S_IWUSR , - minor->debugfs_root, &vc4->load_tracker_enabled); +if (!of_device_is_compatible (vc4->hvs->pdev->dev.of_node, +"brcm,bcm2711-vc5" )) +debugfs_create_bool ("hvs_load_tracker" ,S_IRUGO |S_IWUSR , + minor->debugfs_root, &vc4->load_tracker_enabled);list_for_each_entry (entry, &vc4->debugfs_list, link) { drm_debugfs_create_files(&entry->info, 1,
drivers/gpu/drm/vc4/vc4_drv.h +0 -3
@@ -200,9 +200,6 @@ struct vc4_dev {int power_refcount; -/* Set to true when the load tracker is supported. */ -bool load_tracker_available; -/* Set to true when the load tracker is active. */ bool load_tracker_enabled;
drivers/gpu/drm/vc4/vc4_kms.c +5 -11
@@ -551,9 +551,6 @@ static int vc4_load_tracker_atomic_check(struct drm_atomic_state *state)struct drm_plane *plane;int i; -if (!vc4->load_tracker_available) -return 0 ; - priv_state =drm_atomic_get_private_obj_state (state, &vc4->load_tracker);if (IS_ERR (priv_state))
@@ -628,9 +625,6 @@ static void vc4_load_tracker_obj_fini(struct drm_device *dev, void *unused) {struct vc4_dev *vc4 =to_vc4_dev (dev); -if (!vc4->load_tracker_available) -return ; -drm_atomic_private_obj_fini (&vc4->load_tracker); }
@@ -638,9 +632,6 @@ static int vc4_load_tracker_obj_init(struct vc4_dev *vc4) {struct vc4_load_tracker_state *load_state; -if (!vc4->load_tracker_available) -return 0 ; - load_state =kzalloc (sizeof (*load_state),GFP_KERNEL );if (!load_state)return -ENOMEM ;
@@ -868,9 +859,12 @@ int vc4_kms_load(struct drm_device *dev) "brcm,bcm2711-vc5");int ret; +/* +* The limits enforced by the load tracker aren't relevant for +* the BCM2711, but the load tracker computations are used for +* the core clock rate calculation. +*/ if (!is_vc5) { - vc4->load_tracker_available = true; -/* Start with the load tracker enabled. Can be * disabled through the debugfs load_tracker file. */
drivers/gpu/drm/vc4/vc4_plane.c +0 -5
@@ -529,11 +529,6 @@ static void vc4_plane_calc_load(struct drm_plane_state *state)struct vc4_plane_state *vc4_state;struct drm_crtc_state *crtc_state;unsigned int vscale_factor; -struct vc4_dev *vc4; - - vc4 =to_vc4_dev (state->plane->dev); -if (!vc4->load_tracker_available) -return ; vc4_state =to_vc4_plane_state (state); crtc_state = drm_atomic_get_existing_crtc_state(state->state,
Signature · 1 line
2.31.1
PATCH v6 8/10 drm/vc4: hdmi: Raise the maximum clock rate
In reply to Maxime RipardNow that we have the infrastructure in place, we can raise the maximum pixel rate we can reach for HDMI0 on the BCM2711.
HDMI1 is left untouched since its pixelvalve has a smaller FIFO and would need a clock faster than what we can provide to support the same modes.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +1 -1
@@ -2282,7 +2282,7 @@ static const struct vc4_hdmi_variant bcm2711_hdmi0_variant = { .encoder_type = VC4_ENCODER_TYPE_HDMI0, .debugfs_name = "hdmi0_regs", .card_name = "vc4-hdmi-0", - .max_pixel_clock = HDMI_14_MAX_TMDS_CLK, + .max_pixel_clock = 600000000, .registers = vc5_hdmi_hdmi0_fields, .num_registers = ARRAY_SIZE(vc5_hdmi_hdmi0_fields), .phy_lane_mapping = {
Signature · 1 line
2.31.1
PATCH v6 9/10 drm/vc4: hdmi: Enable the scrambler on reconnection
In reply to Maxime RipardIf we have a state already and disconnect/reconnect the display, the SCDC messages won't be sent again since we didn't go through a disable / enable cycle.
In order to fix this, let's call the vc4_hdmi_enable_scrambling function in the detect callback if there is a mode and it needs the scrambler to be enabled.
--- drivers/gpu/drm/vc4/vc4_hdmi.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-)
drivers/gpu/drm/vc4/vc4_hdmi.c +9 -1
@@ -160,6 +160,8 @@ static void vc4_hdmi_cec_update_clk_div(struct vc4_hdmi *vc4_hdmi)static void vc4_hdmi_cec_update_clk_div (struct vc4_hdmi *vc4_hdmi) {}#endif +static void vc4_hdmi_enable_scrambling (struct drm_encoder *encoder); +static enum drm_connector_status vc4_hdmi_connector_detect (struct drm_connector *connector,bool force) {
@@ -184,6 +186,8 @@ vc4_hdmi_connector_detect(struct drm_connector *connector, bool force) } } +vc4_hdmi_enable_scrambling (&vc4_hdmi->encoder.base.base); +return connector_status_connected; }
@@ -539,9 +543,13 @@ static bool vc4_hdmi_supports_scrambling(struct drm_encoder *encoder,static void vc4_hdmi_enable_scrambling (struct drm_encoder *encoder) { -struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode; +struct drm_display_mode *mode;struct vc4_hdmi *vc4_hdmi =encoder_to_vc4_hdmi (encoder); +if (!encoder->crtc || !encoder->crtc->state) +return ; + + mode = &encoder->crtc->state->adjusted_mode;if (!vc4_hdmi_supports_scrambling (encoder, mode))return ;
Signature · 1 line
2.31.1
PATCH v6 10/10 drm/vc4: Increase the core clock based on HVS load
In reply to Maxime RipardDepending on a given HVS output (HVS to PixelValves) and input (planes attached to a channel) load, the HVS needs for the core clock to be raised above its boot time default.
Failing to do so will result in a vblank timeout and a stalled display pipeline.
--- drivers/gpu/drm/vc4/vc4_crtc.c | 15 +++++ drivers/gpu/drm/vc4/vc4_drv.h | 3 + drivers/gpu/drm/vc4/vc4_kms.c | 110 ++++++++++++++++++++++++++++++--- 3 files changed, 119 insertions(+), 9 deletions(-)
drivers/gpu/drm/vc4/vc4_crtc.c +15 -0
@@ -642,12 +642,27 @@ static int vc4_crtc_atomic_check(struct drm_crtc *crtc,struct vc4_crtc_state *vc4_state =to_vc4_crtc_state (crtc_state);struct drm_connector *conn;struct drm_connector_state *conn_state; +struct drm_encoder *encoder;int ret, i; ret =vc4_hvs_atomic_check (crtc, state);if (ret)return ret; + encoder =vc4_get_crtc_encoder (crtc, crtc_state); +if (encoder) { +const struct drm_display_mode *mode = &crtc_state->adjusted_mode; +struct vc4_encoder *vc4_encoder =to_vc4_encoder (encoder); + + mode = &crtc_state->adjusted_mode; +if (vc4_encoder->type ==VC4_ENCODER_TYPE_HDMI0 ) { + vc4_state->hvs_load =max (mode->clock * mode->hdisplay / mode->htotal +1000 , + mode->clock *9 /10 ) *1000 ; + }else { + vc4_state->hvs_load = mode->clock *1000 ; + } + } +for_each_new_connector_in_state (state, conn, conn_state, i) {if (conn_state->crtc != crtc)
drivers/gpu/drm/vc4/vc4_drv.h +3 -0
@@ -319,6 +319,7 @@ struct vc4_hvs {u32 __iomem *dlist;struct clk *core_clk; +struct clk_request *core_req;/* Memory manager for CRTCs to allocate space in the display * list. Units are dwords.
@@ -530,6 +531,8 @@ struct vc4_crtc_state {unsigned int bottom; } margins; +unsigned long hvs_load; +/* Transitional state below, only valid during atomic commits */ bool update_muxing; };
drivers/gpu/drm/vc4/vc4_kms.c +101 -9
168 lines not on this page · raw message
Signature · 1 line
2.31.1