Skip to contentSkip to conversation

arm64: dts: qcom: Add support for SM8450 SoC and QRD board

PATCH Superseded Vinod Koul 3 participants 44 messages Dec 1, 2021 – Dec 9, 2021

Subsystems (3)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Vinod Koul

author
#0 lore raw

cover arm64: dts: qcom: Add support for SM8450 SoC and QRD board

Snapdragon 8 Gen 1 Mobile Platform [1] (SM8450) is the latest Qualcomm SoC announced today.

This series adds the DTS support including clocks, tlmm, smmu, regulators, ufs, interconnects, pmics and cpufreq found in the SM8450 QRD board.

[1]: https://www.qualcomm.com/products/snapdragon-8-gen-1-mobile-platform

Dmitry Baryshkov (2):
arm64: dts: qcom: sm8450: Add rpmhpd node
arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes

Vinod Koul (12):
arm64: dts: qcom: Add base SM8450 DTSI
arm64: dts: qcom: Add base SM8450 QRD DTS
arm64: dts: qcom: sm8450: Add tlmm nodes
arm64: dts: qcom: sm8450-qrd: Add reserved gpio range for QRD
arm64: dts: qcom: sm8450: Add reserved memory nodes
arm64: dts: qcom: sm8450: add smmu nodes
arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes
arm64: dts: qcom: sm8450: add ufs nodes
arm64: dts: qcom: sm8450-qrd: enable ufs nodes
arm64: dts: qcom: sm8450: add interconnect nodes
arm64: dts: qcom: sm8450: add spmi node
arm64: dts: qcom: sm8450-qrd: include pmic files

Vladimir Zapolskiy (1):
arm64: dts: qcom: sm8450: add cpufreq support

 arch/arm64/boot/dts/qcom/Makefile       |    1 +
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts |  379 ++++++++
 arch/arm64/boot/dts/qcom/sm8450.dtsi    | 1142 +++++++++++++++++++++++
 3 files changed, 1522 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450-qrd.dts
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
Signature · 1 line
2.31.1
author
#1 lore raw

PATCH 1/15 arm64: dts: qcom: Add base SM8450 DTSI

This add based DTSI for SM8450 SoC and includes base description of CPUs, GCC, RPMHCC, UART, interuupt-controller which helps to boot to shell with console on boards with this SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 476 +++++++++++++++++++++++++++
 1 file changed, 476 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +476 -0
new file mode 100644
index 000000000000..d838283bde4b
@@ -0,0 +1,476 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8450.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
+			L2_0: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+				      compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&L2_100>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
+			L2_100: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			next-level-cache = <&L2_200>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
+			L2_200: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			next-level-cache = <&L2_300>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
+			L2_300: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			next-level-cache = <&L2_400>;
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
+			L2_400: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			next-level-cache = <&L2_500>;
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
+			L2_500: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			next-level-cache = <&L2_600>;
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
+			L2_600: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			next-level-cache = <&L2_700>;
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
+			L2_700: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "silver-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <274>;
+				exit-latency-us = <480>;
+				min-residency-us = <3934>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "gold-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <327>;
+				exit-latency-us = <1502>;
+				min-residency-us = <4488>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-l3-off";
+				arm,psci-suspend-param = <0x4100c344>;
+				entry-latency-us = <584>;
+				exit-latency-us = <2332>;
+				min-residency-us = <6118>;
+				local-timer-stop;
+			};
+
+			CLUSTER_SLEEP_1: cluster-sleep-1 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-power-collapse";
+				arm,psci-suspend-param = <0x4100c344>;
+				entry-latency-us = <2893>;
+				exit-latency-us = <4023>;
+				min-residency-us = <9987>;
+				local-timer-stop;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sm8450", "qcom,scm";
+			#reset-cells = <1>;
+		};
+	};
+
+	memory@a0000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0xa0000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		CPU_PD0: cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sm8450";
+			reg = <0x0 0x00100000 0x0 0x1f4200>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clock-names = "bi_tcxo", "sleep_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+		};
+
+		qupv3_id_0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x009c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm8450-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
+			qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
+					  <94 609 31>, <125 63 1>, <126 716 12>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		intc: interrupt-controller@17100000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0x0 0x40000>;
+			reg = <0x0 0x17100000 0x0 0x10000>,     /* GICD */
+			      <0x0 0x17180000 0x0 0x200000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		timer@17420000 {
+			compatible = "arm,armv7-timer-mem";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			reg = <0x0 0x17420000 0x0 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17421000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17421000 0x0 0x1000>,
+				      <0x0 0x17422000 0x0 0x1000>;
+			};
+
+			frame@17423000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17423000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17425000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17425000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17427000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17427000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17429000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x17429000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@1742b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x1742b000 0x0 0x1000>;
+				status = "disabled";
+			};
+
+			frame@1742d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x0 0x1742d000 0x0 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17a00000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x0 0x17a00000 0x0 0x10000>,
+			      <0x0 0x17a10000 0x0 0x10000>,
+			      <0x0 0x17a20000 0x0 0x10000>,
+			      <0x0 0x17a30000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2", "drv-3";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS  3>, <SLEEP_TCS   2>,
+					  <WAKE_TCS    2>, <CONTROL_TCS 0>;
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sm8450-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;
+	};
+};
Signature · 1 line
2.31.1
Reviewed-by on v1 1/15
#2 lore raw

Re: [PATCH 01/15] arm64: dts: qcom: Add base SM8450 DTSI

Quoted 37 lines · Vinod Koul

This add based DTSI for SM8450 SoC and includes base description of CPUs, GCC, RPMHCC, UART, interuupt-controller which helps to boot to shell with console on boards with this SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 476 +++++++++++++++++++++++++++
 1 file changed, 476 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +21 -0
new file mode 100644
index 000000000000..d838283bde4b
@@ -0,0 +1,476 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8450.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";

arch/arm64/boot/dts/qcom/sm8450.dtsi line 31

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +10 -0
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};

No clock-output-names for this one?

Other than that:

Konrad

author
#3 lore raw

Re: [PATCH 01/15] arm64: dts: qcom: Add base SM8450 DTSI

Quoted 43 lines · Konrad Dybcio
Quoted 41 lines · Vinod Koul

This add based DTSI for SM8450 SoC and includes base description of CPUs, GCC, RPMHCC, UART, interuupt-controller which helps to boot to shell with console on boards with this SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 476 +++++++++++++++++++++++++++
 1 file changed, 476 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +25 -0
new file mode 100644
index 000000000000..d838283bde4b
@@ -0,0 +1,476 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8450.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+		};
Quoted 8 lines

arch/arm64/boot/dts/qcom/sm8450.dtsi line 31

Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +6 -0
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};

No clock-output-names for this one?

This should have one, will fix and update in v2

Quoted 5 lines

Other than that:

Thanks for the review!

Signature · 1 line
~Vinod
#4 lore raw

Re: [PATCH 01/15] arm64: dts: qcom: Add base SM8450 DTSI

Quoted 53 lines · Vinod Koul
Quoted 43 lines · Konrad Dybcio
Quoted 41 lines · Vinod Koul

This add based DTSI for SM8450 SoC and includes base description of CPUs, GCC, RPMHCC, UART, interuupt-controller which helps to boot to shell with console on boards with this SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 476 +++++++++++++++++++++++++++
 1 file changed, 476 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +25 -0
new file mode 100644
index 000000000000..d838283bde4b
@@ -0,0 +1,476 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8450.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+		};
Quoted 8 lines

arch/arm64/boot/dts/qcom/sm8450.dtsi line 31

Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +6 -0
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};

No clock-output-names for this one?

Quoted 1 line

This should have one, will fix and update in v2

No need, the clock's name is not significant for anything beyond debugging. So if you're going to change something let it be dropping the clock-output-names from &xo_board.

Thanks,
Bjorn

Quoted 10 lines
Quoted 5 lines

Other than that:

Thanks for the review!

Signature · 1 line
~Vinod
#5 lore raw

Re: [PATCH 01/15] arm64: dts: qcom: Add base SM8450 DTSI

In reply to Vinod Koul
Quoted 11 lines · Vinod Koul

This add based DTSI for SM8450 SoC and includes base description of CPUs, GCC, RPMHCC, UART, interuupt-controller which helps to boot to shell with console on boards with this SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 476 +++++++++++++++++++++++++++
 1 file changed, 476 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
arch/arm64/boot/dts/qcom/sm8450.dtsi +0 -0

[..]

arch/arm64/boot/dts/qcom/sm8450.dtsi line 342

Quoted 13 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +13 -0
+		qupv3_id_0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x009c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-debug-uart";

There's nothing special about uart7 on a platform level, so my suggestion is that you use the standard compatible of "qcom,geni-se-qup" here and then override the compatible with "qcom,geni-debug-uart" in the qrd.dts.

Regards,
Bjorn

author
#6 lore raw

PATCH 2/15 arm64: dts: qcom: Add base SM8450 QRD DTS

In reply to Vinod Koul

Add DTS for Qualcomm QRD platform which uses SM8450 SoC

---
 arch/arm64/boot/dts/qcom/Makefile       |  1 +
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 29 +++++++++++++++++++++++++
 2 files changed, 30 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450-qrd.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
index 6b816eb33309..9b37261484cf 100644
@@ -107,3 +107,4 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-sony-xperia-edo-pdx203.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-sony-xperia-edo-pdx206.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-qrd.dtb
arch/arm64/boot/dts/qcom/sm8450-qrd.dts new file +29 -0
new file mode 100644
index 000000000000..127d32502555
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include "sm8450.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SM8450 QRD";
+	compatible = "qcom,sm8450-qrd", "qcom,sm8450";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&uart7 {
+	status = "okay";
+};
Signature · 1 line
2.31.1
Reviewed-by on v1 2/15
#7 lore raw

Re: [PATCH 02/15] arm64: dts: qcom: Add base SM8450 QRD DTS

Quoted 9 lines · Vinod Koul

Add DTS for Qualcomm QRD platform which uses SM8450 SoC

---
 arch/arm64/boot/dts/qcom/Makefile       |  1 +
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 29 +++++++++++++++++++++++++
 2 files changed, 30 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/sm8450-qrd.dts

Konrad

author
#8 lore raw

PATCH 3/15 arm64: dts: qcom: sm8450: Add tlmm nodes

In reply to Vinod Koul

Add tlmm node found in SM8450 SoC and uart pin configuration

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 29 ++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +29 -0
index d838283bde4b..f0b9e80238a2 100644
@@ -343,6 +343,8 @@ uart7: serial@99c000 {
 				reg = <0 0x0099c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_default_state>;
 				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -366,6 +368,33 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sm8450-tlmm";
+			reg = <0 0x0f100000 0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 211>;
+			wakeup-parent = <&pdc>;
+
+			qup_uart7_default_state: qup-uart3-default-state {
+				rx {
+					pins = "gpio26";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+				tx {
+					pins = "gpio27";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+		};
+
 		intc: interrupt-controller@17100000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
Signature · 1 line
2.31.1
#9 lore raw

Re: [PATCH 03/15] arm64: dts: qcom: sm8450: Add tlmm nodes

Quoted 26 lines · Vinod Koul

Add tlmm node found in SM8450 SoC and uart pin configuration

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 29 ++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +4 -0
index d838283bde4b..f0b9e80238a2 100644
@@ -343,6 +343,8 @@ uart7: serial@99c000 {
 				reg = <0 0x0099c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_default_state>;
 				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -366,6 +368,33 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sm8450-tlmm";

arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 382

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +10 -0
+			reg = <0 0x0f100000 0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 211>;
+			wakeup-parent = <&pdc>;
+
+			qup_uart7_default_state: qup-uart3-default-state {

There's a '3' in the node name.

Loos good otherwise.

Thanks,
Bjorn

Quoted 21 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +15 -0
+				rx {
+					pins = "gpio26";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+				tx {
+					pins = "gpio27";
+					function = "qup7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+			};
+		};
+
 		intc: interrupt-controller@17100000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
Signature · 1 line
2.31.1
author
#10 lore raw

PATCH 4/15 arm64: dts: qcom: sm8450-qrd: Add reserved gpio range for QRD

In reply to Vinod Koul

Some tlmm gpios are reserved, so mark them as such in QRD DTS

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +4 -0
index 127d32502555..8dcd41c4e5ab 100644
@@ -24,6 +24,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <36 4>;
+};
+
 &uart7 {
 	status = "okay";
 };
Signature · 1 line
2.31.1
Reviewed-by on v1 4/15
#11 lore raw

Re: [PATCH 04/15] arm64: dts: qcom: sm8450-qrd: Add reserved gpio range for QRD

Quoted 13 lines · Vinod Koul

Some tlmm gpios are reserved, so mark them as such in QRD DTS

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 127d32502555..8dcd41c4e5ab 100644

arch/arm64/boot/dts/qcom/sm8450-qrd.dts &qupv3_id_0 { · line 33

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +4 -0
@@ -24,6 +24,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <36 4>;
+};
+
 &uart7 {
 	status = "okay";
 };

Personally I'd squash this into the patch that introduced the DT and

move it to the end of the series, but I reckon it's fine either way..

Konrad

author
#12 lore raw

Re: [PATCH 04/15] arm64: dts: qcom: sm8450-qrd: Add reserved gpio range for QRD

Quoted 17 lines · Konrad Dybcio
Quoted 15 lines · Vinod Koul

Some tlmm gpios are reserved, so mark them as such in QRD DTS

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 127d32502555..8dcd41c4e5ab 100644
@@ -24,6 +24,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
Quoted 9 lines

arch/arm64/boot/dts/qcom/sm8450-qrd.dts &qupv3_id_0 { · line 33

Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +4 -0
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <36 4>;
+};
+
 &uart7 {
 	status = "okay";
 };

Personally I'd squash this into the patch that introduced the DT and

I feel it is the right things to do, a patch should not touch a different file. soc dts and board dts and two different entities and should be patched separately!

Quoted 4 lines

move it to the end of the series, but I reckon it's fine either way..

Thanks for the detailed review.

Signature · 1 line
~Vinod
#13 lore raw

Re: [PATCH 04/15] arm64: dts: qcom: sm8450-qrd: Add reserved gpio range for QRD

Quoted 28 lines · Vinod Koul
Quoted 17 lines · Konrad Dybcio
Quoted 15 lines · Vinod Koul

Some tlmm gpios are reserved, so mark them as such in QRD DTS

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 4 ++++
 1 file changed, 4 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 127d32502555..8dcd41c4e5ab 100644
@@ -24,6 +24,10 @@ &qupv3_id_0 {
 	status = "okay";
 };
 
Quoted 9 lines

arch/arm64/boot/dts/qcom/sm8450-qrd.dts &qupv3_id_0 { · line 33

Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +4 -0
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <36 4>;
+};
+
 &uart7 {
 	status = "okay";
 };

Personally I'd squash this into the patch that introduced the DT and

Quoted 4 lines

I feel it is the right things to do, a patch should not touch a different file. soc dts and board dts and two different entities and should be patched separately!

You could introduce the qrd.dts slightly later in the series and squash this in there.

Regards,
Bjorn

Quoted 9 lines
Quoted 4 lines

move it to the end of the series, but I reckon it's fine either way..

Thanks for the detailed review.

Signature · 1 line
~Vinod
author
#14 lore raw

PATCH 5/15 arm64: dts: qcom: sm8450: Add reserved memory nodes

In reply to Vinod Koul

Add the reserved memory nodes for SM8450. This is based on the downstream documentation.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 221 +++++++++++++++++++++++++++
 1 file changed, 221 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +221 -0
index f0b9e80238a2..79aead4cba66 100644
@@ -310,6 +310,227 @@ CLUSTER_PD: cpu-cluster0 {
 		};
 	};
 
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			no-map;
+			reg = <0x0 0x80000000 0x0 0x600000>;
+		};
+
+		xbl_dt_log_mem: memory@80600000 {
+			no-map;
+			reg = <0x0 0x80600000 0x0 0x40000>;
+		};
+
+		xbl_ramdump_mem: memory@80640000 {
+			no-map;
+			reg = <0x0 0x80640000 0x0 0x180000>;
+		};
+
+		xbl_sc_mem: memory@807c0000 {
+			no-map;
+			reg = <0x0 0x807c0000 0x0 0x40000>;
+		};
+
+		aop_image_mem: memory@80800000 {
+			no-map;
+			reg = <0x0 0x80800000 0x0 0x60000>;
+		};
+
+		aop_cmd_db_mem: memory@80860000 {
+			compatible = "qcom,cmd-db";
+			no-map;
+			reg = <0x0 0x80860000 0x0 0x20000>;
+		};
+
+		aop_config_mem: memory@80880000 {
+			no-map;
+			reg = <0x0 0x80880000 0x0 0x20000>;
+		};
+
+		tme_crash_dump_mem: memory@808a0000 {
+			no-map;
+			reg = <0x0 0x808a0000 0x0 0x40000>;
+		};
+
+		tme_log_mem: memory@808e0000 {
+			no-map;
+			reg = <0x0 0x808e0000 0x0 0x4000>;
+		};
+
+		uefi_log_mem: memory@808e4000 {
+			no-map;
+			reg = <0x0 0x808e4000 0x0 0x10000>;
+		};
+
+		/* secdata region can be reused by apps */
+		smem: memory@80900000 {
+			compatible = "qcom,smem";
+			no-map;
+			reg = <0x0 0x80900000 0x0 0x200000>;
+			hwlocks = <&tcsr_mutex 3>;
+		};
+
+		cpucp_fw_mem: memory@80b00000 {
+			no-map;
+			reg = <0x0 0x80b00000 0x0 0x100000>;
+		};
+
+		cdsp_secure_heap: memory@80c00000 {
+			no-map;
+			reg = <0x0 0x80c00000 0x0 0x4600000>;
+		};
+
+		camera_mem: memory@85200000 {
+			no-map;
+			reg = <0x0 0x85200000 0x0 0x500000>;
+		};
+
+		video_mem: memory@85700000 {
+			no-map;
+			reg = <0x0 0x85700000 0x0 0x700000>;
+		};
+
+		adsp_mem: memory@85e00000 {
+			no-map;
+			reg = <0x0 0x85e00000 0x0 0x2100000>;
+		};
+
+		slpi_mem: memory@88000000 {
+			no-map;
+			reg = <0x0 0x88000000 0x0 0x1900000>;
+		};
+
+		cdsp_mem: memory@89900000 {
+			no-map;
+			reg = <0x0 0x89900000 0x0 0x2000000>;
+		};
+
+		ipa_fw_mem: memory@8b900000 {
+			no-map;
+			reg = <0x0 0x8b900000 0x0 0x10000>;
+		};
+
+		ipa_gsi_mem: memory@8b910000 {
+			no-map;
+			reg = <0x0 0x8b910000 0x0 0xa000>;
+		};
+
+		gpu_micro_code_mem: memory@8b91a000 {
+			no-map;
+			reg = <0x0 0x8b91a000 0x0 0x2000>;
+		};
+
+		spss_region_mem: memory@8ba00000 {
+			no-map;
+			reg = <0x0 0x8ba00000 0x0 0x180000>;
+		};
+
+		/* First part of the "SPU secure shared memory" region */
+		spu_tz_shared_mem: memory@8bb80000 {
+			no-map;
+			reg = <0x0 0x8bb80000 0x0 0x60000>;
+		};
+
+		/* Second part of the "SPU secure shared memory" region */
+		spu_modem_shared_mem: memory@8bbe0000 {
+			no-map;
+			reg = <0x0 0x8bbe0000 0x0 0x20000>;
+		};
+
+		mpss_mem: memory@8bc00000 {
+			no-map;
+			reg = <0x0 0x8bc00000 0x0 0x13200000>;
+		};
+
+		cvp_mem: memory@9ee00000 {
+			no-map;
+			reg = <0x0 0x9ee00000 0x0 0x700000>;
+		};
+
+		global_sync_mem: memory@a6f00000 {
+			no-map;
+			reg = <0x0 0xa6f00000 0x0 0x100000>;
+		};
+
+		/* uefi region can be reused by apps */
+
+		/* Linux kernel image is loaded at 0xa0000000 */
+
+		oem_vm_mem: memory@bb000000 {
+			no-map;
+			reg = <0x0 0xbb000000 0x0 0x5000000>;
+		};
+
+		mte_mem: memory@c0000000 {
+			no-map;
+			reg = <0x0 0xc0000000 0x0 0x20000000>;
+		};
+
+		qheebsp_reserved_mem: memory@e0000000 {
+			no-map;
+			reg = <0x0 0xe0000000 0x0 0x600000>;
+		};
+
+		cpusys_vm_mem: memory@e0600000 {
+			no-map;
+			reg = <0x0 0xe0600000 0x0 0x400000>;
+		};
+
+		hyp_reserved_mem: memory@e0a00000 {
+			no-map;
+			reg = <0x0 0xe0a00000 0x0 0x100000>;
+		};
+
+		trust_ui_vm_mem: memory@e0b00000 {
+			no-map;
+			reg = <0x0 0xe0b00000 0x0 0x4af3000>;
+		};
+
+		trust_ui_vm_qrtr: memory@e55f3000 {
+			no-map;
+			reg = <0x0 0xe55f3000 0x0 0x9000>;
+		};
+
+		trust_ui_vm_vblk0_ring: memory@e55fc000 {
+			no-map;
+			reg = <0x0 0xe55fc000 0x0 0x4000>;
+		};
+
+		trust_ui_vm_swiotlb: memory@e5600000 {
+			no-map;
+			reg = <0x0 0xe5600000 0x0 0x100000>;
+		};
+
+		tz_stat_mem: memory@e8800000 {
+			no-map;
+			reg = <0x0 0xe8800000 0x0 0x100000>;
+		};
+
+		tags_mem: memory@e8900000 {
+			no-map;
+			reg = <0x0 0xe8900000 0x0 0x1200000>;
+		};
+
+		qtee_mem: memory@e9b00000 {
+			no-map;
+			reg = <0x0 0xe9b00000 0x0 0x500000>;
+		};
+
+		trusted_apps_mem: memory@ea000000 {
+			no-map;
+			reg = <0x0 0xea000000 0x0 0x3900000>;
+		};
+
+		trusted_apps_ext_mem: memory@ed900000 {
+			no-map;
+			reg = <0x0 0xed900000 0x0 0x3b00000>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;
Signature · 1 line
2.31.1
#15 lore raw

Re: [PATCH 05/15] arm64: dts: qcom: sm8450: Add reserved memory nodes

Quoted 15 lines · Vinod Koul

Add the reserved memory nodes for SM8450. This is based on the downstream documentation.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 221 +++++++++++++++++++++++++++
 1 file changed, 221 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +0 -0
index f0b9e80238a2..79aead4cba66 100644
@@ -310,6 +310,227 @@ CLUSTER_PD: cpu-cluster0 {
 		};
 	};

arch/arm64/boot/dts/qcom/sm8450.dtsi CLUSTER_PD: cpu-cluster0 { · line 321

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +9 -0
 
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			no-map;
+			reg = <0x0 0x80000000 0x0 0x600000>;
+		};

All nodes in this patch put no-map before reg, which is precisely not the way

it's done in all other qcom DTs...

[...]

arch/arm64/boot/dts/qcom/sm8450.dtsi CLUSTER_PD: cpu-cluster0 { · line 323

Quoted 2 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +2 -0
+
+		/* uefi region can be reused by apps */

What apps? Facebook? TikTok? Capitalization makes a difference in this

specific case..

arch/arm64/boot/dts/qcom/sm8450.dtsi CLUSTER_PD: cpu-cluster0 { · line 467

Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +8 -0
+
+		/* Linux kernel image is loaded at 0xa0000000 */
+
+		oem_vm_mem: memory@bb000000 {
+			no-map;
+			reg = <0x0 0xbb000000 0x0 0x5000000>;
+		};
+

[...]

Konrad

author
#16 lore raw

Re: [PATCH 05/15] arm64: dts: qcom: sm8450: Add reserved memory nodes

Quoted 30 lines · Konrad Dybcio
Quoted 15 lines · Vinod Koul

Add the reserved memory nodes for SM8450. This is based on the downstream documentation.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 221 +++++++++++++++++++++++++++
 1 file changed, 221 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +0 -0
index f0b9e80238a2..79aead4cba66 100644
@@ -310,6 +310,227 @@ CLUSTER_PD: cpu-cluster0 {
 		};
 	};

arch/arm64/boot/dts/qcom/sm8450.dtsi CLUSTER_PD: cpu-cluster0 { · line 321

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +9 -0
 
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			no-map;
+			reg = <0x0 0x80000000 0x0 0x600000>;
+		};

All nodes in this patch put no-map before reg, which is precisely not the way

Quoted 1 line

it's done in all other qcom DTs...

True, will update it to be consistent across

Quoted 10 lines

[...]

arch/arm64/boot/dts/qcom/sm8450.dtsi

Quoted 2 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +2 -0
+
+		/* uefi region can be reused by apps */

What apps? Facebook? TikTok? Capitalization makes a difference in this

specific case..

Am sure facebook might like you comment, but lets fix that up to not give them such opinion :)

Signature · 1 line
~Vinod
author
#17 lore raw

PATCH 6/15 arm64: dts: qcom: sm8450: add smmu nodes

In reply to Vinod Koul

Add the apps smmu node as found in the SM8450 SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 103 +++++++++++++++++++++++++++
 1 file changed, 103 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +103 -0
index 79aead4cba66..53a6f2275621 100644
@@ -616,6 +616,109 @@ tx {
 			};
 		};
 
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <2>;
+			interrupts =    <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		intc: interrupt-controller@17100000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
Signature · 1 line
2.31.1
author
#19 lore raw

PATCH 7/15 arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes

In reply to Vinod Koul

Add the RPMH regulators found in QRD-SM8450 platform

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 322 ++++++++++++++++++++++++
 1 file changed, 322 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +322 -0
index 8dcd41c4e5ab..218eb3ce1ee5 100644
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8450.dtsi"
 
 / {
@@ -18,6 +19,327 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	pm8350-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+
+		vdd-l1-l4-supply = <&vreg_s11b_0p95>;
+		vdd-l2-l7-supply = <&vreg_bob>;
+		vdd-l3-l5-supply = <&vreg_bob>;
+		vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
+		vdd-l8-supply = <&vreg_s2h_0p95>;
+
+		vreg_s10b_1p8: smps10 {
+			regulator-name = "vreg_s10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_s11b_0p95: smps11 {
+			regulator-name = "vreg_s11b_0p95";
+			regulator-min-microvolt = <848000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		vreg_s12b_1p25: smps12 {
+			regulator-name = "vreg_s12b_1p25";
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_l1b_0p91: ldo1 {
+			regulator-name = "vreg_l1b_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p07: ldo2 {
+			regulator-name = "vreg_l2b_3p07";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b_0p9: ldo3 {
+			regulator-name = "vreg_l3b_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_0p88: ldo5 {
+			regulator-name = "vreg_l5b_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <888000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p2: ldo6 {
+			regulator-name = "vreg_l6b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p5: ldo7 {
+			regulator-name = "vreg_l7b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_1p2: ldo9 {
+			regulator-name = "vreg_l9b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+
+		vdd-l1-l12-supply = <&vreg_bob>;
+		vdd-l2-l8-supply = <&vreg_bob>;
+		vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+		vdd-l6-l9-l11-supply = <&vreg_bob>;
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_s1c_1p86: smps1 {
+			regulator-name = "vreg_s1c_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		vreg_s10c_1p05: smps10 {
+			regulator-name = "vreg_s10c_1p05";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_bob: bob {
+			regulator-name = "vreg_bob";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-name = "vreg_l1c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_3p0: ldo3 {
+			regulator-name = "vreg_l3c_3p0";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c_1p8: ldo4 {
+			regulator-name = "vreg_l4c_1p8";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5c_1p8: ldo5 {
+			regulator-name = "vreg_l5c_1p8";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c_1p8: ldo6 {
+			regulator-name = "vreg_l6c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-name = "vreg_l7c_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-name = "vreg_l8c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p96: ldo9 {
+			regulator-name = "vreg_l9c_2p96";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c_1p8: ldo12 {
+			regulator-name = "vreg_l12c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c_3p0: ldo13 {
+			regulator-name = "vreg_l13c_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8450-rpmh-regulators {
+		compatible = "qcom,pm8450-rpmh-regulators";
+		qcom,pmic-id = "h";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vdd-l2-supply = <&vreg_bob>;
+		vdd-l3-supply = <&vreg_bob>;
+		vdd-l4-supply = <&vreg_bob>;
+
+		vreg_s2h_0p95: smps2 {
+			regulator-name = "vreg_s2h_0p95";
+			regulator-min-microvolt = <848000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		vreg_s3h_0p5: smps3 {
+			regulator-name = "vreg_s3h_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <500000>;
+		};
+
+		vreg_l2h_0p91: ldo2 {
+			regulator-name = "vreg_l2h_0p91";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3h_0p91: ldo3 {
+			regulator-name = "vreg_l3h_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+	};
+
+	pmr735a-rpmh-regulators {
+		compatible = "qcom,pmr735a-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+
+		vdd-l1-l2-supply = <&vreg_s2e_0p85>;
+		vdd-l3-supply = <&vreg_s1e_1p25>;
+		vdd-l4-supply = <&vreg_s1c_1p86>;
+		vdd-l5-l6-supply = <&vreg_s1c_1p86>;
+		vdd-l7-bob-supply = <&vreg_bob>;
+
+		vreg_s1e_1p25: smps1 {
+			regulator-name = "vreg_s1e_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1296000>;
+		};
+
+		vreg_s2e_0p85: smps2 {
+			regulator-name = "vreg_s2e_0p85";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_l1e_0p8: ldo1 {
+			regulator-name = "vreg_l1e_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l4e_1p7: ldo4 {
+			regulator-name = "vreg_l4e_1p7";
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+		};
+
+		vreg_l5e_0p88: ldo5 {
+			regulator-name = "vreg_l5e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l6e_1p2: ldo6 {
+			regulator-name = "vreg_l6e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+	};
 };
 
 &qupv3_id_0 {
Signature · 1 line
2.31.1
author
#21 lore raw

PATCH 8/15 arm64: dts: qcom: sm8450: add ufs nodes

In reply to Vinod Koul

Add the UFS and QMP PHY node for SM8450 SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 72 ++++++++++++++++++++++++++++
 1 file changed, 72 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +72 -0
index 53a6f2275621..75827bbfb3ad 100644
@@ -816,6 +816,78 @@ rpmhcc: clock-controller {
 				clocks = <&xo_board>;
 			};
 		};
+
+		ufs_mem_hc: ufshc@1d84000 {
+			compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x3000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			iommus = <&apps_smmu 0xe0 0x0>;
+
+			clock-names =
+				"core_clk",
+				"bus_aggr_clk",
+				"iface_clk",
+				"core_clk_unipro",
+				"ref_clk",
+				"tx_lane0_sync_clk",
+				"rx_lane0_sync_clk",
+				"rx_lane1_sync_clk";
+			clocks =
+				<&gcc GCC_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_UFS_PHY_AHB_CLK>,
+				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				<&rpmhcc RPMH_CXO_CLK>,
+				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			freq-table-hz =
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<75000000 300000000>,
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<0 0>;
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sm8450-qmp-ufs-phy";
+			reg = <0 0x01d87000 0 0xe10>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref", "ref_aux", "qref";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+				 <&gcc GCC_UFS_0_CLKREF_EN>;
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+			status = "disabled";
+
+			ufs_mem_phy_lanes: lanes@1d87400 {
+				reg = <0 0x01d87400 0 0x108>,
+				      <0 0x01d87600 0 0x1e0>,
+				      <0 0x01d87c00 0 0x1dc>,
+				      <0 0x01d87800 0 0x108>,
+				      <0 0x01d87a00 0 0x1e0>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+			};
+		};
 	};
 
 	timer {
Signature · 1 line
2.31.1
author
#23 lore raw

PATCH 9/15 arm64: dts: qcom: sm8450-qrd: enable ufs nodes

In reply to Vinod Koul

Enable the UFS and phy node and add the regulators used by them.

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +21 -0
index 218eb3ce1ee5..3e65d662ab8c 100644
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8450.dtsi"
 
@@ -353,3 +354,23 @@ &tlmm {
 &uart7 {
 	status = "okay";
 };
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7b_2p5>;
+	vcc-max-microamp = <1100000>;
+	vccq-supply = <&vreg_l9b_1p2>;
+	vccq-max-microamp = <1200000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l5b_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+	vdda-max-microamp = <173000>;
+	vdda-pll-max-microamp = <24900>;
+};
Signature · 1 line
2.31.1
#24 lore raw

Re: [PATCH 09/15] arm64: dts: qcom: sm8450-qrd: enable ufs nodes

Quoted 12 lines · Vinod Koul

Enable the UFS and phy node and add the regulators used by them.

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 218eb3ce1ee5..3e65d662ab8c 100644

arch/arm64/boot/dts/qcom/sm8450-qrd.dts line 8

Quoted 4 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +1 -0
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>

This should probably go to the SoC DTSI, as it's generally used

in every DT if you have anything more than serial console working..

Konrad

author
#25 lore raw

Re: [PATCH 09/15] arm64: dts: qcom: sm8450-qrd: enable ufs nodes

Quoted 15 lines · Konrad Dybcio
Quoted 13 lines · Vinod Koul

Enable the UFS and phy node and add the regulators used by them.

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 218eb3ce1ee5..3e65d662ab8c 100644
@@ -5,6 +5,7 @@
 
Quoted 7 lines

arch/arm64/boot/dts/qcom/sm8450-qrd.dts line 8

Quoted 3 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +1 -0
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>

This should probably go to the SoC DTSI, as it's generally used

in every DT if you have anything more than serial console working..

But arent the gpios added in board dts typically? I am okay either way... Bjorn where would you like this to be..?
Seems like we have this is both board as well as SoC DTS

Quoted 3 lines

Konrad

Signature · 1 line
~Vinod
#26 lore raw

Re: [PATCH 09/15] arm64: dts: qcom: sm8450-qrd: enable ufs nodes

Quoted 22 lines · Vinod Koul
Quoted 21 lines · Konrad Dybcio
Quoted 12 lines · Vinod Koul

Enable the UFS and phy node and add the regulators used by them.

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 21 +++++++++++++++++++++
 1 file changed, 21 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 218eb3ce1ee5..3e65d662ab8c 100644

arch/arm64/boot/dts/qcom/sm8450-qrd.dts line 8

Quoted 4 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +1 -0
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>

This should probably go to the SoC DTSI, as it's generally used

Quoted 5 lines
Quoted 1 line

in every DT if you have anything more than serial console working..

But arent the gpios added in board dts typically? I am okay either way... Bjorn where would you like this to be..?
Seems like we have this is both board as well as SoC DTS

I like Konrad's suggestion of putting it in the dtsi, simply because it saves us from including it in every board file - where it will be needed.

Regards,
Bjorn

Quoted 6 lines
Quoted 3 lines

Konrad

Signature · 1 line
~Vinod
author
#27 lore raw

PATCH 10/15 arm64: dts: qcom: sm8450: add interconnect nodes

In reply to Vinod Koul

And the various interconnect nodes found in SM8450 SoC and use it for UFS controller.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 80 ++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +80 -0
index 75827bbfb3ad..4c7cdcea33fa 100644
@@ -6,6 +6,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-sm8450.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,sm8450.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 
 / {
@@ -573,6 +574,61 @@ uart7: serial@99c000 {
 			};
 		};
 
+		config_noc: interconnect@1500000 {
+			compatible = "qcom,sm8450-config-noc";
+			reg = <0 0x01500000 0 0x1c000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		mc_virt: interconnect@1580000 {
+			compatible = "qcom,sm8450-mc-virt";
+			reg = <0 0x01580000 0 0x1000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@1680000 {
+			reg = <0 0x01680000 0 0x1e200>;
+			compatible = "qcom,sm8450-system-noc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		pcie_noc: interconnect@16c0000 {
+			reg = <0 0x016c0000 0 0xe280>;
+			compatible = "qcom,sm8450-pcie-anoc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre1_noc: interconnect@16e0000 {
+			reg = <0 0x016e0000 0 0x1c080>;
+			compatible = "qcom,sm8450-aggre1-noc";
+			#interconnect-cells = <1>;
+			clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre2_noc: interconnect@1700000 {
+			reg = <0 0x01700000 0 0x31080>;
+			compatible = "qcom,sm8450-aggre2-noc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+			clocks = <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&rpmhcc RPMH_IPA_CLK>;
+		};
+
+		mmss_noc: interconnect@1740000 {
+			reg = <0 0x01740000 0 0x1f080>;
+			compatible = "qcom,sm8450-mmss-noc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x40000>;
@@ -817,6 +873,13 @@ rpmhcc: clock-controller {
 			};
 		};
 
+		gem_noc: interconnect@19100000 {
+			reg = <0 0x19100000 0 0xbb800>;
+			compatible = "qcom,sm8450-gem-noc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
 		ufs_mem_hc: ufshc@1d84000 {
 			compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
 				     "jedec,ufs-2.0";
@@ -833,6 +896,9 @@ ufs_mem_hc: ufshc@1d84000 {
 
 			iommus = <&apps_smmu 0xe0 0x0>;
 
+			interconnects = <&aggre1_noc MASTER_UFS_MEM &mc_virt SLAVE_EBI1>,
+					<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_UFS_MEM_CFG>;
+			interconnect-names = "ufs-ddr", "cpu-ufs";
 			clock-names =
 				"core_clk",
 				"bus_aggr_clk",
@@ -888,6 +954,20 @@ ufs_mem_phy_lanes: lanes@1d87400 {
 				#clock-cells = <0>;
 			};
 		};
+
+		nsp_noc: interconnect@320c0000 {
+			reg = <0 0x320c0000 0 0x10000>;
+			compatible = "qcom,sm8450-nsp-noc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		lpass_ag_noc: interconnect@3c40000 {
+			reg = <0 0x3c40000 0 0x17200>;
+			compatible = "qcom,sm8450-lpass-ag-noc";
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
 	};
 
 	timer {
Signature · 1 line
2.31.1
#28 lore raw

Re: [PATCH 10/15] arm64: dts: qcom: sm8450: add interconnect nodes

Quoted 31 lines · Vinod Koul

And the various interconnect nodes found in SM8450 SoC and use it for UFS controller.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 80 ++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +8 -0
index 75827bbfb3ad..4c7cdcea33fa 100644
@@ -6,6 +6,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-sm8450.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,sm8450.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 
 / {
@@ -573,6 +574,61 @@ uart7: serial@99c000 {
 			};
 		};
 
+		config_noc: interconnect@1500000 {
+			compatible = "qcom,sm8450-config-noc";
+			reg = <0 0x01500000 0 0x1c000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+

arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 593

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +10 -0
+		mc_virt: interconnect@1580000 {
+			compatible = "qcom,sm8450-mc-virt";
+			reg = <0 0x01580000 0 0x1000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@1680000 {
+			reg = <0 0x01680000 0 0x1e200>;
+			compatible = "qcom,sm8450-system-noc";

Compatible first, please

arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 600

Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		pcie_noc: interconnect@16c0000 {
+			reg = <0 0x016c0000 0 0xe280>;
+			compatible = "qcom,sm8450-pcie-anoc";

Ditto

arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 607

Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre1_noc: interconnect@16e0000 {
+			reg = <0 0x016e0000 0 0x1c080>;
+			compatible = "qcom,sm8450-aggre1-noc";

Ditto

arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 616

Quoted 9 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +9 -0
+			#interconnect-cells = <1>;
+			clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre2_noc: interconnect@1700000 {
+			reg = <0 0x01700000 0 0x31080>;
+			compatible = "qcom,sm8450-aggre2-noc";

Ditto

arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 627

Quoted 11 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +11 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+			clocks = <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&rpmhcc RPMH_IPA_CLK>;
+		};
+
+		mmss_noc: interconnect@1740000 {
+			reg = <0 0x01740000 0 0x1f080>;
+			compatible = "qcom,sm8450-mmss-noc";

Ditto

Quoted 8 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +4 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x40000>;

arch/arm64/boot/dts/qcom/sm8450.dtsi rpmhcc: clock-controller { · line 878

Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +3 -0
@@ -817,6 +873,13 @@ rpmhcc: clock-controller {
 			};
 		};
 
+		gem_noc: interconnect@19100000 {
+			reg = <0 0x19100000 0 0xbb800>;
+			compatible = "qcom,sm8450-gem-noc";

Ditto

Quoted 18 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
 		ufs_mem_hc: ufshc@1d84000 {
 			compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
 				     "jedec,ufs-2.0";
@@ -833,6 +896,9 @@ ufs_mem_hc: ufshc@1d84000 {
 
 			iommus = <&apps_smmu 0xe0 0x0>;
 
+			interconnects = <&aggre1_noc MASTER_UFS_MEM &mc_virt SLAVE_EBI1>,
+					<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_UFS_MEM_CFG>;
+			interconnect-names = "ufs-ddr", "cpu-ufs";
 			clock-names =
 				"core_clk",
 				"bus_aggr_clk",

arch/arm64/boot/dts/qcom/sm8450.dtsi ufs_mem_phy_lanes: lanes@1d87400 { · line 960

Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +4 -0
@@ -888,6 +954,20 @@ ufs_mem_phy_lanes: lanes@1d87400 {
 				#clock-cells = <0>;
 			};
 		};
+
+		nsp_noc: interconnect@320c0000 {
+			reg = <0 0x320c0000 0 0x10000>;
+			compatible = "qcom,sm8450-nsp-noc";

Ditto

arch/arm64/boot/dts/qcom/sm8450.dtsi ufs_mem_phy_lanes: lanes@1d87400 { · line 967

Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		lpass_ag_noc: interconnect@3c40000 {
+			reg = <0 0x3c40000 0 0x17200>;
+			compatible = "qcom,sm8450-lpass-ag-noc";

Ditto

arch/arm64/boot/dts/qcom/sm8450.dtsi ufs_mem_phy_lanes: lanes@1d87400 { · line 973

Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +3 -0
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
 	};
 
 	timer {

Konrad

author
#29 lore raw

Re: [PATCH 10/15] arm64: dts: qcom: sm8450: add interconnect nodes

Quoted 37 lines · Konrad Dybcio
Quoted 35 lines · Vinod Koul

And the various interconnect nodes found in SM8450 SoC and use it for UFS controller.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 80 ++++++++++++++++++++++++++++
 1 file changed, 80 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +12 -0
index 75827bbfb3ad..4c7cdcea33fa 100644
@@ -6,6 +6,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-sm8450.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,sm8450.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 
 / {
@@ -573,6 +574,61 @@ uart7: serial@99c000 {
 			};
 		};
 
+		config_noc: interconnect@1500000 {
+			compatible = "qcom,sm8450-config-noc";
+			reg = <0 0x01500000 0 0x1c000>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		mc_virt: interconnect@1580000 {
+			compatible = "qcom,sm8450-mc-virt";
+			reg = <0 0x01580000 0 0x1000>;
+			#interconnect-cells = <1>;
Quoted 8 lines

arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 593

Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +6 -0
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@1680000 {
+			reg = <0 0x01680000 0 0x1e200>;
+			compatible = "qcom,sm8450-system-noc";

Compatible first, please

will fix here and everywhere...

Signature · 1 line
~Vinod
author
#30 lore raw

PATCH 11/15 arm64: dts: qcom: sm8450: add spmi node

In reply to Vinod Koul

Add the spmi bus as found in the SM8450 SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +18 -0
index 4c7cdcea33fa..25d93a51ac19 100644
@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 {
 			interrupt-controller;
 		};
 
+		spmi_bus: spmi@c42d000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x0 0x0c400000 0x0 0x00003000>,
+			      <0x0 0x0c500000 0x0 0x00400000>,
+			      <0x0 0x0c440000 0x0 0x00080000>,
+			      <0x0 0x0c4c0000 0x0 0x00010000>,
+			      <0x0 0x0c42d000 0x0 0x00010000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
 		tlmm: pinctrl@f100000 {
 			compatible = "qcom,sm8450-tlmm";
 			reg = <0 0x0f100000 0 0x300000>;
Signature · 1 line
2.31.1
author
#32 lore raw

PATCH 12/15 arm64: dts: qcom: sm8450-qrd: include pmic files

In reply to Vinod Koul

SM8450 QRD platform has bunch of PMICs, include the common ones PM8350, PM8350b and PMR735b

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 3 +++
 1 file changed, 3 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +3 -0
index 3e65d662ab8c..48228888f500 100644
@@ -8,6 +8,9 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8450.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pmr735b.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SM8450 QRD";
Signature · 1 line
2.31.1
Reviewed-by on v1 12/15
#33 lore raw

Re: [PATCH 12/15] arm64: dts: qcom: sm8450-qrd: include pmic files

Quoted 14 lines · Vinod Koul

SM8450 QRD platform has bunch of PMICs, include the common ones PM8350, PM8350b and PMR735b

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 3 +++
 1 file changed, 3 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 3e65d662ab8c..48228888f500 100644

arch/arm64/boot/dts/qcom/sm8450-qrd.dts line 16

Quoted 9 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +3 -0
@@ -8,6 +8,9 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8450.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pmr735b.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SM8450 QRD";

Again, this could have gone into a single "add board DTS" patch, but this

works too, I guess..

Konrad

#34 lore raw

Re: [PATCH 12/15] arm64: dts: qcom: sm8450-qrd: include pmic files

Quoted 22 lines · Konrad Dybcio
Quoted 20 lines · Vinod Koul

SM8450 QRD platform has bunch of PMICs, include the common ones PM8350, PM8350b and PMR735b

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 3 +++
 1 file changed, 3 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +3 -0
index 3e65d662ab8c..48228888f500 100644
@@ -8,6 +8,9 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8450.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pmr735b.dtsi"
 
Quoted 7 lines

arch/arm64/boot/dts/qcom/sm8450-qrd.dts line 16

Quoted 3 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
 / {
 	model = "Qualcomm Technologies, Inc. SM8450 QRD";

Again, this could have gone into a single "add board DTS" patch, but this

works too, I guess..

I like that suggestion, putting the qrd.dts as a single patch at the end of the series would look nice.

Regards,
Bjorn

Quoted 6 lines

Konrad

author
#35 lore raw

Re: [PATCH 12/15] arm64: dts: qcom: sm8450-qrd: include pmic files

Quoted 29 lines · Bjorn Andersson
Quoted 27 lines · Konrad Dybcio
Quoted 14 lines · Vinod Koul

SM8450 QRD platform has bunch of PMICs, include the common ones PM8350, PM8350b and PMR735b

---
 arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 3 +++
 1 file changed, 3 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +0 -0
index 3e65d662ab8c..48228888f500 100644

arch/arm64/boot/dts/qcom/sm8450-qrd.dts line 16

Quoted 9 lines
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +3 -0
@@ -8,6 +8,9 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8450.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pmr735b.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SM8450 QRD";

Again, this could have gone into a single "add board DTS" patch, but this

Quoted 5 lines
Quoted 2 lines

works too, I guess..

I like that suggestion, putting the qrd.dts as a single patch at the end of the series would look nice.

I can do that.. I think I would do a dts patch but would keep regulator one separate..

Signature · 1 line
~Vinod
author
#36 lore raw

PATCH 13/15 arm64: dts: qcom: sm8450: Add rpmhpd node

In reply to Vinod Koul

From: Dmitry Baryshkov <[email protected]>

This adds RPMH power domain found in SM8450 SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +52 -0
index 25d93a51ac19..8f0819df8039 100644
@@ -7,6 +7,7 @@
 #include <dt-bindings/clock/qcom,gcc-sm8450.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/interconnect/qcom,sm8450.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 
 / {
@@ -889,6 +890,57 @@ rpmhcc: clock-controller {
 				clock-names = "xo";
 				clocks = <&xo_board>;
 			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sm8450-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
 		};
 
 		gem_noc: interconnect@19100000 {
Signature · 1 line
2.31.1
Reviewed-by on v1 13/15
#37 lore raw

Re: [PATCH 13/15] arm64: dts: qcom: sm8450: Add rpmhpd node

Quoted 9 lines · Vinod Koul

From: Dmitry Baryshkov <[email protected]>

This adds RPMH power domain found in SM8450 SoC

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++
 1 file changed, 52 insertions(+)

Konrad

author
#38 lore raw

PATCH 14/15 arm64: dts: qcom: sm8450: add cpufreq support

In reply to Vinod Koul

From: Vladimir Zapolskiy <[email protected]>

The change adds a description of a SM8450 cpufreq-epss controller and references to it from CPU nodes.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +27 -0
index 8f0819df8039..29c5abcfa074 100644
@@ -45,6 +45,7 @@ CPU0: cpu@0 {
 			next-level-cache = <&L2_0>;
 			power-domains = <&CPU_PD0>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_0: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -62,6 +63,7 @@ CPU1: cpu@100 {
 			next-level-cache = <&L2_100>;
 			power-domains = <&CPU_PD1>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_100: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -76,6 +78,7 @@ CPU2: cpu@200 {
 			next-level-cache = <&L2_200>;
 			power-domains = <&CPU_PD2>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_200: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -90,6 +93,7 @@ CPU3: cpu@300 {
 			next-level-cache = <&L2_300>;
 			power-domains = <&CPU_PD3>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
 			L2_300: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -104,6 +108,7 @@ CPU4: cpu@400 {
 			next-level-cache = <&L2_400>;
 			power-domains = <&CPU_PD4>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			L2_400: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -118,6 +123,7 @@ CPU5: cpu@500 {
 			next-level-cache = <&L2_500>;
 			power-domains = <&CPU_PD5>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			L2_500: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -133,6 +139,7 @@ CPU6: cpu@600 {
 			next-level-cache = <&L2_600>;
 			power-domains = <&CPU_PD6>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
 			L2_600: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -147,6 +154,7 @@ CPU7: cpu@700 {
 			next-level-cache = <&L2_700>;
 			power-domains = <&CPU_PD7>;
 			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 2>;
 			L2_700: l2-cache {
 			      compatible = "cache";
 			      next-level-cache = <&L3_0>;
@@ -170,7 +178,9 @@ core2 {
 				core3 {
 					cpu = <&CPU3>;
 				};
+			};
 
+			cluster1 {
 				core4 {
 					cpu = <&CPU4>;
 				};
@@ -182,7 +192,9 @@ core5 {
 				core6 {
 					cpu = <&CPU6>;
 				};
+			};
 
+			cluster2 {
 				core7 {
 					cpu = <&CPU7>;
 				};
@@ -943,6 +955,21 @@ rpmhpd_opp_turbo_l1: opp10 {
 
 		};
 
+		cpufreq_hw: cpufreq@17d91000 {
+			compatible = "qcom,sm8450-cpufreq-epss", "qcom,cpufreq-epss";
+			reg = <0 0x17d91000 0 0x1000>,
+			      <0 0x17d92000 0 0x1000>,
+			      <0 0x17d93000 0 0x1000>;
+			reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+			clock-names = "xo", "alternate";
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2";
+			#freq-domain-cells = <1>;
+		};
+
 		gem_noc: interconnect@19100000 {
 			reg = <0 0x19100000 0 0xbb800>;
 			compatible = "qcom,sm8450-gem-noc";
Signature · 1 line
2.31.1
#39 lore raw

Re: [PATCH 14/15] arm64: dts: qcom: sm8450: add cpufreq support

Quoted 11 lines · Vinod Koul

From: Vladimir Zapolskiy <[email protected]>

The change adds a description of a SM8450 cpufreq-epss controller and references to it from CPU nodes.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

[...]

Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +1 -0
+			cluster1 {
 				core4 {
 					cpu = <&CPU4>;
 				};

arch/arm64/boot/dts/qcom/sm8450.dtsi core5 { · line 200

Quoted 9 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +2 -0
@@ -182,7 +192,9 @@ core5 {
 				core6 {
 					cpu = <&CPU6>;
 				};
+			};
 
+			cluster2 {
 				core7 {
 					cpu = <&CPU7>;
 				};

Weren't DynamIQ-enabled SoCs supposed to be treated as single-cluster

from the Linux POV? Or has it changed again with the new chips?

[...]

Konrad

author
#40 lore raw

Re: [PATCH 14/15] arm64: dts: qcom: sm8450: add cpufreq support

Quoted 27 lines · Konrad Dybcio
Quoted 11 lines · Vinod Koul

From: Vladimir Zapolskiy <[email protected]>

The change adds a description of a SM8450 cpufreq-epss controller and references to it from CPU nodes.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 27 +++++++++++++++++++++++++++
 1 file changed, 27 insertions(+)

[...]

Quoted 11 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +2 -0
+			cluster1 {
 				core4 {
 					cpu = <&CPU4>;
 				};
@@ -182,7 +192,9 @@ core5 {
 				core6 {
 					cpu = <&CPU6>;
 				};
+			};
 
Quoted 8 lines

arch/arm64/boot/dts/qcom/sm8450.dtsi core5 { · line 200

Quoted 4 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +1 -0
+			cluster2 {
 				core7 {
 					cpu = <&CPU7>;
 				};

Weren't DynamIQ-enabled SoCs supposed to be treated as single-cluster

from the Linux POV? Or has it changed again with the new chips?

I discussed with Bjorn and yes we should have a single cluster for this. will fix

Signature · 1 line
~Vinod
author
#41 lore raw

PATCH 15/15 arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes

In reply to Vinod Koul

From: Dmitry Baryshkov <[email protected]>

Add device tree nodes for two i2c blocks: i2c13 and i2c14.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 64 ++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +64 -0
index 29c5abcfa074..40c739b842ac 100644
@@ -587,6 +587,44 @@ uart7: serial@99c000 {
 			};
 		};
 
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_default_state>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_default_state>;
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
 		config_noc: interconnect@1500000 {
 			compatible = "qcom,sm8450-config-noc";
 			reg = <0 0x01500000 0 0x1c000>;
@@ -687,6 +725,32 @@ tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 211>;
 			wakeup-parent = <&pdc>;
 
+			qup_i2c13_default_state: qup-i2c13-default-state {
+				mux {
+					pins = "gpio48", "gpio49";
+					function = "qup13";
+				};
+
+				config {
+					pins = "gpio48", "gpio49";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			qup_i2c14_default_state: qup-i2c14-default-state {
+				mux {
+					pins = "gpio52", "gpio53";
+					function = "qup14";
+				};
+
+				config {
+					pins = "gpio49", "gpio50";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
 			qup_uart7_default_state: qup-uart3-default-state {
 				rx {
 					pins = "gpio26";
Signature · 1 line
2.31.1
#42 lore raw

Re: [PATCH 15/15] arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes

Quoted 10 lines · Vinod Koul

From: Dmitry Baryshkov <[email protected]>

Add device tree nodes for two i2c blocks: i2c13 and i2c14.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 64 ++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

[...]

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +3 -0
 		config_noc: interconnect@1500000 {
 			compatible = "qcom,sm8450-config-noc";
 			reg = <0 0x01500000 0 0x1c000>;
@@ -687,6 +725,32 @@ tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 211>;
 			wakeup-parent = <&pdc>;
 
+			qup_i2c13_default_state: qup-i2c13-default-state {
+				mux {
+					pins = "gpio48", "gpio49";

arch/arm64/boot/dts/qcom/sm8450.dtsi tlmm: pinctrl@f100000 { · line 740

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +10 -0
+					function = "qup13";
+				};
+
+				config {
+					pins = "gpio48", "gpio49";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+

This should be collapsed into:

qup_i2c13_default_state: qup-i2c13-default-state {

        pins = "..."

        function = "..."

        drive-strength = <2>

        bias-pull-up;

};

And the same goes for the rest of the pins.

[...]

Konrad

author
#43 lore raw

Re: [PATCH 15/15] arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes

Quoted 45 lines · Konrad Dybcio
Quoted 10 lines · Vinod Koul

From: Dmitry Baryshkov <[email protected]>

Add device tree nodes for two i2c blocks: i2c13 and i2c14.

---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 64 ++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

[...]

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +3 -0
 		config_noc: interconnect@1500000 {
 			compatible = "qcom,sm8450-config-noc";
 			reg = <0 0x01500000 0 0x1c000>;
@@ -687,6 +725,32 @@ tlmm: pinctrl@f100000 {
 			gpio-ranges = <&tlmm 0 0 211>;
 			wakeup-parent = <&pdc>;
 
+			qup_i2c13_default_state: qup-i2c13-default-state {
+				mux {
+					pins = "gpio48", "gpio49";

arch/arm64/boot/dts/qcom/sm8450.dtsi tlmm: pinctrl@f100000 { · line 740

Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +10 -0
+					function = "qup13";
+				};
+
+				config {
+					pins = "gpio48", "gpio49";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+

This should be collapsed into:

qup_i2c13_default_state: qup-i2c13-default-state {

        pins = "..."

        function = "..."

Quoted 8 lines

        drive-strength = <2>

        bias-pull-up;

};

And the same goes for the rest of the pins.

Yeah that looks neater and done that now

Signature · 1 line
~Vinod