arm64: dts: qcom: Add support for SM8450 SoC and QRD board
v2 cover arm64: dts: qcom: Add support for SM8450 SoC and QRD board
Snapdragon 8 Gen 1 Mobile Platform [1] (SM8450) is the latest Qualcomm SoC announced today.
This series adds the DTS support including clocks, tlmm, smmu, regulators, ufs, interconnects, pmics and cpufreq found in the SM8450 QRD board.
[1]: https://www.qualcomm.com/products/snapdragon-8-gen-1-mobile-platform
Changes in v2:
- add the acks recieved
- move gpio header include to soc dts
- fix the uart node name
- rework pinctrol nodes
- drop cpu clusters
- fix consistency in nodes for reserved mem and icc
- Squash some patches into qrd dts patches
Dmitry Baryshkov (2):
arm64: dts: qcom: sm8450: Add rpmhpd node
arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes
Vinod Koul (10):
arm64: dts: qcom: Add base SM8450 DTSI
arm64: dts: qcom: sm8450: Add tlmm nodes
arm64: dts: qcom: sm8450: Add reserved memory nodes
arm64: dts: qcom: sm8450: add smmu nodes
arm64: dts: qcom: Add base SM8450 QRD DTS
arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes
arm64: dts: qcom: sm8450: add ufs nodes
arm64: dts: qcom: sm8450-qrd: enable ufs nodes
arm64: dts: qcom: sm8450: add interconnect nodes
arm64: dts: qcom: sm8450: add spmi node
Vladimir Zapolskiy (1):
arm64: dts: qcom: sm8450: add cpufreq support
arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 378 ++++++++ arch/arm64/boot/dts/qcom/sm8450.dtsi | 1125 +++++++++++++++++++++++ 3 files changed, 1504 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8450-qrd.dts create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
Signature · 1 line
2.31.1
PATCH v2 1/13 arm64: dts: qcom: Add base SM8450 DTSI
This add based DTSI for SM8450 SoC and includes base description of CPUs, GCC, RPMHCC, UART, interuupt-controller which helps to boot to shell with console on boards with this SoC
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 476 +++++++++++++++++++++++++++ 1 file changed, 476 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8450.dtsi
arch/arm64/boot/dts/qcom/sm8450.dtsi new file +476 -0
@@ -0,0 +1,476 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,gcc-sm8450.h> +#include <dt-bindings/clock/qcom,rpmh.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/soc/qcom,rpmh-rsc.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <76800000>; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + power-domains = <&CPU_PD0>; + power-domain-names = "psci"; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + power-domains = <&CPU_PD1>; + power-domain-names = "psci"; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + power-domains = <&CPU_PD2>; + power-domain-names = "psci"; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + power-domains = <&CPU_PD3>; + power-domain-names = "psci"; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + power-domains = <&CPU_PD4>; + power-domain-names = "psci"; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + power-domains = <&CPU_PD5>; + power-domain-names = "psci"; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + power-domains = <&CPU_PD6>; + power-domain-names = "psci"; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo780"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + power-domains = <&CPU_PD7>; + power-domain-names = "psci"; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + + core2 { + cpu = <&CPU2>; + }; + + core3 { + cpu = <&CPU3>; + }; + + core4 { + cpu = <&CPU4>; + }; + + core5 { + cpu = <&CPU5>; + }; + + core6 { + cpu = <&CPU6>; + }; + + core7 { + cpu = <&CPU7>; + }; + }; + }; + + idle-states { + entry-method = "psci"; + + LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + idle-state-name = "silver-rail-power-collapse"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <274>; + exit-latency-us = <480>; + min-residency-us = <3934>; + local-timer-stop; + }; + + BIG_CPU_SLEEP_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + idle-state-name = "gold-rail-power-collapse"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <327>; + exit-latency-us = <1502>; + min-residency-us = <4488>; + local-timer-stop; + }; + }; + + domain-idle-states { + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "domain-idle-state"; + idle-state-name = "cluster-l3-off"; + arm,psci-suspend-param = <0x4100c344>; + entry-latency-us = <584>; + exit-latency-us = <2332>; + min-residency-us = <6118>; + local-timer-stop; + }; + + CLUSTER_SLEEP_1: cluster-sleep-1 { + compatible = "domain-idle-state"; + idle-state-name = "cluster-power-collapse"; + arm,psci-suspend-param = <0x4100c344>; + entry-latency-us = <2893>; + exit-latency-us = <4023>; + min-residency-us = <9987>; + local-timer-stop; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8450", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@a0000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0xa0000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + + CPU_PD0: cpu0 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD1: cpu1 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD2: cpu2 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD3: cpu3 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD4: cpu4 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD5: cpu5 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD6: cpu6 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD7: cpu7 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CLUSTER_PD: cpu-cluster0 { + #power-domain-cells = <0>; + domain-idle-states = <&CLUSTER_SLEEP_0>; + }; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8450"; + reg = <0x0 0x00100000 0x0 0x1f4200>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; + }; + + qupv3_id_0: geniqup@9c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x009c0000 0x0 0x2000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart7: serial@99c000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x0099c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x0 0x01f40000 0x0 0x40000>; + #hwlock-cells = <1>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sm8450-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>; + qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>, + <94 609 31>, <125 63 1>, <126 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + intc: interrupt-controller@17100000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + #redistributor-regions = <1>; + redistributor-stride = <0x0 0x40000>; + reg = <0x0 0x17100000 0x0 0x10000>, /* GICD */ + <0x0 0x17180000 0x0 0x200000>; /* GICR * 8 */ + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@17420000 { + compatible = "arm,armv7-timer-mem"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + reg = <0x0 0x17420000 0x0 0x1000>; + clock-frequency = <19200000>; + + frame@17421000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17421000 0x0 0x1000>, + <0x0 0x17422000 0x0 0x1000>; + }; + + frame@17423000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17423000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17425000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17425000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17427000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17427000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17429000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x17429000 0x0 0x1000>; + status = "disabled"; + }; + + frame@1742b000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x1742b000 0x0 0x1000>; + status = "disabled"; + }; + + frame@1742d000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0 0x1742d000 0x0 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@17a00000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x0 0x17a00000 0x0 0x10000>, + <0x0 0x17a10000 0x0 0x10000>, + <0x0 0x17a20000 0x0 0x10000>, + <0x0 0x17a30000 0x0 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2", "drv-3"; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = <ACTIVE_TCS 3>, <SLEEP_TCS 2>, + <WAKE_TCS 2>, <CONTROL_TCS 0>; + + apps_bcm_voter: bcm-voter { + compatible = "qcom,bcm-voter"; + }; + + rpmhcc: clock-controller { + compatible = "qcom,sm8450-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>; + clock-frequency = <19200000>; + }; +};
Signature · 1 line
2.31.1
PATCH v2 2/13 arm64: dts: qcom: sm8450: Add tlmm nodes
In reply to Vinod KoulAdd tlmm node found in SM8450 SoC and uart pin configuration
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +28 -0
@@ -343,6 +343,8 @@ uart7: serial@99c000 { reg = <0 0x0099c000 0 0x4000>; clock-names = "se"; clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>; interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>;
@@ -366,6 +368,32 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + tlmm: pinctrl@f100000 { + compatible = "qcom,sm8450-tlmm"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 211>; + wakeup-parent = <&pdc>; + + qup_uart7_rx: qup-uart7-rx { + pins = "gpio26"; + function = "qup7"; + drive-strength = <2>; + bias-disable; + }; + + qup_uart7_tx: qup-uart7-tx { + pins = "gpio27"; + function = "qup7"; + drive-strength = <2>; + bias-disable; + }; + }; + intc: interrupt-controller@17100000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>;
Signature · 1 line
2.31.1
PATCH v2 3/13 arm64: dts: qcom: sm8450: Add reserved memory nodes
In reply to Vinod KoulAdd the reserved memory nodes for SM8450. This is based on the downstream documentation.
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 221 +++++++++++++++++++++++++++ 1 file changed, 221 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +221 -0
@@ -310,6 +310,227 @@ CLUSTER_PD: cpu-cluster0 { }; }; + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@80000000 { + reg = <0x0 0x80000000 0x0 0x600000>; + no-map; + }; + + xbl_dt_log_mem: memory@80600000 { + reg = <0x0 0x80600000 0x0 0x40000>; + no-map; + }; + + xbl_ramdump_mem: memory@80640000 { + reg = <0x0 0x80640000 0x0 0x180000>; + no-map; + }; + + xbl_sc_mem: memory@807c0000 { + reg = <0x0 0x807c0000 0x0 0x40000>; + no-map; + }; + + aop_image_mem: memory@80800000 { + reg = <0x0 0x80800000 0x0 0x60000>; + no-map; + }; + + aop_cmd_db_mem: memory@80860000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x80860000 0x0 0x20000>; + no-map; + }; + + aop_config_mem: memory@80880000 { + reg = <0x0 0x80880000 0x0 0x20000>; + no-map; + }; + + tme_crash_dump_mem: memory@808a0000 { + reg = <0x0 0x808a0000 0x0 0x40000>; + no-map; + }; + + tme_log_mem: memory@808e0000 { + reg = <0x0 0x808e0000 0x0 0x4000>; + no-map; + }; + + uefi_log_mem: memory@808e4000 { + reg = <0x0 0x808e4000 0x0 0x10000>; + no-map; + }; + + /* secdata region can be reused by apps */ + smem: memory@80900000 { + compatible = "qcom,smem"; + reg = <0x0 0x80900000 0x0 0x200000>; + hwlocks = <&tcsr_mutex 3>; + no-map; + }; + + cpucp_fw_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@80c00000 { + reg = <0x0 0x80c00000 0x0 0x4600000>; + no-map; + }; + + camera_mem: memory@85200000 { + reg = <0x0 0x85200000 0x0 0x500000>; + no-map; + }; + + video_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x700000>; + no-map; + }; + + adsp_mem: memory@85e00000 { + reg = <0x0 0x85e00000 0x0 0x2100000>; + no-map; + }; + + slpi_mem: memory@88000000 { + reg = <0x0 0x88000000 0x0 0x1900000>; + no-map; + }; + + cdsp_mem: memory@89900000 { + reg = <0x0 0x89900000 0x0 0x2000000>; + no-map; + }; + + ipa_fw_mem: memory@8b900000 { + reg = <0x0 0x8b900000 0x0 0x10000>; + no-map; + }; + + ipa_gsi_mem: memory@8b910000 { + reg = <0x0 0x8b910000 0x0 0xa000>; + no-map; + }; + + gpu_micro_code_mem: memory@8b91a000 { + reg = <0x0 0x8b91a000 0x0 0x2000>; + no-map; + }; + + spss_region_mem: memory@8ba00000 { + reg = <0x0 0x8ba00000 0x0 0x180000>; + no-map; + }; + + /* First part of the "SPU secure shared memory" region */ + spu_tz_shared_mem: memory@8bb80000 { + reg = <0x0 0x8bb80000 0x0 0x60000>; + no-map; + }; + + /* Second part of the "SPU secure shared memory" region */ + spu_modem_shared_mem: memory@8bbe0000 { + reg = <0x0 0x8bbe0000 0x0 0x20000>; + no-map; + }; + + mpss_mem: memory@8bc00000 { + reg = <0x0 0x8bc00000 0x0 0x13200000>; + no-map; + }; + + cvp_mem: memory@9ee00000 { + reg = <0x0 0x9ee00000 0x0 0x700000>; + no-map; + }; + + global_sync_mem: memory@a6f00000 { + reg = <0x0 0xa6f00000 0x0 0x100000>; + no-map; + }; + + /* uefi region can be reused by APPS */ + + /* Linux kernel image is loaded at 0xa0000000 */ + + oem_vm_mem: memory@bb000000 { + reg = <0x0 0xbb000000 0x0 0x5000000>; + no-map; + }; + + mte_mem: memory@c0000000 { + reg = <0x0 0xc0000000 0x0 0x20000000>; + no-map; + }; + + qheebsp_reserved_mem: memory@e0000000 { + reg = <0x0 0xe0000000 0x0 0x600000>; + no-map; + }; + + cpusys_vm_mem: memory@e0600000 { + reg = <0x0 0xe0600000 0x0 0x400000>; + no-map; + }; + + hyp_reserved_mem: memory@e0a00000 { + reg = <0x0 0xe0a00000 0x0 0x100000>; + no-map; + }; + + trust_ui_vm_mem: memory@e0b00000 { + reg = <0x0 0xe0b00000 0x0 0x4af3000>; + no-map; + }; + + trust_ui_vm_qrtr: memory@e55f3000 { + reg = <0x0 0xe55f3000 0x0 0x9000>; + no-map; + }; + + trust_ui_vm_vblk0_ring: memory@e55fc000 { + reg = <0x0 0xe55fc000 0x0 0x4000>; + no-map; + }; + + trust_ui_vm_swiotlb: memory@e5600000 { + reg = <0x0 0xe5600000 0x0 0x100000>; + no-map; + }; + + tz_stat_mem: memory@e8800000 { + reg = <0x0 0xe8800000 0x0 0x100000>; + no-map; + }; + + tags_mem: memory@e8900000 { + reg = <0x0 0xe8900000 0x0 0x1200000>; + no-map; + }; + + qtee_mem: memory@e9b00000 { + reg = <0x0 0xe9b00000 0x0 0x500000>; + no-map; + }; + + trusted_apps_mem: memory@ea000000 { + reg = <0x0 0xea000000 0x0 0x3900000>; + no-map; + }; + + trusted_apps_ext_mem: memory@ed900000 { + reg = <0x0 0xed900000 0x0 0x3b00000>; + no-map; + }; + }; + soc: soc@0 { #address-cells = <2>; #size-cells = <2>;
Signature · 1 line
2.31.1
PATCH v2 4/13 arm64: dts: qcom: sm8450: add smmu nodes
In reply to Vinod KoulAdd the apps smmu node as found in the SM8450 SoC
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 103 +++++++++++++++++++++++++++ 1 file changed, 103 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +103 -0
@@ -615,6 +615,109 @@ qup_uart7_tx: qup-uart7-tx { }; }; + apps_smmu: iommu@15000000 { + compatible = "qcom,sm8450-smmu-500", "arm,mmu-500"; + reg = <0 0x15000000 0 0x100000>; + #iommu-cells = <2>; + #global-interrupts = <2>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>; + }; + intc: interrupt-controller@17100000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>;
Signature · 1 line
2.31.1
PATCH v2 5/13 arm64: dts: qcom: Add base SM8450 QRD DTS
In reply to Vinod KoulAdd DTS for Qualcomm QRD platform which uses SM8450 SoC. This also includes the pmic files and marks the tlmm reserved pins
--- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 36 +++++++++++++++++++++++++ 2 files changed, 37 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8450-qrd.dts
arch/arm64/boot/dts/qcom/Makefile +1 -0
@@ -107,3 +107,4 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx203.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-sony-xperia-edo-pdx206.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8450-qrd.dtb
arch/arm64/boot/dts/qcom/sm8450-qrd.dts new file +36 -0
@@ -0,0 +1,36 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2021, Linaro Limited + */ + +/dts-v1/; + +#include "sm8450.dtsi" +#include "pm8350.dtsi" +#include "pm8350b.dtsi" +#include "pmr735b.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SM8450 QRD"; + compatible = "qcom,sm8450-qrd", "qcom,sm8450"; + + aliases { + serial0 = &uart7; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <28 4>, <36 4>; +}; + +&uart7 { + status = "okay"; +};
Signature · 1 line
2.31.1
kernel test robot
build botRe: [PATCH v2 05/13] arm64: dts: qcom: Add base SM8450 QRD DTS
I love your patch! Yet something to improve:
Hi Vinod,
I love your patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on v5.16-rc4]
[cannot apply to next-20211208]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Vinod-Koul/arm64-dts-qcom-Add-support-for-SM8450-SoC-and-QRD-board/20211209-183713 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm64-randconfig-r032-20211207 (https://download.01.org/0day-ci/archive/20211210/202112100623.XZwPiDOL-lkp(a)intel.com/config) compiler: aarch64-linux-gcc (GCC) 11.2.0
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/636d2456715b3aba9cf1fa47931c6e381ca62e00
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Vinod-Koul/arm64-dts-qcom-Add-support-for-SM8450-SoC-and-QRD-board/20211209-183713 git checkout 636d2456715b3aba9cf1fa47931c6e381ca62e00
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
All errors (new ones prefixed by >>):
In file included from arch/arm64/boot/dts/qcom/sm8450-qrd.dts:8:
>> arch/arm64/boot/dts/qcom/sm8450.dtsi:7:10: fatal error: dt-bindings/clock/qcom,gcc-sm8450.h: No such file or directory
7 | #include <dt-bindings/clock/qcom,gcc-sm8450.h>
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~compilation terminated.
vim +7 arch/arm64/boot/dts/qcom/sm8450.dtsi
244741584ca1ceb Vinod Koul 2021-12-09 @7 #include <dt-bindings/clock/qcom,gcc-sm8450.h> 244741584ca1ceb Vinod Koul 2021-12-09 8 #include <dt-bindings/clock/qcom,rpmh.h> 244741584ca1ceb Vinod Koul 2021-12-09 9 #include <dt-bindings/gpio/gpio.h> 244741584ca1ceb Vinod Koul 2021-12-09 10 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
244741584ca1ceb Vinod Koul 2021-12-09 11
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org
kernel test robot
build botRe: [PATCH v2 05/13] arm64: dts: qcom: Add base SM8450 QRD DTS
In reply to Vinod KoulI love your patch! Yet something to improve:
Hi Vinod,
I love your patch! Yet something to improve:
[auto build test ERROR on robh/for-next]
[also build test ERROR on v5.16-rc4]
[cannot apply to next-20211208]
[If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Vinod-Koul/arm64-dts-qcom-Add-support-for-SM8450-SoC-and-QRD-board/20211209-183713 base: https://git.kernel.org/pub/scm/linux/kernel/git/robh/linux.git for-next config: arm64-randconfig-r022-20211207 (https://download.01.org/0day-ci/archive/20211210/202112101124.H3KNjjaf-lkp(a)intel.com/config) compiler: clang version 14.0.0 (https://github.com/llvm/llvm-project 097a1cb1d5ebb3a0ec4bcaed8ba3ff6a8e33c00a)
reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross chmod +x ~/bin/make.cross
# install arm64 cross compiling tool for clang build
# apt-get install binutils-aarch64-linux-gnu
# https://github.com/0day-ci/linux/commit/636d2456715b3aba9cf1fa47931c6e381ca62e00
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Vinod-Koul/arm64-dts-qcom-Add-support-for-SM8450-SoC-and-QRD-board/20211209-183713 git checkout 636d2456715b3aba9cf1fa47931c6e381ca62e00
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=clang make.cross W=1 O=build_dir ARCH=arm64 SHELL=/bin/bash
If you fix the issue, kindly add following tag as appropriate
All errors (new ones prefixed by >>):
In file included from arch/arm64/boot/dts/qcom/sm8450-qrd.dts:8:
>> arch/arm64/boot/dts/qcom/sm8450.dtsi:7:10: fatal error: 'dt-bindings/clock/qcom,gcc-sm8450.h' file not found
#include <dt-bindings/clock/qcom,gcc-sm8450.h>
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~1 error generated.
vim +7 arch/arm64/boot/dts/qcom/sm8450.dtsi
244741584ca1ceb Vinod Koul 2021-12-09 @7 #include <dt-bindings/clock/qcom,gcc-sm8450.h> 244741584ca1ceb Vinod Koul 2021-12-09 8 #include <dt-bindings/clock/qcom,rpmh.h> 244741584ca1ceb Vinod Koul 2021-12-09 9 #include <dt-bindings/gpio/gpio.h> 244741584ca1ceb Vinod Koul 2021-12-09 10 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
244741584ca1ceb Vinod Koul 2021-12-09 11
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org
PATCH v2 6/13 arm64: dts: qcom: sm8450-qrd: Add rpmh regulator nodes
In reply to Vinod KoulAdd the RPMH regulators found in QRD-SM8450 platform
--- arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 322 ++++++++++++++++++++++++ 1 file changed, 322 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +322 -0
@@ -5,6 +5,7 @@ /dts-v1/; +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> #include "sm8450.dtsi" #include "pm8350.dtsi" #include "pm8350b.dtsi"
@@ -21,6 +22,327 @@ aliases { chosen { stdout-path = "serial0:115200n8"; }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + pm8350-rpmh-regulators { + compatible = "qcom,pm8350-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + + vdd-l1-l4-supply = <&vreg_s11b_0p95>; + vdd-l2-l7-supply = <&vreg_bob>; + vdd-l3-l5-supply = <&vreg_bob>; + vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>; + vdd-l8-supply = <&vreg_s2h_0p95>; + + vreg_s10b_1p8: smps10 { + regulator-name = "vreg_s10b_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_s11b_0p95: smps11 { + regulator-name = "vreg_s11b_0p95"; + regulator-min-microvolt = <848000>; + regulator-max-microvolt = <1104000>; + }; + + vreg_s12b_1p25: smps12 { + regulator-name = "vreg_s12b_1p25"; + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1400000>; + }; + + vreg_l1b_0p91: ldo1 { + regulator-name = "vreg_l1b_0p91"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b_3p07: ldo2 { + regulator-name = "vreg_l2b_3p07"; + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3b_0p9: ldo3 { + regulator-name = "vreg_l3b_0p9"; + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <904000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5b_0p88: ldo5 { + regulator-name = "vreg_l5b_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <888000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b_1p2: ldo6 { + regulator-name = "vreg_l6b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b_2p5: ldo7 { + regulator-name = "vreg_l7b_2p5"; + regulator-min-microvolt = <2504000>; + regulator-max-microvolt = <2504000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b_1p2: ldo9 { + regulator-name = "vreg_l9b_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8350c-rpmh-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + + vdd-l1-l12-supply = <&vreg_bob>; + vdd-l2-l8-supply = <&vreg_bob>; + vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; + vdd-l6-l9-l11-supply = <&vreg_bob>; + + vdd-bob-supply = <&vph_pwr>; + + vreg_s1c_1p86: smps1 { + regulator-name = "vreg_s1c_1p86"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2024000>; + }; + + vreg_s10c_1p05: smps10 { + regulator-name = "vreg_s10c_1p05"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1100000>; + }; + + vreg_bob: bob { + regulator-name = "vreg_bob"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-name = "vreg_l1c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_3p0: ldo3 { + regulator-name = "vreg_l3c_3p0"; + regulator-min-microvolt = <3296000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c_1p8: ldo4 { + regulator-name = "vreg_l4c_1p8"; + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-name = "vreg_l5c_1p8"; + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c_1p8: ldo6 { + regulator-name = "vreg_l6c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-name = "vreg_l7c_3p0"; + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-name = "vreg_l8c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p96: ldo9 { + regulator-name = "vreg_l9c_2p96"; + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12c_1p8: ldo12 { + regulator-name = "vreg_l12c_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1968000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13c_3p0: ldo13 { + regulator-name = "vreg_l13c_3p0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm8450-rpmh-regulators { + compatible = "qcom,pm8450-rpmh-regulators"; + qcom,pmic-id = "h"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + + vdd-l2-supply = <&vreg_bob>; + vdd-l3-supply = <&vreg_bob>; + vdd-l4-supply = <&vreg_bob>; + + vreg_s2h_0p95: smps2 { + regulator-name = "vreg_s2h_0p95"; + regulator-min-microvolt = <848000>; + regulator-max-microvolt = <1104000>; + }; + + vreg_s3h_0p5: smps3 { + regulator-name = "vreg_s3h_0p5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <500000>; + }; + + vreg_l2h_0p91: ldo2 { + regulator-name = "vreg_l2h_0p91"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3h_0p91: ldo3 { + regulator-name = "vreg_l3h_0p91"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + }; + + pmr735a-rpmh-regulators { + compatible = "qcom,pmr735a-rpmh-regulators"; + qcom,pmic-id = "e"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + + vdd-l1-l2-supply = <&vreg_s2e_0p85>; + vdd-l3-supply = <&vreg_s1e_1p25>; + vdd-l4-supply = <&vreg_s1c_1p86>; + vdd-l5-l6-supply = <&vreg_s1c_1p86>; + vdd-l7-bob-supply = <&vreg_bob>; + + vreg_s1e_1p25: smps1 { + regulator-name = "vreg_s1e_1p25"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1296000>; + }; + + vreg_s2e_0p85: smps2 { + regulator-name = "vreg_s2e_0p85"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1040000>; + }; + + vreg_l1e_0p8: ldo1 { + regulator-name = "vreg_l1e_0p8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l2e_0p8: ldo2 { + regulator-name = "vreg_l2e_0p8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + }; + + vreg_l3e_1p2: ldo3 { + regulator-name = "vreg_l3e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vreg_l4e_1p7: ldo4 { + regulator-name = "vreg_l4e_1p7"; + regulator-min-microvolt = <1776000>; + regulator-max-microvolt = <1776000>; + }; + + vreg_l5e_0p88: ldo5 { + regulator-name = "vreg_l5e_0p88"; + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + }; + + vreg_l6e_1p2: ldo6 { + regulator-name = "vreg_l6e_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + }; }; &qupv3_id_0 {
Signature · 1 line
2.31.1
PATCH v2 7/13 arm64: dts: qcom: sm8450: add ufs nodes
In reply to Vinod KoulAdd the UFS and QMP PHY node for SM8450 SoC
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 72 ++++++++++++++++++++++++++++ 1 file changed, 72 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +72 -0
@@ -815,6 +815,78 @@ rpmhcc: clock-controller { clocks = <&xo_board>; }; }; + + ufs_mem_hc: ufshc@1d84000 { + compatible = "qcom,sm8450-ufshc", "qcom,ufshc", + "jedec,ufs-2.0"; + reg = <0 0x01d84000 0 0x3000>; + interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>; + phys = <&ufs_mem_phy_lanes>; + phy-names = "ufsphy"; + lanes-per-direction = <2>; + #reset-cells = <1>; + resets = <&gcc GCC_UFS_PHY_BCR>; + reset-names = "rst"; + + power-domains = <&gcc UFS_PHY_GDSC>; + + iommus = <&apps_smmu 0xe0 0x0>; + + clock-names = + "core_clk", + "bus_aggr_clk", + "iface_clk", + "core_clk_unipro", + "ref_clk", + "tx_lane0_sync_clk", + "rx_lane0_sync_clk", + "rx_lane1_sync_clk"; + clocks = + <&gcc GCC_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_UFS_PHY_AHB_CLK>, + <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, + <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, + <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>; + freq-table-hz = + <75000000 300000000>, + <0 0>, + <0 0>, + <75000000 300000000>, + <75000000 300000000>, + <0 0>, + <0 0>, + <0 0>; + status = "disabled"; + }; + + ufs_mem_phy: phy@1d87000 { + compatible = "qcom,sm8450-qmp-ufs-phy"; + reg = <0 0x01d87000 0 0xe10>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clock-names = "ref", "ref_aux", "qref"; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&gcc GCC_UFS_PHY_PHY_AUX_CLK>, + <&gcc GCC_UFS_0_CLKREF_EN>; + + resets = <&ufs_mem_hc 0>; + reset-names = "ufsphy"; + status = "disabled"; + + ufs_mem_phy_lanes: lanes@1d87400 { + reg = <0 0x01d87400 0 0x108>, + <0 0x01d87600 0 0x1e0>, + <0 0x01d87c00 0 0x1dc>, + <0 0x01d87800 0 0x108>, + <0 0x01d87a00 0 0x1e0>; + #phy-cells = <0>; + #clock-cells = <0>; + }; + }; }; timer {
Signature · 1 line
2.31.1
PATCH v2 8/13 arm64: dts: qcom: sm8450-qrd: enable ufs nodes
In reply to Vinod KoulEnable the UFS and phy node and add the regulators used by them.
--- arch/arm64/boot/dts/qcom/sm8450-qrd.dts | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm64/boot/dts/qcom/sm8450-qrd.dts +20 -0
@@ -356,3 +356,23 @@ &tlmm { &uart7 { status = "okay"; }; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l7b_2p5>; + vcc-max-microamp = <1100000>; + vccq-supply = <&vreg_l9b_1p2>; + vccq-max-microamp = <1200000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l5b_0p88>; + vdda-pll-supply = <&vreg_l6b_1p2>; + vdda-max-microamp = <173000>; + vdda-pll-max-microamp = <24900>; +};
Signature · 1 line
2.31.1
PATCH v2 9/13 arm64: dts: qcom: sm8450: add interconnect nodes
In reply to Vinod KoulAnd the various interconnect nodes found in SM8450 SoC and use it for UFS controller.
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 80 ++++++++++++++++++++++++++++ 1 file changed, 80 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +80 -0
@@ -7,6 +7,7 @@ #include <dt-bindings/clock/qcom,gcc-sm8450.h> #include <dt-bindings/clock/qcom,rpmh.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interconnect/qcom,sm8450.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> / {
@@ -573,6 +574,61 @@ uart7: serial@99c000 { }; }; + config_noc: interconnect@1500000 { + compatible = "qcom,sm8450-config-noc"; + reg = <0 0x01500000 0 0x1c000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mc_virt: interconnect@1580000 { + compatible = "qcom,sm8450-mc-virt"; + reg = <0 0x01580000 0 0x1000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + system_noc: interconnect@1680000 { + compatible = "qcom,sm8450-system-noc"; + reg = <0 0x01680000 0 0x1e200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + pcie_noc: interconnect@16c0000 { + compatible = "qcom,sm8450-pcie-anoc"; + reg = <0 0x016c0000 0 0xe280>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre1_noc: interconnect@16e0000 { + compatible = "qcom,sm8450-aggre1-noc"; + reg = <0 0x016e0000 0 0x1c080>; + #interconnect-cells = <1>; + clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre2_noc: interconnect@1700000 { + compatible = "qcom,sm8450-aggre2-noc"; + reg = <0 0x01700000 0 0x31080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + clocks = <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>, + <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>, + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&rpmhcc RPMH_IPA_CLK>; + }; + + mmss_noc: interconnect@1740000 { + compatible = "qcom,sm8450-mmss-noc"; + reg = <0 0x01740000 0 0x1f080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x0 0x01f40000 0x0 0x40000>;
@@ -816,6 +872,13 @@ rpmhcc: clock-controller { }; }; + gem_noc: interconnect@19100000 { + compatible = "qcom,sm8450-gem-noc"; + reg = <0 0x19100000 0 0xbb800>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + ufs_mem_hc: ufshc@1d84000 { compatible = "qcom,sm8450-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
@@ -832,6 +895,9 @@ ufs_mem_hc: ufshc@1d84000 { iommus = <&apps_smmu 0xe0 0x0>; + interconnects = <&aggre1_noc MASTER_UFS_MEM &mc_virt SLAVE_EBI1>, + <&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_UFS_MEM_CFG>; + interconnect-names = "ufs-ddr", "cpu-ufs"; clock-names = "core_clk", "bus_aggr_clk",
@@ -887,6 +953,20 @@ ufs_mem_phy_lanes: lanes@1d87400 { #clock-cells = <0>; }; }; + + nsp_noc: interconnect@320c0000 { + compatible = "qcom,sm8450-nsp-noc"; + reg = <0 0x320c0000 0 0x10000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + lpass_ag_noc: interconnect@3c40000 { + compatible = "qcom,sm8450-lpass-ag-noc"; + reg = <0 0x3c40000 0 0x17200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; }; timer {
Signature · 1 line
2.31.1
Re: [PATCH v2 09/13] arm64: dts: qcom: sm8450: add interconnect nodes
Quoted 7 lines · Vinod Koul
And the various interconnect nodes found in SM8450 SoC and use it for UFS controller.
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 80 ++++++++++++++++++++++++++++ 1 file changed, 80 insertions(+)
Konrad
Re: [PATCH v2 09/13] arm64: dts: qcom: sm8450: add interconnect nodes
In reply to Vinod KoulHi Vinod,
Quoted 24 lines · Vinod Koul
And the various interconnect nodes found in SM8450 SoC and use it for UFS controller.
Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 80 ++++++++++++++++++++++++++++ 1 file changed, 80 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +1
-0@@ -7,6 +7,7 @@ #include <dt-bindings/clock/qcom,gcc-sm8450.h> #include <dt-bindings/clock/qcom,rpmh.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interconnect/qcom,sm8450.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> / {@@ -573,6 +574,61 @@ uart7: serial@99c000 { }; };
arch/arm64/boot/dts/qcom/sm8450.dtsi uart7: serial@99c000 { · line 586
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +10
-0+ config_noc: interconnect@1500000 { + compatible = "qcom,sm8450-config-noc"; + reg = <0 0x01500000 0 0x1c000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + mc_virt: interconnect@1580000 { + compatible = "qcom,sm8450-mc-virt"; + reg = <0 0x01580000 0 0x1000>;
Is there really a register space for this noc?
Quoted 75 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +55
-0+ #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + system_noc: interconnect@1680000 { + compatible = "qcom,sm8450-system-noc"; + reg = <0 0x01680000 0 0x1e200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + pcie_noc: interconnect@16c0000 { + compatible = "qcom,sm8450-pcie-anoc"; + reg = <0 0x016c0000 0 0xe280>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre1_noc: interconnect@16e0000 { + compatible = "qcom,sm8450-aggre1-noc"; + reg = <0 0x016e0000 0 0x1c080>; + #interconnect-cells = <1>; + clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + aggre2_noc: interconnect@1700000 { + compatible = "qcom,sm8450-aggre2-noc"; + reg = <0 0x01700000 0 0x31080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + clocks = <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>, + <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>, + <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>, + <&rpmhcc RPMH_IPA_CLK>; + }; + + mmss_noc: interconnect@1740000 { + compatible = "qcom,sm8450-mmss-noc"; + reg = <0 0x01740000 0 0x1f080>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x0 0x01f40000 0x0 0x40000>;@@ -816,6 +872,13 @@ rpmhcc: clock-controller { }; }; + gem_noc: interconnect@19100000 { + compatible = "qcom,sm8450-gem-noc"; + reg = <0 0x19100000 0 0xbb800>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + ufs_mem_hc: ufshc@1d84000 { compatible = "qcom,sm8450-ufshc", "qcom,ufshc", "jedec,ufs-2.0";@@ -832,6 +895,9 @@ ufs_mem_hc: ufshc@1d84000 { iommus = <&apps_smmu 0xe0 0x0>; + interconnects = <&aggre1_noc MASTER_UFS_MEM &mc_virt SLAVE_EBI1>, + <&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_UFS_MEM_CFG>; + interconnect-names = "ufs-ddr", "cpu-ufs"; clock-names = "core_clk", "bus_aggr_clk",@@ -887,6 +953,20 @@ ufs_mem_phy_lanes: lanes@1d87400 { #clock-cells = <0>; };
arch/arm64/boot/dts/qcom/sm8450.dtsi ufs_mem_phy_lanes: lanes@1d87400 { · line 964
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +9
-0}; + + nsp_noc: interconnect@320c0000 { + compatible = "qcom,sm8450-nsp-noc"; + reg = <0 0x320c0000 0 0x10000>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; + + lpass_ag_noc: interconnect@3c40000 {
Nit: This should move up, if we want to order them by node address.
arch/arm64/boot/dts/qcom/sm8450.dtsi ufs_mem_phy_lanes: lanes@1d87400 { · line 970
Quoted 6 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +5
-0+ compatible = "qcom,sm8450-lpass-ag-noc"; + reg = <0 0x3c40000 0 0x17200>; + #interconnect-cells = <1>; + qcom,bcm-voters = <&apps_bcm_voter>; + }; };
I don't see a DT node for clk_virt, are you planning to add this later?
Thanks,
Georgi
PATCH v2 10/13 arm64: dts: qcom: sm8450: add spmi node
In reply to Vinod KoulAdd the spmi bus as found in the SM8450 SoC
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +18 -0
@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + }; + tlmm: pinctrl@f100000 { compatible = "qcom,sm8450-tlmm"; reg = <0 0x0f100000 0 0x300000>;
Signature · 1 line
2.31.1
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0
arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;
This is a patch from December 2021. Is there anything blocking it from being merged?
The same applies to several other patches here.
Best regards,
Krzysztof
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 17 lines · Krzysztof Kozlowski
Quoted 16 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; };
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0+ spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
I think it depended on a series of changes to the driver, as 8450 has a newer SPMI ver
Konrad
Quoted 5 lines
The same applies to several other patches here.
Best regards,
Krzysztof
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 29 lines · On 24/10/2022 11:06, [email protected] wrote:
Quoted 18 lines · Krzysztof Kozlowski
Quoted 17 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; };Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 7 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0+ spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 3 lines
I think it depended on a series of changes to the driver, as 8450 has a newer SPMI ver
If the new device node in DTS (for new hardware) depends on driver changes, then something here is completely broken. Probably in the bindings for Qualcomm SPMI PMIC.
I expect adding DTS independently of driver changes. It anyway goes always via separate branches.
Best regards,
Krzysztof
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
In reply to Krzysztof KozlowskiQuoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 29 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 5 lines
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
Just like I replied to Konrad - if that's true, bindings are simply wrong and should be fixed.
Best regards,
Krzysztof
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 30 lines · Krzysztof Kozlowski
Quoted 29 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 8 lines
Quoted 5 lines
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
In this particular case, there was an open question, what should be the bindings for the PMIC ARB v7.
Quoted 3 lines
Just like I replied to Konrad - if that's true, bindings are simply wrong and should be fixed.
Maybe I missed the reply. Which email are you referring to?
Quoted 4 lines
Best regards,
Krzysztof
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 37 lines · Dmitry Baryshkov
Quoted 36 lines · Krzysztof Kozlowski
Quoted 34 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Quoted 5 lines
Quoted 2 lines
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
In this particular case, there was an open question, what should be the bindings for the PMIC ARB v7.
Ah, so it is about PMIC ARB v7 bindings? Then it's reasonable to wait with this one. I just had an impression that it's about driver changes...
Quoted 6 lines
Quoted 4 lines
Just like I replied to Konrad - if that's true, bindings are simply wrong and should be fixed.
Maybe I missed the reply. Which email are you referring to?
I meant about this one:
https://lore.kernel.org/linux-arm-msm/[email protected]/T/#m50f4c72775492046f9b0a172e974cab83563af3c
Best regards,
Krzysztof
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 39 lines · Krzysztof Kozlowski
Quoted 37 lines · Dmitry Baryshkov
Quoted 36 lines · Krzysztof Kozlowski
Quoted 34 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
In this particular case, there was an open question, what should be the bindings for the PMIC ARB v7.
Ah, so it is about PMIC ARB v7 bindings? Then it's reasonable to wait with this one. I just had an impression that it's about driver changes...
Yes, it's about binding. Thus we have been waiting for quite some time.
Quoted 11 lines
Quoted 7 lines
Quoted 5 lines
Just like I replied to Konrad - if that's true, bindings are simply wrong and should be fixed.
Maybe I missed the reply. Which email are you referring to?
I meant about this one:
https://lore.kernel.org/linux-arm-msm/[email protected]/T/#m50f4c72775492046f9b0a172e974cab83563af3c
Ack, for some reason I got it later than the previous one.
Quoted 4 lines
Best regards,
Krzysztof
Signature · 2 lines
With best wishes Dmitry
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 44 lines · Dmitry Baryshkov
Quoted 42 lines · Krzysztof Kozlowski
Quoted 40 lines · Dmitry Baryshkov
Quoted 38 lines · Krzysztof Kozlowski
Quoted 29 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 5 lines
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
In this particular case, there was an open question, what should be the bindings for the PMIC ARB v7.
Ah, so it is about PMIC ARB v7 bindings? Then it's reasonable to wait with this one. I just had an impression that it's about driver changes...
Yes, it's about binding. Thus we have been waiting for quite some time.
Yes sadly Steven has stopped responding to emails or IRC.. I am not sure whats going on!
Even the SPMI tree is not being actively maintained with only few patches which were picked in last cycle since this year!
Signature · 1 line
~Vinod
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 51 lines · Vinod Koul
Quoted 50 lines · Dmitry Baryshkov
Quoted 47 lines · Krzysztof Kozlowski
Quoted 37 lines · Dmitry Baryshkov
Quoted 36 lines · Krzysztof Kozlowski
Quoted 34 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Quoted 5 lines
Quoted 2 lines
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
In this particular case, there was an open question, what should be the bindings for the PMIC ARB v7.
Ah, so it is about PMIC ARB v7 bindings? Then it's reasonable to wait with this one. I just had an impression that it's about driver changes...
Quoted 7 lines
Quoted 1 line
Yes, it's about binding. Thus we have been waiting for quite some time.
Yes sadly Steven has stopped responding to emails or IRC.. I am not sure whats going on!
Even the SPMI tree is not being actively maintained with only few patches which were picked in last cycle since this year!
It's in -next now and 8450 boots and works fine. If the binding situation has been resolved, I say merge this ASAP! :)
Konrad
Quoted 1 line
Re: [PATCH v2 10/13] arm64: dts: qcom: sm8450: add spmi node
Quoted 56 lines · Konrad Dybcio
Quoted 53 lines · Vinod Koul
Quoted 51 lines · Dmitry Baryshkov
Quoted 39 lines · Krzysztof Kozlowski
Quoted 37 lines · Dmitry Baryshkov
Quoted 36 lines · Krzysztof Kozlowski
Quoted 34 lines · Dmitry Baryshkov
Quoted 28 lines · Krzysztof Kozlowski
Quoted 13 lines · Vinod Koul
Add the spmi bus as found in the SM8450 SoC
Signed-off-by Vinod Koul <[email protected]>Reviewed-by Konrad Dybcio <[email protected]>---
arch/arm64/boot/dts/qcom/sm8450.dtsi| 18 ++++++++++++++++++1 file changed, 18 insertions(+)arch/arm64/boot/dts/qcom/sm8450.dtsi +0
-0arch/arm64/boot/dts/qcom/sm8450.dtsi pdc: interrupt-controller@b220000 { · line 654
Quoted 10 lines
arch/arm64/boot/dts/qcom/sm8450.dtsi +7
-0@@ -645,6 +645,24 @@ pdc: interrupt-controller@b220000 { interrupt-controller; }; + spmi_bus: spmi@c42d000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0 0x0c400000 0x0 0x00003000>, + <0x0 0x0c500000 0x0 0x00400000>, + <0x0 0x0c440000 0x0 0x00080000>, + <0x0 0x0c4c0000 0x0 0x00010000>, + <0x0 0x0c42d000 0x0 0x00010000>;This is a patch from December 2021. Is there anything blocking it from being merged?
Quoted 1 line
The same applies to several other patches here.
As far as I know, Stephen still didn't pick up the spmi-pmic-arb support for the PMIC on the SM8450 platform. Thus we also can not merge the DT parts.
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
Why we cannot merge DTS? How is DTS with new nodes depending on any driver changes?
In this particular case, there was an open question, what should be the bindings for the PMIC ARB v7.
Ah, so it is about PMIC ARB v7 bindings? Then it's reasonable to wait with this one. I just had an impression that it's about driver changes...
Yes, it's about binding. Thus we have been waiting for quite some time.
Quoted 8 lines
Quoted 5 lines
Yes sadly Steven has stopped responding to emails or IRC.. I am not sure whats going on!
Even the SPMI tree is not being actively maintained with only few patches which were picked in last cycle since this year!
It's in -next now and 8450 boots and works fine. If the binding situation has been resolved, I say merge this ASAP! :)
Konrad
With a small nit: it needs to be rebased, and should come between aoss_qmp: and ipcc: address-wise (ipcc wasn't around a year ago in this DT, it seems). Also most (all?) other nodes in the DT use reg = <0 [..]> instead of reg = <0x0 [..]> so that could be fixed up as well.
Konrad
Quoted 1 line
Quoted 1 line
PATCH v2 11/13 arm64: dts: qcom: sm8450: Add rpmhpd node
In reply to Vinod KoulFrom: Dmitry Baryshkov <[email protected]>
This adds RPMH power domain found in SM8450 SoC
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +52 -0
@@ -8,6 +8,7 @@ #include <dt-bindings/clock/qcom,rpmh.h> #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interconnect/qcom,sm8450.h> +#include <dt-bindings/power/qcom-rpmpd.h> #include <dt-bindings/soc/qcom,rpmh-rsc.h> / {
@@ -888,6 +889,57 @@ rpmhcc: clock-controller { clock-names = "xo"; clocks = <&xo_board>; }; + + rpmhpd: power-controller { + compatible = "qcom,sm8450-rpmhpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmhpd_opp_table>; + + rpmhpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmhpd_opp_ret: opp1 { + opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; + }; + + rpmhpd_opp_min_svs: opp2 { + opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; + }; + + rpmhpd_opp_low_svs: opp3 { + opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; + }; + + rpmhpd_opp_svs: opp4 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS>; + }; + + rpmhpd_opp_svs_l1: opp5 { + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; + }; + + rpmhpd_opp_nom: opp6 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM>; + }; + + rpmhpd_opp_nom_l1: opp7 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; + }; + + rpmhpd_opp_nom_l2: opp8 { + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; + }; + + rpmhpd_opp_turbo: opp9 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; + }; + + rpmhpd_opp_turbo_l1: opp10 { + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; + }; + }; + }; + }; gem_noc: interconnect@19100000 {
Signature · 1 line
2.31.1
PATCH v2 12/13 arm64: dts: qcom: sm8450: add cpufreq support
In reply to Vinod KoulFrom: Vladimir Zapolskiy <[email protected]>
The change adds a description of a SM8450 cpufreq-epss controller and references to it from CPU nodes.
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +23 -0
@@ -45,6 +45,7 @@ CPU0: cpu@0 { next-level-cache = <&L2_0>; power-domains = <&CPU_PD0>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 0>; L2_0: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -62,6 +63,7 @@ CPU1: cpu@100 { next-level-cache = <&L2_100>; power-domains = <&CPU_PD1>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 0>; L2_100: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -76,6 +78,7 @@ CPU2: cpu@200 { next-level-cache = <&L2_200>; power-domains = <&CPU_PD2>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 0>; L2_200: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -90,6 +93,7 @@ CPU3: cpu@300 { next-level-cache = <&L2_300>; power-domains = <&CPU_PD3>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 0>; L2_300: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -104,6 +108,7 @@ CPU4: cpu@400 { next-level-cache = <&L2_400>; power-domains = <&CPU_PD4>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 1>; L2_400: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -118,6 +123,7 @@ CPU5: cpu@500 { next-level-cache = <&L2_500>; power-domains = <&CPU_PD5>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 1>; L2_500: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -133,6 +139,7 @@ CPU6: cpu@600 { next-level-cache = <&L2_600>; power-domains = <&CPU_PD6>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 1>; L2_600: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -147,6 +154,7 @@ CPU7: cpu@700 { next-level-cache = <&L2_700>; power-domains = <&CPU_PD7>; power-domain-names = "psci"; + qcom,freq-domain = <&cpufreq_hw 2>; L2_700: l2-cache { compatible = "cache"; next-level-cache = <&L3_0>;
@@ -942,6 +950,21 @@ rpmhpd_opp_turbo_l1: opp10 { }; + cpufreq_hw: cpufreq@17d91000 { + compatible = "qcom,sm8450-cpufreq-epss", "qcom,cpufreq-epss"; + reg = <0 0x17d91000 0 0x1000>, + <0 0x17d92000 0 0x1000>, + <0 0x17d93000 0 0x1000>; + reg-names = "freq-domain0", "freq-domain1", "freq-domain2"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>; + clock-names = "xo", "alternate"; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2"; + #freq-domain-cells = <1>; + }; + gem_noc: interconnect@19100000 { compatible = "qcom,sm8450-gem-noc"; reg = <0 0x19100000 0 0xbb800>;
Signature · 1 line
2.31.1
PATCH v2 13/13 arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes
In reply to Vinod KoulFrom: Dmitry Baryshkov <[email protected]>
Add device tree nodes for two i2c blocks: i2c13 and i2c14.
--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)
arch/arm64/boot/dts/qcom/sm8450.dtsi +52 -0
@@ -583,6 +583,44 @@ uart7: serial@99c000 { }; }; + qupv3_id_1: geniqup@ac0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x00ac0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>, + <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + i2c13: i2c@a94000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a94000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c13_data_clk>; + interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c14: i2c@a98000 { + compatible = "qcom,geni-i2c"; + reg = <0 0x00a98000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_i2c14_data_clk>; + interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + config_noc: interconnect@1500000 { compatible = "qcom,sm8450-config-noc"; reg = <0 0x01500000 0 0x1c000>;
@@ -683,6 +721,20 @@ tlmm: pinctrl@f100000 { gpio-ranges = <&tlmm 0 0 211>; wakeup-parent = <&pdc>; + qup_i2c13_data_clk: qup-i2c13-data-clk { + pins = "gpio48", "gpio49"; + function = "qup13"; + drive-strength = <2>; + bias-pull-up; + }; + + qup_i2c14_data_clk: qup-i2c14-data-clk { + pins = "gpio52", "gpio53"; + function = "qup14"; + drive-strength = <2>; + bias-pull-up; + }; + qup_uart7_rx: qup-uart7-rx { pins = "gpio26"; function = "qup7";
Signature · 1 line
2.31.1
Re: [PATCH v2 13/13] arm64: dts: qcom: sm8450: add i2c13 and i2c14 device nodes
Quoted 9 lines · Vinod Koul
From: Dmitry Baryshkov <[email protected]>
Add device tree nodes for two i2c blocks: i2c13 and i2c14.
Signed-off-by Dmitry Baryshkov <[email protected]>Signed-off-by Vinod Koul <[email protected]>--- arch/arm64/boot/dts/qcom/sm8450.dtsi | 52 ++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+)
Konrad