Skip to contentSkip to conversation

at803x fiber/SFP support

PATCH Superseded Robert Hancock 2 participants 5 messages Jan 12, 2022

Subsystems (3)

v3 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

v3 cover at803x fiber/SFP support

Add support for 1000Base-X fiber modes to the at803x PHY driver, as well as support for connecting a downstream SFP cage.

Changes since v2:
-fixed tabs/spaces issue in one patch

Changes since v1:
-moved page selection to config_init so it is handled properly after suspend/resume
-added explicit check for empty sfp_support bitmask

*** BLURB HERE ***

Robert Hancock (3):
net: phy: at803x: move page selection fix to config_init
net: phy: at803x: add fiber support
net: phy: at803x: Support downstream SFP cage

 drivers/net/phy/at803x.c | 146 +++++++++++++++++++++++++++++++++------
 1 file changed, 126 insertions(+), 20 deletions(-)
Signature · 1 line
2.31.1
#1 lore raw

PATCH v3 1/3 net: phy: at803x: move page selection fix to config_init

The fix to select the copper page on AR8031 was being done in the probe function rather than config_init, so it would not be redone after resume from suspend. Move this to config_init so it is always redone when needed.

Fixes c329e5afb42f ("net: phy: at803x: select correct page on config init")
---
 drivers/net/phy/at803x.c | 40 ++++++++++++++++------------------------
 1 file changed, 16 insertions(+), 24 deletions(-)
drivers/net/phy/at803x.c +16 -24
index dae95d9a07e8..3d7eeb572be8 100644
@@ -784,25 +784,7 @@ static int at803x_probe(struct phy_device *phydev)
 			return ret;
 	}
 
-	/* Some bootloaders leave the fiber page selected.
-	 * Switch to the copper page, as otherwise we read
-	 * the PHY capabilities from the fiber side.
-	 */
-	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-		phy_lock_mdio_bus(phydev);
-		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
-		phy_unlock_mdio_bus(phydev);
-		if (ret)
-			goto err;
-	}
-
 	return 0;
-
-err:
-	if (priv->vddio)
-		regulator_disable(priv->vddio);
-
-	return ret;
 }
 
 static void at803x_remove(struct phy_device *phydev)
@@ -912,6 +894,22 @@ static int at803x_config_init(struct phy_device *phydev)
 {
 	int ret;
 
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+		/* Some bootloaders leave the fiber page selected.
+		 * Switch to the copper page, as otherwise we read
+		 * the PHY capabilities from the fiber side.
+		 */
+		phy_lock_mdio_bus(phydev);
+		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
+		phy_unlock_mdio_bus(phydev);
+		if (ret)
+			return ret;
+
+		ret = at8031_pll_config(phydev);
+		if (ret < 0)
+			return ret;
+	}
+
 	/* The RX and TX delay default is:
 	 *   after HW reset: RX delay enabled and TX delay disabled
 	 *   after SW reset: RX delay enabled, while TX delay retains the
@@ -941,12 +939,6 @@ static int at803x_config_init(struct phy_device *phydev)
 	if (ret < 0)
 		return ret;
 
-	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
-		ret = at8031_pll_config(phydev);
-		if (ret < 0)
-			return ret;
-	}
-
 	/* Ar803x extended next page bit is enabled by default. Cisco
 	 * multigig switches read this bit and attempt to negotiate 10Gbps
 	 * rates even if the next page bit is disabled. This is incorrect
Signature · 1 line
2.31.1
#2 lore raw

PATCH v3 2/3 net: phy: at803x: add fiber support

In reply to Robert Hancock

Previously this driver always forced the copper page to be selected, however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page needs to be selected. Set the appropriate mode based on the hardware mode_cfg strap selection.

Enable the appropriate interrupt bits to detect fiber-side link up or down events.

Update config_aneg and read_status methods to use the appropriate Clause 37 calls when fiber mode is in use.

---
 drivers/net/phy/at803x.c | 76 +++++++++++++++++++++++++++++++++++-----
 1 file changed, 67 insertions(+), 9 deletions(-)
drivers/net/phy/at803x.c +67 -9
index 3d7eeb572be8..63d84eb2eddb 100644
@@ -51,6 +51,8 @@
 #define AT803X_INTR_ENABLE_PAGE_RECEIVED	BIT(12)
 #define AT803X_INTR_ENABLE_LINK_FAIL		BIT(11)
 #define AT803X_INTR_ENABLE_LINK_SUCCESS		BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX		BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX	BIT(7)
 #define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE	BIT(5)
 #define AT803X_INTR_ENABLE_POLARITY_CHANGED	BIT(1)
 #define AT803X_INTR_ENABLE_WOL			BIT(0)
@@ -85,7 +87,17 @@
 #define AT803X_DEBUG_DATA			0x1E
 
 #define AT803X_MODE_CFG_MASK			0x0F
-#define AT803X_MODE_CFG_SGMII			0x01
+#define AT803X_MODE_CFG_BASET_RGMII		0x00
+#define AT803X_MODE_CFG_BASET_SGMII		0x01
+#define AT803X_MODE_CFG_BX1000_RGMII_50		0x02
+#define AT803X_MODE_CFG_BX1000_RGMII_75		0x03
+#define AT803X_MODE_CFG_BX1000_CONV_50		0x04
+#define AT803X_MODE_CFG_BX1000_CONV_75		0x05
+#define AT803X_MODE_CFG_FX100_RGMII_50		0x06
+#define AT803X_MODE_CFG_FX100_CONV_50		0x07
+#define AT803X_MODE_CFG_RGMII_AUTO_MDET		0x0B
+#define AT803X_MODE_CFG_FX100_RGMII_75		0x0E
+#define AT803X_MODE_CFG_FX100_CONV_75		0x0F
 
 #define AT803X_PSSR				0x11	/*PHY-Specific Status Register*/
 #define AT803X_PSSR_MR_AN_COMPLETE		0x0200
@@ -283,6 +295,8 @@ struct at803x_priv {
 	u16 clk_25m_mask;
 	u8 smarteee_lpi_tw_1g;
 	u8 smarteee_lpi_tw_100m;
+	bool is_fiber;
+	bool is_1000basex;
 	struct regulator_dev *vddio_rdev;
 	struct regulator_dev *vddh_rdev;
 	struct regulator *vddio;
@@ -784,7 +798,33 @@ static int at803x_probe(struct phy_device *phydev)
 			return ret;
 	}
 
+	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+		int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+		int mode_cfg;
+
+		if (ccr < 0)
+			goto err;
+		mode_cfg = ccr & AT803X_MODE_CFG_MASK;
+
+		switch (mode_cfg) {
+		case AT803X_MODE_CFG_BX1000_RGMII_50:
+		case AT803X_MODE_CFG_BX1000_RGMII_75:
+			priv->is_1000basex = true;
+			fallthrough;
+		case AT803X_MODE_CFG_FX100_RGMII_50:
+		case AT803X_MODE_CFG_FX100_RGMII_75:
+			priv->is_fiber = true;
+			break;
+		}
+	}
+
 	return 0;
+
+err:
+	if (priv->vddio)
+		regulator_disable(priv->vddio);
+
+	return ret;
 }
 
 static void at803x_remove(struct phy_device *phydev)
@@ -797,6 +837,7 @@ static void at803x_remove(struct phy_device *phydev)
 
 static int at803x_get_features(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int err;
 
 	err = genphy_read_abilities(phydev);
@@ -823,12 +864,13 @@ static int at803x_get_features(struct phy_device *phydev)
 	 * As a result of that, ESTATUS_1000_XFULL is set
 	 * to 1 even when operating in copper TP mode.
 	 *
-	 * Remove this mode from the supported link modes,
-	 * as this driver currently only supports copper
-	 * operation.
+	 * Remove this mode from the supported link modes
+	 * when not operating in 1000BaseX mode.
 	 */
-	linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
-			   phydev->supported);
+	if (!priv->is_1000basex)
+		linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+				   phydev->supported);
+
 	return 0;
 }
 
@@ -892,15 +934,18 @@ static int at8031_pll_config(struct phy_device *phydev)
 
 static int at803x_config_init(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int ret;
 
 	if (phydev->drv->phy_id == ATH8031_PHY_ID) {
 		/* Some bootloaders leave the fiber page selected.
-		 * Switch to the copper page, as otherwise we read
-		 * the PHY capabilities from the fiber side.
+		 * Switch to the appropriate page (fiber or copper), as otherwise we
+		 * read the PHY capabilities from the wrong page.
 		 */
 		phy_lock_mdio_bus(phydev);
-		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
+		ret = at803x_write_page(phydev,
+					priv->is_fiber ? AT803X_PAGE_FIBER :
+							 AT803X_PAGE_COPPER);
 		phy_unlock_mdio_bus(phydev);
 		if (ret)
 			return ret;
@@ -959,6 +1004,7 @@ static int at803x_ack_interrupt(struct phy_device *phydev)
 
 static int at803x_config_intr(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int err;
 	int value;
 
@@ -975,6 +1021,10 @@ static int at803x_config_intr(struct phy_device *phydev)
 		value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
 		value |= AT803X_INTR_ENABLE_LINK_FAIL;
 		value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+		if (priv->is_fiber) {
+			value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
+			value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
+		}
 
 		err = phy_write(phydev, AT803X_INTR_ENABLE, value);
 	} else {
@@ -1107,8 +1157,12 @@ static int at803x_read_specific_status(struct phy_device *phydev)
 
 static int at803x_read_status(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int err, old_link = phydev->link;
 
+	if (priv->is_1000basex)
+		return genphy_c37_read_status(phydev);
+
 	/* Update the link, but return if there was an error */
 	err = genphy_update_link(phydev);
 	if (err)
@@ -1162,6 +1216,7 @@ static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
 
 static int at803x_config_aneg(struct phy_device *phydev)
 {
+	struct at803x_priv *priv = phydev->priv;
 	int ret;
 
 	ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
@@ -1178,6 +1233,9 @@ static int at803x_config_aneg(struct phy_device *phydev)
 			return ret;
 	}
 
+	if (priv->is_1000basex)
+		return genphy_c37_config_aneg(phydev);
+
 	/* Do not restart auto-negotiation by setting ret to 0 defautly,
 	 * when calling __genphy_config_aneg later.
 	 */
Signature · 1 line
2.31.1
#3 lore raw

PATCH v3 3/3 net: phy: at803x: Support downstream SFP cage

In reply to Robert Hancock

Add support for downstream SFP cages for AR8031 and AR8033. This is primarily intended for fiber modules or direct-attach cables, however copper modules which work in 1000Base-X mode may also function. Such modules are allowed with a warning.

---
 drivers/net/phy/at803x.c | 56 ++++++++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)
drivers/net/phy/at803x.c +56 -0
index 63d84eb2eddb..c4e87c76edcb 100644
@@ -19,6 +19,8 @@
 #include <linux/regulator/of_regulator.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/consumer.h>
+#include <linux/phylink.h>
+#include <linux/sfp.h>
 #include <dt-bindings/net/qca-ar803x.h>
 
 #define AT803X_SPECIFIC_FUNCTION_CONTROL	0x10
@@ -664,6 +666,55 @@ static int at8031_register_regulators(struct phy_device *phydev)
 	return 0;
 }
 
+static int at803x_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
+{
+	struct phy_device *phydev = upstream;
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support);
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support);
+	phy_interface_t iface;
+
+	linkmode_zero(phy_support);
+	phylink_set(phy_support, 1000baseX_Full);
+	phylink_set(phy_support, 1000baseT_Full);
+	phylink_set(phy_support, Autoneg);
+	phylink_set(phy_support, Pause);
+	phylink_set(phy_support, Asym_Pause);
+
+	linkmode_zero(sfp_support);
+	sfp_parse_support(phydev->sfp_bus, id, sfp_support);
+	/* Some modules support 10G modes as well as others we support.
+	 * Mask out non-supported modes so the correct interface is picked.
+	 */
+	linkmode_and(sfp_support, phy_support, sfp_support);
+
+	if (linkmode_empty(sfp_support)) {
+		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
+		return -EINVAL;
+	}
+
+	iface = sfp_select_interface(phydev->sfp_bus, sfp_support);
+
+	/* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes
+	 * interface for use with SFP modules.
+	 * However, some copper modules detected as having a preferred SGMII
+	 * interface do default to and function in 1000Base-X mode, so just
+	 * print a warning and allow such modules, as they may have some chance
+	 * of working.
+	 */
+	if (iface == PHY_INTERFACE_MODE_SGMII)
+		dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n");
+	else if (iface != PHY_INTERFACE_MODE_1000BASEX)
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct sfp_upstream_ops at803x_sfp_ops = {
+	.attach = phy_sfp_attach,
+	.detach = phy_sfp_detach,
+	.module_insert = at803x_sfp_insert,
+};
+
 static int at803x_parse_dt(struct phy_device *phydev)
 {
 	struct device_node *node = phydev->mdio.dev.of_node;
@@ -771,6 +822,11 @@ static int at803x_parse_dt(struct phy_device *phydev)
 			phydev_err(phydev, "failed to get VDDIO regulator\n");
 			return PTR_ERR(priv->vddio);
 		}
+
+		/* Only AR8031/8033 support 1000Base-X for SFP modules */
+		ret = phy_sfp_probe(phydev, &at803x_sfp_ops);
+		if (ret < 0)
+			return ret;
 	}
 
 	return 0;
Signature · 1 line
2.31.1
maintainer
#4 lore raw
In reply to Robert Hancock
Quoted 10 lines · On Wed, 12 Jan 2022 11:44:15 -0600 Robert Hancock wrote:

Add support for 1000Base-X fiber modes to the at803x PHY driver, as well as support for connecting a downstream SFP cage.

Changes since v2:
-fixed tabs/spaces issue in one patch

Changes since v1:
-moved page selection to config_init so it is handled properly after suspend/resume
-added explicit check for empty sfp_support bitmask

Please not that net-next is closed during the merge window, all the non-fixes will have to be reposted. Looks like patch 1 can be separated out of this series and reposted for net.

# Form letter - net-next is closed

We have already sent the networking pull request for 5.17 and therefore net-next is closed for new drivers, features, code refactoring and optimizations. We are currently accepting bug fixes only.

Please repost when net-next reopens after 5.17-rc1 is cut.

Look out for the announcement on the mailing list or check:
http://vger.kernel.org/~davem/net-next.html

RFC patches sent for review only are obviously welcome at any time.