Add support for the Purism Librem5 Phone
Subsystems (3)
cover Add support for the Purism Librem5 Phone
I sent this patchset as a single monolithic patch and did not see any comment on it.
https://lists.denx.de/pipermail/u-boot/2022-January/471087.html
Here it is as a set of patches instead.
This is all of the code required to boot the Librem5 Phone.
It can boot the phone in uuu mode or directly from the eMMC
Angus Ainslie (13):
MAINTAINERS: add Purism to the maintainers file
arm: dts: add the Purism devicetree files
arm: imx8m: add Purism Librem5 Kconfig
configs: add the Librem5 defconfig
include: configs: add the librem5.h include file
board: librem5: add the u-boot source for the Librem5
board: librem5: add the u-boot header for the Librem5
board: librem5: add the SPL source for the Librem5
board: librem5: add the LPDDR4 source for the Librem5
board: librem5: add SPL loader configuration
board: librem5: add Librem5 MAINTAINERS file
board: librem5: add Librem5 build files
doc: librem5: add Librem5 documentation
MAINTAINERS | 9 + arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mq-librem5-u-boot.dtsi | 134 ++ arch/arm/dts/imx8mq-librem5.dts | 593 ++++++++ arch/arm/mach-imx/imx8m/Kconfig | 9 + board/purism/librem5/Kconfig | 15 + board/purism/librem5/MAINTAINERS | 7 + board/purism/librem5/Makefile | 13 + board/purism/librem5/imximage-8mq-lpddr4.cfg | 9 + board/purism/librem5/librem5.c | 708 ++++++++++ board/purism/librem5/librem5.h | 176 +++ board/purism/librem5/lpddr4_timing.c | 1324 ++++++++++++++++++ board/purism/librem5/lpddr4_timing_b0.c | 1191 ++++++++++++++++ board/purism/librem5/spl.c | 481 +++++++ configs/librem5_defconfig | 120 ++ doc/board/purism/librem5/librem5.rst | 60 + include/configs/librem5.h | 171 +++ 17 files changed, 5022 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx8mq-librem5-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mq-librem5.dts create mode 100644 board/purism/librem5/Kconfig create mode 100644 board/purism/librem5/MAINTAINERS create mode 100644 board/purism/librem5/Makefile create mode 100644 board/purism/librem5/imximage-8mq-lpddr4.cfg create mode 100644 board/purism/librem5/librem5.c create mode 100644 board/purism/librem5/librem5.h create mode 100644 board/purism/librem5/lpddr4_timing.c create mode 100644 board/purism/librem5/lpddr4_timing_b0.c create mode 100644 board/purism/librem5/spl.c create mode 100644 configs/librem5_defconfig create mode 100644 doc/board/purism/librem5/librem5.rst create mode 100644 include/configs/librem5.h
Signature · 1 line
2.25.1
PATCH 1/13 MAINTAINERS: add Purism to the maintainers file
The Purism kernel team is in charge of maintianing the Librem5 u-boot
--- MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+)
MAINTAINERS +9 -0
@@ -1079,6 +1079,15 @@ S: Maintained T: git https://source.denx.de/u-boot/custodians/u-boot-mpc85xx.git F: arch/powerpc/cpu/mpc85xx/ +PURISM LIBREM5 PHONE +M: Angus Ainslie <[email protected]> +R: [email protected] +S: Supported +F: arch/arm/dts/imx8mq-* +F: board/purism/librem5/ +F: configs/librem5_defconfig +F: include/configs/librem5.h + RISC-V M: Rick Chen <[email protected]> M: Leo <[email protected]>
Signature · 1 line
2.25.1
Re: [PATCH 01/13] MAINTAINERS: add Purism to the maintainers file
Quoted 6 lines · Angus Ainslie
The Purism kernel team is in charge of maintianing the Librem5 u-boot
Signed-off-by Angus Ainslie <[email protected]>--- MAINTAINERS | 9 +++++++++ 1 file changed, 9 insertions(+)
In U-Boot this is done all within board/.../MAINTAINERS instead of the top-level file, thanks!
Signature · 1 line
Tom
PATCH 2/13 arm: dts: add the Purism devicetree files
In reply to Angus AinslieInitial commit of Librem5 devicetree files
--- arch/arm/dts/Makefile | 3 +- arch/arm/dts/imx8mq-librem5-u-boot.dtsi | 134 ++++++ arch/arm/dts/imx8mq-librem5.dts | 593 ++++++++++++++++++++++++ 3 files changed, 729 insertions(+), 1 deletion(-) create mode 100644 arch/arm/dts/imx8mq-librem5-u-boot.dtsi create mode 100644 arch/arm/dts/imx8mq-librem5.dts
arch/arm/dts/Makefile +2 -1
@@ -912,7 +912,8 @@ dtb-$(CONFIG_ARCH_IMX8M) += \ imx8mq-phanbell.dtb \ imx8mp-evk.dtb \ imx8mp-phyboard-pollux-rdk.dtb \ - imx8mq-pico-pi.dtb + imx8mq-pico-pi.dtb \ + imx8mq-librem5.dtb dtb-$(CONFIG_ARCH_IMXRT) += imxrt1050-evk.dtb \ imxrt1020-evk.dtb
arch/arm/dts/imx8mq-librem5-u-boot.dtsi new file +134 -0
134 lines not on this page · raw message
arch/arm/dts/imx8mq-librem5.dts new file +593 -0
593 lines not on this page · raw message
Signature · 1 line
2.25.1
Re: [PATCH 02/13] arm: dts: add the Purism devicetree files
Quoted 3 lines · Angus Ainslie
Initial commit of Librem5 devicetree files
Signed-off-by Angus Ainslie <[email protected]>
Please note what kernel release the not -u-boot.dtsi files are a copy from, as they need to be copies and not modified, thanks.
Signature · 1 line
Tom
Re: [PATCH 02/13] arm: dts: add the Purism devicetree files
Hi Tom,
Quoted 8 lines · Tom Rini
Quoted 3 lines · Angus Ainslie
Initial commit of Librem5 devicetree files
Signed-off-by Angus Ainslie <[email protected]>Please note what kernel release the not
-u-boot.dtsifiles are a copy from, as they need to be copies and not modified, thanks.
There's an issue with adding the devicetree from the 5.16 kernel.
I get a compilation error due to a :missing .h in the devicetree files:
In file included from arch/arm/dts/imx8mq-librem5-r3.dtsi:11,
from arch/arm/dts/.imx8mq-librem5.dtb.pre.tmp:6:
arch/arm/dts/imx8mq-librem5.dtsi:13:10: fatal error: dt-bindings/rfkill/rfkill.h: No such file or directory
13 | #include "dt-bindings/rfkill/rfkill.h"
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~Should that get added to the u-boot source as well or should I modify the dts to remove this ?
For the kernel we also have 4 different dts files for the differences in PCB versions. For u-boot we don't need the differentiation as it deals with things like camera rotation and prox sensor sensitivity.
There's 2 ways to solve the this I think.
1) just use the latest librem5 dts file which is made up of 3 different dts(i) files.
2) have a defconfig for each of the different PCB versions.
Do you have a preference ?
Thanks
Angus
Re: [PATCH 02/13] arm: dts: add the Purism devicetree files
Quoted 17 lines · Angus Ainslie
Hi Tom,
Quoted 8 lines · Tom Rini
Quoted 3 lines · Angus Ainslie
Initial commit of Librem5 devicetree files
Signed-off-by Angus Ainslie <[email protected]>Please note what kernel release the not
-u-boot.dtsifiles are a copy from, as they need to be copies and not modified, thanks.There's an issue with adding the devicetree from the 5.16 kernel.
I get a compilation error due to a :missing .h in the devicetree files:
In file included from
arch/arm/dts/imx8mq-librem5-r3.dtsi:11,
Quoted 8 lines
from arch/arm/dts/.imx8mq-librem5.dtb.pre.tmp:6: arch/arm/dts/imx8mq-librem5.dtsi:13:10: fatal error: dt-bindings/rfkill/rfkill.h: No such file or directory 13 | #include "dt-bindings/rfkill/rfkill.h" | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~Should that get added to the u-boot source as well or should I modify the dts to remove this ?
Import the missing binding(s) in a separate commit first please.
Quoted 11 lines
For the kernel we also have 4 different dts files for the differences in PCB versions. For u-boot we don't need the differentiation as it deals with things like camera rotation and prox sensor sensitivity.
There's 2 ways to solve the this I think.
1) just use the latest librem5 dts file which is made up of 3 different dts(i) files.
2) have a defconfig for each of the different PCB versions.Do you have a preference ?
Can you tell the revision at run-time? We have examples of boards that can and will include revA.dtb and revB.dtb and select the correct one at run time (and start with something that works on revA and revB).
Signature · 1 line
Tom
Re: [PATCH 02/13] arm: dts: add the Purism devicetree files
Quoted 8 lines · Tom Rini
Quoted 7 lines · Angus Ainslie
There's 2 ways to solve the this I think.
1) just use the latest librem5 dts file which is made up of 3 different dts(i) files.
2) have a defconfig for each of the different PCB versions.
Quoted 5 lines
Quoted 1 line
Do you have a preference ?
Can you tell the revision at run-time? We have examples of boards that can and will include revA.dtb and revB.dtb and select the correct one at run time (and start with something that works on revA and revB).
Due to some changes by NXP in the fuse section of the imx8mq we can't reliably detect some of the earlier revisions.
Going forward we should be able to using this
https://lists.denx.de/pipermail/u-boot/2021-November/468419.html
But that will be post r4 boards.
Re: [PATCH 02/13] arm: dts: add the Purism devicetree files
Quoted 16 lines · Angus Ainslie
Quoted 9 lines · Tom Rini
Quoted 8 lines · Angus Ainslie
There's 2 ways to solve the this I think.
1) just use the latest librem5 dts file which is made up of 3 different
dts(i) files.
2) have a defconfig for each of the different PCB versions.Quoted 5 lines
Quoted 1 line
Do you have a preference ?
Can you tell the revision at run-time? We have examples of boards that can and will include revA.dtb and revB.dtb and select the correct one at run time (and start with something that works on revA and revB).
Quoted 8 lines
Due to some changes by NXP in the fuse section of the imx8mq we can't reliably detect some of the earlier revisions.
Going forward we should be able to using this
https://lists.denx.de/pipermail/u-boot/2021-November/468419.html
But that will be post r4 boards.
Ah "fun". I guess I'd lean towards #1 then if you think that'll be easy enough on the end users too.
Signature · 1 line
Tom
PATCH 3/13 arm: imx8m: add Purism Librem5 Kconfig
In reply to Angus AinslieAdd the Librem5 target
--- arch/arm/mach-imx/imx8m/Kconfig | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm/mach-imx/imx8m/Kconfig +9 -0
@@ -160,6 +160,14 @@ config TARGET_IMX8MM_CL_IOT_GATE_OPTEE select IMX8MM select SUPPORT_SPL select IMX8M_LPDDR4 + +config TARGET_LIBREM5 + bool "Purism Librem5 Phone" + select BINMAN + select IMX8MQ + select SUPPORT_SPL + select IMX8M_LPDDR4 + endchoice source "board/beacon/imx8mm/Kconfig"
@@ -175,6 +183,7 @@ source "board/google/imx8mq_phanbell/Kconfig" source "board/kontron/sl-mx8mm/Kconfig" source "board/phytec/phycore_imx8mm/Kconfig" source "board/phytec/phycore_imx8mp/Kconfig" +source "board/purism/librem5/Kconfig" source "board/ronetix/imx8mq-cm/Kconfig" source "board/technexion/pico-imx8mq/Kconfig" source "board/toradex/verdin-imx8mm/Kconfig"
Signature · 1 line
2.25.1
PATCH 4/13 configs: add the Librem5 defconfig
In reply to Angus AinslieInitial commit of the Librem5 defconfig
--- configs/librem5_defconfig | 120 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 120 insertions(+) create mode 100644 configs/librem5_defconfig
configs/librem5_defconfig new file +120 -0
@@ -0,0 +1,120 @@ +CONFIG_ARM=y +CONFIG_ARCH_IMX8M=y +CONFIG_SYS_TEXT_BASE=0x40200000 +CONFIG_SPL_GPIO=y +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_ENV_SIZE=0x2000 +CONFIG_ENV_OFFSET=0x3FE000 +CONFIG_SYS_I2C_MXC_I2C1=y +CONFIG_SYS_I2C_MXC_I2C2=y +CONFIG_SYS_I2C_MXC_I2C3=y +CONFIG_SYS_I2C_MXC_I2C4=y +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="imx8mq-librem5" +CONFIG_SPL_TEXT_BASE=0x7E1000 +CONFIG_TARGET_LIBREM5=y +CONFIG_SPL_MMC=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_DRIVERS_MISC=y +CONFIG_SPL=y +CONFIG_IMX_BOOTAUX=y +CONFIG_DISTRO_DEFAULTS=y +CONFIG_SYS_LOAD_ADDR=0x40480000 +CONFIG_FIT=y +CONFIG_FIT_EXTERNAL_OFFSET=0x3000 +CONFIG_SPL_LOAD_FIT=y +# CONFIG_USE_SPL_FIT_GENERATOR is not set +CONFIG_OF_SYSTEM_SETUP=y +CONFIG_ARCH_MISC_INIT=y +CONFIG_BOARD_EARLY_INIT_F=y +CONFIG_BOARD_LATE_INIT=y +CONFIG_SPL_BOARD_INIT=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_I2C=y +CONFIG_SPL_POWER=y +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_USB_SDP_SUPPORT=y +CONFIG_SPL_WATCHDOG=y +CONFIG_CMD_MEMTEST=y +CONFIG_CMD_FUSE=y +CONFIG_CMD_GPIO=y +CONFIG_CMD_I2C=y +CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_SDP=y +CONFIG_CMD_CACHE=y +CONFIG_CMD_REGULATOR=y +CONFIG_CMD_EXT4_WRITE=y +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_ENV_IS_IN_MMC=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_WARN=y +# CONFIG_SPL_BLK is not set +CONFIG_SAVED_DRAM_TIMING_BASE=0x40000000 +CONFIG_USB_FUNCTION_FASTBOOT=y +CONFIG_FASTBOOT_BUF_ADDR=0x43000000 +CONFIG_FASTBOOT_BUF_SIZE=0x40000000 +CONFIG_FASTBOOT_FLASH=y +CONFIG_FASTBOOT_UUU_SUPPORT=y +CONFIG_FASTBOOT_FLASH_MMC_DEV=0 +CONFIG_FASTBOOT_MMC_BOOT_SUPPORT=y +CONFIG_FASTBOOT_MMC_USER_SUPPORT=y +CONFIG_FASTBOOT_CMD_OEM_PARTCONF=y +CONFIG_FASTBOOT_CMD_OEM_BOOTBUS=y +# CONFIG_SPL_DM_GPIO is not set +CONFIG_GPIO_HOG=y +CONFIG_DM_GPIO_LOOKUP_LABEL=y +CONFIG_MXC_GPIO=y +CONFIG_DM_I2C=y +# CONFIG_SPL_DM_I2C is not set +CONFIG_SPL_SYS_I2C_LEGACY=y +CONFIG_SYS_I2C_EARLY_INIT=y +CONFIG_SYS_MXC_I2C1_SPEED=50000 +CONFIG_SYS_MXC_I2C2_SPEED=50000 +CONFIG_SYS_MXC_I2C3_SPEED=50000 +CONFIG_SYS_MXC_I2C4_SPEED=50000 +CONFIG_SYS_I2C_SPEED=50000 +CONFIG_LED=y +CONFIG_LED_BLINK=y +CONFIG_LED_GPIO=y +CONFIG_MISC=y +# CONFIG_SPL_DM_MMC is not set +CONFIG_SUPPORT_EMMC_BOOT=y +CONFIG_MMC_IO_VOLTAGE=y +CONFIG_FSL_USDHC=y +CONFIG_DM_SPI_FLASH=y +CONFIG_SPI_FLASH_STMICRO=y +CONFIG_SPI_FLASH_WINBOND=y +CONFIG_DM_ETH=y +CONFIG_PHY=y +CONFIG_PHY_IMX8MQ_USB=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_IMX8M=y +CONFIG_POWER_LEGACY=y +CONFIG_POWER_DOMAIN=y +CONFIG_IMX8M_POWER_DOMAIN=y +CONFIG_DM_REGULATOR=y +CONFIG_DM_REGULATOR_FIXED=y +CONFIG_DM_REGULATOR_GPIO=y +CONFIG_POWER_I2C=y +CONFIG_DM_RESET=y +CONFIG_MXC_UART=y +CONFIG_SPI=y +CONFIG_DM_SPI=y +CONFIG_MXC_SPI=y +CONFIG_DM_THERMAL=y +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Purism" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_SDP_LOADADDR=0x40400000
Signature · 1 line
2.25.1
PATCH 5/13 include: configs: add the librem5.h include file
In reply to Angus AinslieInitial commit of the librem5.h configuration
--- include/configs/librem5.h | 171 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 171 insertions(+) create mode 100644 include/configs/librem5.h
include/configs/librem5.h new file +171 -0
@@ -0,0 +1,171 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright 2017 NXP +* Copyright 2018 Emcraft Systems +* Copyright 2019 Purism +* +*/ + +#ifndef __LIBREM5_H +#define __LIBREM5_H + +/* #define DEBUG */ + +#include <version.h> +#include <linux/sizes.h> +#include <asm/arch/imx-regs.h> + +#ifdef CONFIG_SECURE_BOOT +#define CONFIG_CSF_SIZE 0x2000/* 8K region */ +#endif + +#define CONFIG_SPL_MAX_SIZE (148 * 1024) +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 +#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_THERM_SUPPORT +#define CONFIG_SPL_WATCHDOG_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_STACK 0x187FF0 +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_BSS_START_ADDR 0x00180000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x2000/* 8 KB */ +#define CONFIG_SPL_STACK_R_ADDR 0x42300000 +#define CONFIG_SPL_STACK_R +#define CONFIG_SYS_SPL_MALLOC_START 0x42200000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000/* 512 KB */ +#define CONFIG_SYS_ICACHE_OFF +#define CONFIG_SYS_DCACHE_OFF + +#define CONFIG_MALLOC_F_ADDR 0x182000/* malloc f used before GD_FLG_FULL_MALLOC_INIT */ + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */ + +#undef CONFIG_SPL_DM_PMIC +#undef CONFIG_SPL_DM_I2C +#undef CONFIG_SPL_DM_PMIC_BD71837 +#undef CONFIG_DM_USB +#undef CONFIG_SPL_DM_USB +#undef CONFIG_USB_DWC3_GENERIC +#undef CONFIG_DEVRES + +#define CONFIG_SYS_I2C + +#define CONFIG_POWER_BD71837 +#define CONFIG_POWER_BD71837_I2C_BUS 0 +#define CONFIG_POWER_BD71837_I2C_ADDR 0x4B + +#define CONFIG_SPL_DMA_SUPPORT + +#define CONFIG_SYS_FSL_USDHC_NUM 1 + +#else /* CONFIG_SPL_BUILD*/ + +#define CONFIG_SYS_FSL_USDHC_NUM 2 + +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 + +#define CONFIG_USBD_HS + +#define CONFIG_USB_GADGET_VBUS_DRAW 2 + +#endif /* CONFIG_SPL_BUILD*/ + +#define CONSOLE_ON_UART1 +#define CONFIG_BAUDRATE 115200 + +#ifdef CONSOLE_ON_UART1 +#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR +#define CONSOLE_UART_CLK 0 +#define CONSOLE "ttymxc0" +#elif defined(CONSOLE_ON_UART2 ) +#define CONFIG_MXC_UART_BASE UART2_BASE_ADDR +#define CONSOLE_UART_CLK 1 +#define CONSOLE "ttymxc1" +#elif defined(CONSOLE_ON_UART3 ) +#define CONFIG_MXC_UART_BASE UART3_BASE_ADDR +#define CONSOLE_UART_CLK 2 +#define CONSOLE "ttymxc2" +#elif defined(CONSOLE_ON_UART4 ) +#define CONFIG_MXC_UART_BASE UART4_BASE_ADDR +#define CONSOLE_UART_CLK 3 +#define CONSOLE "ttymxc3" +#else +#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR +#define CONSOLE_UART_CLK 0 +#define CONSOLE "ttymxc0" +#endif + +#define CONFIG_REMAKE_ELF + +#define CONFIG_BOARD_POSTCLK_INIT + +/* Flat Device Tree Definitions */ +#define CONFIG_OF_BOARD_SETUP + +#ifndef CONFIG_SPL_BUILD +#define BOOT_TARGET_DEVICES (func) \ + func(MMC, mmc, 0) \ + func(MMC, mmc, 1) \ + func(USB, usb, 0) \ + func(PXE, pxe, na) \ + func(DHCP, dhcp, na) +#include <config_distro_bootcmd.h> +#else +#define BOOTENV +#endif + +/* Initial environment variables */ +#define CONFIG_EXTRA_ENV_SETTINGS \ + "scriptaddr=0x80000000\0" \ + "pxefile_addr_r=0x80100000\0" \ + "kernel_addr_r=0x80800000\0" \ + "fdt_addr_r=0x83000000\0" \ + "ramdisk_addr_r=0x83800000\0" \ + "console=" CONSOLE ",115200\0" \ + "bootargs=u_boot_version=" PLAIN_VERSION "\0" \ + "stdin=nc,serial\0" \ + "stdout=nc,serial\0" \ + "stderr=nc,serial\0" \ + BOOTENV + +/* Link Definitions */ +#define CONFIG_SYS_TEXT_BASE 0x40200000 + +#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 +#define CONFIG_SYS_INIT_RAM_SIZE 0x80000 +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +#define CONFIG_ENV_OVERWRITE +#define CONFIG_MMCROOT "/dev/mmcblk0p2"/* USDHC1 */ + +#define CONFIG_SYS_SDRAM_BASE 0x40000000 +#define PHYS_SDRAM 0x40000000 +#define PHYS_SDRAM_SIZE 0xc0000000/* 3GB LPDDR4 one Rank */ + +#define CONFIG_SYS_ALT_MEMTEST + +/* Monitor Command Prompt */ +#undef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "u-boot=> " +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " +#define CONFIG_SYS_CBSIZE 1024 +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 + +#ifdef CONFIG_CMD_SF +#define CONFIG_SF_DEFAULT_BUS 0 +#define CONFIG_SF_DEFAULT_CS 0 +#endif +#endif
Signature · 1 line
2.25.1
Re: [PATCH 05/13] include: configs: add the librem5.h include file
Quoted 3 lines · Angus Ainslie
Initial commit of the
librem5.hconfigurationSigned-off-by Angus Ainslie <[email protected]>
You'll want to use CI
(https://u-boot.readthedocs.io/en/latest/develop/ci_testing.html) to get this tested for migrated symbols, or copy the CI logic out to a script and do that manually as I suspect there's some symbols here that need to be in the defconfig. Also:
Quoted 40 lines
include/configs/librem5.h new file +40
-0+#ifdef CONFIG_SPL_BUILD +#define CONFIG_SPL_THERM_SUPPORT +#define CONFIG_SPL_WATCHDOG_SUPPORT +#define CONFIG_SPL_DRIVERS_MISC_SUPPORT +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" +#define CONFIG_SPL_STACK 0x187FF0 +#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL_MMC_SUPPORT +#define CONFIG_SPL_BSS_START_ADDR 0x00180000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x2000/* 8 KB */ +#define CONFIG_SPL_STACK_R_ADDR 0x42300000 +#define CONFIG_SPL_STACK_R +#define CONFIG_SYS_SPL_MALLOC_START 0x42200000 +#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000/* 512 KB */ +#define CONFIG_SYS_ICACHE_OFF +#define CONFIG_SYS_DCACHE_OFF + +#define CONFIG_MALLOC_F_ADDR 0x182000/* malloc f used before GD_FLG_FULL_MALLOC_INIT */ + +#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */ + +#undef CONFIG_SPL_DM_PMIC +#undef CONFIG_SPL_DM_I2C +#undef CONFIG_SPL_DM_PMIC_BD71837 +#undef CONFIG_DM_USB +#undef CONFIG_SPL_DM_USB +#undef CONFIG_USB_DWC3_GENERIC +#undef CONFIG_DEVRES + +#define CONFIG_SYS_I2C + +#define CONFIG_POWER_BD71837 +#define CONFIG_POWER_BD71837_I2C_BUS 0 +#define CONFIG_POWER_BD71837_I2C_ADDR 0x4B + +#define CONFIG_SPL_DMA_SUPPORT + +#define CONFIG_SYS_FSL_USDHC_NUM 1 + +#else /* CONFIG_SPL_BUILD*/
include/configs/librem5.h line 77
Quoted 10 lines
include/configs/librem5.h new file +10
-0+ +#define CONFIG_SYS_FSL_USDHC_NUM 2 + +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 + +#define CONFIG_USBD_HS + +#define CONFIG_USB_GADGET_VBUS_DRAW 2 + +#endif /* CONFIG_SPL_BUILD*/
You can't use CONFIG_SPL_BUILD in this way. Symbols need to always be set (and yes, this likely came from some other bad example).
[snip]
include/configs/librem5.h line 131
Quoted 1 line
include/configs/librem5.h new file +1
-0+"bootargs=u_boot_version=" PLAIN_VERSION "\0" \
Why do you need this? It might be a problem for reproducible builds, and also you should just be able to use ${version} from the environment? Thanks.
Signature · 1 line
Tom
PATCH 6/13 board: librem5: add the u-boot source for the Librem5
In reply to Angus AinslieInitial commit of the Librem5 u-boot source
--- board/purism/librem5/librem5.c | 708 +++++++++++++++++++++++++++++++++ 1 file changed, 708 insertions(+) create mode 100644 board/purism/librem5/librem5.c
board/purism/librem5/librem5.c new file +708 -0
@@ -0,0 +1,708 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2018 NXP +* Copyright 2021 Purism +*/ + +#include <common.h> +#include <malloc.h> +#include <errno.h> +#include <asm/io.h> +#include <miiphy.h> +#include <asm/mach-imx/iomux-v3.h> +#include <asm-generic/gpio.h> +#include <asm/arch/sys_proto.h> +#include <fsl_esdhc.h> +#include <mmc.h> +#include <asm/arch/imx8mq_pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/mach-imx/gpio.h> +#include <asm/mach-imx/mxc_i2c.h> +#include <asm/arch/clock.h> +#include <asm/mach-imx/video.h> +#include <fuse.h> +#include <i2c.h> +#include <spl.h> +#include <usb.h> +#include <dwc3-uboot.h> +#include <linux/delay.h> +#include <linux/bitfield.h> +#include <usb/xhci.h> +#include "librem5.h" + +DECLARE_GLOBAL_DATA_PTR ; + +#define ENABLE_TPS_RESET + +#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE) + +static const iomux_v3_cfg_t wdog_pads[] = { +IMX8MQ_PAD_GPIO1_IO02__WDOG1_WDOG_B |MUX_PAD_CTRL (WDOG_PAD_CTRL ), +}; + +int board_early_init_f (void ) +{ +struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR ; + +log_debug ("%s: starting\n" , __func__); + +imx_iomux_v3_setup_multiple_pads (wdog_pads,ARRAY_SIZE (wdog_pads)); +set_wdog_reset (wdog); + +return 0 ; +} + +#ifdef CONFIG_OF_BOARD_SETUP +int ft_board_setup (void *blob,struct bd_info *bd) +{ +return 0 ; +} +#endif + +#ifdef CONFIG_BOARD_POSTCLK_INIT +int board_postclk_init (void ) +{ +/* TODO */ +return 0 ; +} +#endif + +#ifndef CONFIG_DM_USB +int usb_gadget_handle_interrupts (void ) +{ +dwc3_uboot_handle_interrupt (0 ); +return 0 ; +} + +#if defined(CONFIG_USB_DWC3 ) || defined(CONFIG_USB_XHCI_IMX8M ) +static void dwc3_nxp_usb_phy_init (struct dwc3_device *dwc3) +{ +u32 RegData; + + RegData =readl (dwc3->base +USB_PHY_CTRL1 ); + RegData &= ~(USB_PHY_CTRL1_VDATSRCENB0 |USB_PHY_CTRL1_VDATDETENB0 | +USB_PHY_CTRL1_COMMONONN ); + RegData |=USB_PHY_CTRL1_RESET |USB_PHY_CTRL1_ATERESET ; +writel (RegData, dwc3->base +USB_PHY_CTRL1 ); + + RegData =readl (dwc3->base +USB_PHY_CTRL0 ); + RegData |=USB_PHY_CTRL0_REF_SSP_EN ; +writel (RegData, dwc3->base +USB_PHY_CTRL0 ); + + RegData =readl (dwc3->base +USB_PHY_CTRL2 ); + RegData |=USB_PHY_CTRL2_TXENABLEN0 ; +writel (RegData, dwc3->base +USB_PHY_CTRL2 ); + + RegData =readl (dwc3->base +USB_PHY_CTRL1 ); + RegData &= ~(USB_PHY_CTRL1_RESET |USB_PHY_CTRL1_ATERESET ); +writel (RegData, dwc3->base +USB_PHY_CTRL1 ); +} + +static struct dwc3_device dwc3_device0_data = { +#ifdef CONFIG_SPL_BUILD + .maximum_speed =USB_SPEED_HIGH , +#else + .maximum_speed =USB_SPEED_SUPER , +#endif + .base =USB1_BASE_ADDR , + .dr_mode =USB_DR_MODE_PERIPHERAL , + .index =0 , + .dis_u2_susphy_quirk =1 , +}; + +static struct dwc3_device dwc3_device1_data = { +#ifdef CONFIG_SPL_BUILD + .maximum_speed =USB_SPEED_HIGH , +#else + .maximum_speed =USB_SPEED_SUPER , +#endif + .base =USB2_BASE_ADDR , + .dr_mode =USB_DR_MODE_HOST , + .index =1 , + .dis_u2_susphy_quirk =1 , +}; + +int board_usb_init (int index,enum usb_init_type init) +{ +int ret =0 ; + +imx8m_usb_power (index, true); + +if (index ==0 && init ==USB_INIT_DEVICE ) { +dwc3_nxp_usb_phy_init (&dwc3_device0_data); + ret =dwc3_uboot_init (&dwc3_device0_data); + } +if (index ==1 && init ==USB_INIT_HOST ) { +dwc3_nxp_usb_phy_init (&dwc3_device1_data); + ret =dwc3_uboot_init (&dwc3_device1_data); + } + +log_debug ("%s: ending %d\n" , __func__, ret); + +return ret; +} + +int board_usb_cleanup (int index,enum usb_init_type init) +{ +int ret =0 ; + +if (index ==0 && init ==USB_INIT_DEVICE ) +dwc3_uboot_exit (index); + +if (index ==1 && init ==USB_INIT_HOST ) +dwc3_uboot_exit (index); + +imx8m_usb_power (index, false); + +return ret; +} +#endif + +int xhci_hcd_init (int index,struct xhci_hccr **hccr,struct xhci_hcor **hcor) +{ +return 0 ; +} + +void xhci_hcd_stop (int index) +{ +} +#endif + +#ifdef CONFIG_LOAD_ENV_FROM_MMC_BOOT_PARTITION +uint board_mmc_get_env_part (struct mmc *mmc) +{ +log_debug ("%s: starting\n" , __func__); +uint part = (mmc->part_config >>3 ) &PART_ACCESS_MASK ; + +if (part ==7 ) + part =0 ; +return part; +} +#endif + +#define SPI_FLASH_CS IMX_GPIO_NR(5, 9) + +int board_spi_cs_gpio (unsigned int bus,unsigned int cs) +{ +return (bus ==0 && cs ==0 ) ? (SPI_FLASH_CS ) :-1 ; +} + +#define ECSPI_PAD_CTRL (PAD_CTL_DSE2 | PAD_CTL_HYS) + +static const iomux_v3_cfg_t ecspi_pads[] = { +IMX8MQ_PAD_ECSPI1_SCLK__ECSPI1_SCLK |MUX_PAD_CTRL (ECSPI_PAD_CTRL ), +IMX8MQ_PAD_ECSPI1_SS0__GPIO5_IO9 |MUX_PAD_CTRL (ECSPI_PAD_CTRL ), +IMX8MQ_PAD_ECSPI1_MOSI__ECSPI1_MOSI |MUX_PAD_CTRL (ECSPI_PAD_CTRL ), +IMX8MQ_PAD_ECSPI1_MISO__ECSPI1_MISO |MUX_PAD_CTRL (ECSPI_PAD_CTRL ), +}; + +/* used if we reset the TPS65982 */ +static const iomux_v3_cfg_t ecspi_pads_hiz[] = { +IMX8MQ_PAD_ECSPI1_SCLK__GPIO5_IO6 , +IMX8MQ_PAD_ECSPI1_MOSI__GPIO5_IO7 , +IMX8MQ_PAD_ECSPI1_MISO__GPIO5_IO8 , +IMX8MQ_PAD_ECSPI1_SS0__GPIO5_IO9 , +}; + +extern int set_clk_ecspi (int ); + +int board_ecspi_init (void ) +{ +log_debug ("%s: starting\n" , __func__); + +imx_iomux_v3_setup_multiple_pads (ecspi_pads,ARRAY_SIZE (ecspi_pads)); + +set_clk_ecspi (1 ); + +return 0 ; +} + +void ecspi_hiz (void ) +{ +log_debug ("%s: starting\n" , __func__); + +imx_iomux_v3_setup_multiple_pads (ecspi_pads_hiz,ARRAY_SIZE (ecspi_pads_hiz)); + +gpio_direction_input (SPI1_SCLK ); +gpio_direction_input (SPI1_MISO ); +gpio_direction_input (SPI1_MOSI ); +gpio_direction_input (SPI1_SS0 ); +} + +int bq_read_reg (int reg_index) +{ +struct udevice *udev, *bus; +u8 reg; +int ret; + + ret =uclass_get_device_by_seq (UCLASS_I2C ,3 , &bus); +if (ret) { +log_err ("%s: No bus %d\n" , __func__,3 ); +return -ENODEV ; + } + + ret =i2c_get_chip (bus,0x6a ,1 , &udev); +if (ret) { +log_err ("%s: setting chip offset failed %d\n" , __func__, ret); +return -EINVAL ; + } + +dm_i2c_read (udev, reg_index, ®,1 ); + +return reg; +} + +int bq_write_reg (int reg_index,u8 val) +{ +struct udevice *udev, *bus; +int ret; + + ret =uclass_get_device_by_seq (UCLASS_I2C ,3 , &bus); +if (ret) { +log_err ("%s: No bus %d\n" , __func__,3 ); +return 1 ; + } + + ret =i2c_get_chip (bus,0x6a ,1 , &udev); +if (ret) { +log_err ("%s: setting chip offset failed %d\n" , __func__, ret); +return 1 ; + } + +dm_i2c_write (udev, reg_index, &val,1 ); + +return 0 ; +} + +int read_vbat (void ) +{ +u8 reg02, reg03, reg0e; +int timeout =1000 ;// ms + +/* disable the charger and enable BAT_LOADEN to discharge the decoupling +* CAP +* https://e2e.ti.com/support/power-management/f/196/t/567401 +*/ + reg03 =bq_read_reg (0x03 ); +bq_write_reg (0x03 , (reg03 |0x80 ) & ~0x10 ); + +mdelay (10 ); + +/* force a conversion */ + reg02 =bq_read_reg (0x02 ); +bq_write_reg (0x02 , (reg02 |0x80 ) & ~0x40 ); + +do { +mdelay (10 ); + timeout -=10 ; + }while ((bq_read_reg (0x02 ) &0x80 ) && (timeout >0 )); + + reg0e =bq_read_reg (0x0e ); + +/* return the charger to it's original state */ +bq_write_reg (0x03 , reg03); +bq_write_reg (0x02 , reg02); + +return (reg0e &0x7f ) *20 +2304 ; +} + +int tps65982_wait_for_app (int timeout,int timeout_step) +{ +int ret; +char response[6 ]; +#ifdef CONFIG_DM_I2C +struct udevice *udev, *bus; +#endif + +log_debug ("%s: starting\n" , __func__); + +/* Set the i2c bus */ +#ifndef CONFIG_DM_I2C +log_debug ("%s: using i2c device mode\n" , __func__); +i2c_set_bus_num (0 ); +#else + ret =uclass_get_device_by_seq (UCLASS_I2C ,0 , &bus); +if (ret) { +log_err ("%s: No bus %d\n" , __func__,0 ); +return 1 ; + } + + ret =i2c_get_chip (bus,0x3f ,1 , &udev); +if (ret) { +log_err ("%s: setting chip offset failed %d\n" , __func__, ret); +return 1 ; + } +#endif + +while (timeout >0 ) { +#ifndef CONFIG_DM_I2C + ret =i2c_read (0x3f ,0x03 ,1 , (u8 *)response,5 ); +#else + ret =dm_i2c_read (udev,0x03 , (u8 *)response,5 ); +#endif +log_debug ("tps65982 mode %s\n" , response); +if (response[1 ] =='A' ) +return 0 ; +mdelay (timeout_step); + timeout -= timeout_step; +log_debug ("tps65982 waited %d ms %c\n" , timeout_step, response[1 ]); + } + +return 1 ; +} + +#define TPS_POWER_STATUS_PWROPMODE (x) FIELD_GET(GENMASK(3, 2), x) + +#define TPS_PDO_CONTRACT_TYPE (x) FIELD_GET(GENMASK(31, 30), x) +#define TPS_PDO_CONTRACT_FIXED 0 +#define TPS_PDO_CONTRACT_BATTERY 1 +#define TPS_PDO_CONTRACT_VARIABLE 2 + +#define TPS_TYPEC_PWR_MODE_USB 0 +#define TPS_TYPEC_PWR_MODE_1_5A 1 +#define TPS_TYPEC_PWR_MODE_3_0A 2 +#define TPS_TYPEC_PWR_MODE_PD 3 + +#define TPS_PDO_FIXED_CONTRACT_MAX_CURRENT (x) (FIELD_GET(GENMASK(9, 0), x) * 10) +#define TPS_PDO_VAR_CONTRACT_MAX_CURRENT (x) (FIELD_GET(GENMASK(9, 0), x) * 10) +#define TPS_PDO_BAT_CONTRACT_MAX_VOLTAGE (x) (FIELD_GET(GENMASK(29, 20), x) * 50) +#define TPS_PDO_BAT_CONTRACT_MAX_POWER (x) (FIELD_GET(GENMASK(9, 0), x) * 250) + +int tps65982_get_max_current (void ) +{ +int ret; +u8 buf[7 ]; +u8 pwr_status; +u32 contract; +int type, mode; +struct udevice *udev, *bus; + +log_debug ("%s: starting\n" , __func__); + +/* Set the i2c bus */ + ret =uclass_get_device_by_seq (UCLASS_I2C ,0 , &bus); +if (ret) { +log_debug ("%s: No bus %d\n" , __func__,0 ); +return -1 ; + } + + ret =i2c_get_chip (bus,0x3f ,1 , &udev); +if (ret) { +log_debug ("%s: setting chip offset failed %d\n" , __func__, ret); +return -1 ; + } + + ret =dm_i2c_read (udev,0x3f , buf,3 ); +if (ret) { +log_debug ("%s: reading pwr_status failed %d\n" , __func__, ret); +return -1 ; + } + + pwr_status = buf[1 ]; + +if (!(pwr_status &1 )) +return 0 ; + + mode =TPS_POWER_STATUS_PWROPMODE (pwr_status); +switch (mode) { +case TPS_TYPEC_PWR_MODE_1_5A : +return 1500 ; +case TPS_TYPEC_PWR_MODE_3_0A : +return 3000 ; +case TPS_TYPEC_PWR_MODE_PD : + ret =dm_i2c_read (udev,0x34 , buf,7 ); +if (ret) { +log_debug ("%s: reading active contract failed %d\n" , __func__, ret); +return -1 ; + } + + contract = buf[1 ] + (buf[2 ] <<8 ) + (buf[3 ] <<16 ) + (buf[4 ] <<24 ); + + type =TPS_PDO_CONTRACT_TYPE (contract); + +switch (type) { +case TPS_PDO_CONTRACT_FIXED : +return TPS_PDO_FIXED_CONTRACT_MAX_CURRENT (contract); +case TPS_PDO_CONTRACT_BATTERY : +return 1000 *TPS_PDO_BAT_CONTRACT_MAX_POWER (contract) + /TPS_PDO_BAT_CONTRACT_MAX_VOLTAGE (contract); +case TPS_PDO_CONTRACT_VARIABLE : +return TPS_PDO_VAR_CONTRACT_MAX_CURRENT (contract); +default : +log_debug ("Unknown contract type: %d\n" , type); +return -1 ; + } +case TPS_TYPEC_PWR_MODE_USB : +return 500 ; +default : +log_debug ("Unknown power mode: %d\n" , mode); +return -1 ; + } +} + +int init_tps65982 (void ) +{ +int vbat; + +log_debug ("%s: starting\n" , __func__); + +if (tps65982_wait_for_app (500 ,100 )) { +/* check that VBAT is present and greater than 3000 mV. resetting the +* tps65982 disconnects VBUS so we need a different power source. +* Battery voltage greater than 4.15V likely means the battery is not +* present. +*/ + vbat =read_vbat (); +#ifdef ENABLE_TPS_RESET +if (vbat >3000 && vbat <4150 ) { +log_info ("tps65982 attempting reset - %d mV\n" , vbat); +ecspi_hiz (); + +gpio_direction_output (TPS_RESET ,0 ); +mdelay (3 ); +gpio_direction_output (TPS_RESET ,1 ); +mdelay (2 ); +gpio_direction_output (TPS_RESET ,0 ); +mdelay (100 ); + +if (tps65982_wait_for_app (1000 ,250 )) { +log_err ("tps65982 failed to boot\n" ); +board_ecspi_init (); +gpio_direction_output (LED_G ,0 ); +gpio_direction_output (LED_R ,1 ); +return 1 ; + } + +board_ecspi_init (); + }else { +log_err ("vbat out of range to reset tps65982 %d mV\n" , vbat); +return 1 ; + } +#else +log_err ("tps65982 APP boot failed %d mV\n" , vbat); +return 1 ; +#endif + } + +log_info ("tps65982 boot successful\n" ); +return 0 ; +} + +int bq25896_set_iinlim (int current) +{ +u8 val, iinlim; +int ret; +struct udevice *udev, *bus; + +/* Set the i2c bus */ + ret =uclass_get_device_by_seq (UCLASS_I2C ,3 , &bus); +if (ret) { +log_err ("%s: No bus 3\n" , __func__); +return ret; + } + + ret =i2c_get_chip (bus,0x6a ,1 , &udev); +if (ret) { +log_err ("%s: setting chip offset failed %d\n" , __func__, ret); +return ret; + } + +if (current >3250 ) + current =3250 ; +if (current <100 ) + current =100 ; + + val =dm_i2c_reg_read (udev,0x00 ); + iinlim = ((current -100 ) /50 ) &0x3f ; + val = (val &0xc0 ) | iinlim; +dm_i2c_reg_write (udev,0x00 , val); +log_debug ("REG00 0x%x\n" , val); + +return 0 ; +} + +/* +* set some safe defaults for the battery charger +*/ +int init_charger_bq25896 (void ) +{ +u8 val; +int iinlim, vbat, ret; +struct udevice *udev, *bus; + +/* Set the i2c bus */ + ret =uclass_get_device_by_seq (UCLASS_I2C ,3 , &bus); +if (ret) { +log_debug ("%s: No bus 3\n" , __func__); +return ret; + } + + ret =i2c_get_chip (bus,0x6a ,1 , &udev); +if (ret) { +log_debug ("%s: setting chip offset failed %d\n" , __func__, ret); +return ret; + } + +/* enable automatic DC conversions */ + val =dm_i2c_reg_read (udev,0x02 ); +log_debug ("REG0B 0x%x\n" , val); + val = (val & ~0xc0 ) |0x40 ; +dm_i2c_reg_write (udev,0x02 , val); + +/* check VBUS good */ + val =dm_i2c_reg_read (udev,0x11 ); +log_debug ("VBUS good %d\n" , (val >>7 ) &1 ); +log_debug ("VBUS mV %d\n" , (val &0x7f ) *100 +2600 ); + + val =dm_i2c_reg_read (udev,0x0b ); +log_debug ("REG0B 0x%x\n" , val); + +log_debug ("VBUS_STAT 0x%x\n" , val >>5 ); +switch (val >>5 ) { +case 0 : +log_debug ("VBUS not detected\n" ); +break ; +case 1 : +log_debug ("USB SDP IINLIM 500mA\n" ); +break ; +case 2 : +log_debug ("USB CDP IINLIM 1500mA\n" ); +break ; +case 3 : +log_debug ("USB DCP IINLIM 3500mA\n" ); +break ; +case 4 : +log_debug ("MAXCHARGE IINLIM 1500mA\n" ); +break ; +case 5 : +log_debug ("Unknown IINLIM 500mA\n" ); +break ; +case 6 : +log_debug ("DIVIDER IINLIM > 1000mA\n" ); +break ; +case 7 : +log_debug ("OTG\n" ); +break ; + }; + +log_debug ("CHRG_STAT 0x%x\n" , (val >>3 ) &0x3 ); +log_debug ("PG_STAT 0x%x\n" , (val >>2 ) &1 ); +log_debug ("SDP_STAT 0x%x\n" , (val >>1 ) &1 ); +log_debug ("VSYS_STAT 0x%x\n" , val &1 ); + + val =dm_i2c_reg_read (udev,0x00 ); +log_debug ("REG00 0x%x\n" , val); + iinlim =100 + (val &0x3f ) *50 ; +log_debug ("IINLIM %d mA\n" , iinlim); +log_debug ("EN_HIZ 0x%x\n" , (val >>7 ) &1 ); +log_debug ("EN_ILIM 0x%x\n" , (val >>6 ) &1 ); + +/* check VBAT */ + vbat =read_vbat (); +log_debug ("VBAT mV %d\n" , vbat); + +if (vbat <2800 && iinlim <=500 ) { +/* battery voltage too low and +* insufficient current to boot linux. +*/ +gpio_direction_output (LED_R ,1 ); +log_err ("%s: voltage and current too low linux probably won't boot\n" , __func__); + } + +/* set 1.6A charge limit */ +dm_i2c_reg_write (udev,0x04 ,0x19 ); + +/* re-enable charger */ + val =dm_i2c_reg_read (udev,0x03 ); + val = val |0x10 ; +dm_i2c_reg_write (udev,0x03 , val); + +/* limit the VINDPM to 3.9V */ +dm_i2c_reg_write (udev,0x0d ,0x8d ); + +/* set the max voltage to 4.192V */ + val =dm_i2c_reg_read (udev,0x6 ); + val = (val & ~0xFC ) |0x16 <<2 ; +dm_i2c_reg_write (udev,0x6 , val); + +/* set the SYS_MIN to 3.7V */ + val =dm_i2c_reg_read (udev,0x3 ); + val = val |0xE ; +dm_i2c_reg_write (udev,0x3 , val); + +return 0 ; +} + +void init_usb_clk (void ); + +int board_init (void ) +{ +int tps_ret; + +log_debug ("%s: starting %d mV\n" , __func__,read_vbat ()); + +init_pinmux (); + +#if defined(CONFIG_USB_DWC3 ) || defined(CONFIG_USB_XHCI_IMX8M ) +log_debug ("%s: initializing USB clk\n" , __func__); +init_usb_clk (); +#endif + + tps_ret =init_tps65982 (); +init_charger_bq25896 (); + +if (!tps_ret) { +int current =tps65982_get_max_current (); + +if (current >500 ) +bq25896_set_iinlim (current); + } + +return 0 ; +} + +#define VOL_DOWN IMX_GPIO_NR(1, 17) + +int fastboot_key_pressed (void ) +{ +int val; + +gpio_direction_input (VOL_DOWN ); + + val =gpio_get_value (VOL_DOWN ); +log_debug ("%s : %d\n" , __func__, val); + +return !val; +} + +int board_late_init (void ) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG +u32 vid, rev; +char rev_str[3 ]; + +env_set ("board_name" ,"librem5" ); +if (fuse_read (8 ,2 , &vid) ||fuse_read (14 ,0 , &rev)) { +env_set ("board_rev" ,BOARD_REV_ERROR ); + }else if (vid ==0 ) { +env_set ("board_rev" ,BOARD_REV_UNKNOWN ); + }else if (vid == (PURISM_PID <<16 |PURISM_VID )) { +sprintf (rev_str,"%u" , rev); +env_set ("board_rev" , rev_str); + } + +printf ("Board name: %s\n" ,env_get ("board_name" )); +printf ("Board rev: %s\n" ,env_get ("board_rev" )); +#endif + +if (is_usb_boot ()) { +puts ("USB Boot\n" ); +env_set ("bootcmd" ,"fastboot 0" ); + }else if (fastboot_key_pressed ()) { +log_debug ("stop in u-boot\n" ); +env_set ("bootcmd" ,"" ); + } + +return 0 ; +} +
Signature · 1 line
2.25.1
PATCH 7/13 board: librem5: add the u-boot header for the Librem5
In reply to Angus AinslieInitial commit of the Librem5 u-boot header file
--- board/purism/librem5/librem5.h | 176 +++++++++++++++++++++++++++++++++ 1 file changed, 176 insertions(+) create mode 100644 board/purism/librem5/librem5.h
board/purism/librem5/librem5.h new file +176 -0
@@ -0,0 +1,176 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* +* Copyright 2021 Purism +*/ + +#ifndef __LIBREM5_H__ +#define __LIBREM5_H__ + +#define CAMERA_EN IMX_GPIO_NR(1, 0) +#define SD_EN IMX_GPIO_NR(1, 3) +#define AUDIO_EN IMX_GPIO_NR(1, 4) +#define DSI_EN IMX_GPIO_NR(1, 5) +#define SMC_EN IMX_GPIO_NR(1, 6) +#define TYPEC_MUX_EN IMX_GPIO_NR(1, 11) +#define HUB_NRESET IMX_GPIO_NR(1, 12) +#define HUB_EN IMX_GPIO_NR(1, 14) +#define VOL_UP IMX_GPIO_NR(1, 16) +#define VOL_DOWN IMX_GPIO_NR(1, 17) +#define DSI_BIAS_EN IMX_GPIO_NR(1, 20) +#define FLASH_EN IMX_GPIO_NR(1, 23) +#define WWAN_NRESET IMX_GPIO_NR(3, 1) +#define CHG_EN IMX_GPIO_NR(3, 2) +#define CHG_OTG_OUT_EN IMX_GPIO_NR(3, 4) +#define WIFI_EN IMX_GPIO_NR(3, 10) +#define GPS_EN IMX_GPIO_NR(3, 12) +#define BL_EN IMX_GPIO_NR(3, 14) +#define WWAN_EN IMX_GPIO_NR(3, 18) +#define NFC_EN IMX_GPIO_NR(4, 28) +#define LED_G IMX_GPIO_NR(5, 2) +#define LED_R IMX_GPIO_NR(5, 3) +#define LED_B IMX_GPIO_NR(1, 13) +#define MOTO IMX_GPIO_NR(5, 5) +#define SPI1_SCLK IMX_GPIO_NR(5, 6) +#define SPI1_MOSI IMX_GPIO_NR(5, 7) +#define SPI1_MISO IMX_GPIO_NR(5, 8) +#define SPI1_SS0 IMX_GPIO_NR(5, 9) + +#define UART1_TX IMX_GPIO_NR(5, 23) +#define UART1_RX IMX_GPIO_NR(5, 22) +#define UART2_TX IMX_GPIO_NR(5, 25) +#define UART2_RX IMX_GPIO_NR(5, 24) +#define UART3_TX IMX_GPIO_NR(5, 27) +#define UART3_RX IMX_GPIO_NR(5, 26) +#define UART4_TX IMX_GPIO_NR(5, 11) +#define UART4_RX IMX_GPIO_NR(5, 10) + +#define TPS_RESET IMX_GPIO_NR(3, 24) + +#define PURISM_VID 0x316d +#define PURISM_PID 0x4c05 + +#define BOARD_REV_ERROR "unknown" +#define BOARD_REV_BIRCH "1" +#define BOARD_REV_CHESTNUT "2" +#define BOARD_REV_DOGWOOD "3" +/* Could be ASPEN, BIRCH or CHESTNUT. assume CHESTNUT */ +#define BOARD_REV_UNKNOWN BOARD_REV_CHESTNUT + +#ifdef CONFIG_DM_GPIO +static inline void init_pinmux (void ) +{ +gpio_request (WIFI_EN ,"WIFI_EN" ); +#ifdef CONSOLE_ON_UART4 +gpio_direction_output (WIFI_EN ,1 ); +#else +gpio_direction_output (WIFI_EN ,0 ); +#endif /* CONSOLE_ON_UART4 */ +} +#else +static const iomux_v3_cfg_t configure_pads[] = { +IMX8MQ_PAD_GPIO1_IO00__GPIO1_IO0 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO03__GPIO1_IO3 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO04__GPIO1_IO4 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO05__GPIO1_IO5 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO06__GPIO1_IO6 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO11__GPIO1_IO11 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO12__GPIO1_IO12 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_GPIO1_IO14__GPIO1_IO14 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_ENET_MDC__GPIO1_IO16 |MUX_PAD_CTRL (PAD_CTL_PUE ), +IMX8MQ_PAD_ENET_MDIO__GPIO1_IO17 |MUX_PAD_CTRL (PAD_CTL_PUE ), +IMX8MQ_PAD_ENET_TD1__GPIO1_IO20 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_ENET_TXC__GPIO1_IO23 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_CE0_B__GPIO3_IO1 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_CE1_B__GPIO3_IO2 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_CE3_B__GPIO3_IO4 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_DATA04__GPIO3_IO10 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_DATA06__GPIO3_IO12 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_DQS__GPIO3_IO14 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_NAND_WP_B__GPIO3_IO18 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_SAI3_RXFS__GPIO4_IO28 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_SAI3_MCLK__GPIO5_IO2 |MUX_PAD_CTRL (PAD_CTL_DSE6 ), +IMX8MQ_PAD_SAI5_RXD3__GPIO3_IO24 , +}; + +static inline void init_pinmux (void ) +{ +imx_iomux_v3_setup_multiple_pads (configure_pads,ARRAY_SIZE (configure_pads)); + +gpio_request (LED_R ,"LED_R" ); +gpio_request (LED_G ,"LED_G" ); +gpio_request (LED_B ,"LED_B" ); +gpio_request (VOL_UP ,"VOL_UP" ); +gpio_request (VOL_DOWN ,"VOL_DOWN" ); + +gpio_request (NFC_EN ,"NFC_EN" ); +gpio_request (CHG_EN ,"CHG_EN" ); +gpio_request (CHG_OTG_OUT_EN ,"CHG_OTG_OUT_EN" ); + +gpio_request (TYPEC_MUX_EN ,"TYPEC_MUX_EN" ); + +gpio_request (TPS_RESET ,"TPS_RESET" ); + +gpio_request (WWAN_EN ,"WWAN_EN" ); +gpio_request (WWAN_NRESET ,"WWAN_NRESET" ); + +gpio_request (HUB_EN ,"HUB_EN" ); +gpio_request (HUB_NRESET ,"HUB_NRESET" ); +gpio_request (SD_EN ,"SD_EN" ); +gpio_request (AUDIO_EN ,"AUDIO_EN" ); +gpio_request (DSI_EN ,"DSI_EN" ); +gpio_request (SMC_EN ,"SMC_EN" ); +gpio_request (CAMERA_EN ,"CAMERA_EN" ); +gpio_request (FLASH_EN ,"FLASH_EN" ); +gpio_request (DSI_BIAS_EN ,"DSI_BIAS_EN" ); +gpio_request (GPS_EN ,"GPS_EN" ); +gpio_request (BL_EN ,"BL_EN" ); +#ifndef CONSOLE_ON_UART4 +gpio_request (WIFI_EN ,"WIFI_EN" ); +gpio_direction_output (WIFI_EN ,0 ); +#endif /* CONSOLE_ON_UART4 */ +gpio_direction_input (VOL_UP ); +gpio_direction_input (VOL_DOWN ); + +/* ensure charger is in the automated mode */ +gpio_direction_output (NFC_EN ,0 ); +gpio_direction_output (CHG_EN ,0 ); +gpio_direction_output (CHG_OTG_OUT_EN ,0 ); + +gpio_direction_input (TYPEC_MUX_EN ); + +gpio_direction_output (TPS_RESET ,0 ); + +gpio_direction_output (WWAN_EN ,0 ); +gpio_direction_output (WWAN_NRESET ,1 ); + +gpio_direction_output (HUB_EN ,0 ); +gpio_direction_output (HUB_NRESET ,1 ); +gpio_direction_output (SD_EN ,0 ); +gpio_direction_output (AUDIO_EN ,1 ); +gpio_direction_output (DSI_EN ,0 ); +gpio_direction_output (SMC_EN ,0 ); +gpio_direction_output (CAMERA_EN ,0 ); +gpio_direction_output (FLASH_EN ,0 ); +gpio_direction_output (DSI_BIAS_EN ,0 ); +gpio_direction_output (GPS_EN ,0 ); +gpio_direction_output (BL_EN ,0 ); +} +#endif /* CONFIG_DM_GPIO */ + +#define USB_PHY_CTRL0 0xF0040 +#define USB_PHY_CTRL0_REF_SSP_EN BIT(2) + +#define USB_PHY_CTRL1 0xF0044 +#define USB_PHY_CTRL1_RESET BIT(0) +#define USB_PHY_CTRL1_COMMONONN BIT(1) +#define USB_PHY_CTRL1_ATERESET BIT(3) +#define USB_PHY_CTRL1_VDATSRCENB0 BIT(19) +#define USB_PHY_CTRL1_VDATDETENB0 BIT(20) + +#define USB_PHY_CTRL2 0xF0048 +#define USB_PHY_CTRL2_TXENABLEN0 BIT(8) + +extern struct dram_timing_info dram_timing_b0; +extern int board_ecspi_init (void ); + +#endif
Signature · 1 line
2.25.1
PATCH 8/13 board: librem5: add the SPL source for the Librem5
In reply to Angus AinslieInitial commit of the Librem5 SPL source
--- board/purism/librem5/spl.c | 481 +++++++++++++++++++++++++++++++++++++ 1 file changed, 481 insertions(+) create mode 100644 board/purism/librem5/spl.c
board/purism/librem5/spl.c new file +481 -0
@@ -0,0 +1,481 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2018 NXP +* Copyright 2021 Purism +*/ + +#include <common.h> +#include <asm/io.h> +#include <errno.h> +#include <asm/io.h> +#include <asm/arch/ddr.h> +#include <asm/arch/imx8mq_pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/arch/clock.h> +#include <asm/mach-imx/boot_mode.h> +#include <asm/mach-imx/iomux-v3.h> +#include <asm/mach-imx/gpio.h> +#include <asm/mach-imx/mxc_i2c.h> +#include <fsl_esdhc_imx.h> +#include <mmc.h> +#include <power/pmic.h> +#include <power/bd71837.h> +#include <hang.h> +#include <init.h> +#include <spl.h> +#include <usb.h> +#include <dwc3-uboot.h> +#include <linux/delay.h> +#include "librem5.h" + +DECLARE_GLOBAL_DATA_PTR ; + +void spl_dram_init (void ) +{ +/* ddr init */ +if ((get_cpu_rev () &0xfff ) ==CHIP_REV_2_1 ) +ddr_init (&dram_timing); +else +ddr_init (&dram_timing_b0); +} + +int spl_board_boot_device (enum boot_device boot_dev_spl) +{ +log_debug ("%s : starting\n" , __func__); + +switch (boot_dev_spl) { +case SD1_BOOT : +case MMC1_BOOT : +return BOOT_DEVICE_MMC1 ; +case USB_BOOT : +return BOOT_DEVICE_BOARD ; +default : +return BOOT_DEVICE_NONE ; + } +} + +#define I2C_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_ODE | PAD_CTL_DSE7 | PAD_CTL_FSEL3) +#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) +struct i2c_pads_info i2c_pad_info1 = { + .scl = { + .i2c_mode =IMX8MQ_PAD_I2C1_SCL__I2C1_SCL |PC , + .gpio_mode =IMX8MQ_PAD_I2C1_SCL__GPIO5_IO14 |PC , + .gp =IMX_GPIO_NR (5 ,14 ), + }, + .sda = { + .i2c_mode =IMX8MQ_PAD_I2C1_SDA__I2C1_SDA |PC , + .gpio_mode =IMX8MQ_PAD_I2C1_SDA__GPIO5_IO15 |PC , + .gp =IMX_GPIO_NR (5 ,15 ), + }, +}; + +struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode =IMX8MQ_PAD_I2C2_SCL__I2C2_SCL |PC , + .gpio_mode =IMX8MQ_PAD_I2C2_SCL__GPIO5_IO16 |PC , + .gp =IMX_GPIO_NR (5 ,16 ), + }, + .sda = { + .i2c_mode =IMX8MQ_PAD_I2C2_SDA__I2C2_SDA |PC , + .gpio_mode =IMX8MQ_PAD_I2C2_SDA__GPIO5_IO17 |PC , + .gp =IMX_GPIO_NR (5 ,17 ), + }, +}; + +struct i2c_pads_info i2c_pad_info3 = { + .scl = { + .i2c_mode =IMX8MQ_PAD_I2C3_SCL__I2C3_SCL |PC , + .gpio_mode =IMX8MQ_PAD_I2C3_SCL__GPIO5_IO18 |PC , + .gp =IMX_GPIO_NR (5 ,18 ), + }, + .sda = { + .i2c_mode =IMX8MQ_PAD_I2C3_SDA__I2C3_SDA |PC , + .gpio_mode =IMX8MQ_PAD_I2C3_SDA__GPIO5_IO19 |PC , + .gp =IMX_GPIO_NR (5 ,19 ), + }, +}; + +struct i2c_pads_info i2c_pad_info4 = { + .scl = { + .i2c_mode =IMX8MQ_PAD_I2C4_SCL__I2C4_SCL |PC , + .gpio_mode =IMX8MQ_PAD_I2C4_SCL__GPIO5_IO20 |PC , + .gp =IMX_GPIO_NR (5 ,20 ), + }, + .sda = { + .i2c_mode =IMX8MQ_PAD_I2C4_SDA__I2C4_SDA |PC , + .gpio_mode =IMX8MQ_PAD_I2C4_SDA__GPIO5_IO21 |PC , + .gp =IMX_GPIO_NR (5 ,21 ), + }, +}; + +#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1) + +static const iomux_v3_cfg_t uart_pads[] = { +IMX8MQ_PAD_UART1_RXD__UART1_RX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_UART1_TXD__UART1_TX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_UART2_RXD__UART2_RX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_UART2_TXD__UART2_TX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_UART3_RXD__UART3_RX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_UART3_TXD__UART3_TX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_ECSPI2_SCLK__UART4_RX |MUX_PAD_CTRL (UART_PAD_CTRL ), +IMX8MQ_PAD_ECSPI2_MOSI__UART4_TX |MUX_PAD_CTRL (UART_PAD_CTRL ), +}; + +#define USDHC1_PWR_GPIO IMX_GPIO_NR(2, 10) +#define USDHC2_PWR_GPIO IMX_GPIO_NR(2, 19) + +int board_mmc_getcd (struct mmc *mmc) +{ +struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; +int ret =0 ; + +switch (cfg->esdhc_base) { +case USDHC1_BASE_ADDR : + ret =1 ; +break ; +case USDHC2_BASE_ADDR : + ret =1 ; +break ; + } + +return ret; +} + +#define USDHC_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_HYS | PAD_CTL_PUE | \ + PAD_CTL_FSEL1) +#define USDHC_GPIO_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_DSE1) + +static const iomux_v3_cfg_t usdhc1_pads[] = { +IMX8MQ_PAD_SD1_CLK__USDHC1_CLK |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_CMD__USDHC1_CMD |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA0__USDHC1_DATA0 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA1__USDHC1_DATA1 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA2__USDHC1_DATA2 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA3__USDHC1_DATA3 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA4__USDHC1_DATA4 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA5__USDHC1_DATA5 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA6__USDHC1_DATA6 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_DATA7__USDHC1_DATA7 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +IMX8MQ_PAD_SD1_RESET_B__GPIO2_IO10 |MUX_PAD_CTRL (NO_PAD_CTRL ), +}; + +static const iomux_v3_cfg_t usdhc2_pads[] = { +IMX8MQ_PAD_SD2_CLK__USDHC2_CLK |MUX_PAD_CTRL (USDHC_PAD_CTRL ),/* 0xd6 */ +IMX8MQ_PAD_SD2_CMD__USDHC2_CMD |MUX_PAD_CTRL (USDHC_PAD_CTRL ),/* 0xd6 */ +IMX8MQ_PAD_SD2_DATA0__USDHC2_DATA0 |MUX_PAD_CTRL (USDHC_PAD_CTRL ),/* 0xd6 */ +IMX8MQ_PAD_SD2_DATA1__USDHC2_DATA1 |MUX_PAD_CTRL (USDHC_PAD_CTRL ),/* 0xd6 */ +IMX8MQ_PAD_SD2_DATA2__USDHC2_DATA2 |MUX_PAD_CTRL (USDHC_PAD_CTRL ),/* 0x16 */ +IMX8MQ_PAD_SD2_DATA3__USDHC2_DATA3 |MUX_PAD_CTRL (USDHC_PAD_CTRL ),/* 0xd6 */ +IMX8MQ_PAD_SD2_RESET_B__GPIO2_IO19 |MUX_PAD_CTRL (USDHC_GPIO_PAD_CTRL ), +}; + +static struct fsl_esdhc_cfg usdhc_cfg[2 ] = { + {USDHC1_BASE_ADDR ,0 ,8 }, +#ifndef CONFIG_SPL_BUILD + {USDHC2_BASE_ADDR ,0 ,4 }, +#endif +}; + +int board_mmc_init (struct bd_info *bis) +{ +int i, ret; +/* +* According to the board_mmc_init() the following map is done: +* (U-Boot device node) (Physical Port) +* mmc0 USDHC1 +* mmc1 USDHC2 +*/ +for (i =0 ; i <CONFIG_SYS_FSL_USDHC_NUM ; i++) { +log_debug ("Initializing FSL USDHC port %d\n" , i); +switch (i) { +case 0 : +init_clk_usdhc (0 ); + usdhc_cfg[0 ].sdhc_clk =mxc_get_clock (USDHC1_CLK_ROOT ); +imx_iomux_v3_setup_multiple_pads (usdhc1_pads, +ARRAY_SIZE (usdhc1_pads)); +gpio_request (USDHC1_PWR_GPIO ,"usdhc1_reset" ); +gpio_direction_output (USDHC1_PWR_GPIO ,0 ); +udelay (500 ); +gpio_direction_output (USDHC1_PWR_GPIO ,1 ); +break ; +case 1 : +init_clk_usdhc (1 ); + usdhc_cfg[1 ].sdhc_clk =mxc_get_clock (USDHC2_CLK_ROOT ); +imx_iomux_v3_setup_multiple_pads (usdhc2_pads, +ARRAY_SIZE (usdhc2_pads)); +gpio_request (USDHC2_PWR_GPIO ,"usdhc2_reset" ); +gpio_direction_output (USDHC2_PWR_GPIO ,0 ); +udelay (500 ); +gpio_direction_output (USDHC2_PWR_GPIO ,1 ); +break ; +default : +log_err ("Warning: USDHC controller(%d) not supported\n" , i +1 ); +return -EINVAL ; + } + + ret =fsl_esdhc_initialize (bis, &usdhc_cfg[i]); +if (ret) +return ret; + } + +return 0 ; +} + +#define LDO_VOLT_EN BIT(6) + +/* +* Disable the charger - it will be re-enabled in u-boot +*/ +void disable_charger_bq25896 (void ) +{ +u8 val; +int timeout =1000 ;// ms + +/* Set the i2c bus */ +i2c_set_bus_num (3 ); + +/* disable ship mode if BATFET_DLY is set */ + val =i2c_reg_read (0x6a ,0x09 ); +log_debug ("REG09 0x%x\n" , val); +if (val &0x28 ) { + val = val & ~0x28 ; +i2c_reg_write (0x6a ,0x09 , val); + } + +/* disable and trigger DPDM, ICO, HVDCP and MaxCharge */ + val =i2c_reg_read (0x6a ,0x02 ); +log_debug ("REG02 0x%x\n" , val); + val &=0xe0 ; +i2c_reg_write (0x6a ,0x02 , val); + +/* disable charger and enable BAT_LOADEN */ + val =i2c_reg_read (0x6a ,0x03 ); +log_debug ("REG03 0x%x\n" , val); + val = (val |0x80 ) & ~0x10 ; +i2c_reg_write (0x6a ,0x03 , val); + +mdelay (10 ); + +/* force ADC conversions */ + val =i2c_reg_read (0x6a ,0x02 ); +log_debug ("REG02 0x%x\n" , val); + val = (val |0x80 ) & ~0x40 ; +i2c_reg_write (0x6a ,0x02 , val); + +do { +mdelay (10 ); + timeout -=10 ; + }while ((i2c_reg_read (0x6a ,0x02 ) &0x80 ) && (timeout >0 )); + +/* enable STAT pin */ + val =i2c_reg_read (0x6a ,0x07 ); +log_debug ("REG07 0x%x\n" , val); + val = val & ~0x40 ; +i2c_reg_write (0x6a ,0x07 , val); + +/* check VBUS */ + val =i2c_reg_read (0x6a ,0x11 ); +log_debug ("VBUS good %d\n" , (val >>7 ) &1 ); +log_debug ("VBUS mV %d\n" , (val &0x7f ) *100 +2600 ); + +/* check VBAT */ + val =i2c_reg_read (0x6a ,0x0e ); +log_debug ("VBAT mV %d\n" , (val &0x7f ) *20 +2304 ); + +/* limit the VINDPM to 3.9V */ +i2c_reg_write (0x6a ,0x0d ,0x8d ); + +/* set the max voltage to 4.192V */ + val =i2c_reg_read (0x6a ,0x6 ); + val = (val & ~0xFC ) |0x16 <<2 ; +i2c_reg_write (0x6a ,0x6 , val); + +/* set the SYS_MIN to 3.7V */ + val =i2c_reg_read (0x6a ,0x3 ); + val = val |0xE ; +i2c_reg_write (0x6a ,0x3 , val); + +/* disable BAT_LOADEN */ + val =i2c_reg_read (0x6a ,0x03 ); +log_debug ("REG03 0x%x\n" , val); + val = val & ~0x80 ; +i2c_reg_write (0x6a ,0x03 , val); +} + +#define I2C_PMIC 0 + +int power_bd71837_init (unsigned char bus) +{ +static const char name[] =BD718XX_REGULATOR_DRIVER ; +struct pmic *p =pmic_alloc (); + +if (!p) { +log_err ("%s: POWER allocation error!\n" , __func__); +return -ENOMEM ; + } + + p->name = name; + p->interface =I2C_PMIC ; + p->number_of_regs =BD718XX_MAX_REGISTER ; + p->hw.i2c.addr =CONFIG_POWER_BD71837_I2C_ADDR ; + p->hw.i2c.tx_num =1 ; + p->bus = bus; + +return 0 ; +} + +int power_init_board (void ) +{ +struct pmic *p; +int ldo[] = {BD718XX_LDO5_VOLT ,BD718XX_LDO6_VOLT , +BD71837_LDO7_VOLT }; +u32 val; +int i, rv; + +/* Set the i2c bus */ +setup_i2c (0 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info1); + +/* +* Init PMIC +*/ + rv =power_bd71837_init (CONFIG_POWER_BD71837_I2C_BUS ); +if (rv) { +log_err ("%s: power_bd71837_init(%d) error %d\n" , __func__, +CONFIG_POWER_BD71837_I2C_BUS , rv); + goto out; + } + + p =pmic_get (BD718XX_REGULATOR_DRIVER ); +if (!p) { +log_err ("%s: pmic_get(%s) failed\n" , __func__,BD718XX_REGULATOR_DRIVER ); + rv = -ENODEV ; + goto out; + } + + rv =pmic_probe (p); +if (rv) { +log_err ("%s: pmic_probe() error %d\n" , __func__, rv); + goto out; + } + +/* +* Unlock all regs +*/ +pmic_reg_write (p,BD718XX_REGLOCK ,0 ); + +/* find the reset cause */ +pmic_reg_read (p,0x29 , &val); +log_debug ("%s: reset cause %d\n" , __func__, val); + +/* +* Reconfigure default voltages and disable: +* - BUCK3: VDD_GPU_0V9 (1.00 -> 0.90) +* - BUCK4: VDD_VPU_0V9 (1.00 -> 0.90) +*/ +pmic_reg_write (p,BD71837_BUCK3_VOLT_RUN ,0x14 ); +pmic_reg_write (p,BD71837_BUCK4_VOLT_RUN ,0x14 ); + +/* +* Enable PHYs voltages: LDO5-7 +*/ +for (i =0 ; i <ARRAY_SIZE (ldo); i++) { + rv =pmic_reg_read (p, ldo[i], &val); +if (rv) { +log_err ("%s: pmic_read(%x) error %d\n" , __func__, + ldo[i], rv); +continue ; + } + +pmic_reg_write (p, ldo[i], val |LDO_VOLT_EN ); + } + +udelay (500 ); + + rv =0 ; +out: +return rv; +} + +void spl_board_init (void ) +{ +init_usb_clk (); + +if (is_usb_boot ()) +puts ("USB Boot\n" ); +else +puts ("Normal Boot\n" ); +} + +void board_boot_order (u32 *spl_boot_list) +{ +if (is_usb_boot ()) + spl_boot_list[0 ] =BOOT_DEVICE_BOARD ; +else + spl_boot_list[0 ] =BOOT_DEVICE_MMC1 ; +} + +int board_fit_config_name_match (const char *name) +{ +/* Just empty function now - can't decide what to choose */ +return 0 ; +} + +void board_init_f (ulong dummy) +{ +int ret; + +/* Clear global data */ +memset ((void *)gd,0 ,sizeof (gd_t)); + +arch_cpu_init (); + +init_uart_clk (CONSOLE_UART_CLK ); +imx_iomux_v3_setup_multiple_pads (uart_pads,ARRAY_SIZE (uart_pads)); + +#ifdef CONSOLE_ON_UART4 +gpio_request (WIFI_EN ,"WIFI_EN" ); +gpio_direction_output (WIFI_EN ,1 ); +#endif + +board_early_init_f (); + +timer_init (); + +preloader_console_init (); + +/* Clear the BSS. */ +memset (__bss_start,0 , __bss_end - __bss_start); + + ret =spl_init (); +if (ret) { +log_err ("spl_init() failed: %d\n" , ret); +hang (); + } + +enable_tzc380 (); + +printf ("Initializing pinmux\n" ); +init_pinmux (); +gpio_direction_output (LED_G ,1 ); +gpio_direction_output (MOTO ,1 ); +mdelay (50 ); +gpio_direction_output (MOTO ,0 ); + +/* Enable and configure i2c buses not used below */ +setup_i2c (1 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info2); +setup_i2c (2 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info3); +setup_i2c (3 ,CONFIG_SYS_I2C_SPEED ,0x7f , &i2c_pad_info4); + +power_init_board (); + +disable_charger_bq25896 (); + +/* initialize this for M4 even if u-boot doesn't have SF_CMD */ +printf ("Initializing ECSPI\n" ); +board_ecspi_init (); + +/* DDR initialization */ +printf ("Initializing DRAM\n" ); +spl_dram_init (); +} +
Signature · 1 line
2.25.1
PATCH 9/13 board: librem5: add the LPDDR4 source for the Librem5
In reply to Angus AinslieThis is a copy of imx8mq LPDDR4 source files
--- board/purism/librem5/lpddr4_timing.c | 1324 +++++++++++++++++++++++ board/purism/librem5/lpddr4_timing_b0.c | 1191 ++++++++++++++++++++ 2 files changed, 2515 insertions(+) create mode 100644 board/purism/librem5/lpddr4_timing.c create mode 100644 board/purism/librem5/lpddr4_timing_b0.c
board/purism/librem5/lpddr4_timing.c new file +1324 -0
@@ -0,0 +1,1324 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright 2018 NXP +*/ + +#include <linux/kernel.h> +#include <common.h> +#include <asm/arch/ddr.h> +#include <asm/arch/lpddr4_define.h> + +#define WR_POST_EXT_3200 /* recommened to define */ + +struct dram_cfg_param lpddr4_ddrc_cfg[] = { +/* Start to config, default 3200mbps */ + {DDRC_DBG1 (0 ),0x00000001 }, + {DDRC_PWRCTL (0 ),0x00000001 }, + {DDRC_MSTR (0 ),0xa3080020 }, + {DDRC_MSTR2 (0 ),0x00000000 }, + {DDRC_RFSHTMG (0 ),0x006100E0 }, + {DDRC_INIT0 (0 ),0xC003061B }, + {DDRC_INIT1 (0 ),0x009D0000 }, + {DDRC_INIT3 (0 ),0x00D4002D }, +#ifdef WR_POST_EXT_3200 + {DDRC_INIT4 (0 ),0x00330008 }, +#else + {DDRC_INIT4 (0 ),0x00310008 }, +#endif + {DDRC_INIT6 (0 ),0x0066004a }, + {DDRC_INIT7 (0 ),0x0006004a }, + + {DDRC_DRAMTMG0 (0 ),0x1A201B22 }, + {DDRC_DRAMTMG1 (0 ),0x00060633 }, + {DDRC_DRAMTMG3 (0 ),0x00C0C000 }, + {DDRC_DRAMTMG4 (0 ),0x0F04080F }, + {DDRC_DRAMTMG5 (0 ),0x02040C0C }, + {DDRC_DRAMTMG6 (0 ),0x01010007 }, + {DDRC_DRAMTMG7 (0 ),0x00000401 }, + {DDRC_DRAMTMG12 (0 ),0x00020600 }, + {DDRC_DRAMTMG13 (0 ),0x0C100002 }, + {DDRC_DRAMTMG14 (0 ),0x000000E6 }, + {DDRC_DRAMTMG17 (0 ),0x00A00050 }, + + {DDRC_ZQCTL0 (0 ),0x03200018 }, + {DDRC_ZQCTL1 (0 ),0x028061A8 }, + {DDRC_ZQCTL2 (0 ),0x00000000 }, + + {DDRC_DFITMG0 (0 ),0x0497820A }, + {DDRC_DFITMG1 (0 ),0x00080303 }, + {DDRC_DFIUPD0 (0 ),0xE0400018 }, + {DDRC_DFIUPD1 (0 ),0x00DF00E4 }, + {DDRC_DFIUPD2 (0 ),0x80000000 }, + {DDRC_DFIMISC (0 ),0x00000011 }, + {DDRC_DFITMG2 (0 ),0x0000170A }, + + {DDRC_DBICTL (0 ),0x00000001 }, + {DDRC_DFIPHYMSTR (0 ),0x00000001 }, + {DDRC_RANKCTL (0 ),0x00000c99 }, + {DDRC_DRAMTMG2 (0 ),0x070E171a }, + +/* address mapping */ + {DDRC_ADDRMAP0 (0 ),0x00000015 }, + {DDRC_ADDRMAP3 (0 ),0x00000000 }, + {DDRC_ADDRMAP4 (0 ),0x00001F1F }, +/* bank interleave */ + {DDRC_ADDRMAP1 (0 ),0x00080808 }, + {DDRC_ADDRMAP5 (0 ),0x07070707 }, + {DDRC_ADDRMAP6 (0 ),0x08080707 }, + +/* performance setting */ + {DDRC_ODTCFG (0 ),0x0b060908 }, + {DDRC_ODTMAP (0 ),0x00000000 }, + {DDRC_SCHED (0 ),0x29511505 }, + {DDRC_SCHED1 (0 ),0x0000002c }, + {DDRC_PERFHPR1 (0 ),0x5900575b }, +/* 150T starve and 0x90 max tran len */ + {DDRC_PERFLPR1 (0 ),0x90000096 }, +/* 300T starve and 0x10 max tran len */ + {DDRC_PERFWR1 (0 ),0x1000012c }, + {DDRC_DBG0 (0 ),0x00000016 }, + {DDRC_DBG1 (0 ),0x00000000 }, + {DDRC_DBGCMD (0 ),0x00000000 }, + {DDRC_SWCTL (0 ),0x00000001 }, + {DDRC_POISONCFG (0 ),0x00000011 }, + {DDRC_PCCFG (0 ),0x00000111 }, + {DDRC_PCFGR_0 (0 ),0x000010f3 }, + {DDRC_PCFGW_0 (0 ),0x000072ff }, + {DDRC_PCTRL_0 (0 ),0x00000001 }, +/* disable Read Qos*/ + {DDRC_PCFGQOS0_0 (0 ),0x00000e00 }, + {DDRC_PCFGQOS1_0 (0 ),0x0062ffff }, +/* disable Write Qos*/ + {DDRC_PCFGWQOS0_0 (0 ),0x00000e00 }, + {DDRC_PCFGWQOS1_0 (0 ),0x0000ffff }, + +/* Frequency 1: 400mbps */ + {DDRC_FREQ1_DRAMTMG0 (0 ),0x0d0b010c }, + {DDRC_FREQ1_DRAMTMG1 (0 ),0x00030410 }, + {DDRC_FREQ1_DRAMTMG2 (0 ),0x0305090c }, + {DDRC_FREQ1_DRAMTMG3 (0 ),0x00505006 }, + {DDRC_FREQ1_DRAMTMG4 (0 ),0x05040305 }, + {DDRC_FREQ1_DRAMTMG5 (0 ),0x0d0e0504 }, + {DDRC_FREQ1_DRAMTMG6 (0 ),0x0a060004 }, + {DDRC_FREQ1_DRAMTMG7 (0 ),0x0000090e }, + {DDRC_FREQ1_DRAMTMG14 (0 ),0x00000032 }, + {DDRC_FREQ1_DRAMTMG15 (0 ),0x00000000 }, + {DDRC_FREQ1_DRAMTMG17 (0 ),0x0036001b }, + {DDRC_FREQ1_DERATEINT (0 ),0x7e9fbeb1 }, + {DDRC_FREQ1_DFITMG0 (0 ),0x03818200 }, + {DDRC_FREQ1_DFITMG2 (0 ),0x00000000 }, + {DDRC_FREQ1_RFSHTMG (0 ),0x000C001c }, + {DDRC_FREQ1_INIT3 (0 ),0x00840000 }, + {DDRC_FREQ1_INIT4 (0 ),0x00310008 }, + {DDRC_FREQ1_INIT6 (0 ),0x0066004a }, + {DDRC_FREQ1_INIT7 (0 ),0x0006004a }, + +/* Frequency 2: 100mbps */ + {DDRC_FREQ2_DRAMTMG0 (0 ),0x0d0b010c }, + {DDRC_FREQ2_DRAMTMG1 (0 ),0x00030410 }, + {DDRC_FREQ2_DRAMTMG2 (0 ),0x0305090c }, + {DDRC_FREQ2_DRAMTMG3 (0 ),0x00505006 }, + {DDRC_FREQ2_DRAMTMG4 (0 ),0x05040305 }, + {DDRC_FREQ2_DRAMTMG5 (0 ),0x0d0e0504 }, + {DDRC_FREQ2_DRAMTMG6 (0 ),0x0a060004 }, + {DDRC_FREQ2_DRAMTMG7 (0 ),0x0000090e }, + {DDRC_FREQ2_DRAMTMG14 (0 ),0x00000032 }, + {DDRC_FREQ2_DRAMTMG17 (0 ),0x0036001b }, + {DDRC_FREQ2_DERATEINT (0 ),0x7e9fbeb1 }, + {DDRC_FREQ2_DFITMG0 (0 ),0x03818200 }, + {DDRC_FREQ2_DFITMG2 (0 ),0x00000000 }, + {DDRC_FREQ2_RFSHTMG (0 ),0x00030007 }, + {DDRC_FREQ2_INIT3 (0 ),0x00840000 }, + {DDRC_FREQ2_INIT4 (0 ),0x00310008 }, + {DDRC_FREQ2_INIT6 (0 ),0x0066004a }, + {DDRC_FREQ2_INIT7 (0 ),0x0006004a }, +}; + +/* PHY Initialize Configuration */ +struct dram_cfg_param lpddr4_ddrphy_cfg[] = { + {0x20110 ,0x02 }, + {0x20111 ,0x03 }, + {0x20112 ,0x04 }, + {0x20113 ,0x05 }, + {0x20114 ,0x00 }, + {0x20115 ,0x01 }, + + {0x1005f ,0x1ff }, + {0x1015f ,0x1ff }, + {0x1105f ,0x1ff }, + {0x1115f ,0x1ff }, + {0x1205f ,0x1ff }, + {0x1215f ,0x1ff }, + {0x1305f ,0x1ff }, + {0x1315f ,0x1ff }, + + {0x11005f ,0x1ff }, + {0x11015f ,0x1ff }, + {0x11105f ,0x1ff }, + {0x11115f ,0x1ff }, + {0x11205f ,0x1ff }, + {0x11215f ,0x1ff }, + {0x11305f ,0x1ff }, + {0x11315f ,0x1ff }, + + {0x21005f ,0x1ff }, + {0x21015f ,0x1ff }, + {0x21105f ,0x1ff }, + {0x21115f ,0x1ff }, + {0x21205f ,0x1ff }, + {0x21215f ,0x1ff }, + {0x21305f ,0x1ff }, + {0x21315f ,0x1ff }, + + {0x55 ,0x1ff }, + {0x1055 ,0x1ff }, + {0x2055 ,0x1ff }, + {0x3055 ,0x1ff }, + {0x4055 ,0x1ff }, + {0x5055 ,0x1ff }, + {0x6055 ,0x1ff }, + {0x7055 ,0x1ff }, + {0x8055 ,0x1ff }, + {0x9055 ,0x1ff }, + + {0x200c5 ,0x19 }, + {0x1200c5 ,0x7 }, + {0x2200c5 ,0x7 }, + + {0x2002e ,0x2 }, + {0x12002e ,0x2 }, + {0x22002e ,0x2 }, + + {0x90204 ,0x0 }, + {0x190204 ,0x0 }, + {0x290204 ,0x0 }, + +#ifdef WR_POST_EXT_3200 + {0x20024 ,0xeb }, +#else + {0x20024 ,0xab }, +#endif + {0x2003a ,0x0 }, + {0x120024 ,0xab }, + {0x2003a ,0x0 }, + {0x220024 ,0xab }, + {0x2003a ,0x0 }, + {0x20056 ,0x3 }, + {0x120056 ,0xa }, + {0x220056 ,0xa }, + {0x1004d ,0xe00 }, + {0x1014d ,0xe00 }, + {0x1104d ,0xe00 }, + {0x1114d ,0xe00 }, + {0x1204d ,0xe00 }, + {0x1214d ,0xe00 }, + {0x1304d ,0xe00 }, + {0x1314d ,0xe00 }, + {0x11004d ,0xe00 }, + {0x11014d ,0xe00 }, + {0x11104d ,0xe00 }, + {0x11114d ,0xe00 }, + {0x11204d ,0xe00 }, + {0x11214d ,0xe00 }, + {0x11304d ,0xe00 }, + {0x11314d ,0xe00 }, + {0x21004d ,0xe00 }, + {0x21014d ,0xe00 }, + {0x21104d ,0xe00 }, + {0x21114d ,0xe00 }, + {0x21204d ,0xe00 }, + {0x21214d ,0xe00 }, + {0x21304d ,0xe00 }, + {0x21314d ,0xe00 }, + + {0x10049 ,0xfbe }, + {0x10149 ,0xfbe }, + {0x11049 ,0xfbe }, + {0x11149 ,0xfbe }, + {0x12049 ,0xfbe }, + {0x12149 ,0xfbe }, + {0x13049 ,0xfbe }, + {0x13149 ,0xfbe }, + {0x110049 ,0xfbe }, + {0x110149 ,0xfbe }, + {0x111049 ,0xfbe }, + {0x111149 ,0xfbe }, + {0x112049 ,0xfbe }, + {0x112149 ,0xfbe }, + {0x113049 ,0xfbe }, + {0x113149 ,0xfbe }, + {0x210049 ,0xfbe }, + {0x210149 ,0xfbe }, + {0x211049 ,0xfbe }, + {0x211149 ,0xfbe }, + {0x212049 ,0xfbe }, + {0x212149 ,0xfbe }, + {0x213049 ,0xfbe }, + {0x213149 ,0xfbe }, + + {0x43 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x1043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x2043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x3043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x4043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x5043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x6043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x7043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x8043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + {0x9043 , ((LPDDR4_PHY_ADDR_RON <<5 ) |LPDDR4_PHY_ADDR_RON ) }, + + {0x20018 ,0x3 }, + {0x20075 ,0x4 }, + {0x20050 ,0x0 }, + {0x20008 ,0x320 }, + {0x120008 ,0x64 }, + {0x220008 ,0x19 }, + {0x20088 ,0x9 }, + {0x200b2 ,0x104 }, + {0x10043 ,0x5a1 }, + {0x10143 ,0x5a1 }, + {0x11043 ,0x5a1 }, + {0x11143 ,0x5a1 }, + {0x12043 ,0x5a1 }, + {0x12143 ,0x5a1 }, + {0x13043 ,0x5a1 }, + {0x13143 ,0x5a1 }, + {0x1200b2 ,0x104 }, + {0x110043 ,0x5a1 }, + {0x110143 ,0x5a1 }, + {0x111043 ,0x5a1 }, + {0x111143 ,0x5a1 }, + {0x112043 ,0x5a1 }, + {0x112143 ,0x5a1 }, + {0x113043 ,0x5a1 }, + {0x113143 ,0x5a1 }, + {0x2200b2 ,0x104 }, + {0x210043 ,0x5a1 }, + {0x210143 ,0x5a1 }, + {0x211043 ,0x5a1 }, + {0x211143 ,0x5a1 }, + {0x212043 ,0x5a1 }, + {0x212143 ,0x5a1 }, + {0x213043 ,0x5a1 }, + {0x213143 ,0x5a1 }, + {0x200fa ,0x1 }, + {0x1200fa ,0x1 }, + {0x2200fa ,0x1 }, + {0x20019 ,0x1 }, + {0x120019 ,0x1 }, + {0x220019 ,0x1 }, + {0x200f0 ,0x660 }, + {0x200f1 ,0x0 }, + {0x200f2 ,0x4444 }, + {0x200f3 ,0x8888 }, + {0x200f4 ,0x5665 }, + {0x200f5 ,0x0 }, + {0x200f6 ,0x0 }, + {0x200f7 ,0xf000 }, + {0x20025 ,0x0 }, + {0x2002d ,0x0 }, + {0x12002d ,0x0 }, + {0x22002d ,0x0 }, + + {0x200c7 ,0x80 }, + {0x1200c7 ,0x80 }, + {0x2200c7 ,0x80 }, + {0x200ca ,0x106 }, + {0x1200ca ,0x106 }, + {0x2200ca ,0x106 }, +}; + +/* P0 message block paremeter for training firmware */ +struct dram_cfg_param lpddr4_fsp0_cfg[] = { + {0xd0000 ,0x0 }, + {0x54000 ,0x0 }, + {0x54001 ,0x0 }, + {0x54002 ,0x0 }, + {0x54003 ,0xc80 }, + {0x54004 ,0x2 }, + {0x54005 , ((LPDDR4_PHY_RON <<8 ) |LPDDR4_PHY_RTT ) },/* PHY Ron/Rtt */ + {0x54006 ,LPDDR4_PHY_VREF_VALUE }, + {0x54007 ,0x0 }, + {0x54008 ,0x131f }, + {0x54009 ,LPDDR4_HDT_CTL_3200_1D }, + {0x5400a ,0x0 }, + {0x5400b ,0x2 }, + {0x5400c ,0x0 }, + {0x5400d , (LPDDR4_CATRAIN_3200_1d <<8 ) }, + {0x5400e ,0x0 }, + {0x5400f ,0x0 }, + {0x54010 ,0x0 }, + {0x54011 ,0x0 }, + {0x54012 ,0x310 }, + {0x54013 ,0x0 }, + {0x54014 ,0x0 }, + {0x54015 ,0x0 }, + {0x54016 ,0x0 }, + {0x54017 ,0x0 }, + {0x54018 ,0x0 }, + + {0x54019 ,0x2dd4 }, +#ifdef WR_POST_EXT_3200 + {0x5401a , (((LPDDR4_RON ) <<3 ) |0x3 ) }, +#else + {0x5401a , (((LPDDR4_RON ) <<3 ) |0x1 ) }, +#endif + {0x5401b , ((LPDDR4_VREF_VALUE_CA <<8 ) | + (LPDDR4_RTT_CA_BANK0 <<4 ) |LPDDR4_RTT_DQ ) }, + {0x5401c , ((LPDDR4_VREF_VALUE_DQ_RANK0 <<8 ) |0x08 ) }, + {0x5401d ,0x0 }, + {0x5401e ,LPDDR4_MR22_RANK0 }, + {0x5401f ,0x2dd4 }, +#ifdef WR_POST_EXT_3200 + {0x54020 , (((LPDDR4_RON ) <<3 ) |0x3 ) }, +#else + {0x54020 , (((LPDDR4_RON ) <<3 ) |0x1 ) }, +#endif + {0x54021 , ((LPDDR4_VREF_VALUE_CA <<8 ) | + (LPDDR4_RTT_CA_BANK1 <<4 ) |LPDDR4_RTT_DQ ) }, + {0x54022 , ((LPDDR4_VREF_VALUE_DQ_RANK1 <<8 ) |0x08 ) }, + {0x54023 ,0x0 }, + {0x54024 ,LPDDR4_MR22_RANK1 }, + + {0x54025 ,0x0 }, + {0x54026 ,0x0 }, + {0x54027 ,0x0 }, + {0x54028 ,0x0 }, + {0x54029 ,0x0 }, + {0x5402a ,0x0 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x3 }, + {0x5402d ,0x0 }, + {0x5402e ,0x0 }, + {0x5402f ,0x0 }, + {0x54030 ,0x0 }, + {0x54031 ,0x0 }, + {0x54032 ,0xd400 }, +/* MR3/MR2 */ +#ifdef WR_POST_EXT_3200 + {0x54033 , ((((LPDDR4_RON ) <<3 ) |0x3 ) <<8 ) |0x2d /*0x312d*/ }, +#else + {0x54033 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x2d /*0x312d*/ }, +#endif +/* MR11/MR4 */ + {0x54034 , (((LPDDR4_RTT_CA_BANK0 <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, +/* self:0x284d//MR13/MR12 */ + {0x54035 , (0x0800 |LPDDR4_VREF_VALUE_CA )/*0x084d*/ }, +/* MR16/MR14*/ + {0x54036 ,LPDDR4_VREF_VALUE_DQ_RANK0 /*0x4d*/ }, + {0x54037 , (LPDDR4_MR22_RANK0 <<8 )/*0x500*/ }, +/* MR1 */ + {0x54038 ,0xd400 }, +/* MR3/MR2 */ +#ifdef WR_POST_EXT_3200 + {0x54039 , ((((LPDDR4_RON ) <<3 ) |0x3 ) <<8 ) |0x2d /*0x312d*/ }, +#else + {0x54039 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x2d /*0x312d*/ }, +#endif +/* MR11/MR4 */ + {0x5403a , (((LPDDR4_RTT_CA_BANK1 <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, +/* self:0x284d//MR13/MR12 */ + {0x5403b , (0x0800 |LPDDR4_VREF_VALUE_CA )/*0x084d*/ }, +/* MR16/MR14 */ + {0x5403c ,LPDDR4_VREF_VALUE_DQ_RANK1 /*0x4d*/ }, + {0x5403d , (LPDDR4_MR22_RANK1 <<8 )/*0x500*/ }, +/* { 0x5403d, 0x500 } */ + {0x5403d , (LPDDR4_MR22_RANK1 <<8 )/*0x500*/ }, + {0x5403e ,0x0 }, + {0x5403f ,0x0 }, + {0x54040 ,0x0 }, + {0x54041 ,0x0 }, + {0x54042 ,0x0 }, + {0x54043 ,0x0 }, + {0x54044 ,0x0 }, + {0xd0000 ,0x1 }, +}; + +/* P1 message block paremeter for training firmware */ +struct dram_cfg_param lpddr4_fsp1_cfg[] = { + {0xd0000 ,0x0 }, + {0x54000 ,0x0 }, + {0x54001 ,0x0 }, + {0x54002 ,0x101 }, + {0x54003 ,0x190 }, + {0x54004 ,0x2 }, +/* PHY Ron/Rtt */ + {0x54005 , ((LPDDR4_PHY_RON <<8 ) |LPDDR4_PHY_RTT )/*0x2828*/ }, + {0x54006 ,LPDDR4_PHY_VREF_VALUE }, + {0x54007 ,0x0 }, + {0x54008 ,LPDDR4_TRAIN_SEQ_400 }, + {0x54009 ,LPDDR4_HDT_CTL_400_1D }, + {0x5400a ,0x0 }, + {0x5400b ,0x2 }, + {0x5400c ,0x0 }, + {0x5400d , (LPDDR4_CATRAIN_400 <<8 ) }, + {0x5400e ,0x0 }, + {0x5400f ,0x0 }, + {0x54010 ,0x0 }, + {0x54011 ,0x0 }, + {0x54012 ,0x310 }, + {0x54013 ,0x0 }, + {0x54014 ,0x0 }, + {0x54015 ,0x0 }, + {0x54016 ,0x0 }, + {0x54017 ,0x0 }, + {0x54018 ,0x0 }, + {0x54019 ,0x84 }, +/* MR4/MR3 */ + {0x5401a , (((LPDDR4_RON ) <<3 ) |0x1 )/*0x31*/ }, +/* MR12/MR11 */ + {0x5401b , ((LPDDR4_VREF_VALUE_CA <<8 ) | (LPDDR4_RTT_CA <<4 ) | +LPDDR4_RTT_DQ )/*0x4d46*/ }, +/* self:0x4d28//MR14/MR13 */ + {0x5401c , ((LPDDR4_VREF_VALUE_DQ_RANK0 <<8 ) |0x08 )/*0x4d08*/ }, + {0x5401d ,0x0 }, + {0x5401e ,LPDDR4_MR22_RANK0 /*0x5*/ }, + {0x5401f ,0x84 }, + {0x54020 , (((LPDDR4_RON ) <<3 ) |0x1 )/*0x31*/ },/* MR4/MR3 */ + {0x54021 , ((LPDDR4_VREF_VALUE_CA <<8 ) | (LPDDR4_RTT_CA <<4 ) | +LPDDR4_RTT_DQ )/*0x4d46*/ },/* MR12/MR11 */ +/* self:0x4d28//MR14/MR13 */ + {0x54022 , ((LPDDR4_VREF_VALUE_DQ_RANK1 <<8 ) |0x08 )/*0x4d08*/ }, + {0x54023 ,0x0 }, + {0x54024 ,LPDDR4_MR22_RANK1 }, + {0x54025 ,0x0 }, + {0x54026 ,0x0 }, + {0x54027 ,0x0 }, + {0x54028 ,0x0 }, + {0x54029 ,0x0 }, + {0x5402a ,0x0 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x3 }, + {0x5402d ,0x0 }, + {0x5402e ,0x0 }, + {0x5402f ,0x0 }, + {0x54030 ,0x0 }, + {0x54031 ,0x0 }, + {0x54032 ,0x8400 }, + {0x54033 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x00 }, + {0x54034 , (((LPDDR4_RTT_CA <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, + {0x54035 , (0x0800 |LPDDR4_VREF_VALUE_CA ) }, + {0x54036 ,LPDDR4_VREF_VALUE_DQ_RANK0 }, + {0x54037 , (LPDDR4_MR22_RANK0 <<8 ) }, + {0x54038 ,0x8400 }, + {0x54039 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x00 }, + {0x5403a , (((LPDDR4_RTT_CA <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, + {0x5403b , (0x0800 |LPDDR4_VREF_VALUE_CA ) }, + {0x5403c ,LPDDR4_VREF_VALUE_DQ_RANK1 }, + {0x5403d , (LPDDR4_MR22_RANK1 <<8 ) }, + {0x5403e ,0x0 }, + {0x5403f ,0x0 }, + {0x54040 ,0x0 }, + {0x54041 ,0x0 }, + {0x54042 ,0x0 }, + {0x54043 ,0x0 }, + {0x54044 ,0x0 }, + {0xd0000 ,0x1 }, +}; + +/* P2 message block paremeter for training firmware */ +struct dram_cfg_param lpddr4_fsp2_cfg[] = { + {0xd0000 ,0x0 }, + {0x54000 ,0x0 }, + {0x54001 ,0x0 }, + {0x54002 ,0x102 }, + {0x54003 ,0x64 }, + {0x54004 ,0x2 }, + {0x54005 , ((LPDDR4_PHY_RON <<8 ) |LPDDR4_PHY_RTT ) }, + {0x54006 ,LPDDR4_PHY_VREF_VALUE }, + {0x54007 ,0x0 }, + {0x54008 ,LPDDR4_TRAIN_SEQ_100 }, + {0x54009 ,LPDDR4_HDT_CTL_100_1D }, + {0x5400a ,0x0 }, + {0x5400b ,0x2 }, + {0x5400c ,0x0 }, + {0x5400d , (LPDDR4_CATRAIN_100 <<8 ) }, + {0x5400e ,0x0 }, + {0x5400f ,0x0 }, + {0x54010 ,0x0 }, + {0x54011 ,0x0 }, + {0x54012 ,0x310 }, + {0x54013 ,0x0 }, + {0x54014 ,0x0 }, + {0x54015 ,0x0 }, + {0x54016 ,0x0 }, + {0x54017 ,0x0 }, + {0x54018 ,0x0 }, + {0x54019 ,0x84 }, + {0x5401a , (((LPDDR4_RON ) <<3 ) |0x1 ) }, + {0x5401b , ((LPDDR4_VREF_VALUE_CA <<8 ) | (LPDDR4_RTT_CA <<4 ) | +LPDDR4_RTT_DQ ) }, + {0x5401c , ((LPDDR4_VREF_VALUE_DQ_RANK0 <<8 ) |0x08 ) }, + {0x5401d ,0x0 }, + {0x5401e ,LPDDR4_MR22_RANK0 }, + {0x5401f ,0x84 }, + {0x54020 , (((LPDDR4_RON ) <<3 ) |0x1 ) }, + {0x54021 , ((LPDDR4_VREF_VALUE_CA <<8 ) | (LPDDR4_RTT_CA <<4 ) | +LPDDR4_RTT_DQ ) }, + {0x54022 , ((LPDDR4_VREF_VALUE_DQ_RANK1 <<8 ) |0x08 ) }, + {0x54023 ,0x0 }, + {0x54024 ,LPDDR4_MR22_RANK1 }, + {0x54025 ,0x0 }, + {0x54026 ,0x0 }, + {0x54027 ,0x0 }, + {0x54028 ,0x0 }, + {0x54029 ,0x0 }, + {0x5402a ,0x0 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x3 }, + {0x5402d ,0x0 }, + {0x5402e ,0x0 }, + {0x5402f ,0x0 }, + {0x54030 ,0x0 }, + {0x54031 ,0x0 }, + {0x54032 ,0x8400 }, + {0x54033 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x00 }, + {0x54034 , (((LPDDR4_RTT_CA <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, + {0x54035 , (0x0800 |LPDDR4_VREF_VALUE_CA ) }, + {0x54036 ,LPDDR4_VREF_VALUE_DQ_RANK0 }, + {0x54037 , (LPDDR4_MR22_RANK0 <<8 ) }, + {0x54038 ,0x8400 }, + {0x54039 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x00 }, + {0x5403a , (((LPDDR4_RTT_CA <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, + {0x5403b , (0x0800 |LPDDR4_VREF_VALUE_CA ) }, + {0x5403c ,LPDDR4_VREF_VALUE_DQ_RANK1 }, + {0x5403d , (LPDDR4_MR22_RANK1 <<8 ) }, + {0x5403e ,0x0 }, + {0x5403f ,0x0 }, + {0x54040 ,0x0 }, + {0x54041 ,0x0 }, + {0x54042 ,0x0 }, + {0x54043 ,0x0 }, + {0x54044 ,0x0 }, + {0xd0000 ,0x1 }, +}; + +/* P0 2D message block paremeter for training firmware */ +struct dram_cfg_param lpddr4_fsp0_2d_cfg[] = { + {0xd0000 ,0x0 }, + {0x54000 ,0x0 }, + {0x54001 ,0x0 }, + {0x54002 ,0x0 }, + {0x54003 ,0xc80 }, + {0x54004 ,0x2 }, + {0x54005 , ((LPDDR4_PHY_RON <<8 ) |LPDDR4_PHY_RTT ) }, + {0x54006 ,LPDDR4_PHY_VREF_VALUE }, + {0x54007 ,0x0 }, + {0x54008 ,0x61 }, + {0x54009 ,LPDDR4_HDT_CTL_2D }, + {0x5400a ,0x0 }, + {0x5400b ,0x2 }, + {0x5400c ,0x0 }, + {0x5400d , (LPDDR4_CATRAIN_3200_2d <<8 ) }, + {0x5400e ,0x0 }, + {0x5400f , (LPDDR4_2D_SHARE <<8 ) |0x00 }, + {0x54010 ,LPDDR4_2D_WEIGHT }, + {0x54011 ,0x0 }, + {0x54012 ,0x310 }, + {0x54013 ,0x0 }, + {0x54014 ,0x0 }, + {0x54015 ,0x0 }, + {0x54016 ,0x0 }, + {0x54017 ,0x0 }, + {0x54018 ,0x0 }, + {0x54019 ,0x2dd4 }, +#ifdef WR_POST_EXT_3200 + {0x5401a , (((LPDDR4_RON ) <<3 ) |0x3 ) }, +#else + {0x5401a , (((LPDDR4_RON ) <<3 ) |0x1 ) }, +#endif + {0x5401b , ((LPDDR4_VREF_VALUE_CA <<8 ) | + (LPDDR4_RTT_CA_BANK0 <<4 ) |LPDDR4_RTT_DQ ) }, + {0x5401c , ((LPDDR4_VREF_VALUE_DQ_RANK0 <<8 ) |0x08 ) }, + {0x5401d ,0x0 }, + {0x5401e ,LPDDR4_MR22_RANK0 }, + {0x5401f ,0x2dd4 }, +#ifdef WR_POST_EXT_3200 + {0x54020 , (((LPDDR4_RON ) <<3 ) |0x3 ) }, +#else + {0x54020 , (((LPDDR4_RON ) <<3 ) |0x1 ) }, +#endif + {0x54021 , ((LPDDR4_VREF_VALUE_CA <<8 ) | + (LPDDR4_RTT_CA_BANK1 <<4 ) |LPDDR4_RTT_DQ ) }, + {0x54022 , ((LPDDR4_VREF_VALUE_DQ_RANK1 <<8 ) |0x08 ) }, + {0x54023 ,0x0 }, + {0x54024 ,LPDDR4_MR22_RANK1 }, + {0x54025 ,0x0 }, + {0x54026 ,0x0 }, + {0x54027 ,0x0 }, + {0x54028 ,0x0 }, + {0x54029 ,0x0 }, + {0x5402a ,0x0 }, + {0x5402b ,0x1000 }, + {0x5402c ,0x3 }, + {0x5402d ,0x0 }, + {0x5402e ,0x0 }, + {0x5402f ,0x0 }, + {0x54030 ,0x0 }, + {0x54031 ,0x0 }, + + {0x54032 ,0xd400 }, +#ifdef WR_POST_EXT_3200 + {0x54033 , ((((LPDDR4_RON ) <<3 ) |0x3 ) <<8 ) |0x2d }, +#else + {0x54033 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x2d }, +#endif + {0x54034 , (((LPDDR4_RTT_CA_BANK0 <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, + {0x54035 , (0x0800 |LPDDR4_VREF_VALUE_CA ) }, + {0x54036 ,LPDDR4_VREF_VALUE_DQ_RANK0 }, + {0x54037 , (LPDDR4_MR22_RANK0 <<8 ) }, + {0x54038 ,0xd400 }, +#ifdef WR_POST_EXT_3200 + {0x54039 , ((((LPDDR4_RON ) <<3 ) |0x3 ) <<8 ) |0x2d }, +#else + {0x54039 , ((((LPDDR4_RON ) <<3 ) |0x1 ) <<8 ) |0x2d }, +#endif + {0x5403a , (((LPDDR4_RTT_CA_BANK1 <<4 ) |LPDDR4_RTT_DQ ) <<8 ) }, + {0x5403b , (0x0800 |LPDDR4_VREF_VALUE_CA ) }, + {0x5403c ,LPDDR4_VREF_VALUE_DQ_RANK1 }, + {0x5403d , (LPDDR4_MR22_RANK1 <<8 ) }, + {0x5403e ,0x0 }, + {0x5403f ,0x0 }, + {0x54040 ,0x0 }, + {0x54041 ,0x0 }, + {0x54042 ,0x0 }, + {0x54043 ,0x0 }, + {0x54044 ,0x0 }, + {0xd0000 ,0x1 }, +}; + +/* DRAM PHY init engine image */ +struct dram_cfg_param lpddr4_phy_pie[] = { + {0xd0000 ,0x0 }, + {0x90000 ,0x10 }, + {0x90001 ,0x400 }, + {0x90002 ,0x10e }, + {0x90003 ,0x0 }, + {0x90004 ,0x0 }, + {0x90005 ,0x8 }, + {0x90029 ,0xb }, + {0x9002a ,0x480 }, + {0x9002b ,0x109 }, + {0x9002c ,0x8 }, + {0x9002d ,0x448 }, + {0x9002e ,0x139 }, + {0x9002f ,0x8 }, + {0x90030 ,0x478 }, + {0x90031 ,0x109 }, + {0x90032 ,0x0 }, + {0x90033 ,0xe8 }, + {0x90034 ,0x109 }, + {0x90035 ,0x2 }, + {0x90036 ,0x10 }, + {0x90037 ,0x139 }, + {0x90038 ,0xf }, + {0x90039 ,0x7c0 }, + {0x9003a ,0x139 }, + {0x9003b ,0x44 }, + {0x9003c ,0x630 }, + {0x9003d ,0x159 }, + {0x9003e ,0x14f }, + {0x9003f ,0x630 }, + {0x90040 ,0x159 }, + {0x90041 ,0x47 }, + {0x90042 ,0x630 }, + {0x90043 ,0x149 }, + {0x90044 ,0x4f }, + {0x90045 ,0x630 }, + {0x90046 ,0x179 }, + {0x90047 ,0x8 }, + {0x90048 ,0xe0 }, + {0x90049 ,0x109 }, + {0x9004a ,0x0 }, + {0x9004b ,0x7c8 }, + {0x9004c ,0x109 }, + {0x9004d ,0x0 }, + {0x9004e ,0x1 }, + {0x9004f ,0x8 }, + {0x90050 ,0x0 }, + {0x90051 ,0x45a }, + {0x90052 ,0x9 }, + {0x90053 ,0x0 }, + {0x90054 ,0x448 }, + {0x90055 ,0x109 }, + {0x90056 ,0x40 }, + {0x90057 ,0x630 }, + {0x90058 ,0x179 }, + {0x90059 ,0x1 }, + {0x9005a ,0x618 }, + {0x9005b ,0x109 }, + {0x9005c ,0x40c0 }, + {0x9005d ,0x630 }, + {0x9005e ,0x149 }, + {0x9005f ,0x8 }, + {0x90060 ,0x4 }, + {0x90061 ,0x48 }, + {0x90062 ,0x4040 }, + {0x90063 ,0x630 }, + {0x90064 ,0x149 }, + {0x90065 ,0x0 }, + {0x90066 ,0x4 }, + {0x90067 ,0x48 }, + {0x90068 ,0x40 }, + {0x90069 ,0x630 }, + {0x9006a ,0x149 }, + {0x9006b ,0x10 }, + {0x9006c ,0x4 }, + {0x9006d ,0x18 }, + {0x9006e ,0x0 }, + {0x9006f ,0x4 }, + {0x90070 ,0x78 }, + {0x90071 ,0x549 }, + {0x90072 ,0x630 }, + {0x90073 ,0x159 }, + {0x90074 ,0xd49 }, + {0x90075 ,0x630 }, + {0x90076 ,0x159 }, + {0x90077 ,0x94a }, + {0x90078 ,0x630 }, + {0x90079 ,0x159 }, + {0x9007a ,0x441 }, + {0x9007b ,0x630 }, + {0x9007c ,0x149 }, + {0x9007d ,0x42 }, + {0x9007e ,0x630 }, + {0x9007f ,0x149 }, + {0x90080 ,0x1 }, + {0x90081 ,0x630 }, + {0x90082 ,0x149 }, + {0x90083 ,0x0 }, + {0x90084 ,0xe0 }, + {0x90085 ,0x109 }, + {0x90086 ,0xa }, + {0x90087 ,0x10 }, + {0x90088 ,0x109 }, + {0x90089 ,0x9 }, + {0x9008a ,0x3c0 }, + {0x9008b ,0x149 }, + {0x9008c ,0x9 }, + {0x9008d ,0x3c0 }, + {0x9008e ,0x159 }, + {0x9008f ,0x18 }, + {0x90090 ,0x10 }, + {0x90091 ,0x109 }, + {0x90092 ,0x0 }, + {0x90093 ,0x3c0 }, + {0x90094 ,0x109 }, + {0x90095 ,0x18 }, + {0x90096 ,0x4 }, + {0x90097 ,0x48 }, + {0x90098 ,0x18 }, + {0x90099 ,0x4 }, + {0x9009a ,0x58 }, + {0x9009b ,0xa }, + {0x9009c ,0x10 }, + {0x9009d ,0x109 }, + {0x9009e ,0x2 }, + {0x9009f ,0x10 }, + {0x900a0 ,0x109 }, + {0x900a1 ,0x5 }, + {0x900a2 ,0x7c0 }, + {0x900a3 ,0x109 }, + {0x900a4 ,0x10 }, + {0x900a5 ,0x10 }, + {0x900a6 ,0x109 }, + {0x40000 ,0x811 }, + {0x40020 ,0x880 }, + {0x40040 ,0x0 }, + {0x40060 ,0x0 }, + {0x40001 ,0x4008 }, + {0x40021 ,0x83 }, + {0x40041 ,0x4f }, + {0x40061 ,0x0 }, + {0x40002 ,0x4040 }, + {0x40022 ,0x83 }, + {0x40042 ,0x51 }, + {0x40062 ,0x0 }, + {0x40003 ,0x811 }, + {0x40023 ,0x880 }, + {0x40043 ,0x0 }, + {0x40063 ,0x0 }, + {0x40004 ,0x720 }, + {0x40024 ,0xf }, + {0x40044 ,0x1740 }, + {0x40064 ,0x0 }, + {0x40005 ,0x16 }, + {0x40025 ,0x83 }, + {0x40045 ,0x4b }, + {0x40065 ,0x0 }, + {0x40006 ,0x716 }, + {0x40026 ,0xf }, + {0x40046 ,0x2001 }, + {0x40066 ,0x0 }, + {0x40007 ,0x716 }, + {0x40027 ,0xf }, + {0x40047 ,0x2800 }, + {0x40067 ,0x0 }, + {0x40008 ,0x716 }, + {0x40028 ,0xf }, + {0x40048 ,0xf00 }, + {0x40068 ,0x0 }, + {0x40009 ,0x720 }, + {0x40029 ,0xf }, + {0x40049 ,0x1400 }, + {0x40069 ,0x0 }, + {0x4000a ,0xe08 }, + {0x4002a ,0xc15 }, + {0x4004a ,0x0 }, + {0x4006a ,0x0 }, + {0x4000b ,0x623 }, + {0x4002b ,0x15 }, + {0x4004b ,0x0 }, + {0x4006b ,0x0 }, + {0x4000c ,0x4028 }, + {0x4002c ,0x80 }, + {0x4004c ,0x0 }, + {0x4006c ,0x0 }, + {0x4000d ,0xe08 }, + {0x4002d ,0xc1a }, + {0x4004d ,0x0 }, + {0x4006d ,0x0 }, + {0x4000e ,0x623 }, + {0x4002e ,0x1a }, + {0x4004e ,0x0 }, + {0x4006e ,0x0 }, + {0x4000f ,0x4040 }, + {0x4002f ,0x80 }, + {0x4004f ,0x0 }, + {0x4006f ,0x0 }, + {0x40010 ,0x2604 }, + {0x40030 ,0x15 }, + {0x40050 ,0x0 }, + {0x40070 ,0x0 }, + {0x40011 ,0x708 }, + {0x40031 ,0x5 }, + {0x40051 ,0x0 }, + {0x40071 ,0x2002 }, + {0x40012 ,0x8 }, + {0x40032 ,0x80 }, + {0x40052 ,0x0 }, + {0x40072 ,0x0 }, + {0x40013 ,0x2604 }, + {0x40033 ,0x1a }, + {0x40053 ,0x0 }, + {0x40073 ,0x0 }, + {0x40014 ,0x708 }, + {0x40034 ,0xa }, + {0x40054 ,0x0 }, + {0x40074 ,0x2002 }, + {0x40015 ,0x4040 }, + {0x40035 ,0x80 }, + {0x40055 ,0x0 }, + {0x40075 ,0x0 }, + {0x40016 ,0x60a }, + {0x40036 ,0x15 }, + {0x40056 ,0x1200 }, + {0x40076 ,0x0 }, + {0x40017 ,0x61a }, + {0x40037 ,0x15 }, + {0x40057 ,0x1300 }, + {0x40077 ,0x0 }, + {0x40018 ,0x60a }, + {0x40038 ,0x1a }, + {0x40058 ,0x1200 }, + {0x40078 ,0x0 }, + {0x40019 ,0x642 }, + {0x40039 ,0x1a }, + {0x40059 ,0x1300 }, + {0x40079 ,0x0 }, + {0x4001a ,0x4808 }, + {0x4003a ,0x880 }, + {0x4005a ,0x0 }, + {0x4007a ,0x0 }, + {0x900a7 ,0x0 }, + {0x900a8 ,0x790 }, + {0x900a9 ,0x11a }, + {0x900aa ,0x8 }, + {0x900ab ,0x7aa }, + {0x900ac ,0x2a }, + {0x900ad ,0x10 }, + {0x900ae ,0x7b2 }, + {0x900af ,0x2a }, + {0x900b0 ,0x0 }, + {0x900b1 ,0x7c8 }, + {0x900b2 ,0x109 }, + {0x900b3 ,0x10 }, + {0x900b4 ,0x2a8 }, + {0x900b5 ,0x129 }, + {0x900b6 ,0x8 }, + {0x900b7 ,0x370 }, + {0x900b8 ,0x129 }, + {0x900b9 ,0xa }, + {0x900ba ,0x3c8 }, + {0x900bb ,0x1a9 }, + {0x900bc ,0xc }, + {0x900bd ,0x408 }, + {0x900be ,0x199 }, + {0x900bf ,0x14 }, + {0x900c0 ,0x790 }, + {0x900c1 ,0x11a }, + {0x900c2 ,0x8 }, + {0x900c3 ,0x4 }, + {0x900c4 ,0x18 }, + {0x900c5 ,0xe }, + {0x900c6 ,0x408 }, + {0x900c7 ,0x199 }, + {0x900c8 ,0x8 }, + {0x900c9 ,0x8568 }, + {0x900ca ,0x108 }, + {0x900cb ,0x18 }, + {0x900cc ,0x790 }, + {0x900cd ,0x16a }, + {0x900ce ,0x8 }, + {0x900cf ,0x1d8 }, + {0x900d0 ,0x169 }, + {0x900d1 ,0x10 }, + {0x900d2 ,0x8558 }, + {0x900d3 ,0x168 }, + {0x900d4 ,0x70 }, + {0x900d5 ,0x788 }, + {0x900d6 ,0x16a }, + {0x900d7 ,0x1ff8 }, + {0x900d8 ,0x85a8 }, + {0x900d9 ,0x1e8 }, + {0x900da ,0x50 }, + {0x900db ,0x798 }, + {0x900dc ,0x16a }, + {0x900dd ,0x60 }, + {0x900de ,0x7a0 }, + {0x900df ,0x16a }, + {0x900e0 ,0x8 }, + {0x900e1 ,0x8310 }, + {0x900e2 ,0x168 }, + {0x900e3 ,0x8 }, + {0x900e4 ,0xa310 }, + {0x900e5 ,0x168 }, + {0x900e6 ,0xa }, + {0x900e7 ,0x408 }, + {0x900e8 ,0x169 }, + {0x900e9 ,0x6e }, + {0x900ea ,0x0 }, + {0x900eb ,0x68 }, + {0x900ec ,0x0 }, + {0x900ed ,0x408 }, + {0x900ee ,0x169 }, + {0x900ef ,0x0 }, + {0x900f0 ,0x8310 }, + {0x900f1 ,0x168 }, + {0x900f2 ,0x0 }, + {0x900f3 ,0xa310 }, + {0x900f4 ,0x168 }, + {0x900f5 ,0x1ff8 }, + {0x900f6 ,0x85a8 }, + {0x900f7 ,0x1e8 }, + {0x900f8 ,0x68 }, + {0x900f9 ,0x798 }, + {0x900fa ,0x16a }, + {0x900fb ,0x78 }, + {0x900fc ,0x7a0 }, + {0x900fd ,0x16a }, + {0x900fe ,0x68 }, + {0x900ff ,0x790 }, + {0x90100 ,0x16a }, + {0x90101 ,0x8 }, + {0x90102 ,0x8b10 }, + {0x90103 ,0x168 }, + {0x90104 ,0x8 }, + {0x90105 ,0xab10 }, + {0x90106 ,0x168 }, + {0x90107 ,0xa }, + {0x90108 ,0x408 }, + {0x90109 ,0x169 }, + {0x9010a ,0x58 }, + {0x9010b ,0x0 }, + {0x9010c ,0x68 }, + {0x9010d ,0x0 }, + {0x9010e ,0x408 }, + {0x9010f ,0x169 }, + {0x90110 ,0x0 }, + {0x90111 ,0x8b10 }, + {0x90112 ,0x168 }, + {0x90113 ,0x0 }, + {0x90114 ,0xab10 }, + {0x90115 ,0x168 }, + {0x90116 ,0x0 }, + {0x90117 ,0x1d8 }, + {0x90118 ,0x169 }, + {0x90119 ,0x80 }, + {0x9011a ,0x790 }, + {0x9011b ,0x16a }, + {0x9011c ,0x18 }, + {0x9011d ,0x7aa }, + {0x9011e ,0x6a }, + {0x9011f ,0xa }, + {0x90120 ,0x0 }, + {0x90121 ,0x1e9 }, + {0x90122 ,0x8 }, + {0x90123 ,0x8080 }, + {0x90124 ,0x108 }, + {0x90125 ,0xf }, + {0x90126 ,0x408 }, + {0x90127 ,0x169 }, + {0x90128 ,0xc }, + {0x90129 ,0x0 }, + {0x9012a ,0x68 }, + {0x9012b ,0x9 }, + {0x9012c ,0x0 }, + {0x9012d ,0x1a9 }, + {0x9012e ,0x0 }, + {0x9012f ,0x408 }, + {0x90130 ,0x169 }, + {0x90131 ,0x0 }, + {0x90132 ,0x8080 }, + {0x90133 ,0x108 }, + {0x90134 ,0x8 }, + {0x90135 ,0x7aa }, + {0x90136 ,0x6a }, + {0x90137 ,0x0 }, + {0x90138 ,0x8568 }, + {0x90139 ,0x108 }, + {0x9013a ,0xb7 }, + {0x9013b ,0x790 }, + {0x9013c ,0x16a }, + {0x9013d ,0x1f }, + {0x9013e ,0x0 }, + {0x9013f ,0x68 }, + {0x90140 ,0x8 }, + {0x90141 ,0x8558 }, + {0x90142 ,0x168 }, + {0x90143 ,0xf }, + {0x90144 ,0x408 }, + {0x90145 ,0x169 }, + {0x90146 ,0xc }, + {0x90147 ,0x0 }, + {0x90148 ,0x68 }, + {0x90149 ,0x0 }, + {0x9014a ,0x408 }, + {0x9014b ,0x169 }, + {0x9014c ,0x0 }, + {0x9014d ,0x8558 }, + {0x9014e ,0x168 }, + {0x9014f ,0x8 }, + {0x90150 ,0x3c8 }, + {0x90151 ,0x1a9 }, + {0x90152 ,0x3 }, + {0x90153 ,0x370 }, + {0x90154 ,0x129 }, + {0x90155 ,0x20 }, + {0x90156 ,0x2aa }, + {0x90157 ,0x9 }, + {0x90158 ,0x0 }, + {0x90159 ,0x400 }, + {0x9015a ,0x10e }, + {0x9015b ,0x8 }, + {0x9015c ,0xe8 }, + {0x9015d ,0x109 }, + {0x9015e ,0x0 }, + {0x9015f ,0x8140 }, + {0x90160 ,0x10c }, + {0x90161 ,0x10 }, + {0x90162 ,0x8138 }, + {0x90163 ,0x10c }, + {0x90164 ,0x8 }, + {0x90165 ,0x7c8 }, + {0x90166 ,0x101 }, + {0x90167 ,0x8 }, + {0x90168 ,0x0 }, + {0x90169 ,0x8 }, + {0x9016a ,0x8 }, + {0x9016b ,0x448 }, + {0x9016c ,0x109 }, + {0x9016d ,0xf }, + {0x9016e ,0x7c0 }, + {0x9016f ,0x109 }, + {0x90170 ,0x0 }, + {0x90171 ,0xe8 }, + {0x90172 ,0x109 }, + {0x90173 ,0x47 }, + {0x90174 ,0x630 }, + {0x90175 ,0x109 }, + {0x90176 ,0x8 }, + {0x90177 ,0x618 }, + {0x90178 ,0x109 }, + {0x90179 ,0x8 }, + {0x9017a ,0xe0 }, + {0x9017b ,0x109 }, + {0x9017c ,0x0 }, + {0x9017d ,0x7c8 }, + {0x9017e ,0x109 }, + {0x9017f ,0x8 }, + {0x90180 ,0x8140 }, + {0x90181 ,0x10c }, + {0x90182 ,0x0 }, + {0x90183 ,0x1 }, + {0x90184 ,0x8 }, + {0x90185 ,0x8 }, + {0x90186 ,0x4 }, + {0x90187 ,0x8 }, + {0x90188 ,0x8 }, + {0x90189 ,0x7c8 }, + {0x9018a ,0x101 }, + {0x90006 ,0x0 }, + {0x90007 ,0x0 }, + {0x90008 ,0x8 }, + {0x90009 ,0x0 }, + {0x9000a ,0x0 }, + {0x9000b ,0x0 }, + {0xd00e7 ,0x400 }, + {0x90017 ,0x0 }, + {0x9001f ,0x2a }, + {0x90026 ,0x6a }, + {0x400d0 ,0x0 }, + {0x400d1 ,0x101 }, + {0x400d2 ,0x105 }, + {0x400d3 ,0x107 }, + {0x400d4 ,0x10f }, + {0x400d5 ,0x202 }, + {0x400d6 ,0x20a }, + {0x400d7 ,0x20b }, + {0x2003a ,0x2 }, + {0x2000b ,0x64 }, + {0x2000c ,0xc8 }, + {0x2000d ,0x7d0 }, + {0x2000e ,0x2c }, + {0x12000b ,0xc }, + {0x12000c ,0x19 }, + {0x12000d ,0xfa }, + {0x12000e ,0x10 }, + {0x22000b ,0x3 }, + {0x22000c ,0x6 }, + {0x22000d ,0x3e }, + {0x22000e ,0x10 }, + {0x9000c ,0x0 }, + {0x9000d ,0x173 }, + {0x9000e ,0x60 }, + {0x9000f ,0x6110 }, + {0x90010 ,0x2152 }, + {0x90011 ,0xdfbd }, + {0x90012 ,0x60 }, + {0x90013 ,0x6152 }, + {0x20010 ,0x5a }, + {0x20011 ,0x3 }, + {0x40080 ,0xe0 }, + {0x40081 ,0x12 }, + {0x40082 ,0xe0 }, + {0x40083 ,0x12 }, + {0x40084 ,0xe0 }, + {0x40085 ,0x12 }, + {0x140080 ,0xe0 }, + {0x140081 ,0x12 }, + {0x140082 ,0xe0 }, + {0x140083 ,0x12 }, + {0x140084 ,0xe0 }, + {0x140085 ,0x12 }, + {0x240080 ,0xe0 }, + {0x240081 ,0x12 }, + {0x240082 ,0xe0 }, + {0x240083 ,0x12 }, + {0x240084 ,0xe0 }, + {0x240085 ,0x12 }, + {0x400fd ,0xf }, + {0x10011 ,0x1 }, + {0x10012 ,0x1 }, + {0x10013 ,0x180 }, + {0x10018 ,0x1 }, + {0x10002 ,0x6209 }, + {0x100b2 ,0x1 }, + {0x101b4 ,0x1 }, + {0x102b4 ,0x1 }, + {0x103b4 ,0x1 }, + {0x104b4 ,0x1 }, + {0x105b4 ,0x1 }, + {0x106b4 ,0x1 }, + {0x107b4 ,0x1 }, + {0x108b4 ,0x1 }, + {0x11011 ,0x1 }, + {0x11012 ,0x1 }, + {0x11013 ,0x180 }, + {0x11018 ,0x1 }, + {0x11002 ,0x6209 }, + {0x110b2 ,0x1 }, + {0x111b4 ,0x1 }, + {0x112b4 ,0x1 }, + {0x113b4 ,0x1 }, + {0x114b4 ,0x1 }, + {0x115b4 ,0x1 }, + {0x116b4 ,0x1 }, + {0x117b4 ,0x1 }, + {0x118b4 ,0x1 }, + {0x12011 ,0x1 }, + {0x12012 ,0x1 }, + {0x12013 ,0x180 }, + {0x12018 ,0x1 }, + {0x12002 ,0x6209 }, + {0x120b2 ,0x1 }, + {0x121b4 ,0x1 }, + {0x122b4 ,0x1 }, + {0x123b4 ,0x1 }, + {0x124b4 ,0x1 }, + {0x125b4 ,0x1 }, + {0x126b4 ,0x1 }, + {0x127b4 ,0x1 }, + {0x128b4 ,0x1 }, + {0x13011 ,0x1 }, + {0x13012 ,0x1 }, + {0x13013 ,0x180 }, + {0x13018 ,0x1 }, + {0x13002 ,0x6209 }, + {0x130b2 ,0x1 }, + {0x131b4 ,0x1 }, + {0x132b4 ,0x1 }, + {0x133b4 ,0x1 }, + {0x134b4 ,0x1 }, + {0x135b4 ,0x1 }, + {0x136b4 ,0x1 }, + {0x137b4 ,0x1 }, + {0x138b4 ,0x1 }, + {0x2003a ,0x2 }, + {0xc0080 ,0x2 }, + {0xd0000 ,0x1 }, +}; + +struct dram_fsp_msg lpddr4_dram_fsp_msg[] = { + { +/* P0 3200mts 1D */ + .drate =3200 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = lpddr4_fsp0_cfg, + .fsp_cfg_num =ARRAY_SIZE (lpddr4_fsp0_cfg), + }, + { +/* P1 400mts 1D */ + .drate =400 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = lpddr4_fsp1_cfg, + .fsp_cfg_num =ARRAY_SIZE (lpddr4_fsp1_cfg), + }, + { +/* P1 100mts 1D */ + .drate =100 , + .fw_type =FW_1D_IMAGE , + .fsp_cfg = lpddr4_fsp2_cfg, + .fsp_cfg_num =ARRAY_SIZE (lpddr4_fsp2_cfg), + }, + { +/* P0 3200mts 2D */ + .drate =3200 , + .fw_type =FW_2D_IMAGE , + .fsp_cfg = lpddr4_fsp0_2d_cfg, + .fsp_cfg_num =ARRAY_SIZE (lpddr4_fsp0_2d_cfg), + }, +}; + +/* lpddr4 timing config params on EVK board */ +struct dram_timing_info dram_timing = { + .ddrc_cfg = lpddr4_ddrc_cfg, + .ddrc_cfg_num =ARRAY_SIZE (lpddr4_ddrc_cfg), + .ddrphy_cfg = lpddr4_ddrphy_cfg, + .ddrphy_cfg_num =ARRAY_SIZE (lpddr4_ddrphy_cfg), + .fsp_msg = lpddr4_dram_fsp_msg, + .fsp_msg_num =ARRAY_SIZE (lpddr4_dram_fsp_msg), + .ddrphy_pie = lpddr4_phy_pie, + .ddrphy_pie_num =ARRAY_SIZE (lpddr4_phy_pie), + .fsp_table = {3200 ,400 ,100 , }, +};
board/purism/librem5/lpddr4_timing_b0.c new file +1191 -0
1,191 lines not on this page · raw message
Signature · 1 line
2.25.1
PATCH 11/13 board: librem5: add Librem5 MAINTAINERS file
In reply to Angus AinslieInitial commit of the Librem5 MAINTAINERS file
--- board/purism/librem5/MAINTAINERS | 7 +++++++ 1 file changed, 7 insertions(+) create mode 100644 board/purism/librem5/MAINTAINERS
board/purism/librem5/MAINTAINERS new file +7 -0
@@ -0,0 +1,7 @@ +PURISM LIBREM5 PHONE +M: Angus Ainslie <[email protected]> +R: [email protected] +S: Supported +F: board/purism/librem5/ +F: configs/librem5_defconfig +F: include/configs/librem5.h
Signature · 1 line
2.25.1
PATCH 12/13 board: librem5: add Librem5 build files
In reply to Angus AinslieInitial commit of the Librem5 Makefile and Kconfig
--- board/purism/librem5/Kconfig | 15 +++++++++++++++ board/purism/librem5/Makefile | 13 +++++++++++++ 2 files changed, 28 insertions(+) create mode 100644 board/purism/librem5/Kconfig create mode 100644 board/purism/librem5/Makefile
board/purism/librem5/Kconfig new file +15 -0
@@ -0,0 +1,15 @@ +if TARGET_LIBREM5 + +config SYS_BOARD + default "librem5" + +config SYS_VENDOR + default "purism" + +config SYS_CONFIG_NAME + default "librem5" + +config IMX_CONFIG + default "board/purism/librem5/imximage-8mq-lpddr4.cfg" + +endif
board/purism/librem5/Makefile new file +13 -0
@@ -0,0 +1,13 @@ +# +# Copyright 2017 NXP +# Copyright 2019 Purism +# +# SPDX-License-Identifier: GPL-2.0+ +# + +obj-y += librem5.o + +ifdef CONFIG_SPL_BUILD +obj-y += spl.o +obj-$(CONFIG_IMX8M_LPDDR4) += lpddr4_timing.o lpddr4_timing_b0.o +endif
Signature · 1 line
2.25.1
PATCH 13/13 doc: librem5: add Librem5 documentation
In reply to Angus AinslieInitial commit of the Librem5 documentation
--- doc/board/purism/librem5/librem5.rst | 60 ++++++++++++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 doc/board/purism/librem5/librem5.rst
doc/board/purism/librem5/librem5.rst new file +60 -0
@@ -0,0 +1,60 @@ +.. SPDX-License-Identifier: GPL-2.0+ + +Librem5 +========== + +U-Boot for the Purism Librem5 phone + +Quick Start +----------- + +- Build the ARM Trusted firmware binary +- Get ddr and hdmi firmware +- Build U-Boot + +Get and Build the ARM Trusted firmware +-------------------------------------- + +Note: srctree is U-Boot source directory +Get ATF from: https://source.puri.sm/Librem5/arm-trusted-firmware +branch: librem5 + +.. code-block:: bash + + $ make PLAT=imx8mq bl31 + $ cp build/imx8mq/release/bl31.bin $(builddir) + +Get the ddr and hdmi firmware +----------------------------- + +.. code-block:: bash + + $ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.10.bin + $ chmod +x firmware-imx-8.10.bin + $ ./firmware-imx-8.10.bin + $ cp firmware-imx-8.10/firmware/hdmi/cadence/signed_hdmi_imx8m.bin $(builddir) + $ cp firmware-imx-8.10/firmware/ddr/synopsys/lpddr4*.bin $(builddir) + +Build U-Boot +------------ + +.. code-block:: bash + + $ export CROSS_COMPILE=aarch64-linux-gnu + $ make librem5_defconfig + $ make flash.bin + +Burn the flash.bin +------------------ + +Use uuu to burn flash.bin. Power on the phone while holding vol+ to get it +into uuu mode. + +.. code-block:: bash + + $ git clone https://source.puri.sm/Librem5/librem5-devkit-tools.git + $ cd librem5-devkit-tools + $ cp $(builddir)/flash.bin files/ + $ uuu uuu_scripts/u-boot_flash_librem5.lst + +Reboot the phone.
Signature · 1 line
2.25.1
Re: [PATCH 13/13] doc: librem5: add Librem5 documentation
Quoted 7 lines · Angus Ainslie
Initial commit of the Librem5 documentation
Signed-off-by Angus Ainslie <[email protected]>--- doc/board/purism/librem5/librem5.rst | 60 ++++++++++++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 doc/board/purism/librem5/librem5.rst
If you don't also update the index files, this won't be included, or will give an error? Also, I suspect there's some problems about headings and so forth, please make sure "make htmldocs" is happy.
Signature · 1 line
Tom
Quoted 10 lines · Angus Ainslie
I sent this patchset as a single monolithic patch and did not see any comment on it.
https://lists.denx.de/pipermail/u-boot/2022-January/471087.html
Here it is as a set of patches instead.
This is all of the code required to boot the Librem5 Phone.
It can boot the phone in uuu mode or directly from the eMMC
Yes, sorry, we're a little behind on imx-related patches right now. In general yes, splitting this up a bit helps, but it's too split now. I'll reply with some specific questions / comments, but the way it was before is better really.
Signature · 1 line
Tom
Hi Toni
Quoted 9 lines · Tom Rini
Quoted 7 lines · Angus Ainslie
I sent this patchset as a single monolithic patch and did not see any comment on it.
https://lists.denx.de/pipermail/u-boot/2022-January/471087.html
Here it is as a set of patches instead.
Quoted 8 lines
Quoted 3 lines
This is all of the code required to boot the Librem5 Phone.
It can boot the phone in uuu mode or directly from the eMMC
Yes, sorry, we're a little behind on imx-related patches right now. In general yes, splitting this up a bit helps, but it's too split now. I'll reply with some specific questions / comments, but the way it was before is better really.
Thanks for the review and I'll start making changes for v2.
About how it should be split up. Should all of the "board/purism/librem5" and config files be in one patch with the devicetree and documentation in separate patches ?
Thanks
Angus
Quoted 2 lines · Angus Ainslie
Hi Toni
Sorry Tom, somehow concatenated your 2 names.
Quoted 5 lines · Angus Ainslie
Quoted 2 lines · Angus Ainslie
Hi Toni
Sorry Tom, somehow concatenated your 2 names.
No worries.
Signature · 1 line
Tom
Quoted 21 lines · Angus Ainslie
Hi Toni
Quoted 9 lines · Tom Rini
Quoted 7 lines · Angus Ainslie
I sent this patchset as a single monolithic patch and did not see any comment on it.
https://lists.denx.de/pipermail/u-boot/2022-January/471087.html
Here it is as a set of patches instead.
Quoted 8 lines
Quoted 3 lines
This is all of the code required to boot the Librem5 Phone.
It can boot the phone in uuu mode or directly from the eMMC
Yes, sorry, we're a little behind on imx-related patches right now. In general yes, splitting this up a bit helps, but it's too split now. I'll reply with some specific questions / comments, but the way it was before is better really.
Quoted 5 lines
Thanks for the review and I'll start making changes for v2.
About how it should be split up. Should all of the "board/purism/librem5" and config files be in one patch with the devicetree and documentation in separate patches ?
Since you've already split out driver/etc changes to other patches, one patch with board/ and include/configs/ and configs/ and dts files is fine.
Signature · 1 line
Tom