Skip to contentSkip to conversation

regulator: rpi-panel: Support official Raspberry Pi 7 inches touchscreen

PATCH Superseded Detlev Casanova 2 participants 11 messages Jan 20, 2022 Voltage and current regulator framework

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore
#0 lore raw

cover regulator: rpi-panel: Support official Raspberry Pi 7 inches touchscreen

This patchset provides different fixes to the rpi-panel-attiny-regulator driver.

This is a preparation patchset for supporting the official Raspberry Pi 7 inches touchscreen.

It has been tested with a Raspberry Pi 4 B and the official Raspberry Pi 7 inches touchscreen.

Dave Stevenson (9):
regulator: rpi-panel: Register with a unique backlight name
regulator: rpi-panel: Handle I2C errors/timing to the Atmel
regulator: rpi-panel: Serialise operations.
regulator: rpi-panel: Ensure the backlight is off during probe.
regulator: rpi-panel: Convert to drive lines directly
regulator: rpi-panel: Add GPIO control for panel and touch resets
regulator: rpi-panel: Remove get_brightness hook regulator/rpi-panel-attiny: Don't read the LCD power status regulator/rpi-panel-attiny: Use two transactions for I2C read

 .../regulator/rpi-panel-attiny-regulator.c    | 285 +++++++++++++++---
 1 file changed, 236 insertions(+), 49 deletions(-)
Signature · 1 line
2.34.1
#1 lore raw

PATCH 1/9 regulator: rpi-panel: Register with a unique backlight name

From: Dave Stevenson <[email protected]>

There's no reason why 2 Raspberry Pi DSI displays can't be attached to a Pi Compute Module, so the backlight names need to be unique.

Use the parent dev_name. It's not as readable, but is unique.

---
 drivers/regulator/rpi-panel-attiny-regulator.c | 3 +--
 1 file changed, 1 insertion(+), 2 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +1 -2
index ee46bfbf5eee..370b9ae363dd 100644
@@ -181,8 +181,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 
 	props.type = BACKLIGHT_RAW;
 	props.max_brightness = 0xff;
-	bl = devm_backlight_device_register(&i2c->dev,
-					    "7inch-touchscreen-panel-bl",
+	bl = devm_backlight_device_register(&i2c->dev, dev_name(&i2c->dev),
 					    &i2c->dev, regmap, &attiny_bl,
 					    &props);
 	if (IS_ERR(bl))
Signature · 1 line
2.34.1
#2 lore raw

PATCH 2/9 regulator: rpi-panel: Handle I2C errors/timing to the Atmel

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The Atmel is doing some things in the I2C ISR, during which period it will not respond to further commands. This is particularly true of the POWERON command.

Increase delays appropriately, and retry should I2C errors be reported.

---
 .../regulator/rpi-panel-attiny-regulator.c    | 56 +++++++++++++++----
 1 file changed, 46 insertions(+), 10 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +46 -10
index 370b9ae363dd..00fb69efcfa2 100644
@@ -37,11 +37,24 @@ static const struct regmap_config attiny_regmap_config = {
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
 	unsigned int data;
+	int ret, i;
 
 	regmap_write(rdev->regmap, REG_POWERON, 1);
+	msleep(80);
+
 	/* Wait for nPWRDWN to go low to indicate poweron is done. */
-	regmap_read_poll_timeout(rdev->regmap, REG_PORTB, data,
-					data & BIT(0), 10, 1000000);
+	for (i = 0; i < 20; i++) {
+		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		if (!ret) {
+			if (data & BIT(0))
+				break;
+		}
+		usleep_range(10000, 12000);
+	}
+	usleep_range(10000, 12000);
+
+	if (ret)
+		pr_err("%s: regmap_read_poll_timeout failed %d\n", __func__, ret);
 
 	/* Default to the same orientation as the closed source
 	 * firmware used for the panel.  Runtime rotation
@@ -57,23 +70,34 @@ static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 {
 	regmap_write(rdev->regmap, REG_PWM, 0);
 	regmap_write(rdev->regmap, REG_POWERON, 0);
-	udelay(1);
+	msleep(30);
 	return 0;
 }
 
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
 	unsigned int data;
-	int ret;
+	int ret, i;
 
-	ret = regmap_read(rdev->regmap, REG_POWERON, &data);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(rdev->regmap, REG_POWERON, &data);
+		if (!ret)
+			break;
+		usleep_range(10000, 12000);
+	}
 	if (ret < 0)
 		return ret;
 
 	if (!(data & BIT(0)))
 		return 0;
 
-	ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		if (!ret)
+			break;
+		usleep_range(10000, 12000);
+	}
+
 	if (ret < 0)
 		return ret;
 
@@ -103,20 +127,32 @@ static int attiny_update_status(struct backlight_device *bl)
 {
 	struct regmap *regmap = bl_get_data(bl);
 	int brightness = bl->props.brightness;
+	int ret, i;
 
 	if (bl->props.power != FB_BLANK_UNBLANK ||
 	    bl->props.fb_blank != FB_BLANK_UNBLANK)
 		brightness = 0;
 
-	return regmap_write(regmap, REG_PWM, brightness);
+	for (i = 0; i < 10; i++) {
+		ret = regmap_write(regmap, REG_PWM, brightness);
+		if (!ret)
+			break;
+	}
+
+	return ret;
 }
 
 static int attiny_get_brightness(struct backlight_device *bl)
 {
 	struct regmap *regmap = bl_get_data(bl);
-	int ret, brightness;
+	int ret, brightness, i;
+
+	for (i = 0; i < 10; i++) {
+		ret = regmap_read(regmap, REG_PWM, &brightness);
+		if (!ret)
+			break;
+	}
 
-	ret = regmap_read(regmap, REG_PWM, &brightness);
 	if (ret)
 		return ret;
 
@@ -166,7 +202,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	}
 
 	regmap_write(regmap, REG_POWERON, 0);
-	mdelay(1);
+	msleep(30);
 
 	config.dev = &i2c->dev;
 	config.regmap = regmap;
Signature · 1 line
2.34.1
#3 lore raw

PATCH 3/9 regulator: rpi-panel: Serialise operations.

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The driver was using the regmap lock to serialise the individual accesses, but we really need to protect the timings of enabling the regulators, including any communication with the Atmel.

Use a mutex within the driver to control overall accesses to the Atmel, instead of the regmap lock.

---
 .../regulator/rpi-panel-attiny-regulator.c    | 91 ++++++++++++++++---
 1 file changed, 80 insertions(+), 11 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +80 -11
index 00fb69efcfa2..a4af7adad2b5 100644
@@ -27,18 +27,28 @@
 #define REG_POWERON	0x85
 #define REG_PWM		0x86
 
+struct attiny_lcd {
+	/* lock to serialise overall accesses to the Atmel */
+	struct mutex	lock;
+	struct regmap	*regmap;
+};
+
 static const struct regmap_config attiny_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
+	.disable_locking = 1,
 	.max_register = REG_PWM,
 	.cache_type = REGCACHE_NONE,
 };
 
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
+	struct mutex *lock = rdev_get_drvdata(rdev);
 	unsigned int data;
 	int ret, i;
 
+	mutex_lock(lock);
+
 	regmap_write(rdev->regmap, REG_POWERON, 1);
 	msleep(80);
 
@@ -63,33 +73,49 @@ static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 	 */
 	regmap_write(rdev->regmap, REG_PORTA, BIT(2));
 
+	mutex_unlock(lock);
+
 	return 0;
 }
 
 static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 {
+	struct mutex *lock = rdev_get_drvdata(rdev);
+
+	mutex_lock(lock);
+
 	regmap_write(rdev->regmap, REG_PWM, 0);
 	regmap_write(rdev->regmap, REG_POWERON, 0);
 	msleep(30);
+
+	mutex_unlock(lock);
+
 	return 0;
 }
 
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
+	struct mutex *lock = rdev_get_drvdata(rdev);
 	unsigned int data;
 	int ret, i;
 
+	mutex_lock(lock);
+
 	for (i = 0; i < 10; i++) {
 		ret = regmap_read(rdev->regmap, REG_POWERON, &data);
 		if (!ret)
 			break;
 		usleep_range(10000, 12000);
 	}
-	if (ret < 0)
+	if (ret < 0) {
+		mutex_unlock(lock);
 		return ret;
+	}
 
-	if (!(data & BIT(0)))
+	if (!(data & BIT(0))) {
+		mutex_unlock(lock);
 		return 0;
+	}
 
 	for (i = 0; i < 10; i++) {
 		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
@@ -98,6 +124,8 @@ static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 		usleep_range(10000, 12000);
 	}
 
+	mutex_unlock(lock);
+
 	if (ret < 0)
 		return ret;
 
@@ -125,10 +153,13 @@ static const struct regulator_desc attiny_regulator = {
 
 static int attiny_update_status(struct backlight_device *bl)
 {
-	struct regmap *regmap = bl_get_data(bl);
+	struct attiny_lcd *state = bl_get_data(bl);
+	struct regmap *regmap = state->regmap;
 	int brightness = bl->props.brightness;
 	int ret, i;
 
+	mutex_lock(&state->lock);
+
 	if (bl->props.power != FB_BLANK_UNBLANK ||
 	    bl->props.fb_blank != FB_BLANK_UNBLANK)
 		brightness = 0;
@@ -139,20 +170,27 @@ static int attiny_update_status(struct backlight_device *bl)
 			break;
 	}
 
+	mutex_unlock(&state->lock);
+
 	return ret;
 }
 
 static int attiny_get_brightness(struct backlight_device *bl)
 {
-	struct regmap *regmap = bl_get_data(bl);
+	struct attiny_lcd *state = bl_get_data(bl);
+	struct regmap *regmap = state->regmap;
 	int ret, brightness, i;
 
+	mutex_lock(&state->lock);
+
 	for (i = 0; i < 10; i++) {
 		ret = regmap_read(regmap, REG_PWM, &brightness);
 		if (!ret)
 			break;
 	}
 
+	mutex_unlock(&state->lock);
+
 	if (ret)
 		return ret;
 
@@ -174,22 +212,30 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	struct regulator_config config = { };
 	struct backlight_device *bl;
 	struct regulator_dev *rdev;
+	struct attiny_lcd *state;
 	struct regmap *regmap;
 	unsigned int data;
 	int ret;
 
+	state = devm_kzalloc(&i2c->dev, sizeof(*state), GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	mutex_init(&state->lock);
+	i2c_set_clientdata(i2c, state);
+
 	regmap = devm_regmap_init_i2c(i2c, &attiny_regmap_config);
 	if (IS_ERR(regmap)) {
 		ret = PTR_ERR(regmap);
 		dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
 			ret);
-		return ret;
+		goto error;
 	}
 
 	ret = regmap_read(regmap, REG_ID, &data);
 	if (ret < 0) {
 		dev_err(&i2c->dev, "Failed to read REG_ID reg: %d\n", ret);
-		return ret;
+		goto error;
 	}
 
 	switch (data) {
@@ -198,7 +244,8 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 		break;
 	default:
 		dev_err(&i2c->dev, "Unknown Atmel firmware revision: 0x%02x\n", data);
-		return -ENODEV;
+		ret = -ENODEV;
+		goto error;
 	}
 
 	regmap_write(regmap, REG_POWERON, 0);
@@ -208,23 +255,44 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	config.regmap = regmap;
 	config.of_node = i2c->dev.of_node;
 	config.init_data = &attiny_regulator_default;
+	config.driver_data = &state->lock;
 
 	rdev = devm_regulator_register(&i2c->dev, &attiny_regulator, &config);
 	if (IS_ERR(rdev)) {
 		dev_err(&i2c->dev, "Failed to register ATTINY regulator\n");
-		return PTR_ERR(rdev);
+		ret = PTR_ERR(rdev);
+		goto error;
 	}
 
 	props.type = BACKLIGHT_RAW;
 	props.max_brightness = 0xff;
+
+	state->regmap = regmap;
+
 	bl = devm_backlight_device_register(&i2c->dev, dev_name(&i2c->dev),
-					    &i2c->dev, regmap, &attiny_bl,
+					    &i2c->dev, state, &attiny_bl,
 					    &props);
-	if (IS_ERR(bl))
-		return PTR_ERR(bl);
+	if (IS_ERR(bl)) {
+		ret = PTR_ERR(bl);
+		goto error;
+	}
 
 	bl->props.brightness = 0xff;
 
+	return 0;
+
+error:
+	mutex_destroy(&state->lock);
+
+	return ret;
+}
+
+static int attiny_i2c_remove(struct i2c_client *client)
+{
+	struct attiny_lcd *state = i2c_get_clientdata(client);
+
+	mutex_destroy(&state->lock);
+
 	return 0;
 }
 
@@ -240,6 +308,7 @@ static struct i2c_driver attiny_regulator_driver = {
 		.of_match_table = of_match_ptr(attiny_dt_ids),
 	},
 	.probe = attiny_i2c_probe,
+	.remove	= attiny_i2c_remove,
 };
 
 module_i2c_driver(attiny_regulator_driver);
Signature · 1 line
2.34.1
#4 lore raw

PATCH 4/9 regulator: rpi-panel: Ensure the backlight is off during probe.

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The initial state of the Atmel is not defined, so ensure the backlight PWM is set to 0 by default.

---
 drivers/regulator/rpi-panel-attiny-regulator.c | 1 +
 1 file changed, 1 insertion(+)
drivers/regulator/rpi-panel-attiny-regulator.c +1 -0
index a4af7adad2b5..b3629a1e0e50 100644
@@ -250,6 +250,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 
 	regmap_write(regmap, REG_POWERON, 0);
 	msleep(30);
+	regmap_write(regmap, REG_PWM, 0);
 
 	config.dev = &i2c->dev;
 	config.regmap = regmap;
Signature · 1 line
2.34.1
#5 lore raw

PATCH 5/9 regulator: rpi-panel: Convert to drive lines directly

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The Atmel was doing a load of automatic sequencing of control lines, however it was combining the touch controller's reset with the bridge/panel control.

Change to control the control signals directly rather than through the automatic POWERON control.

---
 .../regulator/rpi-panel-attiny-regulator.c    | 111 ++++++++++--------
 1 file changed, 60 insertions(+), 51 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +60 -51
index b3629a1e0e50..995915ca4a9b 100644
@@ -21,11 +21,28 @@
 /* I2C registers of the Atmel microcontroller. */
 #define REG_ID		0x80
 #define REG_PORTA	0x81
-#define REG_PORTA_HF	BIT(2)
-#define REG_PORTA_VF	BIT(3)
 #define REG_PORTB	0x82
+#define REG_PORTC	0x83
 #define REG_POWERON	0x85
 #define REG_PWM		0x86
+#define REG_ADDR_L	0x8c
+#define REG_ADDR_H	0x8d
+#define REG_WRITE_DATA_H	0x90
+#define REG_WRITE_DATA_L	0x91
+
+#define PA_LCD_DITHB		BIT(0)
+#define PA_LCD_MODE		BIT(1)
+#define PA_LCD_LR		BIT(2)
+#define PA_LCD_UD		BIT(3)
+
+#define PB_BRIDGE_PWRDNX_N	BIT(0)
+#define PB_LCD_VCC_N		BIT(1)
+#define PB_LCD_MAIN		BIT(7)
+
+#define PC_LED_EN		BIT(0)
+#define PC_RST_TP_N		BIT(1)
+#define PC_RST_LCD_N		BIT(2)
+#define PC_RST_BRIDGE_N		BIT(3)
 
 struct attiny_lcd {
 	/* lock to serialise overall accesses to the Atmel */
@@ -37,99 +54,91 @@ static const struct regmap_config attiny_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
 	.disable_locking = 1,
-	.max_register = REG_PWM,
+	.max_register = REG_WRITE_DATA_L,
 	.cache_type = REGCACHE_NONE,
 };
 
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
-	struct mutex *lock = rdev_get_drvdata(rdev);
-	unsigned int data;
-	int ret, i;
-
-	mutex_lock(lock);
-
-	regmap_write(rdev->regmap, REG_POWERON, 1);
-	msleep(80);
+	struct attiny_lcd *state = rdev_get_drvdata(rdev);
 
-	/* Wait for nPWRDWN to go low to indicate poweron is done. */
-	for (i = 0; i < 20; i++) {
-		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
-		if (!ret) {
-			if (data & BIT(0))
-				break;
-		}
-		usleep_range(10000, 12000);
-	}
-	usleep_range(10000, 12000);
+	mutex_lock(&state->lock);
 
-	if (ret)
-		pr_err("%s: regmap_read_poll_timeout failed %d\n", __func__, ret);
+	/* Ensure bridge, and tp stay in reset */
+	regmap_write(rdev->regmap, REG_PORTC, 0);
+	usleep_range(5000, 10000);
 
 	/* Default to the same orientation as the closed source
 	 * firmware used for the panel.  Runtime rotation
 	 * configuration will be supported using VC4's plane
 	 * orientation bits.
 	 */
-	regmap_write(rdev->regmap, REG_PORTA, BIT(2));
+	regmap_write(rdev->regmap, REG_PORTA, PA_LCD_LR);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTB, PB_LCD_MAIN);
+	usleep_range(5000, 10000);
+	/* Bring controllers out of reset */
+	regmap_write(rdev->regmap, REG_PORTC,
+		     PC_LED_EN | PC_RST_BRIDGE_N | PC_RST_LCD_N | PC_RST_TP_N);
+
+	msleep(80);
+
+	regmap_write(rdev->regmap, REG_ADDR_H, 0x04);
+	usleep_range(5000, 8000);
+	regmap_write(rdev->regmap, REG_ADDR_L, 0x7c);
+	usleep_range(5000, 8000);
+	regmap_write(rdev->regmap, REG_WRITE_DATA_H, 0x00);
+	usleep_range(5000, 8000);
+	regmap_write(rdev->regmap, REG_WRITE_DATA_L, 0x00);
+
+	msleep(100);
 
-	mutex_unlock(lock);
+	mutex_unlock(&state->lock);
 
 	return 0;
 }
 
 static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 {
-	struct mutex *lock = rdev_get_drvdata(rdev);
+	struct attiny_lcd *state = rdev_get_drvdata(rdev);
 
-	mutex_lock(lock);
+	mutex_lock(&state->lock);
 
 	regmap_write(rdev->regmap, REG_PWM, 0);
-	regmap_write(rdev->regmap, REG_POWERON, 0);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTA, 0);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTB, PB_LCD_VCC_N);
+	usleep_range(5000, 10000);
+	regmap_write(rdev->regmap, REG_PORTC, 0);
 	msleep(30);
 
-	mutex_unlock(lock);
+	mutex_unlock(&state->lock);
 
 	return 0;
 }
 
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
-	struct mutex *lock = rdev_get_drvdata(rdev);
+	struct attiny_lcd *state = rdev_get_drvdata(rdev);
 	unsigned int data;
 	int ret, i;
 
-	mutex_lock(lock);
-
-	for (i = 0; i < 10; i++) {
-		ret = regmap_read(rdev->regmap, REG_POWERON, &data);
-		if (!ret)
-			break;
-		usleep_range(10000, 12000);
-	}
-	if (ret < 0) {
-		mutex_unlock(lock);
-		return ret;
-	}
-
-	if (!(data & BIT(0))) {
-		mutex_unlock(lock);
-		return 0;
-	}
+	mutex_lock(&state->lock);
 
 	for (i = 0; i < 10; i++) {
-		ret = regmap_read(rdev->regmap, REG_PORTB, &data);
+		ret = regmap_read(rdev->regmap, REG_PORTC, &data);
 		if (!ret)
 			break;
 		usleep_range(10000, 12000);
 	}
 
-	mutex_unlock(lock);
+	mutex_unlock(&state->lock);
 
 	if (ret < 0)
 		return ret;
 
-	return data & BIT(0);
+	return data & PC_RST_BRIDGE_N;
 }
 
 static const struct regulator_init_data attiny_regulator_default = {
@@ -256,7 +265,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	config.regmap = regmap;
 	config.of_node = i2c->dev.of_node;
 	config.init_data = &attiny_regulator_default;
-	config.driver_data = &state->lock;
+	config.driver_data = state;
 
 	rdev = devm_regulator_register(&i2c->dev, &attiny_regulator, &config);
 	if (IS_ERR(rdev)) {
Signature · 1 line
2.34.1
#6 lore raw

PATCH 6/9 regulator: rpi-panel: Add GPIO control for panel and touch resets

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

We need independent control of the resets for the panel&bridge, vs the touch controller.

Expose the reset lines that are on the Atmel's port C via the GPIO API so that they can be controlled appropriately.

---
 .../regulator/rpi-panel-attiny-regulator.c    | 115 +++++++++++++++---
 1 file changed, 97 insertions(+), 18 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +97 -18
index 995915ca4a9b..998233f14085 100644
@@ -8,6 +8,7 @@
 #include <linux/backlight.h>
 #include <linux/err.h>
 #include <linux/gpio.h>
+#include <linux/gpio/driver.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
 #include <linux/interrupt.h>
@@ -44,10 +45,30 @@
 #define PC_RST_LCD_N		BIT(2)
 #define PC_RST_BRIDGE_N		BIT(3)
 
+enum gpio_signals {
+	RST_BRIDGE_N,	/* TC358762 bridge reset */
+	RST_TP_N,	/* Touch controller reset */
+	NUM_GPIO
+};
+
+struct gpio_signal_mappings {
+	unsigned int reg;
+	unsigned int mask;
+};
+
+static const struct gpio_signal_mappings mappings[NUM_GPIO] = {
+	[RST_BRIDGE_N] = { REG_PORTC, PC_RST_BRIDGE_N | PC_RST_LCD_N  },
+	[RST_TP_N] = { REG_PORTC, PC_RST_TP_N },
+};
+
 struct attiny_lcd {
 	/* lock to serialise overall accesses to the Atmel */
 	struct mutex	lock;
 	struct regmap	*regmap;
+	bool gpio_states[NUM_GPIO];
+	u8 port_states[3];
+
+	struct gpio_chip gc;
 };
 
 static const struct regmap_config attiny_regmap_config = {
@@ -58,6 +79,17 @@ static const struct regmap_config attiny_regmap_config = {
 	.cache_type = REGCACHE_NONE,
 };
 
+static int attiny_set_port_state(struct attiny_lcd *state, int reg, u8 val)
+{
+	state->port_states[reg - REG_PORTA] = val;
+	return regmap_write(state->regmap, reg, val);
+};
+
+static u8 attiny_get_port_state(struct attiny_lcd *state, int reg)
+{
+	return state->port_states[reg - REG_PORTA];
+};
+
 static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 {
 	struct attiny_lcd *state = rdev_get_drvdata(rdev);
@@ -65,7 +97,7 @@ static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 	mutex_lock(&state->lock);
 
 	/* Ensure bridge, and tp stay in reset */
-	regmap_write(rdev->regmap, REG_PORTC, 0);
+	attiny_set_port_state(state, REG_PORTC, 0);
 	usleep_range(5000, 10000);
 
 	/* Default to the same orientation as the closed source
@@ -73,26 +105,16 @@ static int attiny_lcd_power_enable(struct regulator_dev *rdev)
 	 * configuration will be supported using VC4's plane
 	 * orientation bits.
 	 */
-	regmap_write(rdev->regmap, REG_PORTA, PA_LCD_LR);
+	attiny_set_port_state(state, REG_PORTA, PA_LCD_LR);
 	usleep_range(5000, 10000);
-	regmap_write(rdev->regmap, REG_PORTB, PB_LCD_MAIN);
+	/* Main regulator on, and power to the panel (LCD_VCC_N) */
+	attiny_set_port_state(state, REG_PORTB, PB_LCD_MAIN);
 	usleep_range(5000, 10000);
 	/* Bring controllers out of reset */
-	regmap_write(rdev->regmap, REG_PORTC,
-		     PC_LED_EN | PC_RST_BRIDGE_N | PC_RST_LCD_N | PC_RST_TP_N);
+	attiny_set_port_state(state, REG_PORTC, PC_LED_EN);
 
 	msleep(80);
 
-	regmap_write(rdev->regmap, REG_ADDR_H, 0x04);
-	usleep_range(5000, 8000);
-	regmap_write(rdev->regmap, REG_ADDR_L, 0x7c);
-	usleep_range(5000, 8000);
-	regmap_write(rdev->regmap, REG_WRITE_DATA_H, 0x00);
-	usleep_range(5000, 8000);
-	regmap_write(rdev->regmap, REG_WRITE_DATA_L, 0x00);
-
-	msleep(100);
-
 	mutex_unlock(&state->lock);
 
 	return 0;
@@ -106,11 +128,12 @@ static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 
 	regmap_write(rdev->regmap, REG_PWM, 0);
 	usleep_range(5000, 10000);
-	regmap_write(rdev->regmap, REG_PORTA, 0);
+
+	attiny_set_port_state(state, REG_PORTA, 0);
 	usleep_range(5000, 10000);
-	regmap_write(rdev->regmap, REG_PORTB, PB_LCD_VCC_N);
+	attiny_set_port_state(state, REG_PORTB, PB_LCD_VCC_N);
 	usleep_range(5000, 10000);
-	regmap_write(rdev->regmap, REG_PORTC, 0);
+	attiny_set_port_state(state, REG_PORTC, 0);
 	msleep(30);
 
 	mutex_unlock(&state->lock);
@@ -211,6 +234,45 @@ static const struct backlight_ops attiny_bl = {
 	.get_brightness	= attiny_get_brightness,
 };
 
+static int attiny_gpio_get_direction(struct gpio_chip *gc, unsigned int off)
+{
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static void attiny_gpio_set(struct gpio_chip *gc, unsigned int off, int val)
+{
+	struct attiny_lcd *state = gpiochip_get_data(gc);
+	u8 last_val;
+
+	if (off >= NUM_GPIO)
+		return;
+
+	mutex_lock(&state->lock);
+
+	last_val = attiny_get_port_state(state, mappings[off].reg);
+	if (val)
+		last_val |= mappings[off].mask;
+	else
+		last_val &= ~mappings[off].mask;
+
+	attiny_set_port_state(state, mappings[off].reg, last_val);
+
+	if (off == RST_BRIDGE_N && val) {
+		usleep_range(5000, 8000);
+		regmap_write(state->regmap, REG_ADDR_H, 0x04);
+		usleep_range(5000, 8000);
+		regmap_write(state->regmap, REG_ADDR_L, 0x7c);
+		usleep_range(5000, 8000);
+		regmap_write(state->regmap, REG_WRITE_DATA_H, 0x00);
+		usleep_range(5000, 8000);
+		regmap_write(state->regmap, REG_WRITE_DATA_L, 0x00);
+
+		msleep(100);
+	}
+
+	mutex_unlock(&state->lock);
+}
+
 /*
  * I2C driver interface functions
  */
@@ -289,6 +351,23 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 
 	bl->props.brightness = 0xff;
 
+	state->gc.parent = &i2c->dev;
+	state->gc.label = i2c->name;
+	state->gc.owner = THIS_MODULE;
+	state->gc.of_node = i2c->dev.of_node;
+	state->gc.base = -1;
+	state->gc.ngpio = NUM_GPIO;
+
+	state->gc.set = attiny_gpio_set;
+	state->gc.get_direction = attiny_gpio_get_direction;
+	state->gc.can_sleep = true;
+
+	ret = devm_gpiochip_add_data(&i2c->dev, &state->gc, state);
+	if (ret) {
+		dev_err(&i2c->dev, "Failed to create gpiochip: %d\n", ret);
+		goto error;
+	}
+
 	return 0;
 
 error:
Signature · 1 line
2.34.1
#7 lore raw

Re: [PATCH 6/9] regulator: rpi-panel: Add GPIO control for panel and touch resets

I love your patch! Yet something to improve:

Hi Detlev,

I love your patch! Yet something to improve:

[auto build test ERROR on broonie-regulator/for-next]
[also build test ERROR on linux/master linus/master v5.16 next-20220120] [If your patch is applied to the wrong git tree, kindly drop us a note. And when submitting patch, we suggest to use '--base' as documented in
https://git-scm.com/docs/git-format-patch]

url:    https://github.com/0day-ci/linux/commits/Detlev-Casanova/regulator-rpi-panel-Support-official-Raspberry-Pi-7-inches-touchscreen/20220120-232556
base:   https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next
config: s390-randconfig-r001-20220120 (https://download.01.org/0day-ci/archive/20220121/202201210743.XoBKCVhD-lkp(a)intel.com/config)
compiler: s390-linux-gcc (GCC) 11.2.0

reproduce (this is a W=1 build):
wget https://raw.githubusercontent.com/intel/lkp-tests/master/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# https://github.com/0day-ci/linux/commit/848d1b620ddbd455b87831380d57719aa0e28bb8
git remote add linux-review https://github.com/0day-ci/linux
git fetch --no-tags linux-review Detlev-Casanova/regulator-rpi-panel-Support-official-Raspberry-Pi-7-inches-touchscreen/20220120-232556 git checkout 848d1b620ddbd455b87831380d57719aa0e28bb8
# save the config file to linux build tree
mkdir build_dir
COMPILER_INSTALL_PATH=$HOME/0day COMPILER=gcc-11.2.0 make.cross O=build_dir ARCH=s390 SHELL=/bin/bash drivers/

If you fix the issue, kindly add following tag as appropriate

All errors (new ones prefixed by >>):

drivers/regulator/rpi-panel-attiny-regulator.c: In function 'attiny_i2c_probe':

>> drivers/regulator/rpi-panel-attiny-regulator.c:357:18: error: 'struct gpio_chip' has no member named 'of_node'
     357 |         state->gc.of_node = i2c->dev.of_node;
         |                  ^
   At top level:
   drivers/regulator/rpi-panel-attiny-regulator.c:388:34: warning: 'attiny_dt_ids' defined but not used [-Wunused-const-variable=]
     388 | static const struct of_device_id attiny_dt_ids[] = {
         |                                  ^~~~~~~~~~~~~

vim +357 drivers/regulator/rpi-panel-attiny-regulator.c

275
276 /*
277 * I2C driver interface functions
278 */
279 static int attiny_i2c_probe(struct i2c_client *i2c,
280 const struct i2c_device_id *id)
281 {
282 struct backlight_properties props = { };
283 struct regulator_config config = { };
284 struct backlight_device *bl;
285 struct regulator_dev *rdev;
286 struct attiny_lcd *state;
287 struct regmap *regmap;
288 unsigned int data;
289 int ret;
290
291 state = devm_kzalloc(&i2c->dev, sizeof(*state), GFP_KERNEL);
292 if (!state)
293 return -ENOMEM;
294
295 mutex_init(&state->lock);
296 i2c_set_clientdata(i2c, state);
297
298 regmap = devm_regmap_init_i2c(i2c, &attiny_regmap_config);
299 if (IS_ERR(regmap)) {
300 ret = PTR_ERR(regmap);
301 dev_err(&i2c->dev, "Failed to allocate register map: %d\n",
302 ret);
303 goto error;
304 }
305
306 ret = regmap_read(regmap, REG_ID, &data);
307 if (ret < 0) {
308 dev_err(&i2c->dev, "Failed to read REG_ID reg: %d\n", ret);
309 goto error;
310 }
311
312 switch (data) {
313 case 0xde: /* ver 1 */
314 case 0xc3: /* ver 2 */
315 break;
316 default:
317 dev_err(&i2c->dev, "Unknown Atmel firmware revision: 0x%02x\n", data);
318 ret = -ENODEV;
319 goto error;
320 }
321
322 regmap_write(regmap, REG_POWERON, 0);
323 msleep(30);
324 regmap_write(regmap, REG_PWM, 0);
325
326 config.dev = &i2c->dev;
327 config.regmap = regmap;
328 config.of_node = i2c->dev.of_node;
329 config.init_data = &attiny_regulator_default;
330 config.driver_data = state;
331
332 rdev = devm_regulator_register(&i2c->dev, &attiny_regulator, &config);
333 if (IS_ERR(rdev)) {
334 dev_err(&i2c->dev, "Failed to register ATTINY regulator\n");
335 ret = PTR_ERR(rdev);
336 goto error;
337 }
338
339 props.type = BACKLIGHT_RAW;
340 props.max_brightness = 0xff;
341
342 state->regmap = regmap;
343
344 bl = devm_backlight_device_register(&i2c->dev, dev_name(&i2c->dev),
345 &i2c->dev, state, &attiny_bl,
346 &props);
347 if (IS_ERR(bl)) {
348 ret = PTR_ERR(bl);
349 goto error;
350 }
351
352 bl->props.brightness = 0xff;
353
354 state->gc.parent = &i2c->dev;
355 state->gc.label = i2c->name;
356 state->gc.owner = THIS_MODULE;

 > 357		state->gc.of_node = i2c->dev.of_node;

358 state->gc.base = -1;
359 state->gc.ngpio = NUM_GPIO;
360
361 state->gc.set = attiny_gpio_set;
362 state->gc.get_direction = attiny_gpio_get_direction;
363 state->gc.can_sleep = true;
364
365 ret = devm_gpiochip_add_data(&i2c->dev, &state->gc, state);
366 if (ret) {
367 dev_err(&i2c->dev, "Failed to create gpiochip: %d\n", ret);
368 goto error;
369 }
370
371 return 0;
372
373 error:
374 mutex_destroy(&state->lock);
375
376 return ret;
377 }
378

---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/kbuild-all(a)lists.01.org

#8 lore raw

PATCH 7/9 regulator: rpi-panel: Remove get_brightness hook

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The driver was implementing a get_brightness function that tried to read back the PWM setting of the display to report as the current brightness.
The controller on the display does not support that, therefore we end up reporting a brightness of 0, and that confuses systemd's backlight service.

Remove the hook so that the framework returns the current brightness automatically.

---
 .../regulator/rpi-panel-attiny-regulator.c    | 23 -------------------
 1 file changed, 23 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +0 -23
index 998233f14085..8090b9a485b5 100644
@@ -207,31 +207,8 @@ static int attiny_update_status(struct backlight_device *bl)
 	return ret;
 }
 
-static int attiny_get_brightness(struct backlight_device *bl)
-{
-	struct attiny_lcd *state = bl_get_data(bl);
-	struct regmap *regmap = state->regmap;
-	int ret, brightness, i;
-
-	mutex_lock(&state->lock);
-
-	for (i = 0; i < 10; i++) {
-		ret = regmap_read(regmap, REG_PWM, &brightness);
-		if (!ret)
-			break;
-	}
-
-	mutex_unlock(&state->lock);
-
-	if (ret)
-		return ret;
-
-	return brightness;
-}
-
 static const struct backlight_ops attiny_bl = {
 	.update_status	= attiny_update_status,
-	.get_brightness	= attiny_get_brightness,
 };
 
 static int attiny_gpio_get_direction(struct gpio_chip *gc, unsigned int off)
Signature · 1 line
2.34.1
#9 lore raw

PATCH 8/9 regulator/rpi-panel-attiny: Don't read the LCD power status

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The I2C to the Atmel is very fussy, and locks up easily on Pi0-3 particularly on reads.

The LCD power status is controlled solely by this driver, so rather than reading it back from the Atmel, use the cached status last set.

---
 drivers/regulator/rpi-panel-attiny-regulator.c | 18 +-----------------
 1 file changed, 1 insertion(+), 17 deletions(-)
drivers/regulator/rpi-panel-attiny-regulator.c +1 -17
index 8090b9a485b5..8b80c0de1022 100644
@@ -144,24 +144,8 @@ static int attiny_lcd_power_disable(struct regulator_dev *rdev)
 static int attiny_lcd_power_is_enabled(struct regulator_dev *rdev)
 {
 	struct attiny_lcd *state = rdev_get_drvdata(rdev);
-	unsigned int data;
-	int ret, i;
-
-	mutex_lock(&state->lock);
-
-	for (i = 0; i < 10; i++) {
-		ret = regmap_read(rdev->regmap, REG_PORTC, &data);
-		if (!ret)
-			break;
-		usleep_range(10000, 12000);
-	}
-
-	mutex_unlock(&state->lock);
-
-	if (ret < 0)
-		return ret;
 
-	return data & PC_RST_BRIDGE_N;
+	return state->port_states[REG_PORTC - REG_PORTA] & PC_RST_BRIDGE_N;
 }
 
 static const struct regulator_init_data attiny_regulator_default = {
Signature · 1 line
2.34.1
#10 lore raw

PATCH 9/9 regulator/rpi-panel-attiny: Use two transactions for I2C read

In reply to Detlev Casanova

From: Dave Stevenson <[email protected]>

The I2C to the Atmel is very fussy, and locks up easily on Pi0-3 particularly on reads.
If running at 100kHz on Pi3, reading the ID register generally locks up the Atmel, but splitting the register select write and read into two transactions is reliable.

---
 .../regulator/rpi-panel-attiny-regulator.c    | 35 ++++++++++++++++++-
 1 file changed, 34 insertions(+), 1 deletion(-)
drivers/regulator/rpi-panel-attiny-regulator.c +34 -1
index 8b80c0de1022..e3decc419814 100644
@@ -234,6 +234,39 @@ static void attiny_gpio_set(struct gpio_chip *gc, unsigned int off, int val)
 	mutex_unlock(&state->lock);
 }
 
+static int attiny_i2c_read(struct i2c_client *client, u8 reg, unsigned int *buf)
+{
+	struct i2c_msg msgs[1];
+	u8 addr_buf[1] = { reg };
+	u8 data_buf[1] = { 0, };
+	int ret;
+
+	/* Write register address */
+	msgs[0].addr = client->addr;
+	msgs[0].flags = 0;
+	msgs[0].len = ARRAY_SIZE(addr_buf);
+	msgs[0].buf = addr_buf;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret != ARRAY_SIZE(msgs))
+		return -EIO;
+
+	usleep_range(5000, 10000);
+
+	/* Read data from register */
+	msgs[0].addr = client->addr;
+	msgs[0].flags = I2C_M_RD;
+	msgs[0].len = 1;
+	msgs[0].buf = data_buf;
+
+	ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs));
+	if (ret != ARRAY_SIZE(msgs))
+		return -EIO;
+
+	*buf = data_buf[0];
+	return 0;
+}
+
 /*
  * I2C driver interface functions
  */
@@ -264,7 +297,7 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 		goto error;
 	}
 
-	ret = regmap_read(regmap, REG_ID, &data);
+	ret = attiny_i2c_read(i2c, REG_ID, &data);
 	if (ret < 0) {
 		dev_err(&i2c->dev, "Failed to read REG_ID reg: %d\n", ret);
 		goto error;
Signature · 1 line
2.34.1