drivers/perf: CPU PMU driver for Apple M1
Subsystems (5)
v4 cover drivers/perf: CPU PMU driver for Apple M1
The M1 SoC embeds a per-CPU PMU that has a very different programming interface compared to the architected PMUv3 that is normally present on standard implementations.
This small series adds a driver for this HW by leveraging the arm_pmu infrastructure, resulting in a rather simple driver.
Of course, we know next to nothing about the actual events this PMU counts, aside from CPU cycles and instructions. Everything else is undocumented (though as Dougall pointed out, someone could extract the relevant information from a macOS install if they wanted -- I don't). I'm looking at allowing the perf userspace tool to load the event descriptions at runtime, which would probably help.
* From v3 [3]:
- DT binding fixes
- Typo fixes (and probably more added)
- Rebased on 5.17-rc1
* From v2 [2]:
- Reworked the way the FIQ virtual affinity is exposed (now coming from the DT instead of being internal to the irqchip driver)
- Dropped the locking from the PMU driver after Mark's review
- Required the exclude_guest flag to be set, as the PMU doesn't seem to be able to count guest events, at least by default
- Dropped the counter-stop on interrupt and instead stop the whole PMU on interrupt
- Dropped the kernel taint, as I couldn't find a good way to do that on first use
- Collected RBs from Hector
* From v1 [1]:
- Added a few comments clarifying the event mapping to counters
- Spelling fixes
- Collected Acks from Rob
[1] https://lore.kernel.org/r/[email protected]
[2] https://lore.kernel.org/r/[email protected]
[3] https://lore.kernel.org/r/[email protected]
Marc Zyngier (10):
dt-bindings: arm-pmu: Document Apple PMU compatible strings
dt-bindings: apple,aic: Add CPU PMU per-cpu pseudo-interrupts
dt-bindings: apple,aic: Add affinity description for per-cpu
pseudo-interrupts
irqchip/apple-aic: Parse FIQ affinities from device-tree irqchip/apple-aic: Wire PMU interrupts
arm64: dts: apple: Add t8103 PMU interrupt affinities
arm64: dts: apple: Add t8303 PMU nodes irqchip/apple-aic: Move PMU-specific registers to their own include
file
drivers/perf: arm_pmu: Handle 47 bit counters drivers/perf: Add Apple icestorm/firestorm CPU PMU driver
.../devicetree/bindings/arm/pmu.yaml | 2 + .../interrupt-controller/apple,aic.yaml | 29 + arch/arm64/boot/dts/apple/t8103.dtsi | 24 + arch/arm64/include/asm/apple_m1_pmu.h | 64 ++ drivers/irqchip/irq-apple-aic.c | 94 ++- drivers/perf/Kconfig | 7 + drivers/perf/Makefile | 1 + drivers/perf/apple_m1_cpu_pmu.c | 584 ++++++++++++++++++ drivers/perf/arm_pmu.c | 2 + .../interrupt-controller/apple-aic.h | 2 + include/linux/perf/arm_pmu.h | 2 + 11 files changed, 789 insertions(+), 22 deletions(-) create mode 100644 arch/arm64/include/asm/apple_m1_pmu.h create mode 100644 drivers/perf/apple_m1_cpu_pmu.c
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 1/10 dt-bindings: arm-pmu: Document Apple PMU compatible strings
As we are about to add support fur the Apple PMUs, document the compatible strings associated with the two micro-architectures present in the Apple M1.
--- Documentation/devicetree/bindings/arm/pmu.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/arm/pmu.yaml +2 -0
@@ -20,6 +20,8 @@ properties: items: - enum: - apm,potenza-pmu + - apple,firestorm-pmu + - apple,icestorm-pmu - arm,armv8-pmuv3 # Only for s/w models - arm,arm1136-pmu - arm,arm1176-pmu
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 2/10 dt-bindings: apple,aic: Add CPU PMU per-cpu pseudo-interrupts
In reply to Marc ZyngierAdvertise the two pseudo-interrupts that tied to the two PMU flavours present in the Apple M1 SoC.
We choose the expose two different pseudo-interrupts to the OS as the e-core PMU is obviously different from the p-core one, effectively presenting two different devices.
--- .../devicetree/bindings/interrupt-controller/apple,aic.yaml | 2 ++ include/dt-bindings/interrupt-controller/apple-aic.h | 2 ++ 2 files changed, 4 insertions(+)
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +2 -0
@@ -56,6 +56,8 @@ properties: - 1: virtual HV timer - 2: physical guest timer - 3: virtual guest timer + - 4: 'efficient' CPU PMU + - 5: 'performance' CPU PMU The 3rd cell contains the interrupt flags. This is normally IRQ_TYPE_LEVEL_HIGH (4).
include/dt-bindings/interrupt-controller/apple-aic.h +2 -0
@@ -11,5 +11,7 @@#define AIC_TMR_HV_VIRT 1#define AIC_TMR_GUEST_PHYS 2#define AIC_TMR_GUEST_VIRT 3 +#define AIC_CPU_PMU_E 4 +#define AIC_CPU_PMU_P 5#endif
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 3/10 dt-bindings: apple,aic: Add affinity description for per-cpu pseudo-interrupts
In reply to Marc ZyngierSome of the FIQ per-cpu pseudo-interrupts are better described with a specific affinity, the most obvious candidate being the CPU PMUs.
Augment the AIC binding to be able to specify that affinity in the interrupt controller node.
--- .../interrupt-controller/apple,aic.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+)
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +27 -0
@@ -70,6 +70,33 @@ properties: power-domains: maxItems: 1 + affinities: + type: object + description: + FIQ affinity can be expressed as a single "affinities" node, + containing a set of sub-nodes, one per FIQ with a non-default + affinity. + patternProperties: + "^.+-affinity$": + type: object + properties: + fiq-index: + description: + The interrupt number specified as a FIQ, and for which + the affinity is not the default. + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 5 + + cpus: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Should be a list of phandles to CPU nodes (as described in + Documentation/devicetree/bindings/arm/cpus.yaml). + + required: + - fiq-index + - cpus + required: - compatible - '#interrupt-cells'
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v4 03/10] dt-bindings: apple,aic: Add affinity description for per-cpu pseudo-interrupts
Quoted 16 lines · Marc Zyngier
Some of the FIQ per-cpu pseudo-interrupts are better described with a specific affinity, the most obvious candidate being the CPU PMUs.
Augment the AIC binding to be able to specify that affinity in the interrupt controller node.
Signed-off-by Marc Zyngier <[email protected]>--- .../interrupt-controller/apple,aic.yaml | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+)Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +0
-0
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml properties: · line 74
Quoted 5 lines
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +2
-0@@ -70,6 +70,33 @@ properties: power-domains: maxItems: 1 + affinities: + type: object
additionalProperties: false
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml properties: · line 81
Quoted 7 lines
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +7
-0+ description: + FIQ affinity can be expressed as a single "affinities" node, + containing a set of sub-nodes, one per FIQ with a non-default + affinity. + patternProperties: + "^.+-affinity$": + type: object
additionalProperties: false
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml properties: · line 83
Quoted 2 lines
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +2
-0+ properties: + fiq-index:
apple,fiq-index
With that,
Quoted 23 lines
Documentation/devicetree/bindings/interrupt-controller/apple,aic.yaml +16
-0+ description: + The interrupt number specified as a FIQ, and for which + the affinity is not the default. + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 5 + + cpus: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Should be a list of phandles to CPU nodes (as described in + Documentation/devicetree/bindings/arm/cpus.yaml). + + required: + - fiq-index + - cpus + required: - compatible - '#interrupt-cells'Signature · 1 line
2.30.2
PATCH v4 4/10 irqchip/apple-aic: Parse FIQ affinities from device-tree
In reply to Marc ZyngierIn order to be able to tell the core IRQ code about the affinity of the PMU interrupt in later patches, parse the affinities kindly provided in the device-tree.
--- drivers/irqchip/irq-apple-aic.c | 49 +++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+)
drivers/irqchip/irq-apple-aic.c +49 -0
@@ -177,6 +177,9 @@ struct aic_irq_chip {void __iomem *base;struct irq_domain *hw_domain;struct irq_domain *ipi_domain; +struct { +cpumask_t aff; + } *fiq_aff[AIC_NR_FIQ ];int nr_hw;int ipi_hwirq; };
@@ -794,12 +797,50 @@ static struct gic_kvm_info vgic_info __initdata = { .no_hw_deactivation = true, }; +static void build_fiq_affinity (struct aic_irq_chip *ic,struct device_node *aff) +{ +int i, n; +u32 fiq; + +if (of_property_read_u32 (aff,"fiq-index" , &fiq) || +WARN_ON (fiq >=AIC_NR_FIQ ) || ic->fiq_aff[fiq]) +return ; + + n =of_property_count_elems_of_size (aff,"cpus" ,sizeof (u32)); +if (WARN_ON (n <0 )) +return ; + + ic->fiq_aff[fiq] =kzalloc (sizeof (ic->fiq_aff[fiq]),GFP_KERNEL ); +if (!ic->fiq_aff[fiq]) +return ; + +for (i =0 ; i < n; i++) { +struct device_node *cpu_node; +u32 cpu_phandle; +int cpu; + +if (of_property_read_u32_index (aff,"cpus" , i, &cpu_phandle)) +continue ; + + cpu_node =of_find_node_by_phandle (cpu_phandle); +if (WARN_ON (!cpu_node)) +continue ; + + cpu =of_cpu_node_to_id (cpu_node); +if (WARN_ON (cpu <0 )) +continue ; + +cpumask_set_cpu (cpu, &ic->fiq_aff[fiq]->aff); + } +} +static int __init aic_of_ic_init (struct device_node *node,struct device_node *parent) {int i;void __iomem *regs;u32 info;struct aic_irq_chip *irqc; +struct device_node *affs; regs =of_iomap (node,0 );if (WARN_ON (!regs))
@@ -833,6 +874,14 @@ static int __init aic_of_ic_init(struct device_node *node, struct device_node *preturn -ENODEV ; } + affs =of_get_child_by_name (node,"affinities" ); +if (affs) { +struct device_node *chld; + +for_each_child_of_node (affs, chld) +build_fiq_affinity (irqc, chld); + } +set_handle_irq (aic_handle_irq);set_handle_fiq (aic_handle_fiq);
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 5/10 irqchip/apple-aic: Wire PMU interrupts
In reply to Marc ZyngierAdd the necessary code to configure and P and E-core PMU interrupts with their respective affinities. When such an interrupt fires, map it onto the right pseudo-interrupt.
--- drivers/irqchip/irq-apple-aic.c | 34 +++++++++++++++++++++------------ 1 file changed, 22 insertions(+), 12 deletions(-)
drivers/irqchip/irq-apple-aic.c +22 -12
@@ -155,7 +155,7 @@#define SYS_IMP_APL_UPMSR_EL1 sys_reg(3, 7, 15, 6, 4)#define UPMSR_IACT BIT(0) -#define AIC_NR_FIQ 4 +#define AIC_NR_FIQ 6#define AIC_NR_SWIPI 32/*
@@ -416,16 +416,15 @@ static void __exception_irq_entry aic_handle_fiq(struct pt_regs *regs) aic_irqc->nr_hw + AIC_TMR_EL02_VIRT); } -if ((read_sysreg_s (SYS_IMP_APL_PMCR0_EL1 ) & (PMCR0_IMODE |PMCR0_IACT )) == - (FIELD_PREP (PMCR0_IMODE ,PMCR0_IMODE_FIQ ) |PMCR0_IACT )) { -/* -* Not supported yet, let's figure out how to handle this when -* we implement these proprietary performance counters. For now, -* just mask it and move on. -*/ -pr_err_ratelimited ("PMC FIQ fired. Masking.\n" ); -sysreg_clear_set_s (SYS_IMP_APL_PMCR0_EL1 ,PMCR0_IMODE |PMCR0_IACT , -FIELD_PREP (PMCR0_IMODE ,PMCR0_IMODE_OFF )); +if (read_sysreg_s (SYS_IMP_APL_PMCR0_EL1 ) &PMCR0_IACT ) { +int irq; +if (cpumask_test_cpu (smp_processor_id (), + &aic_irqc->fiq_aff[AIC_CPU_PMU_P ]->aff)) + irq =AIC_CPU_PMU_P ; +else + irq =AIC_CPU_PMU_E ; +generic_handle_domain_irq (aic_irqc->hw_domain, + aic_irqc->nr_hw + irq); } if (FIELD_GET(UPMCR0_IMODE, read_sysreg_s(SYS_IMP_APL_UPMCR0_EL1)) == UPMCR0_IMODE_FIQ &&
@@ -465,7 +464,18 @@ static int aic_irq_domain_map(struct irq_domain *id, unsigned int irq, handle_fasteoi_irq, NULL, NULL);irqd_set_single_target (irq_desc_get_irq_data (irq_to_desc (irq))); }else { -irq_set_percpu_devid (irq); +int fiq = hw - ic->nr_hw; + +switch (fiq) { +case AIC_CPU_PMU_P : +case AIC_CPU_PMU_E : +irq_set_percpu_devid_partition (irq, &ic->fiq_aff[fiq]->aff); +break ; +default : +irq_set_percpu_devid (irq); +break ; + } +irq_domain_set_info (id, irq, hw, &fiq_chip, id->host_data, handle_percpu_devid_irq,NULL ,NULL ); }
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 6/10 arm64: dts: apple: Add t8103 PMU interrupt affinities
In reply to Marc ZyngierThe two PMU pseudo interrupts have specific affinities. One set is affine to the small cores, and the other set affine to the big ones.
--- arch/arm64/boot/dts/apple/t8103.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/apple/t8103.dtsi +12 -0
@@ -213,6 +213,18 @@ aic: interrupt-controller@23b100000 { interrupt-controller; reg = <0x2 0x3b100000 0x0 0x8000>; power-domains = <&ps_aic>; + + affinities { + e-core-pmu-affinity { + fiq-index = <AIC_CPU_PMU_E>; + cpus = <&cpu0 &cpu1 &cpu2 &cpu3>; + }; + + p-core-pmu-affinity { + fiq-index = <AIC_CPU_PMU_P>; + cpus = <&cpu4 &cpu5 &cpu6 &cpu7>; + }; + }; }; pmgr: power-management@23b700000 {
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 7/10 arm64: dts: apple: Add t8303 PMU nodes
In reply to Marc ZyngierAdvertise the two PMU nodes for the t8103 SoC.
--- arch/arm64/boot/dts/apple/t8103.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+)
arch/arm64/boot/dts/apple/t8103.dtsi +12 -0
@@ -97,6 +97,18 @@ timer { <AIC_FIQ AIC_TMR_HV_VIRT IRQ_TYPE_LEVEL_HIGH>; }; + pmu-e { + compatible = "apple,icestorm-pmu"; + interrupt-parent = <&aic>; + interrupts = <AIC_FIQ AIC_CPU_PMU_E IRQ_TYPE_LEVEL_HIGH>; + }; + + pmu-p { + compatible = "apple,firestorm-pmu"; + interrupt-parent = <&aic>; + interrupts = <AIC_FIQ AIC_CPU_PMU_P IRQ_TYPE_LEVEL_HIGH>; + }; + clkref: clock-ref { compatible = "fixed-clock"; #clock-cells = <0>;
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 8/10 irqchip/apple-aic: Move PMU-specific registers to their own include file
In reply to Marc ZyngierAs we are about to have a PMU driver, move the PMU bits from the AIC driver into a common include file.
--- arch/arm64/include/asm/apple_m1_pmu.h | 19 +++++++++++++++++++ drivers/irqchip/irq-apple-aic.c | 11 +---------- 2 files changed, 20 insertions(+), 10 deletions(-) create mode 100644 arch/arm64/include/asm/apple_m1_pmu.h
arch/arm64/include/asm/apple_m1_pmu.h new file +19 -0
@@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 + +#ifndef __ASM_APPLE_M1_PMU_h +#define __ASM_APPLE_M1_PMU_h + +#include <linux/bits.h> +#include <asm/sysreg.h> + +/* Core PMC control register */ +#define SYS_IMP_APL_PMCR0_EL1 sys_reg(3, 1, 15, 0, 0) +#define PMCR0_IMODE GENMASK(10, 8) +#define PMCR0_IMODE_OFF 0 +#define PMCR0_IMODE_PMI 1 +#define PMCR0_IMODE_AIC 2 +#define PMCR0_IMODE_HALT 3 +#define PMCR0_IMODE_FIQ 4 +#define PMCR0_IACT BIT(11) + +#endif /* __ASM_APPLE_M1_PMU_h */
drivers/irqchip/irq-apple-aic.c +1 -10
@@ -55,6 +55,7 @@#include <linux/limits.h> #include <linux/of_address.h> #include <linux/slab.h> +#include <asm/apple_m1_pmu.h> #include <asm/exception.h> #include <asm/sysreg.h> #include <asm/virt.h>
@@ -109,16 +110,6 @@* Note: sysreg-based IPIs are not supported yet. */ -/* Core PMC control register */ -#define SYS_IMP_APL_PMCR0_EL1 sys_reg(3, 1, 15, 0, 0) -#define PMCR0_IMODE GENMASK(10, 8) -#define PMCR0_IMODE_OFF 0 -#define PMCR0_IMODE_PMI 1 -#define PMCR0_IMODE_AIC 2 -#define PMCR0_IMODE_HALT 3 -#define PMCR0_IMODE_FIQ 4 -#define PMCR0_IACT BIT(11) -/* IPI request registers */ #define SYS_IMP_APL_IPI_RR_LOCAL_EL1 sys_reg(3, 5, 15, 0, 0)#define SYS_IMP_APL_IPI_RR_GLOBAL_EL1 sys_reg(3, 5, 15, 0, 1)
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 9/10 drivers/perf: arm_pmu: Handle 47 bit counters
In reply to Marc ZyngierThe current ARM PMU framework can only deal with 32 or 64bit counters. Teach it about a 47bit flavour.
Yes, this is odd.
--- drivers/perf/arm_pmu.c | 2 ++ include/linux/perf/arm_pmu.h | 2 ++ 2 files changed, 4 insertions(+)
drivers/perf/arm_pmu.c +2 -0
@@ -109,6 +109,8 @@ static inline u64 arm_pmu_event_max_period(struct perf_event *event) {if (event->hw.flags &ARMPMU_EVT_64BIT )return GENMASK_ULL (63 ,0 ); +else if (event->hw.flags &ARMPMU_EVT_47BIT ) +return GENMASK_ULL (46 ,0 );else return GENMASK_ULL (31 ,0 ); }
include/linux/perf/arm_pmu.h +2 -0
@@ -26,6 +26,8 @@*/ /* Event uses a 64bit counter */ #define ARMPMU_EVT_64BIT 1 +/* Event uses a 47bit counter */ +#define ARMPMU_EVT_47BIT 2#define HW_OP_UNSUPPORTED 0xFFFF#define C (_x) PERF_COUNT_HW_CACHE_##_x
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v4 10/10 drivers/perf: Add Apple icestorm/firestorm CPU PMU driver
In reply to Marc ZyngierAdd a new, weird and wonderful driver for the equally weird Apple PMU HW. Although the PMU itself is functional, we don't know much about the events yet, so this can be considered as yet another random number generator...
Nonetheless, it can reliably count at least cycles and instructions in the usually wonky big-little way. For anything else, it of course supports raw event numbers.
--- arch/arm64/include/asm/apple_m1_pmu.h | 45 ++ drivers/perf/Kconfig | 7 + drivers/perf/Makefile | 1 + drivers/perf/apple_m1_cpu_pmu.c | 584 ++++++++++++++++++++++++++ 4 files changed, 637 insertions(+) create mode 100644 drivers/perf/apple_m1_cpu_pmu.c
arch/arm64/include/asm/apple_m1_pmu.h +45 -0
@@ -6,8 +6,21 @@#include <linux/bits.h> #include <asm/sysreg.h> +/* Counters */ +#define SYS_IMP_APL_PMC0_EL1 sys_reg(3, 2, 15, 0, 0) +#define SYS_IMP_APL_PMC1_EL1 sys_reg(3, 2, 15, 1, 0) +#define SYS_IMP_APL_PMC2_EL1 sys_reg(3, 2, 15, 2, 0) +#define SYS_IMP_APL_PMC3_EL1 sys_reg(3, 2, 15, 3, 0) +#define SYS_IMP_APL_PMC4_EL1 sys_reg(3, 2, 15, 4, 0) +#define SYS_IMP_APL_PMC5_EL1 sys_reg(3, 2, 15, 5, 0) +#define SYS_IMP_APL_PMC6_EL1 sys_reg(3, 2, 15, 6, 0) +#define SYS_IMP_APL_PMC7_EL1 sys_reg(3, 2, 15, 7, 0) +#define SYS_IMP_APL_PMC8_EL1 sys_reg(3, 2, 15, 9, 0) +#define SYS_IMP_APL_PMC9_EL1 sys_reg(3, 2, 15, 10, 0) +/* Core PMC control register */ #define SYS_IMP_APL_PMCR0_EL1 sys_reg(3, 1, 15, 0, 0) +#define PMCR0_CNT_ENABLE_0_7 GENMASK(7, 0)#define PMCR0_IMODE GENMASK(10, 8)#define PMCR0_IMODE_OFF 0#define PMCR0_IMODE_PMI 1
@@ -15,5 +28,37 @@#define PMCR0_IMODE_HALT 3#define PMCR0_IMODE_FIQ 4#define PMCR0_IACT BIT(11) +#define PMCR0_PMI_ENABLE_0_7 GENMASK(19, 12) +#define PMCR0_STOP_CNT_ON_PMI BIT(20) +#define PMCR0_CNT_GLOB_L2C_EVT BIT(21) +#define PMCR0_DEFER_PMI_TO_ERET BIT(22) +#define PMCR0_ALLOW_CNT_EN_EL0 BIT(30) +#define PMCR0_CNT_ENABLE_8_9 GENMASK(33, 32) +#define PMCR0_PMI_ENABLE_8_9 GENMASK(45, 44) + +#define SYS_IMP_APL_PMCR1_EL1 sys_reg(3, 1, 15, 1, 0) +#define PMCR1_COUNT_A64_EL0_0_7 GENMASK(15, 8) +#define PMCR1_COUNT_A64_EL1_0_7 GENMASK(23, 16) +#define PMCR1_COUNT_A64_EL0_8_9 GENMASK(41, 40) +#define PMCR1_COUNT_A64_EL1_8_9 GENMASK(49, 48) + +#define SYS_IMP_APL_PMCR2_EL1 sys_reg(3, 1, 15, 2, 0) +#define SYS_IMP_APL_PMCR3_EL1 sys_reg(3, 1, 15, 3, 0) +#define SYS_IMP_APL_PMCR4_EL1 sys_reg(3, 1, 15, 4, 0) + +#define SYS_IMP_APL_PMESR0_EL1 sys_reg(3, 1, 15, 5, 0) +#define PMESR0_EVT_CNT_2 GENMASK(7, 0) +#define PMESR0_EVT_CNT_3 GENMASK(15, 8) +#define PMESR0_EVT_CNT_4 GENMASK(23, 16) +#define PMESR0_EVT_CNT_5 GENMASK(31, 24) + +#define SYS_IMP_APL_PMESR1_EL1 sys_reg(3, 1, 15, 6, 0) +#define PMESR1_EVT_CNT_6 GENMASK(7, 0) +#define PMESR1_EVT_CNT_7 GENMASK(15, 8) +#define PMESR1_EVT_CNT_8 GENMASK(23, 16) +#define PMESR1_EVT_CNT_9 GENMASK(31, 24) + +#define SYS_IMP_APL_PMSR_EL1 sys_reg(3, 1, 15, 13, 0) +#define PMSR_OVERFLOW GENMASK(9, 0)#endif /* __ASM_APPLE_M1_PMU_h */
drivers/perf/Kconfig +7 -0
@@ -146,6 +146,13 @@ config MARVELL_CN10K_TAD_PMU Provides support for Last-Level cache Tag-and-data Units (LLC-TAD) performance monitors on CN10K family silicons. +config APPLE_M1_CPU_PMU + bool "Apple M1 CPU PMU support" + depends on ARM_PMU && ARCH_APPLE + help + Provides support for the non-architectural CPU PMUs present on + the Apple M1 SoCs and derivatives. + source "drivers/perf/hisilicon/Kconfig" endmenu
drivers/perf/Makefile +1 -0
@@ -15,3 +15,4 @@ obj-$(CONFIG_XGENE_PMU) += xgene_pmu.o obj-$(CONFIG_ARM_SPE_PMU) += arm_spe_pmu.o obj-$(CONFIG_ARM_DMC620_PMU) += arm_dmc620_pmu.o obj-$(CONFIG_MARVELL_CN10K_TAD_PMU) += marvell_cn10k_tad_pmu.o +obj-$(CONFIG_APPLE_M1_CPU_PMU) += apple_m1_cpu_pmu.o
drivers/perf/apple_m1_cpu_pmu.c new file +584 -0
584 lines not on this page · raw message
Signature · 7 lines
2.30.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel