configs/friendlyarm_nanopi_r2s: new defconfig
PATCH v3 1/1 configs/friendlyarm_nanopi_r2s: new defconfig
The NanoPi R2S is a FriendlyElec mini-router based on:
- Rockchip RK3328 SoC
- 1GB (or 2GB) DDR4 RAM
- Gigabit Ethernet (WAN)
- Gigabit Ethernet (USB3) (LAN)
- USB 2.0 Host Port
- MicroSD slot
- Reset button
- WAN - LAN - SYS LED
https://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=282
---
Changes v1 -> v2:
- Drop VFAT partition (kernel, DTB and ext4linux.conf in ext4 partition)
Changes v2 -> v3:
- Use fixed versions of u-boot, kernel and TF-A
--- DEVELOPERS | 2 + board/friendlyarm/nanopi-r2s/extlinux.conf | 4 ++ board/friendlyarm/nanopi-r2s/genimage.cfg | 22 +++++++++ board/friendlyarm/nanopi-r2s/post-build.sh | 5 ++ board/friendlyarm/nanopi-r2s/readme.txt | 57 ++++++++++++++++++++++ configs/friendlyarm_nanopi_r2s_defconfig | 41 ++++++++++++++++ 6 files changed, 131 insertions(+) create mode 100644 board/friendlyarm/nanopi-r2s/extlinux.conf create mode 100644 board/friendlyarm/nanopi-r2s/genimage.cfg create mode 100755 board/friendlyarm/nanopi-r2s/post-build.sh create mode 100644 board/friendlyarm/nanopi-r2s/readme.txt create mode 100644 configs/friendlyarm_nanopi_r2s_defconfig
DEVELOPERS +2 -0
@@ -1073,7 +1073,9 @@ F: configs/qemu_* N: Gilles Talis <[email protected]> F: board/freescale/imx8mmevk/ +F: board/friendlyarm/nanopi-r2s/ F: configs/freescale_imx8mmevk_defconfig +F: configs/friendlyarm_nanopi_r2s_defconfig F: package/cctz/ F: package/faad2/ F: package/fdk-aac/
board/friendlyarm/nanopi-r2s/extlinux.conf new file +4 -0
@@ -0,0 +1,4 @@ +label NanoPi R2S linux + kernel /boot/Image + devicetree /boot/rk3328-nanopi-r2s.dtb + append root=/dev/mmcblk0p1 rw rootwait
board/friendlyarm/nanopi-r2s/genimage.cfg new file +22 -0
@@ -0,0 +1,22 @@ +image sdcard.img { + hdimage { + } + + partition u-boot-tpl-spl-dtb { + in-partition-table = "no" + image = "idbloader.img" + offset = 32K + } + + partition u-boot-dtb { + in-partition-table = "no" + image = "u-boot.itb" + offset = 8M + } + + partition rootfs { + partition-type = 0x83 + offset = 16M + image = "rootfs.ext4" + } +}
board/friendlyarm/nanopi-r2s/post-build.sh new file +5 -0
@@ -0,0 +1,5 @@ +#!/bin/sh + +BOARD_DIR="$(dirname $0)" + +install -m 0644 -D $BOARD_DIR/extlinux.conf $TARGET_DIR/boot/extlinux/extlinux.conf
board/friendlyarm/nanopi-r2s/readme.txt new file +57 -0
57 lines not on this page · raw message
configs/friendlyarm_nanopi_r2s_defconfig new file +41 -0
41 lines not on this page · raw message
Signature · 6 lines
2.32.0 _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Hi Giles,
Quoted 72 lines · Gilles Talis
The NanoPi R2S is a FriendlyElec mini-router based on:
- Rockchip RK3328 SoC
- 1GB (or 2GB) DDR4 RAM
- Gigabit Ethernet (WAN)
- Gigabit Ethernet (USB3) (LAN)
- USB 2.0 Host Port
- MicroSD slot
- Reset button
- WAN - LAN - SYS LEDhttps://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=282
Signed-off-by Gilles Talis <[email protected]>---
Changes v1 -> v2:
- Drop VFAT partition (kernel, DTB and ext4linux.conf in ext4 partition)Changes v2 -> v3:
- Use fixed versions of u-boot, kernel and TF-A--- DEVELOPERS | 2 + board/friendlyarm/nanopi-r2s/extlinux.conf | 4 ++ board/friendlyarm/nanopi-r2s/genimage.cfg | 22 +++++++++ board/friendlyarm/nanopi-r2s/post-build.sh | 5 ++ board/friendlyarm/nanopi-r2s/readme.txt | 57 ++++++++++++++++++++++ configs/friendlyarm_nanopi_r2s_defconfig | 41 ++++++++++++++++ 6 files changed, 131 insertions(+)create mode 100644
board/friendlyarm/nanopi-r2s/extlinux.confcreate mode 100644 board/friendlyarm/nanopi-r2s/genimage.cfg create mode 100755board/friendlyarm/nanopi-r2s/post-build.shcreate mode 100644board/friendlyarm/nanopi-r2s/readme.txtcreate mode 100644 configs/friendlyarm_nanopi_r2s_defconfigDEVELOPERS +2
-0@@ -1073,7 +1073,9 @@ F: configs/qemu_* N: Gilles Talis <[email protected]> F: board/freescale/imx8mmevk/ +F: board/friendlyarm/nanopi-r2s/ F: configs/freescale_imx8mmevk_defconfig +F: configs/friendlyarm_nanopi_r2s_defconfig F: package/cctz/ F: package/faad2/ F: package/fdk-aac/board/friendlyarm/nanopi-r2s/extlinux.conf new file +4
-0@@ -0,0 +1,4 @@ +label NanoPi R2S linux + kernel /boot/Image + devicetree /boot/rk3328-nanopi-r2s.dtb + append root=/dev/mmcblk0p1 rw rootwaitboard/friendlyarm/nanopi-r2s/genimage.cfg new file +8
-0@@ -0,0 +1,22 @@ +image sdcard.img { + hdimage { + } + + partition u-boot-tpl-spl-dtb { + in-partition-table = "no" + image = "idbloader.img" + offset = 32K
board/friendlyarm/nanopi-r2s/genimage.cfg line 18
Quoted 10 lines
board/friendlyarm/nanopi-r2s/genimage.cfg new file +10
-0+ } + + partition u-boot-dtb { + in-partition-table = "no" + image = "u-boot.itb" + offset = 8M + } + + partition rootfs { + partition-type = 0x83
This ^^^ will fail due to latest genimage version. You can't specify partition-type anymore but you have to specify:
partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae
That means "Root partition (64-bit ARM/AArch64)", check this out:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
Quoted 84 lines
board/friendlyarm/nanopi-r2s/genimage.cfg new file +4
-0+ offset = 16M + image = "rootfs.ext4" + } +}board/friendlyarm/nanopi-r2s/post-build.sh new file +5
-0@@ -0,0 +1,5 @@ +#!/bin/sh + +BOARD_DIR="$(dirname $0)" + +install -m 0644 -D $BOARD_DIR/extlinux.conf $TARGET_DIR/boot/extlinux/extlinux.confboard/friendlyarm/nanopi-r2s/readme.txt new file +57
-0@@ -0,0 +1,57 @@ +Intro +===== + +This default configuration will allow you to start experimenting with the +buildroot environment for the Nanopi R2S. With the current configuration +it will bring-up the board, and allow access through the serial console. + +Nanopi R2S link: +https://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=282 + +This configuration uses ATF, U-Boot mainline and kernel mainline. + +How to build +============ + + $ make friendlyarm_nanopi_r2s_defconfig + $ make + +Note: you will need access to the internet to download the required +sources. + +Files created in output directory +================================= + +output/images + +├── bl31.elf +├── boot.vfat +├── extlinux +├── idbloader.img +├── Image +├── rk3328-nanopi-r2s.dtb +├── rootfs.ext2 +├── rootfs.ext4 -> rootfs.ext2 +├── rootfs.tar +├── sdcard.img +├── u-boot.bin +└── u-boot.itb + +How to write the SD card +======================== + +Once the build process is finished you will have an image called "sdcard.img" +in the output/images/ directory. + +Copy the bootable "sdcard.img" onto an SD card with "dd": + + $ sudo dd if=output/images/sdcard.img of=/dev/sdX + $ sudo sync + +Insert the micro SDcard in your Nanopi R2S and power it up. The console +is on the serial line, 1500000 8N1. + +Notes +===== + +This configuration can also be used to drive the Friendlyarm Nanopi Neo3 board.configs/friendlyarm_nanopi_r2s_defconfig new file +0
-0
configs/friendlyarm_nanopi_r2s_defconfig line 2
Quoted 2 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +2
-0@@ -0,0 +1,41 @@ +BR2_aarch64=y +BR2_ARM_FPU_VFPV4=y
On aarch64 this ^^^ became useless so you can drop it
Quoted 29 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +29
-0+BR2_TARGET_GENERIC_HOSTNAME="rk3328-nanopi-r2s" +BR2_TARGET_GENERIC_ISSUE="Welcome to Nanopi R2S RK3328" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/friendlyarm/nanopi-r2s/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/friendlyarm/nanopi-r2s/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.16" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="rockchip/rk3328-nanopi-r2s" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="120M" +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.5" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="rk3328" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN=y +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2021.10" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="nanopi-r2s-rk3328" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYTHON3=y
configs/friendlyarm_nanopi_r2s_defconfig line 41
Quoted 10 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +10
-0+BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31_ELF=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.itb" +BR2_TARGET_UBOOT_SPL=y +BR2_TARGET_UBOOT_SPL_NAME="idbloader.img" +BR2_PACKAGE_HOST_DOSFSTOOLS=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_MTOOLS=y +BR2_PACKAGE_HOST_UBOOT_TOOLS=y
Have you tested this defconfig with Gitlab-CI docker? registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314
It helps to check if any possible host tool is missing.
Can you give a go with it?
Thank you!
Best regards
Signature · 6 lines
Giulio Benetti Benetti Engineering sas _______________________________________________ buildroot mailing list [email protected] https://lists.buildroot.org/mailman/listinfo/buildroot
Hi Gilles,
Quoted 90 lines · Giulio Benetti
Hi Giles,
Quoted 72 lines · Gilles Talis
The NanoPi R2S is a FriendlyElec mini-router based on:
- Rockchip RK3328 SoC
- 1GB (or 2GB) DDR4 RAM
- Gigabit Ethernet (WAN)
- Gigabit Ethernet (USB3) (LAN)
- USB 2.0 Host Port
- MicroSD slot
- Reset button
- WAN - LAN - SYS LEDhttps://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=282
Signed-off-by Gilles Talis <[email protected]>---
Changes v1 -> v2:
- Drop VFAT partition (kernel, DTB and ext4linux.conf in ext4 partition)Changes v2 -> v3:
- Use fixed versions of u-boot, kernel and TF-A--- DEVELOPERS | 2 + board/friendlyarm/nanopi-r2s/extlinux.conf | 4 ++ board/friendlyarm/nanopi-r2s/genimage.cfg | 22 +++++++++ board/friendlyarm/nanopi-r2s/post-build.sh | 5 ++ board/friendlyarm/nanopi-r2s/readme.txt | 57 ++++++++++++++++++++++ configs/friendlyarm_nanopi_r2s_defconfig | 41 ++++++++++++++++ 6 files changed, 131 insertions(+)create mode 100644
board/friendlyarm/nanopi-r2s/extlinux.confcreate mode 100644 board/friendlyarm/nanopi-r2s/genimage.cfg create mode 100755board/friendlyarm/nanopi-r2s/post-build.shcreate mode 100644board/friendlyarm/nanopi-r2s/readme.txtcreate mode 100644 configs/friendlyarm_nanopi_r2s_defconfigDEVELOPERS +2
-0@@ -1073,7 +1073,9 @@ F: configs/qemu_* N: Gilles Talis <[email protected]> F: board/freescale/imx8mmevk/ +F: board/friendlyarm/nanopi-r2s/ F: configs/freescale_imx8mmevk_defconfig +F: configs/friendlyarm_nanopi_r2s_defconfig F: package/cctz/ F: package/faad2/ F: package/fdk-aac/board/friendlyarm/nanopi-r2s/extlinux.conf new file +4
-0@@ -0,0 +1,4 @@ +label NanoPi R2S linux + kernel /boot/Image + devicetree /boot/rk3328-nanopi-r2s.dtb + append root=/dev/mmcblk0p1 rw rootwaitboard/friendlyarm/nanopi-r2s/genimage.cfg new file +8
-0@@ -0,0 +1,22 @@ +image sdcard.img { + hdimage { + } + + partition u-boot-tpl-spl-dtb { + in-partition-table = "no" + image = "idbloader.img" + offset = 32Kboard/friendlyarm/nanopi-r2s/genimage.cfg line 18
Quoted 10 lines
board/friendlyarm/nanopi-r2s/genimage.cfg new file +10
-0+ } + + partition u-boot-dtb { + in-partition-table = "no" + image = "u-boot.itb" + offset = 8M + } + + partition rootfs { + partition-type = 0x83This ^^^ will fail due to latest genimage version. You can't specify partition-type anymore but you have to specify:
partition-type-uuid = b921b045-1df0-41c3-af44-4c6f280d3fae
Quoted 2 lines
That means "Root partition (64-bit ARM/AArch64)", check this out:
https://en.wikipedia.org/wiki/GUID_Partition_Table#Partition_type_GUIDs
This is not true since you're not using "gpt" partition table. So you leave:
partition-type = 0x83
Sorry for the noise!
Best regards
Signature · 2 lines
Giulio Benetti Benetti Engineering sas
Quoted 132 lines
Quoted 84 lines
board/friendlyarm/nanopi-r2s/genimage.cfg new file +4
-0+ offset = 16M + image = "rootfs.ext4" + } +}board/friendlyarm/nanopi-r2s/post-build.sh new file +5
-0@@ -0,0 +1,5 @@ +#!/bin/sh + +BOARD_DIR="$(dirname $0)" + +install -m 0644 -D $BOARD_DIR/extlinux.conf $TARGET_DIR/boot/extlinux/extlinux.confboard/friendlyarm/nanopi-r2s/readme.txt new file +57
-0@@ -0,0 +1,57 @@ +Intro +===== + +This default configuration will allow you to start experimenting with the +buildroot environment for the Nanopi R2S. With the current configuration +it will bring-up the board, and allow access through the serial console. + +Nanopi R2S link: +https://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=282 + +This configuration uses ATF, U-Boot mainline and kernel mainline. + +How to build +============ + + $ make friendlyarm_nanopi_r2s_defconfig + $ make + +Note: you will need access to the internet to download the required +sources. + +Files created in output directory +================================= + +output/images + +├── bl31.elf +├── boot.vfat +├── extlinux +├── idbloader.img +├── Image +├── rk3328-nanopi-r2s.dtb +├── rootfs.ext2 +├── rootfs.ext4 -> rootfs.ext2 +├── rootfs.tar +├── sdcard.img +├── u-boot.bin +└── u-boot.itb + +How to write the SD card +======================== + +Once the build process is finished you will have an image called "sdcard.img" +in the output/images/ directory. + +Copy the bootable "sdcard.img" onto an SD card with "dd": + + $ sudo dd if=output/images/sdcard.img of=/dev/sdX + $ sudo sync + +Insert the micro SDcard in your Nanopi R2S and power it up. The console +is on the serial line, 1500000 8N1. + +Notes +===== + +This configuration can also be used to drive the Friendlyarm Nanopi Neo3 board.configs/friendlyarm_nanopi_r2s_defconfig new file +0
-0configs/friendlyarm_nanopi_r2s_defconfig line 2
Quoted 2 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +2
-0@@ -0,0 +1,41 @@ +BR2_aarch64=y +BR2_ARM_FPU_VFPV4=yOn aarch64 this ^^^ became useless so you can drop it
Quoted 29 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +29
-0+BR2_TARGET_GENERIC_HOSTNAME="rk3328-nanopi-r2s" +BR2_TARGET_GENERIC_ISSUE="Welcome to Nanopi R2S RK3328" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/friendlyarm/nanopi-r2s/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/friendlyarm/nanopi-r2s/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.16" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="rockchip/rk3328-nanopi-r2s" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="120M" +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.5" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="rk3328" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN=y +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2021.10" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="nanopi-r2s-rk3328" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYTHON3=yconfigs/friendlyarm_nanopi_r2s_defconfig line 41
Quoted 10 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +10
-0+BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31_ELF=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.itb" +BR2_TARGET_UBOOT_SPL=y +BR2_TARGET_UBOOT_SPL_NAME="idbloader.img" +BR2_PACKAGE_HOST_DOSFSTOOLS=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_MTOOLS=y +BR2_PACKAGE_HOST_UBOOT_TOOLS=yHave you tested this defconfig with Gitlab-CI docker? registry.gitlab.com/buildroot.org/buildroot/base:20220105.2314
Quoted 7 lines
It helps to check if any possible host tool is missing.
Can you give a go with it?
Thank you!
Best regards
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot
Arnout Vandecappelle
AppliedQuoted 14 lines · Gilles Talis
The NanoPi R2S is a FriendlyElec mini-router based on:
- Rockchip RK3328 SoC
- 1GB (or 2GB) DDR4 RAM
- Gigabit Ethernet (WAN)
- Gigabit Ethernet (USB3) (LAN)
- USB 2.0 Host Port
- MicroSD slot
- Reset button
- WAN - LAN - SYS LEDhttps://www.friendlyarm.com/index.php?route=product/product&path=69&product_id=282
Signed-off-by Gilles Talis <[email protected]>
[snip]
configs/friendlyarm_nanopi_r2s_defconfig line 1
Quoted 7 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +1
-0@@ -0,0 +1,41 @@ +BR2_aarch64=y
I've added an explicit BR2_cortex_a53=y
Quoted 20 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +20
-0+BR2_ARM_FPU_VFPV4=y +BR2_TARGET_GENERIC_HOSTNAME="rk3328-nanopi-r2s" +BR2_TARGET_GENERIC_ISSUE="Welcome to Nanopi R2S RK3328" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/friendlyarm/nanopi-r2s/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c board/friendlyarm/nanopi-r2s/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.16" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="rockchip/rk3328-nanopi-r2s" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_LINUX_KERNEL_NEEDS_HOST_OPENSSL=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="120M" +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.5"
configs/friendlyarm_nanopi_r2s_defconfig line 31
Quoted 10 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +10
-0+BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="rk3328" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_NEEDS_ARM32_TOOLCHAIN=y +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2021.10" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="nanopi-r2s-rk3328" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_PYTHON3=y
python3 is not enough, it uses pylibfdt, so I added
BR2_TARGET_UBOOT_NEEDS_PYLIBFDT=y
configs/friendlyarm_nanopi_r2s_defconfig line 38
Quoted 7 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +7
-0+BR2_TARGET_UBOOT_NEEDS_ATF_BL31=y +BR2_TARGET_UBOOT_NEEDS_ATF_BL31_ELF=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM=y +BR2_TARGET_UBOOT_FORMAT_CUSTOM_NAME="u-boot.itb" +BR2_TARGET_UBOOT_SPL=y +BR2_TARGET_UBOOT_SPL_NAME="idbloader.img" +BR2_PACKAGE_HOST_DOSFSTOOLS=y
Since you switch to ext4-only, dosfstools and mtools are not longer needed, so
I removed those.
configs/friendlyarm_nanopi_r2s_defconfig line 41
Quoted 3 lines
configs/friendlyarm_nanopi_r2s_defconfig new file +3
-0+BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_MTOOLS=y +BR2_PACKAGE_HOST_UBOOT_TOOLS=y
I don't think this is needed either, but I wasn't 100% sure so I kept it.
Applied to master with those changes, thanks.
Regards,
Arnout
_______________________________________________
buildroot mailing list
[email protected]
https://lists.buildroot.org/mailman/listinfo/buildroot