Skip to contentSkip to conversation

i2c: piix4: Replace cd6h/cd7h port I/O accesses with MMIO accesses

PATCH In review Terry Bowman 3 participants 18 messages Feb 9, 2022 – Feb 15, 2022

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v5 cover i2c: piix4: Replace cd6h/cd7h port I/O accesses with MMIO accesses

This series changes the piix4_smbus driver's cd6h/cd7h port I/O accesses to use MMIO instead. This is necessary because cd6h/cd7h port I/O may be disabled on later AMD processors.

This series includes patches with MMIO accesses to register FCH::PM::DECODEEN. The same register is also accessed by the sp5100_tco driver.[1] Synchronization to the MMIO register is required in both drivers.

The first patch creates a macro to request MMIO region using the 'muxed' retry logic. This is used in patch 6 to synchronize accesses to EFCH MMIO.

The second patch replaces a hardcoded region size with a #define. This is to improve maintainability and was requested from v2 review.

The third patch moves duplicated region request/release code into functions. This locates related code into functions and reduces code line count. This will also make adding MMIO support in patch 6 easier.

The fourth patch moves SMBus controller address detection into a function. This is in preparation for adding MMIO region support.

The fifth patch moves EFCH port selection into a function. This is in preparation for adding MMIO region support.

The sixth patch adds MMIO support for region requesting/releasing and mapping. This is necessary for using MMIO to detect SMBus controller address, enable SMBbus controller region, and control the port select.

The seventh patch updates the SMBus controller address detection to support using MMIO. This is necessary because the driver accesses register FCH::PM::DECODEEN during initialization and only available using MMIO on later AMD processors.

The eighth patch updates the SMBus port selection to support MMIO. This is required because port selection control resides in the FCH::PM::DECODEEN[smbus0sel] and is only accessible using MMIO on later AMD processors.

The ninth patch enables the EFCH MMIO functionality added earlier in this series. The SMBus controller's PCI revision ID is used to check if EFCH MMIO is supported by HW and should be enabled in the driver.

Based on v5.17-rc2.

Testing:
Tested on family 19h using:
i2cdetect -y 0
i2cdetect -y 2

- Results using v5.16 and this pachset applied. Below

    shows the devices detected on the busses:
    
    # i2cdetect -y 0 
         0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
    00:                         -- -- -- -- -- -- -- -- 
    10: 10 11 -- -- -- -- -- -- 18 -- -- -- -- -- -- -- 
    20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    30: 30 -- -- -- -- 35 36 -- -- -- -- -- -- -- -- -- 
    40: -- -- -- -- -- -- -- -- -- -- 4a -- -- -- -- -- 
    50: 50 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    70: -- -- -- 73 -- -- -- --                         
    # i2cdetect -y 2
         0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
    00:                         -- -- -- -- -- -- -- -- 
    10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    40: -- -- -- -- -- -- -- -- -- -- -- -- 4c -- -- -- 
    50: -- 51 -- -- 54 -- -- -- -- -- -- -- -- -- -- -- 
    60: 60 -- -- 63 -- -- 66 -- -- -- -- 6b -- -- 6e -- 
    70: 70 71 72 73 74 75 -- 77

Also tested using sp5100_tco submitted series listed below.[1] I applied the sp5100_tco v4 series and ran:
cat >> /dev/watchdog

[1] sp5100_tco v4 patchset can be found here:

Changes in v5:
- Use request/release helper function for sb800 device in piix4_setup_sb800(). Patch 3. (Jean Delvare)
- Revert 'piix4_smba' variable definition ordering back as it was in piix4_setup_sb800(). Patch 4. (Jean Delvare)
- Add newline after piix4_sb800_port_sel(). Patch 5. (Jean Delvare)
- Remove unnecessary initialization in piix4_add_adapter(). Patch 6. (Jean Delvare)
- Remove unnecessary #define AMD_PCI_SMBUS_REVISION_MMIO. Patch 9. (Jean Delvare)
- Add description for 0x51 constant moved in the above item. This is in piix4_sb800_use_mmio(). Patch 9. (Andy Shevchenko)
- Rebase to v5.17-rc2. (Andy Shevchenko)
- Update patch 9 description. (Terry Bowman)

Changes in v4:
- Changed request_muxed_mem_region() macro to request_mem_region_muxed() in patch 1. (Andy Shevchenko)
- Removed unnecessary newline where possible in calls to request_muxed_region() in patch 2. (Terry Bowman)
- Changed piix4_sb800_region_setup() to piix4_sb800_region_request(). Patch 3. (Jean Delvare)
- Reordered piix4_setup_sb800() local variables from longest name length to shortest name length. Patch 4. (Terry Bowman)
- Changed piix4_sb800_region_request() and piix4_sb800_region_release() by adding early return() to remove 'else' improving readability. Patch 6. (Terry Bowman)
- Removed iowrite32(ioread32(...), ...). Unnecessary because MMIO is already enabled. (Terry Bowman)
- Refactored piix4_sb800_port_sel() to simplify the 'if' statement using temp variable. Patch 8. (Terry Bowman)
- Added mmio_cfg.use_mmio assignment in piix4_add_adapter(). This is needed for calls to piix4_sb800_port_sel() after initialization during normal operation. Patch 9. (Terry Bowman)

Changes in v3:
- Added request_muxed_mem_region() patch (Wolfram, Guenter)
- Reduced To/Cc list length. (Andy)

Changes in v2:
- Split single patch. (Jean Delvare)
- Replace constant 2 with SB800_PIIX4_SMB_MAP_SIZE where appropriate. (Jean Delvare)
- Shorten SB800_PIIX4_FCH_PM_DECODEEN_MMIO_EN name length to SB800_PIIX4_FCH_PM_DECODEEN_MMIO. (Jean Delvare)
- Change AMD_PCI_SMBUS_REVISION_MMIO from 0x59 to 0x51. (Terry Bowman)
- Change piix4_sb800_region_setup() to piix4_sb800_region_request(). (Jean Delvare)
- Change 'SMB' text in logging to 'SMBus' (Jean Delvare)
- Remove unnecessary NULL assignment in piix4_sb800_region_release(). (Jean Delvare)
- Move 'u8' variable definitions to single line. (Jean Delvare)
- Hardcode piix4_setup_sb800_smba() return value to 0 since it is always
0. (Jean Delvare)

Terry Bowman (9):
kernel/resource: Introduce request_mem_region_muxed()
i2c: piix4: Replace hardcoded memory map size with a #define
i2c: piix4: Move port I/O region request/release code into functions
i2c: piix4: Move SMBus controller base address detect into function
i2c: piix4: Move SMBus port selection into function
i2c: piix4: Add EFCH MMIO support to region request and release
i2c: piix4: Add EFCH MMIO support to SMBus base address detect
i2c: piix4: Add EFCH MMIO support for SMBus port select
i2c: piix4: Enable EFCH MMIO for Family 17h+

 drivers/i2c/busses/i2c-piix4.c | 213 ++++++++++++++++++++++++++-------
 include/linux/ioport.h         |   2 +
 2 files changed, 169 insertions(+), 46 deletions(-)
Signature · 1 line
2.30.2
#1 lore raw

PATCH v5 1/9 kernel/resource: Introduce request_mem_region_muxed()

Support for requesting muxed memory region is implemented but not currently callable as a macro. Add the request muxed memory region macro.

MMIO memory accesses can be synchronized using request_mem_region() which is already available. This call will return failure if the resource is busy. The 'muxed' version of this macro will handle a busy resource by using a wait queue to retry until the resource is available.

---
 include/linux/ioport.h | 2 ++
 1 file changed, 2 insertions(+)
include/linux/ioport.h +2 -0
index 8359c50f9988..ec5f71f7135b 100644
@@ -262,6 +262,8 @@ resource_union(struct resource *r1, struct resource *r2, struct resource *r)
 #define request_muxed_region(start,n,name)	__request_region(&ioport_resource, (start), (n), (name), IORESOURCE_MUXED)
 #define __request_mem_region(start,n,name, excl) __request_region(&iomem_resource, (start), (n), (name), excl)
 #define request_mem_region(start,n,name) __request_region(&iomem_resource, (start), (n), (name), 0)
+#define request_mem_region_muxed(start, n, name) \
+	__request_region(&iomem_resource, (start), (n), (name), IORESOURCE_MUXED)
 #define request_mem_region_exclusive(start,n,name) \
 	__request_region(&iomem_resource, (start), (n), (name), IORESOURCE_EXCLUSIVE)
 #define rename_region(region, newname) do { (region)->name = (newname); } while (0)
Signature · 1 line
2.30.2
#2 lore raw

PATCH v5 2/9 i2c: piix4: Replace hardcoded memory map size with a #define

In reply to Terry Bowman

Replace number constant with #define to improve readability and maintainability.

---
 drivers/i2c/busses/i2c-piix4.c | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)
drivers/i2c/busses/i2c-piix4.c +10 -6
index 8c1b31ed0c42..3ff68967034e 100644
@@ -77,6 +77,7 @@
 
 /* SB800 constants */
 #define SB800_PIIX4_SMB_IDX		0xcd6
+#define SB800_PIIX4_SMB_MAP_SIZE	2
 
 #define KERNCZ_IMC_IDX			0x3e
 #define KERNCZ_IMC_DATA			0x3f
@@ -290,7 +291,8 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	else
 		smb_en = (aux) ? 0x28 : 0x2c;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, 2, "sb800_piix4_smb")) {
+	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
+				  "sb800_piix4_smb")) {
 		dev_err(&PIIX4_dev->dev,
 			"SMB base address index region 0x%x already in use.\n",
 			SB800_PIIX4_SMB_IDX);
@@ -302,7 +304,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
 	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
 
-	release_region(SB800_PIIX4_SMB_IDX, 2);
+	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
 
 	if (!smb_en) {
 		smb_en_status = smba_en_lo & 0x10;
@@ -371,7 +373,8 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		}
 	} else {
-		if (!request_muxed_region(SB800_PIIX4_SMB_IDX, 2,
+		if (!request_muxed_region(SB800_PIIX4_SMB_IDX,
+					  SB800_PIIX4_SMB_MAP_SIZE,
 					  "sb800_piix4_smb")) {
 			release_region(piix4_smba, SMBIOSIZE);
 			return -EBUSY;
@@ -384,7 +387,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 				       SB800_PIIX4_PORT_IDX;
 		piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
 		piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
-		release_region(SB800_PIIX4_SMB_IDX, 2);
+		release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
 	}
 
 	dev_info(&PIIX4_dev->dev,
@@ -682,7 +685,8 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 	u8 port;
 	int retval;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, 2, "sb800_piix4_smb"))
+	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
+				  "sb800_piix4_smb"))
 		return -EBUSY;
 
 	/* Request the SMBUS semaphore, avoid conflicts with the IMC */
@@ -758,7 +762,7 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		piix4_imc_wakeup();
 
 release:
-	release_region(SB800_PIIX4_SMB_IDX, 2);
+	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
 	return retval;
 }
 
Signature · 1 line
2.30.2
#3 lore raw

PATCH v5 3/9 i2c: piix4: Move port I/O region request/release code into functions

In reply to Terry Bowman

Move duplicated region request and release code into a function. Move is in preparation for following MMIO changes.

---
 drivers/i2c/busses/i2c-piix4.c | 48 ++++++++++++++++++++++------------
 1 file changed, 31 insertions(+), 17 deletions(-)
drivers/i2c/busses/i2c-piix4.c +31 -17
index 3ff68967034e..cc488b1e92c3 100644
@@ -165,6 +165,24 @@ struct i2c_piix4_adapdata {
 	u8 port;		/* Port number, shifted */
 };
 
+static int piix4_sb800_region_request(struct device *dev)
+{
+	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
+				  "sb800_piix4_smb")) {
+		dev_err(dev,
+			"SMBus base address index region 0x%x already in use.\n",
+			SB800_PIIX4_SMB_IDX);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void piix4_sb800_region_release(struct device *dev)
+{
+	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+}
+
 static int piix4_setup(struct pci_dev *PIIX4_dev,
 		       const struct pci_device_id *id)
 {
@@ -270,6 +288,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	unsigned short piix4_smba;
 	u8 smba_en_lo, smba_en_hi, smb_en, smb_en_status, port_sel;
 	u8 i2ccfg, i2ccfg_offset = 0x10;
+	int retval;
 
 	/* SB800 and later SMBus does not support forcing address */
 	if (force || force_addr) {
@@ -291,20 +310,16 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	else
 		smb_en = (aux) ? 0x28 : 0x2c;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
-				  "sb800_piix4_smb")) {
-		dev_err(&PIIX4_dev->dev,
-			"SMB base address index region 0x%x already in use.\n",
-			SB800_PIIX4_SMB_IDX);
-		return -EBUSY;
-	}
+	retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+	if (retval)
+		return retval;
 
 	outb_p(smb_en, SB800_PIIX4_SMB_IDX);
 	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
 	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
 	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
 
-	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+	piix4_sb800_region_release(&PIIX4_dev->dev);
 
 	if (!smb_en) {
 		smb_en_status = smba_en_lo & 0x10;
@@ -373,11 +388,10 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		}
 	} else {
-		if (!request_muxed_region(SB800_PIIX4_SMB_IDX,
-					  SB800_PIIX4_SMB_MAP_SIZE,
-					  "sb800_piix4_smb")) {
+		retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+		if (retval)
 			release_region(piix4_smba, SMBIOSIZE);
-			return -EBUSY;
+			return retval;
 		}
 
 		outb_p(SB800_PIIX4_PORT_IDX_SEL, SB800_PIIX4_SMB_IDX);
@@ -387,7 +401,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 				       SB800_PIIX4_PORT_IDX;
 		piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
 		piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
-		release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+		piix4_sb800_region_release(&PIIX4_dev->dev);
 	}
 
 	dev_info(&PIIX4_dev->dev,
@@ -685,9 +699,9 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 	u8 port;
 	int retval;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
-				  "sb800_piix4_smb"))
-		return -EBUSY;
+	retval = piix4_sb800_region_request(&adap->dev);
+	if (retval)
+		return retval;
 
 	/* Request the SMBUS semaphore, avoid conflicts with the IMC */
 	smbslvcnt  = inb_p(SMBSLVCNT);
@@ -762,7 +776,7 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		piix4_imc_wakeup();
 
 release:
-	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+	piix4_sb800_region_release(&adap->dev);
 	return retval;
 }
 
Signature · 1 line
2.30.2
#4 lore raw

Re: [PATCH v5 3/9] i2c: piix4: Move port I/O region request/release code into functions

Quoted 73 lines · Terry Bowman

Move duplicated region request and release code into a function. Move is in preparation for following MMIO changes.

---
 drivers/i2c/busses/i2c-piix4.c | 48 ++++++++++++++++++++++------------
 1 file changed, 31 insertions(+), 17 deletions(-)
drivers/i2c/busses/i2c-piix4.c +23 -8
index 3ff68967034e..cc488b1e92c3 100644
@@ -165,6 +165,24 @@ struct i2c_piix4_adapdata {
 	u8 port;		/* Port number, shifted */
 };
 
+static int piix4_sb800_region_request(struct device *dev)
+{
+	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
+				  "sb800_piix4_smb")) {
+		dev_err(dev,
+			"SMBus base address index region 0x%x already in use.\n",
+			SB800_PIIX4_SMB_IDX);
+		return -EBUSY;
+	}
+
+	return 0;
+}
+
+static void piix4_sb800_region_release(struct device *dev)
+{
+	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+}
+
 static int piix4_setup(struct pci_dev *PIIX4_dev,
 		       const struct pci_device_id *id)
 {
@@ -270,6 +288,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	unsigned short piix4_smba;
 	u8 smba_en_lo, smba_en_hi, smb_en, smb_en_status, port_sel;
 	u8 i2ccfg, i2ccfg_offset = 0x10;
+	int retval;
 
 	/* SB800 and later SMBus does not support forcing address */
 	if (force || force_addr) {
@@ -291,20 +310,16 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	else
 		smb_en = (aux) ? 0x28 : 0x2c;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
-				  "sb800_piix4_smb")) {
-		dev_err(&PIIX4_dev->dev,
-			"SMB base address index region 0x%x already in use.\n",
-			SB800_PIIX4_SMB_IDX);
-		return -EBUSY;
-	}
+	retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+	if (retval)
+		return retval;
 
 	outb_p(smb_en, SB800_PIIX4_SMB_IDX);
 	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
 	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
 	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
 
-	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+	piix4_sb800_region_release(&PIIX4_dev->dev);
 
 	if (!smb_en) {
 		smb_en_status = smba_en_lo & 0x10;

drivers/i2c/busses/i2c-piix4.c static int piix4_setup_sb800(struct pci_dev *PIIX4_dev, · line 392

Quoted 8 lines
drivers/i2c/busses/i2c-piix4.c +2 -3
@@ -373,11 +388,10 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		}
 	} else {
-		if (!request_muxed_region(SB800_PIIX4_SMB_IDX,
-					  SB800_PIIX4_SMB_MAP_SIZE,
-					  "sb800_piix4_smb")) {
+		retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+		if (retval)

Missing curly brace here, breaks the build.

Quoted 37 lines
drivers/i2c/busses/i2c-piix4.c +6 -6
 			release_region(piix4_smba, SMBIOSIZE);
-			return -EBUSY;
+			return retval;
 		}
 
 		outb_p(SB800_PIIX4_PORT_IDX_SEL, SB800_PIIX4_SMB_IDX);
@@ -387,7 +401,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 				       SB800_PIIX4_PORT_IDX;
 		piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
 		piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
-		release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+		piix4_sb800_region_release(&PIIX4_dev->dev);
 	}
 
 	dev_info(&PIIX4_dev->dev,
@@ -685,9 +699,9 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 	u8 port;
 	int retval;
 
-	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
-				  "sb800_piix4_smb"))
-		return -EBUSY;
+	retval = piix4_sb800_region_request(&adap->dev);
+	if (retval)
+		return retval;
 
 	/* Request the SMBUS semaphore, avoid conflicts with the IMC */
 	smbslvcnt  = inb_p(SMBSLVCNT);
@@ -762,7 +776,7 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		piix4_imc_wakeup();
 
 release:
-	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
+	piix4_sb800_region_release(&adap->dev);
 	return retval;
 }
 
Signature · 2 lines
Jean Delvare
SUSE L3 Support
#5 lore raw

Re: [PATCH v5 3/9] i2c: piix4: Move port I/O region request/release code into functions

Quoted 3 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+		if (retval)

Missing curly brace here, breaks the build.

Bummer, need to check why this wasn't found by my build-testing.

I fixed it up and also rebased patch 6 to my change. Terry, please have a look that I did everything correctly once I push out later today.

Thanks everyone!

#6 lore raw

Re: [PATCH v5 3/9] i2c: piix4: Move port I/O region request/release code into functions

Hi Wolfram and Jean,

Quoted 11 lines · Wolfram Sang
Quoted 3 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+		if (retval)

Missing curly brace here, breaks the build.

Bummer, need to check why this wasn't found by my build-testing.

I fixed it up and also rebased patch 6 to my change. Terry, please have a look that I did everything correctly once I push out later today.

Thanks everyone!

I need to look at how I sent that out. I will look for the fix in i2c/for-next. Thanks for the help and review.

#7 lore raw

Re: [PATCH v5 3/9] i2c: piix4: Move port I/O region request/release code into functions

Hi Wolfram an Jean,

Quoted 9 lines · Terry Bowman

Hi Wolfram and Jean,

Quoted 6 lines · Wolfram Sang
Quoted 3 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+		if (retval)

Missing curly brace here, breaks the build.

Bummer, need to check why this wasn't found by my build-testing.

Quoted 7 lines
Quoted 5 lines

I fixed it up and also rebased patch 6 to my change. Terry, please have a look that I did everything correctly once I push out later today.

Thanks everyone!

I need to look at how I sent that out. I will look for the fix in i2c/for-next. Thanks for the help and review.

I verified the fix looks good. From commit a3325d225b00 on i2c/for-next:

@@ -373,11 +388,10 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
}
} else {
- if (!request_muxed_region(SB800_PIIX4_SMB_IDX,
- SB800_PIIX4_SMB_MAP_SIZE,
- "sb800_piix4_smb")) {
+ retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+ if (retval) {
release_region(piix4_smba, SMBIOSIZE);
- return -EBUSY;
+ return retval;
}

#8 lore raw

Re: [PATCH v5 3/9] i2c: piix4: Move port I/O region request/release code into functions

In reply to Wolfram Sang
Quoted 5 lines · Wolfram Sang
Quoted 3 lines

Review

Quoted 1 line
(quoted diff) +1 -0
+		if (retval)  

Missing curly brace here, breaks the build.

Bummer, need to check why this wasn't found by my build-testing.

Maybe you build-tested the series as a whole but not individual patches? The series did build fine, as the missing curly brace was added back in a later patch.

Signature · 2 lines
Jean Delvare
SUSE L3 Support
#9 lore raw

Re: [PATCH v5 3/9] i2c: piix4: Move port I/O region request/release code into functions

Quoted 4 lines

Maybe you build-tested the series as a whole but not individual patches? The series did build fine, as the missing curly brace was added back in a later patch.

It wasn't that, but another gory detail. Updating my build tests is in the works. But thanks for the help!

#10 lore raw

PATCH v5 4/9 i2c: piix4: Move SMBus controller base address detect into function

In reply to Terry Bowman

Move SMBus controller base address detection into function. Refactor is in preparation for following MMIO changes.

---
 drivers/i2c/busses/i2c-piix4.c | 69 ++++++++++++++++++++++------------
 1 file changed, 44 insertions(+), 25 deletions(-)
drivers/i2c/busses/i2c-piix4.c +44 -25
index cc488b1e92c3..b7998eb44027 100644
@@ -282,11 +282,51 @@ static int piix4_setup(struct pci_dev *PIIX4_dev,
 	return piix4_smba;
 }
 
+static int piix4_setup_sb800_smba(struct pci_dev *PIIX4_dev,
+				  u8 smb_en,
+				  u8 aux,
+				  u8 *smb_en_status,
+				  unsigned short *piix4_smba)
+{
+	u8 smba_en_lo;
+	u8 smba_en_hi;
+	int retval;
+
+	retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+	if (retval)
+		return retval;
+
+	outb_p(smb_en, SB800_PIIX4_SMB_IDX);
+	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
+	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
+	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
+
+	piix4_sb800_region_release(&PIIX4_dev->dev);
+
+	if (!smb_en) {
+		*smb_en_status = smba_en_lo & 0x10;
+		*piix4_smba = smba_en_hi << 8;
+		if (aux)
+			*piix4_smba |= 0x20;
+	} else {
+		*smb_en_status = smba_en_lo & 0x01;
+		*piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
+	}
+
+	if (!*smb_en_status) {
+		dev_err(&PIIX4_dev->dev,
+			"SMBus Host Controller not enabled!\n");
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
 static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			     const struct pci_device_id *id, u8 aux)
 {
 	unsigned short piix4_smba;
-	u8 smba_en_lo, smba_en_hi, smb_en, smb_en_status, port_sel;
+	u8 smb_en, smb_en_status, port_sel;
 	u8 i2ccfg, i2ccfg_offset = 0x10;
 	int retval;
 
@@ -310,33 +350,12 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	else
 		smb_en = (aux) ? 0x28 : 0x2c;
 
-	retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+	retval = piix4_setup_sb800_smba(PIIX4_dev, smb_en, aux, &smb_en_status,
+					&piix4_smba);
+
 	if (retval)
 		return retval;
 
-	outb_p(smb_en, SB800_PIIX4_SMB_IDX);
-	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
-	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
-	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
-
-	piix4_sb800_region_release(&PIIX4_dev->dev);
-
-	if (!smb_en) {
-		smb_en_status = smba_en_lo & 0x10;
-		piix4_smba = smba_en_hi << 8;
-		if (aux)
-			piix4_smba |= 0x20;
-	} else {
-		smb_en_status = smba_en_lo & 0x01;
-		piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
-	}
-
-	if (!smb_en_status) {
-		dev_err(&PIIX4_dev->dev,
-			"SMBus Host Controller not enabled!\n");
-		return -ENODEV;
-	}
-
 	if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
 		return -ENODEV;
 
Signature · 1 line
2.30.2
#11 lore raw

PATCH v5 5/9 i2c: piix4: Move SMBus port selection into function

In reply to Terry Bowman

Move port selection code into a separate function. Refactor is in preparation for following MMIO changes.

---
 drivers/i2c/busses/i2c-piix4.c | 27 +++++++++++++++++----------
 1 file changed, 17 insertions(+), 10 deletions(-)
drivers/i2c/busses/i2c-piix4.c +17 -10
index b7998eb44027..f4a262a7d199 100644
@@ -698,6 +698,20 @@ static void piix4_imc_wakeup(void)
 	release_region(KERNCZ_IMC_IDX, 2);
 }
 
+static int piix4_sb800_port_sel(u8 port)
+{
+	u8 smba_en_lo, val;
+
+	outb_p(piix4_port_sel_sb800, SB800_PIIX4_SMB_IDX);
+	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
+
+	val = (smba_en_lo & ~piix4_port_mask_sb800) | port;
+	if (smba_en_lo != val)
+		outb_p(val, SB800_PIIX4_SMB_IDX + 1);
+
+	return (smba_en_lo & piix4_port_mask_sb800);
+}
+
 /*
  * Handles access to multiple SMBus ports on the SB800.
  * The port is selected by bits 2:1 of the smb_en register (0x2c).
@@ -714,8 +728,7 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 	unsigned short piix4_smba = adapdata->smba;
 	int retries = MAX_TIMEOUT;
 	int smbslvcnt;
-	u8 smba_en_lo;
-	u8 port;
+	u8 prev_port;
 	int retval;
 
 	retval = piix4_sb800_region_request(&adap->dev);
@@ -775,18 +788,12 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		}
 	}
 
-	outb_p(piix4_port_sel_sb800, SB800_PIIX4_SMB_IDX);
-	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
-
-	port = adapdata->port;
-	if ((smba_en_lo & piix4_port_mask_sb800) != port)
-		outb_p((smba_en_lo & ~piix4_port_mask_sb800) | port,
-		       SB800_PIIX4_SMB_IDX + 1);
+	prev_port = piix4_sb800_port_sel(adapdata->port);
 
 	retval = piix4_access(adap, addr, flags, read_write,
 			      command, size, data);
 
-	outb_p(smba_en_lo, SB800_PIIX4_SMB_IDX + 1);
+	piix4_sb800_port_sel(prev_port);
 
 	/* Release the semaphore */
 	outb_p(smbslvcnt | 0x20, SMBSLVCNT);
Signature · 1 line
2.30.2
#12 lore raw

PATCH v5 6/9 i2c: piix4: Add EFCH MMIO support to region request and release

In reply to Terry Bowman

EFCH cd6h/cd7h port I/O may no longer be available on later AMD processors and it is recommended to use MMIO instead. Update the request and release functions to support MMIO.

MMIO request/release and mmapping require details during cleanup. Add a MMIO configuration structure containing resource and vaddress details for mapping the region, accessing the region, and releasing the region.

---
 drivers/i2c/busses/i2c-piix4.c | 68 +++++++++++++++++++++++++++++-----
 1 file changed, 59 insertions(+), 9 deletions(-)
drivers/i2c/busses/i2c-piix4.c +59 -9
index f4a262a7d199..d06998f7b031 100644
@@ -98,6 +98,9 @@
 #define SB800_PIIX4_PORT_IDX_MASK_KERNCZ	0x18
 #define SB800_PIIX4_PORT_IDX_SHIFT_KERNCZ	3
 
+#define SB800_PIIX4_FCH_PM_ADDR			0xFED80300
+#define SB800_PIIX4_FCH_PM_SIZE			8
+
 /* insmod parameters */
 
 /* If force is set to anything different from 0, we forcibly enable the
@@ -156,6 +159,12 @@ static const char *piix4_main_port_names_sb800[PIIX4_MAX_ADAPTERS] = {
 };
 static const char *piix4_aux_port_name_sb800 = " port 1";
 
+struct sb800_mmio_cfg {
+	void __iomem *addr;
+	struct resource *res;
+	bool use_mmio;
+};
+
 struct i2c_piix4_adapdata {
 	unsigned short smba;
 
@@ -163,10 +172,40 @@ struct i2c_piix4_adapdata {
 	bool sb800_main;
 	bool notify_imc;
 	u8 port;		/* Port number, shifted */
+	struct sb800_mmio_cfg mmio_cfg;
 };
 
-static int piix4_sb800_region_request(struct device *dev)
+static int piix4_sb800_region_request(struct device *dev,
+				      struct sb800_mmio_cfg *mmio_cfg)
 {
+	if (mmio_cfg->use_mmio) {
+		struct resource *res;
+		void __iomem *addr;
+
+		res = request_mem_region_muxed(SB800_PIIX4_FCH_PM_ADDR,
+					       SB800_PIIX4_FCH_PM_SIZE,
+					       "sb800_piix4_smb");
+		if (!res) {
+			dev_err(dev,
+				"SMBus base address memory region 0x%x already in use.\n",
+				SB800_PIIX4_FCH_PM_ADDR);
+			return -EBUSY;
+		}
+
+		addr = ioremap(SB800_PIIX4_FCH_PM_ADDR,
+			       SB800_PIIX4_FCH_PM_SIZE);
+		if (!addr) {
+			release_resource(res);
+			dev_err(dev, "SMBus base address mapping failed.\n");
+			return -ENOMEM;
+		}
+
+		mmio_cfg->res = res;
+		mmio_cfg->addr = addr;
+
+		return 0;
+	}
+
 	if (!request_muxed_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE,
 				  "sb800_piix4_smb")) {
 		dev_err(dev,
@@ -178,8 +217,15 @@ static int piix4_sb800_region_request(struct device *dev)
 	return 0;
 }
 
-static void piix4_sb800_region_release(struct device *dev)
+static void piix4_sb800_region_release(struct device *dev,
+				       struct sb800_mmio_cfg *mmio_cfg)
 {
+	if (mmio_cfg->use_mmio) {
+		iounmap(mmio_cfg->addr);
+		release_resource(mmio_cfg->res);
+		return;
+	}
+
 	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
 }
 
@@ -288,11 +334,13 @@ static int piix4_setup_sb800_smba(struct pci_dev *PIIX4_dev,
 				  u8 *smb_en_status,
 				  unsigned short *piix4_smba)
 {
+	struct sb800_mmio_cfg mmio_cfg;
 	u8 smba_en_lo;
 	u8 smba_en_hi;
 	int retval;
 
-	retval = piix4_sb800_region_request(&PIIX4_dev->dev);
+	mmio_cfg.use_mmio = 0;
+	retval = piix4_sb800_region_request(&PIIX4_dev->dev, &mmio_cfg);
 	if (retval)
 		return retval;
 
@@ -301,7 +349,7 @@ static int piix4_setup_sb800_smba(struct pci_dev *PIIX4_dev,
 	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
 	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
 
-	piix4_sb800_region_release(&PIIX4_dev->dev);
+	piix4_sb800_region_release(&PIIX4_dev->dev, &mmio_cfg);
 
 	if (!smb_en) {
 		*smb_en_status = smba_en_lo & 0x10;
@@ -328,6 +376,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 	unsigned short piix4_smba;
 	u8 smb_en, smb_en_status, port_sel;
 	u8 i2ccfg, i2ccfg_offset = 0x10;
+	struct sb800_mmio_cfg mmio_cfg;
 	int retval;
 
 	/* SB800 and later SMBus does not support forcing address */
@@ -407,8 +456,9 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		}
 	} else {
-		retval = piix4_sb800_region_request(&PIIX4_dev->dev);
-		if (retval)
+		mmio_cfg.use_mmio = 0;
+		retval = piix4_sb800_region_request(&PIIX4_dev->dev, &mmio_cfg);
+		if (retval) {
 			release_region(piix4_smba, SMBIOSIZE);
 			return retval;
 		}
@@ -420,7 +470,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 				       SB800_PIIX4_PORT_IDX;
 		piix4_port_mask_sb800 = SB800_PIIX4_PORT_IDX_MASK;
 		piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
-		piix4_sb800_region_release(&PIIX4_dev->dev);
+		piix4_sb800_region_release(&PIIX4_dev->dev, &mmio_cfg);
 	}
 
 	dev_info(&PIIX4_dev->dev,
@@ -731,7 +781,7 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 	u8 prev_port;
 	int retval;
 
-	retval = piix4_sb800_region_request(&adap->dev);
+	retval = piix4_sb800_region_request(&adap->dev, &adapdata->mmio_cfg);
 	if (retval)
 		return retval;
 
@@ -802,7 +852,7 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		piix4_imc_wakeup();
 
 release:
-	piix4_sb800_region_release(&adap->dev);
+	piix4_sb800_region_release(&adap->dev, &adapdata->mmio_cfg);
 	return retval;
 }
 
Signature · 1 line
2.30.2
#13 lore raw

PATCH v5 7/9 i2c: piix4: Add EFCH MMIO support to SMBus base address detect

In reply to Terry Bowman

The EFCH SMBus controller's base address is determined using details in FCH::PM::DECODEEN[smbusasfiobase] and FCH::PM::DECODEEN[smbusasfioen].These register fields were accessed using cd6h/cd7h port I/O. cd6h/cd7h port I/O is no longer available in later AMD processors. Change base address detection to use MMIO instead of port I/O cd6h/cd7h.

---
 drivers/i2c/busses/i2c-piix4.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)
drivers/i2c/busses/i2c-piix4.c +9 -4
index d06998f7b031..7f312177eb27 100644
@@ -344,10 +344,15 @@ static int piix4_setup_sb800_smba(struct pci_dev *PIIX4_dev,
 	if (retval)
 		return retval;
 
-	outb_p(smb_en, SB800_PIIX4_SMB_IDX);
-	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
-	outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
-	smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
+	if (mmio_cfg.use_mmio) {
+		smba_en_lo = ioread8(mmio_cfg.addr);
+		smba_en_hi = ioread8(mmio_cfg.addr + 1);
+	} else {
+		outb_p(smb_en, SB800_PIIX4_SMB_IDX);
+		smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
+		outb_p(smb_en + 1, SB800_PIIX4_SMB_IDX);
+		smba_en_hi = inb_p(SB800_PIIX4_SMB_IDX + 1);
+	}
 
 	piix4_sb800_region_release(&PIIX4_dev->dev, &mmio_cfg);
 
Signature · 1 line
2.30.2
#14 lore raw

PATCH v5 8/9 i2c: piix4: Add EFCH MMIO support for SMBus port select

In reply to Terry Bowman

AMD processors include registers capable of selecting between 2 SMBus ports. Port selection is made during each user access by writing to FCH::PM::DECODEEN[smbus0sel]. Change the driver to use MMIO during SMBus port selection because cd6h/cd7h port I/O is not available on later AMD processors.

---
 drivers/i2c/busses/i2c-piix4.c | 15 ++++++++++++---
 1 file changed, 12 insertions(+), 3 deletions(-)
drivers/i2c/busses/i2c-piix4.c +12 -3
index 7f312177eb27..4789fc9ad270 100644
@@ -753,10 +753,19 @@ static void piix4_imc_wakeup(void)
 	release_region(KERNCZ_IMC_IDX, 2);
 }
 
-static int piix4_sb800_port_sel(u8 port)
+static int piix4_sb800_port_sel(u8 port, struct sb800_mmio_cfg *mmio_cfg)
 {
 	u8 smba_en_lo, val;
 
+	if (mmio_cfg->use_mmio) {
+		smba_en_lo = ioread8(mmio_cfg->addr + piix4_port_sel_sb800);
+		val = (smba_en_lo & ~piix4_port_mask_sb800) | port;
+		if (smba_en_lo != val)
+			iowrite8(val, mmio_cfg->addr + piix4_port_sel_sb800);
+
+		return (smba_en_lo & piix4_port_mask_sb800);
+	}
+
 	outb_p(piix4_port_sel_sb800, SB800_PIIX4_SMB_IDX);
 	smba_en_lo = inb_p(SB800_PIIX4_SMB_IDX + 1);
 
@@ -843,12 +852,12 @@ static s32 piix4_access_sb800(struct i2c_adapter *adap, u16 addr,
 		}
 	}
 
-	prev_port = piix4_sb800_port_sel(adapdata->port);
+	prev_port = piix4_sb800_port_sel(adapdata->port, &adapdata->mmio_cfg);
 
 	retval = piix4_access(adap, addr, flags, read_write,
 			      command, size, data);
 
-	piix4_sb800_port_sel(prev_port);
+	piix4_sb800_port_sel(prev_port, &adapdata->mmio_cfg);
 
 	/* Release the semaphore */
 	outb_p(smbslvcnt | 0x20, SMBSLVCNT);
Signature · 1 line
2.30.2
#15 lore raw

PATCH v5 9/9 i2c: piix4: Enable EFCH MMIO for Family 17h+

In reply to Terry Bowman

Enable EFCH MMIO using check for SMBus PCI revision ID value 0x51 or greater. This PCI revision ID check will enable family 17h and future AMD processors with the same EFCH SMBus controller HW.

---
 drivers/i2c/busses/i2c-piix4.c | 17 +++++++++++++++--
 1 file changed, 15 insertions(+), 2 deletions(-)
drivers/i2c/busses/i2c-piix4.c +15 -2
index 4789fc9ad270..ac8e7d60672a 100644
@@ -229,6 +229,18 @@ static void piix4_sb800_region_release(struct device *dev,
 	release_region(SB800_PIIX4_SMB_IDX, SB800_PIIX4_SMB_MAP_SIZE);
 }
 
+static bool piix4_sb800_use_mmio(struct pci_dev *PIIX4_dev)
+{
+	/*
+	 * cd6h/cd7h port I/O accesses can be disabled on AMD processors
+	 * w/ SMBus PCI revision ID 0x51 or greater. MMIO is supported on
+	 * the same processors and is the recommended access method.
+	 */
+	return (PIIX4_dev->vendor == PCI_VENDOR_ID_AMD &&
+		PIIX4_dev->device == PCI_DEVICE_ID_AMD_KERNCZ_SMBUS &&
+		PIIX4_dev->revision >= 0x51);
+}
+
 static int piix4_setup(struct pci_dev *PIIX4_dev,
 		       const struct pci_device_id *id)
 {
@@ -339,7 +351,7 @@ static int piix4_setup_sb800_smba(struct pci_dev *PIIX4_dev,
 	u8 smba_en_hi;
 	int retval;
 
-	mmio_cfg.use_mmio = 0;
+	mmio_cfg.use_mmio = piix4_sb800_use_mmio(PIIX4_dev);
 	retval = piix4_sb800_region_request(&PIIX4_dev->dev, &mmio_cfg);
 	if (retval)
 		return retval;
@@ -461,7 +473,7 @@ static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
 			piix4_port_shift_sb800 = SB800_PIIX4_PORT_IDX_SHIFT;
 		}
 	} else {
-		mmio_cfg.use_mmio = 0;
+		mmio_cfg.use_mmio = piix4_sb800_use_mmio(PIIX4_dev);
 		retval = piix4_sb800_region_request(&PIIX4_dev->dev, &mmio_cfg);
 		if (retval) {
 			release_region(piix4_smba, SMBIOSIZE);
@@ -944,6 +956,7 @@ static int piix4_add_adapter(struct pci_dev *dev, unsigned short smba,
 		return -ENOMEM;
 	}
 
+	adapdata->mmio_cfg.use_mmio = piix4_sb800_use_mmio(dev);
 	adapdata->smba = smba;
 	adapdata->sb800_main = sb800_main;
 	adapdata->port = port << piix4_port_shift_sb800;
Signature · 1 line
2.30.2
#16 lore raw
In reply to Terry Bowman
Quoted 136 lines · Terry Bowman

This series changes the piix4_smbus driver's cd6h/cd7h port I/O accesses to use MMIO instead. This is necessary because cd6h/cd7h port I/O may be disabled on later AMD processors.

This series includes patches with MMIO accesses to register FCH::PM::DECODEEN. The same register is also accessed by the sp5100_tco driver.[1] Synchronization to the MMIO register is required in both drivers.

The first patch creates a macro to request MMIO region using the 'muxed' retry logic. This is used in patch 6 to synchronize accesses to EFCH MMIO.

The second patch replaces a hardcoded region size with a #define. This is to improve maintainability and was requested from v2 review.

The third patch moves duplicated region request/release code into functions. This locates related code into functions and reduces code line count. This will also make adding MMIO support in patch 6 easier.

The fourth patch moves SMBus controller address detection into a function. This is in preparation for adding MMIO region support.

The fifth patch moves EFCH port selection into a function. This is in preparation for adding MMIO region support.

The sixth patch adds MMIO support for region requesting/releasing and mapping. This is necessary for using MMIO to detect SMBus controller address, enable SMBbus controller region, and control the port select.

The seventh patch updates the SMBus controller address detection to support using MMIO. This is necessary because the driver accesses register FCH::PM::DECODEEN during initialization and only available using MMIO on later AMD processors.

The eighth patch updates the SMBus port selection to support MMIO. This is required because port selection control resides in the FCH::PM::DECODEEN[smbus0sel] and is only accessible using MMIO on later AMD processors.

The ninth patch enables the EFCH MMIO functionality added earlier in this series. The SMBus controller's PCI revision ID is used to check if EFCH MMIO is supported by HW and should be enabled in the driver.

Based on v5.17-rc2.

Testing:
Tested on family 19h using:
i2cdetect -y 0
i2cdetect -y 2

- Results using v5.16 and this pachset applied. Below

    shows the devices detected on the busses:
    
    # i2cdetect -y 0 
         0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
    00:                         -- -- -- -- -- -- -- -- 
    10: 10 11 -- -- -- -- -- -- 18 -- -- -- -- -- -- -- 
    20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    30: 30 -- -- -- -- 35 36 -- -- -- -- -- -- -- -- -- 
    40: -- -- -- -- -- -- -- -- -- -- 4a -- -- -- -- -- 
    50: 50 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    70: -- -- -- 73 -- -- -- --                         
    # i2cdetect -y 2
         0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
    00:                         -- -- -- -- -- -- -- -- 
    10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    30: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
    40: -- -- -- -- -- -- -- -- -- -- -- -- 4c -- -- -- 
    50: -- 51 -- -- 54 -- -- -- -- -- -- -- -- -- -- -- 
    60: 60 -- -- 63 -- -- 66 -- -- -- -- 6b -- -- 6e -- 
    70: 70 71 72 73 74 75 -- 77

Also tested using sp5100_tco submitted series listed below.[1] I applied the sp5100_tco v4 series and ran:
cat >> /dev/watchdog

[1] sp5100_tco v4 patchset can be found here:

Changes in v5:
- Use request/release helper function for sb800 device in piix4_setup_sb800(). Patch 3. (Jean Delvare)
- Revert 'piix4_smba' variable definition ordering back as it was in piix4_setup_sb800(). Patch 4. (Jean Delvare)
- Add newline after piix4_sb800_port_sel(). Patch 5. (Jean Delvare)
- Remove unnecessary initialization in piix4_add_adapter(). Patch 6. (Jean Delvare)
- Remove unnecessary #define AMD_PCI_SMBUS_REVISION_MMIO. Patch 9. (Jean Delvare)
- Add description for 0x51 constant moved in the above item. This is in piix4_sb800_use_mmio(). Patch 9. (Andy Shevchenko)
- Rebase to v5.17-rc2. (Andy Shevchenko)
- Update patch 9 description. (Terry Bowman)

Changes in v4:
- Changed request_muxed_mem_region() macro to request_mem_region_muxed() in patch 1. (Andy Shevchenko)
- Removed unnecessary newline where possible in calls to request_muxed_region() in patch 2. (Terry Bowman)
- Changed piix4_sb800_region_setup() to piix4_sb800_region_request(). Patch 3. (Jean Delvare)
- Reordered piix4_setup_sb800() local variables from longest name length to shortest name length. Patch 4. (Terry Bowman)
- Changed piix4_sb800_region_request() and piix4_sb800_region_release() by adding early return() to remove 'else' improving readability. Patch 6. (Terry Bowman)
- Removed iowrite32(ioread32(...), ...). Unnecessary because MMIO is already enabled. (Terry Bowman)
- Refactored piix4_sb800_port_sel() to simplify the 'if' statement using temp variable. Patch 8. (Terry Bowman)
- Added mmio_cfg.use_mmio assignment in piix4_add_adapter(). This is needed for calls to piix4_sb800_port_sel() after initialization during normal operation. Patch 9. (Terry Bowman)

Changes in v3:
- Added request_muxed_mem_region() patch (Wolfram, Guenter)
- Reduced To/Cc list length. (Andy)

Changes in v2:
- Split single patch. (Jean Delvare)
- Replace constant 2 with SB800_PIIX4_SMB_MAP_SIZE where appropriate. (Jean Delvare)
- Shorten SB800_PIIX4_FCH_PM_DECODEEN_MMIO_EN name length to SB800_PIIX4_FCH_PM_DECODEEN_MMIO. (Jean Delvare)
- Change AMD_PCI_SMBUS_REVISION_MMIO from 0x59 to 0x51. (Terry Bowman)
- Change piix4_sb800_region_setup() to piix4_sb800_region_request(). (Jean Delvare)
- Change 'SMB' text in logging to 'SMBus' (Jean Delvare)
- Remove unnecessary NULL assignment in piix4_sb800_region_release(). (Jean Delvare)
- Move 'u8' variable definitions to single line. (Jean Delvare)
- Hardcode piix4_setup_sb800_smba() return value to 0 since it is always
0. (Jean Delvare)

Quoted 11 lines

Terry Bowman (9):
kernel/resource: Introduce request_mem_region_muxed()
i2c: piix4: Replace hardcoded memory map size with a #define
i2c: piix4: Move port I/O region request/release code into functions
i2c: piix4: Move SMBus controller base address detect into function
i2c: piix4: Move SMBus port selection into function
i2c: piix4: Add EFCH MMIO support to region request and release
i2c: piix4: Add EFCH MMIO support to SMBus base address detect
i2c: piix4: Add EFCH MMIO support for SMBus port select
i2c: piix4: Enable EFCH MMIO for Family 17h+

Applied the series to for-next, thank you Terry for keeping at it and Jean and Andy for the review. I'll send the pull request containing the ioport update to the WDT maintainers now. All further changes should be based on top of this now.

Reviewed-by Tested-by on the v5 series
#17 lore raw
In reply to Terry Bowman
Quoted 9 lines · Terry Bowman

This series changes the piix4_smbus driver's cd6h/cd7h port I/O accesses to use MMIO instead. This is necessary because cd6h/cd7h port I/O may be disabled on later AMD processors.

This series includes patches with MMIO accesses to register FCH::PM::DECODEEN. The same register is also accessed by the sp5100_tco driver.[1] Synchronization to the MMIO register is required in both drivers.
(...)

Except for the curly brace issue in patch 3, all looks good, so I confirm my

on all i2c-piix4 patches.

Thanks,

Signature · 2 lines
Jean Delvare
SUSE L3 Support