Skip to contentSkip to conversation

arm64: dts: Add i.MX8DXL initial support

PATCH Superseded Abel Vesa 2 participants 11 messages Apr 4, 2022 – Apr 13, 2022

Subsystems (4)

v5 of 9 Superseded Latest is v9 →

lore
Share & tools
lore

Abel Vesa

author
#0 lore raw

v5 cover arm64: dts: Add i.MX8DXL initial support

Here is the v4:
https://lore.kernel.org/linux-arm-kernel/[email protected]/raw

Abel Vesa (3):
arm64: dts: freescale: Add adma subsystem dtsi for imx8dxl
dt-bindings: fsl: scu: Add i.MX8DXL ocotp binding
dt-bindings: net: dwmac-imx: Document clk_csr property

Jacky Bai (5):
arm64: dts: freescale: Add the top level dtsi support for imx8dxl
arm64: dts: freescale: Add the imx8dxl connectivity subsys dtsi
arm64: dts: freescale: Add ddr subsys dtsi for imx8dxl
arm64: dts: freescale: Add lsio subsys dtsi for imx8dxl
arm64: dts: freescale: Add i.MX8DXL evk board support

 .../bindings/arm/freescale/fsl,scu.txt        |   3 +-
 .../bindings/net/nxp,dwmac-imx.yaml           |   4 +
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 266 ++++++++++++++++++
 .../boot/dts/freescale/imx8dxl-ss-adma.dtsi   |  52 ++++
 .../boot/dts/freescale/imx8dxl-ss-conn.dtsi   | 135 +++++++++
 .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi    |  36 +++
 .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi   |  78 +++++
 arch/arm64/boot/dts/freescale/imx8dxl.dtsi    | 247 ++++++++++++++++
 9 files changed, 821 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi

--
2.34.1

author
#1 lore raw

PATCH v5 1/8 arm64: dts: freescale: Add the top level dtsi support for imx8dxl

From: Jacky Bai <[email protected]>

The i.MX8DXL is a device targeting the automotive and industrial market segments. The flexibility of the architecture allows for use in a wide variety of general embedded applications. The chip is designed to achieve both high performance and low power consumption. The chip relies on the power efficient dual (2x) Cortex-A35 cluster.

Add the reserved memory node property for dsp reserved memory, the wakeup-irq property for SCU node, the rpmsg and the cm4 rproc support.

---
 arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 247 +++++++++++++++++++++
 1 file changed, 247 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi
arch/arm64/boot/dts/freescale/imx8dxl.dtsi new file +247 -0
new file mode 100644
index 000000000000..17a33e54d992
@@ -0,0 +1,247 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019-2021 NXP
+ */
+
+#include <dt-bindings/clock/imx8-clock.h>
+#include <dt-bindings/firmware/imx/rsrc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/pads-imx8dxl.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &eqos;
+		gpio0 = &lsio_gpio0;
+		gpio1 = &lsio_gpio1;
+		gpio2 = &lsio_gpio2;
+		gpio3 = &lsio_gpio3;
+		gpio4 = &lsio_gpio4;
+		gpio5 = &lsio_gpio5;
+		gpio6 = &lsio_gpio6;
+		gpio7 = &lsio_gpio7;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mu1 = &lsio_mu1;
+		serial0 = &lpuart0;
+		serial1 = &lpuart1;
+		serial2 = &lpuart2;
+		serial3 = &lpuart3;
+	};
+
+	cpus: cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		/* We have 1 cluster with 2 Cortex-A35 cores */
+		A35_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	a35_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_reserved: dsp@92400000 {
+			reg = <0 0x92400000 0 0x2000000>;
+			no-map;
+		};
+	};
+
+	gic: interrupt-controller@51a00000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */
+		      <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	scu {
+		compatible = "fsl,imx-scu";
+		mbox-names = "tx0",
+			     "rx0",
+			     "gip3";
+		mboxes = <&lsio_mu1 0 0
+			  &lsio_mu1 1 0
+			  &lsio_mu1 3 3>;
+
+		pd: imx8dxl-pd {
+			compatible = "fsl,imx8dxl-scu-pd", "fsl,scu-pd";
+			#power-domain-cells = <1>;
+		};
+
+		clk: clock-controller {
+			compatible = "fsl,imx8dxl-clk", "fsl,scu-clk";
+			#clock-cells = <2>;
+			clocks = <&xtal32k &xtal24m>;
+			clock-names = "xtal_32KHz", "xtal_24Mhz";
+		};
+
+		iomuxc: pinctrl {
+			compatible = "fsl,imx8dxl-iomuxc";
+		};
+
+		ocotp: imx8qx-ocotp {
+			compatible = "fsl,imx8dxl-scu-ocotp", "fsl,imx8qxp-scu-ocotp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			fec_mac0: mac@2c4 {
+				reg = <0x2c4 6>;
+			};
+
+			fec_mac1: mac@2c6 {
+				reg = <0x2c6 6>;
+			};
+		};
+
+		watchdog {
+			compatible = "fsl,imx-sc-wdt";
+			timeout-sec = <60>;
+		};
+
+		tsens: thermal-sensor {
+			compatible = "fsl,imx-sc-thermal";
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
+	};
+
+	thermal_zones: thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <107000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <127000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	clk_dummy: clock-dummy {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+		clock-output-names = "clk_dummy";
+	};
+
+	xtal32k: clock-xtal32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32KHz";
+	};
+
+	xtal24m: clock-xtal24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal_24MHz";
+	};
+
+	sc_pwrkey: sc-powerkey {
+		compatible = "fsl,imx8-pwrkey";
+		linux,keycode = <KEY_POWER>;
+		wakeup-source;
+	};
+
+	/* sorted in register address */
+	#include "imx8-ss-adma.dtsi"
+	#include "imx8-ss-conn.dtsi"
+	#include "imx8-ss-ddr.dtsi"
+	#include "imx8-ss-lsio.dtsi"
+};
+
+#include "imx8dxl-ss-adma.dtsi"
+#include "imx8dxl-ss-conn.dtsi"
+#include "imx8dxl-ss-lsio.dtsi"
+#include "imx8dxl-ss-ddr.dtsi"
Signature · 1 line
2.34.1
author
#2 lore raw

PATCH v5 2/8 arm64: dts: freescale: Add adma subsystem dtsi for imx8dxl

In reply to Abel Vesa

Override the I2Cs, LPUARTs, audio_ipg_clk and dma_ipg_clk with the i.MX8DXL specific properties.

---
 .../boot/dts/freescale/imx8dxl-ss-adma.dtsi   | 52 +++++++++++++++++++
 1 file changed, 52 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi new file +52 -0
new file mode 100644
index 000000000000..4d0c75bad74c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019-2021 NXP
+ */
+
+&audio_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&dma_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&i2c0 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c2 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c3 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart0 {
+	compatible = "fsl,imx8dxl-lpuart", "fsl,imx8qxp-lpuart";
+	interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart1 {
+	compatible = "fsl,imx8dxl-lpuart", "fsl,imx8qxp-lpuart";
+	interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart2 {
+	compatible = "fsl,imx8dxl-lpuart", "fsl,imx8qxp-lpuart";
+	interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart3 {
+	compatible = "fsl,imx8dxl-lpuart", "fsl,imx8qxp-lpuart";
+	interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+};
Signature · 1 line
2.34.1
author
#3 lore raw

PATCH v5 3/8 arm64: dts: freescale: Add the imx8dxl connectivity subsys dtsi

In reply to Abel Vesa

From: Jacky Bai <[email protected]>

On i.MX8DXL, the Connectivity subsystem includes below peripherals:
1x ENET with AVB support, 1x ENET with TSN support, 2x USB OTG, 1x eMMC, 2x SD, 1x NAND.

---
 .../boot/dts/freescale/imx8dxl-ss-conn.dtsi   | 135 ++++++++++++++++++
 1 file changed, 135 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi new file +135 -0
new file mode 100644
index 000000000000..8dcf8c9056a4
@@ -0,0 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019-2021 NXP
+ */
+
+/delete-node/ &enet1_lpcg;
+/delete-node/ &fec2;
+
+&conn_subsys {
+	conn_enet0_root_clk: clock-conn-enet0-root {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <250000000>;
+		clock-output-names = "conn_enet0_root_clk";
+	};
+
+	eqos: ethernet@5b050000 {
+		compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a";
+		reg = <0x5b050000 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "eth_wake_irq", "macirq";
+		clocks = <&eqos_lpcg IMX_LPCG_CLK_2>,
+			 <&eqos_lpcg IMX_LPCG_CLK_4>,
+			 <&eqos_lpcg IMX_LPCG_CLK_0>,
+			 <&eqos_lpcg IMX_LPCG_CLK_3>,
+			 <&eqos_lpcg IMX_LPCG_CLK_1>;
+		clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem";
+		assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <125000000>;
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+		clk_csr = <0>;
+		status = "disabled";
+	};
+
+	usbotg2: usb@5b0e0000 {
+		compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb";
+		reg = <0x5b0e0000 0x200>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+		fsl,usbphy = <&usbphy2>;
+		fsl,usbmisc = <&usbmisc2 0>;
+		/*
+		 * usbotg1 and usbotg2 share one clock
+		 * scfw disable clock access and keep it always on
+		 * in case other core (M4) use one of these.
+		 */
+		clocks = <&clk_dummy>;
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>;
+		rx-burst-size-dword = <0x10>;
+		#stream-id-cells = <1>;
+		power-domains = <&pd IMX_SC_R_USB_1>;
+		status = "disabled";
+	};
+
+	usbmisc2: usbmisc@5b0e0200 {
+		#index-cells = <1>;
+		compatible = "fsl,imx8dxl-usbmisc", "fsl,imx7ulp-usbmisc";
+		reg = <0x5b0e0200 0x200>;
+	};
+
+	usbphy2: usbphy@0x5b110000 {
+		compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy";
+		reg = <0x5b110000 0x1000>;
+		clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>;
+		status = "disabled";
+	};
+
+	eqos_lpcg: clock-controller@5b240000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b240000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&conn_enet0_root_clk>,
+			 <&conn_axi_clk>,
+			 <&conn_axi_clk>,
+			 <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
+			 <&conn_ipg_clk>;
+		clock-indices = <IMX_LPCG_CLK_0>,
+				<IMX_LPCG_CLK_2>,
+				<IMX_LPCG_CLK_4>,
+				<IMX_LPCG_CLK_5>,
+				<IMX_LPCG_CLK_6>;
+		clock-output-names = "eqos_ptp",
+				     "eqos_mem_clk",
+				     "eqos_aclk",
+				     "eqos_clk",
+				     "eqos_csr_clk";
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+	};
+
+	usb2_2_lpcg: clock-controller@5b280000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b280000 0x10000>;
+		#clock-cells = <1>;
+		clock-indices = <IMX_LPCG_CLK_7>;
+		clocks = <&conn_ipg_clk>;
+		clock-output-names = "usboh3_2_phy_ipg_clk";
+	};
+};
+
+&enet0_lpcg {
+	clocks = <&conn_enet0_root_clk>,
+		 <&conn_enet0_root_clk>,
+		 <&conn_axi_clk>,
+		 <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>,
+		 <&conn_ipg_clk>,
+		 <&conn_ipg_clk>;
+};
+
+&fec1 {
+	compatible = "fsl,imx8dxl-fec", "fsl,imx8qm-fec";
+	interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+	assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>;
+	assigned-clock-rates = <125000000>;
+};
+
+&usdhc1 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc2 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc3 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+};
Signature · 1 line
2.34.1
author
#4 lore raw

PATCH v5 4/8 arm64: dts: freescale: Add ddr subsys dtsi for imx8dxl

In reply to Abel Vesa

From: Jacky Bai <[email protected]>

Add the ddr subsys dtsi for i.MX8DXL. Additional db pmu is added compared to i.MX8QXP.

---
 .../boot/dts/freescale/imx8dxl-ss-ddr.dtsi    | 36 +++++++++++++++++++
 1 file changed, 36 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi new file +36 -0
new file mode 100644
index 000000000000..75b482966d94
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ */
+
+&ddr_subsys {
+	db_ipg_clk: clock-db-ipg {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <456000000>;
+		clock-output-names = "db_ipg_clk";
+	};
+
+	db_pmu0: db-pmu@5ca40000 {
+		compatible = "fsl,imx8dxl-db-pmu";
+		reg = <0x5ca40000 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&db_pmu0_lpcg IMX_LPCG_CLK_0>,
+			 <&db_pmu0_lpcg IMX_LPCG_CLK_1>;
+		clock-names = "ipg", "cnt";
+		power-domains = <&pd IMX_SC_R_PERF>;
+	};
+
+	db_pmu0_lpcg: clock-controller@5cae0000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5cae0000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&db_ipg_clk>, <&db_ipg_clk>;
+		clock-indices = <IMX_LPCG_CLK_0>,
+				<IMX_LPCG_CLK_1>;
+		clock-output-names = "perf_lpcg_cnt_clk",
+				     "perf_lpcg_ipg_clk";
+		power-domains = <&pd IMX_SC_R_PERF>;
+	};
+};
Signature · 1 line
2.34.1
author
#5 lore raw

PATCH v5 5/8 arm64: dts: freescale: Add lsio subsys dtsi for imx8dxl

In reply to Abel Vesa

From: Jacky Bai <[email protected]>

On i.MX8DXL, the LSIO subsystem includes below devices:

1x Inline Encryption Engine (IEE)
1x FlexSPI
4x Pulse Width Modulator (PWM)
5x General Purpose Timer (GPT)
8x GPIO
14x Message Unit (MU)
256KB On-Chip Memory (OCRAM)

compared to the common imx8-ss-lsio dtsi, some nodes' interrupt property need to be updated.

---
 .../boot/dts/freescale/imx8dxl-ss-lsio.dtsi   | 78 +++++++++++++++++++
 1 file changed, 78 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi new file +78 -0
new file mode 100644
index 000000000000..d90602bab384
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019-2021 NXP
+ */
+&lsio_gpio0 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio1 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio2 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio3 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio4 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio5 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio6 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio7 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu0 {
+	compatible = "fsl,imx8dxl-mu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu1 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu2 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu3 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu4 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu5 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu13 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+};
Signature · 1 line
2.34.1
author
#6 lore raw

PATCH v5 6/8 arm64: dts: freescale: Add i.MX8DXL evk board support

In reply to Abel Vesa

From: Jacky Bai <[email protected]>

Add i.MX8DXL EVK board support.

---
 arch/arm64/boot/dts/freescale/Makefile        |   1 +
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 266 ++++++++++++++++++
 2 files changed, 267 insertions(+)
 create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
arch/arm64/boot/dts/freescale/Makefile +1 -0
index 7f51b537df40..1110209f5625 100644
@@ -93,6 +93,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qm-mek.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
arch/arm64/boot/dts/freescale/imx8dxl-evk.dts new file +266 -0

266 lines not on this page · raw message

Signature · 1 line
2.34.1
author
#7 lore raw

PATCH v5 7/8 dt-bindings: fsl: scu: Add i.MX8DXL ocotp binding

In reply to Abel Vesa

Add i.MX8DXL ocotp compatible to the SCU bindings documentation.

---
 Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +2 -1
index a87ec15e28d2..5603b8a70089 100644
@@ -142,7 +142,8 @@ OCOTP bindings based on SCU Message Protocol
 Required properties:
 - compatible:		Should be one of:
 			"fsl,imx8qm-scu-ocotp",
-			"fsl,imx8qxp-scu-ocotp".
+			"fsl,imx8qxp-scu-ocotp",
+			"fsl,imx8dxl-scu-ocotp".
 - #address-cells:	Must be 1. Contains byte index
 - #size-cells:		Must be 1. Contains byte length
 
Signature · 1 line
2.34.1
author
#8 lore raw

PATCH v5 8/8 dt-bindings: net: dwmac-imx: Document clk_csr property

In reply to Abel Vesa

The clk_csr property is used for CSR clock range selection.

---
 Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +4 -0
index 011363166789..1556d95943f6 100644
@@ -32,6 +32,10 @@ properties:
               - nxp,imx8dxl-dwmac-eqos
           - const: snps,dwmac-5.10a
 
+  clk_csr:
+    description: |
+      Fixed CSR Clock Range selection
+
   clocks:
     minItems: 3
     items:
Signature · 1 line
2.34.1
maintainer
#9 lore raw

Re: [PATCH v5 8/8] dt-bindings: net: dwmac-imx: Document clk_csr property

Quoted 1 line · Abel Vesa

The clk_csr property is used for CSR clock range selection.

Why?

Quoted 11 lines
---
 Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +0 -0
index 011363166789..1556d95943f6 100644

Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml properties: · line 35

Quoted 4 lines
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +1 -0
@@ -32,6 +32,10 @@ properties:
               - nxp,imx8dxl-dwmac-eqos
           - const: snps,dwmac-5.10a
 
+  clk_csr:

s/_/-/

vendor prefix needed.

And a type is needed.

Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml properties: · line 37

Quoted 2 lines
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +2 -0
+    description: |
+      Fixed CSR Clock Range selection

What? Explain all this to someone that doesn't know your h/w.

Quoted 8 lines
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +1 -0
+
   clocks:
     minItems: 3
     items:
Signature · 1 line
2.34.1
author
#10 lore raw

Re: [PATCH v5 8/8] dt-bindings: net: dwmac-imx: Document clk_csr property

Quoted 4 lines · Rob Herring
Quoted 1 line · Abel Vesa

The clk_csr property is used for CSR clock range selection.

Why?

Well, this actually documented in Documentation/networking/device_drivers/ethernet/stmicro/stmmac.rst.

But I think I'll just drop this one and remove the property from the devicetree node for now. We'll figure it out later when the ethernet support will be upstreamed.

Quoted 36 lines
Quoted 12 lines
---
 Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml | 4 ++++
 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +0 -0
index 011363166789..1556d95943f6 100644

Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml properties: · line 35

Quoted 4 lines
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +1 -0
@@ -32,6 +32,10 @@ properties:
               - nxp,imx8dxl-dwmac-eqos
           - const: snps,dwmac-5.10a
 
+  clk_csr:

s/_/-/

vendor prefix needed.

And a type is needed.

Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml properties: · line 37

Quoted 2 lines
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +2 -0
+    description: |
+      Fixed CSR Clock Range selection

What? Explain all this to someone that doesn't know your h/w.

Quoted 8 lines
Documentation/devicetree/bindings/net/nxp,dwmac-imx.yaml +1 -1
+
   clocks:
     minItems: 3
     items:
--

2.34.1