imx8mn_ddr4_evk: Add USB Mass Storage support
Subsystems (3)
Fabio Estevam
reviewerPATCH v2 1/2 imx8mn_ddr4_evk: Add USB Mass Storage support
From: Fabio Estevam <[email protected]>
Add USB Mass Storage support, which is a convenient way to flash the eMMC card, for example.
---
Changes since v1:
- None
configs/imx8mn_ddr4_evk_defconfig | 12 ++++++++++++ 1 file changed, 12 insertions(+)
configs/imx8mn_ddr4_evk_defconfig +12 -0
@@ -42,6 +42,8 @@ CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y +CONFIG_CMD_USB_MASS_STORAGE=y CONFIG_CMD_CACHE=y CONFIG_CMD_REGULATOR=y CONFIG_CMD_EXT4_WRITE=y
@@ -82,4 +84,14 @@ CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_PSCI=y CONFIG_SYSRESET_WATCHDOG=y CONFIG_DM_THERMAL=y +CONFIG_USB=y +# CONFIG_SPL_DM_USB is not set +CONFIG_USB_EHCI_HCD=y +CONFIG_MXC_USB_OTG_HACTIVE=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="FSL" +CONFIG_USB_GADGET_VENDOR_NUM=0x0525 +CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5 +CONFIG_CI_UDC=y +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_IMX_WATCHDOG=y
Signature · 1 line
2.25.1
Fabio Estevam
reviewerPATCH v2 2/2 imx8mn/8mp: Allow booting via USB
From: Fabio Estevam <[email protected]>
When trying to boot via USB on i.MX8MN it is necessary to specify the U-Boot environment location, otherwise the boot process simply hangs.
Specify the environment location when booting from USB.
Tested on a imx8mn-evk.
---
Changes since v1:
- Handle the env selection for the USB_BOOT case (Michael).
arch/arm/mach-imx/imx8m/soc.c | 8 ++++++++ 1 file changed, 8 insertions(+)
arch/arm/mach-imx/imx8m/soc.c +8 -0
@@ -1536,6 +1536,14 @@ enum env_location arch_env_get_location(enum env_operation op, int prio)return ENVL_UNKNOWN ;switch (dev) { +case USB_BOOT : +if (IS_ENABLED (CONFIG_ENV_IS_IN_SPI_FLASH )) +return ENVL_SPI_FLASH ; +if (IS_ENABLED (CONFIG_ENV_IS_IN_NAND )) +return ENVL_NAND ; +if (IS_ENABLED (CONFIG_ENV_IS_IN_MMC )) +return ENVL_MMC ; +return ENVL_NOWHERE ;case QSPI_BOOT :case SPI_NOR_BOOT :if (IS_ENABLED (CONFIG_ENV_IS_IN_SPI_FLASH ))
Signature · 1 line
2.25.1
Re: [PATCH v2 2/2] imx8mn/8mp: Allow booting via USB
Quoted 25 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
When trying to boot via USB on i.MX8MN it is necessary to specify the U-Boot environment location, otherwise the boot process simply hangs.
Specify the environment location when booting from USB.
Tested on a imx8mn-evk.
Suggested-by Michael Nazzareno Trimarchi <[email protected]>Signed-off-by Fabio Estevam <[email protected]>---
Changes since v1:
- Handle the env selection for theUSB_BOOTcase (Michael).arch/arm/mach-imx/imx8m/soc.c | 8 ++++++++ 1 file changed, 8 insertions(+)arch/arm/mach-imx/imx8m/soc.c +0
-0@@ -1536,6 +1536,14 @@ enum env_location arch_env_get_location(enum env_operation op, int prio)return ENVL_UNKNOWN ;
arch/arm/mach-imx/imx8m/soc.c enum env_location arch_env_get_location(enum env_operation op, int prio) · line 1546
Quoted 10 lines
arch/arm/mach-imx/imx8m/soc.c +8
-0switch (dev) { +case USB_BOOT : +if (IS_ENABLED (CONFIG_ENV_IS_IN_SPI_FLASH )) +return ENVL_SPI_FLASH ; +if (IS_ENABLED (CONFIG_ENV_IS_IN_NAND )) +return ENVL_NAND ; +if (IS_ENABLED (CONFIG_ENV_IS_IN_MMC )) +return ENVL_MMC ; +return ENVL_NOWHERE ;
Shouldn't this last entry also be
if (IS_ENABLED(CONFIG_ENV_IS_NOWHERE))
return ENVL_NOWHERE;
?