imx8mn_evk: Enable cache in SPL
Fabio Estevam
reviewerPATCH 1/2 imx8mn_evk: Enable cache in SPL
From: Fabio Estevam <[email protected]>
There is no reason for disabling I-cache and D-cache in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF andCONFIG_SPL_SYS_DCACHE_OFF options.
--- configs/imx8mn_evk_defconfig | 2 -- 1 file changed, 2 deletions(-)
configs/imx8mn_evk_defconfig +0 -2
@@ -1,6 +1,4 @@ CONFIG_ARM=y -CONFIG_SPL_SYS_ICACHE_OFF=y -CONFIG_SPL_SYS_DCACHE_OFF=y CONFIG_ARCH_IMX8M=y CONFIG_SYS_TEXT_BASE=0x40200000 CONFIG_SYS_MALLOC_LEN=0x2000000
Signature · 1 line
2.25.1
Fabio Estevam
reviewerPATCH 2/2 doc: imx8mn_evk: Do not export ATF_LOAD_ADDR
From: Fabio Estevam <[email protected]>
The imx8mn_evk target have been converted to use binman.
With the binman approach the ATF load address is described via devicetree, so remove the now unneeded instruction of exporting ATF_LOAD_ADDR.
--- doc/board/nxp/imx8mn_evk.rst | 1 - 1 file changed, 1 deletion(-)
doc/board/nxp/imx8mn_evk.rst +0 -1
@@ -42,7 +42,6 @@ Build U-Boot $ export CROSS_COMPILE=aarch64-poky-linux- $ make imx8mn_ddr4_evk_defconfig - $ export ATF_LOAD_ADDR=0x960000 $ make Burn the flash.bin to MicroSD card offset 32KB:
Signature · 1 line
2.25.1
PATCH 2/2 doc: imx8mn_evk: Do not export ATF_LOAD_ADDR
Quoted 6 lines
From: Fabio Estevam <[email protected]>
Theimx8mn_evktarget have been converted to use binman. With the binman approach the ATF load address is described via devicetree, so remove the now unneeded instruction of exportingATF_LOAD_ADDR.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Re: [PATCH 2/2] doc: imx8mn_evk: Do not export ATF_LOAD_ADDR
In reply to Fabio EstevamQuoted 9 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
The
imx8mn_evktarget have been converted to use binman.With the binman approach the ATF load address is described via devicetree, so remove the now unneeded instruction of exporting
ATF_LOAD_ADDR.Signed-off-by Fabio Estevam <[email protected]>
Quoted 17 lines
--- doc/board/nxp/imx8mn_evk.rst | 1 - 1 file changed, 1 deletion(-)doc/board/nxp/imx8mn_evk.rst +0
-1@@ -42,7 +42,6 @@ Build U-Boot $ export CROSS_COMPILE=aarch64-poky-linux- $ make imx8mn_ddr4_evk_defconfig - $ export ATF_LOAD_ADDR=0x960000 $ make Burn the flash.bin to MicroSD card offset 32KB:
PATCH 1/2 imx8mn_evk: Enable cache in SPL
In reply to Fabio EstevamQuoted 6 lines
From: Fabio Estevam <[email protected]>
There is no reason for disabling I-cache and D-cache in SPL.
Remove the unneededCONFIG_SPL_SYS_ICACHE_OFFandCONFIG_SPL_SYS_DCACHE_OFFoptions.Signed-off-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Quoted 9 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
There is no reason for disabling I-cache and D-cache in SPL.
Remove the unneeded
CONFIG_SPL_SYS_ICACHE_OFFandCONFIG_SPL_SYS_DCACHE_OFFoptions.Signed-off-by Fabio Estevam <[email protected]>
Quoted 16 lines
--- configs/imx8mn_evk_defconfig | 2 -- 1 file changed, 2 deletions(-)configs/imx8mn_evk_defconfig +0
-2@@ -1,6 +1,4 @@ CONFIG_ARM=y -CONFIG_SPL_SYS_ICACHE_OFF=y -CONFIG_SPL_SYS_DCACHE_OFF=y CONFIG_ARCH_IMX8M=y CONFIG_SYS_TEXT_BASE=0x40200000 CONFIG_SYS_MALLOC_LEN=0x2000000