Skip to contentSkip to conversation

Enable designware PCI EP EDMA locally

PATCH Superseded Frank Li 5 participants 27 messages Apr 22, 2022 – Apr 29, 2022

Subsystems (4)

v9 of 12 Superseded Latest is v12 →

lore
Share & tools
lore

Frank Li

author
#0 lore raw

v9 cover Enable designware PCI EP EDMA locally

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (7):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags
PCI: endpoint: Add embedded DMA controller test

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 139 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  54 ++++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  10 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 8 files changed, 312 insertions(+), 176 deletions(-)
Signature · 1 line
2.35.1
author
#1 lore raw

PATCH v9 1/9 dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip

irq of struct dw_edma_chip was never used.
It can be removed safely.

---
Change from v7 to v9
- None
Change from v6 to v7
- move to 1st patch
Change from v5 to v6
- s/remove/Remove/ at subject
Change from v4 to v5
- none
new patch at v4

 drivers/dma/dw-edma/dw-edma-pcie.c | 1 -
 include/linux/dma/edma.h           | 2 --
 2 files changed, 3 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +0 -1
index 44f6e09bdb531..b8f52ca10fa91 100644
@@ -231,7 +231,6 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->dw = dw;
 	chip->dev = dev;
 	chip->id = pdev->devfn;
-	chip->irq = pdev->irq;
 
 	dw->mf = vsec_data.mf;
 	dw->nr_irqs = nr_irqs;
include/linux/dma/edma.h +0 -2
index cab6e18773dad..d4333e721588d 100644
@@ -18,13 +18,11 @@ struct dw_edma;
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
- * @irq:		 irq line
  * @dw:			 struct dw_edma that is filed by dw_edma_probe()
  */
 struct dw_edma_chip {
 	struct device		*dev;
 	int			id;
-	int			irq;
 	struct dw_edma		*dw;
 };
 
Signature · 1 line
2.35.1
Reviewed-by on v9 1/9
#2 lore raw

Re: [PATCH v9 1/9] dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip

Quoted 4 lines · Frank Li

irq of struct dw_edma_chip was never used.
It can be removed safely.

Thanks,
Mani

Quoted 49 lines

---
Change from v7 to v9
- None
Change from v6 to v7
- move to 1st patch
Change from v5 to v6
- s/remove/Remove/ at subject
Change from v4 to v5
- none
new patch at v4

 drivers/dma/dw-edma/dw-edma-pcie.c | 1 -
 include/linux/dma/edma.h           | 2 --
 2 files changed, 3 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +0 -1
index 44f6e09bdb531..b8f52ca10fa91 100644
@@ -231,7 +231,6 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->dw = dw;
 	chip->dev = dev;
 	chip->id = pdev->devfn;
-	chip->irq = pdev->irq;
 
 	dw->mf = vsec_data.mf;
 	dw->nr_irqs = nr_irqs;
include/linux/dma/edma.h +0 -2
index cab6e18773dad..d4333e721588d 100644
@@ -18,13 +18,11 @@ struct dw_edma;
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
- * @irq:		 irq line
  * @dw:			 struct dw_edma that is filed by dw_edma_probe()
  */
 struct dw_edma_chip {
 	struct device		*dev;
 	int			id;
-	int			irq;
 	struct dw_edma		*dw;
 };
 
Signature · 1 line
2.35.1
author
#3 lore raw

PATCH v9 2/9 dmaengine: dw-edma: Detach the private data and chip info structures

In reply to Frank Li

"struct dw_edma_chip" contains an internal structure "struct dw_edma" that is used by the eDMA core internally. This structure should not be touched by the eDMA controller drivers themselves. But currently, the eDMA controller drivers like "dw-edma-pci" allocates and populates this internal structure then passes it on to eDMA core. The eDMA core further populates the structure and uses it. This is wrong!

Hence, move all the "struct dw_edma" specifics from controller drivers to the eDMA core.

---
Change from v8 to v9
- remove chip->ops check at dw_edma_irq_request()
Change from v7 to v8
- Check chip->ops at probe()
- use struct edma_dw at dw_edma_v0_debugfs_on/off()

Change from v6 to v7
- Move nr_irqs and chip->ops check into dw_edma_irq_request()
- Move dw->irq devm_kcalloc() into dw_edma_irq_request()
- Change dw->nr_irqs after request success
- Fix wrong use chip->nr_irqs when remove

Change from v5 to v6
- Don't touch chip->nr_irqs
- Don't set chip->dw utill everything is okay
- dw_edma_channel_setup() and dw_edma_v0_core_debugfs_on/off() methods take dw_edma structure pointer as a parameter

Change from v4 to v5
- Move chip->nr_irqs before allocate dw_edma
Change from v3 to v4
- Accept most suggestions of Serge Semin
Change from v2 to v3
- none
Change from v1 to v2
- rework commit message
- remove duplicate field in struct dw_edma

 drivers/dma/dw-edma/dw-edma-core.c       | 90 +++++++++++++-----------
 drivers/dma/dw-edma/dw-edma-core.h       | 31 +-------
 drivers/dma/dw-edma/dw-edma-pcie.c       | 82 +++++++++------------
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 32 ++++-----
 drivers/dma/dw-edma/dw-edma-v0-core.h    |  4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 18 ++---
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h |  8 +--
 include/linux/dma/edma.h                 | 44 ++++++++++++
 8 files changed, 161 insertions(+), 148 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +49 -41
index 53289927dd0d6..58e91fe384282 100644
@@ -64,8 +64,8 @@ static struct dw_edma_burst *dw_edma_alloc_burst(struct dw_edma_chunk *chunk)
 
 static struct dw_edma_chunk *dw_edma_alloc_chunk(struct dw_edma_desc *desc)
 {
+	struct dw_edma_chip *chip = desc->chan->dw->chip;
 	struct dw_edma_chan *chan = desc->chan;
-	struct dw_edma *dw = chan->chip->dw;
 	struct dw_edma_chunk *chunk;
 
 	chunk = kzalloc(sizeof(*chunk), GFP_NOWAIT);
@@ -82,11 +82,11 @@ static struct dw_edma_chunk *dw_edma_alloc_chunk(struct dw_edma_desc *desc)
 	 */
 	chunk->cb = !(desc->chunks_alloc % 2);
 	if (chan->dir == EDMA_DIR_WRITE) {
-		chunk->ll_region.paddr = dw->ll_region_wr[chan->id].paddr;
-		chunk->ll_region.vaddr = dw->ll_region_wr[chan->id].vaddr;
+		chunk->ll_region.paddr = chip->ll_region_wr[chan->id].paddr;
+		chunk->ll_region.vaddr = chip->ll_region_wr[chan->id].vaddr;
 	} else {
-		chunk->ll_region.paddr = dw->ll_region_rd[chan->id].paddr;
-		chunk->ll_region.vaddr = dw->ll_region_rd[chan->id].vaddr;
+		chunk->ll_region.paddr = chip->ll_region_rd[chan->id].paddr;
+		chunk->ll_region.vaddr = chip->ll_region_rd[chan->id].vaddr;
 	}
 
 	if (desc->chunk) {
@@ -664,7 +664,7 @@ static int dw_edma_alloc_chan_resources(struct dma_chan *dchan)
 	if (chan->status != EDMA_ST_IDLE)
 		return -EBUSY;
 
-	pm_runtime_get(chan->chip->dev);
+	pm_runtime_get(chan->dw->chip->dev);
 
 	return 0;
 }
@@ -686,15 +686,15 @@ static void dw_edma_free_chan_resources(struct dma_chan *dchan)
 		cpu_relax();
 	}
 
-	pm_runtime_put(chan->chip->dev);
+	pm_runtime_put(chan->dw->chip->dev);
 }
 
-static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
+static int dw_edma_channel_setup(struct dw_edma *dw, bool write,
 				 u32 wr_alloc, u32 rd_alloc)
 {
+	struct dw_edma_chip *chip = dw->chip;
 	struct dw_edma_region *dt_region;
 	struct device *dev = chip->dev;
-	struct dw_edma *dw = chip->dw;
 	struct dw_edma_chan *chan;
 	struct dw_edma_irq *irq;
 	struct dma_device *dma;
@@ -727,7 +727,7 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 
 		chan->vc.chan.private = dt_region;
 
-		chan->chip = chip;
+		chan->dw = dw;
 		chan->id = j;
 		chan->dir = write ? EDMA_DIR_WRITE : EDMA_DIR_READ;
 		chan->configured = false;
@@ -735,9 +735,9 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 		chan->status = EDMA_ST_IDLE;
 
 		if (write)
-			chan->ll_max = (dw->ll_region_wr[j].sz / EDMA_LL_SZ);
+			chan->ll_max = (chip->ll_region_wr[j].sz / EDMA_LL_SZ);
 		else
-			chan->ll_max = (dw->ll_region_rd[j].sz / EDMA_LL_SZ);
+			chan->ll_max = (chip->ll_region_rd[j].sz / EDMA_LL_SZ);
 		chan->ll_max -= 1;
 
 		dev_vdbg(dev, "L. List:\tChannel %s[%u] max_cnt=%u\n",
@@ -767,13 +767,13 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 		vchan_init(&chan->vc, dma);
 
 		if (write) {
-			dt_region->paddr = dw->dt_region_wr[j].paddr;
-			dt_region->vaddr = dw->dt_region_wr[j].vaddr;
-			dt_region->sz = dw->dt_region_wr[j].sz;
+			dt_region->paddr = chip->dt_region_wr[j].paddr;
+			dt_region->vaddr = chip->dt_region_wr[j].vaddr;
+			dt_region->sz = chip->dt_region_wr[j].sz;
 		} else {
-			dt_region->paddr = dw->dt_region_rd[j].paddr;
-			dt_region->vaddr = dw->dt_region_rd[j].vaddr;
-			dt_region->sz = dw->dt_region_rd[j].sz;
+			dt_region->paddr = chip->dt_region_rd[j].paddr;
+			dt_region->vaddr = chip->dt_region_rd[j].vaddr;
+			dt_region->sz = chip->dt_region_rd[j].sz;
 		}
 
 		dw_edma_v0_core_device_config(chan);
@@ -827,11 +827,11 @@ static inline void dw_edma_add_irq_mask(u32 *mask, u32 alloc, u16 cnt)
 		(*mask)++;
 }
 
-static int dw_edma_irq_request(struct dw_edma_chip *chip,
+static int dw_edma_irq_request(struct dw_edma *dw,
 			       u32 *wr_alloc, u32 *rd_alloc)
 {
-	struct device *dev = chip->dev;
-	struct dw_edma *dw = chip->dw;
+	struct dw_edma_chip *chip = dw->chip;
+	struct device *dev = dw->chip->dev;
 	u32 wr_mask = 1;
 	u32 rd_mask = 1;
 	int i, err = 0;
@@ -840,12 +840,16 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 
 	ch_cnt = dw->wr_ch_cnt + dw->rd_ch_cnt;
 
-	if (dw->nr_irqs < 1)
+	if (chip->nr_irqs < 1 || !chip->ops->irq_vector)
 		return -EINVAL;
 
-	if (dw->nr_irqs == 1) {
+	dw->irq = devm_kcalloc(dev, chip->nr_irqs, sizeof(*dw->irq), GFP_KERNEL);
+	if (!dw->irq)
+		return -ENOMEM;
+
+	if (chip->nr_irqs == 1) {
 		/* Common IRQ shared among all channels */
-		irq = dw->ops->irq_vector(dev, 0);
+		irq = chip->ops->irq_vector(dev, 0);
 		err = request_irq(irq, dw_edma_interrupt_common,
 				  IRQF_SHARED, dw->name, &dw->irq[0]);
 		if (err) {
@@ -855,9 +859,11 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 
 		if (irq_get_msi_desc(irq))
 			get_cached_msi_msg(irq, &dw->irq[0].msi);
+
+		dw->nr_irqs = 1;
 	} else {
 		/* Distribute IRQs equally among all channels */
-		int tmp = dw->nr_irqs;
+		int tmp = chip->nr_irqs;
 
 		while (tmp && (*wr_alloc + *rd_alloc) < ch_cnt) {
 			dw_edma_dec_irq_alloc(&tmp, wr_alloc, dw->wr_ch_cnt);
@@ -868,7 +874,7 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 		dw_edma_add_irq_mask(&rd_mask, *rd_alloc, dw->rd_ch_cnt);
 
 		for (i = 0; i < (*wr_alloc + *rd_alloc); i++) {
-			irq = dw->ops->irq_vector(dev, i);
+			irq = chip->ops->irq_vector(dev, i);
 			err = request_irq(irq,
 					  i < *wr_alloc ?
 						dw_edma_interrupt_write :
@@ -902,20 +908,22 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 		return -EINVAL;
 
 	dev = chip->dev;
-	if (!dev)
+	if (!dev || !chip->ops)
 		return -EINVAL;
 
-	dw = chip->dw;
-	if (!dw || !dw->irq || !dw->ops || !dw->ops->irq_vector)
-		return -EINVAL;
+	dw = devm_kzalloc(dev, sizeof(*dw), GFP_KERNEL);
+	if (!dw)
+		return -ENOMEM;
+
+	dw->chip = chip;
 
 	raw_spin_lock_init(&dw->lock);
 
-	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt,
+	dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
 	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt,
+	dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
 	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
@@ -937,17 +945,17 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 	dw_edma_v0_core_off(dw);
 
 	/* Request IRQs */
-	err = dw_edma_irq_request(chip, &wr_alloc, &rd_alloc);
+	err = dw_edma_irq_request(dw, &wr_alloc, &rd_alloc);
 	if (err)
 		return err;
 
 	/* Setup write channels */
-	err = dw_edma_channel_setup(chip, true, wr_alloc, rd_alloc);
+	err = dw_edma_channel_setup(dw, true, wr_alloc, rd_alloc);
 	if (err)
 		goto err_irq_free;
 
 	/* Setup read channels */
-	err = dw_edma_channel_setup(chip, false, wr_alloc, rd_alloc);
+	err = dw_edma_channel_setup(dw, false, wr_alloc, rd_alloc);
 	if (err)
 		goto err_irq_free;
 
@@ -955,15 +963,15 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 	pm_runtime_enable(dev);
 
 	/* Turn debugfs on */
-	dw_edma_v0_core_debugfs_on(chip);
+	dw_edma_v0_core_debugfs_on(dw);
+
+	chip->dw = dw;
 
 	return 0;
 
 err_irq_free:
 	for (i = (dw->nr_irqs - 1); i >= 0; i--)
-		free_irq(dw->ops->irq_vector(dev, i), &dw->irq[i]);
-
-	dw->nr_irqs = 0;
+		free_irq(chip->ops->irq_vector(dev, i), &dw->irq[i]);
 
 	return err;
 }
@@ -981,7 +989,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)
 
 	/* Free irqs */
 	for (i = (dw->nr_irqs - 1); i >= 0; i--)
-		free_irq(dw->ops->irq_vector(dev, i), &dw->irq[i]);
+		free_irq(chip->ops->irq_vector(dev, i), &dw->irq[i]);
 
 	/* Power management */
 	pm_runtime_disable(dev);
@@ -1002,7 +1010,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)
 	}
 
 	/* Turn debugfs off */
-	dw_edma_v0_core_debugfs_off(chip);
+	dw_edma_v0_core_debugfs_off(dw);
 
 	return 0;
 }
drivers/dma/dw-edma/dw-edma-core.h +3 -28
index 60316d408c3e0..85df2d511907b 100644
@@ -15,20 +15,12 @@
 #include "../virt-dma.h"
 
 #define EDMA_LL_SZ					24
-#define EDMA_MAX_WR_CH					8
-#define EDMA_MAX_RD_CH					8
 
 enum dw_edma_dir {
 	EDMA_DIR_WRITE = 0,
 	EDMA_DIR_READ
 };
 
-enum dw_edma_map_format {
-	EDMA_MF_EDMA_LEGACY = 0x0,
-	EDMA_MF_EDMA_UNROLL = 0x1,
-	EDMA_MF_HDMA_COMPAT = 0x5
-};
-
 enum dw_edma_request {
 	EDMA_REQ_NONE = 0,
 	EDMA_REQ_STOP,
@@ -57,12 +49,6 @@ struct dw_edma_burst {
 	u32				sz;
 };
 
-struct dw_edma_region {
-	phys_addr_t			paddr;
-	void				__iomem *vaddr;
-	size_t				sz;
-};
-
 struct dw_edma_chunk {
 	struct list_head		list;
 	struct dw_edma_chan		*chan;
@@ -87,7 +73,7 @@ struct dw_edma_desc {
 
 struct dw_edma_chan {
 	struct virt_dma_chan		vc;
-	struct dw_edma_chip		*chip;
+	struct dw_edma			*dw;
 	int				id;
 	enum dw_edma_dir		dir;
 
@@ -109,10 +95,6 @@ struct dw_edma_irq {
 	struct dw_edma			*dw;
 };
 
-struct dw_edma_core_ops {
-	int	(*irq_vector)(struct device *dev, unsigned int nr);
-};
-
 struct dw_edma {
 	char				name[20];
 
@@ -122,21 +104,14 @@ struct dw_edma {
 	struct dma_device		rd_edma;
 	u16				rd_ch_cnt;
 
-	struct dw_edma_region		rg_region;	/* Registers */
-	struct dw_edma_region		ll_region_wr[EDMA_MAX_WR_CH];
-	struct dw_edma_region		ll_region_rd[EDMA_MAX_RD_CH];
-	struct dw_edma_region		dt_region_wr[EDMA_MAX_WR_CH];
-	struct dw_edma_region		dt_region_rd[EDMA_MAX_RD_CH];
-
 	struct dw_edma_irq		*irq;
 	int				nr_irqs;
 
-	enum dw_edma_map_format		mf;
-
 	struct dw_edma_chan		*chan;
-	const struct dw_edma_core_ops	*ops;
 
 	raw_spinlock_t			lock;		/* Only for legacy */
+
+	struct dw_edma_chip             *chip;
 #ifdef CONFIG_DEBUG_FS
 	struct dentry			*debugfs;
 #endif /* CONFIG_DEBUG_FS */
drivers/dma/dw-edma/dw-edma-pcie.c +34 -48

143 lines not on this page · raw message

drivers/dma/dw-edma/dw-edma-v0-core.c +16 -16
index 329fc2e57b703..6cf6c28ce0cc9 100644
@@ -25,7 +25,7 @@ enum dw_edma_control {
 
 static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 {
-	return dw->rg_region.vaddr;
+	return dw->chip->rg_region.vaddr;
 }
 
 #define SET_32(dw, name, value)				\
@@ -96,7 +96,7 @@ static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 static inline struct dw_edma_v0_ch_regs __iomem *
 __dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY)
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY)
 		return &(__dw_regs(dw)->type.legacy.ch);
 
 	if (dir == EDMA_DIR_WRITE)
@@ -108,7 +108,7 @@ __dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
 static inline void writel_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			     u32 value, void __iomem *addr)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -133,7 +133,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 {
 	u32 value;
 
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -169,7 +169,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 static inline void writeq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			     u64 value, void __iomem *addr)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -194,7 +194,7 @@ static inline u64 readq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 {
 	u32 value;
 
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -256,7 +256,7 @@ u16 dw_edma_v0_core_ch_count(struct dw_edma *dw, enum dw_edma_dir dir)
 
 enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp;
 
 	tmp = FIELD_GET(EDMA_V0_CH_STATUS_MASK,
@@ -272,7 +272,7 @@ enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)
 
 void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 
 	SET_RW_32(dw, chan->dir, int_clear,
 		  FIELD_PREP(EDMA_V0_DONE_INT_MASK, BIT(chan->id)));
@@ -280,7 +280,7 @@ void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan)
 
 void dw_edma_v0_core_clear_abort_int(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 
 	SET_RW_32(dw, chan->dir, int_clear,
 		  FIELD_PREP(EDMA_V0_ABORT_INT_MASK, BIT(chan->id)));
@@ -357,7 +357,7 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 {
 	struct dw_edma_chan *chan = chunk->chan;
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp;
 
 	dw_edma_v0_core_write_chunk(chunk);
@@ -365,7 +365,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 	if (first) {
 		/* Enable engine */
 		SET_RW_32(dw, chan->dir, engine_en, BIT(0));
-		if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+		if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 			switch (chan->id) {
 			case 0:
 				SET_RW_COMPAT(dw, chan->dir, ch0_pwr_en,
@@ -431,7 +431,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 
 int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp = 0;
 
 	/* MSI done addr - low, high */
@@ -501,12 +501,12 @@ int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)
 }
 
 /* eDMA debugfs callbacks */
-void dw_edma_v0_core_debugfs_on(struct dw_edma_chip *chip)
+void dw_edma_v0_core_debugfs_on(struct dw_edma *dw)
 {
-	dw_edma_v0_debugfs_on(chip);
+	dw_edma_v0_debugfs_on(dw);
 }
 
-void dw_edma_v0_core_debugfs_off(struct dw_edma_chip *chip)
+void dw_edma_v0_core_debugfs_off(struct dw_edma *dw)
 {
-	dw_edma_v0_debugfs_off(chip);
+	dw_edma_v0_debugfs_off(dw);
 }
drivers/dma/dw-edma/dw-edma-v0-core.h +2 -2
index 2afa626b8300c..75aec6d31b210 100644
@@ -22,7 +22,7 @@ u32 dw_edma_v0_core_status_abort_int(struct dw_edma *chan, enum dw_edma_dir dir)
 void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first);
 int dw_edma_v0_core_device_config(struct dw_edma_chan *chan);
 /* eDMA debug fs callbacks */
-void dw_edma_v0_core_debugfs_on(struct dw_edma_chip *chip);
-void dw_edma_v0_core_debugfs_off(struct dw_edma_chip *chip);
+void dw_edma_v0_core_debugfs_on(struct dw_edma *dw);
+void dw_edma_v0_core_debugfs_off(struct dw_edma *dw);
 
 #endif /* _DW_EDMA_V0_CORE_H */
drivers/dma/dw-edma/dw-edma-v0-debugfs.c +9 -9
index 4b3bcffd15ef1..b765adb969998 100644
@@ -54,7 +54,7 @@ struct debugfs_entries {
 static int dw_edma_debugfs_u32_get(void *data, u64 *val)
 {
 	void __iomem *reg = (void __force __iomem *)data;
-	if (dw->mf == EDMA_MF_EDMA_LEGACY &&
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY &&
 	    reg >= (void __iomem *)&regs->type.legacy.ch) {
 		void __iomem *ptr = &regs->type.legacy.ch;
 		u32 viewport_sel = 0;
@@ -173,7 +173,7 @@ static void dw_edma_debugfs_regs_wr(struct dentry *dir)
 	nr_entries = ARRAY_SIZE(debugfs_regs);
 	dw_edma_debugfs_create_x32(debugfs_regs, nr_entries, regs_dir);
 
-	if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+	if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 		nr_entries = ARRAY_SIZE(debugfs_unroll_regs);
 		dw_edma_debugfs_create_x32(debugfs_unroll_regs, nr_entries,
 					   regs_dir);
@@ -242,7 +242,7 @@ static void dw_edma_debugfs_regs_rd(struct dentry *dir)
 	nr_entries = ARRAY_SIZE(debugfs_regs);
 	dw_edma_debugfs_create_x32(debugfs_regs, nr_entries, regs_dir);
 
-	if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+	if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 		nr_entries = ARRAY_SIZE(debugfs_unroll_regs);
 		dw_edma_debugfs_create_x32(debugfs_unroll_regs, nr_entries,
 					   regs_dir);
@@ -282,13 +282,13 @@ static void dw_edma_debugfs_regs(void)
 	dw_edma_debugfs_regs_rd(regs_dir);
 }
 
-void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
+void dw_edma_v0_debugfs_on(struct dw_edma *_dw)
 {
-	dw = chip->dw;
+	dw = _dw;
 	if (!dw)
 		return;
 
-	regs = dw->rg_region.vaddr;
+	regs = dw->chip->rg_region.vaddr;
 	if (!regs)
 		return;
 
@@ -296,16 +296,16 @@ void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
 	if (!dw->debugfs)
 		return;
 
-	debugfs_create_u32("mf", 0444, dw->debugfs, &dw->mf);
+	debugfs_create_u32("mf", 0444, dw->debugfs, &dw->chip->mf);
 	debugfs_create_u16("wr_ch_cnt", 0444, dw->debugfs, &dw->wr_ch_cnt);
 	debugfs_create_u16("rd_ch_cnt", 0444, dw->debugfs, &dw->rd_ch_cnt);
 
 	dw_edma_debugfs_regs();
 }
 
-void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip)
+void dw_edma_v0_debugfs_off(struct dw_edma *_dw)
 {
-	dw = chip->dw;
+	dw = _dw;
 	if (!dw)
 		return;
 
drivers/dma/dw-edma/dw-edma-v0-debugfs.h +4 -4
index d0ff25a9ea5c9..3391b86edf5ab 100644
@@ -12,14 +12,14 @@
 #include <linux/dma/edma.h>
 
 #ifdef CONFIG_DEBUG_FS
-void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip);
-void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip);
+void dw_edma_v0_debugfs_on(struct dw_edma *dw);
+void dw_edma_v0_debugfs_off(struct dw_edma *dw);
 #else
-static inline void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
+static inline void dw_edma_v0_debugfs_on(struct dw_edma *dw)
 {
 }
 
-static inline void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip)
+static inline void dw_edma_v0_debugfs_off(struct dw_edma *dw)
 {
 }
 #endif /* CONFIG_DEBUG_FS */
include/linux/dma/edma.h +44 -0

61 lines not on this page · raw message

Signature · 1 line
2.35.1
Reviewed-by on v9 2/9
#4 lore raw

Re: [PATCH v9 2/9] dmaengine: dw-edma: Detach the private data and chip info structures

Quoted 9 lines · Frank Li

"struct dw_edma_chip" contains an internal structure "struct dw_edma" that is used by the eDMA core internally. This structure should not be touched by the eDMA controller drivers themselves. But currently, the eDMA controller drivers like "dw-edma-pci" allocates and populates this internal structure then passes it on to eDMA core. The eDMA core further populates the structure and uses it. This is wrong!

Hence, move all the "struct dw_edma" specifics from controller drivers to the eDMA core.

Great! Thanks.

-Sergey

Quoted 824 lines

---
Change from v8 to v9
- remove chip->ops check at dw_edma_irq_request()
Change from v7 to v8
- Check chip->ops at probe()
- use struct edma_dw at dw_edma_v0_debugfs_on/off()

Change from v6 to v7
- Move nr_irqs and chip->ops check into dw_edma_irq_request()
- Move dw->irq devm_kcalloc() into dw_edma_irq_request()
- Change dw->nr_irqs after request success
- Fix wrong use chip->nr_irqs when remove

Change from v5 to v6
- Don't touch chip->nr_irqs
- Don't set chip->dw utill everything is okay
- dw_edma_channel_setup() and dw_edma_v0_core_debugfs_on/off() methods take dw_edma structure pointer as a parameter

Change from v4 to v5
- Move chip->nr_irqs before allocate dw_edma
Change from v3 to v4
- Accept most suggestions of Serge Semin
Change from v2 to v3
- none
Change from v1 to v2
- rework commit message
- remove duplicate field in struct dw_edma

 drivers/dma/dw-edma/dw-edma-core.c       | 90 +++++++++++++-----------
 drivers/dma/dw-edma/dw-edma-core.h       | 31 +-------
 drivers/dma/dw-edma/dw-edma-pcie.c       | 82 +++++++++------------
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 32 ++++-----
 drivers/dma/dw-edma/dw-edma-v0-core.h    |  4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 18 ++---
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h |  8 +--
 include/linux/dma/edma.h                 | 44 ++++++++++++
 8 files changed, 161 insertions(+), 148 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +49 -41
index 53289927dd0d6..58e91fe384282 100644
@@ -64,8 +64,8 @@ static struct dw_edma_burst *dw_edma_alloc_burst(struct dw_edma_chunk *chunk)
 
 static struct dw_edma_chunk *dw_edma_alloc_chunk(struct dw_edma_desc *desc)
 {
+	struct dw_edma_chip *chip = desc->chan->dw->chip;
 	struct dw_edma_chan *chan = desc->chan;
-	struct dw_edma *dw = chan->chip->dw;
 	struct dw_edma_chunk *chunk;
 
 	chunk = kzalloc(sizeof(*chunk), GFP_NOWAIT);
@@ -82,11 +82,11 @@ static struct dw_edma_chunk *dw_edma_alloc_chunk(struct dw_edma_desc *desc)
 	 */
 	chunk->cb = !(desc->chunks_alloc % 2);
 	if (chan->dir == EDMA_DIR_WRITE) {
-		chunk->ll_region.paddr = dw->ll_region_wr[chan->id].paddr;
-		chunk->ll_region.vaddr = dw->ll_region_wr[chan->id].vaddr;
+		chunk->ll_region.paddr = chip->ll_region_wr[chan->id].paddr;
+		chunk->ll_region.vaddr = chip->ll_region_wr[chan->id].vaddr;
 	} else {
-		chunk->ll_region.paddr = dw->ll_region_rd[chan->id].paddr;
-		chunk->ll_region.vaddr = dw->ll_region_rd[chan->id].vaddr;
+		chunk->ll_region.paddr = chip->ll_region_rd[chan->id].paddr;
+		chunk->ll_region.vaddr = chip->ll_region_rd[chan->id].vaddr;
 	}
 
 	if (desc->chunk) {
@@ -664,7 +664,7 @@ static int dw_edma_alloc_chan_resources(struct dma_chan *dchan)
 	if (chan->status != EDMA_ST_IDLE)
 		return -EBUSY;
 
-	pm_runtime_get(chan->chip->dev);
+	pm_runtime_get(chan->dw->chip->dev);
 
 	return 0;
 }
@@ -686,15 +686,15 @@ static void dw_edma_free_chan_resources(struct dma_chan *dchan)
 		cpu_relax();
 	}
 
-	pm_runtime_put(chan->chip->dev);
+	pm_runtime_put(chan->dw->chip->dev);
 }
 
-static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
+static int dw_edma_channel_setup(struct dw_edma *dw, bool write,
 				 u32 wr_alloc, u32 rd_alloc)
 {
+	struct dw_edma_chip *chip = dw->chip;
 	struct dw_edma_region *dt_region;
 	struct device *dev = chip->dev;
-	struct dw_edma *dw = chip->dw;
 	struct dw_edma_chan *chan;
 	struct dw_edma_irq *irq;
 	struct dma_device *dma;
@@ -727,7 +727,7 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 
 		chan->vc.chan.private = dt_region;
 
-		chan->chip = chip;
+		chan->dw = dw;
 		chan->id = j;
 		chan->dir = write ? EDMA_DIR_WRITE : EDMA_DIR_READ;
 		chan->configured = false;
@@ -735,9 +735,9 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 		chan->status = EDMA_ST_IDLE;
 
 		if (write)
-			chan->ll_max = (dw->ll_region_wr[j].sz / EDMA_LL_SZ);
+			chan->ll_max = (chip->ll_region_wr[j].sz / EDMA_LL_SZ);
 		else
-			chan->ll_max = (dw->ll_region_rd[j].sz / EDMA_LL_SZ);
+			chan->ll_max = (chip->ll_region_rd[j].sz / EDMA_LL_SZ);
 		chan->ll_max -= 1;
 
 		dev_vdbg(dev, "L. List:\tChannel %s[%u] max_cnt=%u\n",
@@ -767,13 +767,13 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 		vchan_init(&chan->vc, dma);
 
 		if (write) {
-			dt_region->paddr = dw->dt_region_wr[j].paddr;
-			dt_region->vaddr = dw->dt_region_wr[j].vaddr;
-			dt_region->sz = dw->dt_region_wr[j].sz;
+			dt_region->paddr = chip->dt_region_wr[j].paddr;
+			dt_region->vaddr = chip->dt_region_wr[j].vaddr;
+			dt_region->sz = chip->dt_region_wr[j].sz;
 		} else {
-			dt_region->paddr = dw->dt_region_rd[j].paddr;
-			dt_region->vaddr = dw->dt_region_rd[j].vaddr;
-			dt_region->sz = dw->dt_region_rd[j].sz;
+			dt_region->paddr = chip->dt_region_rd[j].paddr;
+			dt_region->vaddr = chip->dt_region_rd[j].vaddr;
+			dt_region->sz = chip->dt_region_rd[j].sz;
 		}
 
 		dw_edma_v0_core_device_config(chan);
@@ -827,11 +827,11 @@ static inline void dw_edma_add_irq_mask(u32 *mask, u32 alloc, u16 cnt)
 		(*mask)++;
 }
 
-static int dw_edma_irq_request(struct dw_edma_chip *chip,
+static int dw_edma_irq_request(struct dw_edma *dw,
 			       u32 *wr_alloc, u32 *rd_alloc)
 {
-	struct device *dev = chip->dev;
-	struct dw_edma *dw = chip->dw;
+	struct dw_edma_chip *chip = dw->chip;
+	struct device *dev = dw->chip->dev;
 	u32 wr_mask = 1;
 	u32 rd_mask = 1;
 	int i, err = 0;
@@ -840,12 +840,16 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 
 	ch_cnt = dw->wr_ch_cnt + dw->rd_ch_cnt;
 
-	if (dw->nr_irqs < 1)
+	if (chip->nr_irqs < 1 || !chip->ops->irq_vector)
 		return -EINVAL;
 
-	if (dw->nr_irqs == 1) {
+	dw->irq = devm_kcalloc(dev, chip->nr_irqs, sizeof(*dw->irq), GFP_KERNEL);
+	if (!dw->irq)
+		return -ENOMEM;
+
+	if (chip->nr_irqs == 1) {
 		/* Common IRQ shared among all channels */
-		irq = dw->ops->irq_vector(dev, 0);
+		irq = chip->ops->irq_vector(dev, 0);
 		err = request_irq(irq, dw_edma_interrupt_common,
 				  IRQF_SHARED, dw->name, &dw->irq[0]);
 		if (err) {
@@ -855,9 +859,11 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 
 		if (irq_get_msi_desc(irq))
 			get_cached_msi_msg(irq, &dw->irq[0].msi);
+
+		dw->nr_irqs = 1;
 	} else {
 		/* Distribute IRQs equally among all channels */
-		int tmp = dw->nr_irqs;
+		int tmp = chip->nr_irqs;
 
 		while (tmp && (*wr_alloc + *rd_alloc) < ch_cnt) {
 			dw_edma_dec_irq_alloc(&tmp, wr_alloc, dw->wr_ch_cnt);
@@ -868,7 +874,7 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 		dw_edma_add_irq_mask(&rd_mask, *rd_alloc, dw->rd_ch_cnt);
 
 		for (i = 0; i < (*wr_alloc + *rd_alloc); i++) {
-			irq = dw->ops->irq_vector(dev, i);
+			irq = chip->ops->irq_vector(dev, i);
 			err = request_irq(irq,
 					  i < *wr_alloc ?
 						dw_edma_interrupt_write :
@@ -902,20 +908,22 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 		return -EINVAL;
 
 	dev = chip->dev;
-	if (!dev)
+	if (!dev || !chip->ops)
 		return -EINVAL;
 
-	dw = chip->dw;
-	if (!dw || !dw->irq || !dw->ops || !dw->ops->irq_vector)
-		return -EINVAL;
+	dw = devm_kzalloc(dev, sizeof(*dw), GFP_KERNEL);
+	if (!dw)
+		return -ENOMEM;
+
+	dw->chip = chip;
 
 	raw_spin_lock_init(&dw->lock);
 
-	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt,
+	dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
 	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt,
+	dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
 	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
@@ -937,17 +945,17 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 	dw_edma_v0_core_off(dw);
 
 	/* Request IRQs */
-	err = dw_edma_irq_request(chip, &wr_alloc, &rd_alloc);
+	err = dw_edma_irq_request(dw, &wr_alloc, &rd_alloc);
 	if (err)
 		return err;
 
 	/* Setup write channels */
-	err = dw_edma_channel_setup(chip, true, wr_alloc, rd_alloc);
+	err = dw_edma_channel_setup(dw, true, wr_alloc, rd_alloc);
 	if (err)
 		goto err_irq_free;
 
 	/* Setup read channels */
-	err = dw_edma_channel_setup(chip, false, wr_alloc, rd_alloc);
+	err = dw_edma_channel_setup(dw, false, wr_alloc, rd_alloc);
 	if (err)
 		goto err_irq_free;
 
@@ -955,15 +963,15 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 	pm_runtime_enable(dev);
 
 	/* Turn debugfs on */
-	dw_edma_v0_core_debugfs_on(chip);
+	dw_edma_v0_core_debugfs_on(dw);
+
+	chip->dw = dw;
 
 	return 0;
 
 err_irq_free:
 	for (i = (dw->nr_irqs - 1); i >= 0; i--)
-		free_irq(dw->ops->irq_vector(dev, i), &dw->irq[i]);
-
-	dw->nr_irqs = 0;
+		free_irq(chip->ops->irq_vector(dev, i), &dw->irq[i]);
 
 	return err;
 }
@@ -981,7 +989,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)
 
 	/* Free irqs */
 	for (i = (dw->nr_irqs - 1); i >= 0; i--)
-		free_irq(dw->ops->irq_vector(dev, i), &dw->irq[i]);
+		free_irq(chip->ops->irq_vector(dev, i), &dw->irq[i]);
 
 	/* Power management */
 	pm_runtime_disable(dev);
@@ -1002,7 +1010,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)
 	}
 
 	/* Turn debugfs off */
-	dw_edma_v0_core_debugfs_off(chip);
+	dw_edma_v0_core_debugfs_off(dw);
 
 	return 0;
 }
drivers/dma/dw-edma/dw-edma-core.h +3 -28
index 60316d408c3e0..85df2d511907b 100644
@@ -15,20 +15,12 @@
 #include "../virt-dma.h"
 
 #define EDMA_LL_SZ					24
-#define EDMA_MAX_WR_CH					8
-#define EDMA_MAX_RD_CH					8
 
 enum dw_edma_dir {
 	EDMA_DIR_WRITE = 0,
 	EDMA_DIR_READ
 };
 
-enum dw_edma_map_format {
-	EDMA_MF_EDMA_LEGACY = 0x0,
-	EDMA_MF_EDMA_UNROLL = 0x1,
-	EDMA_MF_HDMA_COMPAT = 0x5
-};
-
 enum dw_edma_request {
 	EDMA_REQ_NONE = 0,
 	EDMA_REQ_STOP,
@@ -57,12 +49,6 @@ struct dw_edma_burst {
 	u32				sz;
 };
 
-struct dw_edma_region {
-	phys_addr_t			paddr;
-	void				__iomem *vaddr;
-	size_t				sz;
-};
-
 struct dw_edma_chunk {
 	struct list_head		list;
 	struct dw_edma_chan		*chan;
@@ -87,7 +73,7 @@ struct dw_edma_desc {
 
 struct dw_edma_chan {
 	struct virt_dma_chan		vc;
-	struct dw_edma_chip		*chip;
+	struct dw_edma			*dw;
 	int				id;
 	enum dw_edma_dir		dir;
 
@@ -109,10 +95,6 @@ struct dw_edma_irq {
 	struct dw_edma			*dw;
 };
 
-struct dw_edma_core_ops {
-	int	(*irq_vector)(struct device *dev, unsigned int nr);
-};
-
 struct dw_edma {
 	char				name[20];
 
@@ -122,21 +104,14 @@ struct dw_edma {
 	struct dma_device		rd_edma;
 	u16				rd_ch_cnt;
 
-	struct dw_edma_region		rg_region;	/* Registers */
-	struct dw_edma_region		ll_region_wr[EDMA_MAX_WR_CH];
-	struct dw_edma_region		ll_region_rd[EDMA_MAX_RD_CH];
-	struct dw_edma_region		dt_region_wr[EDMA_MAX_WR_CH];
-	struct dw_edma_region		dt_region_rd[EDMA_MAX_RD_CH];
-
 	struct dw_edma_irq		*irq;
 	int				nr_irqs;
 
-	enum dw_edma_map_format		mf;
-
 	struct dw_edma_chan		*chan;
-	const struct dw_edma_core_ops	*ops;
 
 	raw_spinlock_t			lock;		/* Only for legacy */
+
+	struct dw_edma_chip             *chip;
 #ifdef CONFIG_DEBUG_FS
 	struct dentry			*debugfs;
 #endif /* CONFIG_DEBUG_FS */
drivers/dma/dw-edma/dw-edma-pcie.c +34 -48
index b8f52ca10fa91..2c1c5fa4e9f28 100644
@@ -148,7 +148,6 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	struct dw_edma_pcie_data vsec_data;
 	struct device *dev = &pdev->dev;
 	struct dw_edma_chip *chip;
-	struct dw_edma *dw;
 	int err, nr_irqs;
 	int i, mask;
 
@@ -214,10 +213,6 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	if (!chip)
 		return -ENOMEM;
 
-	dw = devm_kzalloc(dev, sizeof(*dw), GFP_KERNEL);
-	if (!dw)
-		return -ENOMEM;
-
 	/* IRQs allocation */
 	nr_irqs = pci_alloc_irq_vectors(pdev, 1, vsec_data.irqs,
 					PCI_IRQ_MSI | PCI_IRQ_MSIX);
@@ -228,28 +223,23 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	}
 
 	/* Data structure initialization */
-	chip->dw = dw;
 	chip->dev = dev;
 	chip->id = pdev->devfn;
 
-	dw->mf = vsec_data.mf;
-	dw->nr_irqs = nr_irqs;
-	dw->ops = &dw_edma_pcie_core_ops;
-	dw->wr_ch_cnt = vsec_data.wr_ch_cnt;
-	dw->rd_ch_cnt = vsec_data.rd_ch_cnt;
+	chip->mf = vsec_data.mf;
+	chip->nr_irqs = nr_irqs;
+	chip->ops = &dw_edma_pcie_core_ops;
 
-	dw->rg_region.vaddr = pcim_iomap_table(pdev)[vsec_data.rg.bar];
-	if (!dw->rg_region.vaddr)
-		return -ENOMEM;
+	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
+	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
 
-	dw->rg_region.vaddr += vsec_data.rg.off;
-	dw->rg_region.paddr = pdev->resource[vsec_data.rg.bar].start;
-	dw->rg_region.paddr += vsec_data.rg.off;
-	dw->rg_region.sz = vsec_data.rg.sz;
+	chip->rg_region.vaddr = pcim_iomap_table(pdev)[vsec_data.rg.bar];
+	if (!chip->rg_region.vaddr)
+		return -ENOMEM;
 
-	for (i = 0; i < dw->wr_ch_cnt; i++) {
-		struct dw_edma_region *ll_region = &dw->ll_region_wr[i];
-		struct dw_edma_region *dt_region = &dw->dt_region_wr[i];
+	for (i = 0; i < chip->wr_ch_cnt; i++) {
+		struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
+		struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
 		struct dw_edma_block *dt_block = &vsec_data.dt_wr[i];
 
@@ -272,9 +262,9 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		dt_region->sz = dt_block->sz;
 	}
 
-	for (i = 0; i < dw->rd_ch_cnt; i++) {
-		struct dw_edma_region *ll_region = &dw->ll_region_rd[i];
-		struct dw_edma_region *dt_region = &dw->dt_region_rd[i];
+	for (i = 0; i < chip->rd_ch_cnt; i++) {
+		struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
+		struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
 		struct dw_edma_block *dt_block = &vsec_data.dt_rd[i];
 
@@ -298,45 +288,45 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	}
 
 	/* Debug info */
-	if (dw->mf == EDMA_MF_EDMA_LEGACY)
-		pci_dbg(pdev, "Version:\teDMA Port Logic (0x%x)\n", dw->mf);
-	else if (dw->mf == EDMA_MF_EDMA_UNROLL)
-		pci_dbg(pdev, "Version:\teDMA Unroll (0x%x)\n", dw->mf);
-	else if (dw->mf == EDMA_MF_HDMA_COMPAT)
-		pci_dbg(pdev, "Version:\tHDMA Compatible (0x%x)\n", dw->mf);
+	if (chip->mf == EDMA_MF_EDMA_LEGACY)
+		pci_dbg(pdev, "Version:\teDMA Port Logic (0x%x)\n", chip->mf);
+	else if (chip->mf == EDMA_MF_EDMA_UNROLL)
+		pci_dbg(pdev, "Version:\teDMA Unroll (0x%x)\n", chip->mf);
+	else if (chip->mf == EDMA_MF_HDMA_COMPAT)
+		pci_dbg(pdev, "Version:\tHDMA Compatible (0x%x)\n", chip->mf);
 	else
-		pci_dbg(pdev, "Version:\tUnknown (0x%x)\n", dw->mf);
+		pci_dbg(pdev, "Version:\tUnknown (0x%x)\n", chip->mf);
 
-	pci_dbg(pdev, "Registers:\tBAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
+	pci_dbg(pdev, "Registers:\tBAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p)\n",
 		vsec_data.rg.bar, vsec_data.rg.off, vsec_data.rg.sz,
-		dw->rg_region.vaddr, &dw->rg_region.paddr);
+		chip->rg_region.vaddr);
 
 
-	for (i = 0; i < dw->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->wr_ch_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_wr[i].bar,
-			vsec_data.ll_wr[i].off, dw->ll_region_wr[i].sz,
-			dw->ll_region_wr[i].vaddr, &dw->ll_region_wr[i].paddr);
+			vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
+			chip->ll_region_wr[i].vaddr, &chip->ll_region_wr[i].paddr);
 
 		pci_dbg(pdev, "Data:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.dt_wr[i].bar,
-			vsec_data.dt_wr[i].off, dw->dt_region_wr[i].sz,
-			dw->dt_region_wr[i].vaddr, &dw->dt_region_wr[i].paddr);
+			vsec_data.dt_wr[i].off, chip->dt_region_wr[i].sz,
+			chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
 	}
 
-	for (i = 0; i < dw->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->rd_ch_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_rd[i].bar,
-			vsec_data.ll_rd[i].off, dw->ll_region_rd[i].sz,
-			dw->ll_region_rd[i].vaddr, &dw->ll_region_rd[i].paddr);
+			vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
+			chip->ll_region_rd[i].vaddr, &chip->ll_region_rd[i].paddr);
 
 		pci_dbg(pdev, "Data:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.dt_rd[i].bar,
-			vsec_data.dt_rd[i].off, dw->dt_region_rd[i].sz,
-			dw->dt_region_rd[i].vaddr, &dw->dt_region_rd[i].paddr);
+			vsec_data.dt_rd[i].off, chip->dt_region_rd[i].sz,
+			chip->dt_region_rd[i].vaddr, &chip->dt_region_rd[i].paddr);
 	}
 
-	pci_dbg(pdev, "Nr. IRQs:\t%u\n", dw->nr_irqs);
+	pci_dbg(pdev, "Nr. IRQs:\t%u\n", chip->nr_irqs);
 
 	/* Validating if PCI interrupts were enabled */
 	if (!pci_dev_msi_enabled(pdev)) {
@@ -344,10 +334,6 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		return -EPERM;
 	}
 
-	dw->irq = devm_kcalloc(dev, nr_irqs, sizeof(*dw->irq), GFP_KERNEL);
-	if (!dw->irq)
-		return -ENOMEM;
-
 	/* Starting eDMA driver */
 	err = dw_edma_probe(chip);
 	if (err) {
drivers/dma/dw-edma/dw-edma-v0-core.c +16 -16
index 329fc2e57b703..6cf6c28ce0cc9 100644
@@ -25,7 +25,7 @@ enum dw_edma_control {
 
 static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 {
-	return dw->rg_region.vaddr;
+	return dw->chip->rg_region.vaddr;
 }
 
 #define SET_32(dw, name, value)				\
@@ -96,7 +96,7 @@ static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 static inline struct dw_edma_v0_ch_regs __iomem *
 __dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY)
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY)
 		return &(__dw_regs(dw)->type.legacy.ch);
 
 	if (dir == EDMA_DIR_WRITE)
@@ -108,7 +108,7 @@ __dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
 static inline void writel_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			     u32 value, void __iomem *addr)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -133,7 +133,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 {
 	u32 value;
 
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -169,7 +169,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 static inline void writeq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			     u64 value, void __iomem *addr)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -194,7 +194,7 @@ static inline u64 readq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 {
 	u32 value;
 
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -256,7 +256,7 @@ u16 dw_edma_v0_core_ch_count(struct dw_edma *dw, enum dw_edma_dir dir)
 
 enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp;
 
 	tmp = FIELD_GET(EDMA_V0_CH_STATUS_MASK,
@@ -272,7 +272,7 @@ enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)
 
 void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 
 	SET_RW_32(dw, chan->dir, int_clear,
 		  FIELD_PREP(EDMA_V0_DONE_INT_MASK, BIT(chan->id)));
@@ -280,7 +280,7 @@ void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan)
 
 void dw_edma_v0_core_clear_abort_int(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 
 	SET_RW_32(dw, chan->dir, int_clear,
 		  FIELD_PREP(EDMA_V0_ABORT_INT_MASK, BIT(chan->id)));
@@ -357,7 +357,7 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 {
 	struct dw_edma_chan *chan = chunk->chan;
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp;
 
 	dw_edma_v0_core_write_chunk(chunk);
@@ -365,7 +365,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 	if (first) {
 		/* Enable engine */
 		SET_RW_32(dw, chan->dir, engine_en, BIT(0));
-		if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+		if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 			switch (chan->id) {
 			case 0:
 				SET_RW_COMPAT(dw, chan->dir, ch0_pwr_en,
@@ -431,7 +431,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 
 int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp = 0;
 
 	/* MSI done addr - low, high */
@@ -501,12 +501,12 @@ int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)
 }
 
 /* eDMA debugfs callbacks */
-void dw_edma_v0_core_debugfs_on(struct dw_edma_chip *chip)
+void dw_edma_v0_core_debugfs_on(struct dw_edma *dw)
 {
-	dw_edma_v0_debugfs_on(chip);
+	dw_edma_v0_debugfs_on(dw);
 }
 
-void dw_edma_v0_core_debugfs_off(struct dw_edma_chip *chip)
+void dw_edma_v0_core_debugfs_off(struct dw_edma *dw)
 {
-	dw_edma_v0_debugfs_off(chip);
+	dw_edma_v0_debugfs_off(dw);
 }
drivers/dma/dw-edma/dw-edma-v0-core.h +2 -2
index 2afa626b8300c..75aec6d31b210 100644
@@ -22,7 +22,7 @@ u32 dw_edma_v0_core_status_abort_int(struct dw_edma *chan, enum dw_edma_dir dir)
 void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first);
 int dw_edma_v0_core_device_config(struct dw_edma_chan *chan);
 /* eDMA debug fs callbacks */
-void dw_edma_v0_core_debugfs_on(struct dw_edma_chip *chip);
-void dw_edma_v0_core_debugfs_off(struct dw_edma_chip *chip);
+void dw_edma_v0_core_debugfs_on(struct dw_edma *dw);
+void dw_edma_v0_core_debugfs_off(struct dw_edma *dw);
 
 #endif /* _DW_EDMA_V0_CORE_H */
drivers/dma/dw-edma/dw-edma-v0-debugfs.c +9 -9
index 4b3bcffd15ef1..b765adb969998 100644
@@ -54,7 +54,7 @@ struct debugfs_entries {
 static int dw_edma_debugfs_u32_get(void *data, u64 *val)
 {
 	void __iomem *reg = (void __force __iomem *)data;
-	if (dw->mf == EDMA_MF_EDMA_LEGACY &&
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY &&
 	    reg >= (void __iomem *)&regs->type.legacy.ch) {
 		void __iomem *ptr = &regs->type.legacy.ch;
 		u32 viewport_sel = 0;
@@ -173,7 +173,7 @@ static void dw_edma_debugfs_regs_wr(struct dentry *dir)
 	nr_entries = ARRAY_SIZE(debugfs_regs);
 	dw_edma_debugfs_create_x32(debugfs_regs, nr_entries, regs_dir);
 
-	if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+	if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 		nr_entries = ARRAY_SIZE(debugfs_unroll_regs);
 		dw_edma_debugfs_create_x32(debugfs_unroll_regs, nr_entries,
 					   regs_dir);
@@ -242,7 +242,7 @@ static void dw_edma_debugfs_regs_rd(struct dentry *dir)
 	nr_entries = ARRAY_SIZE(debugfs_regs);
 	dw_edma_debugfs_create_x32(debugfs_regs, nr_entries, regs_dir);
 
-	if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+	if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 		nr_entries = ARRAY_SIZE(debugfs_unroll_regs);
 		dw_edma_debugfs_create_x32(debugfs_unroll_regs, nr_entries,
 					   regs_dir);
@@ -282,13 +282,13 @@ static void dw_edma_debugfs_regs(void)
 	dw_edma_debugfs_regs_rd(regs_dir);
 }
 
-void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
+void dw_edma_v0_debugfs_on(struct dw_edma *_dw)
 {
-	dw = chip->dw;
+	dw = _dw;
 	if (!dw)
 		return;
 
-	regs = dw->rg_region.vaddr;
+	regs = dw->chip->rg_region.vaddr;
 	if (!regs)
 		return;
 
@@ -296,16 +296,16 @@ void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
 	if (!dw->debugfs)
 		return;
 
-	debugfs_create_u32("mf", 0444, dw->debugfs, &dw->mf);
+	debugfs_create_u32("mf", 0444, dw->debugfs, &dw->chip->mf);
 	debugfs_create_u16("wr_ch_cnt", 0444, dw->debugfs, &dw->wr_ch_cnt);
 	debugfs_create_u16("rd_ch_cnt", 0444, dw->debugfs, &dw->rd_ch_cnt);
 
 	dw_edma_debugfs_regs();
 }
 
-void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip)
+void dw_edma_v0_debugfs_off(struct dw_edma *_dw)
 {
-	dw = chip->dw;
+	dw = _dw;
 	if (!dw)
 		return;
 
drivers/dma/dw-edma/dw-edma-v0-debugfs.h +4 -4
index d0ff25a9ea5c9..3391b86edf5ab 100644
@@ -12,14 +12,14 @@
 #include <linux/dma/edma.h>
 
 #ifdef CONFIG_DEBUG_FS
-void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip);
-void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip);
+void dw_edma_v0_debugfs_on(struct dw_edma *dw);
+void dw_edma_v0_debugfs_off(struct dw_edma *dw);
 #else
-static inline void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
+static inline void dw_edma_v0_debugfs_on(struct dw_edma *dw)
 {
 }
 
-static inline void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip)
+static inline void dw_edma_v0_debugfs_off(struct dw_edma *dw)
 {
 }
 #endif /* CONFIG_DEBUG_FS */
include/linux/dma/edma.h +44 -0
index d4333e721588d..6fd374cc72c8e 100644
@@ -12,17 +12,61 @@
 #include <linux/device.h>
 #include <linux/dmaengine.h>
 
+#define EDMA_MAX_WR_CH                                  8
+#define EDMA_MAX_RD_CH                                  8
+
 struct dw_edma;
 
+struct dw_edma_region {
+	phys_addr_t	paddr;
+	void __iomem	*vaddr;
+	size_t		sz;
+};
+
+struct dw_edma_core_ops {
+	int (*irq_vector)(struct device *dev, unsigned int nr);
+};
+
+enum dw_edma_map_format {
+	EDMA_MF_EDMA_LEGACY = 0x0,
+	EDMA_MF_EDMA_UNROLL = 0x1,
+	EDMA_MF_HDMA_COMPAT = 0x5
+};
+
 /**
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
+ * @nr_irqs:		 total dma irq number
+ * @ops			 DMA channel to IRQ number mapping
+ * @wr_ch_cnt		 DMA write channel number
+ * @rd_ch_cnt		 DMA read channel number
+ * @rg_region		 DMA register region
+ * @ll_region_wr	 DMA descriptor link list memory for write channel
+ * @ll_region_rd	 DMA descriptor link list memory for read channel
+ * @mf			 DMA register map format
  * @dw:			 struct dw_edma that is filed by dw_edma_probe()
  */
 struct dw_edma_chip {
 	struct device		*dev;
 	int			id;
+	int			nr_irqs;
+	const struct dw_edma_core_ops   *ops;
+
+	struct dw_edma_region	rg_region;
+
+	u16			wr_ch_cnt;
+	u16			rd_ch_cnt;
+	/* link list address */
+	struct dw_edma_region	ll_region_wr[EDMA_MAX_WR_CH];
+	struct dw_edma_region	ll_region_rd[EDMA_MAX_RD_CH];
+
+	/* data region */
+	struct dw_edma_region	dt_region_wr[EDMA_MAX_WR_CH];
+	struct dw_edma_region	dt_region_rd[EDMA_MAX_RD_CH];
+
+	enum dw_edma_map_format	mf;
+
 	struct dw_edma		*dw;
 };
 
Signature · 1 line
2.35.1
Reviewed-by on v9 2/9
#5 lore raw

Re: [PATCH v9 2/9] dmaengine: dw-edma: Detach the private data and chip info structures

In reply to Frank Li
Quoted 11 lines · Frank Li

"struct dw_edma_chip" contains an internal structure "struct dw_edma" that is used by the eDMA core internally. This structure should not be touched by the eDMA controller drivers themselves. But currently, the eDMA controller drivers like "dw-edma-pci" allocates and populates this internal structure then passes it on to eDMA core. The eDMA core further populates the structure and uses it. This is wrong!

Hence, move all the "struct dw_edma" specifics from controller drivers to the eDMA core.

There is a comment below, but other that that:

Quoted 40 lines

---
Change from v8 to v9
- remove chip->ops check at dw_edma_irq_request()
Change from v7 to v8
- Check chip->ops at probe()
- use struct edma_dw at dw_edma_v0_debugfs_on/off()

Change from v6 to v7
- Move nr_irqs and chip->ops check into dw_edma_irq_request()
- Move dw->irq devm_kcalloc() into dw_edma_irq_request()
- Change dw->nr_irqs after request success
- Fix wrong use chip->nr_irqs when remove

Change from v5 to v6
- Don't touch chip->nr_irqs
- Don't set chip->dw utill everything is okay
- dw_edma_channel_setup() and dw_edma_v0_core_debugfs_on/off() methods take dw_edma structure pointer as a parameter

Change from v4 to v5
- Move chip->nr_irqs before allocate dw_edma
Change from v3 to v4
- Accept most suggestions of Serge Semin
Change from v2 to v3
- none
Change from v1 to v2
- rework commit message
- remove duplicate field in struct dw_edma

 drivers/dma/dw-edma/dw-edma-core.c       | 90 +++++++++++++-----------
 drivers/dma/dw-edma/dw-edma-core.h       | 31 +-------
 drivers/dma/dw-edma/dw-edma-pcie.c       | 82 +++++++++------------
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 32 ++++-----
 drivers/dma/dw-edma/dw-edma-v0-core.h    |  4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 18 ++---
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h |  8 +--
 include/linux/dma/edma.h                 | 44 ++++++++++++
 8 files changed, 161 insertions(+), 148 deletions(-)

[...]

Quoted 31 lines
include/linux/dma/edma.h +19 -0
index d4333e721588d..6fd374cc72c8e 100644
@@ -12,17 +12,61 @@
 #include <linux/device.h>
 #include <linux/dmaengine.h>
 
+#define EDMA_MAX_WR_CH                                  8
+#define EDMA_MAX_RD_CH                                  8
+
 struct dw_edma;
 
+struct dw_edma_region {
+	phys_addr_t	paddr;
+	void __iomem	*vaddr;
+	size_t		sz;
+};
+
+struct dw_edma_core_ops {
+	int (*irq_vector)(struct device *dev, unsigned int nr);
+};
+
+enum dw_edma_map_format {
+	EDMA_MF_EDMA_LEGACY = 0x0,
+	EDMA_MF_EDMA_UNROLL = 0x1,
+	EDMA_MF_HDMA_COMPAT = 0x5
+};
+
 /**
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware

include/linux/dma/edma.h line 47

Quoted 10 lines
include/linux/dma/edma.h +8 -0
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
+ * @nr_irqs:		 total dma irq number
+ * @ops			 DMA channel to IRQ number mapping
+ * @wr_ch_cnt		 DMA write channel number
+ * @rd_ch_cnt		 DMA read channel number
+ * @rg_region		 DMA register region
+ * @ll_region_wr	 DMA descriptor link list memory for write channel
+ * @ll_region_rd	 DMA descriptor link list memory for read channel
+ * @mf			 DMA register map format

Not all members added below are documented in kdoc. Please fix.

Thanks,
Mani

Quoted 28 lines
include/linux/dma/edma.h +17 -0
  * @dw:			 struct dw_edma that is filed by dw_edma_probe()
  */
 struct dw_edma_chip {
 	struct device		*dev;
 	int			id;
+	int			nr_irqs;
+	const struct dw_edma_core_ops   *ops;
+
+	struct dw_edma_region	rg_region;
+
+	u16			wr_ch_cnt;
+	u16			rd_ch_cnt;
+	/* link list address */
+	struct dw_edma_region	ll_region_wr[EDMA_MAX_WR_CH];
+	struct dw_edma_region	ll_region_rd[EDMA_MAX_RD_CH];
+
+	/* data region */
+	struct dw_edma_region	dt_region_wr[EDMA_MAX_WR_CH];
+	struct dw_edma_region	dt_region_rd[EDMA_MAX_RD_CH];
+
+	enum dw_edma_map_format	mf;
+
 	struct dw_edma		*dw;
 };
 
Signature · 1 line
2.35.1
author
#6 lore raw

PATCH v9 3/9 dmaengine: dw-edma: Change rg_region to reg_base in struct dw_edma_chip

In reply to Frank Li

struct dw_edma_region rg_region included virtual address, physical address and size informaiton. But only virtual address is used by EDMA driver. Change it to void __iomem *reg_base to clean up code.

---
Change from v6 to v9:
- none
Change from v5 to v6:
-s/change/Change at subject
New patch at v4

 drivers/dma/dw-edma/dw-edma-pcie.c       | 6 +++---
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 2 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 2 +-
 include/linux/dma/edma.h                 | 3 ++-
 4 files changed, 7 insertions(+), 6 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +3 -3
index 2c1c5fa4e9f28..ae42bad24dd5a 100644
@@ -233,8 +233,8 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
 	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
 
-	chip->rg_region.vaddr = pcim_iomap_table(pdev)[vsec_data.rg.bar];
-	if (!chip->rg_region.vaddr)
+	chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
+	if (!chip->reg_base)
 		return -ENOMEM;
 
 	for (i = 0; i < chip->wr_ch_cnt; i++) {
@@ -299,7 +299,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 
 	pci_dbg(pdev, "Registers:\tBAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p)\n",
 		vsec_data.rg.bar, vsec_data.rg.off, vsec_data.rg.sz,
-		chip->rg_region.vaddr);
+		chip->reg_base);
 
 
 	for (i = 0; i < chip->wr_ch_cnt; i++) {
drivers/dma/dw-edma/dw-edma-v0-core.c +1 -1
index 6cf6c28ce0cc9..c59e23b9f9fdb 100644
@@ -25,7 +25,7 @@ enum dw_edma_control {
 
 static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 {
-	return dw->chip->rg_region.vaddr;
+	return dw->chip->reg_base;
 }
 
 #define SET_32(dw, name, value)				\
drivers/dma/dw-edma/dw-edma-v0-debugfs.c +1 -1
index da88958399a95..f59e7c37feac3 100644
@@ -287,7 +287,7 @@ void dw_edma_v0_debugfs_on(struct dw_edma *dw)
 	if (!dw)
 		return;
 
-	regs = dw->chip->rg_region.vaddr;
+	regs = dw->chip->reg_base;
 	if (!regs)
 		return;
 
include/linux/dma/edma.h +2 -1
index 6fd374cc72c8e..e9ce652b88233 100644
@@ -39,6 +39,7 @@ enum dw_edma_map_format {
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @reg_base		 DMA register base address
  * @wr_ch_cnt		 DMA write channel number
  * @rd_ch_cnt		 DMA read channel number
  * @rg_region		 DMA register region
@@ -53,7 +54,7 @@ struct dw_edma_chip {
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
 
-	struct dw_edma_region	rg_region;
+	void __iomem		*reg_base;
 
 	u16			wr_ch_cnt;
 	u16			rd_ch_cnt;
Signature · 1 line
2.35.1
Reviewed-by on v9 3/9
#7 lore raw

Re: [PATCH v9 3/9] dmaengine: dw-edma: Change rg_region to reg_base in struct dw_edma_chip

Quoted 2 lines · Frank Li

struct dw_edma_region rg_region included virtual address, physical address and size informaiton. But only virtual address is used by EDMA

information

Quoted 3 lines

driver. Change it to void __iomem *reg_base to clean up code.

Thanks,
Mani

Quoted 89 lines

---
Change from v6 to v9:
- none
Change from v5 to v6:
-s/change/Change at subject
New patch at v4

 drivers/dma/dw-edma/dw-edma-pcie.c       | 6 +++---
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 2 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 2 +-
 include/linux/dma/edma.h                 | 3 ++-
 4 files changed, 7 insertions(+), 6 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +3 -3
index 2c1c5fa4e9f28..ae42bad24dd5a 100644
@@ -233,8 +233,8 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
 	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
 
-	chip->rg_region.vaddr = pcim_iomap_table(pdev)[vsec_data.rg.bar];
-	if (!chip->rg_region.vaddr)
+	chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
+	if (!chip->reg_base)
 		return -ENOMEM;
 
 	for (i = 0; i < chip->wr_ch_cnt; i++) {
@@ -299,7 +299,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 
 	pci_dbg(pdev, "Registers:\tBAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p)\n",
 		vsec_data.rg.bar, vsec_data.rg.off, vsec_data.rg.sz,
-		chip->rg_region.vaddr);
+		chip->reg_base);
 
 
 	for (i = 0; i < chip->wr_ch_cnt; i++) {
drivers/dma/dw-edma/dw-edma-v0-core.c +1 -1
index 6cf6c28ce0cc9..c59e23b9f9fdb 100644
@@ -25,7 +25,7 @@ enum dw_edma_control {
 
 static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 {
-	return dw->chip->rg_region.vaddr;
+	return dw->chip->reg_base;
 }
 
 #define SET_32(dw, name, value)				\
drivers/dma/dw-edma/dw-edma-v0-debugfs.c +1 -1
index da88958399a95..f59e7c37feac3 100644
@@ -287,7 +287,7 @@ void dw_edma_v0_debugfs_on(struct dw_edma *dw)
 	if (!dw)
 		return;
 
-	regs = dw->chip->rg_region.vaddr;
+	regs = dw->chip->reg_base;
 	if (!regs)
 		return;
 
include/linux/dma/edma.h +2 -1
index 6fd374cc72c8e..e9ce652b88233 100644
@@ -39,6 +39,7 @@ enum dw_edma_map_format {
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @reg_base		 DMA register base address
  * @wr_ch_cnt		 DMA write channel number
  * @rd_ch_cnt		 DMA read channel number
  * @rg_region		 DMA register region
@@ -53,7 +54,7 @@ struct dw_edma_chip {
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
 
-	struct dw_edma_region	rg_region;
+	void __iomem		*reg_base;
 
 	u16			wr_ch_cnt;
 	u16			rd_ch_cnt;
Signature · 1 line
2.35.1
author
#8 lore raw

PATCH v9 4/9 dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

In reply to Frank Li

There are same name wr(rd)_ch_cnt in struct dw_edma. EDMA driver get write(read) channel number from register, then save these into dw_edma. Old wr(rd)_ch_cnt in dw_edma_chip actuall means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. So rename it to ll_wr(rd)_cnt to indicate actual usage.

---
Change from v6 to v9
- none
Change from v5 to v6
- s/rename/Rename/ at subject
new patch at v4

 drivers/dma/dw-edma/dw-edma-core.c |  4 ++--
 drivers/dma/dw-edma/dw-edma-pcie.c | 12 ++++++------
 include/linux/dma/edma.h           |  8 ++++----
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +2 -2
index 435e4f2ab6575..1a0a98f6c5515 100644
@@ -919,11 +919,11 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 
 	raw_spin_lock_init(&dw->lock);
 
-	dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
+	dw->wr_ch_cnt = min_t(u16, chip->ll_wr_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
 	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-	dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
+	dw->rd_ch_cnt = min_t(u16, chip->ll_rd_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
 	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
drivers/dma/dw-edma/dw-edma-pcie.c +6 -6
index ae42bad24dd5a..7732537f96086 100644
@@ -230,14 +230,14 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->nr_irqs = nr_irqs;
 	chip->ops = &dw_edma_pcie_core_ops;
 
-	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
-	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
+	chip->ll_wr_cnt = vsec_data.wr_ch_cnt;
+	chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
 
 	chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
 	if (!chip->reg_base)
 		return -ENOMEM;
 
-	for (i = 0; i < chip->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_wr_cnt; i++) {
 		struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
 		struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
@@ -262,7 +262,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		dt_region->sz = dt_block->sz;
 	}
 
-	for (i = 0; i < chip->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_rd_cnt; i++) {
 		struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
 		struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
@@ -302,7 +302,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		chip->reg_base);
 
 
-	for (i = 0; i < chip->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_wr_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_wr[i].bar,
 			vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
@@ -314,7 +314,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 			chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
 	}
 
-	for (i = 0; i < chip->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_rd_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_rd[i].bar,
 			vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
include/linux/dma/edma.h +4 -4
index e9ce652b88233..c2039246fc08c 100644
@@ -40,8 +40,8 @@ enum dw_edma_map_format {
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
  * @reg_base		 DMA register base address
- * @wr_ch_cnt		 DMA write channel number
- * @rd_ch_cnt		 DMA read channel number
+ * @ll_wr_cnt		 DMA write link list number
+ * @ll_rd_cnt		 DMA read link list number
  * @rg_region		 DMA register region
  * @ll_region_wr	 DMA descriptor link list memory for write channel
  * @ll_region_rd	 DMA descriptor link list memory for read channel
@@ -56,8 +56,8 @@ struct dw_edma_chip {
 
 	void __iomem		*reg_base;
 
-	u16			wr_ch_cnt;
-	u16			rd_ch_cnt;
+	u16			ll_wr_cnt;
+	u16			ll_rd_cnt;
 	/* link list address */
 	struct dw_edma_region	ll_region_wr[EDMA_MAX_WR_CH];
 	struct dw_edma_region	ll_region_rd[EDMA_MAX_RD_CH];
Signature · 1 line
2.35.1
Reviewed-by on v9 4/9
#9 lore raw

Re: [PATCH v9 4/9] dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

Quoted 7 lines · Frank Li

There are same name wr(rd)_ch_cnt in struct dw_edma. EDMA driver get write(read) channel number from register, then save these into dw_edma. Old wr(rd)_ch_cnt in dw_edma_chip actuall means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. So rename it to ll_wr(rd)_cnt to indicate actual usage.

One minor comment below,

Quoted 85 lines

---
Change from v6 to v9
- none
Change from v5 to v6
- s/rename/Rename/ at subject
new patch at v4

 drivers/dma/dw-edma/dw-edma-core.c |  4 ++--
 drivers/dma/dw-edma/dw-edma-pcie.c | 12 ++++++------
 include/linux/dma/edma.h           |  8 ++++----
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +2 -2
index 435e4f2ab6575..1a0a98f6c5515 100644
@@ -919,11 +919,11 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 
 	raw_spin_lock_init(&dw->lock);
 
-	dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
+	dw->wr_ch_cnt = min_t(u16, chip->ll_wr_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
 	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-	dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
+	dw->rd_ch_cnt = min_t(u16, chip->ll_rd_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
 	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
drivers/dma/dw-edma/dw-edma-pcie.c +6 -6
index ae42bad24dd5a..7732537f96086 100644
@@ -230,14 +230,14 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->nr_irqs = nr_irqs;
 	chip->ops = &dw_edma_pcie_core_ops;
 
-	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
-	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
+	chip->ll_wr_cnt = vsec_data.wr_ch_cnt;
+	chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
 
 	chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
 	if (!chip->reg_base)
 		return -ENOMEM;
 
-	for (i = 0; i < chip->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_wr_cnt; i++) {
 		struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
 		struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
@@ -262,7 +262,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		dt_region->sz = dt_block->sz;
 	}
 
-	for (i = 0; i < chip->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_rd_cnt; i++) {
 		struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
 		struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
@@ -302,7 +302,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		chip->reg_base);
 
 
-	for (i = 0; i < chip->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_wr_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_wr[i].bar,
 			vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
@@ -314,7 +314,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 			chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
 	}
 
-	for (i = 0; i < chip->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_rd_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_rd[i].bar,
 			vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
include/linux/dma/edma.h +0 -0
index e9ce652b88233..c2039246fc08c 100644

include/linux/dma/edma.h enum dw_edma_map_format { · line 44

Quoted 7 lines
include/linux/dma/edma.h +2 -2
@@ -40,8 +40,8 @@ enum dw_edma_map_format {
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
  * @reg_base		 DMA register base address
- * @wr_ch_cnt		 DMA write channel number
- * @rd_ch_cnt		 DMA read channel number
+ * @ll_wr_cnt		 DMA write link list number
+ * @ll_rd_cnt		 DMA read link list number

DMA linked list write/read memory regions?

Thanks,
Mani

Quoted 17 lines
include/linux/dma/edma.h +2 -2
  * @rg_region		 DMA register region
  * @ll_region_wr	 DMA descriptor link list memory for write channel
  * @ll_region_rd	 DMA descriptor link list memory for read channel
@@ -56,8 +56,8 @@ struct dw_edma_chip {
 
 	void __iomem		*reg_base;
 
-	u16			wr_ch_cnt;
-	u16			rd_ch_cnt;
+	u16			ll_wr_cnt;
+	u16			ll_rd_cnt;
 	/* link list address */
 	struct dw_edma_region	ll_region_wr[EDMA_MAX_WR_CH];
 	struct dw_edma_region	ll_region_rd[EDMA_MAX_RD_CH];
Signature · 1 line
2.35.1
#10 lore raw

Re: [PATCH v9 4/9] dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

Quoted 100 lines · Manivannan Sadhasivam
Quoted 7 lines · Frank Li

There are same name wr(rd)_ch_cnt in struct dw_edma. EDMA driver get write(read) channel number from register, then save these into dw_edma. Old wr(rd)_ch_cnt in dw_edma_chip actuall means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. So rename it to ll_wr(rd)_cnt to indicate actual usage.

One minor comment below,

Quoted 86 lines

---
Change from v6 to v9
- none
Change from v5 to v6
- s/rename/Rename/ at subject
new patch at v4

 drivers/dma/dw-edma/dw-edma-core.c |  4 ++--
 drivers/dma/dw-edma/dw-edma-pcie.c | 12 ++++++------
 include/linux/dma/edma.h           |  8 ++++----
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +2 -2
index 435e4f2ab6575..1a0a98f6c5515 100644
@@ -919,11 +919,11 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 
      raw_spin_lock_init(&dw->lock);
 
-     dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
+     dw->wr_ch_cnt = min_t(u16, chip->ll_wr_cnt,
                            dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
      dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-     dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
+     dw->rd_ch_cnt = min_t(u16, chip->ll_rd_cnt,
                            dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
      dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
drivers/dma/dw-edma/dw-edma-pcie.c +6 -6
index ae42bad24dd5a..7732537f96086 100644
@@ -230,14 +230,14 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
      chip->nr_irqs = nr_irqs;
      chip->ops = &dw_edma_pcie_core_ops;
 
-     chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
-     chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
+     chip->ll_wr_cnt = vsec_data.wr_ch_cnt;
+     chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
 
      chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
      if (!chip->reg_base)
              return -ENOMEM;
 
-     for (i = 0; i < chip->wr_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_wr_cnt; i++) {
              struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
              struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
              struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
@@ -262,7 +262,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
              dt_region->sz = dt_block->sz;
      }
 
-     for (i = 0; i < chip->rd_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_rd_cnt; i++) {
              struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
              struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
              struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
@@ -302,7 +302,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
              chip->reg_base);
 
 
-     for (i = 0; i < chip->wr_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_wr_cnt; i++) {
              pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
                      i, vsec_data.ll_wr[i].bar,
                      vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
@@ -314,7 +314,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
                      chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
      }
 
-     for (i = 0; i < chip->rd_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_rd_cnt; i++) {
              pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
                      i, vsec_data.ll_rd[i].bar,
                      vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
include/linux/dma/edma.h +0 -0
index e9ce652b88233..c2039246fc08c 100644
@@ -40,8 +40,8 @@ enum dw_edma_map_format {
  * @nr_irqs:          total dma irq number
Quoted 8 lines

include/linux/dma/edma.h enum dw_edma_map_format { · line 44

Quoted 6 lines
include/linux/dma/edma.h +2 -2
  * @ops                       DMA channel to IRQ number mapping
  * @reg_base          DMA register base address
- * @wr_ch_cnt                 DMA write channel number
- * @rd_ch_cnt                 DMA read channel number
+ * @ll_wr_cnt                 DMA write link list number
+ * @ll_rd_cnt                 DMA read link list number

DMA linked list write/read memory regions?

ll_wr_cnt is the counter of the DMA listed list.

Do you means

@ll_region_wr DMA linked list write memory regions

best regards
Frank Li

Quoted 21 lines

Thanks,
Mani

Quoted 17 lines
include/linux/dma/edma.h +2 -3
  * @rg_region                 DMA register region
  * @ll_region_wr      DMA descriptor link list memory for write channel
  * @ll_region_rd      DMA descriptor link list memory for read channel
@@ -56,8 +56,8 @@ struct dw_edma_chip {
 
      void __iomem            *reg_base;
 
-     u16                     wr_ch_cnt;
-     u16                     rd_ch_cnt;
+     u16                     ll_wr_cnt;
+     u16                     ll_rd_cnt;
      /* link list address */
      struct dw_edma_region   ll_region_wr[EDMA_MAX_WR_CH];
      struct dw_edma_region   ll_region_rd[EDMA_MAX_RD_CH];
--

2.35.1

#11 lore raw

Re: [PATCH v9 4/9] dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

Quoted 112 lines · Zhi Li
Quoted 100 lines · Manivannan Sadhasivam
Quoted 7 lines · Frank Li

There are same name wr(rd)_ch_cnt in struct dw_edma. EDMA driver get write(read) channel number from register, then save these into dw_edma. Old wr(rd)_ch_cnt in dw_edma_chip actuall means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. So rename it to ll_wr(rd)_cnt to indicate actual usage.

One minor comment below,

Quoted 86 lines

---
Change from v6 to v9
- none
Change from v5 to v6
- s/rename/Rename/ at subject
new patch at v4

 drivers/dma/dw-edma/dw-edma-core.c |  4 ++--
 drivers/dma/dw-edma/dw-edma-pcie.c | 12 ++++++------
 include/linux/dma/edma.h           |  8 ++++----
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +2 -2
index 435e4f2ab6575..1a0a98f6c5515 100644
@@ -919,11 +919,11 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 
      raw_spin_lock_init(&dw->lock);
 
-     dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
+     dw->wr_ch_cnt = min_t(u16, chip->ll_wr_cnt,
                            dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
      dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-     dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
+     dw->rd_ch_cnt = min_t(u16, chip->ll_rd_cnt,
                            dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
      dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
drivers/dma/dw-edma/dw-edma-pcie.c +6 -6
index ae42bad24dd5a..7732537f96086 100644
@@ -230,14 +230,14 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
      chip->nr_irqs = nr_irqs;
      chip->ops = &dw_edma_pcie_core_ops;
 
-     chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
-     chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
+     chip->ll_wr_cnt = vsec_data.wr_ch_cnt;
+     chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
 
      chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
      if (!chip->reg_base)
              return -ENOMEM;
 
-     for (i = 0; i < chip->wr_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_wr_cnt; i++) {
              struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
              struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
              struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
@@ -262,7 +262,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
              dt_region->sz = dt_block->sz;
      }
 
-     for (i = 0; i < chip->rd_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_rd_cnt; i++) {
              struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
              struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
              struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
@@ -302,7 +302,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
              chip->reg_base);
 
 
-     for (i = 0; i < chip->wr_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_wr_cnt; i++) {
              pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
                      i, vsec_data.ll_wr[i].bar,
                      vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
@@ -314,7 +314,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
                      chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
      }
 
-     for (i = 0; i < chip->rd_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_rd_cnt; i++) {
              pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
                      i, vsec_data.ll_rd[i].bar,
                      vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
include/linux/dma/edma.h +0 -0
index e9ce652b88233..c2039246fc08c 100644
@@ -40,8 +40,8 @@ enum dw_edma_map_format {
  * @nr_irqs:          total dma irq number
Quoted 8 lines

include/linux/dma/edma.h enum dw_edma_map_format { · line 44

Quoted 6 lines
include/linux/dma/edma.h +2 -2
  * @ops                       DMA channel to IRQ number mapping
  * @reg_base          DMA register base address
- * @wr_ch_cnt                 DMA write channel number
- * @rd_ch_cnt                 DMA read channel number
+ * @ll_wr_cnt                 DMA write link list number
+ * @ll_rd_cnt                 DMA read link list number

DMA linked list write/read memory regions?

Quoted 8 lines

ll_wr_cnt is the counter of the DMA listed list.

Do you means

@ll_region_wr DMA linked list write memory regions

best regards
Frank Li

Ping @Manivannan Sadhasivam

Quoted 23 lines
Quoted 23 lines

Thanks,
Mani

Quoted 17 lines
include/linux/dma/edma.h +2 -3
  * @rg_region                 DMA register region
  * @ll_region_wr      DMA descriptor link list memory for write channel
  * @ll_region_rd      DMA descriptor link list memory for read channel
@@ -56,8 +56,8 @@ struct dw_edma_chip {
 
      void __iomem            *reg_base;
 
-     u16                     wr_ch_cnt;
-     u16                     rd_ch_cnt;
+     u16                     ll_wr_cnt;
+     u16                     ll_rd_cnt;
      /* link list address */
      struct dw_edma_region   ll_region_wr[EDMA_MAX_WR_CH];
      struct dw_edma_region   ll_region_rd[EDMA_MAX_RD_CH];
--

2.35.1

#12 lore raw

Re: [PATCH v9 4/9] dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

In reply to Zhi Li
Quoted 111 lines · Zhi Li
Quoted 100 lines · Manivannan Sadhasivam
Quoted 7 lines · Frank Li

There are same name wr(rd)_ch_cnt in struct dw_edma. EDMA driver get write(read) channel number from register, then save these into dw_edma. Old wr(rd)_ch_cnt in dw_edma_chip actuall means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. So rename it to ll_wr(rd)_cnt to indicate actual usage.

One minor comment below,

Quoted 86 lines

---
Change from v6 to v9
- none
Change from v5 to v6
- s/rename/Rename/ at subject
new patch at v4

 drivers/dma/dw-edma/dw-edma-core.c |  4 ++--
 drivers/dma/dw-edma/dw-edma-pcie.c | 12 ++++++------
 include/linux/dma/edma.h           |  8 ++++----
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +2 -2
index 435e4f2ab6575..1a0a98f6c5515 100644
@@ -919,11 +919,11 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 
      raw_spin_lock_init(&dw->lock);
 
-     dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
+     dw->wr_ch_cnt = min_t(u16, chip->ll_wr_cnt,
                            dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
      dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-     dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
+     dw->rd_ch_cnt = min_t(u16, chip->ll_rd_cnt,
                            dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
      dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
drivers/dma/dw-edma/dw-edma-pcie.c +6 -6
index ae42bad24dd5a..7732537f96086 100644
@@ -230,14 +230,14 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
      chip->nr_irqs = nr_irqs;
      chip->ops = &dw_edma_pcie_core_ops;
 
-     chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
-     chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
+     chip->ll_wr_cnt = vsec_data.wr_ch_cnt;
+     chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
 
      chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
      if (!chip->reg_base)
              return -ENOMEM;
 
-     for (i = 0; i < chip->wr_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_wr_cnt; i++) {
              struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
              struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
              struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
@@ -262,7 +262,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
              dt_region->sz = dt_block->sz;
      }
 
-     for (i = 0; i < chip->rd_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_rd_cnt; i++) {
              struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
              struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
              struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
@@ -302,7 +302,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
              chip->reg_base);
 
 
-     for (i = 0; i < chip->wr_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_wr_cnt; i++) {
              pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
                      i, vsec_data.ll_wr[i].bar,
                      vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
@@ -314,7 +314,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
                      chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
      }
 
-     for (i = 0; i < chip->rd_ch_cnt; i++) {
+     for (i = 0; i < chip->ll_rd_cnt; i++) {
              pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
                      i, vsec_data.ll_rd[i].bar,
                      vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
include/linux/dma/edma.h +0 -0
index e9ce652b88233..c2039246fc08c 100644
@@ -40,8 +40,8 @@ enum dw_edma_map_format {
  * @nr_irqs:          total dma irq number
Quoted 8 lines

include/linux/dma/edma.h enum dw_edma_map_format { · line 44

Quoted 6 lines
include/linux/dma/edma.h +2 -2
  * @ops                       DMA channel to IRQ number mapping
  * @reg_base          DMA register base address
- * @wr_ch_cnt                 DMA write channel number
- * @rd_ch_cnt                 DMA read channel number
+ * @ll_wr_cnt                 DMA write link list number
+ * @ll_rd_cnt                 DMA read link list number

DMA linked list write/read memory regions?

Quoted 6 lines

ll_wr_cnt is the counter of the DMA listed list.

Do you means

@ll_region_wr DMA linked list write memory regions

Sorry, I confused the terms here. But can you use "count" instead of "number"?

Thanks,
Mani

Quoted 25 lines

best regards
Frank Li

Quoted 21 lines

Thanks,
Mani

Quoted 17 lines
include/linux/dma/edma.h +2 -3
  * @rg_region                 DMA register region
  * @ll_region_wr      DMA descriptor link list memory for write channel
  * @ll_region_rd      DMA descriptor link list memory for read channel
@@ -56,8 +56,8 @@ struct dw_edma_chip {
 
      void __iomem            *reg_base;
 
-     u16                     wr_ch_cnt;
-     u16                     rd_ch_cnt;
+     u16                     ll_wr_cnt;
+     u16                     ll_rd_cnt;
      /* link list address */
      struct dw_edma_region   ll_region_wr[EDMA_MAX_WR_CH];
      struct dw_edma_region   ll_region_rd[EDMA_MAX_RD_CH];
--

2.35.1

author
#13 lore raw

PATCH v9 5/9 dmaengine: dw-edma: Drop dma_slave_config.direction field usage

In reply to Frank Li

From: Serge Semin <[email protected]>

The dma_slave_config.direction field usage in the DW eDMA driver has been introduced in the commit bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics"). Mainly the change introduced there was correct (indeed DEV_TO_MEM means using RD-channel and MEM_TO_DEV - WR-channel for the case of having eDMA accessed locally from CPU/Application side), but providing an additional MEM_TO_MEM/DEV_TO_DEV-based semantics was quite redundant if not to say potentially harmful (when it comes to removing the denoted field). First of all since the dma_slave_config.direction field has been marked as obsolete (see [1] and the structure dc [2]) and will be discarded in future, using it especially in a non-standard way is discouraged. Secondly in accordance with the commit denoted above the default dw_edma_device_transfer() semantics has been changed despite what it's message said. So claiming that the method was left backward compatible was wrong.

Anyway let's fix the problems denoted above and simplify the dw_edma_device_transfer() method by dropping the parsing of the DMA-channel direction field. Instead of having that implicit dma_slave_config.direction field semantic we can use the recently added DW_EDMA_CHIP_LOCAL flag to distinguish between the local and remote DW eDMA setups thus preserving both cases support. In addition to that an ASCII-figure has been added to clarify the complication out.

[1] Documentation/driver-api/dmaengine/provider.rst
[2] include/linux/dmaengine.h: dma_slave_config.direction

---
 drivers/dma/dw-edma/dw-edma-core.c | 49 +++++++++++++++++++++---------
 1 file changed, 34 insertions(+), 15 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +34 -15
index 1a0a98f6c5515..184622be500b7 100644
@@ -340,21 +340,40 @@ dw_edma_device_transfer(struct dw_edma_transfer *xfer)
 	if (!chan->configured)
 		return NULL;
 
-	switch (chan->config.direction) {
-	case DMA_DEV_TO_MEM: /* local DMA */
-		if (dir == DMA_DEV_TO_MEM && chan->dir == EDMA_DIR_READ)
-			break;
-		return NULL;
-	case DMA_MEM_TO_DEV: /* local DMA */
-		if (dir == DMA_MEM_TO_DEV && chan->dir == EDMA_DIR_WRITE)
-			break;
-		return NULL;
-	default: /* remote DMA */
-		if (dir == DMA_MEM_TO_DEV && chan->dir == EDMA_DIR_READ)
-			break;
-		if (dir == DMA_DEV_TO_MEM && chan->dir == EDMA_DIR_WRITE)
-			break;
-		return NULL;
+	/*
+	 * Local Root Port/End-point              Remote End-point
+	 * +-----------------------+ PCIe bus +----------------------+
+	 * |                       |    +-+   |                      |
+	 * |    DEV_TO_MEM   Rx Ch <----+ +---+ Tx Ch  DEV_TO_MEM    |
+	 * |                       |    | |   |                      |
+	 * |    MEM_TO_DEV   Tx Ch +----+ +---> Rx Ch  MEM_TO_DEV    |
+	 * |                       |    +-+   |                      |
+	 * +-----------------------+          +----------------------+
+	 *
+	 * 1. Normal logic:
+	 * If eDMA is embedded into the DW PCIe RP/EP and controlled from the
+	 * CPU/Application side, the Rx channel (EDMA_DIR_READ) will be used
+	 * for the device read operations (DEV_TO_MEM) and the Tx channel
+	 * (EDMA_DIR_WRITE) - for the write operations (MEM_TO_DEV).
+	 *
+	 * 2. Inverted logic:
+	 * If eDMA is embedded into a Remote PCIe EP and is controlled by the
+	 * MWr/MRd TLPs sent from the CPU's PCIe host controller, the Tx
+	 * channel (EDMA_DIR_WRITE) will be used for the device read operations
+	 * (DEV_TO_MEM) and the Rx channel (EDMA_DIR_READ) - for the write
+	 * operations (MEM_TO_DEV).
+	 *
+	 * It is the client driver responsibility to choose a proper channel
+	 * for the DMA transfers.
+	 */
+	if (chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL) {
+		if ((chan->dir == EDMA_DIR_READ && dir != DMA_DEV_TO_MEM) ||
+		    (chan->dir == EDMA_DIR_WRITE && dir != DMA_MEM_TO_DEV))
+			return NULL;
+	} else {
+		if ((chan->dir == EDMA_DIR_WRITE && dir != DMA_DEV_TO_MEM) ||
+		    (chan->dir == EDMA_DIR_READ && dir != DMA_MEM_TO_DEV))
+			return NULL;
 	}
 
 	if (xfer->type == EDMA_XFER_CYCLIC) {
Signature · 1 line
2.35.1
author
#14 lore raw

PATCH v9 6/9 dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics

In reply to Frank Li

From: Serge Semin <[email protected]>

In accordance with [1, 2] the DW eDMA controller has been created to be part of the DW PCIe Root Port and DW PCIe End-point controllers and to offload the transferring of large blocks of data between application and remote PCIe domains leaving the system CPU free for other tasks. In the first case (eDMA being part of DW PCIe Root Port) the eDMA controller is always accessible via the CPU DBI interface and never over the PCIe wire. The later case is more complex. Depending on the DW PCIe End-Point IP-core synthesize parameters it's possible to have the eDMA registers accessible not only from the application CPU side, but also via mapping the eDMA CSRs over a dedicated end-point BAR. So based on the specifics denoted above the eDMA driver is supposed to support two types of the DMA controller setups:
1) eDMA embedded into the DW PCIe Root Port/End-point and accessible over the local CPU from the application side.
2) eDMA embedded into the DW PCIe End-point and accessible via the PCIe wire with MWr/MRd TLPs generated by the CPU PCIe host controller. Since the CPU memory resides different sides in these cases the semantics of the MEM_TO_DEV and DEV_TO_MEM operations is flipped with respect to the Tx and Rx DMA channels. So MEM_TO_DEV/DEV_TO_MEM corresponds to the Tx/Rx channels in setup 1) and to the Rx/Tx channels in case of setup 2).

The DW eDMA driver has supported the case 2) since the initial commit e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver") in the framework of the drivers/dma/dw-edma/dw-edma-pcie.c driver. The case 1) support was added a bit later in commit bd96f1b2f43a ("dmaengine: dw-edma:
support local dma device transfer semantics"). Afterwards the driver was supposed to cover the both possible eDMA setups, but the later commit turned to be not fully correct. The problem was that the commit together with the new functionality support also changed the channel direction semantics in a way so the eDMA Read-channel (corresponding to the DMA_DEV_TO_MEM direction for the case 1.) now uses the sgl/cyclic base addresses as the Source addresses of the DMA-transfers and dma_slave_config.dst_addr as the Destination address of the DMA-transfers. Similarly the eDMA Write-channel (corresponding to the DMA_MEM_TO_DEV direction for case 1.) now utilizes dma_slave_config.src_addr as a source address of the DMA-transfers and sgl/cyclic base address as the Destination address of the DMA-transfers. This contradicts to the logic of the DMA-interface, which implies that DEV side is supposed to belong to the PCIe device memory and MEM - to the CPU/Application memory. Indeed it seems irrational to have the SG-list defined in the PCIe bus space, while expecting a contiguous buffer allocated in the CPU memory. Moreover the passed SG-list and cyclic DMA buffers are supposed to be mapped in a way so to be seen by the DW eDMA Application (CPU) interface. So in order to have the correct DW eDMA interface we need to invert the eDMA Rd/Wr-channels and DMA-slave directions semantics by selecting the src/dst addresses based on the DMA transfer direction instead of using the channel direction capability.

[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port, v.5.40a, March 2019, p.1092
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint, v.5.40a, March 2019, p.1189

Fixes bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics")
---
 drivers/dma/dw-edma/dw-edma-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/dma/dw-edma/dw-edma-core.c +1 -1
index 184622be500b7..9ac2723ed31fb 100644
@@ -443,7 +443,7 @@ dw_edma_device_transfer(struct dw_edma_transfer *xfer)
 		chunk->ll_region.sz += burst->sz;
 		desc->alloc_sz += burst->sz;
 
-		if (chan->dir == EDMA_DIR_WRITE) {
+		if (dir == DMA_DEV_TO_MEM) {
 			burst->sar = src_addr;
 			if (xfer->type == EDMA_XFER_CYCLIC) {
 				burst->dar = xfer->xfer.cyclic.paddr;
Signature · 1 line
2.35.1
author
#15 lore raw

PATCH v9 7/9 dmaengine: dw-edma: Add support for chip specific flags

In reply to Frank Li

Add a "flags" field to the "struct dw_edma_chip" so that the controller drivers can pass flags that are relevant to the platform.

DW_EDMA_CHIP_LOCAL - Used by the controller drivers accessing eDMA locally. Local eDMA access doesn't require generating MSIs to the remote.

---
Change from v7 to v9
-none
Change from v6 to v7
- dw_edma_chip_flags to u32
Change from v5 to v6
- use enum instead of define

Change from v4 to v5
- split two two patch
- rework commit message
Change from v3 to v4
none
Change from v2 to v3
- rework commit message
- Change to DW_EDMA_CHIP_32BIT_DBI
- using DW_EDMA_CHIP_LOCAL control msi
- Apply Bjorn's comments,

        if (!j) {
               control |= DW_EDMA_V0_LIE;
               if (!(chan->chip->flags & DW_EDMA_CHIP_LOCAL))
                               control |= DW_EDMA_V0_RIE;
        }

        if ((chan->chip->flags & DW_EDMA_CHIP_REG32BIT) ||
              !IS_ENABLED(CONFIG_64BIT)) {
          SET_CH_32(...);
          SET_CH_32(...);
       } else {
          SET_CH_64(...);
       }

Change from v1 to v2
- none

 drivers/dma/dw-edma/dw-edma-v0-core.c |  9 ++++++---
 include/linux/dma/edma.h              | 10 ++++++++++
 2 files changed, 16 insertions(+), 3 deletions(-)
drivers/dma/dw-edma/dw-edma-v0-core.c +6 -3
index c59e23b9f9fdb..2ab1059a3de1e 100644
@@ -301,6 +301,7 @@ u32 dw_edma_v0_core_status_abort_int(struct dw_edma *dw, enum dw_edma_dir dir)
 static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 {
 	struct dw_edma_burst *child;
+	struct dw_edma_chan *chan = chunk->chan;
 	struct dw_edma_v0_lli __iomem *lli;
 	struct dw_edma_v0_llp __iomem *llp;
 	u32 control = 0, i = 0;
@@ -314,9 +315,11 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 	j = chunk->bursts_alloc;
 	list_for_each_entry(child, &chunk->burst->list, list) {
 		j--;
-		if (!j)
-			control |= (DW_EDMA_V0_LIE | DW_EDMA_V0_RIE);
-
+		if (!j) {
+			control |= DW_EDMA_V0_LIE;
+			if (!(chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL))
+				control |= DW_EDMA_V0_RIE;
+		}
 		/* Channel control */
 		SET_LL_32(&lli[i].control, control);
 		/* Transfer size */
include/linux/dma/edma.h +10 -0
index c2039246fc08c..fbd05a7284934 100644
@@ -33,12 +33,21 @@ enum dw_edma_map_format {
 	EDMA_MF_HDMA_COMPAT = 0x5
 };
 
+/**
+ * enum dw_edma_chip_flags - Flags specific to an eDMA chip
+ * @DW_EDMA_CHIP_LOCAL:		eDMA is used locally by an endpoint
+ */
+enum dw_edma_chip_flags {
+	DW_EDMA_CHIP_LOCAL	= BIT(0),
+};
+
 /**
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @flags		 dw_edma_chip_flags
  * @reg_base		 DMA register base address
  * @ll_wr_cnt		 DMA write link list number
  * @ll_rd_cnt		 DMA read link list number
@@ -53,6 +62,7 @@ struct dw_edma_chip {
 	int			id;
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
+	u32			flags;
 
 	void __iomem		*reg_base;
 
Signature · 1 line
2.35.1
Reviewed-by on v9 7/9
#16 lore raw

Re: [PATCH v9 7/9] dmaengine: dw-edma: Add support for chip specific flags

Quoted 8 lines · Frank Li

Add a "flags" field to the "struct dw_edma_chip" so that the controller drivers can pass flags that are relevant to the platform.

DW_EDMA_CHIP_LOCAL - Used by the controller drivers accessing eDMA locally. Local eDMA access doesn't require generating MSIs to the remote.

Thanks,
Mani

Quoted 104 lines

---
Change from v7 to v9
-none
Change from v6 to v7
- dw_edma_chip_flags to u32
Change from v5 to v6
- use enum instead of define

Change from v4 to v5
- split two two patch
- rework commit message
Change from v3 to v4
none
Change from v2 to v3
- rework commit message
- Change to DW_EDMA_CHIP_32BIT_DBI
- using DW_EDMA_CHIP_LOCAL control msi
- Apply Bjorn's comments,

        if (!j) {
               control |= DW_EDMA_V0_LIE;
               if (!(chan->chip->flags & DW_EDMA_CHIP_LOCAL))
                               control |= DW_EDMA_V0_RIE;
        }

        if ((chan->chip->flags & DW_EDMA_CHIP_REG32BIT) ||
              !IS_ENABLED(CONFIG_64BIT)) {
          SET_CH_32(...);
          SET_CH_32(...);
       } else {
          SET_CH_64(...);
       }

Change from v1 to v2
- none

 drivers/dma/dw-edma/dw-edma-v0-core.c |  9 ++++++---
 include/linux/dma/edma.h              | 10 ++++++++++
 2 files changed, 16 insertions(+), 3 deletions(-)
drivers/dma/dw-edma/dw-edma-v0-core.c +6 -3
index c59e23b9f9fdb..2ab1059a3de1e 100644
@@ -301,6 +301,7 @@ u32 dw_edma_v0_core_status_abort_int(struct dw_edma *dw, enum dw_edma_dir dir)
 static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 {
 	struct dw_edma_burst *child;
+	struct dw_edma_chan *chan = chunk->chan;
 	struct dw_edma_v0_lli __iomem *lli;
 	struct dw_edma_v0_llp __iomem *llp;
 	u32 control = 0, i = 0;
@@ -314,9 +315,11 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 	j = chunk->bursts_alloc;
 	list_for_each_entry(child, &chunk->burst->list, list) {
 		j--;
-		if (!j)
-			control |= (DW_EDMA_V0_LIE | DW_EDMA_V0_RIE);
-
+		if (!j) {
+			control |= DW_EDMA_V0_LIE;
+			if (!(chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL))
+				control |= DW_EDMA_V0_RIE;
+		}
 		/* Channel control */
 		SET_LL_32(&lli[i].control, control);
 		/* Transfer size */
include/linux/dma/edma.h +10 -0
index c2039246fc08c..fbd05a7284934 100644
@@ -33,12 +33,21 @@ enum dw_edma_map_format {
 	EDMA_MF_HDMA_COMPAT = 0x5
 };
 
+/**
+ * enum dw_edma_chip_flags - Flags specific to an eDMA chip
+ * @DW_EDMA_CHIP_LOCAL:		eDMA is used locally by an endpoint
+ */
+enum dw_edma_chip_flags {
+	DW_EDMA_CHIP_LOCAL	= BIT(0),
+};
+
 /**
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @flags		 dw_edma_chip_flags
  * @reg_base		 DMA register base address
  * @ll_wr_cnt		 DMA write link list number
  * @ll_rd_cnt		 DMA read link list number
@@ -53,6 +62,7 @@ struct dw_edma_chip {
 	int			id;
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
+	u32			flags;
 
 	void __iomem		*reg_base;
 
Signature · 1 line
2.35.1
author
#17 lore raw

PATCH v9 8/9 dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags

In reply to Frank Li

DW_EDMA_CHIP_32BIT_DBI was used by the controller drivers like i.MX8 that allows only 32bit access to the DBI region.

---

Change from v6 to v9
- none
Change from v5 to v6
- use enum instead of define
New patch at v5
- fix kernel test robot build error

 drivers/dma/dw-edma/dw-edma-v0-core.c | 13 ++++++++-----
 include/linux/dma/edma.h              |  2 ++
 2 files changed, 10 insertions(+), 5 deletions(-)
drivers/dma/dw-edma/dw-edma-v0-core.c +8 -5
index 2ab1059a3de1e..2d3f74ccc340a 100644
@@ -417,15 +417,18 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 		SET_CH_32(dw, chan->dir, chan->id, ch_control1,
 			  (DW_EDMA_V0_CCS | DW_EDMA_V0_LLE));
 		/* Linked list */
-		#ifdef CONFIG_64BIT
-			SET_CH_64(dw, chan->dir, chan->id, llp.reg,
-				  chunk->ll_region.paddr);
-		#else /* CONFIG_64BIT */
+		if ((chan->dw->chip->flags & DW_EDMA_CHIP_32BIT_DBI) ||
+		    !IS_ENABLED(CONFIG_64BIT)) {
 			SET_CH_32(dw, chan->dir, chan->id, llp.lsb,
 				  lower_32_bits(chunk->ll_region.paddr));
 			SET_CH_32(dw, chan->dir, chan->id, llp.msb,
 				  upper_32_bits(chunk->ll_region.paddr));
-		#endif /* CONFIG_64BIT */
+		} else {
+		#ifdef CONFIG_64BIT
+			SET_CH_64(dw, chan->dir, chan->id, llp.reg,
+				  chunk->ll_region.paddr);
+		#endif
+		}
 	}
 	/* Doorbell */
 	SET_RW_32(dw, chan->dir, doorbell,
include/linux/dma/edma.h +2 -0
index fbd05a7284934..8b134896c9edb 100644
@@ -36,9 +36,11 @@ enum dw_edma_map_format {
 /**
  * enum dw_edma_chip_flags - Flags specific to an eDMA chip
  * @DW_EDMA_CHIP_LOCAL:		eDMA is used locally by an endpoint
+ * @DW_EDMA_CHIP_32BIT_DBI	Only support 32bit DBI register access
  */
 enum dw_edma_chip_flags {
 	DW_EDMA_CHIP_LOCAL	= BIT(0),
+	DW_EDMA_CHIP_32BIT_DBI	= BIT(1),
 };
 
 /**
Signature · 1 line
2.35.1
Reviewed-by on v9 8/9
#18 lore raw

Re: [PATCH v9 8/9] dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags

Quoted 5 lines · Frank Li

DW_EDMA_CHIP_32BIT_DBI was used by the controller drivers like i.MX8 that allows only 32bit access to the DBI region.

Thanks,
Mani

Quoted 60 lines

---

Change from v6 to v9
- none
Change from v5 to v6
- use enum instead of define
New patch at v5
- fix kernel test robot build error

 drivers/dma/dw-edma/dw-edma-v0-core.c | 13 ++++++++-----
 include/linux/dma/edma.h              |  2 ++
 2 files changed, 10 insertions(+), 5 deletions(-)
drivers/dma/dw-edma/dw-edma-v0-core.c +8 -5
index 2ab1059a3de1e..2d3f74ccc340a 100644
@@ -417,15 +417,18 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 		SET_CH_32(dw, chan->dir, chan->id, ch_control1,
 			  (DW_EDMA_V0_CCS | DW_EDMA_V0_LLE));
 		/* Linked list */
-		#ifdef CONFIG_64BIT
-			SET_CH_64(dw, chan->dir, chan->id, llp.reg,
-				  chunk->ll_region.paddr);
-		#else /* CONFIG_64BIT */
+		if ((chan->dw->chip->flags & DW_EDMA_CHIP_32BIT_DBI) ||
+		    !IS_ENABLED(CONFIG_64BIT)) {
 			SET_CH_32(dw, chan->dir, chan->id, llp.lsb,
 				  lower_32_bits(chunk->ll_region.paddr));
 			SET_CH_32(dw, chan->dir, chan->id, llp.msb,
 				  upper_32_bits(chunk->ll_region.paddr));
-		#endif /* CONFIG_64BIT */
+		} else {
+		#ifdef CONFIG_64BIT
+			SET_CH_64(dw, chan->dir, chan->id, llp.reg,
+				  chunk->ll_region.paddr);
+		#endif
+		}
 	}
 	/* Doorbell */
 	SET_RW_32(dw, chan->dir, doorbell,
include/linux/dma/edma.h +2 -0
index fbd05a7284934..8b134896c9edb 100644
@@ -36,9 +36,11 @@ enum dw_edma_map_format {
 /**
  * enum dw_edma_chip_flags - Flags specific to an eDMA chip
  * @DW_EDMA_CHIP_LOCAL:		eDMA is used locally by an endpoint
+ * @DW_EDMA_CHIP_32BIT_DBI	Only support 32bit DBI register access
  */
 enum dw_edma_chip_flags {
 	DW_EDMA_CHIP_LOCAL	= BIT(0),
+	DW_EDMA_CHIP_32BIT_DBI	= BIT(1),
 };
 
 /**
Signature · 1 line
2.35.1
author
#19 lore raw

PATCH v9 9/9 PCI: endpoint: Add embedded DMA controller test

In reply to Frank Li

Designware provided eDMA support in controller. This enabled use this eDMA controller to transfer data.

The whole flow align with standard DMA usage module

1. Using dma_request_channel() and filter function to find correct RX and TX Channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();

Tested at i.MX8DXL platform.

root@imx8qmmek:~# /usr/bin/pcitest -d -w
WRITE ( 102400 bytes):          OKAY
root@imx8qmmek:~# /usr/bin/pcitest -d -r
READ ( 102400 bytes):           OKAY

WRITE => Size: 102400 bytes DMA: YES Time: 0.000180145 seconds Rate: 555108 KB/s READ => Size: 102400 bytes DMA: YES Time: 0.000194397 seconds Rate: 514411 KB/s

READ => Size: 102400 bytes DMA: NO Time: 0.013532597 seconds Rate: 7389 KB/s
WRITE => Size: 102400 bytes DMA: NO Time: 0.000857090 seconds Rate: 116673 KB/s

---
Change from v6 to v9:
- none
Change from v5 to v6:
- change subject
Change from v4 to v5:
- none
Change from v3 to v4:
- reverse Xmas tree order
- local -> dma_local
- change error message
- IS_ERR -> IS_ERR_OR_NULL
- check return value of dmaengine_slave_config()
Change from v1 to v2:
- none

 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++++++--
 1 file changed, 98 insertions(+), 10 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +98 -10
index 90d84d3bc868f..f26afd02f3a86 100644
@@ -52,9 +52,11 @@ struct pci_epf_test {
 	enum pci_barno		test_reg_bar;
 	size_t			msix_table_offset;
 	struct delayed_work	cmd_handler;
-	struct dma_chan		*dma_chan;
+	struct dma_chan		*dma_chan_tx;
+	struct dma_chan		*dma_chan_rx;
 	struct completion	transfer_complete;
 	bool			dma_supported;
+	bool			dma_private;
 	const struct pci_epc_features *epc_features;
 };
 
@@ -105,12 +107,15 @@ static void pci_epf_test_dma_callback(void *param)
  */
 static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 				      dma_addr_t dma_dst, dma_addr_t dma_src,
-				      size_t len)
+				      size_t len, dma_addr_t dma_remote,
+				      enum dma_transfer_direction dir)
 {
+	struct dma_chan *chan = (dir == DMA_DEV_TO_MEM) ? epf_test->dma_chan_tx : epf_test->dma_chan_rx;
+	dma_addr_t dma_local = (dir == DMA_MEM_TO_DEV) ? dma_src : dma_dst;
 	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
-	struct dma_chan *chan = epf_test->dma_chan;
 	struct pci_epf *epf = epf_test->epf;
 	struct dma_async_tx_descriptor *tx;
+	struct dma_slave_config sconf = {};
 	struct device *dev = &epf->dev;
 	dma_cookie_t cookie;
 	int ret;
@@ -120,7 +125,22 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 		return -EINVAL;
 	}
 
-	tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	if (epf_test->dma_private) {
+		sconf.direction = dir;
+		if (dir == DMA_MEM_TO_DEV)
+			sconf.dst_addr = dma_remote;
+		else
+			sconf.src_addr = dma_remote;
+
+		if (dmaengine_slave_config(chan, &sconf)) {
+			dev_err(dev, "DMA slave config fail\n");
+			return -EIO;
+		}
+		tx = dmaengine_prep_slave_single(chan, dma_local, len, dir, flags);
+	} else {
+		tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	}
+
 	if (!tx) {
 		dev_err(dev, "Failed to prepare DMA memcpy\n");
 		return -EIO;
@@ -148,6 +168,23 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 	return 0;
 }
 
+struct epf_dma_filter {
+	struct device *dev;
+	u32 dma_mask;
+};
+
+static bool epf_dma_filter_fn(struct dma_chan *chan, void *node)
+{
+	struct epf_dma_filter *filter = node;
+	struct dma_slave_caps caps;
+
+	memset(&caps, 0, sizeof(caps));
+	dma_get_slave_caps(chan, &caps);
+
+	return chan->device->dev == filter->dev
+		&& (filter->dma_mask & caps.directions);
+}
+
 /**
  * pci_epf_test_init_dma_chan() - Function to initialize EPF test DMA channel
  * @epf_test: the EPF test device that performs data transfer operation
@@ -158,10 +195,44 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 {
 	struct pci_epf *epf = epf_test->epf;
 	struct device *dev = &epf->dev;
+	struct epf_dma_filter filter;
 	struct dma_chan *dma_chan;
 	dma_cap_mask_t mask;
 	int ret;
 
+	filter.dev = epf->epc->dev.parent;
+	filter.dma_mask = BIT(DMA_DEV_TO_MEM);
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+	if (IS_ERR_OR_NULL(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+		goto fail_back_tx;
+	}
+
+	epf_test->dma_chan_rx = dma_chan;
+
+	filter.dma_mask = BIT(DMA_MEM_TO_DEV);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+
+	if (IS_ERR(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+		goto fail_back_rx;
+	}
+
+	epf_test->dma_chan_tx = dma_chan;
+	epf_test->dma_private = true;
+
+	init_completion(&epf_test->transfer_complete);
+
+	return 0;
+
+fail_back_rx:
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_tx = NULL;
+
+fail_back_tx:
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_MEMCPY, mask);
 
@@ -174,7 +245,7 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 	}
 	init_completion(&epf_test->transfer_complete);
 
-	epf_test->dma_chan = dma_chan;
+	epf_test->dma_chan_tx = epf_test->dma_chan_rx = dma_chan;
 
 	return 0;
 }
@@ -190,8 +261,17 @@ static void pci_epf_test_clean_dma_chan(struct pci_epf_test *epf_test)
 	if (!epf_test->dma_supported)
 		return;
 
-	dma_release_channel(epf_test->dma_chan);
-	epf_test->dma_chan = NULL;
+	dma_release_channel(epf_test->dma_chan_tx);
+	if (epf_test->dma_chan_tx == epf_test->dma_chan_rx) {
+		epf_test->dma_chan_tx = NULL;
+		epf_test->dma_chan_rx = NULL;
+		return;
+	}
+
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_rx = NULL;
+
+	return;
 }
 
 static void pci_epf_test_print_rate(const char *ops, u64 size,
@@ -280,8 +360,14 @@ static int pci_epf_test_copy(struct pci_epf_test *epf_test)
 			goto err_map_addr;
 		}
 
+		if (epf_test->dma_private) {
+			dev_err(dev, "Cannot transfer data using DMA\n");
+			ret = -EINVAL;
+			goto err_map_addr;
+		}
+
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, 0, DMA_MEM_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 	} else {
@@ -363,7 +449,8 @@ static int pci_epf_test_read(struct pci_epf_test *epf_test)
 
 		ktime_get_ts64(&start);
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 phys_addr, reg->size);
+						 phys_addr, reg->size,
+						 reg->src_addr, DMA_DEV_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
@@ -453,8 +540,9 @@ static int pci_epf_test_write(struct pci_epf_test *epf_test)
 		}
 
 		ktime_get_ts64(&start);
+
 		ret = pci_epf_test_data_transfer(epf_test, phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, reg->dst_addr, DMA_MEM_TO_DEV);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
Signature · 1 line
2.35.1
Acked-by on v9 9/9
#20 lore raw

Re: [PATCH v9 9/9] PCI: endpoint: Add embedded DMA controller test

Quoted 19 lines · Frank Li

Designware provided eDMA support in controller. This enabled use this eDMA controller to transfer data.

The whole flow align with standard DMA usage module

1. Using dma_request_channel() and filter function to find correct RX and TX Channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();

Tested at i.MX8DXL platform.

root@imx8qmmek:~# /usr/bin/pcitest -d -w
WRITE ( 102400 bytes):          OKAY
root@imx8qmmek:~# /usr/bin/pcitest -d -r
READ ( 102400 bytes):           OKAY
Quoted 7 lines

WRITE => Size: 102400 bytes DMA: YES Time: 0.000180145 seconds Rate: 555108 KB/s READ => Size: 102400 bytes DMA: YES Time: 0.000194397 seconds Rate: 514411 KB/s

READ => Size: 102400 bytes DMA: NO Time: 0.013532597 seconds Rate: 7389 KB/s
WRITE => Size: 102400 bytes DMA: NO Time: 0.000857090 seconds Rate: 116673 KB/s

Patch looks good to me but I cannot test it on my platform. So,

Thanks,
Mani

Quoted 216 lines

---
Change from v6 to v9:
- none
Change from v5 to v6:
- change subject
Change from v4 to v5:
- none
Change from v3 to v4:
- reverse Xmas tree order
- local -> dma_local
- change error message
- IS_ERR -> IS_ERR_OR_NULL
- check return value of dmaengine_slave_config()
Change from v1 to v2:
- none

 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++++++--
 1 file changed, 98 insertions(+), 10 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +98 -10
index 90d84d3bc868f..f26afd02f3a86 100644
@@ -52,9 +52,11 @@ struct pci_epf_test {
 	enum pci_barno		test_reg_bar;
 	size_t			msix_table_offset;
 	struct delayed_work	cmd_handler;
-	struct dma_chan		*dma_chan;
+	struct dma_chan		*dma_chan_tx;
+	struct dma_chan		*dma_chan_rx;
 	struct completion	transfer_complete;
 	bool			dma_supported;
+	bool			dma_private;
 	const struct pci_epc_features *epc_features;
 };
 
@@ -105,12 +107,15 @@ static void pci_epf_test_dma_callback(void *param)
  */
 static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 				      dma_addr_t dma_dst, dma_addr_t dma_src,
-				      size_t len)
+				      size_t len, dma_addr_t dma_remote,
+				      enum dma_transfer_direction dir)
 {
+	struct dma_chan *chan = (dir == DMA_DEV_TO_MEM) ? epf_test->dma_chan_tx : epf_test->dma_chan_rx;
+	dma_addr_t dma_local = (dir == DMA_MEM_TO_DEV) ? dma_src : dma_dst;
 	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
-	struct dma_chan *chan = epf_test->dma_chan;
 	struct pci_epf *epf = epf_test->epf;
 	struct dma_async_tx_descriptor *tx;
+	struct dma_slave_config sconf = {};
 	struct device *dev = &epf->dev;
 	dma_cookie_t cookie;
 	int ret;
@@ -120,7 +125,22 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 		return -EINVAL;
 	}
 
-	tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	if (epf_test->dma_private) {
+		sconf.direction = dir;
+		if (dir == DMA_MEM_TO_DEV)
+			sconf.dst_addr = dma_remote;
+		else
+			sconf.src_addr = dma_remote;
+
+		if (dmaengine_slave_config(chan, &sconf)) {
+			dev_err(dev, "DMA slave config fail\n");
+			return -EIO;
+		}
+		tx = dmaengine_prep_slave_single(chan, dma_local, len, dir, flags);
+	} else {
+		tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	}
+
 	if (!tx) {
 		dev_err(dev, "Failed to prepare DMA memcpy\n");
 		return -EIO;
@@ -148,6 +168,23 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 	return 0;
 }
 
+struct epf_dma_filter {
+	struct device *dev;
+	u32 dma_mask;
+};
+
+static bool epf_dma_filter_fn(struct dma_chan *chan, void *node)
+{
+	struct epf_dma_filter *filter = node;
+	struct dma_slave_caps caps;
+
+	memset(&caps, 0, sizeof(caps));
+	dma_get_slave_caps(chan, &caps);
+
+	return chan->device->dev == filter->dev
+		&& (filter->dma_mask & caps.directions);
+}
+
 /**
  * pci_epf_test_init_dma_chan() - Function to initialize EPF test DMA channel
  * @epf_test: the EPF test device that performs data transfer operation
@@ -158,10 +195,44 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 {
 	struct pci_epf *epf = epf_test->epf;
 	struct device *dev = &epf->dev;
+	struct epf_dma_filter filter;
 	struct dma_chan *dma_chan;
 	dma_cap_mask_t mask;
 	int ret;
 
+	filter.dev = epf->epc->dev.parent;
+	filter.dma_mask = BIT(DMA_DEV_TO_MEM);
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+	if (IS_ERR_OR_NULL(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+		goto fail_back_tx;
+	}
+
+	epf_test->dma_chan_rx = dma_chan;
+
+	filter.dma_mask = BIT(DMA_MEM_TO_DEV);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+
+	if (IS_ERR(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+		goto fail_back_rx;
+	}
+
+	epf_test->dma_chan_tx = dma_chan;
+	epf_test->dma_private = true;
+
+	init_completion(&epf_test->transfer_complete);
+
+	return 0;
+
+fail_back_rx:
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_tx = NULL;
+
+fail_back_tx:
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_MEMCPY, mask);
 
@@ -174,7 +245,7 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 	}
 	init_completion(&epf_test->transfer_complete);
 
-	epf_test->dma_chan = dma_chan;
+	epf_test->dma_chan_tx = epf_test->dma_chan_rx = dma_chan;
 
 	return 0;
 }
@@ -190,8 +261,17 @@ static void pci_epf_test_clean_dma_chan(struct pci_epf_test *epf_test)
 	if (!epf_test->dma_supported)
 		return;
 
-	dma_release_channel(epf_test->dma_chan);
-	epf_test->dma_chan = NULL;
+	dma_release_channel(epf_test->dma_chan_tx);
+	if (epf_test->dma_chan_tx == epf_test->dma_chan_rx) {
+		epf_test->dma_chan_tx = NULL;
+		epf_test->dma_chan_rx = NULL;
+		return;
+	}
+
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_rx = NULL;
+
+	return;
 }
 
 static void pci_epf_test_print_rate(const char *ops, u64 size,
@@ -280,8 +360,14 @@ static int pci_epf_test_copy(struct pci_epf_test *epf_test)
 			goto err_map_addr;
 		}
 
+		if (epf_test->dma_private) {
+			dev_err(dev, "Cannot transfer data using DMA\n");
+			ret = -EINVAL;
+			goto err_map_addr;
+		}
+
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, 0, DMA_MEM_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 	} else {
@@ -363,7 +449,8 @@ static int pci_epf_test_read(struct pci_epf_test *epf_test)
 
 		ktime_get_ts64(&start);
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 phys_addr, reg->size);
+						 phys_addr, reg->size,
+						 reg->src_addr, DMA_DEV_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
@@ -453,8 +540,9 @@ static int pci_epf_test_write(struct pci_epf_test *epf_test)
 		}
 
 		ktime_get_ts64(&start);
+
 		ret = pci_epf_test_data_transfer(epf_test, phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, reg->dst_addr, DMA_MEM_TO_DEV);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
Signature · 1 line
2.35.1
#21 lore raw

Re: [PATCH v9 9/9] PCI: endpoint: Add embedded DMA controller test

In reply to Frank Li
Quoted 19 lines · Frank Li

Designware provided eDMA support in controller. This enabled use this eDMA controller to transfer data.

The whole flow align with standard DMA usage module

1. Using dma_request_channel() and filter function to find correct RX and TX Channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();

Tested at i.MX8DXL platform.

root@imx8qmmek:~# /usr/bin/pcitest -d -w
WRITE ( 102400 bytes):          OKAY
root@imx8qmmek:~# /usr/bin/pcitest -d -r
READ ( 102400 bytes):           OKAY
Quoted 6 lines

WRITE => Size: 102400 bytes DMA: YES Time: 0.000180145 seconds Rate: 555108 KB/s READ => Size: 102400 bytes DMA: YES Time: 0.000194397 seconds Rate: 514411 KB/s

READ => Size: 102400 bytes DMA: NO Time: 0.013532597 seconds Rate: 7389 KB/s
WRITE => Size: 102400 bytes DMA: NO Time: 0.000857090 seconds Rate: 116673 KB/s

You should rewrite this commit log.

1) this is not Designware specific
2) On what platforms you tested is information for a cover letter but not very useful for a commit log
3) The commit log describes why you need the patch and what the patch does.
It can be a one liner: "Enable DMA controller tests for endpoints with DMA capabilities". Or something along those lines.

Lorenzo

Quoted 217 lines

---
Change from v6 to v9:
- none
Change from v5 to v6:
- change subject
Change from v4 to v5:
- none
Change from v3 to v4:
- reverse Xmas tree order
- local -> dma_local
- change error message
- IS_ERR -> IS_ERR_OR_NULL
- check return value of dmaengine_slave_config()
Change from v1 to v2:
- none

 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++++++--
 1 file changed, 98 insertions(+), 10 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +98 -10
index 90d84d3bc868f..f26afd02f3a86 100644
@@ -52,9 +52,11 @@ struct pci_epf_test {
 	enum pci_barno		test_reg_bar;
 	size_t			msix_table_offset;
 	struct delayed_work	cmd_handler;
-	struct dma_chan		*dma_chan;
+	struct dma_chan		*dma_chan_tx;
+	struct dma_chan		*dma_chan_rx;
 	struct completion	transfer_complete;
 	bool			dma_supported;
+	bool			dma_private;
 	const struct pci_epc_features *epc_features;
 };
 
@@ -105,12 +107,15 @@ static void pci_epf_test_dma_callback(void *param)
  */
 static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 				      dma_addr_t dma_dst, dma_addr_t dma_src,
-				      size_t len)
+				      size_t len, dma_addr_t dma_remote,
+				      enum dma_transfer_direction dir)
 {
+	struct dma_chan *chan = (dir == DMA_DEV_TO_MEM) ? epf_test->dma_chan_tx : epf_test->dma_chan_rx;
+	dma_addr_t dma_local = (dir == DMA_MEM_TO_DEV) ? dma_src : dma_dst;
 	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
-	struct dma_chan *chan = epf_test->dma_chan;
 	struct pci_epf *epf = epf_test->epf;
 	struct dma_async_tx_descriptor *tx;
+	struct dma_slave_config sconf = {};
 	struct device *dev = &epf->dev;
 	dma_cookie_t cookie;
 	int ret;
@@ -120,7 +125,22 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 		return -EINVAL;
 	}
 
-	tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	if (epf_test->dma_private) {
+		sconf.direction = dir;
+		if (dir == DMA_MEM_TO_DEV)
+			sconf.dst_addr = dma_remote;
+		else
+			sconf.src_addr = dma_remote;
+
+		if (dmaengine_slave_config(chan, &sconf)) {
+			dev_err(dev, "DMA slave config fail\n");
+			return -EIO;
+		}
+		tx = dmaengine_prep_slave_single(chan, dma_local, len, dir, flags);
+	} else {
+		tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	}
+
 	if (!tx) {
 		dev_err(dev, "Failed to prepare DMA memcpy\n");
 		return -EIO;
@@ -148,6 +168,23 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 	return 0;
 }
 
+struct epf_dma_filter {
+	struct device *dev;
+	u32 dma_mask;
+};
+
+static bool epf_dma_filter_fn(struct dma_chan *chan, void *node)
+{
+	struct epf_dma_filter *filter = node;
+	struct dma_slave_caps caps;
+
+	memset(&caps, 0, sizeof(caps));
+	dma_get_slave_caps(chan, &caps);
+
+	return chan->device->dev == filter->dev
+		&& (filter->dma_mask & caps.directions);
+}
+
 /**
  * pci_epf_test_init_dma_chan() - Function to initialize EPF test DMA channel
  * @epf_test: the EPF test device that performs data transfer operation
@@ -158,10 +195,44 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 {
 	struct pci_epf *epf = epf_test->epf;
 	struct device *dev = &epf->dev;
+	struct epf_dma_filter filter;
 	struct dma_chan *dma_chan;
 	dma_cap_mask_t mask;
 	int ret;
 
+	filter.dev = epf->epc->dev.parent;
+	filter.dma_mask = BIT(DMA_DEV_TO_MEM);
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+	if (IS_ERR_OR_NULL(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+		goto fail_back_tx;
+	}
+
+	epf_test->dma_chan_rx = dma_chan;
+
+	filter.dma_mask = BIT(DMA_MEM_TO_DEV);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+
+	if (IS_ERR(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+		goto fail_back_rx;
+	}
+
+	epf_test->dma_chan_tx = dma_chan;
+	epf_test->dma_private = true;
+
+	init_completion(&epf_test->transfer_complete);
+
+	return 0;
+
+fail_back_rx:
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_tx = NULL;
+
+fail_back_tx:
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_MEMCPY, mask);
 
@@ -174,7 +245,7 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 	}
 	init_completion(&epf_test->transfer_complete);
 
-	epf_test->dma_chan = dma_chan;
+	epf_test->dma_chan_tx = epf_test->dma_chan_rx = dma_chan;
 
 	return 0;
 }
@@ -190,8 +261,17 @@ static void pci_epf_test_clean_dma_chan(struct pci_epf_test *epf_test)
 	if (!epf_test->dma_supported)
 		return;
 
-	dma_release_channel(epf_test->dma_chan);
-	epf_test->dma_chan = NULL;
+	dma_release_channel(epf_test->dma_chan_tx);
+	if (epf_test->dma_chan_tx == epf_test->dma_chan_rx) {
+		epf_test->dma_chan_tx = NULL;
+		epf_test->dma_chan_rx = NULL;
+		return;
+	}
+
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_rx = NULL;
+
+	return;
 }
 
 static void pci_epf_test_print_rate(const char *ops, u64 size,
@@ -280,8 +360,14 @@ static int pci_epf_test_copy(struct pci_epf_test *epf_test)
 			goto err_map_addr;
 		}
 
+		if (epf_test->dma_private) {
+			dev_err(dev, "Cannot transfer data using DMA\n");
+			ret = -EINVAL;
+			goto err_map_addr;
+		}
+
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, 0, DMA_MEM_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 	} else {
@@ -363,7 +449,8 @@ static int pci_epf_test_read(struct pci_epf_test *epf_test)
 
 		ktime_get_ts64(&start);
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 phys_addr, reg->size);
+						 phys_addr, reg->size,
+						 reg->src_addr, DMA_DEV_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
@@ -453,8 +540,9 @@ static int pci_epf_test_write(struct pci_epf_test *epf_test)
 		}
 
 		ktime_get_ts64(&start);
+
 		ret = pci_epf_test_data_transfer(epf_test, phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, reg->dst_addr, DMA_MEM_TO_DEV);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
Signature · 1 line
2.35.1
#22 lore raw

Re: [PATCH v9 9/9] PCI: endpoint: Add embedded DMA controller test

Quoted 30 lines · Lorenzo Pieralisi
Quoted 19 lines · Frank Li

Designware provided eDMA support in controller. This enabled use this eDMA controller to transfer data.

The whole flow align with standard DMA usage module

1. Using dma_request_channel() and filter function to find correct RX and TX Channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();

Tested at i.MX8DXL platform.

root@imx8qmmek:~# /usr/bin/pcitest -d -w
WRITE ( 102400 bytes):          OKAY
root@imx8qmmek:~# /usr/bin/pcitest -d -r
READ ( 102400 bytes):           OKAY
Quoted 6 lines

WRITE => Size: 102400 bytes DMA: YES Time: 0.000180145 seconds Rate: 555108 KB/s READ => Size: 102400 bytes DMA: YES Time: 0.000194397 seconds Rate: 514411 KB/s

READ => Size: 102400 bytes DMA: NO Time: 0.013532597 seconds Rate: 7389 KB/s
WRITE => Size: 102400 bytes DMA: NO Time: 0.000857090 seconds Rate: 116673 KB/s

You should rewrite this commit log.

Quoted 7 lines

1) this is not Designware specific
2) On what platforms you tested is information for a cover letter but not very useful for a commit log
3) The commit log describes why you need the patch and what the patch does.
It can be a one liner: "Enable DMA controller tests for endpoints with DMA capabilities". Or something along those lines.

How about write as below

PCI: endpoint: Enable DMA controller tests for endpoints with DMA capabilities

Some Endpoints controllers have DMA capabilities. This DMA controller has more efficiency then a general external DMA controller. And this DMA controller can bypass
outbound memory address translation unit.

The whole flow use standard DMA usage module

1. Using dma_request_channel() and filter function to find correct RX and TX Channel. if not exist, failure back to try allocate
general DMA controller
channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();
.
best regards
Frank Li

Quoted 220 lines

Lorenzo

Quoted 217 lines

---
Change from v6 to v9:
- none
Change from v5 to v6:
- change subject
Change from v4 to v5:
- none
Change from v3 to v4:
- reverse Xmas tree order
- local -> dma_local
- change error message
- IS_ERR -> IS_ERR_OR_NULL
- check return value of dmaengine_slave_config()
Change from v1 to v2:
- none

 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++++++--
 1 file changed, 98 insertions(+), 10 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +98 -11
index 90d84d3bc868f..f26afd02f3a86 100644
@@ -52,9 +52,11 @@ struct pci_epf_test {
      enum pci_barno          test_reg_bar;
      size_t                  msix_table_offset;
      struct delayed_work     cmd_handler;
-     struct dma_chan         *dma_chan;
+     struct dma_chan         *dma_chan_tx;
+     struct dma_chan         *dma_chan_rx;
      struct completion       transfer_complete;
      bool                    dma_supported;
+     bool                    dma_private;
      const struct pci_epc_features *epc_features;
 };
 
@@ -105,12 +107,15 @@ static void pci_epf_test_dma_callback(void *param)
  */
 static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
                                    dma_addr_t dma_dst, dma_addr_t dma_src,
-                                   size_t len)
+                                   size_t len, dma_addr_t dma_remote,
+                                   enum dma_transfer_direction dir)
 {
+     struct dma_chan *chan = (dir == DMA_DEV_TO_MEM) ? epf_test->dma_chan_tx : epf_test->dma_chan_rx;
+     dma_addr_t dma_local = (dir == DMA_MEM_TO_DEV) ? dma_src : dma_dst;
      enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
-     struct dma_chan *chan = epf_test->dma_chan;
      struct pci_epf *epf = epf_test->epf;
      struct dma_async_tx_descriptor *tx;
+     struct dma_slave_config sconf = {};
      struct device *dev = &epf->dev;
      dma_cookie_t cookie;
      int ret;
@@ -120,7 +125,22 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
              return -EINVAL;
      }
 
-     tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+     if (epf_test->dma_private) {
+             sconf.direction = dir;
+             if (dir == DMA_MEM_TO_DEV)
+                     sconf.dst_addr = dma_remote;
+             else
+                     sconf.src_addr = dma_remote;
+
+             if (dmaengine_slave_config(chan, &sconf)) {
+                     dev_err(dev, "DMA slave config fail\n");
+                     return -EIO;
+             }
+             tx = dmaengine_prep_slave_single(chan, dma_local, len, dir, flags);
+     } else {
+             tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+     }
+
      if (!tx) {
              dev_err(dev, "Failed to prepare DMA memcpy\n");
              return -EIO;
@@ -148,6 +168,23 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
      return 0;
 }
 
+struct epf_dma_filter {
+     struct device *dev;
+     u32 dma_mask;
+};
+
+static bool epf_dma_filter_fn(struct dma_chan *chan, void *node)
+{
+     struct epf_dma_filter *filter = node;
+     struct dma_slave_caps caps;
+
+     memset(&caps, 0, sizeof(caps));
+     dma_get_slave_caps(chan, &caps);
+
+     return chan->device->dev == filter->dev
+             && (filter->dma_mask & caps.directions);
+}
+
 /**
  * pci_epf_test_init_dma_chan() - Function to initialize EPF test DMA channel
  * @epf_test: the EPF test device that performs data transfer operation
@@ -158,10 +195,44 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 {
      struct pci_epf *epf = epf_test->epf;
      struct device *dev = &epf->dev;
+     struct epf_dma_filter filter;
      struct dma_chan *dma_chan;
      dma_cap_mask_t mask;
      int ret;
 
+     filter.dev = epf->epc->dev.parent;
+     filter.dma_mask = BIT(DMA_DEV_TO_MEM);
+
+     dma_cap_zero(mask);
+     dma_cap_set(DMA_SLAVE, mask);
+     dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+     if (IS_ERR_OR_NULL(dma_chan)) {
+             dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+             goto fail_back_tx;
+     }
+
+     epf_test->dma_chan_rx = dma_chan;
+
+     filter.dma_mask = BIT(DMA_MEM_TO_DEV);
+     dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+
+     if (IS_ERR(dma_chan)) {
+             dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+             goto fail_back_rx;
+     }
+
+     epf_test->dma_chan_tx = dma_chan;
+     epf_test->dma_private = true;
+
+     init_completion(&epf_test->transfer_complete);
+
+     return 0;
+
+fail_back_rx:
+     dma_release_channel(epf_test->dma_chan_rx);
+     epf_test->dma_chan_tx = NULL;
+
+fail_back_tx:
      dma_cap_zero(mask);
      dma_cap_set(DMA_MEMCPY, mask);
 
@@ -174,7 +245,7 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
      }
      init_completion(&epf_test->transfer_complete);
 
-     epf_test->dma_chan = dma_chan;
+     epf_test->dma_chan_tx = epf_test->dma_chan_rx = dma_chan;
 
      return 0;
 }
@@ -190,8 +261,17 @@ static void pci_epf_test_clean_dma_chan(struct pci_epf_test *epf_test)
      if (!epf_test->dma_supported)
              return;
 
-     dma_release_channel(epf_test->dma_chan);
-     epf_test->dma_chan = NULL;
+     dma_release_channel(epf_test->dma_chan_tx);
+     if (epf_test->dma_chan_tx == epf_test->dma_chan_rx) {
+             epf_test->dma_chan_tx = NULL;
+             epf_test->dma_chan_rx = NULL;
+             return;
+     }
+
+     dma_release_channel(epf_test->dma_chan_rx);
+     epf_test->dma_chan_rx = NULL;
+
+     return;
 }
 
 static void pci_epf_test_print_rate(const char *ops, u64 size,
@@ -280,8 +360,14 @@ static int pci_epf_test_copy(struct pci_epf_test *epf_test)
                      goto err_map_addr;
              }
 
+             if (epf_test->dma_private) {
+                     dev_err(dev, "Cannot transfer data using DMA\n");
+                     ret = -EINVAL;
+                     goto err_map_addr;
+             }
+
              ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-                                              src_phys_addr, reg->size);
+                                              src_phys_addr, reg->size, 0, DMA_MEM_TO_MEM);
              if (ret)
                      dev_err(dev, "Data transfer failed\n");
      } else {
@@ -363,7 +449,8 @@ static int pci_epf_test_read(struct pci_epf_test *epf_test)
 
              ktime_get_ts64(&start);
              ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-                                              phys_addr, reg->size);
+                                              phys_addr, reg->size,
+                                              reg->src_addr, DMA_DEV_TO_MEM);
              if (ret)
                      dev_err(dev, "Data transfer failed\n");
              ktime_get_ts64(&end);
@@ -453,8 +540,9 @@ static int pci_epf_test_write(struct pci_epf_test *epf_test)
              }
 
              ktime_get_ts64(&start);
+
              ret = pci_epf_test_data_transfer(epf_test, phys_addr,
-                                              src_phys_addr, reg->size);
+                                              src_phys_addr, reg->size, reg->dst_addr, DMA_MEM_TO_DEV);
              if (ret)
                      dev_err(dev, "Data transfer failed\n");
              ktime_get_ts64(&end);
--

2.35.1

#23 lore raw

Re: [PATCH v9 9/9] PCI: endpoint: Add embedded DMA controller test

Quoted 52 lines · Zhi Li
Quoted 30 lines · Lorenzo Pieralisi
Quoted 19 lines · Frank Li

Designware provided eDMA support in controller. This enabled use this eDMA controller to transfer data.

The whole flow align with standard DMA usage module

1. Using dma_request_channel() and filter function to find correct RX and TX Channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();

Tested at i.MX8DXL platform.

root@imx8qmmek:~# /usr/bin/pcitest -d -w
WRITE ( 102400 bytes):          OKAY
root@imx8qmmek:~# /usr/bin/pcitest -d -r
READ ( 102400 bytes):           OKAY
Quoted 6 lines

WRITE => Size: 102400 bytes DMA: YES Time: 0.000180145 seconds Rate: 555108 KB/s READ => Size: 102400 bytes DMA: YES Time: 0.000194397 seconds Rate: 514411 KB/s

READ => Size: 102400 bytes DMA: NO Time: 0.013532597 seconds Rate: 7389 KB/s
WRITE => Size: 102400 bytes DMA: NO Time: 0.000857090 seconds Rate: 116673 KB/s

You should rewrite this commit log.

Quoted 7 lines

1) this is not Designware specific
2) On what platforms you tested is information for a cover letter but not very useful for a commit log
3) The commit log describes why you need the patch and what the patch does.
It can be a one liner: "Enable DMA controller tests for endpoints with DMA capabilities". Or something along those lines.

How about write as below

PCI: endpoint: Enable DMA controller tests for endpoints with DMA capabilities

Some Endpoints controllers have DMA capabilities. This DMA controller has more efficiency then a general external DMA controller. And this DMA controller can bypass
outbound memory address translation unit.

The whole flow use standard DMA usage module

Quoted 11 lines

1. Using dma_request_channel() and filter function to find correct RX and TX Channel. if not exist, failure back to try allocate
general DMA controller
channel.
2. dmaengine_slave_config() config remote side physcial address.
3. using dmaengine_prep_slave_single() create transfer descriptor
4. tx_submit();
5. dma_async_issue_pending();
.
best regards
Frank Li

@Lorenzo do you satisfy the above commit message?

Quoted 220 lines
Quoted 220 lines

Lorenzo

Quoted 217 lines

---
Change from v6 to v9:
- none
Change from v5 to v6:
- change subject
Change from v4 to v5:
- none
Change from v3 to v4:
- reverse Xmas tree order
- local -> dma_local
- change error message
- IS_ERR -> IS_ERR_OR_NULL
- check return value of dmaengine_slave_config()
Change from v1 to v2:
- none

 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++++++--
 1 file changed, 98 insertions(+), 10 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +98 -11
index 90d84d3bc868f..f26afd02f3a86 100644
@@ -52,9 +52,11 @@ struct pci_epf_test {
      enum pci_barno          test_reg_bar;
      size_t                  msix_table_offset;
      struct delayed_work     cmd_handler;
-     struct dma_chan         *dma_chan;
+     struct dma_chan         *dma_chan_tx;
+     struct dma_chan         *dma_chan_rx;
      struct completion       transfer_complete;
      bool                    dma_supported;
+     bool                    dma_private;
      const struct pci_epc_features *epc_features;
 };
 
@@ -105,12 +107,15 @@ static void pci_epf_test_dma_callback(void *param)
  */
 static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
                                    dma_addr_t dma_dst, dma_addr_t dma_src,
-                                   size_t len)
+                                   size_t len, dma_addr_t dma_remote,
+                                   enum dma_transfer_direction dir)
 {
+     struct dma_chan *chan = (dir == DMA_DEV_TO_MEM) ? epf_test->dma_chan_tx : epf_test->dma_chan_rx;
+     dma_addr_t dma_local = (dir == DMA_MEM_TO_DEV) ? dma_src : dma_dst;
      enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
-     struct dma_chan *chan = epf_test->dma_chan;
      struct pci_epf *epf = epf_test->epf;
      struct dma_async_tx_descriptor *tx;
+     struct dma_slave_config sconf = {};
      struct device *dev = &epf->dev;
      dma_cookie_t cookie;
      int ret;
@@ -120,7 +125,22 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
              return -EINVAL;
      }
 
-     tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+     if (epf_test->dma_private) {
+             sconf.direction = dir;
+             if (dir == DMA_MEM_TO_DEV)
+                     sconf.dst_addr = dma_remote;
+             else
+                     sconf.src_addr = dma_remote;
+
+             if (dmaengine_slave_config(chan, &sconf)) {
+                     dev_err(dev, "DMA slave config fail\n");
+                     return -EIO;
+             }
+             tx = dmaengine_prep_slave_single(chan, dma_local, len, dir, flags);
+     } else {
+             tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+     }
+
      if (!tx) {
              dev_err(dev, "Failed to prepare DMA memcpy\n");
              return -EIO;
@@ -148,6 +168,23 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
      return 0;
 }
 
+struct epf_dma_filter {
+     struct device *dev;
+     u32 dma_mask;
+};
+
+static bool epf_dma_filter_fn(struct dma_chan *chan, void *node)
+{
+     struct epf_dma_filter *filter = node;
+     struct dma_slave_caps caps;
+
+     memset(&caps, 0, sizeof(caps));
+     dma_get_slave_caps(chan, &caps);
+
+     return chan->device->dev == filter->dev
+             && (filter->dma_mask & caps.directions);
+}
+
 /**
  * pci_epf_test_init_dma_chan() - Function to initialize EPF test DMA channel
  * @epf_test: the EPF test device that performs data transfer operation
@@ -158,10 +195,44 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 {
      struct pci_epf *epf = epf_test->epf;
      struct device *dev = &epf->dev;
+     struct epf_dma_filter filter;
      struct dma_chan *dma_chan;
      dma_cap_mask_t mask;
      int ret;
 
+     filter.dev = epf->epc->dev.parent;
+     filter.dma_mask = BIT(DMA_DEV_TO_MEM);
+
+     dma_cap_zero(mask);
+     dma_cap_set(DMA_SLAVE, mask);
+     dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+     if (IS_ERR_OR_NULL(dma_chan)) {
+             dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+             goto fail_back_tx;
+     }
+
+     epf_test->dma_chan_rx = dma_chan;
+
+     filter.dma_mask = BIT(DMA_MEM_TO_DEV);
+     dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+
+     if (IS_ERR(dma_chan)) {
+             dev_info(dev, "Failed to get private DMA channel. Falling back to generic one\n");
+             goto fail_back_rx;
+     }
+
+     epf_test->dma_chan_tx = dma_chan;
+     epf_test->dma_private = true;
+
+     init_completion(&epf_test->transfer_complete);
+
+     return 0;
+
+fail_back_rx:
+     dma_release_channel(epf_test->dma_chan_rx);
+     epf_test->dma_chan_tx = NULL;
+
+fail_back_tx:
      dma_cap_zero(mask);
      dma_cap_set(DMA_MEMCPY, mask);
 
@@ -174,7 +245,7 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
      }
      init_completion(&epf_test->transfer_complete);
 
-     epf_test->dma_chan = dma_chan;
+     epf_test->dma_chan_tx = epf_test->dma_chan_rx = dma_chan;
 
      return 0;
 }
@@ -190,8 +261,17 @@ static void pci_epf_test_clean_dma_chan(struct pci_epf_test *epf_test)
      if (!epf_test->dma_supported)
              return;
 
-     dma_release_channel(epf_test->dma_chan);
-     epf_test->dma_chan = NULL;
+     dma_release_channel(epf_test->dma_chan_tx);
+     if (epf_test->dma_chan_tx == epf_test->dma_chan_rx) {
+             epf_test->dma_chan_tx = NULL;
+             epf_test->dma_chan_rx = NULL;
+             return;
+     }
+
+     dma_release_channel(epf_test->dma_chan_rx);
+     epf_test->dma_chan_rx = NULL;
+
+     return;
 }
 
 static void pci_epf_test_print_rate(const char *ops, u64 size,
@@ -280,8 +360,14 @@ static int pci_epf_test_copy(struct pci_epf_test *epf_test)
                      goto err_map_addr;
              }
 
+             if (epf_test->dma_private) {
+                     dev_err(dev, "Cannot transfer data using DMA\n");
+                     ret = -EINVAL;
+                     goto err_map_addr;
+             }
+
              ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-                                              src_phys_addr, reg->size);
+                                              src_phys_addr, reg->size, 0, DMA_MEM_TO_MEM);
              if (ret)
                      dev_err(dev, "Data transfer failed\n");
      } else {
@@ -363,7 +449,8 @@ static int pci_epf_test_read(struct pci_epf_test *epf_test)
 
              ktime_get_ts64(&start);
              ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-                                              phys_addr, reg->size);
+                                              phys_addr, reg->size,
+                                              reg->src_addr, DMA_DEV_TO_MEM);
              if (ret)
                      dev_err(dev, "Data transfer failed\n");
              ktime_get_ts64(&end);
@@ -453,8 +540,9 @@ static int pci_epf_test_write(struct pci_epf_test *epf_test)
              }
 
              ktime_get_ts64(&start);
+
              ret = pci_epf_test_data_transfer(epf_test, phys_addr,
-                                              src_phys_addr, reg->size);
+                                              src_phys_addr, reg->size, reg->dst_addr, DMA_MEM_TO_DEV);
              if (ret)
                      dev_err(dev, "Data transfer failed\n");
              ktime_get_ts64(&end);
--

2.35.1

Tested-by on the v9 series
#24 lore raw
In reply to Frank Li

Hello folks,

My review is finally over. Aside with that I've tested the series on Baikal-T1 SoC, which has DW PCIe Host controller v4.60 and DW eDMA embedded. A test was performed on kernel v5.18-rc3 by a simple driver copying random data from system memory to SM768 framebuffer and vise-versa. So @Frank feel free to add my tag to the entire series:

@Lorenzo, @Rob, @Vinod, my patchset:

is based on this one. In its turn my series depends on the other patchsets:
[PATCH v2 0/4] clk: Baikal-T1 DDR/PCIe resets and some xGMAC fixes

[PATCH 00/12] PCI: dwc: Various fixes and cleanups

[PATCH 00/16] PCI: dwc: Add dma-ranges/YAML-schema/Baikal-T1 support
https://lore.kernel.org/linux-pci/[email protected]
which are currently on review. (BTW @Rob I am waiting for your responses there to go on with v2 re-spin.) I am very much eager to get my patches ready before the next merge windows. But in order to preserve the consistency of the corresponding repo with my patchsets it needs to have the @Frank' patches. Seeing aside with @Frank's series my changes depends on the changes in the clk and pci subsystems, could you please consider choosing a single repository for merging all my and @Frank patches in. Since the changes mostly concern the DW PCIe controller I suggest to use the 'pci/dwc' branch of the 'kernel/git/lpieralisi/pci.git' repository. What do you think? @Lorenzo?

-Sergey

Quoted 54 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (7):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags
PCI: endpoint: Add embedded DMA controller test

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 139 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  54 ++++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  10 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 8 files changed, 312 insertions(+), 176 deletions(-)
Signature · 1 line
2.35.1
#25 lore raw
Quoted 10 lines · Serge Semin

Hello folks,

My review is finally over. Aside with that I've tested the series on Baikal-T1 SoC, which has DW PCIe Host controller v4.60 and DW eDMA embedded. A test was performed on kernel v5.18-rc3 by a simple driver copying random data from system memory to SM768 framebuffer and vise-versa. So @Frank feel free to add my tag to the entire series:

Thanks. I think the maintainer can add this when they pick up the patches. I will add it if patches need to be respin.

best regards
Frank Li

Quoted 80 lines

@Lorenzo, @Rob, @Vinod, my patchset:

is based on this one. In its turn my series depends on the other patchsets:
[PATCH v2 0/4] clk: Baikal-T1 DDR/PCIe resets and some xGMAC fixes

[PATCH 00/12] PCI: dwc: Various fixes and cleanups

[PATCH 00/16] PCI: dwc: Add dma-ranges/YAML-schema/Baikal-T1 support
https://lore.kernel.org/linux-pci/[email protected]
which are currently on review. (BTW @Rob I am waiting for your responses there to go on with v2 re-spin.) I am very much eager to get my patches ready before the next merge windows. But in order to preserve the consistency of the corresponding repo with my patchsets it needs to have the @Frank' patches. Seeing aside with @Frank's series my changes depends on the changes in the clk and pci subsystems, could you please consider choosing a single repository for merging all my and @Frank patches in. Since the changes mostly concern the DW PCIe controller I suggest to use the 'pci/dwc' branch of the 'kernel/git/lpieralisi/pci.git' repository. What do you think? @Lorenzo?

-Sergey

Quoted 54 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (7):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags
PCI: endpoint: Add embedded DMA controller test

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 139 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  54 ++++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  10 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 8 files changed, 312 insertions(+), 176 deletions(-)

--
2.35.1

#26 lore raw
Quoted 10 lines · Zhi Li
Quoted 9 lines · Serge Semin

Hello folks,

My review is finally over. Aside with that I've tested the series on Baikal-T1 SoC, which has DW PCIe Host controller v4.60 and DW eDMA embedded. A test was performed on kernel v5.18-rc3 by a simple driver copying random data from system memory to SM768 framebuffer and vise-versa. So @Frank feel free to add my tag to the entire series:

Quoted 5 lines
Quoted 1 line

Thanks. I think the maintainer can add this when they pick up the patches. I will add it if patches need to be respin.

Right, 'b4 am -t' does the trick.

-Sergey

Quoted 84 lines

best regards
Frank Li

Quoted 80 lines

@Lorenzo, @Rob, @Vinod, my patchset:

is based on this one. In its turn my series depends on the other patchsets:
[PATCH v2 0/4] clk: Baikal-T1 DDR/PCIe resets and some xGMAC fixes

[PATCH 00/12] PCI: dwc: Various fixes and cleanups

[PATCH 00/16] PCI: dwc: Add dma-ranges/YAML-schema/Baikal-T1 support
https://lore.kernel.org/linux-pci/[email protected]
which are currently on review. (BTW @Rob I am waiting for your responses there to go on with v2 re-spin.) I am very much eager to get my patches ready before the next merge windows. But in order to preserve the consistency of the corresponding repo with my patchsets it needs to have the @Frank' patches. Seeing aside with @Frank's series my changes depends on the changes in the clk and pci subsystems, could you please consider choosing a single repository for merging all my and @Frank patches in. Since the changes mostly concern the DW PCIe controller I suggest to use the 'pci/dwc' branch of the 'kernel/git/lpieralisi/pci.git' repository. What do you think? @Lorenzo?

-Sergey

Quoted 54 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (7):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific flags
PCI: endpoint: Add embedded DMA controller test

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 139 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  54 ++++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  10 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 108 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 8 files changed, 312 insertions(+), 176 deletions(-)

--
2.35.1