Skip to contentSkip to conversation

Enable designware PCI EP EDMA locally

PATCH Applied Frank Li 5 participants 24 messages May 24, 2022 – Jun 16, 2022

Subsystems (4)
lore
Share & tools
lore

Frank Li

author
#0 lore raw

v12 cover Enable designware PCI EP EDMA locally

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)
Signature · 1 line
2.35.1
author
#1 lore raw

PATCH v12 1/8 dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip

irq of struct dw_edma_chip was never used.
It can be removed safely.

---
Change from v7 to v12
- None
Change from v6 to v7
- move to 1st patch
Change from v5 to v6
- s/remove/Remove/ at subject
Change from v4 to v5
- none
new patch at v4

 drivers/dma/dw-edma/dw-edma-pcie.c | 1 -
 include/linux/dma/edma.h           | 2 --
 2 files changed, 3 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +0 -1
index 44f6e09bdb531..b8f52ca10fa91 100644
@@ -231,7 +231,6 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->dw = dw;
 	chip->dev = dev;
 	chip->id = pdev->devfn;
-	chip->irq = pdev->irq;
 
 	dw->mf = vsec_data.mf;
 	dw->nr_irqs = nr_irqs;
include/linux/dma/edma.h +0 -2
index cab6e18773dad..d4333e721588d 100644
@@ -18,13 +18,11 @@ struct dw_edma;
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
- * @irq:		 irq line
  * @dw:			 struct dw_edma that is filed by dw_edma_probe()
  */
 struct dw_edma_chip {
 	struct device		*dev;
 	int			id;
-	int			irq;
 	struct dw_edma		*dw;
 };
 
Signature · 1 line
2.35.1
author
#2 lore raw

PATCH v12 2/8 dmaengine: dw-edma: Detach the private data and chip info structures

In reply to Frank Li

"struct dw_edma_chip" contains an internal structure "struct dw_edma" that is used by the eDMA core internally. This structure should not be touched by the eDMA controller drivers themselves. But currently, the eDMA controller drivers like "dw-edma-pci" allocates and populates this internal structure then passes it on to eDMA core. The eDMA core further populates the structure and uses it. This is wrong!

Hence, move all the "struct dw_edma" specifics from controller drivers to the eDMA core.

---
Change from v10 to v12
none
Change from v9 to v10
- add doc for dt_region_wr/dt_region_rd

Change from v8 to v9
- remove chip->ops check at dw_edma_irq_request()

Change from v7 to v8
- Check chip->ops at probe()
- use struct edma_dw at dw_edma_v0_debugfs_on/off()

Change from v6 to v7
- Move nr_irqs and chip->ops check into dw_edma_irq_request()
- Move dw->irq devm_kcalloc() into dw_edma_irq_request()
- Change dw->nr_irqs after request success
- Fix wrong use chip->nr_irqs when remove

Change from v5 to v6
- Don't touch chip->nr_irqs
- Don't set chip->dw utill everything is okay
- dw_edma_channel_setup() and dw_edma_v0_core_debugfs_on/off() methods take
dw_edma structure pointer as a parameter

Change from v4 to v5
- Move chip->nr_irqs before allocate dw_edma
Change from v3 to v4
- Accept most suggestions of Serge Semin
Change from v2 to v3
- none
Change from v1 to v2
- rework commit message
- remove duplicate field in struct dw_edma

 drivers/dma/dw-edma/dw-edma-core.c       | 90 +++++++++++++-----------
 drivers/dma/dw-edma/dw-edma-core.h       | 31 +-------
 drivers/dma/dw-edma/dw-edma-pcie.c       | 82 +++++++++------------
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 32 ++++-----
 drivers/dma/dw-edma/dw-edma-v0-core.h    |  4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 18 ++---
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h |  8 +--
 include/linux/dma/edma.h                 | 46 ++++++++++++
 8 files changed, 163 insertions(+), 148 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +49 -41
index 53289927dd0d6..58e91fe384282 100644
@@ -64,8 +64,8 @@ static struct dw_edma_burst *dw_edma_alloc_burst(struct dw_edma_chunk *chunk)
 
 static struct dw_edma_chunk *dw_edma_alloc_chunk(struct dw_edma_desc *desc)
 {
+	struct dw_edma_chip *chip = desc->chan->dw->chip;
 	struct dw_edma_chan *chan = desc->chan;
-	struct dw_edma *dw = chan->chip->dw;
 	struct dw_edma_chunk *chunk;
 
 	chunk = kzalloc(sizeof(*chunk), GFP_NOWAIT);
@@ -82,11 +82,11 @@ static struct dw_edma_chunk *dw_edma_alloc_chunk(struct dw_edma_desc *desc)
 	 */
 	chunk->cb = !(desc->chunks_alloc % 2);
 	if (chan->dir == EDMA_DIR_WRITE) {
-		chunk->ll_region.paddr = dw->ll_region_wr[chan->id].paddr;
-		chunk->ll_region.vaddr = dw->ll_region_wr[chan->id].vaddr;
+		chunk->ll_region.paddr = chip->ll_region_wr[chan->id].paddr;
+		chunk->ll_region.vaddr = chip->ll_region_wr[chan->id].vaddr;
 	} else {
-		chunk->ll_region.paddr = dw->ll_region_rd[chan->id].paddr;
-		chunk->ll_region.vaddr = dw->ll_region_rd[chan->id].vaddr;
+		chunk->ll_region.paddr = chip->ll_region_rd[chan->id].paddr;
+		chunk->ll_region.vaddr = chip->ll_region_rd[chan->id].vaddr;
 	}
 
 	if (desc->chunk) {
@@ -664,7 +664,7 @@ static int dw_edma_alloc_chan_resources(struct dma_chan *dchan)
 	if (chan->status != EDMA_ST_IDLE)
 		return -EBUSY;
 
-	pm_runtime_get(chan->chip->dev);
+	pm_runtime_get(chan->dw->chip->dev);
 
 	return 0;
 }
@@ -686,15 +686,15 @@ static void dw_edma_free_chan_resources(struct dma_chan *dchan)
 		cpu_relax();
 	}
 
-	pm_runtime_put(chan->chip->dev);
+	pm_runtime_put(chan->dw->chip->dev);
 }
 
-static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
+static int dw_edma_channel_setup(struct dw_edma *dw, bool write,
 				 u32 wr_alloc, u32 rd_alloc)
 {
+	struct dw_edma_chip *chip = dw->chip;
 	struct dw_edma_region *dt_region;
 	struct device *dev = chip->dev;
-	struct dw_edma *dw = chip->dw;
 	struct dw_edma_chan *chan;
 	struct dw_edma_irq *irq;
 	struct dma_device *dma;
@@ -727,7 +727,7 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 
 		chan->vc.chan.private = dt_region;
 
-		chan->chip = chip;
+		chan->dw = dw;
 		chan->id = j;
 		chan->dir = write ? EDMA_DIR_WRITE : EDMA_DIR_READ;
 		chan->configured = false;
@@ -735,9 +735,9 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 		chan->status = EDMA_ST_IDLE;
 
 		if (write)
-			chan->ll_max = (dw->ll_region_wr[j].sz / EDMA_LL_SZ);
+			chan->ll_max = (chip->ll_region_wr[j].sz / EDMA_LL_SZ);
 		else
-			chan->ll_max = (dw->ll_region_rd[j].sz / EDMA_LL_SZ);
+			chan->ll_max = (chip->ll_region_rd[j].sz / EDMA_LL_SZ);
 		chan->ll_max -= 1;
 
 		dev_vdbg(dev, "L. List:\tChannel %s[%u] max_cnt=%u\n",
@@ -767,13 +767,13 @@ static int dw_edma_channel_setup(struct dw_edma_chip *chip, bool write,
 		vchan_init(&chan->vc, dma);
 
 		if (write) {
-			dt_region->paddr = dw->dt_region_wr[j].paddr;
-			dt_region->vaddr = dw->dt_region_wr[j].vaddr;
-			dt_region->sz = dw->dt_region_wr[j].sz;
+			dt_region->paddr = chip->dt_region_wr[j].paddr;
+			dt_region->vaddr = chip->dt_region_wr[j].vaddr;
+			dt_region->sz = chip->dt_region_wr[j].sz;
 		} else {
-			dt_region->paddr = dw->dt_region_rd[j].paddr;
-			dt_region->vaddr = dw->dt_region_rd[j].vaddr;
-			dt_region->sz = dw->dt_region_rd[j].sz;
+			dt_region->paddr = chip->dt_region_rd[j].paddr;
+			dt_region->vaddr = chip->dt_region_rd[j].vaddr;
+			dt_region->sz = chip->dt_region_rd[j].sz;
 		}
 
 		dw_edma_v0_core_device_config(chan);
@@ -827,11 +827,11 @@ static inline void dw_edma_add_irq_mask(u32 *mask, u32 alloc, u16 cnt)
 		(*mask)++;
 }
 
-static int dw_edma_irq_request(struct dw_edma_chip *chip,
+static int dw_edma_irq_request(struct dw_edma *dw,
 			       u32 *wr_alloc, u32 *rd_alloc)
 {
-	struct device *dev = chip->dev;
-	struct dw_edma *dw = chip->dw;
+	struct dw_edma_chip *chip = dw->chip;
+	struct device *dev = dw->chip->dev;
 	u32 wr_mask = 1;
 	u32 rd_mask = 1;
 	int i, err = 0;
@@ -840,12 +840,16 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 
 	ch_cnt = dw->wr_ch_cnt + dw->rd_ch_cnt;
 
-	if (dw->nr_irqs < 1)
+	if (chip->nr_irqs < 1 || !chip->ops->irq_vector)
 		return -EINVAL;
 
-	if (dw->nr_irqs == 1) {
+	dw->irq = devm_kcalloc(dev, chip->nr_irqs, sizeof(*dw->irq), GFP_KERNEL);
+	if (!dw->irq)
+		return -ENOMEM;
+
+	if (chip->nr_irqs == 1) {
 		/* Common IRQ shared among all channels */
-		irq = dw->ops->irq_vector(dev, 0);
+		irq = chip->ops->irq_vector(dev, 0);
 		err = request_irq(irq, dw_edma_interrupt_common,
 				  IRQF_SHARED, dw->name, &dw->irq[0]);
 		if (err) {
@@ -855,9 +859,11 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 
 		if (irq_get_msi_desc(irq))
 			get_cached_msi_msg(irq, &dw->irq[0].msi);
+
+		dw->nr_irqs = 1;
 	} else {
 		/* Distribute IRQs equally among all channels */
-		int tmp = dw->nr_irqs;
+		int tmp = chip->nr_irqs;
 
 		while (tmp && (*wr_alloc + *rd_alloc) < ch_cnt) {
 			dw_edma_dec_irq_alloc(&tmp, wr_alloc, dw->wr_ch_cnt);
@@ -868,7 +874,7 @@ static int dw_edma_irq_request(struct dw_edma_chip *chip,
 		dw_edma_add_irq_mask(&rd_mask, *rd_alloc, dw->rd_ch_cnt);
 
 		for (i = 0; i < (*wr_alloc + *rd_alloc); i++) {
-			irq = dw->ops->irq_vector(dev, i);
+			irq = chip->ops->irq_vector(dev, i);
 			err = request_irq(irq,
 					  i < *wr_alloc ?
 						dw_edma_interrupt_write :
@@ -902,20 +908,22 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 		return -EINVAL;
 
 	dev = chip->dev;
-	if (!dev)
+	if (!dev || !chip->ops)
 		return -EINVAL;
 
-	dw = chip->dw;
-	if (!dw || !dw->irq || !dw->ops || !dw->ops->irq_vector)
-		return -EINVAL;
+	dw = devm_kzalloc(dev, sizeof(*dw), GFP_KERNEL);
+	if (!dw)
+		return -ENOMEM;
+
+	dw->chip = chip;
 
 	raw_spin_lock_init(&dw->lock);
 
-	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt,
+	dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
 	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt,
+	dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
 	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
@@ -937,17 +945,17 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 	dw_edma_v0_core_off(dw);
 
 	/* Request IRQs */
-	err = dw_edma_irq_request(chip, &wr_alloc, &rd_alloc);
+	err = dw_edma_irq_request(dw, &wr_alloc, &rd_alloc);
 	if (err)
 		return err;
 
 	/* Setup write channels */
-	err = dw_edma_channel_setup(chip, true, wr_alloc, rd_alloc);
+	err = dw_edma_channel_setup(dw, true, wr_alloc, rd_alloc);
 	if (err)
 		goto err_irq_free;
 
 	/* Setup read channels */
-	err = dw_edma_channel_setup(chip, false, wr_alloc, rd_alloc);
+	err = dw_edma_channel_setup(dw, false, wr_alloc, rd_alloc);
 	if (err)
 		goto err_irq_free;
 
@@ -955,15 +963,15 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 	pm_runtime_enable(dev);
 
 	/* Turn debugfs on */
-	dw_edma_v0_core_debugfs_on(chip);
+	dw_edma_v0_core_debugfs_on(dw);
+
+	chip->dw = dw;
 
 	return 0;
 
 err_irq_free:
 	for (i = (dw->nr_irqs - 1); i >= 0; i--)
-		free_irq(dw->ops->irq_vector(dev, i), &dw->irq[i]);
-
-	dw->nr_irqs = 0;
+		free_irq(chip->ops->irq_vector(dev, i), &dw->irq[i]);
 
 	return err;
 }
@@ -981,7 +989,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)
 
 	/* Free irqs */
 	for (i = (dw->nr_irqs - 1); i >= 0; i--)
-		free_irq(dw->ops->irq_vector(dev, i), &dw->irq[i]);
+		free_irq(chip->ops->irq_vector(dev, i), &dw->irq[i]);
 
 	/* Power management */
 	pm_runtime_disable(dev);
@@ -1002,7 +1010,7 @@ int dw_edma_remove(struct dw_edma_chip *chip)
 	}
 
 	/* Turn debugfs off */
-	dw_edma_v0_core_debugfs_off(chip);
+	dw_edma_v0_core_debugfs_off(dw);
 
 	return 0;
 }
drivers/dma/dw-edma/dw-edma-core.h +3 -28
index 60316d408c3e0..85df2d511907b 100644
@@ -15,20 +15,12 @@
 #include "../virt-dma.h"
 
 #define EDMA_LL_SZ					24
-#define EDMA_MAX_WR_CH					8
-#define EDMA_MAX_RD_CH					8
 
 enum dw_edma_dir {
 	EDMA_DIR_WRITE = 0,
 	EDMA_DIR_READ
 };
 
-enum dw_edma_map_format {
-	EDMA_MF_EDMA_LEGACY = 0x0,
-	EDMA_MF_EDMA_UNROLL = 0x1,
-	EDMA_MF_HDMA_COMPAT = 0x5
-};
-
 enum dw_edma_request {
 	EDMA_REQ_NONE = 0,
 	EDMA_REQ_STOP,
@@ -57,12 +49,6 @@ struct dw_edma_burst {
 	u32				sz;
 };
 
-struct dw_edma_region {
-	phys_addr_t			paddr;
-	void				__iomem *vaddr;
-	size_t				sz;
-};
-
 struct dw_edma_chunk {
 	struct list_head		list;
 	struct dw_edma_chan		*chan;
@@ -87,7 +73,7 @@ struct dw_edma_desc {
 
 struct dw_edma_chan {
 	struct virt_dma_chan		vc;
-	struct dw_edma_chip		*chip;
+	struct dw_edma			*dw;
 	int				id;
 	enum dw_edma_dir		dir;
 
@@ -109,10 +95,6 @@ struct dw_edma_irq {
 	struct dw_edma			*dw;
 };
 
-struct dw_edma_core_ops {
-	int	(*irq_vector)(struct device *dev, unsigned int nr);
-};
-
 struct dw_edma {
 	char				name[20];
 
@@ -122,21 +104,14 @@ struct dw_edma {
 	struct dma_device		rd_edma;
 	u16				rd_ch_cnt;
 
-	struct dw_edma_region		rg_region;	/* Registers */
-	struct dw_edma_region		ll_region_wr[EDMA_MAX_WR_CH];
-	struct dw_edma_region		ll_region_rd[EDMA_MAX_RD_CH];
-	struct dw_edma_region		dt_region_wr[EDMA_MAX_WR_CH];
-	struct dw_edma_region		dt_region_rd[EDMA_MAX_RD_CH];
-
 	struct dw_edma_irq		*irq;
 	int				nr_irqs;
 
-	enum dw_edma_map_format		mf;
-
 	struct dw_edma_chan		*chan;
-	const struct dw_edma_core_ops	*ops;
 
 	raw_spinlock_t			lock;		/* Only for legacy */
+
+	struct dw_edma_chip             *chip;
 #ifdef CONFIG_DEBUG_FS
 	struct dentry			*debugfs;
 #endif /* CONFIG_DEBUG_FS */
drivers/dma/dw-edma/dw-edma-pcie.c +34 -48

143 lines not on this page · raw message

drivers/dma/dw-edma/dw-edma-v0-core.c +16 -16
index 33bc1e6c4cf2e..999e038961866 100644
@@ -25,7 +25,7 @@ enum dw_edma_control {
 
 static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 {
-	return dw->rg_region.vaddr;
+	return dw->chip->rg_region.vaddr;
 }
 
 #define SET_32(dw, name, value)				\
@@ -96,7 +96,7 @@ static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 static inline struct dw_edma_v0_ch_regs __iomem *
 __dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY)
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY)
 		return &(__dw_regs(dw)->type.legacy.ch);
 
 	if (dir == EDMA_DIR_WRITE)
@@ -108,7 +108,7 @@ __dw_ch_regs(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch)
 static inline void writel_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			     u32 value, void __iomem *addr)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -133,7 +133,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 {
 	u32 value;
 
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -169,7 +169,7 @@ static inline u32 readl_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 static inline void writeq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 			     u64 value, void __iomem *addr)
 {
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -194,7 +194,7 @@ static inline u64 readq_ch(struct dw_edma *dw, enum dw_edma_dir dir, u16 ch,
 {
 	u32 value;
 
-	if (dw->mf == EDMA_MF_EDMA_LEGACY) {
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY) {
 		u32 viewport_sel;
 		unsigned long flags;
 
@@ -256,7 +256,7 @@ u16 dw_edma_v0_core_ch_count(struct dw_edma *dw, enum dw_edma_dir dir)
 
 enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp;
 
 	tmp = FIELD_GET(EDMA_V0_CH_STATUS_MASK,
@@ -272,7 +272,7 @@ enum dma_status dw_edma_v0_core_ch_status(struct dw_edma_chan *chan)
 
 void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 
 	SET_RW_32(dw, chan->dir, int_clear,
 		  FIELD_PREP(EDMA_V0_DONE_INT_MASK, BIT(chan->id)));
@@ -280,7 +280,7 @@ void dw_edma_v0_core_clear_done_int(struct dw_edma_chan *chan)
 
 void dw_edma_v0_core_clear_abort_int(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 
 	SET_RW_32(dw, chan->dir, int_clear,
 		  FIELD_PREP(EDMA_V0_ABORT_INT_MASK, BIT(chan->id)));
@@ -357,7 +357,7 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 {
 	struct dw_edma_chan *chan = chunk->chan;
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp;
 
 	dw_edma_v0_core_write_chunk(chunk);
@@ -365,7 +365,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 	if (first) {
 		/* Enable engine */
 		SET_RW_32(dw, chan->dir, engine_en, BIT(0));
-		if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+		if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 			switch (chan->id) {
 			case 0:
 				SET_RW_COMPAT(dw, chan->dir, ch0_pwr_en,
@@ -435,7 +435,7 @@ void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first)
 
 int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)
 {
-	struct dw_edma *dw = chan->chip->dw;
+	struct dw_edma *dw = chan->dw;
 	u32 tmp = 0;
 
 	/* MSI done addr - low, high */
@@ -505,12 +505,12 @@ int dw_edma_v0_core_device_config(struct dw_edma_chan *chan)
 }
 
 /* eDMA debugfs callbacks */
-void dw_edma_v0_core_debugfs_on(struct dw_edma_chip *chip)
+void dw_edma_v0_core_debugfs_on(struct dw_edma *dw)
 {
-	dw_edma_v0_debugfs_on(chip);
+	dw_edma_v0_debugfs_on(dw);
 }
 
-void dw_edma_v0_core_debugfs_off(struct dw_edma_chip *chip)
+void dw_edma_v0_core_debugfs_off(struct dw_edma *dw)
 {
-	dw_edma_v0_debugfs_off(chip);
+	dw_edma_v0_debugfs_off(dw);
 }
drivers/dma/dw-edma/dw-edma-v0-core.h +2 -2
index 2afa626b8300c..75aec6d31b210 100644
@@ -22,7 +22,7 @@ u32 dw_edma_v0_core_status_abort_int(struct dw_edma *chan, enum dw_edma_dir dir)
 void dw_edma_v0_core_start(struct dw_edma_chunk *chunk, bool first);
 int dw_edma_v0_core_device_config(struct dw_edma_chan *chan);
 /* eDMA debug fs callbacks */
-void dw_edma_v0_core_debugfs_on(struct dw_edma_chip *chip);
-void dw_edma_v0_core_debugfs_off(struct dw_edma_chip *chip);
+void dw_edma_v0_core_debugfs_on(struct dw_edma *dw);
+void dw_edma_v0_core_debugfs_off(struct dw_edma *dw);
 
 #endif /* _DW_EDMA_V0_CORE_H */
drivers/dma/dw-edma/dw-edma-v0-debugfs.c +9 -9
index 4b3bcffd15ef1..b765adb969998 100644
@@ -54,7 +54,7 @@ struct debugfs_entries {
 static int dw_edma_debugfs_u32_get(void *data, u64 *val)
 {
 	void __iomem *reg = (void __force __iomem *)data;
-	if (dw->mf == EDMA_MF_EDMA_LEGACY &&
+	if (dw->chip->mf == EDMA_MF_EDMA_LEGACY &&
 	    reg >= (void __iomem *)&regs->type.legacy.ch) {
 		void __iomem *ptr = &regs->type.legacy.ch;
 		u32 viewport_sel = 0;
@@ -173,7 +173,7 @@ static void dw_edma_debugfs_regs_wr(struct dentry *dir)
 	nr_entries = ARRAY_SIZE(debugfs_regs);
 	dw_edma_debugfs_create_x32(debugfs_regs, nr_entries, regs_dir);
 
-	if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+	if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 		nr_entries = ARRAY_SIZE(debugfs_unroll_regs);
 		dw_edma_debugfs_create_x32(debugfs_unroll_regs, nr_entries,
 					   regs_dir);
@@ -242,7 +242,7 @@ static void dw_edma_debugfs_regs_rd(struct dentry *dir)
 	nr_entries = ARRAY_SIZE(debugfs_regs);
 	dw_edma_debugfs_create_x32(debugfs_regs, nr_entries, regs_dir);
 
-	if (dw->mf == EDMA_MF_HDMA_COMPAT) {
+	if (dw->chip->mf == EDMA_MF_HDMA_COMPAT) {
 		nr_entries = ARRAY_SIZE(debugfs_unroll_regs);
 		dw_edma_debugfs_create_x32(debugfs_unroll_regs, nr_entries,
 					   regs_dir);
@@ -282,13 +282,13 @@ static void dw_edma_debugfs_regs(void)
 	dw_edma_debugfs_regs_rd(regs_dir);
 }
 
-void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
+void dw_edma_v0_debugfs_on(struct dw_edma *_dw)
 {
-	dw = chip->dw;
+	dw = _dw;
 	if (!dw)
 		return;
 
-	regs = dw->rg_region.vaddr;
+	regs = dw->chip->rg_region.vaddr;
 	if (!regs)
 		return;
 
@@ -296,16 +296,16 @@ void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
 	if (!dw->debugfs)
 		return;
 
-	debugfs_create_u32("mf", 0444, dw->debugfs, &dw->mf);
+	debugfs_create_u32("mf", 0444, dw->debugfs, &dw->chip->mf);
 	debugfs_create_u16("wr_ch_cnt", 0444, dw->debugfs, &dw->wr_ch_cnt);
 	debugfs_create_u16("rd_ch_cnt", 0444, dw->debugfs, &dw->rd_ch_cnt);
 
 	dw_edma_debugfs_regs();
 }
 
-void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip)
+void dw_edma_v0_debugfs_off(struct dw_edma *_dw)
 {
-	dw = chip->dw;
+	dw = _dw;
 	if (!dw)
 		return;
 
drivers/dma/dw-edma/dw-edma-v0-debugfs.h +4 -4
index d0ff25a9ea5c9..3391b86edf5ab 100644
@@ -12,14 +12,14 @@
 #include <linux/dma/edma.h>
 
 #ifdef CONFIG_DEBUG_FS
-void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip);
-void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip);
+void dw_edma_v0_debugfs_on(struct dw_edma *dw);
+void dw_edma_v0_debugfs_off(struct dw_edma *dw);
 #else
-static inline void dw_edma_v0_debugfs_on(struct dw_edma_chip *chip)
+static inline void dw_edma_v0_debugfs_on(struct dw_edma *dw)
 {
 }
 
-static inline void dw_edma_v0_debugfs_off(struct dw_edma_chip *chip)
+static inline void dw_edma_v0_debugfs_off(struct dw_edma *dw)
 {
 }
 #endif /* CONFIG_DEBUG_FS */
include/linux/dma/edma.h +46 -0

63 lines not on this page · raw message

Signature · 1 line
2.35.1
author
#3 lore raw

PATCH v12 3/8 dmaengine: dw-edma: Change rg_region to reg_base in struct dw_edma_chip

In reply to Frank Li

struct dw_edma_region rg_region included virtual address, physical address and size information. But only virtual address is used by EDMA driver. Change it to void __iomem *reg_base to clean up code.

---
Change from v6 to v12:
- none
Change from v5 to v6:
-s/change/Change at subject
New patch at v4

 drivers/dma/dw-edma/dw-edma-pcie.c       | 6 +++---
 drivers/dma/dw-edma/dw-edma-v0-core.c    | 2 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c | 2 +-
 include/linux/dma/edma.h                 | 3 ++-
 4 files changed, 7 insertions(+), 6 deletions(-)
drivers/dma/dw-edma/dw-edma-pcie.c +3 -3
index 2c1c5fa4e9f28..ae42bad24dd5a 100644
@@ -233,8 +233,8 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
 	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
 
-	chip->rg_region.vaddr = pcim_iomap_table(pdev)[vsec_data.rg.bar];
-	if (!chip->rg_region.vaddr)
+	chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
+	if (!chip->reg_base)
 		return -ENOMEM;
 
 	for (i = 0; i < chip->wr_ch_cnt; i++) {
@@ -299,7 +299,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 
 	pci_dbg(pdev, "Registers:\tBAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p)\n",
 		vsec_data.rg.bar, vsec_data.rg.off, vsec_data.rg.sz,
-		chip->rg_region.vaddr);
+		chip->reg_base);
 
 
 	for (i = 0; i < chip->wr_ch_cnt; i++) {
drivers/dma/dw-edma/dw-edma-v0-core.c +1 -1
index 999e038961866..403ade40c1b1b 100644
@@ -25,7 +25,7 @@ enum dw_edma_control {
 
 static inline struct dw_edma_v0_regs __iomem *__dw_regs(struct dw_edma *dw)
 {
-	return dw->chip->rg_region.vaddr;
+	return dw->chip->reg_base;
 }
 
 #define SET_32(dw, name, value)				\
drivers/dma/dw-edma/dw-edma-v0-debugfs.c +1 -1
index b765adb969998..5226c9014703c 100644
@@ -288,7 +288,7 @@ void dw_edma_v0_debugfs_on(struct dw_edma *_dw)
 	if (!dw)
 		return;
 
-	regs = dw->chip->rg_region.vaddr;
+	regs = dw->chip->reg_base;
 	if (!regs)
 		return;
 
include/linux/dma/edma.h +2 -1
index 86697d33e0610..195ee1e47f21d 100644
@@ -39,6 +39,7 @@ enum dw_edma_map_format {
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @reg_base		 DMA register base address
  * @wr_ch_cnt		 DMA write channel number
  * @rd_ch_cnt		 DMA read channel number
  * @rg_region		 DMA register region
@@ -55,7 +56,7 @@ struct dw_edma_chip {
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
 
-	struct dw_edma_region	rg_region;
+	void __iomem		*reg_base;
 
 	u16			wr_ch_cnt;
 	u16			rd_ch_cnt;
Signature · 1 line
2.35.1
author
#4 lore raw

PATCH v12 4/8 dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct dw_edma_chip

In reply to Frank Li

There are same name wr(rd)_ch_cnt in struct dw_edma. EDMA driver get write(read) channel number from register, then save these into dw_edma. Old wr(rd)_ch_cnt in dw_edma_chip actuall means how many link list memory are available in ll_region_wr(rd)[EDMA_MAX_WR_CH]. So rename it to ll_wr(rd)_cnt to indicate actual usage.

---
Change from v10 to v12
- none
Change from v9 to v10
- Change comment for ll_wr(rd)_cnt
Change from v6 to v9
- none
Change from v5 to v6
- s/rename/Rename/ at subject
new patch at v4

 drivers/dma/dw-edma/dw-edma-core.c |  4 ++--
 drivers/dma/dw-edma/dw-edma-pcie.c | 12 ++++++------
 include/linux/dma/edma.h           |  8 ++++----
 3 files changed, 12 insertions(+), 12 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +2 -2
index 58e91fe384282..1ef326f7151a3 100644
@@ -919,11 +919,11 @@ int dw_edma_probe(struct dw_edma_chip *chip)
 
 	raw_spin_lock_init(&dw->lock);
 
-	dw->wr_ch_cnt = min_t(u16, chip->wr_ch_cnt,
+	dw->wr_ch_cnt = min_t(u16, chip->ll_wr_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_WRITE));
 	dw->wr_ch_cnt = min_t(u16, dw->wr_ch_cnt, EDMA_MAX_WR_CH);
 
-	dw->rd_ch_cnt = min_t(u16, chip->rd_ch_cnt,
+	dw->rd_ch_cnt = min_t(u16, chip->ll_rd_cnt,
 			      dw_edma_v0_core_ch_count(dw, EDMA_DIR_READ));
 	dw->rd_ch_cnt = min_t(u16, dw->rd_ch_cnt, EDMA_MAX_RD_CH);
 
drivers/dma/dw-edma/dw-edma-pcie.c +6 -6
index ae42bad24dd5a..7732537f96086 100644
@@ -230,14 +230,14 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 	chip->nr_irqs = nr_irqs;
 	chip->ops = &dw_edma_pcie_core_ops;
 
-	chip->wr_ch_cnt = vsec_data.wr_ch_cnt;
-	chip->rd_ch_cnt = vsec_data.rd_ch_cnt;
+	chip->ll_wr_cnt = vsec_data.wr_ch_cnt;
+	chip->ll_rd_cnt = vsec_data.rd_ch_cnt;
 
 	chip->reg_base = pcim_iomap_table(pdev)[vsec_data.rg.bar];
 	if (!chip->reg_base)
 		return -ENOMEM;
 
-	for (i = 0; i < chip->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_wr_cnt; i++) {
 		struct dw_edma_region *ll_region = &chip->ll_region_wr[i];
 		struct dw_edma_region *dt_region = &chip->dt_region_wr[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_wr[i];
@@ -262,7 +262,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		dt_region->sz = dt_block->sz;
 	}
 
-	for (i = 0; i < chip->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_rd_cnt; i++) {
 		struct dw_edma_region *ll_region = &chip->ll_region_rd[i];
 		struct dw_edma_region *dt_region = &chip->dt_region_rd[i];
 		struct dw_edma_block *ll_block = &vsec_data.ll_rd[i];
@@ -302,7 +302,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 		chip->reg_base);
 
 
-	for (i = 0; i < chip->wr_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_wr_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tWRITE CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_wr[i].bar,
 			vsec_data.ll_wr[i].off, chip->ll_region_wr[i].sz,
@@ -314,7 +314,7 @@ static int dw_edma_pcie_probe(struct pci_dev *pdev,
 			chip->dt_region_wr[i].vaddr, &chip->dt_region_wr[i].paddr);
 	}
 
-	for (i = 0; i < chip->rd_ch_cnt; i++) {
+	for (i = 0; i < chip->ll_rd_cnt; i++) {
 		pci_dbg(pdev, "L. List:\tREAD CH%.2u, BAR=%u, off=0x%.8lx, sz=0x%zx bytes, addr(v=%p, p=%pa)\n",
 			i, vsec_data.ll_rd[i].bar,
 			vsec_data.ll_rd[i].off, chip->ll_region_rd[i].sz,
include/linux/dma/edma.h +4 -4
index 195ee1e47f21d..c8b479f1d4da7 100644
@@ -40,8 +40,8 @@ enum dw_edma_map_format {
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
  * @reg_base		 DMA register base address
- * @wr_ch_cnt		 DMA write channel number
- * @rd_ch_cnt		 DMA read channel number
+ * @ll_wr_cnt		 DMA write link list count
+ * @ll_rd_cnt		 DMA read link list count
  * @rg_region		 DMA register region
  * @ll_region_wr	 DMA descriptor link list memory for write channel
  * @ll_region_rd	 DMA descriptor link list memory for read channel
@@ -58,8 +58,8 @@ struct dw_edma_chip {
 
 	void __iomem		*reg_base;
 
-	u16			wr_ch_cnt;
-	u16			rd_ch_cnt;
+	u16			ll_wr_cnt;
+	u16			ll_rd_cnt;
 	/* link list address */
 	struct dw_edma_region	ll_region_wr[EDMA_MAX_WR_CH];
 	struct dw_edma_region	ll_region_rd[EDMA_MAX_RD_CH];
Signature · 1 line
2.35.1
author
#5 lore raw

PATCH v12 5/8 dmaengine: dw-edma: Drop dma_slave_config.direction field usage

In reply to Frank Li

From: Serge Semin <[email protected]>

The dma_slave_config.direction field usage in the DW eDMA driver has been introduced in the commit bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics"). Mainly the change introduced there was correct (indeed DEV_TO_MEM means using RD-channel and MEM_TO_DEV - WR-channel for the case of having eDMA accessed locally from CPU/Application side), but providing an additional MEM_TO_MEM/DEV_TO_DEV-based semantics was quite redundant if not to say potentially harmful (when it comes to removing the denoted field). First of all since the dma_slave_config.direction field has been marked as obsolete (see [1] and the structure dc [2]) and will be discarded in future, using it especially in a non-standard way is discouraged. Secondly in accordance with the commit denoted above the default dw_edma_device_transfer() semantics has been changed despite what it's message said. So claiming that the method was left backward compatible was wrong.

Anyway let's fix the problems denoted above and simplify the dw_edma_device_transfer() method by dropping the parsing of the DMA-channel direction field. Instead of having that implicit dma_slave_config.direction field semantic we can use the recently added DW_EDMA_CHIP_LOCAL flag to distinguish between the local and remote DW eDMA setups thus preserving both cases support. In addition to that an ASCII-figure has been added to clarify the complication out.

[1] Documentation/driver-api/dmaengine/provider.rst
[2] include/linux/dmaengine.h: dma_slave_config.direction

---
 drivers/dma/dw-edma/dw-edma-core.c | 49 +++++++++++++++++++++---------
 1 file changed, 34 insertions(+), 15 deletions(-)
drivers/dma/dw-edma/dw-edma-core.c +34 -15
index 1ef326f7151a3..3ce0d7600da64 100644
@@ -340,21 +340,40 @@ dw_edma_device_transfer(struct dw_edma_transfer *xfer)
 	if (!chan->configured)
 		return NULL;
 
-	switch (chan->config.direction) {
-	case DMA_DEV_TO_MEM: /* local DMA */
-		if (dir == DMA_DEV_TO_MEM && chan->dir == EDMA_DIR_READ)
-			break;
-		return NULL;
-	case DMA_MEM_TO_DEV: /* local DMA */
-		if (dir == DMA_MEM_TO_DEV && chan->dir == EDMA_DIR_WRITE)
-			break;
-		return NULL;
-	default: /* remote DMA */
-		if (dir == DMA_MEM_TO_DEV && chan->dir == EDMA_DIR_READ)
-			break;
-		if (dir == DMA_DEV_TO_MEM && chan->dir == EDMA_DIR_WRITE)
-			break;
-		return NULL;
+	/*
+	 * Local Root Port/End-point              Remote End-point
+	 * +-----------------------+ PCIe bus +----------------------+
+	 * |                       |    +-+   |                      |
+	 * |    DEV_TO_MEM   Rx Ch <----+ +---+ Tx Ch  DEV_TO_MEM    |
+	 * |                       |    | |   |                      |
+	 * |    MEM_TO_DEV   Tx Ch +----+ +---> Rx Ch  MEM_TO_DEV    |
+	 * |                       |    +-+   |                      |
+	 * +-----------------------+          +----------------------+
+	 *
+	 * 1. Normal logic:
+	 * If eDMA is embedded into the DW PCIe RP/EP and controlled from the
+	 * CPU/Application side, the Rx channel (EDMA_DIR_READ) will be used
+	 * for the device read operations (DEV_TO_MEM) and the Tx channel
+	 * (EDMA_DIR_WRITE) - for the write operations (MEM_TO_DEV).
+	 *
+	 * 2. Inverted logic:
+	 * If eDMA is embedded into a Remote PCIe EP and is controlled by the
+	 * MWr/MRd TLPs sent from the CPU's PCIe host controller, the Tx
+	 * channel (EDMA_DIR_WRITE) will be used for the device read operations
+	 * (DEV_TO_MEM) and the Rx channel (EDMA_DIR_READ) - for the write
+	 * operations (MEM_TO_DEV).
+	 *
+	 * It is the client driver responsibility to choose a proper channel
+	 * for the DMA transfers.
+	 */
+	if (chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL) {
+		if ((chan->dir == EDMA_DIR_READ && dir != DMA_DEV_TO_MEM) ||
+		    (chan->dir == EDMA_DIR_WRITE && dir != DMA_MEM_TO_DEV))
+			return NULL;
+	} else {
+		if ((chan->dir == EDMA_DIR_WRITE && dir != DMA_DEV_TO_MEM) ||
+		    (chan->dir == EDMA_DIR_READ && dir != DMA_MEM_TO_DEV))
+			return NULL;
 	}
 
 	if (xfer->type == EDMA_XFER_CYCLIC) {
Signature · 1 line
2.35.1
author
#6 lore raw

PATCH v12 6/8 dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction semantics

In reply to Frank Li

From: Serge Semin <[email protected]>

In accordance with [1, 2] the DW eDMA controller has been created to be part of the DW PCIe Root Port and DW PCIe End-point controllers and to offload the transferring of large blocks of data between application and remote PCIe domains leaving the system CPU free for other tasks. In the first case (eDMA being part of DW PCIe Root Port) the eDMA controller is always accessible via the CPU DBI interface and never over the PCIe wire. The later case is more complex. Depending on the DW PCIe End-Point IP-core synthesize parameters it's possible to have the eDMA registers accessible not only from the application CPU side, but also via mapping the eDMA CSRs over a dedicated end-point BAR. So based on the specifics denoted above the eDMA driver is supposed to support two types of the DMA controller setups:
1) eDMA embedded into the DW PCIe Root Port/End-point and accessible over the local CPU from the application side.
2) eDMA embedded into the DW PCIe End-point and accessible via the PCIe wire with MWr/MRd TLPs generated by the CPU PCIe host controller. Since the CPU memory resides different sides in these cases the semantics of the MEM_TO_DEV and DEV_TO_MEM operations is flipped with respect to the Tx and Rx DMA channels. So MEM_TO_DEV/DEV_TO_MEM corresponds to the Tx/Rx channels in setup 1) and to the Rx/Tx channels in case of setup 2).

The DW eDMA driver has supported the case 2) since the initial commit e63d79d1ffcd ("dmaengine: Add Synopsys eDMA IP core driver") in the framework of the drivers/dma/dw-edma/dw-edma-pcie.c driver. The case 1) support was added a bit later in commit bd96f1b2f43a ("dmaengine: dw-edma:
support local dma device transfer semantics"). Afterwards the driver was supposed to cover the both possible eDMA setups, but the later commit turned to be not fully correct. The problem was that the commit together with the new functionality support also changed the channel direction semantics in a way so the eDMA Read-channel (corresponding to the DMA_DEV_TO_MEM direction for the case 1.) now uses the sgl/cyclic base addresses as the Source addresses of the DMA-transfers and dma_slave_config.dst_addr as the Destination address of the DMA-transfers. Similarly the eDMA Write-channel (corresponding to the DMA_MEM_TO_DEV direction for case 1.) now utilizes dma_slave_config.src_addr as a source address of the DMA-transfers and sgl/cyclic base address as the Destination address of the DMA-transfers. This contradicts to the logic of the DMA-interface, which implies that DEV side is supposed to belong to the PCIe device memory and MEM - to the CPU/Application memory. Indeed it seems irrational to have the SG-list defined in the PCIe bus space, while expecting a contiguous buffer allocated in the CPU memory. Moreover the passed SG-list and cyclic DMA buffers are supposed to be mapped in a way so to be seen by the DW eDMA Application (CPU) interface. So in order to have the correct DW eDMA interface we need to invert the eDMA Rd/Wr-channels and DMA-slave directions semantics by selecting the src/dst addresses based on the DMA transfer direction instead of using the channel direction capability.

[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port, v.5.40a, March 2019, p.1092
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Endpoint, v.5.40a, March 2019, p.1189

Fixes bd96f1b2f43a ("dmaengine: dw-edma: support local dma device transfer semantics")
---
 drivers/dma/dw-edma/dw-edma-core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/dma/dw-edma/dw-edma-core.c +1 -1
index 3ce0d7600da64..fa95d1d17db21 100644
@@ -443,7 +443,7 @@ dw_edma_device_transfer(struct dw_edma_transfer *xfer)
 		chunk->ll_region.sz += burst->sz;
 		desc->alloc_sz += burst->sz;
 
-		if (chan->dir == EDMA_DIR_WRITE) {
+		if (dir == DMA_DEV_TO_MEM) {
 			burst->sar = src_addr;
 			if (xfer->type == EDMA_XFER_CYCLIC) {
 				burst->dar = xfer->xfer.cyclic.paddr;
Signature · 1 line
2.35.1
author
#7 lore raw

PATCH v12 7/8 dmaengine: dw-edma: Add support for chip specific flags

In reply to Frank Li

Add a "flags" field to the "struct dw_edma_chip" so that the controller drivers can pass flags that are relevant to the platform.

DW_EDMA_CHIP_LOCAL - Used by the controller drivers accessing eDMA locally. Local eDMA access doesn't require generating MSIs to the remote.

---
Change from v7 to v12
-none
Change from v6 to v7
- dw_edma_chip_flags to u32
Change from v5 to v6
- use enum instead of define

Change from v4 to v5
- split two two patch
- rework commit message
Change from v3 to v4
none
Change from v2 to v3
- rework commit message
- Change to DW_EDMA_CHIP_32BIT_DBI
- using DW_EDMA_CHIP_LOCAL control msi
- Apply Bjorn's comments,

        if (!j) {
               control |= DW_EDMA_V0_LIE;
               if (!(chan->chip->flags & DW_EDMA_CHIP_LOCAL))
                               control |= DW_EDMA_V0_RIE;
        }

        if ((chan->chip->flags & DW_EDMA_CHIP_REG32BIT) ||
              !IS_ENABLED(CONFIG_64BIT)) {
          SET_CH_32(...);
          SET_CH_32(...);
       } else {
          SET_CH_64(...);
       }

Change from v1 to v2
- none

 drivers/dma/dw-edma/dw-edma-v0-core.c |  9 ++++++---
 include/linux/dma/edma.h              | 10 ++++++++++
 2 files changed, 16 insertions(+), 3 deletions(-)
drivers/dma/dw-edma/dw-edma-v0-core.c +6 -3
index 403ade40c1b1b..607647dacc291 100644
@@ -301,6 +301,7 @@ u32 dw_edma_v0_core_status_abort_int(struct dw_edma *dw, enum dw_edma_dir dir)
 static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 {
 	struct dw_edma_burst *child;
+	struct dw_edma_chan *chan = chunk->chan;
 	struct dw_edma_v0_lli __iomem *lli;
 	struct dw_edma_v0_llp __iomem *llp;
 	u32 control = 0, i = 0;
@@ -314,9 +315,11 @@ static void dw_edma_v0_core_write_chunk(struct dw_edma_chunk *chunk)
 	j = chunk->bursts_alloc;
 	list_for_each_entry(child, &chunk->burst->list, list) {
 		j--;
-		if (!j)
-			control |= (DW_EDMA_V0_LIE | DW_EDMA_V0_RIE);
-
+		if (!j) {
+			control |= DW_EDMA_V0_LIE;
+			if (!(chan->dw->chip->flags & DW_EDMA_CHIP_LOCAL))
+				control |= DW_EDMA_V0_RIE;
+		}
 		/* Channel control */
 		SET_LL_32(&lli[i].control, control);
 		/* Transfer size */
include/linux/dma/edma.h +10 -0
index c8b479f1d4da7..7baf16fd4f233 100644
@@ -33,12 +33,21 @@ enum dw_edma_map_format {
 	EDMA_MF_HDMA_COMPAT = 0x5
 };
 
+/**
+ * enum dw_edma_chip_flags - Flags specific to an eDMA chip
+ * @DW_EDMA_CHIP_LOCAL:		eDMA is used locally by an endpoint
+ */
+enum dw_edma_chip_flags {
+	DW_EDMA_CHIP_LOCAL	= BIT(0),
+};
+
 /**
  * struct dw_edma_chip - representation of DesignWare eDMA controller hardware
  * @dev:		 struct device of the eDMA controller
  * @id:			 instance ID
  * @nr_irqs:		 total dma irq number
  * @ops			 DMA channel to IRQ number mapping
+ * @flags		 dw_edma_chip_flags
  * @reg_base		 DMA register base address
  * @ll_wr_cnt		 DMA write link list count
  * @ll_rd_cnt		 DMA read link list count
@@ -55,6 +64,7 @@ struct dw_edma_chip {
 	int			id;
 	int			nr_irqs;
 	const struct dw_edma_core_ops   *ops;
+	u32			flags;
 
 	void __iomem		*reg_base;
 
Signature · 1 line
2.35.1
author
#8 lore raw

PATCH v12 8/8 PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

In reply to Frank Li

Some PCI Endpoint controllers integrate an eDMA (embedded DMA). eDMA can bypass the outbound memory address translation unit to access all RC memory space.

Add eDMA support for pci-epf-test.

Depending on HW availability, the EPF test can use either eDMA or general system DMA controllers to perform DMA. The test tries to use eDMA first and falls back to general system DMA controllers if there's no eDMA

Separate dma_chan to dma_chan_tx and dma_chan_rx. Search for an eDMA channel first, then search for a memory-to-memory DMA channel. If general memory to memory channels are used, dma_chan_rx = dma_chan_tx.

Add dma_addr_t dma_remote in pci_epf_test_data_transfer() because eDMA uses remote RC physical address directly.

Add enum dma_transfer_direction dir in pci_epf_test_data_transfer() because eDMA chooses the correct RX/TX channel by dir.

The overall steps are

1. Execute dma_request_channel() and filter function to find correct eDMA RX and TX Channel. If a channel does not exist, fallback to try to allocate general memory to memory DMA channel.
2. Execute dmaengine_slave_config() to configure remote side physical address.
3. Execute dmaengine_prep_slave_single() to create transfer descriptor.
4. Execute tx_submit().
5. Execute dma_async_issue_pending()

---
Change from v11 to v12:
- remrite commit message
- wrap code to 80 line
- difference error message when apply tx/rx channel
Change from v10 to v11:
- rewrite commit message
Change from v9 to v10:
- rewrite commit message
Change from v4 to v9:
- none
Change from v3 to v4:
- reverse Xmas tree order
- local -> dma_local
- change error message
- IS_ERR -> IS_ERR_OR_NULL
- check return value of dmaengine_slave_config()
Change from v1 to v2:
- none

 drivers/pci/endpoint/functions/pci-epf-test.c | 113 ++++++++++++++++--
 1 file changed, 103 insertions(+), 10 deletions(-)
drivers/pci/endpoint/functions/pci-epf-test.c +103 -10
index 90d84d3bc868f..f232dd8eb19f0 100644
@@ -52,9 +52,11 @@ struct pci_epf_test {
 	enum pci_barno		test_reg_bar;
 	size_t			msix_table_offset;
 	struct delayed_work	cmd_handler;
-	struct dma_chan		*dma_chan;
+	struct dma_chan		*dma_chan_tx;
+	struct dma_chan		*dma_chan_rx;
 	struct completion	transfer_complete;
 	bool			dma_supported;
+	bool			dma_private;
 	const struct pci_epc_features *epc_features;
 };
 
@@ -96,6 +98,8 @@ static void pci_epf_test_dma_callback(void *param)
  * @dma_src: The source address of the data transfer. It can be a physical
  *	     address given by pci_epc_mem_alloc_addr or DMA mapping APIs.
  * @len: The size of the data transfer
+ * @dma_remote: remote RC physical address
+ * @dir: DMA transfer direction
  *
  * Function that uses dmaengine API to transfer data between PCIe EP and remote
  * PCIe RC. The source and destination address can be a physical address given
@@ -105,12 +109,16 @@ static void pci_epf_test_dma_callback(void *param)
  */
 static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 				      dma_addr_t dma_dst, dma_addr_t dma_src,
-				      size_t len)
+				      size_t len, dma_addr_t dma_remote,
+				      enum dma_transfer_direction dir)
 {
+	struct dma_chan *chan = (dir == DMA_DEV_TO_MEM) ?
+				 epf_test->dma_chan_tx : epf_test->dma_chan_rx;
+	dma_addr_t dma_local = (dir == DMA_MEM_TO_DEV) ? dma_src : dma_dst;
 	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
-	struct dma_chan *chan = epf_test->dma_chan;
 	struct pci_epf *epf = epf_test->epf;
 	struct dma_async_tx_descriptor *tx;
+	struct dma_slave_config sconf = {};
 	struct device *dev = &epf->dev;
 	dma_cookie_t cookie;
 	int ret;
@@ -120,7 +128,22 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 		return -EINVAL;
 	}
 
-	tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	if (epf_test->dma_private) {
+		sconf.direction = dir;
+		if (dir == DMA_MEM_TO_DEV)
+			sconf.dst_addr = dma_remote;
+		else
+			sconf.src_addr = dma_remote;
+
+		if (dmaengine_slave_config(chan, &sconf)) {
+			dev_err(dev, "DMA slave config fail\n");
+			return -EIO;
+		}
+		tx = dmaengine_prep_slave_single(chan, dma_local, len, dir, flags);
+	} else {
+		tx = dmaengine_prep_dma_memcpy(chan, dma_dst, dma_src, len, flags);
+	}
+
 	if (!tx) {
 		dev_err(dev, "Failed to prepare DMA memcpy\n");
 		return -EIO;
@@ -148,6 +171,23 @@ static int pci_epf_test_data_transfer(struct pci_epf_test *epf_test,
 	return 0;
 }
 
+struct epf_dma_filter {
+	struct device *dev;
+	u32 dma_mask;
+};
+
+static bool epf_dma_filter_fn(struct dma_chan *chan, void *node)
+{
+	struct epf_dma_filter *filter = node;
+	struct dma_slave_caps caps;
+
+	memset(&caps, 0, sizeof(caps));
+	dma_get_slave_caps(chan, &caps);
+
+	return chan->device->dev == filter->dev
+		&& (filter->dma_mask & caps.directions);
+}
+
 /**
  * pci_epf_test_init_dma_chan() - Function to initialize EPF test DMA channel
  * @epf_test: the EPF test device that performs data transfer operation
@@ -158,10 +198,44 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 {
 	struct pci_epf *epf = epf_test->epf;
 	struct device *dev = &epf->dev;
+	struct epf_dma_filter filter;
 	struct dma_chan *dma_chan;
 	dma_cap_mask_t mask;
 	int ret;
 
+	filter.dev = epf->epc->dev.parent;
+	filter.dma_mask = BIT(DMA_DEV_TO_MEM);
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_SLAVE, mask);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+	if (IS_ERR_OR_NULL(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA rx channel. Falling back to generic one\n");
+		goto fail_back_tx;
+	}
+
+	epf_test->dma_chan_rx = dma_chan;
+
+	filter.dma_mask = BIT(DMA_MEM_TO_DEV);
+	dma_chan = dma_request_channel(mask, epf_dma_filter_fn, &filter);
+
+	if (IS_ERR(dma_chan)) {
+		dev_info(dev, "Failed to get private DMA tx channel. Falling back to generic one\n");
+		goto fail_back_rx;
+	}
+
+	epf_test->dma_chan_tx = dma_chan;
+	epf_test->dma_private = true;
+
+	init_completion(&epf_test->transfer_complete);
+
+	return 0;
+
+fail_back_rx:
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_tx = NULL;
+
+fail_back_tx:
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_MEMCPY, mask);
 
@@ -174,7 +248,7 @@ static int pci_epf_test_init_dma_chan(struct pci_epf_test *epf_test)
 	}
 	init_completion(&epf_test->transfer_complete);
 
-	epf_test->dma_chan = dma_chan;
+	epf_test->dma_chan_tx = epf_test->dma_chan_rx = dma_chan;
 
 	return 0;
 }
@@ -190,8 +264,17 @@ static void pci_epf_test_clean_dma_chan(struct pci_epf_test *epf_test)
 	if (!epf_test->dma_supported)
 		return;
 
-	dma_release_channel(epf_test->dma_chan);
-	epf_test->dma_chan = NULL;
+	dma_release_channel(epf_test->dma_chan_tx);
+	if (epf_test->dma_chan_tx == epf_test->dma_chan_rx) {
+		epf_test->dma_chan_tx = NULL;
+		epf_test->dma_chan_rx = NULL;
+		return;
+	}
+
+	dma_release_channel(epf_test->dma_chan_rx);
+	epf_test->dma_chan_rx = NULL;
+
+	return;
 }
 
 static void pci_epf_test_print_rate(const char *ops, u64 size,
@@ -280,8 +363,14 @@ static int pci_epf_test_copy(struct pci_epf_test *epf_test)
 			goto err_map_addr;
 		}
 
+		if (epf_test->dma_private) {
+			dev_err(dev, "Cannot transfer data using DMA\n");
+			ret = -EINVAL;
+			goto err_map_addr;
+		}
+
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size, 0, DMA_MEM_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 	} else {
@@ -363,7 +452,8 @@ static int pci_epf_test_read(struct pci_epf_test *epf_test)
 
 		ktime_get_ts64(&start);
 		ret = pci_epf_test_data_transfer(epf_test, dst_phys_addr,
-						 phys_addr, reg->size);
+						 phys_addr, reg->size,
+						 reg->src_addr, DMA_DEV_TO_MEM);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
@@ -453,8 +543,11 @@ static int pci_epf_test_write(struct pci_epf_test *epf_test)
 		}
 
 		ktime_get_ts64(&start);
+
 		ret = pci_epf_test_data_transfer(epf_test, phys_addr,
-						 src_phys_addr, reg->size);
+						 src_phys_addr, reg->size,
+						 reg->dst_addr,
+						 DMA_MEM_TO_DEV);
 		if (ret)
 			dev_err(dev, "Data transfer failed\n");
 		ktime_get_ts64(&end);
Signature · 1 line
2.35.1
#9 lore raw
In reply to Frank Li

Hello Vinod

Quoted 20 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

Quoted 7 lines

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

This series has been on review for over three months now. It has got several acks, rb and tb tags from me, Manivannan and Kishon (the last patch in the series). Seeing Gustavo hasn't been active for all that time at all and hasn't performed any review for more than a year the probability of getting his attention soon enough is almost zero. Thus could you please give your acks if you are ok with the series content. Due to having several more patchsets dependent on this one, Bjorn has agreed to merge this series in through the PCI tree:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
So the only thing we need is your ack tags.

@Frank. Should there be a new patchset revision could you please add a request to merge the series in to the PCI tree? I am a bit tired repeating the same messages each time the new mailing review lap.)

-Sergey

Quoted 30 lines

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)
Signature · 1 line
2.35.1
#10 lore raw
Quoted 43 lines · Serge Semin

Hello Vinod

Quoted 20 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

Quoted 7 lines

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

This series has been on review for over three months now. It has got several acks, rb and tb tags from me, Manivannan and Kishon (the last patch in the series). Seeing Gustavo hasn't been active for all that time at all and hasn't performed any review for more than a year the probability of getting his attention soon enough is almost zero. Thus could you please give your acks if you are ok with the series content. Due to having several more patchsets dependent on this one, Bjorn has agreed to merge this series in through the PCI tree:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
So the only thing we need is your ack tags.

Quoted 3 lines

@Frank. Should there be a new patchset revision could you please add a request to merge the series in to the PCI tree? I am a bit tired repeating the same messages each time the new mailing review lap.)

The key is to need Vinod to say something

Best regards
Frank Li.

Quoted 33 lines

-Sergey

Quoted 30 lines

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)

--
2.35.1

#11 lore raw
Quoted 45 lines · Zhi Li
Quoted 43 lines · Serge Semin

Hello Vinod

Quoted 20 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

Quoted 7 lines

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

This series has been on review for over three months now. It has got several acks, rb and tb tags from me, Manivannan and Kishon (the last patch in the series). Seeing Gustavo hasn't been active for all that time at all and hasn't performed any review for more than a year the probability of getting his attention soon enough is almost zero. Thus could you please give your acks if you are ok with the series content. Due to having several more patchsets dependent on this one, Bjorn has agreed to merge this series in through the PCI tree:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
So the only thing we need is your ack tags.

Quoted 8 lines
Quoted 3 lines

@Frank. Should there be a new patchset revision could you please add a request to merge the series in to the PCI tree? I am a bit tired repeating the same messages each time the new mailing review lap.)

The key is to need Vinod to say something

Best regards
Frank Li.

@Vinod Kou:
These patches were well reviewed by Serge Semin, Bjorn,
Manivannan Sadhasivam, Kishon Vijay Abraham and tested on 3 platforms.
Pending on your opinion because it touch file under /driver/dma/dw_edma/*

best regards
Frank Li

Quoted 34 lines
Quoted 34 lines

-Sergey

Quoted 30 lines

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)

--
2.35.1

#12 lore raw
Quoted 53 lines · Zhi Li
Quoted 51 lines · Zhi Li
Quoted 43 lines · Serge Semin

Hello Vinod

Quoted 20 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

Quoted 7 lines

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

This series has been on review for over three months now. It has got several acks, rb and tb tags from me, Manivannan and Kishon (the last patch in the series). Seeing Gustavo hasn't been active for all that time at all and hasn't performed any review for more than a year the probability of getting his attention soon enough is almost zero. Thus could you please give your acks if you are ok with the series content. Due to having several more patchsets dependent on this one, Bjorn has agreed to merge this series in through the PCI tree:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
So the only thing we need is your ack tags.

Quoted 3 lines

@Frank. Should there be a new patchset revision could you please add a request to merge the series in to the PCI tree? I am a bit tired repeating the same messages each time the new mailing review lap.)

The key is to need Vinod to say something

Quoted 7 lines
Quoted 2 lines

Best regards
Frank Li.

@Vinod Kou:
These patches were well reviewed by Serge Semin, Bjorn,
Manivannan Sadhasivam, Kishon Vijay Abraham and tested on 3 platforms.
Pending on your opinion because it touch file under /driver/dma/dw_edma/*

@vinod kou:
friendly ping.

Quoted 38 lines

best regards
Frank Li

Quoted 34 lines
Quoted 34 lines

-Sergey

Quoted 30 lines

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)

--
2.35.1

maintainer Applied
#13 lore raw
In reply to Frank Li
Quoted 20 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

Quoted 7 lines

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Applied to dmaengine-next, thanks

Signature · 1 line
~Vinod
#14 lore raw
Quoted 24 lines · Vinod Koul
Quoted 23 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

Quoted 7 lines
Quoted 4 lines

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Applied to dmaengine-next, thanks

Vinoud, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

-Sergey

Quoted 3 lines
Signature · 2 lines
-- 
~Vinod
#15 lore raw
Quoted 31 lines · Serge Semin
Quoted 29 lines · Vinod Koul
Quoted 27 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Quoted 6 lines
Quoted 1 line

Applied to dmaengine-next, thanks

Vinod, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

I asked it several time including in the framework of this thread:
https://lore.kernel.org/dmaengine/20220525092306.wuansog6fe2ika3b@mobilestation/
There are dependencies of my patchsets from this one. Please consider dropping it from your dmaengine-next repo while it's still possible since taking DW eDMA and PCie patches through the PCie repo would be more natural.

-Sergey

Quoted 6 lines

-Sergey

Quoted 3 lines
Signature · 2 lines
-- 
~Vinod
#16 lore raw
Quoted 40 lines · Serge Semin
Quoted 31 lines · Serge Semin
Quoted 29 lines · Vinod Koul
Quoted 27 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Quoted 6 lines
Quoted 1 line

Applied to dmaengine-next, thanks

Vinod, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

Quoted 6 lines

I asked it several time including in the framework of this thread:
https://lore.kernel.org/dmaengine/20220525092306.wuansog6fe2ika3b@mobilestation/
There are dependencies of my patchsets from this one. Please consider dropping it from your dmaengine-next repo while it's still possible since taking DW eDMA and PCie patches through the PCie repo would be more natural.

The only thing we were waiting for was you ack tag...

-Sergey

Quoted 9 lines

-Sergey

Quoted 6 lines

-Sergey

Quoted 3 lines
Signature · 2 lines
-- 
~Vinod
maintainer
#17 lore raw
Quoted 41 lines · Serge Semin
Quoted 39 lines · Serge Semin
Quoted 37 lines · Serge Semin
Quoted 24 lines · Vinod Koul
Quoted 23 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

Quoted 7 lines
Quoted 4 lines

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Applied to dmaengine-next, thanks

Vinod, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

Quoted 8 lines
Quoted 6 lines

I asked it several time including in the framework of this thread:
https://lore.kernel.org/dmaengine/20220525092306.wuansog6fe2ika3b@mobilestation/
There are dependencies of my patchsets from this one. Please consider dropping it from your dmaengine-next repo while it's still possible since taking DW eDMA and PCie patches through the PCie repo would be more natural.

The only thing we were waiting for was you ack tag...

Is there any dependency, since this has many dmaengine patches and one pcie patch which was acked by Kishon, so can go thru dmaengine tree...

I can drop if that suits all...

Signature · 1 line
~Vinod
#18 lore raw
Quoted 49 lines · Vinod Koul
Quoted 48 lines · Serge Semin
Quoted 46 lines · Serge Semin
Quoted 31 lines · Serge Semin
Quoted 29 lines · Vinod Koul
Quoted 27 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Quoted 6 lines
Quoted 1 line

Applied to dmaengine-next, thanks

Vinod, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

I asked it several time including in the framework of this thread:
https://lore.kernel.org/dmaengine/20220525092306.wuansog6fe2ika3b@mobilestation/
There are dependencies of my patchsets from this one. Please consider dropping it from your dmaengine-next repo while it's still possible since taking DW eDMA and PCie patches through the PCie repo would be more natural.

Quoted 5 lines
Quoted 1 line

The only thing we were waiting for was you ack tag...

Is there any dependency, since this has many dmaengine patches and one pcie patch which was acked by Kishon, so can go thru dmaengine tree...

Right. This one is fully suitable for the DMA-engine tree, but there are dependencies of my work from this series. My patchsets in its turn concern both PCIe and DMA-engine parts.

Here is the deal. My work consists of four patchsets:
[PATCH v4 00/18] PCI: dwc: Various fixes and cleanups
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/15] PCI: dwc: Add hw version and dma-ranges support
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/17] PCI: dwc: Add generic resources and Baikal-T1 support
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/24] dmaengine: dw-edma: Add RP/EP local DMA controllers support
https://lore.kernel.org/dmaengine/[email protected]/

The last patchset depends on the Frank series and my DW PCIe patchsets listed above. To cut it shortly here is the dependencies graph:

                PCIe RP/EP            |               DMA engine
                    ^                 |                   ^
                    |                 |                   |
1. Semin: [PATCH v4 00/18] "PCI: dwc: |                   |
   Various fixes and cleanups"        |                   |
                    ^                 |                   |
                    |                 |                   |
2. Semin: [PATCH v3 00/15] "PCI: dwc: |                   |
   Add hw version and dma-ranges      |                   |
   support"                           |                   |
                    ^                 |                   |
                    |                 |                   |
3. Semin: [PATCH v3 00/17] "PCI: dwc: | 4. Li: [PATCH v12 0/8] "Enable
   Add generic resources and Baikal-T1|    designware PCI EP EDMA locally"
   support"                           |                   ^

^ |
| |
+-----------------+-------------------+
|
5. Semin: [PATCH v3 00/24] "dmaengine: dw-edma:
Add RP/EP local DMA controllers support"

As you can see my series (5) depends on the Frank' series (4). My series in its turn depends on the PCI patchsets (3), (2) and (1). So if you get to merge the Frank' patchset into your tree we'll need to merge the rest of the patchsets through your repo too. Seeing the DW eDMA device is implemented as either a separate PCIe device or embedded into the DW PCIe RP/EP controller and there are many PCI-related patches in my work, it would be more suitable to merge all the patches through the PCIe tree. Bjorn already agreed to do that here:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
We only waited for your ackes. BTW should you have some free time please review my series (5) too since it mainly concerns the DW eDMA driver (though Mani, in Cc, has already done it and even performed the testing).

Quoted 2 lines

I can drop if that suits all...

Yes please. Please drop the Frank' series from your repo, give your explicit ack if you are ok with it and let's merge it and the rest of the work through the Bjorn' repo. Patchset (1) has been fully reviewed. Series (2) and (3) need one more iteration to be finished. So I very much hope they will be done in the next few weeks, before the next merge window.

-Sergey

Quoted 3 lines
Signature · 2 lines
-- 
~Vinod
maintainer
#19 lore raw
Quoted 111 lines · Serge Semin
Quoted 49 lines · Vinod Koul
Quoted 48 lines · Serge Semin
Quoted 46 lines · Serge Semin
Quoted 31 lines · Serge Semin
Quoted 29 lines · Vinod Koul
Quoted 27 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Quoted 6 lines
Quoted 1 line

Applied to dmaengine-next, thanks

Vinod, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

I asked it several time including in the framework of this thread:
https://lore.kernel.org/dmaengine/20220525092306.wuansog6fe2ika3b@mobilestation/
There are dependencies of my patchsets from this one. Please consider dropping it from your dmaengine-next repo while it's still possible since taking DW eDMA and PCie patches through the PCie repo would be more natural.

Quoted 5 lines
Quoted 1 line

The only thing we were waiting for was you ack tag...

Is there any dependency, since this has many dmaengine patches and one pcie patch which was acked by Kishon, so can go thru dmaengine tree...

Right. This one is fully suitable for the DMA-engine tree, but there are dependencies of my work from this series. My patchsets in its turn concern both PCIe and DMA-engine parts.

Here is the deal. My work consists of four patchsets:
[PATCH v4 00/18] PCI: dwc: Various fixes and cleanups
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/15] PCI: dwc: Add hw version and dma-ranges support
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/17] PCI: dwc: Add generic resources and Baikal-T1 support
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/24] dmaengine: dw-edma: Add RP/EP local DMA controllers support
https://lore.kernel.org/dmaengine/[email protected]/

The last patchset depends on the Frank series and my DW PCIe patchsets listed above. To cut it shortly here is the dependencies graph:

                PCIe RP/EP            |               DMA engine
                    ^                 |                   ^
                    |                 |                   |
1. Semin: [PATCH v4 00/18] "PCI: dwc: |                   |
   Various fixes and cleanups"        |                   |
                    ^                 |                   |
                    |                 |                   |
2. Semin: [PATCH v3 00/15] "PCI: dwc: |                   |
   Add hw version and dma-ranges      |                   |
   support"                           |                   |
                    ^                 |                   |
                    |                 |                   |
3. Semin: [PATCH v3 00/17] "PCI: dwc: | 4. Li: [PATCH v12 0/8] "Enable
   Add generic resources and Baikal-T1|    designware PCI EP EDMA locally"
   support"                           |                   ^

^ |
| |
+-----------------+-------------------+
|
5. Semin: [PATCH v3 00/24] "dmaengine: dw-edma:
Add RP/EP local DMA controllers support"

As you can see my series (5) depends on the Frank' series (4). My series in its turn depends on the PCI patchsets (3), (2) and (1). So if you get to merge the Frank' patchset into your tree we'll need to merge the rest of the patchsets through your repo too. Seeing the DW eDMA device is implemented as either a separate PCIe device or embedded into the DW PCIe RP/EP controller and there are many PCI-related patches in my work, it would be more suitable to merge all the patches through the PCIe tree. Bjorn already agreed to do that here:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
We only waited for your ackes. BTW should you have some free time please review my series (5) too since it mainly concerns the DW eDMA driver (though Mani, in Cc, has already done it and even performed the testing).

Quoted 1 line
Quoted 8 lines
Quoted 1 line

I can drop if that suits all...

Yes please. Please drop the Frank' series from your repo, give your explicit ack if you are ok with it and let's merge it and the rest of the work through the Bjorn' repo. Patchset (1) has been fully reviewed. Series (2) and (3) need one more iteration to be finished. So I very much hope they will be done in the next few weeks, before the next merge window.

Ok dropped now

Signature · 1 line
~Vinod
#20 lore raw
Quoted 122 lines · Vinod Koul
Quoted 111 lines · Serge Semin
Quoted 49 lines · Vinod Koul
Quoted 48 lines · Serge Semin
Quoted 46 lines · Serge Semin
Quoted 31 lines · Serge Semin
Quoted 29 lines · Vinod Koul
Quoted 27 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Quoted 6 lines
Quoted 1 line

Applied to dmaengine-next, thanks

Vinod, this was supposed to be merged in through PCIe repo.( I asked many times of that. Bjorn also agreed to merge it in. Could drop it from yout repo?

I asked it several time including in the framework of this thread:
https://lore.kernel.org/dmaengine/20220525092306.wuansog6fe2ika3b@mobilestation/
There are dependencies of my patchsets from this one. Please consider dropping it from your dmaengine-next repo while it's still possible since taking DW eDMA and PCie patches through the PCie repo would be more natural.

Quoted 5 lines
Quoted 1 line

The only thing we were waiting for was you ack tag...

Is there any dependency, since this has many dmaengine patches and one pcie patch which was acked by Kishon, so can go thru dmaengine tree...

Right. This one is fully suitable for the DMA-engine tree, but there are dependencies of my work from this series. My patchsets in its turn concern both PCIe and DMA-engine parts.

Here is the deal. My work consists of four patchsets:
[PATCH v4 00/18] PCI: dwc: Various fixes and cleanups
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/15] PCI: dwc: Add hw version and dma-ranges support
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/17] PCI: dwc: Add generic resources and Baikal-T1 support
https://lore.kernel.org/linux-pci/[email protected]/
[PATCH v3 00/24] dmaengine: dw-edma: Add RP/EP local DMA controllers support
https://lore.kernel.org/dmaengine/[email protected]/

The last patchset depends on the Frank series and my DW PCIe patchsets listed above. To cut it shortly here is the dependencies graph:

                PCIe RP/EP            |               DMA engine
                    ^                 |                   ^
                    |                 |                   |
1. Semin: [PATCH v4 00/18] "PCI: dwc: |                   |
   Various fixes and cleanups"        |                   |
                    ^                 |                   |
                    |                 |                   |
2. Semin: [PATCH v3 00/15] "PCI: dwc: |                   |
   Add hw version and dma-ranges      |                   |
   support"                           |                   |
                    ^                 |                   |
                    |                 |                   |
3. Semin: [PATCH v3 00/17] "PCI: dwc: | 4. Li: [PATCH v12 0/8] "Enable
   Add generic resources and Baikal-T1|    designware PCI EP EDMA locally"
   support"                           |                   ^

^ |
| |
+-----------------+-------------------+
|
5. Semin: [PATCH v3 00/24] "dmaengine: dw-edma:
Add RP/EP local DMA controllers support"

As you can see my series (5) depends on the Frank' series (4). My series in its turn depends on the PCI patchsets (3), (2) and (1). So if you get to merge the Frank' patchset into your tree we'll need to merge the rest of the patchsets through your repo too. Seeing the DW eDMA device is implemented as either a separate PCIe device or embedded into the DW PCIe RP/EP controller and there are many PCI-related patches in my work, it would be more suitable to merge all the patches through the PCIe tree. Bjorn already agreed to do that here:
https://lore.kernel.org/linux-pci/20220524155201.GA247821@bhelgaas/
We only waited for your ackes. BTW should you have some free time please review my series (5) too since it mainly concerns the DW eDMA driver (though Mani, in Cc, has already done it and even performed the testing).

Quoted 1 line
Quoted 8 lines
Quoted 1 line

I can drop if that suits all...

Yes please. Please drop the Frank' series from your repo, give your explicit ack if you are ok with it and let's merge it and the rest of the work through the Bjorn' repo. Patchset (1) has been fully reviewed. Series (2) and (3) need one more iteration to be finished. So I very much hope they will be done in the next few weeks, before the next merge window.

Quoted 1 line

Ok dropped now

Great! Thank you very much. Bjord has just merged in the series through his repo.

-Sergey

Quoted 3 lines
Signature · 2 lines
-- 
~Vinod
maintainer Acked-by on the v12 series
#21 lore raw
In reply to Frank Li
Quoted 20 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

Quoted 7 lines

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Signature · 1 line
~Vinod
#22 lore raw
In reply to Frank Li
Quoted 43 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

Quoted 10 lines
 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)

Applied with Vinod's ack to pci/edma for v5.20, thanks!

Check
https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/log/?h=pci/edma
(head 7871514c9cff ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")).

If you post things that need to be applied on top of that branch, please mention that in the cover letter.

I don't guarantee the immutability of the branch because sometimes I fix typos or similar errors before the merge window.

Bjorn

#23 lore raw
Quoted 56 lines · Bjorn Helgaas
Quoted 43 lines · Frank Li

Default Designware EDMA just probe remotely at host side. This patch allow EDMA driver can probe at EP side.

1. Clean up patch
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Change rg_region to reg_base in struct
dmaengine: dw-edma: rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct

2. Enhance EDMA driver to allow prode eDMA at EP side
dmaengine: dw-edma: Add support for chip specific flags
dmaengine: dw-edma: Add DW_EDMA_CHIP_32BIT_DBI for chip specific
flags (this patch removed at v11 because dma tree already have fixed patch)

3. Bugs fix at EDMA driver when probe eDMA at EP side
dmaengine: dw-edma: Fix programming the source & dest addresses for
ep
dmaengine: dw-edma: Don't rely on the deprecated "direction" member

4. change pci-epf-test to use EDMA driver to transfer data.
PCI: endpoint: Add embedded DMA controller test

5. Using imx8dxl to do test, but some EP functions still have not upstream yet. So below patch show how probe eDMA driver at EP controller driver.
https://lore.kernel.org/linux-pci/20220309120149.GB134091@thinkpad/T/#m979eb506c73ab3cfca2e7a43635ecdaec18d8097

Frank Li (6):
dmaengine: dw-edma: Remove unused field irq in struct dw_edma_chip
dmaengine: dw-edma: Detach the private data and chip info structures
dmaengine: dw-edma: Change rg_region to reg_base in struct
dw_edma_chip
dmaengine: dw-edma: Rename wr(rd)_ch_cnt to ll_wr(rd)_cnt in struct
dw_edma_chip
dmaengine: dw-edma: Add support for chip specific flags
PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities

Serge Semin (2):
dmaengine: dw-edma: Drop dma_slave_config.direction field usage
dmaengine: dw-edma: Fix eDMA Rd/Wr-channels and DMA-direction
semantics

Quoted 10 lines
 drivers/dma/dw-edma/dw-edma-core.c            | 141 +++++++++++-------
 drivers/dma/dw-edma/dw-edma-core.h            |  31 +---
 drivers/dma/dw-edma/dw-edma-pcie.c            |  83 +++++------
 drivers/dma/dw-edma/dw-edma-v0-core.c         |  41 ++---
 drivers/dma/dw-edma/dw-edma-v0-core.h         |   4 +-
 drivers/dma/dw-edma/dw-edma-v0-debugfs.c      |  18 +--
 drivers/dma/dw-edma/dw-edma-v0-debugfs.h      |   8 +-
 drivers/pci/endpoint/functions/pci-epf-test.c | 112 ++++++++++++--
 include/linux/dma/edma.h                      |  59 +++++++-
 9 files changed, 317 insertions(+), 180 deletions(-)
Quoted 6 lines

Applied with Vinod's ack to pci/edma for v5.20, thanks!

Check
https://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci.git/log/?h=pci/edma
(head 7871514c9cff ("PCI: endpoint: Enable DMA tests for endpoints with DMA capabilities")).

Great! Just what we needed.

Quoted 3 lines

If you post things that need to be applied on top of that branch, please mention that in the cover letter.

Ok. I'll mention that in the cover letters of my patchsets.

I've already got several R-b/T-b tags in the series:
https://lore.kernel.org/linux-pci/[email protected]/
Could you also have a look at it? If no objection we can either merge it in right away into the pci/edma branch or wait for a little while for a few more rc-cycles until I get to fix all the comments posted for the dependant patchsets.

Quoted 3 lines

I don't guarantee the immutability of the branch because sometimes I fix typos or similar errors before the merge window.

Got it.

-Sergey

Quoted 2 lines

Bjorn