Skip to contentSkip to conversation

staging/iio: Clean up AD7746 CDC driver and move from staging.

PATCH Superseded Jonathan Cameron 3 participants 21 messages Apr 18, 2022 – Apr 28, 2022

Subsystems (4)

v1 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Jonathan Cameron

author maintainer
#0 lore raw

cover staging/iio: Clean up AD7746 CDC driver and move from staging.

From: Jonathan Cameron <[email protected]>

This started out as an experiment with Vincent Whitchurch's roadtest testing framework [1] and that worked well so I carried on cleaning up the driver.

Mostly this is standard tidy up, move to new interfaces, then move the driver out of staging, but there are a few other things in here.

1) Precision improvement for IIO_VAL_FRACTIONAL_LOG2.
The ad7746 is a 24 bit sensor and this highlighted that 9 decimal places wasn't enough to keep the error introduced by
_raw * _scale from growing too large over the whole range (I couldn't write a sensible test for it). So I've proposed increasing the precision of the calculation used to provide the sysfs attributes with this value type and printing a few more decimal places (12).
2) _inputoffset ABI addition. This driver had an odd use of _offset for the case of differential channels that applied the offset to both of the differential pair (hence usespace shouldn't not apply it when converting to the base units. That isn't inline with the existing documentation for _offset and it wasn't clear to me that it made sense at all. To avoid confusion I've added this new ABI (_inputoffset) for t
3) roadtest file - note this is not a complete test set for the driver and mainly focused on the main channel reads and places I thought I might have broken things whilst working on the driver.

My conclusion on roadtest - Very useful indeed. I'd encourage others to consider developing some basic sanity tests for drivers they are working on. Hopefully my python code isn't too hideous to understand at least! Vincent, it might be worth thinking about some generic code to handle the 'variants' on correct ABI like I introduce here because I switched from a shared by type scale to an individual one per channel for the voltages. Both were ABI compliant so that sort of change is fine most of the time though we have to be careful with it.

All comments welcome. Note there may be changes that make more sense to do after moving this out of staging as long as there are no ABI changes involved etc. Feel free to highlight those sorts of changes as well as anything more significant.

[1] https://lore.kernel.org/all/[email protected]/

Jonathan Cameron (17):
iio: core: Increase precision of IIO_VAL_FRACTIONAL_LOG2
iio: ABI: Fix wrong format of differential capacitance channel ABI.
staging: iio: cdc: ad7746: Use explicit be24 handling.
staging: iio: cdc: ad7746: Push handling of supply voltage scale to
userspace.
staging: iio: cdc: ad7746: Use local buffer for multi byte reads.
staging: iio: cdc: ad7746: Factor out ad7746_read_channel()
staging: iio: cdc: ad7764: Push locking down into case statements in
read/write_raw
staging: iio: cdc: ad7746: Break up use of chan->address and use
FIELD_PREP etc
staging: iio: cdc: ad7746: Drop usused i2c_set_clientdata()
staging: iio: cdc: ad7746: Use _raw and _scale for temperature
channels.
iio: core: Introduce _inputoffset for differential channels
staging: iio: cdc: ad7746: Switch from _offset to _inputoffset for
differential channels.
staging: iio: cdc: ad7746: Use read_avail() rather than opencoding.
staging: iio: ad7746: White space cleanup
iio: cdc: ad7746: Add device specific ABI documentation.
iio: cdc: ad7746: Move driver out of staging.
RFC: iio: cdc: ad7746: Add roadtest

 Documentation/ABI/testing/sysfs-bus-iio       |  15 +-
 .../ABI/testing/sysfs-bus-iio-cdc-ad7746      |  11 +
 drivers/iio/cdc/Kconfig                       |  10 +
 drivers/iio/cdc/Makefile                      |   1 +
 drivers/iio/cdc/ad7746.c                      | 818 ++++++++++++++++++
 drivers/iio/industrialio-core.c               |  24 +-
 drivers/staging/iio/cdc/ad7746.c              | 767 ----------------
 include/linux/iio/types.h                     |   1 +
 .../roadtest/tests/iio/cdc/__init__.py        |   0
 .../roadtest/roadtest/tests/iio/cdc/config    |   1 +
 .../roadtest/tests/iio/cdc/test_ad7746.py     | 323 +++++++
 11 files changed, 1195 insertions(+), 776 deletions(-)
 create mode 100644 Documentation/ABI/testing/sysfs-bus-iio-cdc-ad7746
 create mode 100644 drivers/iio/cdc/ad7746.c
 delete mode 100644 drivers/staging/iio/cdc/ad7746.c
 create mode 100644 tools/testing/roadtest/roadtest/tests/iio/cdc/__init__.py
 create mode 100644 tools/testing/roadtest/roadtest/tests/iio/cdc/config
 create mode 100644 tools/testing/roadtest/roadtest/tests/iio/cdc/test_ad7746.py
Signature · 1 line
2.35.3
author maintainer
#1 lore raw

PATCH 1/17 iio: core: Increase precision of IIO_VAL_FRACTIONAL_LOG2

From: Jonathan Cameron <[email protected]>

With some high resolution sensors such as the ad7746 the build up of error when multiplying the _raw and _scale values together can be significant. Reduce this affect by providing additional resolution in both calculation and formatting of result.

---
 drivers/iio/industrialio-core.c | 23 +++++++++++++++--------
 1 file changed, 15 insertions(+), 8 deletions(-)
drivers/iio/industrialio-core.c +15 -8
index 2f48e9a97274..d831835770da 100644
@@ -683,14 +683,21 @@ static ssize_t __iio_format_value(char *buf, size_t offset, unsigned int type,
 		else
 			return sysfs_emit_at(buf, offset, "%d.%09u", tmp0,
 					     abs(tmp1));
-	case IIO_VAL_FRACTIONAL_LOG2:
-		tmp2 = shift_right((s64)vals[0] * 1000000000LL, vals[1]);
-		tmp0 = (int)div_s64_rem(tmp2, 1000000000LL, &tmp1);
-		if (tmp0 == 0 && tmp2 < 0)
-			return sysfs_emit_at(buf, offset, "-0.%09u", abs(tmp1));
-		else
-			return sysfs_emit_at(buf, offset, "%d.%09u", tmp0,
-					     abs(tmp1));
+	case IIO_VAL_FRACTIONAL_LOG2: {
+		u64 t1, t2;
+		int integer;
+		bool neg = vals[0] < 0;
+
+		t1 = shift_right((u64)abs(vals[0]) * 1000000000000ULL, vals[1]);
+		integer = (int)div64_u64_rem(t1, 1000000000000ULL, &t2);
+		if (integer == 0 && neg)
+			return sysfs_emit_at(buf, offset, "-0.%012llu", abs(t2));
+		if (neg)
+			integer *= -1;
+		return sysfs_emit_at(buf, offset, "%d.%012llu", integer,
+				     abs(t2));
+		}
+	}
 	case IIO_VAL_INT_MULTIPLE:
 	{
 		int i;
Signature · 1 line
2.35.3
#2 lore raw

Re: [PATCH 01/17] iio: core: Increase precision of IIO_VAL_FRACTIONAL_LOG2

Hi!

Quoted 25 lines

From: Jonathan Cameron <[email protected]>

With some high resolution sensors such as the ad7746 the build up of error when multiplying the _raw and _scale values together can be significant. Reduce this affect by providing additional resolution in both calculation and formatting of result.

---
 drivers/iio/industrialio-core.c | 23 +++++++++++++++--------
 1 file changed, 15 insertions(+), 8 deletions(-)
drivers/iio/industrialio-core.c +0 -4
index 2f48e9a97274..d831835770da 100644
@@ -683,14 +683,21 @@ static ssize_t __iio_format_value(char *buf, size_t offset, unsigned int type,
 		else
 			return sysfs_emit_at(buf, offset, "%d.%09u", tmp0,
 					     abs(tmp1));
-	case IIO_VAL_FRACTIONAL_LOG2:
-		tmp2 = shift_right((s64)vals[0] * 1000000000LL, vals[1]);
-		tmp0 = (int)div_s64_rem(tmp2, 1000000000LL, &tmp1);
-		if (tmp0 == 0 && tmp2 < 0)

drivers/iio/industrialio-core.c static ssize_t __iio_format_value(char *buf, size_t offset, unsigned int type, · line 691

Quoted 10 lines
drivers/iio/industrialio-core.c +6 -4
-			return sysfs_emit_at(buf, offset, "-0.%09u", abs(tmp1));
-		else
-			return sysfs_emit_at(buf, offset, "%d.%09u", tmp0,
-					     abs(tmp1));
+	case IIO_VAL_FRACTIONAL_LOG2: {
+		u64 t1, t2;
+		int integer;
+		bool neg = vals[0] < 0;
+
+		t1 = shift_right((u64)abs(vals[0]) * 1000000000000ULL, vals[1]);

While the multiplication is safe if val[0] is 24 bits or less, I wonder if that's OK for *all* the existing stuff? I would have guessed that something somewhere needs more bits than that? Did you consider the rescaler? And if everything currently really does fit in 24 bits, do we really want to make it difficult to add something beyond 24 bits later on?

Cheers,
Peter

Quoted 15 lines
drivers/iio/industrialio-core.c +9 -0
+		integer = (int)div64_u64_rem(t1, 1000000000000ULL, &t2);
+		if (integer == 0 && neg)
+			return sysfs_emit_at(buf, offset, "-0.%012llu", abs(t2));
+		if (neg)
+			integer *= -1;
+		return sysfs_emit_at(buf, offset, "%d.%012llu", integer,
+				     abs(t2));
+		}
+	}
 	case IIO_VAL_INT_MULTIPLE:
 	{
 		int i;
Signature · 1 line
2.35.3
author maintainer
#3 lore raw

Re: [PATCH 01/17] iio: core: Increase precision of IIO_VAL_FRACTIONAL_LOG2

Quoted 36 lines · On Tue, 26 Apr 2022 14:00:49 +0200 Peter Rosin <[email protected]> wrote:

Hi!

Quoted 34 lines

From: Jonathan Cameron <[email protected]>

With some high resolution sensors such as the ad7746 the build up of error when multiplying the _raw and _scale values together can be significant. Reduce this affect by providing additional resolution in both calculation and formatting of result.

---
 drivers/iio/industrialio-core.c | 23 +++++++++++++++--------
 1 file changed, 15 insertions(+), 8 deletions(-)
drivers/iio/industrialio-core.c +5 -8
index 2f48e9a97274..d831835770da 100644
@@ -683,14 +683,21 @@ static ssize_t __iio_format_value(char *buf, size_t offset, unsigned int type,
 		else
 			return sysfs_emit_at(buf, offset, "%d.%09u", tmp0,
 					     abs(tmp1));
-	case IIO_VAL_FRACTIONAL_LOG2:
-		tmp2 = shift_right((s64)vals[0] * 1000000000LL, vals[1]);
-		tmp0 = (int)div_s64_rem(tmp2, 1000000000LL, &tmp1);
-		if (tmp0 == 0 && tmp2 < 0)
-			return sysfs_emit_at(buf, offset, "-0.%09u", abs(tmp1));
-		else
-			return sysfs_emit_at(buf, offset, "%d.%09u", tmp0,
-					     abs(tmp1));
+	case IIO_VAL_FRACTIONAL_LOG2: {
+		u64 t1, t2;
+		int integer;
+		bool neg = vals[0] < 0;
+
Quoted 8 lines

drivers/iio/industrialio-core.c static ssize_t __iio_format_value(char *buf, size_t offset, unsigned int type, · line 691

Quoted 1 line
drivers/iio/industrialio-core.c +1 -0
+		t1 = shift_right((u64)abs(vals[0]) * 1000000000000ULL, vals[1]);  

While the multiplication is safe if val[0] is 24 bits or less, I wonder if that's OK for *all* the existing stuff? I would have guessed that something somewhere needs more bits than that? Did you consider the rescaler? And if everything currently really does fit in 24 bits, do we really want to make it difficult to add something beyond 24 bits later on?

Good point. Perhaps we can do something a bit nefarious and check that val[0] is sufficiently small and if not fallback to lower precision as we had before? Or if adventurous adjust the precision automatically so we can get as many digits (at least 9) as can be computed without overflow... For now, I think 2 steps is enough though.

Jonathan

Quoted 20 lines

Cheers,
Peter

Quoted 15 lines
drivers/iio/industrialio-core.c +9 -0
+		integer = (int)div64_u64_rem(t1, 1000000000000ULL, &t2);
+		if (integer == 0 && neg)
+			return sysfs_emit_at(buf, offset, "-0.%012llu", abs(t2));
+		if (neg)
+			integer *= -1;
+		return sysfs_emit_at(buf, offset, "%d.%012llu", integer,
+				     abs(t2));
+		}
+	}
 	case IIO_VAL_INT_MULTIPLE:
 	{
 		int i;
Signature · 1 line
2.35.3
author maintainer
#4 lore raw

PATCH 2/17 iio: ABI: Fix wrong format of differential capacitance channel ABI.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

in_ only occurs once in these attributes.

---
 Documentation/ABI/testing/sysfs-bus-iio | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
Documentation/ABI/testing/sysfs-bus-iio +1 -1
index d4ccc68fdcf0..b19ff517e5d6 100644
@@ -188,7 +188,7 @@ Description:
 		Raw capacitance measurement from channel Y. Units after
 		application of scale and offset are nanofarads.
 
-What:		/sys/.../iio:deviceX/in_capacitanceY-in_capacitanceZ_raw
+What:		/sys/.../iio:deviceX/in_capacitanceY-capacitanceZ_raw
 KernelVersion:	3.2
 Contact:	[email protected]
 Description:
Signature · 1 line
2.35.3
author maintainer
#5 lore raw

PATCH 3/17 staging: iio: cdc: ad7746: Use explicit be24 handling.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Change from fiddly local implementation of be24 to cpu endian conversion by reading into a 3 byte buffer and using get_unaligned_be24()

---
 drivers/staging/iio/cdc/ad7746.c | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)
drivers/staging/iio/cdc/ad7746.c +3 -6
index 71c709771676..1f510610ed32 100644
@@ -95,10 +95,7 @@ struct ad7746_chip_info {
 	u8	capdac[2][2];
 	s8	capdac_set;
 
-	union {
-		__be32 d32;
-		u8 d8[4];
-	} data ____cacheline_aligned;
+	u8 data[3] ____cacheline_aligned;
 };
 
 enum ad7746_chan {
@@ -547,12 +544,12 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 
 		ret = i2c_smbus_read_i2c_block_data(chip->client,
 						    chan->address >> 8, 3,
-						    &chip->data.d8[1]);
+						    chip->data);
 
 		if (ret < 0)
 			goto out;
 
-		*val = (be32_to_cpu(chip->data.d32) & 0xFFFFFF) - 0x800000;
+		*val = get_unaligned_be24(chip->data) - 0x800000;
 
 		switch (chan->type) {
 		case IIO_TEMP:
Signature · 1 line
2.35.3
#6 lore raw

Re: [PATCH 03/17] staging: iio: cdc: ad7746: Use explicit be24 handling.

Quoted 28 lines · Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Change from fiddly local implementation of be24 to cpu endian conversion by reading into a 3 byte buffer and using get_unaligned_be24()

---
 drivers/staging/iio/cdc/ad7746.c | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)
drivers/staging/iio/cdc/ad7746.c +1 -4
index 71c709771676..1f510610ed32 100644
@@ -95,10 +95,7 @@ struct ad7746_chip_info {
        u8      capdac[2][2];
        s8      capdac_set;
 
-       union {
-               __be32 d32;
-               u8 d8[4];
-       } data ____cacheline_aligned;
+       u8 data[3] ____cacheline_aligned;
 };
 
 enum ad7746_chan {

drivers/staging/iio/cdc/ad7746.c static int ad7746_read_raw(struct iio_dev *indio_dev, · line 546

Quoted 3 lines
drivers/staging/iio/cdc/ad7746.c +0 -0
@@ -547,12 +544,12 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 
                ret = i2c_smbus_read_i2c_block_data(chip->client,
                                                    chan->address >> 8, 3,

At the same time it makes now sense to use sizeof() here.

Quoted 14 lines
drivers/staging/iio/cdc/ad7746.c +2 -3
-                                                   &chip->data.d8[1]);
+                                                   chip->data);
 
                if (ret < 0)
                        goto out;
 
-               *val = (be32_to_cpu(chip->data.d32) & 0xFFFFFF) - 0x800000;
+               *val = get_unaligned_be24(chip->data) - 0x800000;
 
                switch (chan->type) {
                case IIO_TEMP:
--

2.35.3

Signature · 2 lines
With Best Regards,
Andy Shevchenko
author maintainer
#7 lore raw

PATCH 4/17 staging: iio: cdc: ad7746: Push handling of supply voltage scale to userspace.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

The supply voltage is attenuated by 6 before being fed to the ADC. Handle this explcitly rather than premultiplying the _raw value by 6.

---
 drivers/staging/iio/cdc/ad7746.c | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)
drivers/staging/iio/cdc/ad7746.c +6 -10
index 1f510610ed32..1379caf88b83 100644
@@ -114,9 +114,8 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.type = IIO_VOLTAGE,
 		.indexed = 1,
 		.channel = 0,
-		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
-		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |
-			BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = AD7746_REG_VT_DATA_HIGH << 8 |
 			AD7746_VTSETUP_VTMD_EXT_VIN,
 	},
@@ -125,9 +124,8 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.indexed = 1,
 		.channel = 1,
 		.extend_name = "supply",
-		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
-		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |
-			BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = AD7746_REG_VT_DATA_HIGH << 8 |
 			AD7746_VTSETUP_VTMD_VDD_MON,
 	},
@@ -559,10 +557,6 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 			 */
 			*val = (*val * 125) / 256;
 			break;
-		case IIO_VOLTAGE:
-			if (chan->channel == 1) /* supply_raw*/
-				*val = *val * 6;
-			break;
 		default:
 			break;
 		}
@@ -617,6 +611,8 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 		case IIO_VOLTAGE:
 			/* 1170mV / 2^23 */
 			*val = 1170;
+			if (chan->channel == 1)
+				*val *= 6;
 			*val2 = 23;
 			ret = IIO_VAL_FRACTIONAL_LOG2;
 			break;
Signature · 1 line
2.35.3
author maintainer
#8 lore raw

PATCH 5/17 staging: iio: cdc: ad7746: Use local buffer for multi byte reads.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

I2C does not require DMA safe buffers so there is no need to ensure the buffers are in their own cacheline. Hence simplify things by using a local variable instead of embedding the buffer in the chip info structure.

---
 drivers/staging/iio/cdc/ad7746.c | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)
drivers/staging/iio/cdc/ad7746.c +3 -4
index 1379caf88b83..e4b882586891 100644
@@ -94,8 +94,6 @@ struct ad7746_chip_info {
 	u8	vt_setup;
 	u8	capdac[2][2];
 	s8	capdac_set;
-
-	u8 data[3] ____cacheline_aligned;
 };
 
 enum ad7746_chan {
@@ -520,6 +518,7 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 	struct ad7746_chip_info *chip = iio_priv(indio_dev);
 	int ret, delay, idx;
 	u8 regval, reg;
+	u8 data[3];
 
 	mutex_lock(&chip->lock);
 
@@ -542,12 +541,12 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 
 		ret = i2c_smbus_read_i2c_block_data(chip->client,
 						    chan->address >> 8, 3,
-						    chip->data);
+						    data);
 
 		if (ret < 0)
 			goto out;
 
-		*val = get_unaligned_be24(chip->data) - 0x800000;
+		*val = get_unaligned_be24(data) - 0x800000;
 
 		switch (chan->type) {
 		case IIO_TEMP:
Signature · 1 line
2.35.3
author maintainer
#9 lore raw

PATCH 6/17 staging: iio: cdc: ad7746: Factor out ad7746_read_channel()

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Reduce deep indenting and simplify the locking cleanup that follows.

---
 drivers/staging/iio/cdc/ad7746.c | 79 ++++++++++++++++----------------
 1 file changed, 40 insertions(+), 39 deletions(-)
drivers/staging/iio/cdc/ad7746.c +40 -39
index e4b882586891..6b9530bd12cc 100644
@@ -500,14 +500,47 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 		default:
 			ret = -EINVAL;
 		}
+static int ad7746_read_channel(struct iio_dev *indio_dev,
+			       struct iio_chan_spec const *chan,
+			       int *val)
+{
+	struct ad7746_chip_info *chip = iio_priv(indio_dev);
+	int ret, delay;
+	u8 data[3];
+	u8 regval;
+
+	ret = ad7746_select_channel(indio_dev, chan);
+	if (ret < 0)
+		return ret;
+	delay = ret;
+
+	regval = chip->config | AD7746_CONF_MODE_SINGLE_CONV;
+	ret = i2c_smbus_write_byte_data(chip->client, AD7746_REG_CFG, regval);
+	if (ret < 0)
+		return ret;
+
+	msleep(delay);
+	/* Now read the actual register */
+	ret = i2c_smbus_read_i2c_block_data(chip->client,  chan->address >> 8,
+					    3, data);
+	if (ret < 0)
+		return ret;
+
+	*val = get_unaligned_be24(data) - 0x800000;
+
+	switch (chan->type) {
+	case IIO_TEMP:
+		/*
+		 * temperature in milli degrees Celsius
+		 * T = ((*val / 2048) - 4096) * 1000
+		 */
+		*val = (*val  * 125) / 256;
 		break;
 	default:
-		ret = -EINVAL;
+		break;
 	}
 
-out:
-	mutex_unlock(&chip->lock);
-	return ret;
+	return 0;
 }
 
 static int ad7746_read_raw(struct iio_dev *indio_dev,
@@ -516,49 +549,17 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 			   long mask)
 {
 	struct ad7746_chip_info *chip = iio_priv(indio_dev);
-	int ret, delay, idx;
-	u8 regval, reg;
-	u8 data[3];
+	int ret, idx;
+	u8 reg;
 
 	mutex_lock(&chip->lock);
 
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
 	case IIO_CHAN_INFO_PROCESSED:
-		ret = ad7746_select_channel(indio_dev, chan);
+		ret = ad7746_read_channel(indio_dev, chan, val);
 		if (ret < 0)
 			goto out;
-		delay = ret;
-
-		regval = chip->config | AD7746_CONF_MODE_SINGLE_CONV;
-		ret = i2c_smbus_write_byte_data(chip->client, AD7746_REG_CFG,
-						regval);
-		if (ret < 0)
-			goto out;
-
-		msleep(delay);
-		/* Now read the actual register */
-
-		ret = i2c_smbus_read_i2c_block_data(chip->client,
-						    chan->address >> 8, 3,
-						    data);
-
-		if (ret < 0)
-			goto out;
-
-		*val = get_unaligned_be24(data) - 0x800000;
-
-		switch (chan->type) {
-		case IIO_TEMP:
-			/*
-			 * temperature in milli degrees Celsius
-			 * T = ((*val / 2048) - 4096) * 1000
-			 */
-			*val = (*val * 125) / 256;
-			break;
-		default:
-			break;
-		}
 
 		ret = IIO_VAL_INT;
 		break;
Signature · 1 line
2.35.3
author maintainer
#10 lore raw

PATCH 7/17 staging: iio: cdc: ad7764: Push locking down into case statements in read/write_raw

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Not all paths require any locking at all. So to simplify the removal of such locking push the locks down into the individual case statements.

---
 drivers/staging/iio/cdc/ad7746.c | 125 ++++++++++++++-----------------
 1 file changed, 58 insertions(+), 67 deletions(-)
drivers/staging/iio/cdc/ad7746.c +58 -67
index 6b9530bd12cc..34e19677d1fe 100644
@@ -418,14 +418,10 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 	struct ad7746_chip_info *chip = iio_priv(indio_dev);
 	int ret, reg;
 
-	mutex_lock(&chip->lock);
-
 	switch (mask) {
 	case IIO_CHAN_INFO_CALIBSCALE:
-		if (val != 1) {
-			ret = -EINVAL;
-			goto out;
-		}
+		if (val != 1)
+			return -EINVAL;
 
 		val = (val2 * 1024) / 15625;
 
@@ -437,33 +433,31 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 			reg = AD7746_REG_VOLT_GAINH;
 			break;
 		default:
-			ret = -EINVAL;
-			goto out;
+			return -EINVAL;
 		}
 
+		mutex_lock(&chip->lock);
 		ret = i2c_smbus_write_word_swapped(chip->client, reg, val);
+		mutex_unlock(&chip->lock);
 		if (ret < 0)
-			goto out;
+			return ret;
 
-		ret = 0;
-		break;
+		return 0;
 	case IIO_CHAN_INFO_CALIBBIAS:
-		if (val < 0 || val > 0xFFFF) {
-			ret = -EINVAL;
-			goto out;
-		}
+		if (val < 0 || val > 0xFFFF)
+			return -EINVAL;
+
+		mutex_lock(&chip->lock);
 		ret = i2c_smbus_write_word_swapped(chip->client,
 						   AD7746_REG_CAP_OFFH, val);
+		mutex_unlock(&chip->lock);
 		if (ret < 0)
-			goto out;
+			return ret;
 
-		ret = 0;
-		break;
+		return 0;
 	case IIO_CHAN_INFO_OFFSET:
-		if (val < 0 || val > 43008000) { /* 21pF */
-			ret = -EINVAL;
-			goto out;
-		}
+		if (val < 0 || val > 43008000) /* 21pF */
+			return -EINVAL;
 
 		/*
 		 * CAPDAC Scale = 21pF_typ / 127
@@ -472,34 +466,43 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 		 */
 
 		val /= 338646;
-
+		mutex_lock(&chip->lock);
 		chip->capdac[chan->channel][chan->differential] = val > 0 ?
 			AD7746_CAPDAC_DACP(val) | AD7746_CAPDAC_DACEN : 0;
 
 		ret = ad7746_set_capdac(chip, chan->channel);
-		if (ret < 0)
-			goto out;
+		if (ret < 0) {
+			mutex_unlock(&chip->lock);
+			return ret;
+		}
 
 		chip->capdac_set = chan->channel;
+		mutex_unlock(&chip->lock);
 
-		ret = 0;
-		break;
+		return 0;
 	case IIO_CHAN_INFO_SAMP_FREQ:
-		if (val2) {
-			ret = -EINVAL;
-			goto out;
-		}
+		if (val2)
+			return -EINVAL;
 
 		switch (chan->type) {
 		case IIO_CAPACITANCE:
+			mutex_lock(&chip->lock);
 			ret = ad7746_store_cap_filter_rate_setup(chip, val);
-			break;
+			mutex_unlock(&chip->lock);
+			return ret;
 		case IIO_VOLTAGE:
+			mutex_lock(&chip->lock);
 			ret = ad7746_store_vt_filter_rate_setup(chip, val);
-			break;
+			mutex_unlock(&chip->lock);
+			return ret;
 		default:
-			ret = -EINVAL;
+			return -EINVAL;
 		}
+	default:
+		return -EINVAL;
+	}
+}
+
 static int ad7746_read_channel(struct iio_dev *indio_dev,
 			       struct iio_chan_spec const *chan,
 			       int *val)
@@ -552,17 +555,16 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 	int ret, idx;
 	u8 reg;
 
-	mutex_lock(&chip->lock);
-
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
 	case IIO_CHAN_INFO_PROCESSED:
+		mutex_lock(&chip->lock);
 		ret = ad7746_read_channel(indio_dev, chan, val);
+		mutex_unlock(&chip->lock);
 		if (ret < 0)
-			goto out;
+			return ret;
 
-		ret = IIO_VAL_INT;
-		break;
+		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_CALIBSCALE:
 		switch (chan->type) {
 		case IIO_CAPACITANCE:
@@ -572,80 +574,69 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 			reg = AD7746_REG_VOLT_GAINH;
 			break;
 		default:
-			ret = -EINVAL;
-			goto out;
+			return -EINVAL;
 		}
 
+		mutex_lock(&chip->lock);
 		ret = i2c_smbus_read_word_swapped(chip->client, reg);
+		mutex_unlock(&chip->lock);
 		if (ret < 0)
-			goto out;
+			return ret;
 		/* 1 + gain_val / 2^16 */
 		*val = 1;
 		*val2 = (15625 * ret) / 1024;
 
-		ret = IIO_VAL_INT_PLUS_MICRO;
-		break;
+		return IIO_VAL_INT_PLUS_MICRO;
 	case IIO_CHAN_INFO_CALIBBIAS:
+		mutex_lock(&chip->lock);
 		ret = i2c_smbus_read_word_swapped(chip->client,
 						  AD7746_REG_CAP_OFFH);
+		mutex_unlock(&chip->lock);
 		if (ret < 0)
-			goto out;
+			return ret;
 		*val = ret;
 
-		ret = IIO_VAL_INT;
-		break;
+		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_OFFSET:
 		*val = AD7746_CAPDAC_DACP(chip->capdac[chan->channel]
 					  [chan->differential]) * 338646;
 
-		ret = IIO_VAL_INT;
-		break;
+		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SCALE:
 		switch (chan->type) {
 		case IIO_CAPACITANCE:
 			/* 8.192pf / 2^24 */
 			*val =  0;
 			*val2 = 488;
-			ret = IIO_VAL_INT_PLUS_NANO;
-			break;
+			return IIO_VAL_INT_PLUS_NANO;
 		case IIO_VOLTAGE:
 			/* 1170mV / 2^23 */
 			*val = 1170;
 			if (chan->channel == 1)
 				*val *= 6;
 			*val2 = 23;
-			ret = IIO_VAL_FRACTIONAL_LOG2;
-			break;
+			return IIO_VAL_FRACTIONAL_LOG2;
 		default:
-			ret = -EINVAL;
-			break;
+			return -EINVAL;
 		}
-
-		break;
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		switch (chan->type) {
 		case IIO_CAPACITANCE:
 			idx = (chip->config & AD7746_CONF_CAPFS_MASK) >>
 				AD7746_CONF_CAPFS_SHIFT;
 			*val = ad7746_cap_filter_rate_table[idx][0];
-			ret = IIO_VAL_INT;
-			break;
+			return IIO_VAL_INT;
 		case IIO_VOLTAGE:
 			idx = (chip->config & AD7746_CONF_VTFS_MASK) >>
 				AD7746_CONF_VTFS_SHIFT;
 			*val = ad7746_vt_filter_rate_table[idx][0];
-			ret = IIO_VAL_INT;
-			break;
+			return IIO_VAL_INT;
 		default:
-			ret = -EINVAL;
+			return -EINVAL;
 		}
-		break;
 	default:
-		ret = -EINVAL;
+		return -EINVAL;
 	}
-out:
-	mutex_unlock(&chip->lock);
-	return ret;
 }
 
 static const struct iio_info ad7746_info = {
Signature · 1 line
2.35.3
author maintainer
#11 lore raw

PATCH 8/17 staging: iio: cdc: ad7746: Break up use of chan->address and use FIELD_PREP etc

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Instead of encoding several different fields into chan->address use an indirection to a separate per channel structure where the various fields can be expressed in a more readable form. This also allows the register values to be constructed at runtime using FIELD_PREP()

Drop the now redundant _SHIFT macros.

---
 drivers/staging/iio/cdc/ad7746.c | 152 ++++++++++++++++++++-----------
 1 file changed, 99 insertions(+), 53 deletions(-)
drivers/staging/iio/cdc/ad7746.c +99 -53
index 34e19677d1fe..bbb7b7db48a2 100644
@@ -5,6 +5,7 @@
  * Copyright 2011 Analog Devices Inc.
  */
 
+#include <linux/bitfield.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/i2c.h>
@@ -48,11 +49,12 @@
 #define AD7746_CAPSETUP_CACHOP		BIT(0)
 
 /* Voltage/Temperature Setup Register Bit Designations (AD7746_REG_VT_SETUP) */
-#define AD7746_VTSETUP_VTEN		(1 << 7)
-#define AD7746_VTSETUP_VTMD_INT_TEMP	(0 << 5)
-#define AD7746_VTSETUP_VTMD_EXT_TEMP	(1 << 5)
-#define AD7746_VTSETUP_VTMD_VDD_MON	(2 << 5)
-#define AD7746_VTSETUP_VTMD_EXT_VIN	(3 << 5)
+#define AD7746_VTSETUP_VTEN		BIT(7)
+#define AD7746_VTSETUP_VTMD_MASK	GENMASK(6, 5)
+#define AD7746_VTSETUP_VTMD_INT_TEMP	0
+#define AD7746_VTSETUP_VTMD_EXT_TEMP	1
+#define AD7746_VTSETUP_VTMD_VDD_MON	2
+#define AD7746_VTSETUP_VTMD_EXT_VIN	3
 #define AD7746_VTSETUP_EXTREF		BIT(4)
 #define AD7746_VTSETUP_VTSHORT		BIT(1)
 #define AD7746_VTSETUP_VTCHOP		BIT(0)
@@ -64,23 +66,22 @@
 #define AD7746_EXCSETUP_NEXCB		BIT(4)
 #define AD7746_EXCSETUP_EXCA		BIT(3)
 #define AD7746_EXCSETUP_NEXCA		BIT(2)
-#define AD7746_EXCSETUP_EXCLVL(x)	(((x) & 0x3) << 0)
+#define AD7746_EXCSETUP_EXCLVL_MASK	GENMASK(1, 0)
 
 /* Config Register Bit Designations (AD7746_REG_CFG) */
-#define AD7746_CONF_VTFS_SHIFT		6
-#define AD7746_CONF_CAPFS_SHIFT		3
 #define AD7746_CONF_VTFS_MASK		GENMASK(7, 6)
 #define AD7746_CONF_CAPFS_MASK		GENMASK(5, 3)
-#define AD7746_CONF_MODE_IDLE		(0 << 0)
-#define AD7746_CONF_MODE_CONT_CONV	(1 << 0)
-#define AD7746_CONF_MODE_SINGLE_CONV	(2 << 0)
-#define AD7746_CONF_MODE_PWRDN		(3 << 0)
-#define AD7746_CONF_MODE_OFFS_CAL	(5 << 0)
-#define AD7746_CONF_MODE_GAIN_CAL	(6 << 0)
+#define AD7746_CONF_MODE_MASK		GENMASK(2, 0)
+#define AD7746_CONF_MODE_IDLE		0
+#define AD7746_CONF_MODE_CONT_CONV	1
+#define AD7746_CONF_MODE_SINGLE_CONV	2
+#define AD7746_CONF_MODE_PWRDN		3
+#define AD7746_CONF_MODE_OFFS_CAL	5
+#define AD7746_CONF_MODE_GAIN_CAL	6
 
 /* CAPDAC Register Bit Designations (AD7746_REG_CAPDACx) */
 #define AD7746_CAPDAC_DACEN		BIT(7)
-#define AD7746_CAPDAC_DACP(x)		((x) & 0x7F)
+#define AD7746_CAPDAC_DACP_MASK		0x7F
 
 struct ad7746_chip_info {
 	struct i2c_client *client;
@@ -107,6 +108,52 @@ enum ad7746_chan {
 	CIN2_DIFF,
 };
 
+struct ad7746_chan_info {
+	u8 addr;
+	union {
+		u8 vtmd;
+		struct { /* CAP SETUP fields */
+			unsigned int cin2 : 1;
+			unsigned int capdiff : 1;
+		};
+	};
+};
+
+static const struct ad7746_chan_info ad7746_chan_info[] = {
+	[VIN] = {
+		.addr = AD7746_REG_VT_DATA_HIGH,
+		.vtmd = AD7746_VTSETUP_VTMD_EXT_VIN,
+	},
+	[VIN_VDD] = {
+		.addr = AD7746_REG_VT_DATA_HIGH,
+		.vtmd = AD7746_VTSETUP_VTMD_VDD_MON,
+	},
+	[TEMP_INT] = {
+		.addr = AD7746_REG_VT_DATA_HIGH,
+		.vtmd = AD7746_VTSETUP_VTMD_INT_TEMP,
+	},
+	[TEMP_EXT] = {
+		.addr = AD7746_REG_VT_DATA_HIGH,
+		.vtmd = AD7746_VTSETUP_VTMD_EXT_TEMP,
+	},
+	[CIN1] = {
+		.addr = AD7746_REG_CAP_DATA_HIGH,
+	},
+	[CIN1_DIFF] = {
+		.addr =  AD7746_REG_CAP_DATA_HIGH,
+		.capdiff = 1,
+	},
+	[CIN2] = {
+		.addr = AD7746_REG_CAP_DATA_HIGH,
+		.cin2 = 1,
+	},
+	[CIN2_DIFF] = {
+		.addr = AD7746_REG_CAP_DATA_HIGH,
+		.cin2 = 1,
+		.capdiff = 1,
+	},
+};
+
 static const struct iio_chan_spec ad7746_channels[] = {
 	[VIN] = {
 		.type = IIO_VOLTAGE,
@@ -114,8 +161,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.channel = 0,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
-		.address = AD7746_REG_VT_DATA_HIGH << 8 |
-			AD7746_VTSETUP_VTMD_EXT_VIN,
+		.address = VIN,
 	},
 	[VIN_VDD] = {
 		.type = IIO_VOLTAGE,
@@ -124,24 +170,21 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.extend_name = "supply",
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
-		.address = AD7746_REG_VT_DATA_HIGH << 8 |
-			AD7746_VTSETUP_VTMD_VDD_MON,
+		.address = VIN_VDD,
 	},
 	[TEMP_INT] = {
 		.type = IIO_TEMP,
 		.indexed = 1,
 		.channel = 0,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
-		.address = AD7746_REG_VT_DATA_HIGH << 8 |
-			AD7746_VTSETUP_VTMD_INT_TEMP,
+		.address = TEMP_INT,
 	},
 	[TEMP_EXT] = {
 		.type = IIO_TEMP,
 		.indexed = 1,
 		.channel = 1,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
-		.address = AD7746_REG_VT_DATA_HIGH << 8 |
-			AD7746_VTSETUP_VTMD_EXT_TEMP,
+		.address = TEMP_EXT,
 	},
 	[CIN1] = {
 		.type = IIO_CAPACITANCE,
@@ -151,7 +194,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
-		.address = AD7746_REG_CAP_DATA_HIGH << 8,
+		.address = CIN1,
 	},
 	[CIN1_DIFF] = {
 		.type = IIO_CAPACITANCE,
@@ -163,8 +206,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
-		.address = AD7746_REG_CAP_DATA_HIGH << 8 |
-			AD7746_CAPSETUP_CAPDIFF
+		.address = CIN1_DIFF,
 	},
 	[CIN2] = {
 		.type = IIO_CAPACITANCE,
@@ -174,8 +216,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
-		.address = AD7746_REG_CAP_DATA_HIGH << 8 |
-			AD7746_CAPSETUP_CIN2,
+		.address = CIN2,
 	},
 	[CIN2_DIFF] = {
 		.type = IIO_CAPACITANCE,
@@ -187,8 +228,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
-		.address = AD7746_REG_CAP_DATA_HIGH << 8 |
-			AD7746_CAPSETUP_CAPDIFF | AD7746_CAPSETUP_CIN2,
+		.address = CIN2_DIFF,
 	}
 };
 
@@ -224,10 +264,13 @@ static int ad7746_select_channel(struct iio_dev *indio_dev,
 
 	switch (chan->type) {
 	case IIO_CAPACITANCE:
-		cap_setup = (chan->address & 0xFF) | AD7746_CAPSETUP_CAPEN;
+		cap_setup = FIELD_PREP(AD7746_CAPSETUP_CIN2,
+				       ad7746_chan_info[chan->address].cin2) |
+			FIELD_PREP(AD7746_CAPSETUP_CAPDIFF,
+				   ad7746_chan_info[chan->address].capdiff) |
+			FIELD_PREP(AD7746_CAPSETUP_CAPEN, 1);
 		vt_setup = chip->vt_setup & ~AD7746_VTSETUP_VTEN;
-		idx = (chip->config & AD7746_CONF_CAPFS_MASK) >>
-			AD7746_CONF_CAPFS_SHIFT;
+		idx = FIELD_GET(AD7746_CONF_CAPFS_MASK, chip->config);
 		delay = ad7746_cap_filter_rate_table[idx][1];
 
 		ret = ad7746_set_capdac(chip, chan->channel);
@@ -239,10 +282,11 @@ static int ad7746_select_channel(struct iio_dev *indio_dev,
 		break;
 	case IIO_VOLTAGE:
 	case IIO_TEMP:
-		vt_setup = (chan->address & 0xFF) | AD7746_VTSETUP_VTEN;
+		vt_setup = FIELD_PREP(AD7746_VTSETUP_VTMD_MASK,
+				      ad7746_chan_info[chan->address].vtmd) |
+			FIELD_PREP(AD7746_VTSETUP_VTEN, 1);
 		cap_setup = chip->cap_setup & ~AD7746_CAPSETUP_CAPEN;
-		idx = (chip->config & AD7746_CONF_VTFS_MASK) >>
-			AD7746_CONF_VTFS_SHIFT;
+		idx = FIELD_GET(AD7746_CONF_VTFS_MASK, chip->config);
 		delay = ad7746_cap_filter_rate_table[idx][1];
 		break;
 	default:
@@ -325,7 +369,8 @@ static ssize_t ad7746_start_offset_calib(struct device *dev,
 		return ret;
 
 	return ad7746_start_calib(dev, attr, buf, len,
-				  AD7746_CONF_MODE_OFFS_CAL);
+				  FIELD_PREP(AD7746_CONF_MODE_MASK,
+					     AD7746_CONF_MODE_OFFS_CAL));
 }
 
 static ssize_t ad7746_start_gain_calib(struct device *dev,
@@ -340,7 +385,8 @@ static ssize_t ad7746_start_gain_calib(struct device *dev,
 		return ret;
 
 	return ad7746_start_calib(dev, attr, buf, len,
-				  AD7746_CONF_MODE_GAIN_CAL);
+				  FIELD_PREP(AD7746_CONF_MODE_MASK,
+					     AD7746_CONF_MODE_GAIN_CAL));
 }
 
 static IIO_DEVICE_ATTR(in_capacitance0_calibbias_calibration,
@@ -367,7 +413,7 @@ static int ad7746_store_cap_filter_rate_setup(struct ad7746_chip_info *chip,
 		i = ARRAY_SIZE(ad7746_cap_filter_rate_table) - 1;
 
 	chip->config &= ~AD7746_CONF_CAPFS_MASK;
-	chip->config |= i << AD7746_CONF_CAPFS_SHIFT;
+	chip->config |= FIELD_PREP(AD7746_CONF_CAPFS_MASK, i);
 
 	return 0;
 }
@@ -385,7 +431,7 @@ static int ad7746_store_vt_filter_rate_setup(struct ad7746_chip_info *chip,
 		i = ARRAY_SIZE(ad7746_vt_filter_rate_table) - 1;
 
 	chip->config &= ~AD7746_CONF_VTFS_MASK;
-	chip->config |= i << AD7746_CONF_VTFS_SHIFT;
+	chip->config |= FIELD_PREP(AD7746_CONF_VTFS_MASK, i);
 
 	return 0;
 }
@@ -468,7 +514,7 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 		val /= 338646;
 		mutex_lock(&chip->lock);
 		chip->capdac[chan->channel][chan->differential] = val > 0 ?
-			AD7746_CAPDAC_DACP(val) | AD7746_CAPDAC_DACEN : 0;
+			FIELD_PREP(AD7746_CAPDAC_DACP_MASK, val) | AD7746_CAPDAC_DACEN : 0;
 
 		ret = ad7746_set_capdac(chip, chan->channel);
 		if (ret < 0) {
@@ -517,14 +563,16 @@ static int ad7746_read_channel(struct iio_dev *indio_dev,
 		return ret;
 	delay = ret;
 
-	regval = chip->config | AD7746_CONF_MODE_SINGLE_CONV;
+	regval = chip->config | FIELD_PREP(AD7746_CONF_MODE_MASK,
+					   AD7746_CONF_MODE_SINGLE_CONV);
 	ret = i2c_smbus_write_byte_data(chip->client, AD7746_REG_CFG, regval);
 	if (ret < 0)
 		return ret;
 
 	msleep(delay);
 	/* Now read the actual register */
-	ret = i2c_smbus_read_i2c_block_data(chip->client,  chan->address >> 8,
+	ret = i2c_smbus_read_i2c_block_data(chip->client,
+					    ad7746_chan_info[chan->address].addr,
 					    3, data);
 	if (ret < 0)
 		return ret;
@@ -598,8 +646,8 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_OFFSET:
-		*val = AD7746_CAPDAC_DACP(chip->capdac[chan->channel]
-					  [chan->differential]) * 338646;
+		*val = FIELD_GET(AD7746_CAPDAC_DACP_MASK,
+				 chip->capdac[chan->channel][chan->differential]) * 338646;
 
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_SCALE:
@@ -622,13 +670,11 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 	case IIO_CHAN_INFO_SAMP_FREQ:
 		switch (chan->type) {
 		case IIO_CAPACITANCE:
-			idx = (chip->config & AD7746_CONF_CAPFS_MASK) >>
-				AD7746_CONF_CAPFS_SHIFT;
+			idx = FIELD_GET(AD7746_CONF_CAPFS_MASK, chip->config);
 			*val = ad7746_cap_filter_rate_table[idx][0];
 			return IIO_VAL_INT;
 		case IIO_VOLTAGE:
-			idx = (chip->config & AD7746_CONF_VTFS_MASK) >>
-				AD7746_CONF_VTFS_SHIFT;
+			idx = FIELD_GET(AD7746_CONF_VTFS_MASK, chip->config);
 			*val = ad7746_vt_filter_rate_table[idx][0];
 			return IIO_VAL_INT;
 		default:
@@ -694,16 +740,16 @@ static int ad7746_probe(struct i2c_client *client,
 	if (!ret) {
 		switch (vdd_permille) {
 		case 125:
-			regval |= AD7746_EXCSETUP_EXCLVL(0);
+			regval |= FIELD_PREP(AD7746_EXCSETUP_EXCLVL_MASK, 0);
 			break;
 		case 250:
-			regval |= AD7746_EXCSETUP_EXCLVL(1);
+			regval |= FIELD_PREP(AD7746_EXCSETUP_EXCLVL_MASK, 1);
 			break;
 		case 375:
-			regval |= AD7746_EXCSETUP_EXCLVL(2);
+			regval |= FIELD_PREP(AD7746_EXCSETUP_EXCLVL_MASK, 2);
 			break;
 		case 500:
-			regval |= AD7746_EXCSETUP_EXCLVL(3);
+			regval |= FIELD_PREP(AD7746_EXCSETUP_EXCLVL_MASK, 3);
 			break;
 		default:
 			break;
Signature · 1 line
2.35.3
author maintainer
#12 lore raw

PATCH 9/17 staging: iio: cdc: ad7746: Drop usused i2c_set_clientdata()

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

As the comment states, this was only used in remove() and now there is no explicit remove() function to make use of it.

---
 drivers/staging/iio/cdc/ad7746.c | 2 --
 1 file changed, 2 deletions(-)
drivers/staging/iio/cdc/ad7746.c +0 -2
index bbb7b7db48a2..f6b54e817973 100644
@@ -706,8 +706,6 @@ static int ad7746_probe(struct i2c_client *client,
 		return -ENOMEM;
 	chip = iio_priv(indio_dev);
 	mutex_init(&chip->lock);
-	/* this is only used for device removal purposes */
-	i2c_set_clientdata(client, indio_dev);
 
 	chip->client = client;
 	chip->capdac_set = -1;
Signature · 1 line
2.35.3
author maintainer
#13 lore raw

PATCH 10/17 staging: iio: cdc: ad7746: Use _raw and _scale for temperature channels.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Performing the maths to rescale a 24 bit raw reading within the driver was resulting in precision losses. So make that userspace's problem by exporting the scale and letting the maths be done in userspace with appropriate precision. Issue identified using roadtester testing framework.

---
 drivers/staging/iio/cdc/ad7746.c | 23 ++++++++---------------
 1 file changed, 8 insertions(+), 15 deletions(-)
drivers/staging/iio/cdc/ad7746.c +8 -15
index f6b54e817973..0dc5630d0655 100644
@@ -176,14 +176,16 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.type = IIO_TEMP,
 		.indexed = 1,
 		.channel = 0,
-		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
 		.address = TEMP_INT,
 	},
 	[TEMP_EXT] = {
 		.type = IIO_TEMP,
 		.indexed = 1,
 		.channel = 1,
-		.info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),
+		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE),
 		.address = TEMP_EXT,
 	},
 	[CIN1] = {
@@ -579,18 +581,6 @@ static int ad7746_read_channel(struct iio_dev *indio_dev,
 
 	*val = get_unaligned_be24(data) - 0x800000;
 
-	switch (chan->type) {
-	case IIO_TEMP:
-		/*
-		 * temperature in milli degrees Celsius
-		 * T = ((*val / 2048) - 4096) * 1000
-		 */
-		*val = (*val  * 125) / 256;
-		break;
-	default:
-		break;
-	}
-
 	return 0;
 }
 
@@ -605,7 +595,6 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
-	case IIO_CHAN_INFO_PROCESSED:
 		mutex_lock(&chip->lock);
 		ret = ad7746_read_channel(indio_dev, chan, val);
 		mutex_unlock(&chip->lock);
@@ -664,6 +653,10 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 				*val *= 6;
 			*val2 = 23;
 			return IIO_VAL_FRACTIONAL_LOG2;
+		case IIO_TEMP:
+			*val = 125;
+			*val2 = 8;
+			return IIO_VAL_FRACTIONAL_LOG2;
 		default:
 			return -EINVAL;
 		}
Signature · 1 line
2.35.3
author maintainer
#14 lore raw

PATCH 11/17 iio: core: Introduce _inputoffset for differential channels

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Address an ABI gap for device where the offset of both lines in a differential pair may be controlled so as to allow a wider range of inputs, but without having any direct effect of the differential measurement.

_offset cannot be used as to remain in line with existing usage, userspace would be expected to apply it as (_raw + _offset) * scale whereas _inputoffset is not.
Similarly calibbias is expected to tweak the measurement seen, not the adjust the two lines of the differential pair.

Needed for in_capacitanceX-capacitanceY_inputoffset for the AD7746 CDC driver.

---
I''m not entirely happy with the naming on this one, so if anyone has a better idea I'm definitely open to it!

---
 Documentation/ABI/testing/sysfs-bus-iio | 13 +++++++++++++
 drivers/iio/industrialio-core.c         |  1 +
 include/linux/iio/types.h               |  1 +
 3 files changed, 15 insertions(+)
Documentation/ABI/testing/sysfs-bus-iio +13 -0
index b19ff517e5d6..4fbb5a257ef5 100644
@@ -199,6 +199,19 @@ Description:
 		is required is a consistent labeling.  Units after application
 		of scale and offset are nanofarads.
 
+What:		/sys/.../iio:deviceX/in_capacitableY-capacitanceZ_inputoffset
+KernelVersion:	5.19
+Contact:	[email protected]
+Description:
+		For differential channels, this an offset that is applied
+		equally to both inputs. As the reading is of the difference
+		between the two inputs this should not be applied to the _raw
+		reading by userspace (unlike _offset) and unlike calibbias
+		it does not affect the differential value measured because
+		the effect of _inputoffset cancels out across the two inputs
+		that make up the differential pair. It is expressed with
+		the same scaling as _raw.
+
 What:		/sys/bus/iio/devices/iio:deviceX/in_temp_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_tempX_raw
 What:		/sys/bus/iio/devices/iio:deviceX/in_temp_x_raw
drivers/iio/industrialio-core.c +1 -0
index d831835770da..8aebef08ca1d 100644
@@ -168,6 +168,7 @@ static const char * const iio_chan_info_postfix[] = {
 	[IIO_CHAN_INFO_OVERSAMPLING_RATIO] = "oversampling_ratio",
 	[IIO_CHAN_INFO_THERMOCOUPLE_TYPE] = "thermocouple_type",
 	[IIO_CHAN_INFO_CALIBAMBIENT] = "calibambient",
+	[IIO_CHAN_INFO_INPUTOFFSET] = "inputoffset",
 };
 /**
  * iio_device_id() - query the unique ID for the device
include/linux/iio/types.h +1 -0
index a7aa91f3a8dc..c7f79a251a14 100644
@@ -63,6 +63,7 @@ enum iio_chan_info_enum {
 	IIO_CHAN_INFO_OVERSAMPLING_RATIO,
 	IIO_CHAN_INFO_THERMOCOUPLE_TYPE,
 	IIO_CHAN_INFO_CALIBAMBIENT,
+	IIO_CHAN_INFO_INPUTOFFSET,
 };
 
 #endif /* _IIO_TYPES_H_ */
Signature · 1 line
2.35.3
author maintainer
#15 lore raw

PATCH 12/17 staging: iio: cdc: ad7746: Switch from _offset to _inputoffset for differential channels.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

As this offset is applied equally to both lines of the differential pair, _ofset should not be used. Use the new ABI _inputoffset instead to avoid userspace software applying this value when calculating real value = (_raw + _offset) * _scale

Also add a comment to explain why an offset of 0x800000 is applied within the driver rather than exposed to userspace.

---
 drivers/staging/iio/cdc/ad7746.c | 10 ++++++++--
 1 file changed, 8 insertions(+), 2 deletions(-)
drivers/staging/iio/cdc/ad7746.c +8 -2
index 0dc5630d0655..46cdddab495f 100644
@@ -205,7 +205,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.channel = 0,
 		.channel2 = 2,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
-		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
+		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_INPUTOFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = CIN1_DIFF,
@@ -227,7 +227,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.channel = 1,
 		.channel2 = 3,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
-		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
+		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_INPUTOFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = CIN2_DIFF,
@@ -504,6 +504,7 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 
 		return 0;
 	case IIO_CHAN_INFO_OFFSET:
+	case IIO_CHAN_INFO_INPUTOFFSET:
 		if (val < 0 || val > 43008000) /* 21pF */
 			return -EINVAL;
 
@@ -579,6 +580,10 @@ static int ad7746_read_channel(struct iio_dev *indio_dev,
 	if (ret < 0)
 		return ret;
 
+	/*
+	 * Offset applied internally becaue the _offset userspace interface is
+	 * needed for the CAP DACs which apply a controllable offset.
+	 */
 	*val = get_unaligned_be24(data) - 0x800000;
 
 	return 0;
@@ -635,6 +640,7 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 
 		return IIO_VAL_INT;
 	case IIO_CHAN_INFO_OFFSET:
+	case IIO_CHAN_INFO_INPUTOFFSET:
 		*val = FIELD_GET(AD7746_CAPDAC_DACP_MASK,
 				 chip->capdac[chan->channel][chan->differential]) * 338646;
 
Signature · 1 line
2.35.3
author maintainer
#16 lore raw

PATCH 13/17 staging: iio: cdc: ad7746: Use read_avail() rather than opencoding.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Switch over to the IIO core handling for _available attributes making them available for in kernel users and enforcing correct naming etc automatically.

---
 drivers/staging/iio/cdc/ad7746.c | 39 +++++++++++++++++++++++++++-----
 1 file changed, 33 insertions(+), 6 deletions(-)
drivers/staging/iio/cdc/ad7746.c +33 -6
index 46cdddab495f..6fe3221c8ace 100644
@@ -161,6 +161,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.channel = 0,
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = VIN,
 	},
 	[VIN_VDD] = {
@@ -170,6 +171,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		.extend_name = "supply",
 		.info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | BIT(IIO_CHAN_INFO_SCALE),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = VIN_VDD,
 	},
 	[TEMP_INT] = {
@@ -196,6 +198,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = CIN1,
 	},
 	[CIN1_DIFF] = {
@@ -208,6 +211,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_INPUTOFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = CIN1_DIFF,
 	},
 	[CIN2] = {
@@ -218,6 +222,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_OFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = CIN2,
 	},
 	[CIN2_DIFF] = {
@@ -230,6 +235,7 @@ static const struct iio_chan_spec ad7746_channels[] = {
 		BIT(IIO_CHAN_INFO_CALIBSCALE) | BIT(IIO_CHAN_INFO_INPUTOFFSET),
 		.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_CALIBBIAS) |
 		BIT(IIO_CHAN_INFO_SCALE) | BIT(IIO_CHAN_INFO_SAMP_FREQ),
+		.info_mask_shared_by_type_available = BIT(IIO_CHAN_INFO_SAMP_FREQ),
 		.address = CIN2_DIFF,
 	}
 };
@@ -438,18 +444,12 @@ static int ad7746_store_vt_filter_rate_setup(struct ad7746_chip_info *chip,
 	return 0;
 }
 
-static IIO_CONST_ATTR(in_voltage_sampling_frequency_available, "50 31 16 8");
-static IIO_CONST_ATTR(in_capacitance_sampling_frequency_available,
-		       "91 84 50 26 16 13 11 9");
-
 static struct attribute *ad7746_attributes[] = {
 	&iio_dev_attr_in_capacitance0_calibbias_calibration.dev_attr.attr,
 	&iio_dev_attr_in_capacitance0_calibscale_calibration.dev_attr.attr,
 	&iio_dev_attr_in_capacitance1_calibscale_calibration.dev_attr.attr,
 	&iio_dev_attr_in_capacitance1_calibbias_calibration.dev_attr.attr,
 	&iio_dev_attr_in_voltage0_calibscale_calibration.dev_attr.attr,
-	&iio_const_attr_in_voltage_sampling_frequency_available.dev_attr.attr,
-	&iio_const_attr_in_capacitance_sampling_frequency_available.dev_attr.attr,
 	NULL,
 };
 
@@ -552,6 +552,32 @@ static int ad7746_write_raw(struct iio_dev *indio_dev,
 	}
 }
 
+static const int ad7746_v_samp_freq[] = { 50, 31, 16, 8, };
+static const int ad7746_cap_samp_freq[] = { 91, 84, 50, 26, 16, 13, 11, 9, };
+
+static int ad7746_read_avail(struct iio_dev *indio_dev,
+			     struct iio_chan_spec const *chan, const int **vals,
+			     int *type, int *length, long mask)
+{
+	if (mask != IIO_CHAN_INFO_SAMP_FREQ)
+		return -EINVAL;
+
+	switch (chan->type) {
+	case IIO_VOLTAGE:
+		*vals = ad7746_v_samp_freq;
+		*length = ARRAY_SIZE(ad7746_v_samp_freq);
+		break;
+	case IIO_CAPACITANCE:
+		*vals = ad7746_cap_samp_freq;
+		*length = ARRAY_SIZE(ad7746_cap_samp_freq);
+		break;
+	default:
+		return -EINVAL;
+	}
+	*type = IIO_VAL_INT;
+	return IIO_AVAIL_LIST;
+}
+
 static int ad7746_read_channel(struct iio_dev *indio_dev,
 			       struct iio_chan_spec const *chan,
 			       int *val)
@@ -687,6 +713,7 @@ static int ad7746_read_raw(struct iio_dev *indio_dev,
 static const struct iio_info ad7746_info = {
 	.attrs = &ad7746_attribute_group,
 	.read_raw = ad7746_read_raw,
+	.read_avail = ad7746_read_avail,
 	.write_raw = ad7746_write_raw,
 };
 
Signature · 1 line
2.35.3
author maintainer
#17 lore raw

PATCH 14/17 staging: iio: ad7746: White space cleanup

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

Tidy up some trivial whitespace issues.

---
 drivers/staging/iio/cdc/ad7746.c | 17 +++++++----------
 1 file changed, 7 insertions(+), 10 deletions(-)
drivers/staging/iio/cdc/ad7746.c +7 -10
index 6fe3221c8ace..058f1b74122e 100644
@@ -19,9 +19,7 @@
 #include <linux/iio/iio.h>
 #include <linux/iio/sysfs.h>
 
-/*
- * AD7746 Register Definition
- */
+/* AD7746 Register Definition */
 
 #define AD7746_REG_STATUS		0
 #define AD7746_REG_CAP_DATA_HIGH	1
@@ -242,12 +240,12 @@ static const struct iio_chan_spec ad7746_channels[] = {
 
 /* Values are Update Rate (Hz), Conversion Time (ms) + 1*/
 static const unsigned char ad7746_vt_filter_rate_table[][2] = {
-	{50, 20 + 1}, {31, 32 + 1}, {16, 62 + 1}, {8, 122 + 1},
+	{ 50, 20 + 1 }, { 31, 32 + 1 }, { 16, 62 + 1 }, { 8, 122 + 1 },
 };
 
 static const unsigned char ad7746_cap_filter_rate_table[][2] = {
-	{91, 11 + 1}, {84, 12 + 1}, {50, 20 + 1}, {26, 38 + 1},
-	{16, 62 + 1}, {13, 77 + 1}, {11, 92 + 1}, {9, 110 + 1},
+	{ 91, 11 + 1 }, { 84, 12 + 1 }, { 50, 20 + 1 }, { 26, 38 + 1 },
+	{ 16, 62 + 1 }, { 13, 77 + 1 }, { 11, 92 + 1 }, { 9, 110 + 1 },
 };
 
 static int ad7746_set_capdac(struct ad7746_chip_info *chip, int channel)
@@ -730,6 +728,7 @@ static int ad7746_probe(struct i2c_client *client,
 	indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*chip));
 	if (!indio_dev)
 		return -ENOMEM;
+
 	chip = iio_priv(indio_dev);
 	mutex_init(&chip->lock);
 
@@ -780,8 +779,8 @@ static int ad7746_probe(struct i2c_client *client,
 		}
 	}
 
-	ret = i2c_smbus_write_byte_data(chip->client,
-					AD7746_REG_EXC_SETUP, regval);
+	ret = i2c_smbus_write_byte_data(chip->client, AD7746_REG_EXC_SETUP,
+					regval);
 	if (ret < 0)
 		return ret;
 
@@ -794,7 +793,6 @@ static const struct i2c_device_id ad7746_id[] = {
 	{ "ad7747", 7747 },
 	{}
 };
-
 MODULE_DEVICE_TABLE(i2c, ad7746_id);
 
 static const struct of_device_id ad7746_of_match[] = {
@@ -803,7 +801,6 @@ static const struct of_device_id ad7746_of_match[] = {
 	{ .compatible = "adi,ad7747" },
 	{ },
 };
-
 MODULE_DEVICE_TABLE(of, ad7746_of_match);
 
 static struct i2c_driver ad7746_driver = {
Signature · 1 line
2.35.3
author maintainer
#18 lore raw

PATCH 15/17 iio: cdc: ad7746: Add device specific ABI documentation.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

The datasheet description of offset calibration is complex, so for that on just refer the reader to the device datasheet.

---
 Documentation/ABI/testing/sysfs-bus-iio-cdc-ad7746 | 11 +++++++++++
 1 file changed, 11 insertions(+)
Documentation/ABI/testing/sysfs-bus-iio-cdc-ad7746 new file +11 -0
new file mode 100644
index 000000000000..6db81725b5d2
@@ -0,0 +1,11 @@
+What:		/sys/.../iio:deviceX/in_capacitableY_calibbias_calibration
+What:		/sys/.../iio:deviceX/in_capacitableY_calibscale_calibration
+KernelVersion:	5.19
+Contact:	[email protected]
+Description:
+		Write 1 to trigger a calibration of the calibbias or
+		calibscale. For calibscale, a fullscale capacitance should
+		be connected to the capacitance input and a
+		calibscale_calibration then started.  For calibbias see
+		the device datasheet section on "capacitive system offset
+		calibration".
Signature · 1 line
2.35.3
author maintainer
#19 lore raw

PATCH 16/17 iio: cdc: ad7746: Move driver out of staging.

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

All known major issues with this driver resolved so time to move it out of staging.

Note this cleanup work was done using the roadtest framework.
https://lore.kernel.org/all/[email protected]/

---
 drivers/iio/cdc/Kconfig          |  10 +
 drivers/iio/cdc/Makefile         |   1 +
 drivers/iio/cdc/ad7746.c         | 818 +++++++++++++++++++++++++++++++
 drivers/staging/iio/cdc/ad7746.c | 818 -------------------------------
 4 files changed, 829 insertions(+), 818 deletions(-)
drivers/iio/cdc/Kconfig +10 -0
index 5e3319a3ff48..e0a5ce66a984 100644
@@ -14,4 +14,14 @@ config AD7150
 	  To compile this driver as a module, choose M here: the
 	  module will be called ad7150.
 
+config AD7746
+	tristate "Analog Devices AD7745, AD7746 AD7747 capacitive sensor driver"
+	depends on I2C
+	help
+	  Say yes here to build support for Analog Devices capacitive sensors.
+	  (AD7745, AD7746, AD7747) Provides direct access via sysfs.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ad7746.
+
 endmenu
drivers/iio/cdc/Makefile +1 -0
index ee490637b032..41db756d8020 100644
@@ -4,3 +4,4 @@
 #
 
 obj-$(CONFIG_AD7150) += ad7150.o
+obj-$(CONFIG_AD7746) += ad7746.o
drivers/iio/cdc/ad7746.c new file +818 -0

818 lines not on this page · raw message

drivers/staging/iio/cdc/ad7746.c deleted +0 -818

818 lines not on this page · raw message

Signature · 1 line
2.35.3
author maintainer
#20 lore raw

PATCH 17/17 RFC: iio: cdc: ad7746: Add roadtest

In reply to Jonathan Cameron

From: Jonathan Cameron <[email protected]>

The recent work to cleanup and migrate this driver out of staging relied on using roadtest to verify that the various refactoring and fixes did not cause any regressions.

Note I am far from an experienced python coder so a large part of this exercise was to establish if roadtest was useful / usable without that particular skill set. Conclusion yes it is :)

Apologies for the code!

---
 .../roadtest/tests/iio/cdc/__init__.py        |   0
 .../roadtest/roadtest/tests/iio/cdc/config    |   1 +
 .../roadtest/tests/iio/cdc/test_ad7746.py     | 323 ++++++++++++++++++
 3 files changed, 324 insertions(+)
tools/testing/roadtest/roadtest/tests/iio/cdc/__init__.py new file +0 -0
new file mode 100644
index 000000000000..e69de29bb2d1
tools/testing/roadtest/roadtest/tests/iio/cdc/config new file +1 -0
new file mode 100644
index 000000000000..6e9397325918
@@ -0,0 +1 @@
+CONFIG_AD7746=m
tools/testing/roadtest/roadtest/tests/iio/cdc/test_ad7746.py new file +323 -0

323 lines not on this page · raw message

Signature · 1 line
2.35.3