dt-bindings: regulator: qcom,spmi-regulator: Convert to dtschema

deleted file mode 100644
index c2a39b121b1b..000000000000
@@ -1,347 +0,0 @@
-Qualcomm SPMI Regulators
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-			"qcom,pm8004-regulators"
-			"qcom,pm8005-regulators"
-			"qcom,pm8226-regulators"
-			"qcom,pm8841-regulators"
-			"qcom,pm8916-regulators"
-			"qcom,pm8941-regulators"
-			"qcom,pm8950-regulators"
-			"qcom,pm8994-regulators"
-			"qcom,pmi8994-regulators"
-			"qcom,pm660-regulators"
-			"qcom,pm660l-regulators"
-			"qcom,pms405-regulators"
-
-- interrupts:
-	Usage: optional
-	Value type: <prop-encoded-array>
-	Definition: List of OCP interrupts.
-
-- interrupt-names:
-	Usage: required if 'interrupts' property present
-	Value type: <string-array>
-	Definition: List of strings defining the names of the
-		    interrupts in the 'interrupts' property 1-to-1.
-		    Supported values are "ocp-<regulator_name>", where
-		    <regulator_name> corresponds to a voltage switch
-		    type regulator.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-	Usage: optional (pm8841 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_l1_l3-supply:
-- vdd_l2-supply:
-- vdd_l4_l5_l6-supply:
-- vdd_l7-supply:
-- vdd_l8_l11_l14_l15_l16-supply:
-- vdd_l9_l10_l12_l13_l17_l18-supply:
-	Usage: optional (pm8916 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_l1_l3-supply:
-- vdd_l2_lvs_1_2_3-supply:
-- vdd_l4_l11-supply:
-- vdd_l5_l7-supply:
-- vdd_l6_l12_l14_l15-supply:
-- vdd_l8_l16_l18_19-supply:
-- vdd_l9_l10_l17_l22-supply:
-- vdd_l13_l20_l23_l24-supply:
-- vdd_l21-supply:
-- vin_5vs-supply:
-	Usage: optional (pm8941 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_l1_l19-supply:
-- vdd_l2_l23-supply:
-- vdd_l3-supply:
-- vdd_l4_l5_l6_l7_l16-supply:
-- vdd_l8_l11_l12_l17_l22-supply:
-- vdd_l9_l10_l13_l14_l15_l18-supply:
-- vdd_l20-supply:
-- vdd_l21-supply:
-	Usage: optional (pm8950 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-- vdd_s9-supply:
-- vdd_s10-supply:
-- vdd_s11-supply:
-- vdd_s12-supply:
-- vdd_l1-supply:
-- vdd_l2_l26_l28-supply:
-- vdd_l3_l11-supply:
-- vdd_l4_l27_l31-supply:
-- vdd_l5_l7-supply:
-- vdd_l6_l12_l32-supply:
-- vdd_l8_l16_l30-supply:
-- vdd_l9_l10_l18_l22-supply:
-- vdd_l13_l19_l23_l24-supply:
-- vdd_l14_l15-supply:
-- vdd_l17_l29-supply:
-- vdd_l20_l21-supply:
-- vdd_l25-supply:
-- vdd_lvs_1_2-supply:
-	Usage: optional (pm8994 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_l1-supply:
-	Usage: optional (pmi8994 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l6_l7-supply:
-- vdd_l2_l3-supply:
-- vdd_l5-supply:
-- vdd_l8_l9_l10_l11_l12_l13_l14-supply:
-- vdd_l15_l16_l17_l18_l19-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-	Usage: optional (pm660 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l9_l10-supply:
-- vdd_l2-supply:
-- vdd_l3_l5_l7_l8-supply:
-- vdd_l4_l6-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-	Usage: optional (pm660l only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l2-supply:
-- vdd_l3_l8-supply:
-- vdd_l4-supply:
-- vdd_l5_l6-supply:
-- vdd_l10_l11_l12_l13-supply:
-- vdd_l7-supply:
-- vdd_l9-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply
-	Usage: optional (pms405 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- qcom,saw-reg:
-	Usage: optional
-	Value type: <phandle>
-	Description: Reference to syscon node defining the SAW registers.
-
-
-The regulator node houses sub-nodes for each regulator within the device. Each
-sub-node is identified using the node's name, with valid values listed for each
-of the PMICs below.
-
-pm8004:
-	s2, s5
-
-pm8005:
-	s1, s2, s3, s4
-
-pm8841:
-	s1, s2, s3, s4, s5, s6, s7, s8
-
-pm8916:
-	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
-	l14, l15, l16, l17, l18
-
-pm8941:
-	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
-	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	5vs1, 5vs2
-
-pm8994:
-	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
-	l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20,
-	l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2
-
-pmi8994:
-	s1, s2, s3, l1
-
-The content of each sub-node is defined by the standard binding for regulators -
-see regulator.txt - with additional custom properties described below:
-
-- regulator-initial-mode:
-	Usage: optional
-	Value type: <u32>
-	Description: 2 = Set initial mode to auto mode (automatically select
-		    between HPM and LPM); not available on boost type
-		    regulators.
-
-		    1 = Set initial mode to high power mode (HPM), also referred
-		    to as NPM. HPM consumes more ground current than LPM, but
-		    it can source significantly higher load current. HPM is not
-		    available on boost type regulators. For voltage switch type
-		    regulators, HPM implies that over current protection and
-		    soft start are active all the time.
-
-		    0 = Set initial mode to low power mode (LPM).
-
-- qcom,ocp-max-retries:
-	Usage: optional
-	Value type: <u32>
-	Description: Maximum number of times to try toggling a voltage switch
-		     off and back on as a result of consecutive over current
-		     events.
-
-- qcom,ocp-retry-delay:
-	Usage: optional
-	Value type: <u32>
-	Description: Time to delay in milliseconds between each voltage switch
-		     toggle after an over current event takes place.
-
-- qcom,pin-ctrl-enable:
-	Usage: optional
-	Value type: <u32>
-	Description: Bit mask specifying which hardware pins should be used to
-		     enable the regulator, if any; supported bits are:
-			0 = ignore all hardware enable signals
-			BIT(0) = follow HW0_EN signal
-			BIT(1) = follow HW1_EN signal
-			BIT(2) = follow HW2_EN signal
-			BIT(3) = follow HW3_EN signal
-
-- qcom,pin-ctrl-hpm:
-	Usage: optional
-	Value type: <u32>
-	Description: Bit mask specifying which hardware pins should be used to
-		     force the regulator into high power mode, if any;
-		     supported bits are:
-			0 = ignore all hardware enable signals
-			BIT(0) = follow HW0_EN signal
-			BIT(1) = follow HW1_EN signal
-			BIT(2) = follow HW2_EN signal
-			BIT(3) = follow HW3_EN signal
-			BIT(4) = follow PMIC awake state
-
-- qcom,vs-soft-start-strength:
-	Usage: optional
-	Value type: <u32>
-	Description: This property sets the soft start strength for voltage
-		     switch type regulators; supported values are:
-			0 = 0.05 uA
-			1 = 0.25 uA
-			2 = 0.55 uA
-			3 = 0.75 uA
-
-- qcom,saw-slave:
-	Usage: optional
-	Value type: <boo>
-	Description: SAW controlled gang slave. Will not be configured.
-
-- qcom,saw-leader:
-	Usage: optional
-	Value type: <boo>
-	Description: SAW controlled gang leader. Will be configured as
-		     SAW regulator.
-
-Example:
-
-	regulators {
-		compatible = "qcom,pm8941-regulators";
-		vdd_l1_l3-supply = <&s1>;
-
-		s1: s1 {
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1400000>;
-		};
-
-		...
-
-		l1: l1 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		....
-	};
-
-Example 2:
-
-	saw3: syscon@9A10000 {
-		compatible = "syscon";
-		reg = <0x9A10000 0x1000>;
-	};
-
-	...
-
-	spm-regulators {
-		compatible = "qcom,pm8994-regulators";
-		qcom,saw-reg = <&saw3>;
-		s8 {
-			qcom,saw-slave;
-		};
-		s9 {
-			qcom,saw-slave;
-		};
-		s10 {
-			qcom,saw-slave;
-		};
-		pm8994_s11_saw: s11 {
-			qcom,saw-leader;
-			regulator-always-on;
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <1140000>;
-		};
-	};

337 lines not on this page · raw message

index 2ca690e70eb2..81fcaba84fed 100644
@@ -23,6 +23,7 @@ properties:
       - qcom,pm8950-regulators
       - qcom,pm8994-regulators
       - qcom,pmi8994-regulators
+      - qcom,pmp8074-regulators
       - qcom,pms405-regulators
 
   qcom,saw-reg:

@@ -276,6 +277,21 @@ allOf:
         vdd_l1-supply: true
       patternProperties:
         "^vdd_s[1-3]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pmp8074-regulators
+    then:
+      properties:
+        vdd_l10_l11_l12_l13-supply: true
+        vdd_l1_l2-supply: true
+        vdd_l3_l8-supply: true
+        vdd_l5_l6_l15-supply: true
+      patternProperties:
+        "^vdd_l[479]-supply$": true
+        "^vdd_s[1-5]-supply$": true
   - if:
       properties:
         compatible:

new file mode 100644
index 000000000000..7b3c9fe705aa
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@1 {
+		compatible = "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+
+		regulators {
+			compatible = "qcom,pmp8074-regulators";
+
+			s3: s3 {
+				regulator-name = "vdd_s3";
+				regulator-min-microvolt = <592000>;
+				regulator-max-microvolt = <1064000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			s4: s4 {
+				regulator-name = "vdd_s4";
+				regulator-min-microvolt = <712000>;
+				regulator-max-microvolt = <992000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			l11: l11 {
+				regulator-name = "l11";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+};

index b5e1eaa367bf..457cf83a1ed5 100644
@@ -3,6 +3,7 @@
 /* Copyright (c) 2017, The Linux Foundation. All rights reserved.
  */
 #include "ipq8074.dtsi"
+#include "pmp8074.dtsi"
 
 / {
 	#address-cells = <0x2>;

@@ -87,6 +88,7 @@ nand@0 {
 
 &sdhc_1 {
 	status = "okay";
+	vqmmc-supply = <&l11>;
 };
 
 &qusb_phy_0 {