dt-bindings: regulator: qcom,spmi-regulator: Convert to dtschema

new file mode 100644
index 000000000000..f7da310f1845
@@ -0,0 +1,176 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SPMI Regulators
+
+maintainers:
+  - Robert Marko <[email protected]>
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm660-regulators
+      - qcom,pm660l-regulators
+      - qcom,pm8004-regulators
+      - qcom,pm8005-regulators
+      - qcom,pm8226-regulators
+      - qcom,pm8841-regulators
+      - qcom,pm8916-regulators
+      - qcom,pm8941-regulators
+      - qcom,pm8950-regulators
+      - qcom,pm8994-regulators
+      - qcom,pmi8994-regulators
+      - qcom,pms405-regulators
+
+  qcom,saw-reg:
+    description: Reference to syscon node defining the SAW registers
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8941-regulators
+    then:
+      properties:
+        interrupts:
+          items:
+            - description: Over-current protection interrupt for 5V S1
+            - description: Over-current protection interrupt for 5V S2
+        interrupt-names:
+          items:
+            - const: ocp-5vs1
+            - const: ocp-5vs2
+
+patternProperties:
+  ".*-supply$":
+    description: Input supply phandle(s) for this node
+    $ref: "/schemas/types.yaml#/definitions/phandle"
+
+  "^((s|l|lvs|5vs)[0-9]*)$":
+    description: List of regulators and its properties
+    $ref: regulator.yaml#
+
+    properties:
+      qcom,ocp-max-retries:
+        description:
+          Maximum number of times to try toggling a voltage switch off and
+          back on as a result of consecutive over current events
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+
+      qcom,ocp-retry-delay:
+        description:
+          Time to delay in milliseconds between each voltage switch toggle
+          after an over current event takes place
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+
+      qcom,pin-ctrl-enable:
+        description:
+          Bit mask specifying which hardware pins should be used to enable the
+          regulator, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 15
+
+      qcom,pin-ctrl-hpm:
+        description:
+          Bit mask specifying which hardware pins should be used to force the
+          regulator into high power mode, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+          BIT(4) = follow PMIC awake state
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 31
+
+      qcom,vs-soft-start-strength:
+        description:
+          This property sets the soft start strength for voltage switch type
+          regulators.
+          Supported values are
+          0 = 0.05 uA
+          1 = 0.25 uA
+          2 = 0.55 uA
+          3 = 0.75 uA
+        $ref: "/schemas/types.yaml#/definitions/uint32"
+        minimum: 0
+        maximum: 3
+
+      qcom,saw-slave:
+        description: SAW controlled gang slave. Will not be configured.
+        type: boolean
+
+      qcom,saw-leader:
+        description:
+          SAW controlled gang leader. Will be configured as SAW regulator.
+        type: boolean
+
+      unevaluatedProperties: false
+
+unevaluatedProperties: false
+
+required:
+  - compatible
+
+examples:
+  - |
+    regulators {
+      compatible = "qcom,pm8941-regulators";
+      vdd_l1_l3-supply = <&s1>;
+
+      s1: s1 {
+        regulator-min-microvolt = <1300000>;
+        regulator-max-microvolt = <1400000>;
+      };
+
+      l1: l1 {
+        regulator-min-microvolt = <1225000>;
+        regulator-max-microvolt = <1300000>;
+      };
+    };
+
+  - |
+    saw3: syscon@9a10000 {
+      compatible = "syscon";
+      reg = <0x9a10000 0x1000>;
+    };
+
+    regulators {
+      compatible = "qcom,pm8994-regulators";
+      qcom,saw-reg = <&saw3>;
+
+      s8 {
+        qcom,saw-slave;
+      };
+
+      s9 {
+        qcom,saw-slave;
+      };
+
+      s10 {
+        qcom,saw-slave;
+      };
+
+      pm8994_s11_saw: s11 {
+        qcom,saw-leader;
+        regulator-always-on;
+        regulator-min-microvolt = <900000>;
+        regulator-max-microvolt = <1140000>;
+      };
+    };
+...

index f7da310f1845..960e61661bc8 100644
@@ -23,6 +23,7 @@ properties:
       - qcom,pm8950-regulators
       - qcom,pm8994-regulators
       - qcom,pmi8994-regulators
+      - qcom,pmp8074-regulators
       - qcom,pms405-regulators
 
   qcom,saw-reg:

index dbe23793e4d9..906468ee990e 100644
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-ipq8074.h>
+#include <dt-bindings/spmi/spmi.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ8074";

@@ -421,6 +422,39 @@ spmi_bus: spmi@200f000 {
 			interrupt-controller;
 			#interrupt-cells = <4>;
 			cell-index = <0>;
+
+			pmic@1 {
+				compatible ="qcom,spmi-pmic";
+				reg = <0x1 SPMI_USID>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				regulators {
+					compatible = "qcom,pmp8074-regulators";
+
+					s3: s3 {
+						regulator-name = "vdd_s3";
+						regulator-min-microvolt = <592000>;
+						regulator-max-microvolt = <1064000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					s4: s4 {
+						regulator-name = "vdd_s4";
+						regulator-min-microvolt = <712000>;
+						regulator-max-microvolt = <992000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					l11: l11 {
+						regulator-name = "l11";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <3300000>;
+					};
+				};
+			};
 		};
 
 		sdhc_1: sdhci@7824900 {

index 906468ee990e..2e8765aa8f37 100644
@@ -476,6 +476,8 @@ sdhc_1: sdhci@7824900 {
 			mmc-hs400-1_8v;
 			bus-width = <8>;
 
+			vqmmc-supply = <&l11>;
+
 			status = "disabled";
 		};