Skip to contentSkip to conversation

arm: rockchip: add support for the radxa rock3 board

PATCH In review Michael Riesch 2 participants 5 messages May 31, 2022 – Jun 8, 2022

Subsystems (5)
lore
Share & tools
lore
#0 lore raw

cover arm: rockchip: add support for the radxa rock3 board

Hi all,

This series aims to add support for the Radxa ROCK3 Model A single board computer featuring the Rockchip RK3568 SoC.

The first two patches mock the dts sync from the Linux kernel and introduce the device tree for the board (will appear in Linux v5.19-rc1). These patches can be dropped of course and are added only for convenience.

There are a few open issues that are somewhat shared by all RK356x boards:

- The RAM size is defined in the device tree and limited to 2 GB. This is correct for the 2 GB version lying around on my desk, but it should be noted that there are also 4 GB and 8 GB versions of this board available.

- The eMMC controller seems to require the "no-sd" property in the device tree, which is not present in the mainline version. The quick fix is to provide this property in the barebox dts.

- RFC: The "rk3568_start" method in the low-level board code seems to be shared by all RK356x boards. Can it be refactored and made non-static? If yes, what would be a reasonable location for the new function?

- Of course the IO domain bits are board specific. In the long run they should be replaced anyway by a proper iodomain driver. For the time being I believe they could remain in the ENTRY_FUNCTION.

Apart from these issues (which are not exactly critical) barebox works just fine on this neat little board.

Looking forward to your comments!

Best regards,
Michael

Michael Riesch (3):
HACK: add device trees for rk3568
HACK: add device tree for radxa rock3 model a
arm: rockchip: add support for the radxa rock3 board

 Documentation/boards/rockchip.rst         |   1 +
 arch/arm/boards/Makefile                  |   1 +
 arch/arm/boards/radxa-rock3/.gitignore    |   1 +
 arch/arm/boards/radxa-rock3/Makefile      |   3 +
 arch/arm/boards/radxa-rock3/board.c       |  48 ++
 arch/arm/boards/radxa-rock3/lowlevel.c    |  44 ++
 arch/arm/configs/rockchip_v8_defconfig    |   1 +
 arch/arm/dts/Makefile                     |   1 +
 arch/arm/dts/rk3568-rock-3a.dts           |  54 +++
 arch/arm/mach-rockchip/Kconfig            |   6 +
 dts/src/arm64/rockchip/rk3568-rock-3a.dts | 562 ++++++++++++++++++++++
 dts/src/arm64/rockchip/rk3568.dtsi        |  23 +
 dts/src/arm64/rockchip/rk356x.dtsi        |  74 ++-
 images/Makefile.rockchip                  |   7 +
 14 files changed, 825 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm/boards/radxa-rock3/.gitignore
 create mode 100644 arch/arm/boards/radxa-rock3/Makefile
 create mode 100644 arch/arm/boards/radxa-rock3/board.c
 create mode 100644 arch/arm/boards/radxa-rock3/lowlevel.c
 create mode 100644 arch/arm/dts/rk3568-rock-3a.dts
 create mode 100644 dts/src/arm64/rockchip/rk3568-rock-3a.dts
Signature · 7 lines
2.30.2


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#1 lore raw

PATCH 1/3 HACK: add device trees for rk3568

Mock sync from Linux v5.19-rc1.

---
 dts/src/arm64/rockchip/rk3568.dtsi | 23 ++++++++++
 dts/src/arm64/rockchip/rk356x.dtsi | 74 +++++++++++++++++++++++++++++-
 2 files changed, 96 insertions(+), 1 deletion(-)
dts/src/arm64/rockchip/rk3568.dtsi +23 -0
index 5b0f528d68..5eafddf62e 100644
@@ -8,6 +8,20 @@
 / {
 	compatible = "rockchip,rk3568";
 
+	sata0: sata@fc000000 {
+		compatible = "rockchip,rk3568-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfc000000 0 0x1000>;
+		clocks = <&cru ACLK_SATA0>, <&cru CLK_SATA0_PMALIVE>,
+			 <&cru CLK_SATA0_RXOOB>;
+		clock-names = "sata", "pmalive", "rxoob";
+		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+		phys = <&combphy0 PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		ports-implemented = <0x1>;
+		power-domains = <&power RK3568_PD_PIPE>;
+		status = "disabled";
+	};
+
 	pipe_phy_grf0: syscon@fdc70000 {
 		compatible = "rockchip,rk3568-pipe-phy-grf", "syscon";
 		reg = <0x0 0xfdc70000 0x0 0x1000>;
@@ -99,6 +113,10 @@
 	};
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -114,3 +132,8 @@
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+};
dts/src/arm64/rockchip/rk356x.dtsi +73 -1

92 lines not on this page · raw message

Signature · 7 lines
2.30.2


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#2 lore raw

PATCH 2/3 HACK: add device tree for radxa rock3 model a

In reply to Michael Riesch

Mock sync from Linux v5.19-rc1.

---
 dts/src/arm64/rockchip/rk3568-rock-3a.dts | 562 ++++++++++++++++++++++
 1 file changed, 562 insertions(+)
 create mode 100644 dts/src/arm64/rockchip/rk3568-rock-3a.dts
dts/src/arm64/rockchip/rk3568-rock-3a.dts new file +562 -0
new file mode 100644
index 0000000000..0813c0c5ab
@@ -0,0 +1,562 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3568.dtsi"
+
+/ {
+	model = "Radxa ROCK3 Model A";
+	compatible = "radxa,rock3a", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_user: led-0 {
+			gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_user_en>;
+		};
+	};
+
+	rk809-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	vcc12v_dcin: vcc12v-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb: vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb_host: vcc5v0-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_hub: vcc5v0-usb-hub-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_hub_en>;
+		regulator-name = "vcc5v0_usb_hub";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+};
+
+&combphy0 {
+	status = "okay";
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+
+		codec {
+			mic-in-differential;
+		};
+	};
+};
+
+&i2s1_8ch {
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_rst>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	ethernet {
+		eth_phy_rst: eth_phy_rst {
+			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		led_user_en: led_user_en {
+			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_hub_en: vcc5v0_usb_hub_en {
+			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	vbus-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
Signature · 7 lines
2.30.2


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#3 lore raw

PATCH 3/3 arm: rockchip: add support for the radxa rock3 board

In reply to Michael Riesch

Add basic support for the Radxa ROCK3 Model A board (featuring the Rockchip RK3568 SoC).

---
 Documentation/boards/rockchip.rst      |  1 +
 arch/arm/boards/Makefile               |  1 +
 arch/arm/boards/radxa-rock3/.gitignore |  1 +
 arch/arm/boards/radxa-rock3/Makefile   |  3 ++
 arch/arm/boards/radxa-rock3/board.c    | 48 +++++++++++++++++++++++
 arch/arm/boards/radxa-rock3/lowlevel.c | 44 +++++++++++++++++++++
 arch/arm/configs/rockchip_v8_defconfig |  1 +
 arch/arm/dts/Makefile                  |  1 +
 arch/arm/dts/rk3568-rock-3a.dts        | 54 ++++++++++++++++++++++++++
 arch/arm/mach-rockchip/Kconfig         |  6 +++
 images/Makefile.rockchip               |  7 ++++
 11 files changed, 167 insertions(+)
 create mode 100644 arch/arm/boards/radxa-rock3/.gitignore
 create mode 100644 arch/arm/boards/radxa-rock3/Makefile
 create mode 100644 arch/arm/boards/radxa-rock3/board.c
 create mode 100644 arch/arm/boards/radxa-rock3/lowlevel.c
 create mode 100644 arch/arm/dts/rk3568-rock-3a.dts
Documentation/boards/rockchip.rst +1 -0
index 041bb9fa64..d4f8a9c5a3 100644
@@ -59,6 +59,7 @@ Supported Boards
 - Rockchip RK3568 EVB
 - Rockchip RK3568 Bananapi R2 Pro
 - Pine64 Quartz64 Model A
+- Radxa ROCK3 Model A
 
 The steps described in the following target the RK3568 and the RK3568 EVB but
 generally apply to both SoCs and all boards.
arch/arm/boards/Makefile +1 -0
index d303999614..3ccde26f1b 100644
@@ -192,3 +192,4 @@ obj-$(CONFIG_MACH_SKOV_ARM9CPU)			+= skov-arm9cpu/
 obj-$(CONFIG_MACH_RK3568_EVB)			+= rockchip-rk3568-evb/
 obj-$(CONFIG_MACH_RK3568_BPI_R2PRO)			+= rockchip-rk3568-bpi-r2pro/
 obj-$(CONFIG_MACH_PINE64_QUARTZ64)		+= pine64-quartz64/
+obj-$(CONFIG_MACH_RADXA_ROCK3)			+= radxa-rock3/
arch/arm/boards/radxa-rock3/.gitignore new file +1 -0
new file mode 100644
index 0000000000..f458f794b5
@@ -0,0 +1 @@
+sdram-init.bin
arch/arm/boards/radxa-rock3/Makefile new file +3 -0
new file mode 100644
index 0000000000..b37b6c870b
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y += board.o
+lwl-y += lowlevel.o
arch/arm/boards/radxa-rock3/board.c new file +48 -0

48 lines not on this page · raw message

arch/arm/boards/radxa-rock3/lowlevel.c new file +44 -0

44 lines not on this page · raw message

arch/arm/configs/rockchip_v8_defconfig +1 -0
index 79d51234cc..1c7116e74a 100644
@@ -2,6 +2,7 @@ CONFIG_ARCH_ROCKCHIP=y
 CONFIG_MACH_RK3568_EVB=y
 CONFIG_MACH_RK3568_BPI_R2PRO=y
 CONFIG_MACH_PINE64_QUARTZ64=y
+CONFIG_MACH_RADXA_ROCK3=y
 CONFIG_BOARD_ARM_GENERIC_DT=y
 CONFIG_ARM_OPTIMZED_STRING_FUNCTIONS=y
 CONFIG_ARM_PSCI_CLIENT=y
arch/arm/dts/Makefile +1 -0
index d67d10bde8..723bd2a123 100644
@@ -105,6 +105,7 @@ lwl-$(CONFIG_MACH_PROTONIC_STM32MP1) += \
 	stm32mp151-prtt1c.dtb.o \
 	stm32mp151-prtt1s.dtb.o
 lwl-$(CONFIG_MACH_RADXA_ROCK) += rk3188-radxarock.dtb.o
+lwl-$(CONFIG_MACH_RADXA_ROCK3) += rk3568-rock-3a.dtb.o
 lwl-$(CONFIG_MACH_PHYTEC_SOM_RK3288) += rk3288-phycore-som.dtb.o
 lwl-$(CONFIG_MACH_REALQ7) += imx6q-dmo-edmqmx6.dtb.o
 lwl-$(CONFIG_MACH_RK3568_EVB) += rk3568-evb1-v10.dtb.o
arch/arm/dts/rk3568-rock-3a.dts new file +54 -0

54 lines not on this page · raw message

arch/arm/mach-rockchip/Kconfig +6 -0
index ffd3aa8a4e..4b6dfd2c17 100644
@@ -80,6 +80,12 @@ config MACH_PINE64_QUARTZ64
 	help
 	  Say Y here if you are using a Pine64 Quartz64
 
+config MACH_RADXA_ROCK3
+       select ARCH_RK3568
+       bool "Radxa ROCK3"
+       help
+	  Say Y here if you are using a Radxa ROCK3
+
 comment "select board features:"
 
 config ARCH_RK3399_OPTEE
images/Makefile.rockchip +7 -0
index cdc7772c2e..33c76caf79 100644
@@ -20,6 +20,9 @@ image-$(CONFIG_MACH_RK3568_BPI_R2PRO) += barebox-rk3568-bpi-r2pro.img
 pblb-$(CONFIG_MACH_PINE64_QUARTZ64) += start_quartz64a
 image-$(CONFIG_MACH_PINE64_QUARTZ64) += barebox-quartz64a.img
 
+pblb-$(CONFIG_MACH_RADXA_ROCK3) += start_rock3a
+image-$(CONFIG_MACH_RADXA_ROCK3) += barebox-rock3a.img
+
 quiet_cmd_rkimg_image = RK-IMG $@
       cmd_rkimg_image = $(objtree)/scripts/rkimage -o $@ $(word 2,$^) $(word 1,$^)
 
@@ -34,3 +37,7 @@ $(obj)/barebox-rk3568-bpi-r2pro.img: $(obj)/start_rk3568_bpi_r2pro.pblb \
 $(obj)/barebox-quartz64a.img: $(obj)/start_quartz64a.pblb \
                 $(board)/pine64-quartz64/sdram-init.bin
 	$(call if_changed,rkimg_image)
+
+$(obj)/barebox-rock3a.img: $(obj)/start_rock3a.pblb \
+                $(board)/radxa-rock3/sdram-init.bin
+	$(call if_changed,rkimg_image)
Signature · 7 lines
2.30.2


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#4 lore raw
In reply to Michael Riesch
Quoted 9 lines · Michael Riesch

Hi all,

This series aims to add support for the Radxa ROCK3 Model A single board computer featuring the Rockchip RK3568 SoC.

The first two patches mock the dts sync from the Linux kernel and introduce the device tree for the board (will appear in Linux v5.19-rc1). These patches can be dropped of course and are added only for convenience.

devicetree-rebasing for v5.19-rc1 is out, I applied this series now.

Sascha

Signature · 9 lines
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox