dt-bindings: efm32: remove bindings for deleted platform
Subsystems (6)
PATCH 1/1 dt-bindings: efm32: remove bindings for deleted platform
Commit cc6111375cec ("ARM: drop efm32 platform") removed the platform, so no need to still carry the bindings.
--- .../devicetree/bindings/clock/efm32-clock.txt | 11 ----- .../devicetree/bindings/i2c/i2c-efm32.txt | 33 -------------- .../devicetree/bindings/serial/efm32-uart.txt | 20 --------- .../devicetree/bindings/spi/efm32-spi.txt | 39 ----------------- include/dt-bindings/clock/efm32-cmu.h | 43 ------------------- 5 files changed, 146 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/efm32-clock.txt delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-efm32.txt delete mode 100644 Documentation/devicetree/bindings/serial/efm32-uart.txt delete mode 100644 Documentation/devicetree/bindings/spi/efm32-spi.txt delete mode 100644 include/dt-bindings/clock/efm32-cmu.h
Documentation/devicetree/bindings/clock/efm32-clock.txt deleted +0 -11
@@ -1,11 +0,0 @@ -* Clock bindings for Energy Micro efm32 Giant Gecko's Clock Management Unit - -Required properties: -- compatible: Should be "efm32gg,cmu" -- reg: Base address and length of the register set -- interrupts: Interrupt used by the CMU -- #clock-cells: Should be <1> - -The clock consumer should specify the desired clock by having the clock ID in -its "clocks" phandle cell. The header efm32-clk.h contains a list of available -IDs.
Documentation/devicetree/bindings/i2c/i2c-efm32.txt deleted +0 -33
@@ -1,33 +0,0 @@ -* Energymicro efm32 i2c controller - -Required properties : - - - reg : Offset and length of the register set for the device - - compatible : should be "energymicro,efm32-i2c" - - interrupts : the interrupt number - - clocks : reference to the module clock - -Recommended properties : - - - clock-frequency : maximal I2C bus clock frequency in Hz. - - energymicro,location : Decides the location of the USART I/O pins. - Allowed range : [0 .. 6] - -Example: - i2c0: i2c@4000a000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "energymicro,efm32-i2c"; - reg = <0x4000a000 0x400>; - interrupts = <9>; - clocks = <&cmu clk_HFPERCLKI2C0>; - clock-frequency = <100000>; - energymicro,location = <3>; - - eeprom@50 { - compatible = "microchip,24c02"; - reg = <0x50>; - pagesize = <16>; - }; - }; -
Documentation/devicetree/bindings/serial/efm32-uart.txt deleted +0 -20
@@ -1,20 +0,0 @@ -* Energymicro efm32 UART - -Required properties: -- compatible : Should be "energymicro,efm32-uart" -- reg : Address and length of the register set -- interrupts : Should contain uart interrupt - -Optional properties: -- energymicro,location : Decides the location of the USART I/O pins. - Allowed range : [0 .. 5] - Default: 0 - -Example: - -uart@4000c400 { - compatible = "energymicro,efm32-uart"; - reg = <0x4000c400 0x400>; - interrupts = <15>; - energymicro,location = <0>; -};
Documentation/devicetree/bindings/spi/efm32-spi.txt deleted +0 -39
@@ -1,39 +0,0 @@ -* Energy Micro EFM32 SPI - -Required properties: -- #address-cells: see spi-bus.txt -- #size-cells: see spi-bus.txt -- compatible: should be "energymicro,efm32-spi" -- reg: Offset and length of the register set for the controller -- interrupts: pair specifying rx and tx irq -- clocks: phandle to the spi clock -- cs-gpios: see spi-bus.txt - -Recommended properties : -- energymicro,location: Value to write to the ROUTE register's LOCATION - bitfield to configure the pinmux for the device, see - datasheet for values. - If this property is not provided, keeping what is - already configured in the hardware, so its either the - reset default 0 or whatever the bootloader did. - -Example: - -spi1: spi@4000c400 { /* USART1 */ - #address-cells = <1>; - #size-cells = <0>; - compatible = "energymicro,efm32-spi"; - reg = <0x4000c400 0x400>; - interrupts = <15 16>; - clocks = <&cmu 20>; - cs-gpios = <&gpio 51 1>; // D3 - energymicro,location = <1>; - - ks8851@0 { - compatible = "ks8851"; - spi-max-frequency = <6000000>; - reg = <0>; - interrupt-parent = <&boardfpga>; - interrupts = <4>; - }; -};
include/dt-bindings/clock/efm32-cmu.h deleted +0 -43
43 lines not on this page · raw message
Signature · 1 line
2.35.1
Quoting Wolfram Sang (2022-06-15 14:07:19)
Quoted 5 lines
Commit
cc6111375cec("ARM: drop efm32 platform") removed the platform, so no need to still carry the bindings.Signed-off-by Wolfram Sang <[email protected]>---
Quoted 2 lines · Wolfram Sang
Commit
cc6111375cec("ARM: drop efm32 platform") removed the platform, so no need to still carry the bindings.
Rob Herring
maintainerQuoted 4 lines · Wolfram Sang
Commit
cc6111375cec("ARM: drop efm32 platform") removed the platform, so no need to still carry the bindings.Signed-off-by Wolfram Sang <[email protected]>
Quoted 13 lines
--- .../devicetree/bindings/clock/efm32-clock.txt | 11 ----- .../devicetree/bindings/i2c/i2c-efm32.txt | 33 -------------- .../devicetree/bindings/serial/efm32-uart.txt | 20 --------- .../devicetree/bindings/spi/efm32-spi.txt | 39 ----------------- include/dt-bindings/clock/efm32-cmu.h | 43 ------------------- 5 files changed, 146 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/efm32-clock.txt delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-efm32.txt delete mode 100644 Documentation/devicetree/bindings/serial/efm32-uart.txt delete mode 100644 Documentation/devicetree/bindings/spi/efm32-spi.txt delete mode 100644 include/dt-bindings/clock/efm32-cmu.h
Deletions are automatically applied, thanks! ;)
Quoted 4 lines · Wolfram Sang
Commit
cc6111375cec("ARM: drop efm32 platform") removed the platform, so no need to still carry the bindings.Signed-off-by Wolfram Sang <[email protected]>
Quoted 12 lines
--- .../devicetree/bindings/clock/efm32-clock.txt | 11 ----- .../devicetree/bindings/i2c/i2c-efm32.txt | 33 -------------- .../devicetree/bindings/serial/efm32-uart.txt | 20 --------- .../devicetree/bindings/spi/efm32-spi.txt | 39 ----------------- include/dt-bindings/clock/efm32-cmu.h | 43 ------------------- 5 files changed, 146 deletions(-) delete mode 100644 Documentation/devicetree/bindings/clock/efm32-clock.txt delete mode 100644 Documentation/devicetree/bindings/i2c/i2c-efm32.txt delete mode 100644 Documentation/devicetree/bindings/serial/efm32-uart.txt delete mode 100644 Documentation/devicetree/bindings/spi/efm32-spi.txt delete mode 100644 include/dt-bindings/clock/efm32-cmu.h
I didn't do that back then wondering if the bindings are sensible to keep even for removed arch (or more general drivers). In this case the chip isn't old and unavailable, but just too small for sensible Linux usage.
OTOH I'm not aware of any dtb usage on efm32.
No hard feelings here, if you consider it not useful to keep the binding around, go on and remove them.
Best regards
Uwe
Signature · 2 lines
Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | https://www.pengutronix.de/ |