USB: serial: option: add Quectel RM500K module support
Subsystems (4)
PATCH 1/1 USB: serial: option: add Quectel RM500K module support
Add usb product id of the Quectel RM500K module.
RM500K provides 2 maindatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.
The following kernel settings is required for RM500K.
- CONFIG_USB_SERIAL_GENERIC
- CONFIG_USB_SERIAL_CONSOLE
- CONFIG_USB_NET_RNDIS_HOST
- CONFIG_USB_SERIAL_WWAN
- CONFIG_USB_SERIAL_OPTION
usb-devices output for 0x7001:
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=7001 Rev=00.01 S: Manufacturer=MediaTek Inc. S: Product=USB DATA CARD S: SerialNumber=869206050009672 C: #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
--- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/usb/serial/option.c +2 -0
@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);#define QUECTEL_PRODUCT_BG96 0x0296#define QUECTEL_PRODUCT_EP06 0x0306#define QUECTEL_PRODUCT_EM12 0x0512 +#define QUECTEL_PRODUCT_RM500K 0x7001#define QUECTEL_PRODUCT_RM500Q 0x0800#define QUECTEL_PRODUCT_EC200S_CN 0x6002#define QUECTEL_PRODUCT_EC200T 0x6026
@@ -1135,6 +1136,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) }, { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */ .driver_info = RSVD(3) | ZLP }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),
Signature · 1 line
2.18.0
Johan Hovold
maintainerQuoted 3 lines · Macpaul Lin
Add usb product id of the Quectel RM500K module.
RM500K provides 2 maindatory interfaces to Linux host after enumeration.
typo: mandatory
Quoted 10 lines
-
/dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.The following kernel settings is required for RM500K.
-CONFIG_USB_SERIAL_GENERIC
-CONFIG_USB_SERIAL_CONSOLE
You shouldn't need either of those.
Quoted 3 lines
-
CONFIG_USB_NET_RNDIS_HOST
-CONFIG_USB_SERIAL_WWAN
-CONFIG_USB_SERIAL_OPTION
And OPTION selects WWAN so no need to mention that.
But you can probably just drop this paragraph.
Quoted 29 lines
usb-devices output for
0x7001:T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=7001 Rev=00.01 S: Manufacturer=MediaTek Inc. S: Product=USB DATA CARD S: SerialNumber=869206050009672 C: #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Quoted 8 lines
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Can you say something about what the other interfaces are for?
Quoted 2 lines
Signed-off-by Macpaul Lin <[email protected]>Signed-off-by Ballon Shi <[email protected]>
The submitters SoB always goes last (to reflect how the patch was forwarded).
If Ballon is the primary author you need to add a From line at the beginning of mail body.
Otherwise you should add a Co-developed-by tag before the co-author's SoB.
More details in
Documentation/process/submitting-patches.rst
Quoted 10 lines
--- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+)drivers/usb/serial/option.c +0
-0
drivers/usb/serial/option.c static void option_instat_callback(struct urb *urb); · line 256
Quoted 4 lines
drivers/usb/serial/option.c +1
-0@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);#define QUECTEL_PRODUCT_BG96 0x0296#define QUECTEL_PRODUCT_EP06 0x0306#define QUECTEL_PRODUCT_EM12 0x0512 +#define QUECTEL_PRODUCT_RM500K 0x7001
Please keep the defines sorted by PID here.
drivers/usb/serial/option.c static const struct usb_device_id option_ids[] = { · line 1142
Quoted 11 lines
drivers/usb/serial/option.c +1
-0#define QUECTEL_PRODUCT_RM500Q 0x0800#define QUECTEL_PRODUCT_EC200S_CN 0x6002#define QUECTEL_PRODUCT_EC200T 0x6026@@ -1135,6 +1136,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) }, { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */ .driver_info = RSVD(3) | ZLP }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),
Johan
Quoted 6 lines · Johan Hovold
Quoted 3 lines · Macpaul Lin
Add usb product id of the Quectel RM500K module.
RM500K provides 2 maindatory interfaces to Linux host after enumeration.
typo: mandatory
Will be fixed on patch v2.
Quoted 10 lines
Quoted 10 lines
-
/dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.The following kernel settings is required for RM500K.
-CONFIG_USB_SERIAL_GENERIC
-CONFIG_USB_SERIAL_CONSOLE
Double checked: no need confirmed.
Quoted 5 lines
You shouldn't need either of those.
Quoted 3 lines
-
CONFIG_USB_NET_RNDIS_HOST
-CONFIG_USB_SERIAL_WWAN
-CONFIG_USB_SERIAL_OPTION
Will remove this paragraph in patch v2.
Quoted 12 lines
And OPTION selects WWAN so no need to mention that.
But you can probably just drop this paragraph.
Quoted 8 lines
usb-devices output for
0x7001:T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=7001 Rev=00.01 S: Manufacturer=MediaTek Inc. S: Product=USB DATA CARD S: SerialNumber=869206050009672 C: #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
RDNIS interface, will be enumerated as ethX.
Quoted 5 lines
Quoted 5 lines
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
COM port.
Quoted 9 lines
Quoted 9 lines
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Debug interface (will be disabled with mass-production shipping).
Quoted 3 lines
Quoted 3 lines
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
COM port.
Quoted 13 lines
Quoted 4 lines
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=optionQuoted 8 lines
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Quoted 1 line
Can you say something about what the other interfaces are for?
The others COM ports are MODEM related interface but I'm not sure the exactly purpose and how they are used.
I'll summarize the part I know in patch v2.
Quoted 5 lines
Quoted 2 lines
Signed-off-by Macpaul Lin <[email protected]>Signed-off-by Ballon Shi <[email protected]>The submitters SoB always goes last (to reflect how the patch was forwarded).
Will be fixed in patch v2.
Quoted 2 lines
If Ballon is the primary author you need to add a From line at the beginning of mail body.
No need for this patch.
Quoted 7 lines
Otherwise you should add a Co-developed-by tag before the co-author's SoB.
More details in
Documentation/process/submitting-patches.rst
Will be fixed in patch v2.
Quoted 5 lines
Quoted 5 lines
--- drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+)
Quoted 11 lines
drivers/usb/serial/option.c static void option_instat_callback(struct urb *urb); · line 256
Quoted 9 lines
drivers/usb/serial/option.c +1
-0@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);#define QUECTEL_PRODUCT_BG96 0x0296#define QUECTEL_PRODUCT_EP06 0x0306#define QUECTEL_PRODUCT_EM12 0x0512 +#define QUECTEL_PRODUCT_RM500K 0x7001Please keep the defines sorted by PID here.
Will be fixed in patch v2.
Quoted 15 lines
drivers/usb/serial/option.c static const struct usb_device_id option_ids[] = { · line 1142
Quoted 12 lines
drivers/usb/serial/option.c +1
-0#define QUECTEL_PRODUCT_RM500Q 0x0800#define QUECTEL_PRODUCT_EC200S_CN 0x6002#define QUECTEL_PRODUCT_EC200T 0x6026@@ -1135,6 +1136,7 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) }, { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */ .driver_info = RSVD(3) | ZLP }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),Johan
Thanks for the quick review.
I'll fix them all and send patch v2.
Macpaul Lin
PATCH v2 1/1 USB: serial: option: add Quectel RM500K module support
In reply to Macpaul LinAdd usb product id of the Quectel RM500K module.
RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.
"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs
usb-devices output for 0x7001:
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=7001 Rev=00.01 S: Manufacturer=MediaTek Inc. S: Product=USB DATA CARD S: SerialNumber=869206050009672 C: #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none) E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
---
Change for v2:
- Update USB interfaces descriptions in the commit message.
- Fix typo, format and contributers in the commit message.
- Update PID definition in numeric order.
drivers/usb/serial/option.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/usb/serial/option.c +2 -0
@@ -256,6 +256,7 @@ static void option_instat_callback(struct urb *urb);#define QUECTEL_PRODUCT_RM500Q 0x0800#define QUECTEL_PRODUCT_EC200S_CN 0x6002#define QUECTEL_PRODUCT_EC200T 0x6026 +#define QUECTEL_PRODUCT_RM500K 0x7001#define CMOTECH_VENDOR_ID 0x16d8#define CMOTECH_PRODUCT_6001 0x6001
@@ -1147,6 +1148,7 @@ static const struct usb_device_id option_ids[] = { .driver_info = ZLP }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) }, { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) }, + { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) }, { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) }, { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
Signature · 1 line
2.18.0
Johan Hovold
maintainerQuoted 18 lines · Macpaul Lin
Add usb product id of the Quectel RM500K module.
RM500K provides 2 mandatory interfaces to Linux host after enumeration.
-/dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface."RNDIS": RNDIS + ADB + AT (
/dev/ttyUSB5) + MODEM COMsusb-devices output for
0x7001:Co-developed-by Ballon Shi <[email protected]>Signed-off-by Ballon Shi <[email protected]>Signed-off-by Macpaul Lin <[email protected]>
Quoted 5 lines
---
Change for v2:
- Update USB interfaces descriptions in the commit message.
- Fix typo, format and contributers in the commit message.
- Update PID definition in numeric order.
Thanks for the update. Now applied.
Johan