Skip to contentSkip to conversation

USB: serial: option: add Quectel RM500K module support

PATCH Superseded Macpaul Lin 2 participants 5 messages Jun 23, 2022

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 USB: serial: option: add Quectel RM500K module support

Add usb product id of the Quectel RM500K module.

RM500K provides 2 maindatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.

The following kernel settings is required for RM500K.
- CONFIG_USB_SERIAL_GENERIC
- CONFIG_USB_SERIAL_CONSOLE
- CONFIG_USB_NET_RNDIS_HOST
- CONFIG_USB_SERIAL_WWAN
- CONFIG_USB_SERIAL_OPTION

usb-devices output for 0x7001:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/usb/serial/option.c +2 -0
index e7755d9cfc61..e2587a3c7600 100644
@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);
 #define QUECTEL_PRODUCT_BG96			0x0296
 #define QUECTEL_PRODUCT_EP06			0x0306
 #define QUECTEL_PRODUCT_EM12			0x0512
+#define QUECTEL_PRODUCT_RM500K			0x7001
 #define QUECTEL_PRODUCT_RM500Q			0x0800
 #define QUECTEL_PRODUCT_EC200S_CN		0x6002
 #define QUECTEL_PRODUCT_EC200T			0x6026
@@ -1135,6 +1136,7 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) },
 	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */
 	  .driver_info = RSVD(3) | ZLP },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),
Signature · 1 line
2.18.0
maintainer
#1 lore raw
Quoted 3 lines · Macpaul Lin

Add usb product id of the Quectel RM500K module.

RM500K provides 2 maindatory interfaces to Linux host after enumeration.

typo: mandatory

Quoted 10 lines

- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.

The following kernel settings is required for RM500K.
- CONFIG_USB_SERIAL_GENERIC
- CONFIG_USB_SERIAL_CONSOLE

You shouldn't need either of those.

Quoted 3 lines

- CONFIG_USB_NET_RNDIS_HOST
- CONFIG_USB_SERIAL_WWAN
- CONFIG_USB_SERIAL_OPTION

And OPTION selects WWAN so no need to mention that.

But you can probably just drop this paragraph.

Quoted 29 lines

usb-devices output for 0x7001:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Quoted 8 lines
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Can you say something about what the other interfaces are for?

Quoted 2 lines

The submitters SoB always goes last (to reflect how the patch was forwarded).

If Ballon is the primary author you need to add a From line at the beginning of mail body.

Otherwise you should add a Co-developed-by tag before the co-author's SoB.

More details in

Documentation/process/submitting-patches.rst

Quoted 10 lines
---
 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/usb/serial/option.c +0 -0
index e7755d9cfc61..e2587a3c7600 100644

drivers/usb/serial/option.c static void option_instat_callback(struct urb *urb); · line 256

Quoted 4 lines
drivers/usb/serial/option.c +1 -0
@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);
 #define QUECTEL_PRODUCT_BG96			0x0296
 #define QUECTEL_PRODUCT_EP06			0x0306
 #define QUECTEL_PRODUCT_EM12			0x0512
+#define QUECTEL_PRODUCT_RM500K			0x7001

Please keep the defines sorted by PID here.

drivers/usb/serial/option.c static const struct usb_device_id option_ids[] = { · line 1142

Quoted 11 lines
drivers/usb/serial/option.c +1 -0
 #define QUECTEL_PRODUCT_RM500Q			0x0800
 #define QUECTEL_PRODUCT_EC200S_CN		0x6002
 #define QUECTEL_PRODUCT_EC200T			0x6026
@@ -1135,6 +1136,7 @@ static const struct usb_device_id option_ids[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) },
 	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */
 	  .driver_info = RSVD(3) | ZLP },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),

Johan

#2 lore raw
Quoted 6 lines · Johan Hovold
Quoted 3 lines · Macpaul Lin

Add usb product id of the Quectel RM500K module.

RM500K provides 2 maindatory interfaces to Linux host after enumeration.

typo: mandatory

Will be fixed on patch v2.

Quoted 10 lines
Quoted 10 lines

- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.

The following kernel settings is required for RM500K.
- CONFIG_USB_SERIAL_GENERIC
- CONFIG_USB_SERIAL_CONSOLE

Double checked: no need confirmed.

Quoted 5 lines

You shouldn't need either of those.

Quoted 3 lines

- CONFIG_USB_NET_RNDIS_HOST
- CONFIG_USB_SERIAL_WWAN
- CONFIG_USB_SERIAL_OPTION

Will remove this paragraph in patch v2.

Quoted 12 lines

And OPTION selects WWAN so no need to mention that.

But you can probably just drop this paragraph.

Quoted 8 lines

usb-devices output for 0x7001:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA

RDNIS interface, will be enumerated as ethX.

Quoted 5 lines
Quoted 5 lines
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

COM port.

Quoted 9 lines
Quoted 9 lines
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Debug interface (will be disabled with mass-production shipping).

Quoted 3 lines
Quoted 3 lines
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

COM port.

Quoted 13 lines
Quoted 4 lines
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
Quoted 8 lines
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Quoted 1 line

Can you say something about what the other interfaces are for?

The others COM ports are MODEM related interface but I'm not sure the exactly purpose and how they are used.

I'll summarize the part I know in patch v2.

Quoted 5 lines
Quoted 2 lines

The submitters SoB always goes last (to reflect how the patch was forwarded).

Will be fixed in patch v2.

Quoted 2 lines

If Ballon is the primary author you need to add a From line at the beginning of mail body.

No need for this patch.

Quoted 7 lines

Otherwise you should add a Co-developed-by tag before the co-author's SoB.

More details in

Documentation/process/submitting-patches.rst

Will be fixed in patch v2.

Quoted 5 lines
Quoted 5 lines
---
  drivers/usb/serial/option.c | 2 ++
  1 file changed, 2 insertions(+)
Quoted 11 lines

drivers/usb/serial/option.c static void option_instat_callback(struct urb *urb); · line 256

Quoted 9 lines
drivers/usb/serial/option.c +1 -0
index e7755d9cfc61..e2587a3c7600 100644
@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);
  #define QUECTEL_PRODUCT_BG96			0x0296
  #define QUECTEL_PRODUCT_EP06			0x0306
  #define QUECTEL_PRODUCT_EM12			0x0512
+#define QUECTEL_PRODUCT_RM500K			0x7001

Please keep the defines sorted by PID here.

Will be fixed in patch v2.

Quoted 15 lines

drivers/usb/serial/option.c static const struct usb_device_id option_ids[] = { · line 1142

Quoted 12 lines
drivers/usb/serial/option.c +1 -0
  #define QUECTEL_PRODUCT_RM500Q			0x0800
  #define QUECTEL_PRODUCT_EC200S_CN		0x6002
  #define QUECTEL_PRODUCT_EC200T			0x6026
@@ -1135,6 +1136,7 @@ static const struct usb_device_id option_ids[] = {
  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, 0x0620, 0xff, 0, 0) },
  	{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x0700, 0xff), /* BG95 */
  	  .driver_info = RSVD(3) | ZLP },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) },
  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x30) },
  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0, 0) },
  	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500Q, 0xff, 0xff, 0x10),

Johan

Thanks for the quick review.
I'll fix them all and send patch v2.

Macpaul Lin

#3 lore raw

PATCH v2 1/1 USB: serial: option: add Quectel RM500K module support

In reply to Macpaul Lin

Add usb product id of the Quectel RM500K module.

RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.

"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs

usb-devices output for 0x7001:

T:  Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=7001 Rev=00.01
S:  Manufacturer=MediaTek Inc.
S:  Product=USB DATA CARD
S:  SerialNumber=869206050009672
C:  #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E:  Ad=82(I) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms

---
Change for v2:
- Update USB interfaces descriptions in the commit message.
- Fix typo, format and contributers in the commit message.
- Update PID definition in numeric order.

 drivers/usb/serial/option.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/usb/serial/option.c +2 -0
index ed1e50d83cca..5b94519c790b 100644
@@ -256,6 +256,7 @@ static void option_instat_callback(struct urb *urb);
 #define QUECTEL_PRODUCT_RM500Q			0x0800
 #define QUECTEL_PRODUCT_EC200S_CN		0x6002
 #define QUECTEL_PRODUCT_EC200T			0x6026
+#define QUECTEL_PRODUCT_RM500K			0x7001
 
 #define CMOTECH_VENDOR_ID			0x16d8
 #define CMOTECH_PRODUCT_6001			0x6001
@@ -1147,6 +1148,7 @@ static const struct usb_device_id option_ids[] = {
 	  .driver_info = ZLP },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
 	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
+	{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_RM500K, 0xff, 0x00, 0x00) },
 
 	{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
 	{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
Signature · 1 line
2.18.0
maintainer
#4 lore raw
Quoted 18 lines · Macpaul Lin

Add usb product id of the Quectel RM500K module.

RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs to write AT commands to this device node to query status, set APN, set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the data connection has been established, Linux host can access 5G data network via this interface.

"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs

usb-devices output for 0x7001:

Quoted 5 lines

---
Change for v2:
- Update USB interfaces descriptions in the commit message.
- Fix typo, format and contributers in the commit message.
- Update PID definition in numeric order.

Thanks for the update. Now applied.

Johan