pinctrl: nuvoton: add pinmux and GPIO driver for NPCM8XX
Subsystems (3)
Tomer Maimon
maintainercover pinctrl: nuvoton: add pinmux and GPIO driver for NPCM8XX
This patch set adds pinmux and GPIO controller for the Arbel NPCM8XX Baseboard Management Controller (BMC).
Arbel BMC NPCM8XX pinctrl driver based on Poleg NPCM7XX, except the pin mux mapping difference the NPCM8XX GPIO supports adjust debounce period time.
Arbel BMC NPCM8XX Pinmux functions accessible only for pin groups and pin configuration parameters available only for individual pins.
Arbel BMC NPCM8XX has eight identical GPIO modules, each module has 32 GPIO ports.
Most of the GPIO ports are multiplexed with other system functions.
The NPCM8XX pinctrl and GPIO driver was tested on the Arbel NPCM8XX evaluation board that running Arbel OpenBMC.
This patchset is based on the Arbel NPCM8XX pinctrl and GPIO 5.19 kernel patchset.
https://lwn.net/Articles/901214/
Tomer Maimon (2):
dt-binding: pinctrl: Add NPCM8XX pinctrl and GPIO documentation
pinctrl: nuvoton: add NPCM8XX pinctrl and GPIO driver
.../pinctrl/nuvoton,npcm845-pinctrl.yaml | 213 ++ drivers/pinctrl/Makefile | 2 +- drivers/pinctrl/nuvoton/Kconfig | 13 + drivers/pinctrl/nuvoton/Makefile | 1 + drivers/pinctrl/nuvoton/pinctrl-npcm8xx.c | 2556 +++++++++++++++++ 5 files changed, 2784 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml create mode 100644 drivers/pinctrl/nuvoton/pinctrl-npcm8xx.c
Signature · 1 line
2.33.0
Tomer Maimon
maintainerPATCH 1/2 dt-binding: pinctrl: Add NPCM8XX pinctrl and GPIO documentation
Added device tree binding documentation for Nuvoton Arbel BMC NPCM8XX pinmux and GPIO controller.
--- .../pinctrl/nuvoton,npcm845-pinctrl.yaml | 213 ++++++++++++++++++ 1 file changed, 213 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml
Documentation/devicetree/bindings/pinctrl/nuvoton,npcm845-pinctrl.yaml new file +213 -0
@@ -0,0 +1,213 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/nuvoton,npcm845-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Nuvoton NPCM845 Pin Controller and GPIO + +maintainers: + - Tomer Maimon <[email protected]> + +description: + The Nuvoton BMC NPCM8XX Pin Controller multi-function routed through + the multiplexing block, Each pin supports GPIO functionality (GPIOx) + and multiple functions that directly connect the pin to different + hardware blocks. + +properties: + compatible: + const: nuvoton,npcm845-pinctrl + + ranges: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 1 + + nuvoton,sysgcr: + $ref: /schemas/types.yaml#/definitions/phandle + description: a phandle to access GCR registers. + +patternProperties: + "^gpio@": + type: object + + description: + Eight GPIO banks that each contain between 32 GPIOs. + + properties: + gpio-controller: true + + '#gpio-cells': + const: 2 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + gpio-ranges: + maxItems: 1 + + required: + - gpio-controller + - '#gpio-cells' + - reg + - interrupts + - gpio-ranges + + "-mux": + $ref: pinmux-node.yaml# + + properties: + groups: + description: + One or more groups of pins to mux to a certain function + items: + enum: [ iox1, iox2, smb1d, smb2d, lkgpo1, lkgpo2, ioxh, gspi, + smb5b, smb5c, lkgpo0, pspi2, jm1, jm2, smb4den, smb4b, + smb4c, smb15, smb16, smb17, smb18, smb19, smb20, smb21, + smb22, smb23, smb4d, smb14, smb5, smb4, smb3, spi0cs1, + spi0cs2, spi0cs3, smb3c, smb3b, bmcuart0a, uart1, jtag2, + bmcuart1, uart2, bmcuart0b, r1err, r1md, r1oen, r2oen, + rmii3, r3oen, smb3d, fanin0, fanin1, fanin2, fanin3, fanin4, + fanin5, fanin6, fanin7, fanin8, fanin9, fanin10, fanin11, + fanin12, fanin13, fanin14, fanin15, pwm0, pwm1, pwm2, pwm3, + r2, r2err, r2md, r3rxer, ga20kbc, smb5d, lpc, espi, rg1, + rg1mdio, rg2, ddr, i3c0, i3c1, i3c2, i3c3, i3c4, i3c5, + smb0, smb1, smb2, smb2c, smb2b, smb1c, smb1b, smb8, smb9, + smb10, smb11, sd1, sd1pwr, pwm4, pwm5, pwm6, pwm7, pwm8, + pwm9, pwm10, pwm11, mmc8, mmc, mmcwp, mmccd, mmcrst, clkout, + serirq, lpcclk, scipme, sci, smb6, smb7, spi1, faninx, r1, + spi3, spi3cs1, spi3quad, spi3cs2, spi3cs3, nprd_smi, smb0b, + smb0c, smb0den, smb0d, ddc, rg2mdio, wdog1, wdog2, smb12, + smb13, spix, spixcs1, clkreq, hgpio0, hgpio1, hgpio2, hgpio3, + hgpio4, hgpio5, hgpio6, hgpio7 ] + + function: + description: + The function that a group of pins is muxed to + enum: [ iox1, iox2, smb1d, smb2d, lkgpo1, lkgpo2, ioxh, gspi, + smb5b, smb5c, lkgpo0, pspi2, jm1, jm2, smb4den, smb4b, + smb4c, smb15, smb16, smb17, smb18, smb19, smb20, smb21, + smb22, smb23, smb4d, smb14, smb5, smb4, smb3, spi0cs1, + spi0cs2, spi0cs3, smb3c, smb3b, bmcuart0a, uart1, jtag2, + bmcuart1, uart2, bmcuart0b, r1err, r1md, r1oen, r2oen, + rmii3, r3oen, smb3d, fanin0, fanin1, fanin2, fanin3, fanin4, + fanin5, fanin6, fanin7, fanin8, fanin9, fanin10, fanin11, + fanin12, fanin13, fanin14, fanin15, pwm0, pwm1, pwm2, pwm3, + r2, r2err, r2md, r3rxer, ga20kbc, smb5d, lpc, espi, rg1, + rg1mdio, rg2, ddr, i3c0, i3c1, i3c2, i3c3, i3c4, i3c5, + smb0, smb1, smb2, smb2c, smb2b, smb1c, smb1b, smb8, smb9, + smb10, smb11, sd1, sd1pwr, pwm4, pwm5, pwm6, pwm7, pwm8, + pwm9, pwm10, pwm11, mmc8, mmc, mmcwp, mmccd, mmcrst, clkout, + serirq, lpcclk, scipme, sci, smb6, smb7, spi1, faninx, r1, + spi3, spi3cs1, spi3quad, spi3cs2, spi3cs3, nprd_smi, smb0b, + smb0c, smb0den, smb0d, ddc, rg2mdio, wdog1, wdog2, smb12, + smb13, spix, spixcs1, clkreq, hgpio0, hgpio1, hgpio2, hgpio3, + hgpio4, hgpio5, hgpio6, hgpio7 ] + + dependencies: + groups: [ function ] + function: [ groups ] + + additionalProperties: false + + "^pin": + $ref: pincfg-node.yaml# + + properties: + pins: + description: + A list of pins to configure in certain ways, such as enabling + debouncing + + bias-disable: true + + bias-pull-up: true + + bias-pull-down: true + + input-enable: true + + output-low: true + + output-high: true + + drive-push-pull: true + + drive-open-drain: true + + input-debounce: + description: + Debouncing periods in microseconds, one period per interrupt + bank found in the controller + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + + slew-rate: + description: | + 0: Low rate + 1: High rate + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + + drive-strength: + enum: [ 0, 1, 2, 4, 8, 12 ] + + additionalProperties: false + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - ranges + - '#address-cells' + - '#size-cells' + - nuvoton,sysgcr + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/gpio/gpio.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + + pinctrl: pinctrl@f0800000 { + compatible = "nuvoton,npcm845-pinctrl"; + ranges = <0x0 0x0 0xf0010000 0x8000>; + #address-cells = <1>; + #size-cells = <1>; + nuvoton,sysgcr = <&gcr>; + + gpio0: gpio@f0010000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0xB0>; + interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>; + gpio-ranges = <&pinctrl 0 0 32>; + }; + + fanin0_pin: fanin0-mux { + groups = "fanin0"; + function = "fanin0"; + }; + + pin34_slew: pin34-slew { + pins = "GPIO34/I3C4_SDA"; + bias-disable; + }; + }; + }; +
Signature · 1 line
2.33.0
Tomer Maimon
maintainerPATCH 2/2 pinctrl: nuvoton: add NPCM8XX pinctrl and GPIO driver
In reply to Tomer MaimonAdd pinctrl and GPIO controller driver support to Arbel BMC NPCM8XX SoC.
Arbel BMC NPCM8XX pinctrl driver based on Poleg NPCM7XX, except the pin mux mapping difference the NPCM8XX GPIO supports adjust debounce period time.
--- drivers/pinctrl/Makefile | 2 +- drivers/pinctrl/nuvoton/Kconfig | 13 + drivers/pinctrl/nuvoton/Makefile | 1 + drivers/pinctrl/nuvoton/pinctrl-npcm8xx.c | 2556 +++++++++++++++++++++ 4 files changed, 2571 insertions(+), 1 deletion(-) create mode 100644 drivers/pinctrl/nuvoton/pinctrl-npcm8xx.c
drivers/pinctrl/Makefile +1 -1
@@ -57,7 +57,7 @@ obj-y += freescale/ obj-$(CONFIG_X86) += intel/ obj-y += mvebu/ obj-y += nomadik/ -obj-$(CONFIG_ARCH_NPCM7XX) += nuvoton/ +obj-$(CONFIG_ARCH_NPCM) += nuvoton/ obj-$(CONFIG_PINCTRL_PXA) += pxa/ obj-$(CONFIG_ARCH_QCOM) += qcom/ obj-$(CONFIG_PINCTRL_RALINK) += ralink/
drivers/pinctrl/nuvoton/Kconfig +13 -0
@@ -11,3 +11,16 @@ config PINCTRL_NPCM7XX help Say Y here to enable pin controller and GPIO support for Nuvoton NPCM750/730/715/705 SoCs. + +config PINCTRL_NPCM8XX + bool "Pinctrl and GPIO driver for Nuvoton NPCM8XX" + depends on (ARCH_NPCM || COMPILE_TEST) && OF + select PINMUX + select PINCONF + select GENERIC_PINCONF + select GPIOLIB + select GPIO_GENERIC + select GPIOLIB_IRQCHIP + help + Say Y here to enable pin controller and GPIO support + for Nuvoton NPCM845 SoC.
drivers/pinctrl/nuvoton/Makefile +1 -0
@@ -2,3 +2,4 @@ # Nuvoton pinctrl support obj-$(CONFIG_PINCTRL_NPCM7XX) += pinctrl-npcm7xx.o +obj-$(CONFIG_PINCTRL_NPCM8XX) += pinctrl-npcm8xx.o
drivers/pinctrl/nuvoton/pinctrl-npcm8xx.c new file +2556 -0
2,556 lines not on this page · raw message
Signature · 1 line
2.33.0