Skip to contentSkip to conversation

Add support for TI TPS65219 PMIC.

PATCH Superseded Jerome Neanne 3 participants 13 messages Aug 5, 2022 – Aug 23, 2022

Subsystems (7)

v3 of 7 Superseded Latest is v7 →

lore
Share & tools
lore
#0 lore raw

v3 cover Add support for TI TPS65219 PMIC.

This driver supports
- 3 Buck regulators and 4 LDOs
- low-power standby mode
- warm/soft reset
- basic fault handling (via interrupts).
- power button

Not implemented
- DVS

1-Regulators:
Full implementation and test
Visual check: cat /sys/kernel/debug/regulator/regulator_summary Full validation requires userspace-consumer and virtual-regulator LDO1 is not used and output can be probbed on TP84.

2-Reset WARM/COLD
test procedure: launch reboot on the console and check visually

warm vs. cold can be configured on the kernel command-line at boot time. Default is cold, but adding reboot=w
to kernel command allow testing warm reboot.

Alternative:
# echo warm > /sys/kernel/reboot/mode

3-SW Shutdown
test procedure: launch halt on the console and check visually

Note: enters in competition with other source during probe

Board Test Points can be used to check voltage after system shutdown. baseport is not handling wakeup.
A power OFF/ON cycle is needed to recover.

4-Interrupt Pin (nINT):

Interrupt occurring on PMIC TPS65219 is propagated to SOC through EXTINTn pin connected to gic500 interrupt controller

Interrupt lines for TPS65219 shows-up on console:
cat /proc/interrupts

Validation:
Create a Residual Voltage interrupt and handling and interrupt source is cleared. tps65219 0-0030: Registered residual voltage for LDO1
533: 1 0 tps65219_irq 35 Edge LDO1_RV

Mapped to power button (use TP90 to GND to emulate a physical button)

5-PB Startup and Shutdown:
New implementation to support both rising and falling edge.

TPS65219 has different interrupts compared to other TPS6521* chips. TPS65219 defines two interrupts for the powerbutton one for push and one for release.

Interrupt support: cat proc/interrupts

`557:          0          0  tps65219_irq  47 Edge      tps65219-pwrbutton.1.auto`
`558:          0          0  tps65219_irq  48 Edge      tps65219-pwrbutton.1.auto`

TPS65219 has a multipurpose pin called EN/PB/VSENSE that can be either:
- EN in which case it functions as an enable pin.
- VSENSE which compares the voltages and triggers an automatic on/off request.
- PB in which case it can be configured to trigger an interrupt to the SoC. ti,power-button reflects the last one of those options
where the board has a button wired to the pin and triggers
an interrupt on pressing it.

6-Changes vs v1:

6.1- Regulators:
- Further to Mark Brown review:
Use standard regmap helpers for set_voltage, enable and disable. tps65219_set_mode, return -EINVAL in default statement for clarity. Reshaped irq handler to report events through the notification API:
regulator_notifier_call_chain().
Use standard regulator events (consumer.h).

6.2- Device tree
- Further to Nishanth Menon review:
add tag DONOTMERGE
Board support is pending waiting for TI commitment.
This device tree is needed for driver test purpose but should not go upstream.

6.3- Bindings
- Further to Rob Herring review:
Squash interrupt commit into regulator dt-binding.
Squash pwrbutton commit into regulator dt-binding.
Remove interrupt-controller/cells properties because no consumer for those interrupts.

- Further to Mark Brown review:
Remove constraints on regulator-name.

- Pending for decision from Lee Jones further to Mark Brown review The entire binding document should probably be in MFD if it's going to have properties for other functions added to it.

6.4- Misc
- Further to Mark Brown review:
Use C++ (//) formatting for file header block including SPDX License in mfd, regulator and pwrbutton.

7-Changes vs v2:

7.1- Bindings
- Further to Markus Schneider-Pargmann review:
Fix description and align name with dts: ti,power-button

7.2- Maintainers
- Further to Nishanth Menon review:
On behalf of Markus SP. Remove MAINTAINERS-OMAP2-support-add-tps65218-pwrbutton.patch from the series.
Not needed, driver is not missing, went through INPUT tree instead.

Jerome Neanne (9):
DONOTMERGE: arm64: dts: ti: Add TI TPS65219 PMIC support for AM642 SK
board.
DONOTMERGE: arm64: dts: ti: Add pinmux and irq mapping for TPS65219
external interrupts
DONOTMERGE: arm64: dts: ti: k3-am642-sk: Enable tps65219 power-button
regulator: dt-bindings: Add TI TPS65219 PMIC bindings
mfd: drivers: Add TI TPS65219 PMIC support
mfd: drivers: Add interrupts support to TI TPS65219 PMIC
regulator: drivers: Add TI TPS65219 PMIC regulators support
Input: Add tps65219 interrupt driven powerbutton
arm64: defconfig: Add tps65219 as modules

Markus Schneider-Pargmann (1):
mfd: tps65219: Add power-button support

 .../bindings/regulator/ti,tps65219.yaml       | 173 +++++++
 MAINTAINERS                                   |   2 +
 arch/arm64/boot/dts/ti/k3-am642-sk.dts        | 115 +++++
 arch/arm64/configs/defconfig                  |   3 +
 drivers/input/misc/Kconfig                    |  10 +
 drivers/input/misc/Makefile                   |   1 +
 drivers/input/misc/tps65219-pwrbutton.c       | 150 ++++++
 drivers/mfd/Kconfig                           |  15 +
 drivers/mfd/Makefile                          |   1 +
 drivers/mfd/tps65219.c                        | 437 ++++++++++++++++++
 drivers/regulator/Kconfig                     |   9 +
 drivers/regulator/Makefile                    |   1 +
 drivers/regulator/tps65219-regulator.c        | 416 +++++++++++++++++
 include/linux/mfd/tps65219.h                  | 364 +++++++++++++++
 14 files changed, 1697 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/ti,tps65219.yaml
 create mode 100644 drivers/input/misc/tps65219-pwrbutton.c
 create mode 100644 drivers/mfd/tps65219.c
 create mode 100644 drivers/regulator/tps65219-regulator.c
 create mode 100644 include/linux/mfd/tps65219.h
Signature · 1 line
2.17.1
#1 lore raw

PATCH v3 1/10 DONOTMERGE: arm64: dts: ti: Add TI TPS65219 PMIC support for AM642 SK board.

Add support fot the TI Power Management IC TPS65219 on the AM642 SKEVM board.

Needed for driver testing but official board support pending. TI commitment is required before board upstream kick-off.

---
 arch/arm64/boot/dts/ti/k3-am642-sk.dts | 104 +++++++++++++++++++++++++
 1 file changed, 104 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +104 -0
index 2620469a7517..565b50810579 100644
@@ -150,6 +150,20 @@
 		vin-supply = <&com8_ls_en>;
 		gpio = <&main_gpio0 48 GPIO_ACTIVE_HIGH>;
 	};
+
+	vsel_sd_nddr: gpio-regulator {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel_sd_nddr_pins_default>;
+		regulator-name = "tps65219-LDO1-SEL-SD";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&ldo1_reg>;
+		gpios = <&main_gpio0 45 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
 };
 
 &main_pmx0 {
@@ -181,6 +195,13 @@
 		>;
 	};
 
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */
+			AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */
+		>;
+	};
+
 	main_i2c1_pins_default: main-i2c1-pins-default {
 		pinctrl-single,pins = <
 			AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
@@ -267,6 +288,12 @@
 			AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
 		>;
 	};
+
+	vsel_sd_nddr_pins_default: vsel-sd-nddr-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00b8, PIN_INPUT, 7) /* (Y7) PRG1_PRU0_GPO0.GPIO0_45 */
+		>;
+	};
 };
 
 &mcu_uart0 {
@@ -315,6 +342,83 @@
 	status = "disabled";
 };
 
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	tps65219: pmic@30 {
+		compatible = "ti,tps65219";
+		reg = <0x30>;
+		system-power-controller;
+
+		buck1-supply = <&vcc_3v3_sys>;
+		buck2-supply = <&vcc_3v3_sys>;
+		buck3-supply = <&vcc_3v3_sys>;
+		ldo1-supply = <&vcc_3v3_sys>;
+		ldo2-supply = <&buck2_reg>;
+		ldo3-supply = <&vcc_3v3_sys>;
+		ldo4-supply = <&vcc_3v3_sys>;
+
+		regulators {
+			buck1_reg: buck1 {
+				regulator-name = "VDD_CORE";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck2_reg: buck2 {
+				regulator-name = "VCC1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck3_reg: buck3 {
+				regulator-name = "VDD_LPDDR4";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: ldo1 {
+				regulator-name = "VDDSHV_SD_IO_PMIC";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-allow-bypass;
+			};
+
+			ldo2_reg: ldo2 {
+				regulator-name = "VDDAR_CORE";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: ldo3 {
+				regulator-name = "VDDA_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: ldo4 {
+				regulator-name = "VDD_PHY_2V5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
 &main_i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_i2c1_pins_default>;
Signature · 1 line
2.17.1
#2 lore raw

PATCH v3 2/10 DONOTMERGE: arm64: dts: ti: Add pinmux and irq mapping for TPS65219 external interrupts

In reply to Jerome Neanne

Interrupt occurring on PMIC TPS65219 is propagated to SOC through EXTINTn pin connected to gic500 interrupt controller

Needed for driver testing but official board support pending. TI commitment is required before board upstream kick-off.

---
 arch/arm64/boot/dts/ti/k3-am642-sk.dts | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +10 -0
index 565b50810579..1f7ce60ecb57 100644
@@ -294,6 +294,12 @@
 			AM64X_IOPAD(0x00b8, PIN_INPUT, 7) /* (Y7) PRG1_PRU0_GPO0.GPIO0_45 */
 		>;
 	};
+
+	pmic_irq_pins_default: pmic-irq-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0278, PIN_INPUT, 0) /* (C19) EXTINTn */
+		>;
+	};
 };
 
 &mcu_uart0 {
@@ -352,6 +358,10 @@
 		compatible = "ti,tps65219";
 		reg = <0x30>;
 		system-power-controller;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_irq_pins_default>;
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
 
 		buck1-supply = <&vcc_3v3_sys>;
 		buck2-supply = <&vcc_3v3_sys>;
Signature · 1 line
2.17.1
#3 lore raw

PATCH v3 3/10 DONOTMERGE: arm64: dts: ti: k3-am642-sk: Enable tps65219 power-button

In reply to Jerome Neanne

This board uses the pin as a power-button, enable it.

Needed for driver testing but official board support pending. TI commitment is required before board upstream kick-off.

---
 arch/arm64/boot/dts/ti/k3-am642-sk.dts | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/boot/dts/ti/k3-am642-sk.dts +1 -0
index 1f7ce60ecb57..238798ea6a79 100644
@@ -362,6 +362,7 @@
 		pinctrl-0 = <&pmic_irq_pins_default>;
 		interrupt-parent = <&gic500>;
 		interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+		ti,power-button;
 
 		buck1-supply = <&vcc_3v3_sys>;
 		buck2-supply = <&vcc_3v3_sys>;
Signature · 1 line
2.17.1
#4 lore raw

PATCH v3 4/10 regulator: dt-bindings: Add TI TPS65219 PMIC bindings

In reply to Jerome Neanne

Add TPS65219 PMIC bindings using json-schema.

Describe required properties and regname-supply. regname-supply is required when bypass mode is used for a regulator. Describes regulator topology.
Interrupts support.
Add a power-button property to configure the EN/PB/VSENSE pin as a powerbutton:

TPS65219 has a multipurpose pin called EN/PB/VSENSE that can be either:
- EN in which case it functions as an enable pin.
- VSENSE which compares the voltages and triggers an automatic on/off request.
- PB in which case it can be configured to trigger an interrupt to the SoC.
ti,power-button reflects the last one of those options
where the board has a button wired to the pin and triggers an interrupt on pressing it.

---
 .../bindings/regulator/ti,tps65219.yaml       | 173 ++++++++++++++++++
 1 file changed, 173 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/ti,tps65219.yaml
Documentation/devicetree/bindings/regulator/ti,tps65219.yaml new file +173 -0
new file mode 100644
index 000000000000..78be79930fda
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/ti,tps65219.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI tps65219 Power Management Integrated Circuit regulators
+
+maintainers:
+  - Jerome Neanne <[email protected]>
+
+description: |
+  Regulator nodes should be named to buck<number> and ldo<number>.
+
+properties:
+  compatible:
+    enum:
+      - ti,tps65219
+
+  reg:
+    maxItems: 1
+
+  system-power-controller:
+    type: boolean
+    description: Optional property that indicates that this device is
+      controlling system power.
+
+  interrupts:
+    description: Short-circuit, over-current, under-voltage for regulators, PB interrupts.
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    description: Specifies the PIN numbers and Flags, as defined in
+      include/dt-bindings/interrupt-controller/irq.h
+    const: 1
+
+  ti,power-button:
+    type: boolean
+    description: |
+      Optional property that sets the EN/PB/VSENSE pin to be a
+      power-button.
+      TPS65219 has a multipurpose pin called EN/PB/VSENSE that can be either
+      1. EN in which case it functions as an enable pin.
+      2. VSENSE which compares the voltages and triggers an automatic
+      on/off request.
+      3. PB in which case it can be configured to trigger an interrupt
+      to the SoC.
+      ti,power-button reflects the last one of those options
+      where the board has a button wired to the pin and triggers
+      an interrupt on pressing it.
+
+patternProperties:
+  "^buck[1-3]-supply$":
+    description: Input supply phandle of one regulator.
+
+  "^ldo[1-4]-supply$":
+    description: Input supply phandle of one regulator.
+
+  regulators:
+    type: object
+    description: |
+      list of regulators provided by this controller
+
+    patternProperties:
+      "^ldo[1-4]$":
+        type: object
+        $ref: regulator.yaml#
+        description:
+          Properties for single LDO regulator.
+
+        unevaluatedProperties: false
+
+      "^buck[1-3]$":
+        type: object
+        $ref: regulator.yaml#
+        description:
+          Properties for single BUCK regulator.
+
+        unevaluatedProperties: false
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - regulators
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        tps65219: pmic@30 {
+            compatible = "ti,tps65219";
+            reg = <0x30>;
+            buck1-supply = <&vcc_3v3_sys>;
+            buck2-supply = <&vcc_3v3_sys>;
+            buck3-supply = <&vcc_3v3_sys>;
+            ldo1-supply = <&vcc_3v3_sys>;
+            ldo2-supply = <&buck2_reg>;
+            ldo3-supply = <&vcc_3v3_sys>;
+            ldo4-supply = <&vcc_3v3_sys>;
+
+            pinctrl-0 = <&pmic_irq_pins_default>;
+
+            interrupt-parent = <&gic500>;
+            interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+            ti,power-button;
+
+            regulators {
+                buck1_reg: buck1 {
+                    regulator-name = "VDD_CORE";
+                    regulator-min-microvolt = <750000>;
+                    regulator-max-microvolt = <750000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+
+                buck2_reg: buck2 {
+                    regulator-name = "VCC1V8";
+                    regulator-min-microvolt = <1800000>;
+                    regulator-max-microvolt = <1800000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+
+                buck3_reg: buck3 {
+                    regulator-name = "VDD_LPDDR4";
+                    regulator-min-microvolt = <1100000>;
+                    regulator-max-microvolt = <1100000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+
+                ldo1_reg: ldo1 {
+                    regulator-name = "VDDSHV_SD_IO_PMIC";
+                    regulator-min-microvolt = <33000000>;
+                    regulator-max-microvolt = <33000000>;
+                };
+
+                ldo2_reg: ldo2 {
+                    regulator-name = "VDDAR_CORE";
+                    regulator-min-microvolt = <850000>;
+                    regulator-max-microvolt = <850000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+
+                ldo3_reg: ldo3 {
+                    regulator-name = "VDDA_1V8";
+                    regulator-min-microvolt = <18000000>;
+                    regulator-max-microvolt = <18000000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+
+                ldo4_reg: ldo4 {
+                    regulator-name = "VDD_PHY_2V5";
+                    regulator-min-microvolt = <25000000>;
+                    regulator-max-microvolt = <25000000>;
+                    regulator-boot-on;
+                    regulator-always-on;
+                };
+            };
+        };
+    };
Signature · 1 line
2.17.1
maintainer Reviewed-by on v3 4/10
#5 lore raw

Re: [PATCH v3 04/10] regulator: dt-bindings: Add TI TPS65219 PMIC bindings

Quoted 19 lines · Jerome Neanne

Add TPS65219 PMIC bindings using json-schema.

Describe required properties and regname-supply. regname-supply is required when bypass mode is used for a regulator. Describes regulator topology.
Interrupts support.
Add a power-button property to configure the EN/PB/VSENSE pin as a powerbutton:

TPS65219 has a multipurpose pin called EN/PB/VSENSE that can be either:
- EN in which case it functions as an enable pin.
- VSENSE which compares the voltages and triggers an automatic on/off request.
- PB in which case it can be configured to trigger an interrupt to the SoC.
ti,power-button reflects the last one of those options
where the board has a button wired to the pin and triggers an interrupt on pressing it.

Quoted 7 lines
---
 .../bindings/regulator/ti,tps65219.yaml       | 173 ++++++++++++++++++
 1 file changed, 173 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/regulator/ti,tps65219.yaml
#6 lore raw

PATCH v3 5/10 mfd: drivers: Add TI TPS65219 PMIC support

In reply to Jerome Neanne

The TPS65219 is a power management IC PMIC designed to supply a wide range of SoCs
in both portable and stationary applications.
Any SoC can control TPS65219 over a standard I2C interface.

It contains the following components:
- Regulators.
- Over Temperature warning and Shut down.
- GPIOs
- Multi Function Pins (MFP)

This patch adds support for tps65219 mfd device. At this time only the functionalities listed below are made available:

- Regulators probe and functionalities
- warm and cold reset support
- SW shutdown support

---
 MAINTAINERS                  |   1 +
 drivers/mfd/Kconfig          |  15 +++
 drivers/mfd/Makefile         |   1 +
 drivers/mfd/tps65219.c       | 214 +++++++++++++++++++++++++++++
 include/linux/mfd/tps65219.h | 251 +++++++++++++++++++++++++++++++++++
 5 files changed, 482 insertions(+)
 create mode 100644 drivers/mfd/tps65219.c
 create mode 100644 include/linux/mfd/tps65219.h
MAINTAINERS +1 -0
index fee3ecc2d6ca..ffd533b8debc 100644
@@ -14840,6 +14840,7 @@ F:	drivers/mfd/menelaus.c
 F:	drivers/mfd/palmas.c
 F:	drivers/mfd/tps65217.c
 F:	drivers/mfd/tps65218.c
+F:	drivers/mfd/tps65219.c
 F:	drivers/mfd/tps65910.c
 F:	drivers/mfd/twl-core.[ch]
 F:	drivers/mfd/twl4030*.c
drivers/mfd/Kconfig +15 -0
index 3b59456f5545..c66e56374a9a 100644
@@ -1574,6 +1574,21 @@ config MFD_TPS65218
 	  This driver can also be built as a module.  If so, the module
 	  will be called tps65218.
 
+config MFD_TPS65219
+	tristate "TI TPS65219 Power Management chips"
+	depends on I2C && OF
+	select MFD_CORE
+	select REGMAP_I2C
+	select REGMAP_IRQ
+	help
+	  If you say yes here you get support for the TPS65219 series of
+	  Power Management chips.
+	  These include voltage regulators, gpio and other features
+	  that are often used in portable devices.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called tps65219.
+
 config MFD_TPS6586X
 	bool "TI TPS6586x Power Management chips"
 	depends on I2C=y
drivers/mfd/Makefile +1 -0
index 858cacf659d6..a8ff3d6ea3ab 100644
@@ -101,6 +101,7 @@ obj-$(CONFIG_TPS6507X)		+= tps6507x.o
 obj-$(CONFIG_MFD_TPS65086)	+= tps65086.o
 obj-$(CONFIG_MFD_TPS65217)	+= tps65217.o
 obj-$(CONFIG_MFD_TPS65218)	+= tps65218.o
+obj-$(CONFIG_MFD_TPS65219)	+= tps65219.o
 obj-$(CONFIG_MFD_TPS65910)	+= tps65910.o
 obj-$(CONFIG_MFD_TPS65912)	+= tps65912-core.o
 obj-$(CONFIG_MFD_TPS65912_I2C)	+= tps65912-i2c.o
drivers/mfd/tps65219.c new file +214 -0

214 lines not on this page · raw message

include/linux/mfd/tps65219.h new file +251 -0

251 lines not on this page · raw message

Signature · 1 line
2.17.1
#7 lore raw

PATCH v3 6/10 mfd: drivers: Add interrupts support to TI TPS65219 PMIC

In reply to Jerome Neanne

Add TPS65219 support for interrupts through regmap_irq_chip

---
 drivers/mfd/tps65219.c       | 217 ++++++++++++++++++++++++++++++++++-
 include/linux/mfd/tps65219.h | 113 ++++++++++++++++++
 2 files changed, 328 insertions(+), 2 deletions(-)
drivers/mfd/tps65219.c +215 -2
index c3bf975ea6c7..7366f251c21d 100644
@@ -107,8 +107,73 @@ static void pmic_do_poweroff(void)
 	tps65219_soft_shutdown(tps);
 }
 
-static const struct mfd_cell tps65219_cells[] = {
-	{ .name = "tps65219-regulator", },
+static const struct resource tps65219_pwrbutton_resources[] = {
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_PB_FALLING_EDGE_DETECT, "falling"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_PB_RISING_EDGE_DETECT, "rising"),
+};
+
+static const struct resource tps65219_regulator_resources[] = {
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO3_SCG, "LDO3_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO3_OC, "LDO3_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO3_UV, "LDO3_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO4_SCG, "LDO4_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO4_OC, "LDO4_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO4_UV, "LDO4_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO1_SCG, "LDO1_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO1_OC, "LDO1_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO1_UV, "LDO1_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO2_SCG, "LDO2_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO2_OC, "LDO2_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO2_UV, "LDO2_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK3_SCG, "BUCK3_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK3_OC, "BUCK3_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK3_NEG_OC, "BUCK3_NEG_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK3_UV, "BUCK3_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK1_SCG, "BUCK1_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK1_OC, "BUCK1_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK1_NEG_OC, "BUCK1_NEG_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK1_UV, "BUCK1_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK2_SCG, "BUCK2_SCG"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK2_OC, "BUCK2_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK2_NEG_OC, "BUCK2_NEG_OC"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK2_UV, "BUCK2_UV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK1_RV, "BUCK1_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK2_RV, "BUCK2_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK3_RV, "BUCK3_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO1_RV, "LDO1_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO2_RV, "LDO2_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO3_RV, "LDO3_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO4_RV, "LDO4_RV"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK1_RV_SD, "BUCK1_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK2_RV_SD, "BUCK2_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_BUCK3_RV_SD, "BUCK3_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO1_RV_SD, "LDO1_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO2_RV_SD, "LDO2_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO3_RV_SD, "LDO3_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_LDO4_RV_SD, "LDO4_RV_SD"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_TIMEOUT, "TIMEOUT"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_3_WARM, "SENSOR_3_WARM"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_2_WARM, "SENSOR_2_WARM"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_1_WARM, "SENSOR_1_WARM"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_0_WARM, "SENSOR_0_WARM"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_3_HOT, "SENSOR_3_HOT"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_2_HOT, "SENSOR_2_HOT"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_1_HOT, "SENSOR_1_HOT"),
+	DEFINE_RES_IRQ_NAMED(TPS65219_INT_SENSOR_0_HOT, "SENSOR_0_HOT"),
+};
+
+#define TPS65219_MAX_CELLS 2
+
+static const struct mfd_cell tps65219_regulator_cell = {
+	.name = "tps65219-regulator",
+	.resources = tps65219_regulator_resources,
+	.num_resources = ARRAY_SIZE(tps65219_regulator_resources),
+};
+
+static const struct mfd_cell tps65219_pwrbutton_cell = {
+	.name = "tps65219-pwrbutton",
+	.resources = tps65219_pwrbutton_resources,
+	.num_resources = ARRAY_SIZE(tps65219_pwrbutton_resources),
 };
 
 static const struct regmap_config tps65219_regmap_config = {
@@ -117,6 +182,147 @@ static const struct regmap_config tps65219_regmap_config = {
 	.max_register = TPS65219_REG_FACTORY_CONFIG_2,
 };
 
+/*
+ * Mapping of main IRQ register bits to sub-IRQ register offsets so that we can
+ * access corect sub-IRQ registers based on bits that are set in main IRQ
+ * register.
+ */
+/* Timeout Residual Voltage Shutdown */
+static unsigned int bit0_offsets[] = {TPS65219_TO_RV_POS};
+static unsigned int bit1_offsets[] = {TPS65219_RV_POS};	/* Residual Voltage */
+static unsigned int bit2_offsets[] = {TPS65219_SYS_POS};	/* System */
+static unsigned int bit3_offsets[] = {TPS65219_BUCK_1_2_POS};	/* Buck 1-2 */
+static unsigned int bit4_offsets[] = {TPS65219_BUCK_3_POS};	/* Buck 3 */
+static unsigned int bit5_offsets[] = {TPS65219_LDO_1_2_POS};	/* LDO 1-2 */
+static unsigned int bit6_offsets[] = {TPS65219_LDO_3_4_POS};	/* LDO 3-4 */
+static unsigned int bit7_offsets[] = {TPS65219_PB_POS};	/* Power Button */
+
+static struct regmap_irq_sub_irq_map tps65219_sub_irq_offsets[] = {
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit0_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit1_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit2_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit3_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit4_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit5_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit6_offsets),
+	REGMAP_IRQ_MAIN_REG_OFFSET(bit7_offsets),
+};
+
+static struct regmap_irq tps65219_irqs[] = {
+	REGMAP_IRQ_REG(TPS65219_INT_LDO3_SCG, TPS65219_LDO_3_4_POS,
+		       TPS65219_INT_LDO3_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO3_OC,
+		       TPS65219_LDO_3_4_POS, TPS65219_INT_LDO3_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO3_UV, TPS65219_LDO_3_4_POS,
+		       TPS65219_INT_LDO3_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO4_SCG, TPS65219_LDO_3_4_POS,
+		       TPS65219_INT_LDO4_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO4_OC, TPS65219_LDO_3_4_POS,
+		       TPS65219_INT_LDO4_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO4_UV, TPS65219_LDO_3_4_POS,
+		       TPS65219_INT_LDO4_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO1_SCG,
+		       TPS65219_LDO_1_2_POS, TPS65219_INT_LDO1_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO1_OC, TPS65219_LDO_1_2_POS,
+		       TPS65219_INT_LDO1_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO1_UV, TPS65219_LDO_1_2_POS,
+		       TPS65219_INT_LDO1_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO2_SCG, TPS65219_LDO_1_2_POS,
+		       TPS65219_INT_LDO2_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO2_OC, TPS65219_LDO_1_2_POS,
+		       TPS65219_INT_LDO2_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO2_UV, TPS65219_LDO_1_2_POS,
+		       TPS65219_INT_LDO2_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK3_SCG, TPS65219_BUCK_3_POS,
+		       TPS65219_INT_BUCK3_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK3_OC, TPS65219_BUCK_3_POS,
+		       TPS65219_INT_BUCK3_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK3_NEG_OC, TPS65219_BUCK_3_POS,
+		       TPS65219_INT_BUCK3_NEG_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK3_UV, TPS65219_BUCK_3_POS,
+		       TPS65219_INT_BUCK3_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK2_SCG, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK2_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK2_OC, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK2_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK2_NEG_OC, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK2_NEG_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK2_UV, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK2_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK1_SCG, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK1_SCG_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK1_OC, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK1_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK1_NEG_OC, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK1_NEG_OC_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK1_UV, TPS65219_BUCK_1_2_POS,
+		       TPS65219_INT_BUCK1_UV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_3_WARM,
+		       TPS65219_SYS_POS, TPS65219_INT_SENSOR_3_WARM_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_2_WARM, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_2_WARM_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_1_WARM, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_1_WARM_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_0_WARM, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_0_WARM_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_3_HOT, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_3_HOT_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_2_HOT, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_2_HOT_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_1_HOT, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_1_HOT_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_SENSOR_0_HOT, TPS65219_SYS_POS,
+		       TPS65219_INT_SENSOR_0_HOT_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK1_RV, TPS65219_RV_POS,
+		       TPS65219_INT_BUCK1_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK2_RV, TPS65219_RV_POS,
+		       TPS65219_INT_BUCK2_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK3_RV, TPS65219_RV_POS,
+		       TPS65219_INT_BUCK3_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO1_RV, TPS65219_RV_POS,
+		       TPS65219_INT_LDO1_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO2_RV, TPS65219_RV_POS,
+		       TPS65219_INT_LDO2_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO3_RV, TPS65219_RV_POS,
+		       TPS65219_INT_LDO3_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO4_RV, TPS65219_RV_POS,
+		       TPS65219_INT_LDO4_RV_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK1_RV_SD,
+		       TPS65219_TO_RV_POS, TPS65219_INT_BUCK1_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK2_RV_SD,
+		       TPS65219_TO_RV_POS, TPS65219_INT_BUCK2_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_BUCK3_RV_SD, TPS65219_TO_RV_POS,
+		       TPS65219_INT_BUCK3_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO1_RV_SD, TPS65219_TO_RV_POS,
+		       TPS65219_INT_LDO1_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO2_RV_SD, TPS65219_TO_RV_POS,
+		       TPS65219_INT_LDO2_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO3_RV_SD,
+		       TPS65219_TO_RV_POS, TPS65219_INT_LDO3_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_LDO4_RV_SD, TPS65219_TO_RV_POS,
+		       TPS65219_INT_LDO4_RV_SD_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_TIMEOUT, TPS65219_TO_RV_POS,
+		       TPS65219_INT_TIMEOUT_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_PB_FALLING_EDGE_DETECT,
+		       TPS65219_PB_POS, TPS65219_INT_PB_FALLING_EDGE_DET_MASK),
+	REGMAP_IRQ_REG(TPS65219_INT_PB_RISING_EDGE_DETECT, TPS65219_PB_POS,
+		       TPS65219_INT_PB_RISING_EDGE_DET_MASK),
+};
+
+static struct regmap_irq_chip tps65219_irq_chip = {
+	.name = "tps65219_irq",
+	.main_status = TPS65219_REG_INT_SOURCE,
+	.num_main_regs = 1,
+	.num_main_status_bits = 8,
+	.irqs = tps65219_irqs,
+	.num_irqs = ARRAY_SIZE(tps65219_irqs),
+	.status_base = TPS65219_REG_INT_LDO_3_4,
+	.ack_base = TPS65219_REG_INT_LDO_3_4,
+	.clear_ack = 1,
+	.num_regs = 8,
+	.sub_reg_offsets = &tps65219_sub_irq_offsets[0],
+};
+
 static const struct of_device_id of_tps65219_match_table[] = {
 	{ .compatible = "ti,tps65219", },
 	{}
@@ -137,6 +343,7 @@ static int tps65219_probe(struct i2c_client *client,
 
 	i2c_set_clientdata(client, tps);
 	tps->dev = &client->dev;
+	tps->irq = client->irq;
 	tps->regmap = devm_regmap_init_i2c(client, &tps65219_regmap_config);
 	if (IS_ERR(tps->regmap)) {
 		ret = PTR_ERR(tps->regmap);
@@ -145,6 +352,12 @@ static int tps65219_probe(struct i2c_client *client,
 		return ret;
 	}
 
+	ret = devm_regmap_add_irq_chip(&client->dev, tps->regmap, tps->irq,
+				       IRQF_ONESHOT, 0, &tps65219_irq_chip,
+				       &tps->irq_data);
+	if (ret)
+		return ret;
+
 	ret = regmap_read(tps->regmap, TPS65219_REG_TI_DEV_ID, &chipid);
 	if (ret) {
 		dev_err(tps->dev, "Failed to read device ID: %d\n", ret);
include/linux/mfd/tps65219.h +113 -0

131 lines not on this page · raw message

Signature · 1 line
2.17.1
#8 lore raw

PATCH v3 7/10 mfd: tps65219: Add power-button support

In reply to Jerome Neanne

From: Markus Schneider-Pargmann <[email protected]>

Using a power-button on the EN/PB/VSENSE pin of TPS65219 is optional, so this driver adds the mfd cell for tps65219-pwrbutton only if needed. Two interrupts are passed to the driver.

---
 drivers/mfd/tps65219.c | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)
drivers/mfd/tps65219.c +13 -3
index 7366f251c21d..c2136662627c 100644
@@ -335,7 +335,10 @@ static int tps65219_probe(struct i2c_client *client,
 	struct tps65219 *tps;
 	int ret;
 	unsigned int chipid;
+	bool pwr_button;
 	bool sys_pwr;
+	struct mfd_cell cells[TPS65219_MAX_CELLS];
+	int nr_cells = 0;
 
 	tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL);
 	if (!tps)
@@ -364,9 +367,16 @@ static int tps65219_probe(struct i2c_client *client,
 		return ret;
 	}
 
-	ret = devm_mfd_add_devices(tps->dev, PLATFORM_DEVID_AUTO, tps65219_cells,
-				   ARRAY_SIZE(tps65219_cells), NULL, 0,
-				   NULL);
+	memcpy(&cells[nr_cells++], &tps65219_regulator_cell,
+	       sizeof(tps65219_regulator_cell));
+	pwr_button = of_property_read_bool(tps->dev->of_node, "ti,power-button");
+	if (pwr_button)
+		memcpy(&cells[nr_cells++], &tps65219_pwrbutton_cell,
+		       sizeof(tps65219_pwrbutton_cell));
+
+	ret = devm_mfd_add_devices(tps->dev, PLATFORM_DEVID_AUTO, cells,
+				   nr_cells, NULL, 0,
+				   regmap_irq_get_domain(tps->irq_data));
 	if (ret) {
 		dev_err(tps->dev, "mfd_add_devices failed: %d\n", ret);
 		return ret;
Signature · 1 line
2.17.1
#9 lore raw

PATCH v3 8/10 regulator: drivers: Add TI TPS65219 PMIC regulators support

In reply to Jerome Neanne

The regulators set consists of 3 bucks DCDCs and 4 LDOs. The output voltages are configurable and are meant to supply power to the main processor and other components.

Validation:
Visual check: cat /sys/kernel/debug/regulator/regulator_summary
Validation: userspace-consumer and virtual-regulator required to test further

Enable/Disable:
cat /sys/devices/platform/userspace-consumer-VDDSHV_SD_IO_PMIC/state echo disabled > /sys/devices/platform/ userspace-consumer-VDDSHV_SD_IO_PMIC/state
echo enabled > /sys/devices/platform/ userspace-consumer-VDDSHV_SD_IO_PMIC/state

Change voltage:
cat /sys/devices/platform/regulator-virtual-ldo1/min_microvolts echo 1000000 > /sys/devices/platform/regulator-virtual-ldo1/ min_microvolts
echo 3000000 > /sys/devices/platform/regulator-virtual-ldo1/ max_microvolts

---
 MAINTAINERS                            |   1 +
 drivers/regulator/Kconfig              |   9 +
 drivers/regulator/Makefile             |   1 +
 drivers/regulator/tps65219-regulator.c | 416 +++++++++++++++++++++++++
 4 files changed, 427 insertions(+)
 create mode 100644 drivers/regulator/tps65219-regulator.c
MAINTAINERS +1 -0
index ffd533b8debc..faa9b2b7851b 100644
@@ -14850,6 +14850,7 @@ F:	drivers/regulator/palmas-regulator*.c
 F:	drivers/regulator/pbias-regulator.c
 F:	drivers/regulator/tps65217-regulator.c
 F:	drivers/regulator/tps65218-regulator.c
+F:	drivers/regulator/tps65219-regulator.c
 F:	drivers/regulator/tps65910-regulator.c
 F:	drivers/regulator/twl-regulator.c
 F:	drivers/regulator/twl6030-regulator.c
drivers/regulator/Kconfig +9 -0
index 23e3e4a35cc9..f9bd683baa38 100644
@@ -1384,6 +1384,15 @@ config REGULATOR_TPS65218
 	  voltage regulators. It supports software based voltage control
 	  for different voltage domains
 
+config REGULATOR_TPS65219
+	tristate "TI TPS65219 Power regulators"
+	depends on MFD_TPS65219 && OF
+	help
+	  This driver supports TPS65219 voltage regulator chips.
+	  TPS65219 series of PMICs have 3 single phase BUCKs & 4 LDOs
+	  voltage regulators. It supports software based voltage control
+	  for different voltage domains.
+
 config REGULATOR_TPS6524X
 	tristate "TI TPS6524X Power regulators"
 	depends on SPI
drivers/regulator/Makefile +1 -0
index fa49bb6cc544..d7734a8dfbaf 100644
@@ -162,6 +162,7 @@ obj-$(CONFIG_REGULATOR_TPS65086) += tps65086-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65090) += tps65090-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65217) += tps65217-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65218) += tps65218-regulator.o
+obj-$(CONFIG_REGULATOR_TPS65219) += tps65219-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6524X) += tps6524x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS6586X) += tps6586x-regulator.o
 obj-$(CONFIG_REGULATOR_TPS65910) += tps65910-regulator.o
drivers/regulator/tps65219-regulator.c new file +416 -0

416 lines not on this page · raw message

Signature · 1 line
2.17.1
#10 lore raw

PATCH v3 9/10 Input: Add tps65219 interrupt driven powerbutton

In reply to Jerome Neanne

TPS65219 has different interrupts compared to other TPS6521* chips. TPS65219 defines two interrupts for the powerbutton one for push and one for release.

This driver is very simple in that it maps the push interrupt to a key input and the release interrupt to a key release.

---
 drivers/input/misc/Kconfig              |  10 ++
 drivers/input/misc/Makefile             |   1 +
 drivers/input/misc/tps65219-pwrbutton.c | 150 ++++++++++++++++++++++++
 3 files changed, 161 insertions(+)
 create mode 100644 drivers/input/misc/tps65219-pwrbutton.c
drivers/input/misc/Kconfig +10 -0
index a18ab7358d8f..18d4a321e7ff 100644
@@ -468,6 +468,16 @@ config INPUT_TPS65218_PWRBUTTON
 	  To compile this driver as a module, choose M here. The module will
 	  be called tps65218-pwrbutton.
 
+config INPUT_TPS65219_PWRBUTTON
+	tristate "TPS65219 Power button driver"
+	depends on MFD_TPS65219
+	help
+	  Say Y here if you want to enable power button reporting for
+	  TPS65219 Power Management IC devices.
+
+	  To compile this driver as a module, choose M here. The module will
+	  be called tps65219-pwrbutton.
+
 config INPUT_AXP20X_PEK
 	tristate "X-Powers AXP20X power button driver"
 	depends on MFD_AXP20X
drivers/input/misc/Makefile +1 -0
index 28dfc444f0a9..fe8f47402d12 100644
@@ -78,6 +78,7 @@ obj-$(CONFIG_INPUT_SOC_BUTTON_ARRAY)	+= soc_button_array.o
 obj-$(CONFIG_INPUT_SPARCSPKR)		+= sparcspkr.o
 obj-$(CONFIG_INPUT_STPMIC1_ONKEY)  	+= stpmic1_onkey.o
 obj-$(CONFIG_INPUT_TPS65218_PWRBUTTON)	+= tps65218-pwrbutton.o
+obj-$(CONFIG_INPUT_TPS65219_PWRBUTTON)	+= tps65219-pwrbutton.o
 obj-$(CONFIG_INPUT_TWL4030_PWRBUTTON)	+= twl4030-pwrbutton.o
 obj-$(CONFIG_INPUT_TWL4030_VIBRA)	+= twl4030-vibra.o
 obj-$(CONFIG_INPUT_TWL6040_VIBRA)	+= twl6040-vibra.o
drivers/input/misc/tps65219-pwrbutton.c new file +150 -0

150 lines not on this page · raw message

Signature · 1 line
2.17.1
#11 lore raw

PATCH v3 10/10 arm64: defconfig: Add tps65219 as modules

In reply to Jerome Neanne

This adds defconfig option to support TPS65219 PMIC, MFD, Regulators and power-button.

---
 arch/arm64/configs/defconfig | 3 +++
 1 file changed, 3 insertions(+)
arch/arm64/configs/defconfig +3 -0
index d5b2d2dd4904..d64e00355fcd 100644
@@ -406,6 +406,7 @@ CONFIG_TOUCHSCREEN_GOODIX=m
 CONFIG_TOUCHSCREEN_EDT_FT5X06=m
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_PM8941_PWRKEY=y
+CONFIG_INPUT_TPS65219_PWRBUTTON=m
 CONFIG_INPUT_PM8XXX_VIBRATOR=m
 CONFIG_INPUT_PWM_BEEPER=m
 CONFIG_INPUT_PWM_VIBRA=m
@@ -639,6 +640,7 @@ CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
 CONFIG_MFD_SEC_CORE=y
 CONFIG_MFD_SL28CPLD=y
+CONFIG_MFD_TPS65219=m
 CONFIG_MFD_ROHM_BD718XX=y
 CONFIG_MFD_WCD934X=m
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -666,6 +668,7 @@ CONFIG_REGULATOR_QCOM_SPMI=y
 CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_S2MPS11=y
 CONFIG_REGULATOR_TPS65132=m
+CONFIG_REGULATOR_TPS65219=m
 CONFIG_REGULATOR_VCTRL=m
 CONFIG_RC_CORE=m
 CONFIG_RC_DECODERS=y
Signature · 1 line
2.17.1
maintainer
#12 lore raw

Re: (subset) [PATCH v3 00/10] Add support for TI TPS65219 PMIC.

In reply to Jerome Neanne
Quoted 8 lines · Jerome Neanne

This driver supports
- 3 Buck regulators and 4 LDOs
- low-power standby mode
- warm/soft reset
- basic fault handling (via interrupts).
- power button

[...]

Applied to

https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next

Thanks!

[04/10] regulator: dt-bindings: Add TI TPS65219 PMIC bindings

        commit: 4d2aed6ee306ccdcae51f550309bfb82ebf31b01
[08/10] regulator: drivers: Add TI TPS65219 PMIC regulators support
        commit: c12ac5fc3e0af29851785e557e243663b4fc7f4b

All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying to this mail.

Thanks,
Mark

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel