Skip to contentSkip to conversation

board: gateworks: venice: update GW74xx PMIC config

PATCH New Tim Harvey 2 participants 2 messages Sep 8, 2022 – Oct 21, 2022

lore
Share & tools
lore

Tim Harvey

author
#0 lore raw

PATCH v2 1/1 board: gateworks: venice: update GW74xx PMIC config

Update the GW74xx PMIC configuration:
- increase VDD_SOC DVS1 to 0.85V per datasheet
- increase VDD_SOC DVS0 to 0.95V before first DRAM access
- increase VDD_ARM DVS0 to 0.95V to support kernel overdrive voltage (OD)
- remove unnecessary changes to VDD_DRAM as we don't use 3GHz DRAM
- remove unnecessary change to LDO2 as it is unused

v2: update commit log with more detail

---
 board/gateworks/venice/spl.c | 16 +++++++---------
 1 file changed, 7 insertions(+), 9 deletions(-)
board/gateworks/venice/spl.c +7 -9
index 56a985ed668f..98931c04754e 100644
@@ -156,17 +156,15 @@ static int power_init_board(void)
 		/* Buck 1 DVS control through PMIC_STBY_REQ */
 		dm_i2c_reg_write(dev, PCA9450_BUCK1CTRL, 0x59);
 
-		/* Set DVS1 to 0.8v for suspend */
-		dm_i2c_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x10);
+		/* Set DVS1 to 0.85v for suspend */
+		dm_i2c_reg_write(dev, PCA9450_BUCK1OUT_DVS1, 0x14);
 
-		/* increase VDD_DRAM to 0.95v for 3Ghz DDR */
-		dm_i2c_reg_write(dev, PCA9450_BUCK3OUT_DVS0, 0x1C);
+		/* increase VDD_SOC to 0.95V before first DRAM access */
+		dm_i2c_reg_write(dev, PCA9450_BUCK1OUT_DVS0, 0x1C);
 
-		/* VDD_DRAM off in suspend: B1_ENMODE=10 */
-		dm_i2c_reg_write(dev, PCA9450_BUCK3CTRL, 0x4a);
-
-		/* set VDD_SNVS_0V8 from default 0.85V */
-		dm_i2c_reg_write(dev, PCA9450_LDO2CTRL, 0xC0);
+		/* Kernel uses OD/OD freq for SOC */
+		/* To avoid timing risk from SOC to ARM, increase VDD_ARM to OD voltage 0.95v */
+		dm_i2c_reg_write(dev, PCA9450_BUCK2OUT_DVS0, 0x1C);
 
 		/* set WDOG_B_CFG to cold reset */
 		dm_i2c_reg_write(dev, PCA9450_RESET_CTRL, 0xA1);
Signature · 1 line
2.25.1
#1 lore raw

PATCH v2 1/1 board: gateworks: venice: update GW74xx PMIC config

Quoted 8 lines

Update the GW74xx PMIC configuration:
- increase VDD_SOC DVS1 to 0.85V per datasheet
- increase VDD_SOC DVS0 to 0.95V before first DRAM access
- increase VDD_ARM DVS0 to 0.95V to support kernel overdrive voltage (OD)
- remove unnecessary changes to VDD_DRAM as we don't use 3GHz DRAM
- remove unnecessary change to LDO2 as it is unused

v2: update commit log with more detail

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================