Add riscv semihosting support in u-boot
Subsystems (3)
v5 cover Add riscv semihosting support in u-boot
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
- Check arch dependencies for SEMIHOSTING as well as SPL_SEMIHOSTING
config options as per Sean's comment.
- arch/riscv/lib/interrupts.c: Check for post and pre instructions
of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a disable_semihosting and epc += 4 and return.
Compilation and test commands for SPL and S-mode configurations
=================================================================
U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.bin
U-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000
Kautuk Consul (3):
lib: Add common semihosting library arch/riscv: add semihosting support for RISC-V
board: qemu-riscv: enable semihosting
arch/arm/Kconfig | 46 ------- arch/arm/lib/semihosting.c | 181 +------------------------- arch/riscv/include/asm/spl.h | 1 + arch/riscv/lib/Makefile | 2 + arch/riscv/lib/interrupts.c | 25 ++++ arch/riscv/lib/semihosting.c | 24 ++++ configs/qemu-riscv32_defconfig | 4 + configs/qemu-riscv32_smode_defconfig | 4 + configs/qemu-riscv32_spl_defconfig | 7 + configs/qemu-riscv64_defconfig | 4 + configs/qemu-riscv64_smode_defconfig | 4 + configs/qemu-riscv64_spl_defconfig | 7 + include/semihosting.h | 11 ++ lib/Kconfig | 47 +++++++ lib/Makefile | 2 + lib/semihosting.c | 186 +++++++++++++++++++++++++++ 16 files changed, 329 insertions(+), 226 deletions(-) create mode 100644 arch/riscv/lib/semihosting.c create mode 100644 lib/semihosting.c
Signature · 1 line
2.34.1
PATCH v5 1/3 lib: Add common semihosting library
We factor out the arch-independent parts of the ARM semihosting implementation as a common library so that it can be shared with RISC-V.
--- arch/arm/Kconfig | 46 --------- arch/arm/lib/semihosting.c | 181 +----------------------------------- include/semihosting.h | 11 +++ lib/Kconfig | 47 ++++++++++ lib/Makefile | 2 + lib/semihosting.c | 186 +++++++++++++++++++++++++++++++++++++ 6 files changed, 247 insertions(+), 226 deletions(-) create mode 100644 lib/semihosting.c
arch/arm/Kconfig +0 -46
@@ -413,52 +413,6 @@ config ARM_SMCCC This should be enabled if U-Boot needs to communicate with system firmware (for example, PSCI) according to SMCCC. -config SEMIHOSTING - bool "Support ARM semihosting" - help - Semihosting is a method for a target to communicate with a host - debugger. It uses special instructions which the debugger will trap - on and interpret. This allows U-Boot to read/write files, print to - the console, and execute arbitrary commands on the host system. - - Enabling this option will add support for reading and writing files - on the host system. If you don't have a debugger attached then trying - to do this will likely cause U-Boot to hang. Say 'n' if you are unsure. - -config SEMIHOSTING_FALLBACK - bool "Recover gracefully when semihosting fails" - depends on SEMIHOSTING && ARM64 - default y - help - Normally, if U-Boot makes a semihosting call and no debugger is - attached, then it will panic due to a synchronous abort - exception. This config adds an exception handler which will allow - U-Boot to recover. Say 'y' if unsure. - -config SPL_SEMIHOSTING - bool "Support ARM semihosting in SPL" - depends on SPL - help - Semihosting is a method for a target to communicate with a host - debugger. It uses special instructions which the debugger will trap - on and interpret. This allows U-Boot to read/write files, print to - the console, and execute arbitrary commands on the host system. - - Enabling this option will add support for reading and writing files - on the host system. If you don't have a debugger attached then trying - to do this will likely cause U-Boot to hang. Say 'n' if you are unsure. - -config SPL_SEMIHOSTING_FALLBACK - bool "Recover gracefully when semihosting fails in SPL" - depends on SPL_SEMIHOSTING && ARM64 - select ARMV8_SPL_EXCEPTION_VECTORS - default y - help - Normally, if U-Boot makes a semihosting call and no debugger is - attached, then it will panic due to a synchronous abort - exception. This config adds an exception handler which will allow - U-Boot to recover. Say 'y' if unsure. - config SYS_THUMB_BUILD bool "Build U-Boot using the Thumb instruction set" depends on !ARM64
arch/arm/lib/semihosting.c +1 -180
194 lines not on this page · raw message
include/semihosting.h +11 -0
@@ -17,6 +17,17 @@#define SMH_T32_SVC 0xDFAB#define SMH_T32_HLT 0xBABC +/** +* smh_trap() - ARCH-specific semihosting call. +* +* Semihosting library/driver can use this function to do the +* actual semihosting calls. +* +* Return: Error code defined by semihosting spec. +*/ + +long smh_trap (unsigned int sysnum,void *addr); +#if CONFIG_IS_ENABLED (SEMIHOSTING_FALLBACK )/** * semihosting_enabled() - Determine whether semihosting is supported
lib/Kconfig +47 -0
53 lines not on this page · raw message
lib/Makefile +2 -0
@@ -145,6 +145,8 @@ obj-y += date.o obj-y += rtc-lib.o obj-$(CONFIG_LIB_ELF) += elf.o +obj-$(CONFIG_$(SPL_TPL_)SEMIHOSTING) += semihosting.o + # # Build a fast OID lookup registry from include/linux/oid_registry.h #
lib/semihosting.c new file +186 -0
186 lines not on this page · raw message
Signature · 1 line
2.34.1
Re: [PATCH v5 1/3] lib: Add common semihosting library
Quoted 548 lines · Kautuk Consul
We factor out the arch-independent parts of the ARM semihosting implementation as a common library so that it can be shared with RISC-V.
Signed-off-by Kautuk Consul <[email protected]>--- arch/arm/Kconfig | 46 --------- arch/arm/lib/semihosting.c | 181 +----------------------------------- include/semihosting.h | 11 +++ lib/Kconfig | 47 ++++++++++ lib/Makefile | 2 + lib/semihosting.c | 186 +++++++++++++++++++++++++++++++++++++ 6 files changed, 247 insertions(+), 226 deletions(-) create mode 100644 lib/semihosting.carch/arm/Kconfig +0
-46@@ -413,52 +413,6 @@ config ARM_SMCCC This should be enabled if U-Boot needs to communicate with system firmware (for example, PSCI) according to SMCCC. -config SEMIHOSTING - bool "Support ARM semihosting" - help - Semihosting is a method for a target to communicate with a host - debugger. It uses special instructions which the debugger will trap - on and interpret. This allows U-Boot to read/write files, print to - the console, and execute arbitrary commands on the host system. - - Enabling this option will add support for reading and writing files - on the host system. If you don't have a debugger attached then trying - to do this will likely cause U-Boot to hang. Say 'n' if you are unsure. - -config SEMIHOSTING_FALLBACK - bool "Recover gracefully when semihosting fails" - depends on SEMIHOSTING && ARM64 - default y - help - Normally, if U-Boot makes a semihosting call and no debugger is - attached, then it will panic due to a synchronous abort - exception. This config adds an exception handler which will allow - U-Boot to recover. Say 'y' if unsure. - -config SPL_SEMIHOSTING - bool "Support ARM semihosting in SPL" - depends on SPL - help - Semihosting is a method for a target to communicate with a host - debugger. It uses special instructions which the debugger will trap - on and interpret. This allows U-Boot to read/write files, print to - the console, and execute arbitrary commands on the host system. - - Enabling this option will add support for reading and writing files - on the host system. If you don't have a debugger attached then trying - to do this will likely cause U-Boot to hang. Say 'n' if you are unsure. - -config SPL_SEMIHOSTING_FALLBACK - bool "Recover gracefully when semihosting fails in SPL" - depends on SPL_SEMIHOSTING && ARM64 - select ARMV8_SPL_EXCEPTION_VECTORS - default y - help - Normally, if U-Boot makes a semihosting call and no debugger is - attached, then it will panic due to a synchronous abort - exception. This config adds an exception handler which will allow - U-Boot to recover. Say 'y' if unsure. - config SYS_THUMB_BUILD bool "Build U-Boot using the Thumb instruction set" depends on !ARM64arch/arm/lib/semihosting.c +1
-180@@ -10,25 +10,11 @@* available in silicon now, fastmodel usage makes less sense for them. */ #include <common.h> -#include <log.h> -#include <semihosting.h> - -#define SYSOPEN 0x01 -#define SYSCLOSE 0x02 -#define SYSWRITEC 0x03 -#define SYSWRITE0 0x04 -#define SYSWRITE 0x05 -#define SYSREAD 0x06 -#define SYSREADC 0x07 -#define SYSISERROR 0x08 -#define SYSSEEK 0x0A -#define SYSFLEN 0x0C -#define SYSERRNO 0x13/* * Call the handler */ -static noinline long smh_trap (unsigned int sysnum,void *addr) +long smh_trap (unsigned int sysnum,void *addr) { registerlong result asm("r0" );#if defined(CONFIG_ARM64 )@@ -41,168 +27,3 @@ static noinline long smh_trap(unsigned int sysnum, void *addr)#endif return result; } - -#if CONFIG_IS_ENABLED (SEMIHOSTING_FALLBACK ) -static bool _semihosting_enabled = true; -static bool try_semihosting = true; - -bool semihosting_enabled (void ) -{ -if (try_semihosting) { -smh_trap (SYSERRNO ,NULL ); - try_semihosting = false; - } - -return _semihosting_enabled; -} - -void disable_semihosting (void ) -{ - _semihosting_enabled = false; -} -#endif - -/** -* smh_errno() - Read the host's errno -* -* This gets the value of the host's errno and negates it. The host's errno may -* or may not be set, so only call this function if a previous semihosting call -* has failed. -* -* Return: a negative error value -*/ -static int smh_errno (void ) -{ -long ret =smh_trap (SYSERRNO ,NULL ); - -if (ret >0 && ret <INT_MAX ) -return -ret; -return -EIO ; -} - -long smh_open (const char *fname,enum smh_open_mode mode) -{ -long fd; -struct smh_open_s { -const char *fname; -unsigned long mode; -size_t len; - } open; - -debug ("%s: file \'%s\', mode \'%u\'\n" , __func__, fname, mode); - - open.fname = fname; - open.len =strlen (fname); - open.mode = mode; - -/* Open the file on the host */ - fd =smh_trap (SYSOPEN , &open); -if (fd ==-1 ) -return smh_errno (); -return fd; -} - -/** -* struct smg_rdwr_s - Arguments for read and write -* @fd: A file descriptor returned from smh_open() -* @memp: Pointer to a buffer of memory of at least @len bytes -* @len: The number of bytes to read or write -*/ -struct smh_rdwr_s { -long fd; -void *memp; -size_t len; -}; - -long smh_read (long fd,void *memp,size_t len) -{ -long ret; -struct smh_rdwr_s read; - -debug ("%s: fd %ld, memp %p, len %zu\n" , __func__, fd, memp, len); - - read.fd = fd; - read.memp = memp; - read.len = len; - - ret =smh_trap (SYSREAD , &read); -if (ret <0 ) -return smh_errno (); -return len - ret; -} - -long smh_write (long fd,const void *memp,size_t len,ulong *written) -{ -long ret; -struct smh_rdwr_s write; - -debug ("%s: fd %ld, memp %p, len %zu\n" , __func__, fd, memp, len); - - write.fd = fd; - write.memp = (void *)memp; - write.len = len; - - ret =smh_trap (SYSWRITE , &write); - *written = len - ret; -if (ret) -return smh_errno (); -return 0 ; -} - -long smh_close (long fd) -{ -long ret; - -debug ("%s: fd %ld\n" , __func__, fd); - - ret =smh_trap (SYSCLOSE , &fd); -if (ret ==-1 ) -return smh_errno (); -return 0 ; -} - -long smh_flen (long fd) -{ -long ret; - -debug ("%s: fd %ld\n" , __func__, fd); - - ret =smh_trap (SYSFLEN , &fd); -if (ret ==-1 ) -return smh_errno (); -return ret; -} - -long smh_seek (long fd,long pos) -{ -long ret; -struct smh_seek_s { -long fd; -long pos; - } seek; - -debug ("%s: fd %ld pos %ld\n" , __func__, fd, pos); - - seek.fd = fd; - seek.pos = pos; - - ret =smh_trap (SYSSEEK , &seek); -if (ret) -return smh_errno (); -return 0 ; -} - -int smh_getc (void ) -{ -return smh_trap (SYSREADC ,NULL ); -} - -void smh_putc (char ch) -{ -smh_trap (SYSWRITEC , &ch); -} - -void smh_puts (const char *s) -{ -smh_trap (SYSWRITE0 , (char *)s); -}include/semihosting.h +11
-0@@ -17,6 +17,17 @@#define SMH_T32_SVC 0xDFAB#define SMH_T32_HLT 0xBABC +/** +* smh_trap() - ARCH-specific semihosting call. +* +* Semihosting library/driver can use this function to do the +* actual semihosting calls. +* +* Return: Error code defined by semihosting spec. +*/ + +long smh_trap (unsigned int sysnum,void *addr); +#if CONFIG_IS_ENABLED (SEMIHOSTING_FALLBACK )/** * semihosting_enabled() - Determine whether semihosting is supported lib/Kconfig +47
-0@@ -71,6 +71,53 @@ config HAVE_PRIVATE_LIBGCC config LIB_UUID bool +config SEMIHOSTING + bool "Support semihosting" + depends on ARM + help + Semihosting is a method for a target to communicate with a host + debugger. It uses special instructions which the debugger will trap + on and interpret. This allows U-Boot to read/write files, print to + the console, and execute arbitrary commands on the host system. + + Enabling this option will add support for reading and writing files + on the host system. If you don't have a debugger attached then trying + to do this will likely cause U-Boot to hang. Say 'n' if you are unsure. + +config SEMIHOSTING_FALLBACK + bool "Recover gracefully when semihosting fails" + depends on SEMIHOSTING && ARM64 + default y + help + Normally, if U-Boot makes a semihosting call and no debugger is + attached, then it will panic due to a synchronous abort + exception. This config adds an exception handler which will allow + U-Boot to recover. Say 'y' if unsure. + +config SPL_SEMIHOSTING + bool "Support semihosting in SPL" + depends on SPL && ARM + help + Semihosting is a method for a target to communicate with a host + debugger. It uses special instructions which the debugger will trap + on and interpret. This allows U-Boot to read/write files, print to + the console, and execute arbitrary commands on the host system. + + Enabling this option will add support for reading and writing files + on the host system. If you don't have a debugger attached then trying + to do this will likely cause U-Boot to hang. Say 'n' if you are unsure. + +config SPL_SEMIHOSTING_FALLBACK + bool "Recover gracefully when semihosting fails in SPL" + depends on SPL_SEMIHOSTING && ARM64 + select ARMV8_SPL_EXCEPTION_VECTORS + default y + help + Normally, if U-Boot makes a semihosting call and no debugger is + attached, then it will panic due to a synchronous abort + exception. This config adds an exception handler which will allow + U-Boot to recover. Say 'y' if unsure. + config PRINTF bool default ylib/Makefile +2
-0@@ -145,6 +145,8 @@ obj-y += date.o obj-y += rtc-lib.o obj-$(CONFIG_LIB_ELF) += elf.o +obj-$(CONFIG_$(SPL_TPL_)SEMIHOSTING) += semihosting.o + # # Build a fast OID lookup registry from include/linux/oid_registry.h #lib/semihosting.c new file +176
-0@@ -0,0 +1,186 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2022 Sean Anderson <[email protected]> +* Copyright 2014 Broadcom Corporation +*/ + +#include <common.h> +#include <log.h> +#include <semihosting.h> + +#define SYSOPEN 0x01 +#define SYSCLOSE 0x02 +#define SYSWRITEC 0x03 +#define SYSWRITE0 0x04 +#define SYSWRITE 0x05 +#define SYSREAD 0x06 +#define SYSREADC 0x07 +#define SYSISERROR 0x08 +#define SYSSEEK 0x0A +#define SYSFLEN 0x0C +#define SYSERRNO 0x13 + +#if CONFIG_IS_ENABLED (SEMIHOSTING_FALLBACK ) +static bool _semihosting_enabled = true; +static bool try_semihosting = true; + +bool semihosting_enabled (void ) +{ +if (try_semihosting) { +smh_trap (SYSERRNO ,NULL ); + try_semihosting = false; + } + +return _semihosting_enabled; +} + +void disable_semihosting (void ) +{ + _semihosting_enabled = false; +} +#endif + +/** +* smh_errno() - Read the host's errno +* +* This gets the value of the host's errno and negates it. The host's errno may +* or may not be set, so only call this function if a previous semihosting call +* has failed. +* +* Return: a negative error value +*/ +static int smh_errno (void ) +{ +long ret =smh_trap (SYSERRNO ,NULL ); + +if (ret >0 && ret <INT_MAX ) +return -ret; +return -EIO ; +} + +long smh_open (const char *fname,enum smh_open_mode mode) +{ +long fd; +struct smh_open_s { +const char *fname; +unsigned long mode; +size_t len; + } open; + +debug ("%s: file \'%s\', mode \'%u\'\n" , __func__, fname, mode); + + open.fname = fname; + open.len =strlen (fname); + open.mode = mode; + +/* Open the file on the host */ + fd =smh_trap (SYSOPEN , &open); +if (fd ==-1 ) +return smh_errno (); +return fd; +} + +/** +* struct smg_rdwr_s - Arguments for read and write +* @fd: A file descriptor returned from smh_open() +* @memp: Pointer to a buffer of memory of at least @len bytes +* @len: The number of bytes to read or write +*/ +struct smh_rdwr_s { +long fd; +void *memp; +size_t len; +}; + +long smh_read (long fd,void *memp,size_t len) +{ +long ret; +struct smh_rdwr_s read; + +debug ("%s: fd %ld, memp %p, len %zu\n" , __func__, fd, memp, len); + + read.fd = fd; + read.memp = memp; + read.len = len; + + ret =smh_trap (SYSREAD , &read); +if (ret <0 ) +return smh_errno (); +return len - ret; +} + +long smh_write (long fd,const void *memp,size_t len,ulong *written) +{ +long ret; +struct smh_rdwr_s write; + +debug ("%s: fd %ld, memp %p, len %zu\n" , __func__, fd, memp, len); + + write.fd = fd; + write.memp = (void *)memp; + write.len = len; + + ret =smh_trap (SYSWRITE , &write); + *written = len - ret; +if (ret) +return smh_errno (); +return 0 ; +} + +long smh_close (long fd) +{ +long ret; + +debug ("%s: fd %ld\n" , __func__, fd); + + ret =smh_trap (SYSCLOSE , &fd); +if (ret ==-1 ) +return smh_errno (); +return 0 ; +} + +long smh_flen (long fd) +{ +long ret; + +debug ("%s: fd %ld\n" , __func__, fd); + + ret =smh_trap (SYSFLEN , &fd); +if (ret ==-1 ) +return smh_errno (); +return ret; +} + +long smh_seek (long fd,long pos) +{ +long ret; +struct smh_seek_s { +long fd; +long pos; + } seek; + +debug ("%s: fd %ld pos %ld\n" , __func__, fd, pos); + + seek.fd = fd; + seek.pos = pos; + + ret =smh_trap (SYSSEEK , &seek); +if (ret) +return smh_errno (); +return 0 ; +} + +int smh_getc (void ) +{ +return smh_trap (SYSREADC ,NULL ); +}
lib/semihosting.c line 186
Quoted 10 lines
lib/semihosting.c new file +10
-0+ +void smh_putc (char ch) +{ +smh_trap (SYSWRITEC , &ch); +} + +void smh_puts (const char *s) +{ +smh_trap (SYSWRITE0 , (char *)s); +}
PATCH v5 2/3 arch/riscv: add semihosting support for RISC-V
In reply to Kautuk ConsulWe add RISC-V semihosting based serial console for JTAG based early debugging.
The RISC-V semihosting specification is available at:
https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adoc
--- arch/riscv/include/asm/spl.h | 1 + arch/riscv/lib/Makefile | 2 ++ arch/riscv/lib/interrupts.c | 25 +++++++++++++++++++++++++ arch/riscv/lib/semihosting.c | 24 ++++++++++++++++++++++++ lib/Kconfig | 10 +++++----- 5 files changed, 57 insertions(+), 5 deletions(-) create mode 100644 arch/riscv/lib/semihosting.c
arch/riscv/include/asm/spl.h +1 -0
@@ -25,6 +25,7 @@ enum {BOOT_DEVICE_DFU ,BOOT_DEVICE_XIP ,BOOT_DEVICE_BOOTROM , +BOOT_DEVICE_SMH , BOOT_DEVICE_NONE };
arch/riscv/lib/Makefile +2 -0
@@ -42,3 +42,5 @@ extra-$(CONFIG_EFI) += $(EFI_CRT0) $(EFI_RELOC) obj-$(CONFIG_$(SPL_TPL_)USE_ARCH_MEMSET) += memset.o obj-$(CONFIG_$(SPL_TPL_)USE_ARCH_MEMMOVE) += memmove.o obj-$(CONFIG_$(SPL_TPL_)USE_ARCH_MEMCPY) += memcpy.o + +obj-$(CONFIG_$(SPL_TPL_)SEMIHOSTING) += semihosting.o
arch/riscv/lib/interrupts.c +25 -0
@@ -9,6 +9,7 @@* Copyright (C) 2019 Sean Anderson <[email protected]> */ +#include <linux/compat.h> #include <common.h> #include <efi_loader.h> #include <hang.h>
@@ -17,6 +18,7 @@#include <asm/ptrace.h> #include <asm/system.h> #include <asm/encoding.h> +#include <semihosting.h> DECLARE_GLOBAL_DATA_PTR ;
@@ -149,6 +151,29 @@ ulong handle_trap(ulong cause, ulong epc, ulong tval, struct pt_regs *regs)/* An UEFI application may have changed gd. Restore U-Boot's gd. */ efi_restore_gd (); +if (cause ==CAUSE_BREAKPOINT && +CONFIG_IS_ENABLED (SEMIHOSTING_FALLBACK )) { +ulong pre_addr = epc -4 , post_addr = epc +4 ; + +/* Check for prior and post addresses to be in same page. */ +if ((pre_addr & ~(PAGE_SIZE -1 )) == + (post_addr & ~(PAGE_SIZE -1 ))) { +u32 pre = *(u32 *)pre_addr; +u32 post = *(u32 *)post_addr; + +/* Check for semihosting, i.e.: +* slli zero,zero,0x1f +* ebreak +* srai zero,zero,0x7 +*/ +if (pre ==0x01f01013 && post ==0x40705013 ) { +disable_semihosting (); + epc +=4 ; +return epc; + } + } + } + is_irq = (cause &MCAUSE_INT ); irq = (cause & ~MCAUSE_INT );
arch/riscv/lib/semihosting.c new file +24 -0
@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2022 Ventana Micro Systems Inc. +*/ + +#include <common.h> + +long smh_trap (int sysnum,void *addr) +{ + register int ret asm ("a0") = sysnum; + register void *param0 asm ("a1") = addr; + + asmvolatile (".align 4\n" +".option push\n" +".option norvc\n" + +"slli zero, zero, 0x1f\n" +"ebreak\n" +"srai zero, zero, 7\n" +".option pop\n" + :"+r" (ret) :"r" (param0) :"memory" ); + +return ret; +}
lib/Kconfig +5 -5
@@ -73,7 +73,7 @@ config LIB_UUID config SEMIHOSTING bool "Support semihosting" - depends on ARM + depends on ARM || RISCV help Semihosting is a method for a target to communicate with a host debugger. It uses special instructions which the debugger will trap
@@ -86,7 +86,7 @@ config SEMIHOSTING config SEMIHOSTING_FALLBACK bool "Recover gracefully when semihosting fails" - depends on SEMIHOSTING && ARM64 + depends on SEMIHOSTING && (ARM64 || RISCV) default y help Normally, if U-Boot makes a semihosting call and no debugger is
@@ -96,7 +96,7 @@ config SEMIHOSTING_FALLBACK config SPL_SEMIHOSTING bool "Support semihosting in SPL" - depends on SPL && ARM + depends on SPL && (ARM || RISCV) help Semihosting is a method for a target to communicate with a host debugger. It uses special instructions which the debugger will trap
@@ -109,8 +109,8 @@ config SPL_SEMIHOSTING config SPL_SEMIHOSTING_FALLBACK bool "Recover gracefully when semihosting fails in SPL" - depends on SPL_SEMIHOSTING && ARM64 - select ARMV8_SPL_EXCEPTION_VECTORS + depends on SPL_SEMIHOSTING && (ARM64 || RISCV) + select ARMV8_SPL_EXCEPTION_VECTORS if ARM64 default y help Normally, if U-Boot makes a semihosting call and no debugger is
Signature · 1 line
2.34.1
Re: [PATCH v5 2/3] arch/riscv: add semihosting support for RISC-V
Quoted 152 lines · Kautuk Consul
We add RISC-V semihosting based serial console for JTAG based early debugging.
The RISC-V semihosting specification is available at:
https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adocSigned-off-by Anup Patel <[email protected]>Signed-off-by Kautuk Consul <[email protected]>--- arch/riscv/include/asm/spl.h | 1 + arch/riscv/lib/Makefile | 2 ++ arch/riscv/lib/interrupts.c | 25 +++++++++++++++++++++++++ arch/riscv/lib/semihosting.c | 24 ++++++++++++++++++++++++ lib/Kconfig | 10 +++++----- 5 files changed, 57 insertions(+), 5 deletions(-) create mode 100644 arch/riscv/lib/semihosting.carch/riscv/include/asm/spl.h +1
-0@@ -25,6 +25,7 @@ enum {BOOT_DEVICE_DFU ,BOOT_DEVICE_XIP ,BOOT_DEVICE_BOOTROM , +BOOT_DEVICE_SMH , BOOT_DEVICE_NONE };arch/riscv/lib/Makefile +2
-0@@ -42,3 +42,5 @@ extra-$(CONFIG_EFI) += $(EFI_CRT0) $(EFI_RELOC) obj-$(CONFIG_$(SPL_TPL_)USE_ARCH_MEMSET) += memset.o obj-$(CONFIG_$(SPL_TPL_)USE_ARCH_MEMMOVE) += memmove.o obj-$(CONFIG_$(SPL_TPL_)USE_ARCH_MEMCPY) += memcpy.o + +obj-$(CONFIG_$(SPL_TPL_)SEMIHOSTING) += semihosting.oarch/riscv/lib/interrupts.c +25
-0@@ -9,6 +9,7 @@* Copyright (C) 2019 Sean Anderson <[email protected]> */ +#include <linux/compat.h> #include <common.h> #include <efi_loader.h> #include <hang.h> @@ -17,6 +18,7 @@#include <asm/ptrace.h> #include <asm/system.h> #include <asm/encoding.h> +#include <semihosting.h> DECLARE_GLOBAL_DATA_PTR ;@@ -149,6 +151,29 @@ ulong handle_trap(ulong cause, ulong epc, ulong tval, struct pt_regs *regs)/* An UEFI application may have changed gd. Restore U-Boot's gd. */ efi_restore_gd (); +if (cause ==CAUSE_BREAKPOINT && +CONFIG_IS_ENABLED (SEMIHOSTING_FALLBACK )) { +ulong pre_addr = epc -4 , post_addr = epc +4 ; + +/* Check for prior and post addresses to be in same page. */ +if ((pre_addr & ~(PAGE_SIZE -1 )) == + (post_addr & ~(PAGE_SIZE -1 ))) { +u32 pre = *(u32 *)pre_addr; +u32 post = *(u32 *)post_addr; + +/* Check for semihosting, i.e.: +* slli zero,zero,0x1f +* ebreak +* srai zero,zero,0x7 +*/ +if (pre ==0x01f01013 && post ==0x40705013 ) { +disable_semihosting (); + epc +=4 ; +return epc; + } + } + } + is_irq = (cause &MCAUSE_INT ); irq = (cause & ~MCAUSE_INT );arch/riscv/lib/semihosting.c new file +24
-0@@ -0,0 +1,24 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* +* Copyright (C) 2022 Ventana Micro Systems Inc. +*/ + +#include <common.h> + +long smh_trap (int sysnum,void *addr) +{ + register int ret asm ("a0") = sysnum; + register void *param0 asm ("a1") = addr; + + asmvolatile (".align 4\n" +".option push\n" +".option norvc\n" + +"slli zero, zero, 0x1f\n" +"ebreak\n" +"srai zero, zero, 7\n" +".option pop\n" + :"+r" (ret) :"r" (param0) :"memory" ); + +return ret; +}lib/Kconfig +3
-3@@ -73,7 +73,7 @@ config LIB_UUID config SEMIHOSTING bool "Support semihosting" - depends on ARM + depends on ARM || RISCV help Semihosting is a method for a target to communicate with a host debugger. It uses special instructions which the debugger will trap@@ -86,7 +86,7 @@ config SEMIHOSTING config SEMIHOSTING_FALLBACK bool "Recover gracefully when semihosting fails" - depends on SEMIHOSTING && ARM64 + depends on SEMIHOSTING && (ARM64 || RISCV) default y help Normally, if U-Boot makes a semihosting call and no debugger is@@ -96,7 +96,7 @@ config SEMIHOSTING_FALLBACK config SPL_SEMIHOSTING bool "Support semihosting in SPL" - depends on SPL && ARM + depends on SPL && (ARM || RISCV) help Semihosting is a method for a target to communicate with a host debugger. It uses special instructions which the debugger will trap
lib/Kconfig config SPL_SEMIHOSTING · line 116
Quoted 10 lines
lib/Kconfig +2
-2@@ -109,8 +109,8 @@ config SPL_SEMIHOSTING config SPL_SEMIHOSTING_FALLBACK bool "Recover gracefully when semihosting fails in SPL" - depends on SPL_SEMIHOSTING && ARM64 - select ARMV8_SPL_EXCEPTION_VECTORS + depends on SPL_SEMIHOSTING && (ARM64 || RISCV) + select ARMV8_SPL_EXCEPTION_VECTORS if ARM64 default y help Normally, if U-Boot makes a semihosting call and no debugger is
A message that is not in the archive (sent off-list or not yet received): HK0PR03MB2994013C655E85AF1F3D2CFBC1229@HK0PR03MB2994.apcprd03.prod.outlook.com
Rick Chen
Reviewed-byRe: [PATCH v5 2/3] arch/riscv: add semihosting support for RISC-V
Quoted 11 lines
From: Kautuk Consul <[email protected]>
Sent: Friday, September 23, 2022 3:03 PM
To: Rayagonda Kokatanur <[email protected]>; Sean Anderson <[email protected]>; Rick Jian-Zhi Chen(陳建志) <[email protected]>; Leo Yu-Chi Liang(梁育齊) <[email protected]>; Bin Meng <[email protected]>; Simon Glass <[email protected]>; Ilias Apalodimas <[email protected]>; Alexandru Gagniuc <[email protected]>; Philippe Reynes <[email protected]>; Heinrich Schuchardt <[email protected]>; Rasmus Villemoes <[email protected]>; Eugen Hristev <[email protected]>; Stefan Roese <[email protected]>; Loic Poulain <[email protected]>; Peng Fan <[email protected]>; Michal Simek <[email protected]>
Cc: [email protected]; Kautuk Consul <[email protected]>; Anup Patel <[email protected]>
Subject: [PATCH v5 2/3]arch/riscv: add semihosting support for RISC-VWe add RISC-V semihosting based serial console for JTAG based early debugging.
The RISC-V semihosting specification is available at:
https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adoc
Quoted 8 lines
Signed-off-by Anup Patel <[email protected]>Signed-off-by Kautuk Consul <[email protected]>--- arch/riscv/include/asm/spl.h | 1 + arch/riscv/lib/Makefile | 2 ++ arch/riscv/lib/interrupts.c | 25 +++++++++++++++++++++++++ arch/riscv/lib/semihosting.c | 24 ++++++++++++++++++++++++ lib/Kconfig | 10 +++++----- 5 files changed, 57 insertions(+), 5 deletions(-) create mode 100644 arch/riscv/lib/semihosting.c
PATCH v5 3/3 board: qemu-riscv: enable semihosting
In reply to Kautuk ConsulTo enable semihosting we also need to enable the following configs in defconfigs:CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FAT
--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)
configs/qemu-riscv32_defconfig +4 -0
@@ -1,4 +1,5 @@ CONFIG_RISCV=y +CONFIG_SEMIHOSTING=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000
@@ -20,3 +21,6 @@ CONFIG_CMD_NVEDIT_EFI=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYS_MAX_FLASH_BANKS=2 +# CONFIG_SERIAL_PUTS is not set +CONFIG_SERIAL_PROBE_ALL=y +CONFIG_SEMIHOSTING_SERIAL=y
configs/qemu-riscv32_smode_defconfig +4 -0
@@ -1,4 +1,5 @@ CONFIG_RISCV=y +CONFIG_SEMIHOSTING=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000
@@ -21,4 +22,7 @@ CONFIG_CMD_NVEDIT_EFI=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYS_MAX_FLASH_BANKS=2 +# CONFIG_SERIAL_PUTS is not set +CONFIG_SERIAL_PROBE_ALL=y +CONFIG_SEMIHOSTING_SERIAL=y CONFIG_SYSRESET_SBI=y
configs/qemu-riscv32_spl_defconfig +7 -0
@@ -1,9 +1,12 @@ CONFIG_RISCV=y +CONFIG_SEMIHOSTING=y +CONFIG_SPL_SEMIHOSTING=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 CONFIG_DEFAULT_DEVICE_TREE="qemu-virt32" CONFIG_SPL=y +CONFIG_SPL_FS_FAT=y CONFIG_SYS_LOAD_ADDR=0x80200000 CONFIG_TARGET_QEMU_VIRT=y CONFIG_RISCV_SMODE=y
@@ -18,6 +21,7 @@ CONFIG_DISPLAY_BOARDINFO=y CONFIG_SPL_MAX_SIZE=0x100000 CONFIG_SPL_BSS_START_ADDR=0x84000000 CONFIG_SYS_SPL_MALLOC=y +CONFIG_SPL_FS_EXT4=y CONFIG_SYS_CBSIZE=256 CONFIG_SYS_PBSIZE=276 CONFIG_SYS_BOOTM_LEN=0x4000000
@@ -25,5 +29,8 @@ CONFIG_SYS_BOOTM_LEN=0x4000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYS_MAX_FLASH_BANKS=2 +# CONFIG_SERIAL_PUTS is not set +CONFIG_SERIAL_PROBE_ALL=y +CONFIG_SEMIHOSTING_SERIAL=y CONFIG_SYSRESET_SBI=y # CONFIG_BINMAN_FDT is not set
configs/qemu-riscv64_defconfig +4 -0
@@ -1,4 +1,5 @@ CONFIG_RISCV=y +CONFIG_SEMIHOSTING=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000
@@ -21,3 +22,6 @@ CONFIG_CMD_NVEDIT_EFI=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYS_MAX_FLASH_BANKS=2 +# CONFIG_SERIAL_PUTS is not set +CONFIG_SERIAL_PROBE_ALL=y +CONFIG_SEMIHOSTING_SERIAL=y
configs/qemu-riscv64_smode_defconfig +4 -0
@@ -1,4 +1,5 @@ CONFIG_RISCV=y +CONFIG_SEMIHOSTING=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000
@@ -24,4 +25,7 @@ CONFIG_CMD_NVEDIT_EFI=y CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYS_MAX_FLASH_BANKS=2 +# CONFIG_SERIAL_PUTS is not set +CONFIG_SERIAL_PROBE_ALL=y +CONFIG_SEMIHOSTING_SERIAL=y CONFIG_SYSRESET_SBI=y
configs/qemu-riscv64_spl_defconfig +7 -0
@@ -1,9 +1,12 @@ CONFIG_RISCV=y +CONFIG_SEMIHOSTING=y +CONFIG_SPL_SEMIHOSTING=y CONFIG_SYS_MALLOC_LEN=0x800000 CONFIG_NR_DRAM_BANKS=1 CONFIG_ENV_SIZE=0x20000 CONFIG_DEFAULT_DEVICE_TREE="qemu-virt64" CONFIG_SPL=y +CONFIG_SPL_FS_FAT=y CONFIG_SYS_LOAD_ADDR=0x80200000 CONFIG_TARGET_QEMU_VIRT=y CONFIG_ARCH_RV64I=y
@@ -18,6 +21,7 @@ CONFIG_DISPLAY_BOARDINFO=y CONFIG_SPL_MAX_SIZE=0x100000 CONFIG_SPL_BSS_START_ADDR=0x84000000 CONFIG_SYS_SPL_MALLOC=y +CONFIG_SPL_FS_EXT4=y CONFIG_SYS_CBSIZE=256 CONFIG_SYS_PBSIZE=276 CONFIG_SYS_BOOTM_LEN=0x4000000
@@ -25,5 +29,8 @@ CONFIG_SYS_BOOTM_LEN=0x4000000 CONFIG_SYS_RELOC_GD_ENV_ADDR=y CONFIG_DM_MTD=y CONFIG_SYS_MAX_FLASH_BANKS=2 +# CONFIG_SERIAL_PUTS is not set +CONFIG_SERIAL_PROBE_ALL=y +CONFIG_SEMIHOSTING_SERIAL=y CONFIG_SYSRESET_SBI=y # CONFIG_BINMAN_FDT is not set
Signature · 1 line
2.34.1
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi Kautuk,
Quoted 10 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATSigned-off-by Kautuk Consul <[email protected]>
Quoted 8 lines
--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)
This patch set seems to cause some CI error.
(https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/13667)
Could you please take a look at it?
Besides, will anything go wrong if we do not attach a debugger but enable semihosting on qemu?
Best regards,
Leo
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi Leo,
I took a look at the raw log.
It seems that the test-case is outputting too many characters onto the u-boot prompt
due to which the log size has gotten exceeded. Can you somehow increase the log size and then try ?
Thanks.
Quoted 31 lines · Leo Liang
Hi Kautuk,
Quoted 10 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATSigned-off-by Kautuk Consul <[email protected]>Quoted 8 lines
--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)This patch set seems to cause some CI error.
(https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/13667)
Could you please take a look at it?Besides, will anything go wrong if we do not attach a debugger but enable semihosting on qemu?
Best regards,
Leo
A message that is not in the archive (sent off-list or not yet received): HK0PR03MB29949257906C387D549119EBC1229@HK0PR03MB2994.apcprd03.prod.outlook.com
Rick Chen
Reviewed-byRe: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Quoted 15 lines
From: Kautuk Consul <[email protected]>
Sent: Friday, September 23, 2022 3:03 PM
To: Rayagonda Kokatanur <[email protected]>; Sean Anderson <[email protected]>; Rick Jian-Zhi Chen(陳建志) <[email protected]>; Leo Yu-Chi Liang(梁育齊) <[email protected]>; Bin Meng <[email protected]>; Simon Glass <[email protected]>; Ilias Apalodimas <[email protected]>; Alexandru Gagniuc <[email protected]>; Philippe Reynes <[email protected]>; Heinrich Schuchardt <[email protected]>; Rasmus Villemoes <[email protected]>; Eugen Hristev <[email protected]>; Stefan Roese <[email protected]>; Loic Poulain <[email protected]>; Peng Fan <[email protected]>; Michal Simek <[email protected]>
Cc: [email protected]; Kautuk Consul <[email protected]>
Subject: [PATCH v5 3/3] board: qemu-riscv: enable semihostingTo enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATSigned-off-by Kautuk Consul <[email protected]>
Quoted 8 lines
--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
In reply to Kautuk ConsulQuoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FAT
Why should these _SPL_FS_xxx be required? If it's required by SEMIHOSTING, could the dependency be fixed there?
Quoted 11 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)
Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FAT
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?
The build dependencies require that these options be there.
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Quoted 16 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FAT
Quoted 5 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
I think you need to fix the dependencies of CONFIG_SPL_SEMIHOSTING
Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
In reply to Kautuk ConsulQuoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FAT
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi,
Quoted 17 lines · Sean Anderson
Quoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FAT
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
If I disable both the _SPL_FS_* config options then I get the following compilation error:common/spl/spl_semihosting.c: In function 'spl_smh_load_image':common/spl/spl_semihosting.c:27:32: error:
'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' undeclared (first use in this function)
27 | const char *filename = CONFIG_SPL_FS_LOAD_PAYLOAD_NAME;
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~common/spl/spl_semihosting.c:27:32: note: each undeclared identifier is reported only once for each function it appears in
Bin/Sean: This error is not really related to the semihosting feature but is related to COFIG_SPL in general.
Can you please accept this patch-set and then I'll try and find time in the future maybe to rectify this build dependency problem ?
Quoted 19 lines
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi Kautuk,
We have tested your patchset with QEMU 7.1.0. It generally looks fine, but CI error seems to persist.
https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/14314
The error comes from CI testcase timed-out.
The reason for the time-out is not yet confirmed, but we suspect it's because when executing under semihosting, QEMU could not exit normally. (thru ctrl+x a)
There is a seemingly relevent patchset that sits on QEMU mailing list for some time.
https://lore.kernel.org/all/[email protected]/T/#m1bc32cc32511b6ac8adfaf67983dc2bccd4b9ec9
On the u-boot side, what do you think if we disable semihosting by default? (i.e., not adding CONFIG_SEMIHOSTING_XXX in qemu's defconfig)
Best regards,
Leo
Quoted 63 lines · Kautuk Consul
Hi,
Quoted 17 lines · Sean Anderson
Quoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATQuoted 6 lines
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
If I disable both the _SPL_FS_* config options then I get the following compilation error:
common/spl/spl_semihosting.c: In function 'spl_smh_load_image':common/spl/spl_semihosting.c:27:32: error:
'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' undeclared (first use in this function)27 | const char *filename = CONFIG_SPL_FS_LOAD_PAYLOAD_NAME; | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
common/spl/spl_semihosting.c:27:32: note: each undeclared identifier is reported only once for each function it appears inBin/Sean: This error is not really related to the semihosting feature but is related to
COFIG_SPLin general.
Can you please accept this patch-set and then I'll try and find time in the future maybe to rectify this build dependency problem ?Quoted 19 lines
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi Leo,
Quoted 12 lines · Leo Liang
Hi Kautuk,
We have tested your patchset with QEMU 7.1.0. It generally looks fine, but CI error seems to persist.
https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/14314The error comes from CI testcase timed-out.
The reason for the time-out is not yet confirmed, but we suspect it's because when executing under semihosting, QEMU could not exit normally. (thru ctrl+x a)
Quoted 5 lines
There is a seemingly relevent patchset that sits on QEMU mailing list for some time.
https://lore.kernel.org/all/[email protected]/T/#m1bc32cc32511b6ac8adfaf67983dc2bccd4b9ec9On the u-boot side, what do you think if we disable semihosting by default? (i.e., not adding
CONFIG_SEMIHOSTING_XXXin qemu's defconfig)
I think it is okay to disable semihosting by default. Then the user will configure it when needed.
So then can you ACK the first 2 patches ? I think we can leave out the 3rd qemu config patch for now.
Quoted 68 lines
Best regards,
LeoQuoted 63 lines · Kautuk Consul
Hi,
Quoted 17 lines · Sean Anderson
Quoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATQuoted 6 lines
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
If I disable both the _SPL_FS_* config options then I get the following compilation error:
common/spl/spl_semihosting.c: In function 'spl_smh_load_image':common/spl/spl_semihosting.c:27:32: error:
'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' undeclared (first use in this function)27 | const char *filename = CONFIG_SPL_FS_LOAD_PAYLOAD_NAME; | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
common/spl/spl_semihosting.c:27:32: note: each undeclared identifier is reported only once for each function it appears inBin/Sean: This error is not really related to the semihosting feature but is related to
COFIG_SPLin general.
Can you please accept this patch-set and then I'll try and find time in the future maybe to rectify this build dependency problem ?Quoted 19 lines
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi Kautuk,
Quoted 18 lines · Kautuk Consul
Hi Leo,
Quoted 15 lines · Leo Liang
Hi Kautuk,
We have tested your patchset with QEMU 7.1.0. It generally looks fine, but CI error seems to persist.
https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/14314The error comes from CI testcase timed-out.
The reason for the time-out is not yet confirmed, but we suspect it's because when executing under semihosting, QEMU could not exit normally. (thru ctrl+x a)There is a seemingly relevent patchset that sits on QEMU mailing list for some time.
https://lore.kernel.org/all/[email protected]/T/#m1bc32cc32511b6ac8adfaf67983dc2bccd4b9ec9
Quoted 8 lines
Quoted 2 lines
On the u-boot side, what do you think if we disable semihosting by default? (i.e., not adding
CONFIG_SEMIHOSTING_XXXin qemu's defconfig)I think it is okay to disable semihosting by default. Then the user will configure it when needed.
So then can you ACK the first 2 patches ? I think we can leave out the 3rd qemu config patch for now.
No problem!
Additionally, could you rebase the patchset to current master, add what Sean suggested, and then send again?
I think I could merge your patch as soon as you re-send it.
Best regards,
Leo
Quoted 68 lines
Quoted 68 lines
Best regards,
LeoQuoted 63 lines · Kautuk Consul
Hi,
Quoted 17 lines · Sean Anderson
Quoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATQuoted 6 lines
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
If I disable both the _SPL_FS_* config options then I get the following compilation error:
common/spl/spl_semihosting.c: In function 'spl_smh_load_image':common/spl/spl_semihosting.c:27:32: error:
'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' undeclared (first use in this function)27 | const char *filename = CONFIG_SPL_FS_LOAD_PAYLOAD_NAME; | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
common/spl/spl_semihosting.c:27:32: note: each undeclared identifier is reported only once for each function it appears inBin/Sean: This error is not really related to the semihosting feature but is related to
COFIG_SPLin general.
Can you please accept this patch-set and then I'll try and find time in the future maybe to rectify this build dependency problem ?Quoted 19 lines
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
Hi Leo,
Thanks! I have sent a v6 of this patchset wherein I have rebased the patchset on the
latest master. I have removed the last patch with default config options for qemu-riscv64
targets and have replaced it with a patch with Sean's suggestion for adding to the
dependencies.
Thanks again.
Quoted 107 lines · Leo Liang
Hi Kautuk,
Quoted 18 lines · Kautuk Consul
Hi Leo,
Quoted 15 lines · Leo Liang
Hi Kautuk,
We have tested your patchset with QEMU 7.1.0. It generally looks fine, but CI error seems to persist.
https://source.denx.de/u-boot/custodians/u-boot-riscv/-/pipelines/14314The error comes from CI testcase timed-out.
The reason for the time-out is not yet confirmed, but we suspect it's because when executing under semihosting, QEMU could not exit normally. (thru ctrl+x a)There is a seemingly relevent patchset that sits on QEMU mailing list for some time.
https://lore.kernel.org/all/[email protected]/T/#m1bc32cc32511b6ac8adfaf67983dc2bccd4b9ec9Quoted 8 lines
Quoted 2 lines
On the u-boot side, what do you think if we disable semihosting by default? (i.e., not adding
CONFIG_SEMIHOSTING_XXXin qemu's defconfig)I think it is okay to disable semihosting by default. Then the user will configure it when needed.
So then can you ACK the first 2 patches ? I think we can leave out the 3rd qemu config patch for now.No problem!
Additionally, could you rebase the patchset to current master, add what Sean suggested, and then send again?
I think I could merge your patch as soon as you re-send it.Best regards,
LeoQuoted 68 lines
Quoted 68 lines
Best regards,
LeoQuoted 63 lines · Kautuk Consul
Hi,
Quoted 17 lines · Sean Anderson
Quoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATQuoted 6 lines
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
If I disable both the _SPL_FS_* config options then I get the following compilation error:
common/spl/spl_semihosting.c: In function 'spl_smh_load_image':common/spl/spl_semihosting.c:27:32: error:
'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' undeclared (first use in this function)27 | const char *filename = CONFIG_SPL_FS_LOAD_PAYLOAD_NAME; | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
common/spl/spl_semihosting.c:27:32: note: each undeclared identifier is reported only once for each function it appears inBin/Sean: This error is not really related to the semihosting feature but is related to
COFIG_SPLin general.
Can you please accept this patch-set and then I'll try and find time in the future maybe to rectify this build dependency problem ?Quoted 19 lines
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Re: [PATCH v5 3/3] board: qemu-riscv: enable semihosting
In reply to Kautuk ConsulQuoted 35 lines · Kautuk Consul
Hi,
Quoted 17 lines · Sean Anderson
Quoted 15 lines · Kautuk Consul
Hi,
Quoted 12 lines · Bin Meng
Quoted 9 lines · Kautuk Consul
To enable semihosting we also need to enable the following configs in defconfigs:
CONFIG_SEMIHOSTINGCONFIG_SPL_SEMIHOSTINGCONFIG_SEMIHOSTING_SERIALCONFIG_SERIAL_PROBE_ALLCONFIG_SPL_FS_EXT4CONFIG_SPL_FS_FATQuoted 6 lines
Quoted 4 lines
Quoted 2 lines
Why should these
_SPL_FS_xxxbe required? If it's required by SEMIHOSTING, could the dependency be fixed there?The build dependencies require that these options be there.
What error do you get?
If I disable both the _SPL_FS_* config options then I get the following compilation error:
common/spl/spl_semihosting.c: In function 'spl_smh_load_image':common/spl/spl_semihosting.c:27:32: error:
'CONFIG_SPL_FS_LOAD_PAYLOAD_NAME' undeclared (first use in this function)27 | const char *filename = CONFIG_SPL_FS_LOAD_PAYLOAD_NAME; | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Quoted 8 lines
common/spl/spl_semihosting.c:27:32: note: each undeclared identifier is reported only once for each function it appears inBin/Sean: This error is not really related to the semihosting feature but is related to
COFIG_SPLin general.
Can you please accept this patch-set and then I'll try and find time in the future maybe to rectify this build dependency problem ?
config SPL_FS_LOAD_PAYLOAD_NAME
string "File to load for U-Boot from the filesystem" depends on SPL_FS_EXT4 || SPL_FS_FAT || SPL_FS_SQUASHFS default "tispl.bin" if SYS_K3_SPL_ATF
default "u-boot.itb" if SPL_LOAD_FIT
default "u-boot.img"
help
Filename to read to load U-Boot when reading from filesystem.
Add CONFIG_SPL_SEMIHOSTING to the depends.
--Sean
Quoted 19 lines
Quoted 19 lines
--Sean
Quoted 15 lines
Quoted 15 lines
Quoted 12 lines
Signed-off-by Kautuk Consul <[email protected]>--- configs/qemu-riscv32_defconfig | 4 ++++ configs/qemu-riscv32_smode_defconfig | 4 ++++ configs/qemu-riscv32_spl_defconfig | 7 +++++++ configs/qemu-riscv64_defconfig | 4 ++++ configs/qemu-riscv64_smode_defconfig | 4 ++++ configs/qemu-riscv64_spl_defconfig | 7 +++++++ 6 files changed, 30 insertions(+)Regards,
Bin
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent days.
Thanks.
Quoted 70 lines · Kautuk Consul
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
(quoted diff) +0
-2- Check arch dependencies for SEMIHOSTING as well as SPL_SEMIHOSTING config options as per Sean's comment. - arch/riscv/lib/interrupts.c: Check for post and pre instructions of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a disable_semihosting and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binU-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000Kautuk Consul (3):
lib: Add common semihosting libraryarch/riscv: add semihosting support for RISC-V
board: qemu-riscv: enable semihostingarch/arm/Kconfig | 46 ------- arch/arm/lib/semihosting.c | 181 +------------------------- arch/riscv/include/asm/spl.h | 1 + arch/riscv/lib/Makefile | 2 + arch/riscv/lib/interrupts.c | 25 ++++ arch/riscv/lib/semihosting.c | 24 ++++ configs/qemu-riscv32_defconfig | 4 + configs/qemu-riscv32_smode_defconfig | 4 + configs/qemu-riscv32_spl_defconfig | 7 + configs/qemu-riscv64_defconfig | 4 + configs/qemu-riscv64_smode_defconfig | 4 + configs/qemu-riscv64_spl_defconfig | 7 + include/semihosting.h | 11 ++ lib/Kconfig | 47 +++++++ lib/Makefile | 2 + lib/semihosting.c | 186 +++++++++++++++++++++++++++ 16 files changed, 329 insertions(+), 226 deletions(-) create mode 100644 arch/riscv/lib/semihosting.c create mode 100644 lib/semihosting.c--
2.34.1
Hi Kautuk,
Quoted 52 lines · Kautuk Consul
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent days.
Thanks.
Quoted 42 lines · Kautuk Consul
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
(quoted diff) +0
-2- Check arch dependencies for SEMIHOSTING as well as SPL_SEMIHOSTING config options as per Sean's comment. - arch/riscv/lib/interrupts.c: Check for post and pre instructions of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a disable_semihosting and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binU-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000
Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
I have tested it both on Qemu and Ventana's internal simulator.
Quoted 66 lines · Bin Meng
Hi Kautuk,
Quoted 6 lines · Kautuk Consul
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent
days.
Quoted 4 lines
Thanks.
On Fri, Sep 23, 2022 at 12:33 PM Kautuk Consul <[email protected]>
Quoted 9 lines · wrote:
Quoted 9 lines
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
- Check arch dependencies for SEMIHOSTING as well as
SPL_SEMIHOSTINGQuoted 21 lines
Quoted 21 lines
config options as per Sean's comment.
-arch/riscv/lib/interrupts.c: Check for post and pre instructions
of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do adisable_semihostingand epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binQuoted 12 lines
Quoted 12 lines
U-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
Hi Kautuk,
Sorry for the late reply.
The CI failure still exists and
if tested on QEMU(7.0.0) without a gdb attached, it is possible that we get weird output on console.[1]
Another thing is that with your patch, QEMU could not exit with Ctrl a + x.
This might be the reason for CI failure (timeout). Could you take a look at this?
Yet with a gdb attached, everything works as expected, So maybe we could disable semihosting as default?
Best regards,
Leo
[1] The weird console output looks like below, it outputs random character without us typing anything.
U-Boot 2022.10-rc5 (Dec 02 2022 - 16:27:43 +0800)
CPU: rv64imafdcsuh Model: riscv-virtio,qemu DRAM: 2 GiB Core: 35 devices, 15 uclasses, devicetree: board Flash: 32 MiB Loading Environment from nowhere... OK In: serial_semihosting Out: serial_semihosting Err: serial_semihosting Net: eth0: virtio-net#1 Hit any key to stop autoboot: 0
=> 55555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555 55555555555555555555555555555555555555555555555555555555555555555555
Quoted 70 lines · Kautuk Consul
I have tested it both on Qemu and Ventana's internal simulator.
Quoted 66 lines · Bin Meng
Hi Kautuk,
Quoted 6 lines · Kautuk Consul
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent
days.
Quoted 4 lines
Thanks.
On Fri, Sep 23, 2022 at 12:33 PM Kautuk Consul <[email protected]>
Quoted 9 lines · wrote:
Quoted 9 lines
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
- Check arch dependencies for SEMIHOSTING as well as
SPL_SEMIHOSTINGQuoted 21 lines
Quoted 21 lines
config options as per Sean's comment.
-arch/riscv/lib/interrupts.c: Check for post and pre instructions
of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do adisable_semihostingand epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binQuoted 12 lines
Quoted 12 lines
U-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
Hi Leo,
What Qemu version are you using.
Can you please try with QEMU 7.1 or later ?
There is a fix which was merged after 7.0.
Thanks.
Quoted 117 lines · Leo Liang
Hi Kautuk,
Sorry for the late reply.
The CI failure still exists and
if tested on QEMU(7.0.0) without a gdb attached, it is possible that we get weird output on console.[1]Another thing is that with your patch, QEMU could not exit with Ctrl a + x.
This might be the reason for CI failure (timeout). Could you take a look at this?Yet with a gdb attached, everything works as expected, So maybe we could disable semihosting as default?
Best regards,
Leo[1] The weird console output looks like below, it outputs random character without us typing anything.
U-Boot 2022.10-rc5 (Dec 02 2022 - 16:27:43 +0800)
CPU: rv64imafdcsuh Model: riscv-virtio,qemu DRAM: 2 GiB Core: 35 devices, 15 uclasses, devicetree: board Flash: 32 MiB Loading Environment from nowhere... OK In: serial_semihosting Out: serial_semihosting Err: serial_semihosting Net: eth0: virtio-net#1 Hit any key to stop autoboot: 0=> 55555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555 55555555555555555555555555555555555555555555555555555555555555555555
Quoted 7 lines · Kautuk Consul
I have tested it both on Qemu and Ventana's internal simulator.
Quoted 3 lines · Bin Meng
Hi Kautuk,
On Tue, Nov 29, 2022 at 2:29 PM Kautuk Consul <
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines · wrote:
Hi,
Quoted 8 lines
Quoted 8 lines
Quoted 3 lines
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent
days.
Quoted 4 lines
Thanks.
On Fri, Sep 23, 2022 at 12:33 PM Kautuk Consul <
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines · wrote:
Quoted 7 lines
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
CHANGES since v4:
- Check arch dependencies for SEMIHOSTING as well as
SPL_SEMIHOSTINGQuoted 2 lines
Quoted 2 lines
config options as per Sean's comment.
-arch/riscv/lib/interrupts.c: Check for post and preinstructions
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a
disable_semihostingQuoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio-bios\
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binU-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio-bios\
Quoted 10 lines
Quoted 10 lines
Quoted 3 lines
Quoted 3 lines
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
Hi Kautuk,
Quoted 5 lines · Kautuk Consul
Hi Leo,
What Qemu version are you using.
Can you please try with QEMU 7.1 or later ?
There is a fix which was merged after 7.0.
Got it!
I'll try with QEMU 7.1 and see if the issue still exists. Thanks!
Best regards,
Leo
Quoted 122 lines
Thanks.
Quoted 117 lines · Leo Liang
Hi Kautuk,
Sorry for the late reply.
The CI failure still exists and
if tested on QEMU(7.0.0) without a gdb attached, it is possible that we get weird output on console.[1]Another thing is that with your patch, QEMU could not exit with Ctrl a + x.
This might be the reason for CI failure (timeout). Could you take a look at this?Yet with a gdb attached, everything works as expected, So maybe we could disable semihosting as default?
Best regards,
Leo[1] The weird console output looks like below, it outputs random character without us typing anything.
U-Boot 2022.10-rc5 (Dec 02 2022 - 16:27:43 +0800)
CPU: rv64imafdcsuh Model: riscv-virtio,qemu DRAM: 2 GiB Core: 35 devices, 15 uclasses, devicetree: board Flash: 32 MiB Loading Environment from nowhere... OK In: serial_semihosting Out: serial_semihosting Err: serial_semihosting Net: eth0: virtio-net#1 Hit any key to stop autoboot: 0=> 55555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555555 55555555555555555555555555555555555555555555555555555555555555555555
Quoted 7 lines · Kautuk Consul
I have tested it both on Qemu and Ventana's internal simulator.
Quoted 3 lines · Bin Meng
Hi Kautuk,
On Tue, Nov 29, 2022 at 2:29 PM Kautuk Consul <
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines · wrote:
Hi,
Quoted 8 lines
Quoted 8 lines
Quoted 3 lines
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent
days.
Quoted 4 lines
Thanks.
On Fri, Sep 23, 2022 at 12:33 PM Kautuk Consul <
Quoted 8 lines
Quoted 8 lines
Quoted 7 lines · wrote:
Quoted 7 lines
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
Quoted 5 lines
Quoted 5 lines
Quoted 2 lines
Quoted 2 lines
CHANGES since v4:
- Check arch dependencies for SEMIHOSTING as well as
SPL_SEMIHOSTINGQuoted 2 lines
Quoted 2 lines
config options as per Sean's comment.
-arch/riscv/lib/interrupts.c: Check for post and preinstructions
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a
disable_semihostingQuoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio-bios\
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
Quoted 12 lines
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binU-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio-bios\
Quoted 10 lines
Quoted 10 lines
Quoted 3 lines
Quoted 3 lines
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
Quoted 2 lines · Kautuk Consul
I have tested it both on Qemu and Ventana's internal simulator.
How to verify this? I used your instructions and U-Boot says: No match for driver 'serial_semihosting'
U-Boot 2023.01-rc2-00113-g2a4accaf5e (Dec 03 2022 - 12:20:20 +0800)
CPU: rv64imafdch_zicsr_zifencei_zihintpause_zba_zbb_zbc_zbs_sstc
Model: riscv-virtio,qemu
DRAM: 256 MiB
No match for driver 'serial_semihosting'
Some drivers were not found
Core: 25 devices, 12 uclasses, devicetree: board
Flash: 32 MiB
Loading Environment from nowhere... OK
In: serial@10000000
Out: serial@10000000
Err: serial@10000000
Net: No ethernet found.
Working FDT set to 8f734950
Hit any key to stop autoboot: 0
=>
Quoted 59 lines · Bin Meng
Quoted 57 lines
Hi Kautuk,
Quoted 52 lines · Kautuk Consul
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent days.
Thanks.
Quoted 42 lines · Kautuk Consul
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
(quoted diff) +0
-2- Check arch dependencies for SEMIHOSTING as well as SPL_SEMIHOSTING config options as per Sean's comment. - arch/riscv/lib/interrupts.c: Check for post and pre instructions of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a disable_semihosting and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binU-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000
Quoted 3 lines
Quoted 3 lines
Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
Hi Kautuk,
Quoted 8 lines · Bin Meng
Quoted 2 lines · Kautuk Consul
I have tested it both on Qemu and Ventana's internal simulator.
How to verify this? I used your instructions and U-Boot says: No match for driver '
serial_semihosting'
Quoted 62 lines
U-Boot 2023.01-rc2-00113-g2a4accaf5e (Dec 03 2022 - 12:20:20 +0800)
CPU:rv64imafdch_zicsr_zifencei_zihintpause_zba_zbb_zbc_zbs_sstc
Model: riscv-virtio,qemu
DRAM: 256 MiB
No match for driver 'serial_semihosting'
Some drivers were not found
Core: 25 devices, 12 uclasses, devicetree: board
Flash: 32 MiB
Loading Environment from nowhere... OK
In: serial@10000000
Out: serial@10000000
Err: serial@10000000
Net: No ethernet found.
Working FDT set to8f734950
Hit any key to stop autoboot: 0
=>Quoted 45 lines · Bin Meng
Quoted 43 lines
Hi Kautuk,
Quoted 39 lines · Kautuk Consul
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in recent days.
Thanks.
Quoted 29 lines · Kautuk Consul
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
(quoted diff) +0
-2- Check arch dependencies for SEMIHOSTING as well as SPL_SEMIHOSTING config options as per Sean's comment. - arch/riscv/lib/interrupts.c: Check for post and pre instructions of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a disable_semihosting and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.bin
It turns out your instructions missed "-semihosting" in the QEMU command line.
With that I can see U-Boot boots with the serial_semihosting driver.
Quoted 14 lines
Quoted 14 lines
Quoted 14 lines
Quoted 13 lines
Quoted 13 lines
U-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio -bios\
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000
Quoted 4 lines
Quoted 3 lines
Quoted 3 lines
Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin
Sorry about that! I assumed everyone would know the option and decided to just upt the ordinary command
to show that the semihosting changes don't impact the non-semihosting scenarios.
Quoted 110 lines · Bin Meng
Hi Kautuk,
Quoted 2 lines · Bin Meng
On Tue, Nov 29, 2022 at 2:58 PM Kautuk Consul <[email protected]>
Quoted 29 lines · wrote:
Quoted 2 lines
I have tested it both on Qemu and Ventana's internal simulator.
How to verify this? I used your instructions and U-Boot says: No match for driver '
serial_semihosting'U-Boot 2023.01-rc2-00113-g2a4accaf5e (Dec 03 2022 - 12:20:20 +0800)
CPU:rv64imafdch_zicsr_zifencei_zihintpause_zba_zbb_zbc_zbs_sstc
Model: riscv-virtio,qemu
DRAM: 256 MiB
No match for driver 'serial_semihosting'
Some drivers were not found
Core: 25 devices, 12 uclasses, devicetree: board
Flash: 32 MiB
Loading Environment from nowhere... OK
In: serial@10000000
Out: serial@10000000
Err: serial@10000000
Net: No ethernet found.
Working FDT set to8f734950
Hit any key to stop autoboot: 0
=>Quoted 6 lines · Bin Meng
Quoted 4 lines
Hi Kautuk,
On Tue, Nov 29, 2022 at 2:29 PM Kautuk Consul <
Quoted 6 lines · [email protected]> wrote:
Quoted 6 lines
Quoted 6 lines
Quoted 6 lines
Hi,
Can someone pick this patchset up ?
It has been reviewed and there has been no comment on this in
recent days.
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Quoted 4 lines
Thanks.
On Fri, Sep 23, 2022 at 12:33 PM Kautuk Consul <
Quoted 9 lines · [email protected]> wrote:
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Semihosting is a mechanism that enables code running on a target to communicate and use the Input/Output facilities on a host computer that is running a debugger. This patchset adds support for semihosting in u-boot for RISCV64 targets.
CHANGES since v4:
- Check arch dependencies for SEMIHOSTING as well as
SPL_SEMIHOSTINGQuoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
config options as per Sean's comment.
-arch/riscv/lib/interrupts.c: Check for post and preinstructions
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
of the ebreak statement whether they are as per the RISCV semihosting specification. Only then do a
disable_semihostingQuoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
and epc += 4 and return.Compilation and test commands for SPL and S-mode configurations
=================================================================Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
U-Boot S-mode on QEMU virt
----------------------------
// Compilation of S-mode u-boot
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_smode_defconfig
make
// Run riscv 64-bit u-boot with opensbi on qemu qemu-system-riscv64 -M virt -m 256M -display none -serial stdio-bios\
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
Quoted 2 lines
opensbi/build/platform/generic/firmware/fw_jump.bin -kernel\
u-boot/u-boot.binIt turns out your instructions missed "-semihosting" in the QEMU command line.
With that I can see U-Boot boots with the
serial_semihostingdriver.Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
Quoted 10 lines
U-Boot SPL on QEMU virt
------------------------
// Compilation of u-boot-spl
ARCH=riscv
CROSS_COMPILE=riscv64-unknown-linux-gnu-
make qemu-riscv64_spl_defconfig
make OPENSBI=opensbi/build/platform/generic/firmware/fw_dynamic.bin // Run 64-bit u-boot-spl in qemu
qemu-system-riscv64 -M virt -m 256M -display none -serial stdio-bios\
Quoted 8 lines
Quoted 7 lines
Quoted 7 lines
Quoted 3 lines
Quoted 3 lines
u-boot/spl/u-boot-spl.bin -device\
loader,file=u-boot/u-boot.itb,addr=0x80200000Do you have instructions on how to actually test semihosting? Does it require a JTAG debugger? But I see you are using QEMU?
Regards,
Bin