board: tbs2910: Set all board dts files as maintained
PATCH 1/2 board: tbs2910: Set all board dts files as maintained
This also includes the imx6q-tbs2910-u-boot.dtsi file now.
---
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: [email protected]
--- board/tbs/tbs2910/MAINTAINERS | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
board/tbs/tbs2910/MAINTAINERS +1 -1
@@ -1,7 +1,7 @@ TBS2910 BOARD M: Soeren Moch <[email protected]> S: Maintained -F: arch/arm/dts/imx6q-tbs2910.dts +F: arch/arm/dts/imx6q-tbs2910* F: board/tbs/tbs2910/ F: configs/tbs2910_defconfig F: doc/board/tbs/
--
2.34.1
PATCH 2/2 board: tbs2910: Add serial rx buffer in defconfig
... to avoid loosing characters when pasting text into the serial console. This allows to remove the workaround to disable the vidconsole output when no HDMI device is detected. This workaround only was there to speed-up serial console processing.
---
Cc: Stefano Babic <[email protected]>
Cc: Fabio Estevam <[email protected]>
Cc: "NXP i.MX U-Boot Team" <[email protected]>
Cc: [email protected]
--- configs/tbs2910_defconfig | 3 ++- include/configs/tbs2910.h | 4 ---- 2 files changed, 2 insertions(+), 5 deletions(-)
configs/tbs2910_defconfig +2 -1
@@ -24,7 +24,7 @@ CONFIG_BOOTDELAY=3 CONFIG_USE_BOOTCOMMAND=y CONFIG_BOOTCOMMAND="mmc rescan; if run bootcmd_up1; then run bootcmd_up2; else run bootcmd_mmc || run distro_bootcmd; fi" CONFIG_USE_PREBOOT=y -CONFIG_PREBOOT="echo PCI:; pci enum; pci 1; usb start; if hdmidet; then run set_con_hdmi; else run set_con_serial; fi" +CONFIG_PREBOOT="echo PCI:; pci enum; pci 1; usb start" CONFIG_DEFAULT_FDT_FILE="imx6q-tbs2910.dtb" CONFIG_PRE_CONSOLE_BUFFER=y CONFIG_HUSH_PARSER=y
@@ -89,6 +89,7 @@ CONFIG_PINCTRL_IMX6=y CONFIG_DM_RTC=y CONFIG_RTC_DS1307=y CONFIG_DM_SERIAL=y +CONFIG_SERIAL_RX_BUFFER=y CONFIG_MXC_UART=y CONFIG_DM_THERMAL=y CONFIG_IMX_THERMAL=y
include/configs/tbs2910.h +0 -4
@@ -61,10 +61,6 @@"pxefile_addr_r=0x10100000\0" \"ramdisk_addr_r=0x18080000\0" \"scriptaddr=0x10000000\0" \ -"set_con_serial=setenv stdout serial; " \ -"setenv stderr serial\0" \ -"set_con_hdmi=setenv stdout serial,vidconsole; " \ -"setenv stderr serial,vidconsole\0" \"stderr=serial,vidconsole\0" \"stdin=serial,usbkbd\0" \"stdout=serial,vidconsole\0"
--
2.34.1
Re: [PATCH 2/2] board: tbs2910: Add serial rx buffer in defconfig
Quoted 7 lines · Soeren Moch
... to avoid loosing characters when pasting text into the serial console. This allows to remove the workaround to disable the vidconsole output when no HDMI device is detected. This workaround only was there to speed-up serial console processing.
Signed-off-by Soeren Moch <[email protected]>
Re: [PATCH 2/2] board: tbs2910: Add serial rx buffer in defconfig
Quoted 8 lines · Fabio Estevam
Quoted 6 lines · Soeren Moch
... to avoid loosing characters when pasting text into the serial console. This allows to remove the workaround to disable the vidconsole output when no HDMI device is detected. This workaround only was there to speed-up serial console processing.
Signed-off-by Soeren Moch <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Thanks, Fabio!
I forgot to mention: This is not urgent. It is totally fine to queue this series for -next.
Thanks,
Soeren
PATCH 2/2 board: tbs2910: Add serial rx buffer in defconfig
In reply to Soeren MochQuoted 6 lines
... to avoid loosing characters when pasting text into the serial console. This allows to remove the workaround to disable the vidconsole output when no HDMI device is detected. This workaround only was there to speed-up serial console processing.
Signed-off-by Soeren Moch <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================
Quoted 4 lines · Soeren Moch
This also includes the
imx6q-tbs2910-u-boot.dtsifile now.Signed-off-by Soeren Moch <[email protected]>
PATCH 1/2 board: tbs2910: Set all board dts files as maintained
In reply to Soeren MochQuoted 3 lines
This also includes the
imx6q-tbs2910-u-boot.dtsifile now.Signed-off-by Soeren Moch <[email protected]>Reviewed-by Fabio Estevam <[email protected]>
Applied to u-boot-imx, master, thanks !
Best regards,
Stefano Babic
Signature · 5 lines
===================================================================== DENX Software Engineering GmbH, Managing Director: Wolfgang Denk HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected] =====================================================================